From: Heiner Kallweit <hkallweit1@gmail.com>
To: Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
David Miller <davem@davemloft.net>
Cc: "netdev@vger.kernel.org" <netdev@vger.kernel.org>
Subject: [PATCH net-next 3/3] net: phy: realtek: use genphy_read_abilities
Date: Wed, 27 Mar 2019 22:00:32 +0100 [thread overview]
Message-ID: <6f6b620c-f109-43b9-f39a-6c4970386da9@gmail.com> (raw)
In-Reply-To: <3d087449-a68f-8233-e97f-29038f8de29a@gmail.com>
Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
---
drivers/net/phy/realtek.c | 36 ++++++++++++------------------------
1 file changed, 12 insertions(+), 24 deletions(-)
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
index 10df52ccd..5ecbd41ed 100644
--- a/drivers/net/phy/realtek.c
+++ b/drivers/net/phy/realtek.c
@@ -151,21 +151,14 @@ static int rtl8211_config_aneg(struct phy_device *phydev)
static int rtl8211c_config_init(struct phy_device *phydev)
{
/* RTL8211C has an issue when operating in Gigabit slave mode */
- phy_set_bits(phydev, MII_CTRL1000,
- CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER);
-
- return genphy_config_init(phydev);
+ return phy_set_bits(phydev, MII_CTRL1000,
+ CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER);
}
static int rtl8211f_config_init(struct phy_device *phydev)
{
- int ret;
u16 val = 0;
- ret = genphy_config_init(phydev);
- if (ret < 0)
- return ret;
-
/* enable TX-delay for rgmii-id and rgmii-txid, otherwise disable it */
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
@@ -192,10 +185,6 @@ static int rtl8366rb_config_init(struct phy_device *phydev)
{
int ret;
- ret = genphy_config_init(phydev);
- if (ret < 0)
- return ret;
-
ret = phy_set_bits(phydev, RTL8366RB_POWER_SAVE,
RTL8366RB_POWER_SAVE_ON);
if (ret) {
@@ -210,11 +199,11 @@ static struct phy_driver realtek_drvs[] = {
{
PHY_ID_MATCH_EXACT(0x00008201),
.name = "RTL8201CP Ethernet",
- .features = PHY_BASIC_FEATURES,
+ .get_features = genphy_read_abilities,
}, {
PHY_ID_MATCH_EXACT(0x001cc816),
.name = "RTL8201F Fast Ethernet",
- .features = PHY_BASIC_FEATURES,
+ .get_features = genphy_read_abilities,
.ack_interrupt = &rtl8201_ack_interrupt,
.config_intr = &rtl8201_config_intr,
.suspend = genphy_suspend,
@@ -224,14 +213,14 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc910),
.name = "RTL8211 Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.config_aneg = rtl8211_config_aneg,
.read_mmd = &genphy_read_mmd_unsupported,
.write_mmd = &genphy_write_mmd_unsupported,
}, {
PHY_ID_MATCH_EXACT(0x001cc912),
.name = "RTL8211B Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.ack_interrupt = &rtl821x_ack_interrupt,
.config_intr = &rtl8211b_config_intr,
.read_mmd = &genphy_read_mmd_unsupported,
@@ -241,14 +230,14 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc913),
.name = "RTL8211C Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.config_init = rtl8211c_config_init,
.read_mmd = &genphy_read_mmd_unsupported,
.write_mmd = &genphy_write_mmd_unsupported,
}, {
PHY_ID_MATCH_EXACT(0x001cc914),
.name = "RTL8211DN Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.ack_interrupt = rtl821x_ack_interrupt,
.config_intr = rtl8211e_config_intr,
.suspend = genphy_suspend,
@@ -256,7 +245,7 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc915),
.name = "RTL8211E Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.ack_interrupt = &rtl821x_ack_interrupt,
.config_intr = &rtl8211e_config_intr,
.suspend = genphy_suspend,
@@ -264,7 +253,7 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc916),
.name = "RTL8211F Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.config_init = &rtl8211f_config_init,
.ack_interrupt = &rtl8211f_ack_interrupt,
.config_intr = &rtl8211f_config_intr,
@@ -275,8 +264,7 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc800),
.name = "Generic Realtek PHY",
- .features = PHY_GBIT_FEATURES,
- .config_init = genphy_config_init,
+ .get_features = genphy_read_abilities,
.suspend = genphy_suspend,
.resume = genphy_resume,
.read_page = rtl821x_read_page,
@@ -284,7 +272,7 @@ static struct phy_driver realtek_drvs[] = {
}, {
PHY_ID_MATCH_EXACT(0x001cc961),
.name = "RTL8366RB Gigabit Ethernet",
- .features = PHY_GBIT_FEATURES,
+ .get_features = genphy_read_abilities,
.config_init = &rtl8366rb_config_init,
/* These interrupts are handled by the irq controller
* embedded inside the RTL8366RB, they get unmasked when the
--
2.21.0
next prev parent reply other threads:[~2019-03-27 21:00 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-27 20:57 [PATCH net-next 0/3] net: phy: add and use new function genphy_read_abilities Heiner Kallweit
2019-03-27 20:58 ` [PATCH net-next 1/3] net: phy: add genphy_read_abilities Heiner Kallweit
2019-03-27 20:59 ` [PATCH net-next 2/3] net: phy: use genphy_read_abilities in genphy driver Heiner Kallweit
2019-03-27 21:00 ` Heiner Kallweit [this message]
2019-03-29 20:26 ` [PATCH net-next 0/3] net: phy: add and use new function genphy_read_abilities David Miller
2019-04-02 20:10 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6f6b620c-f109-43b9-f39a-6c4970386da9@gmail.com \
--to=hkallweit1@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).