* [PATCH v3 1/2] Documentation: net: dsa: Describe DSA switch configuration
2019-07-05 9:57 [PATCH v3 0/2] Document the configuration of b53 Benedikt Spranger
@ 2019-07-05 9:57 ` Benedikt Spranger
2019-07-05 15:40 ` Florian Fainelli
2019-07-05 9:57 ` [PATCH v3 2/2] Documentation: net: dsa: b53: Describe b53 configuration Benedikt Spranger
2019-07-08 22:30 ` [PATCH v3 0/2] Document the configuration of b53 David Miller
2 siblings, 1 reply; 6+ messages in thread
From: Benedikt Spranger @ 2019-07-05 9:57 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Sebastian Andrzej Siewior, Kurt Kanzenbach, Andrew Lunn,
Vivien Didelot
Document DSA tagged and VLAN based switch configuration by showcases.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
.../networking/dsa/configuration.rst | 292 ++++++++++++++++++
Documentation/networking/dsa/index.rst | 1 +
2 files changed, 293 insertions(+)
create mode 100644 Documentation/networking/dsa/configuration.rst
diff --git a/Documentation/networking/dsa/configuration.rst b/Documentation/networking/dsa/configuration.rst
new file mode 100644
index 000000000000..3260ee81cb6e
--- /dev/null
+++ b/Documentation/networking/dsa/configuration.rst
@@ -0,0 +1,292 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=======================================
+DSA switch configuration from userspace
+=======================================
+
+The DSA switch configuration is not integrated into the main userspace
+network configuration suites by now and has to be performed manualy.
+
+.. _dsa-config-showcases:
+
+Configuration showcases
+-----------------------
+
+To configure a DSA switch a couple of commands need to be executed. In this
+documentation some common configuration scenarios are handled as showcases:
+
+*single port*
+ Every switch port acts as a different configurable Ethernet port
+
+*bridge*
+ Every switch port is part of one configurable Ethernet bridge
+
+*gateway*
+ Every switch port except one upstream port is part of a configurable
+ Ethernet bridge.
+ The upstream port acts as different configurable Ethernet port.
+
+All configurations are performed with tools from iproute2, which is available
+at https://www.kernel.org/pub/linux/utils/net/iproute2/
+
+Through DSA every port of a switch is handled like a normal linux Ethernet
+interface. The CPU port is the switch port connected to an Ethernet MAC chip.
+The corresponding linux Ethernet interface is called the master interface.
+All other corresponding linux interfaces are called slave interfaces.
+
+The slave interfaces depend on the master interface. They can only brought up,
+when the master interface is up.
+
+In this documentation the following Ethernet interfaces are used:
+
+*eth0*
+ the master interface
+
+*lan1*
+ a slave interface
+
+*lan2*
+ another slave interface
+
+*lan3*
+ a third slave interface
+
+*wan*
+ A slave interface dedicated for upstream traffic
+
+Further Ethernet interfaces can be configured similar.
+The configured IPs and networks are:
+
+*single port*
+ * lan1: 192.0.2.1/30 (192.0.2.0 - 192.0.2.3)
+ * lan2: 192.0.2.5/30 (192.0.2.4 - 192.0.2.7)
+ * lan3: 192.0.2.9/30 (192.0.2.8 - 192.0.2.11)
+
+*bridge*
+ * br0: 192.0.2.129/25 (192.0.2.128 - 192.0.2.255)
+
+*gateway*
+ * br0: 192.0.2.129/25 (192.0.2.128 - 192.0.2.255)
+ * wan: 192.0.2.1/30 (192.0.2.0 - 192.0.2.3)
+
+.. _dsa-tagged-configuration:
+
+Configuration with tagging support
+----------------------------------
+
+The tagging based configuration is desired and supported by the majority of
+DSA switches. These switches are capable to tag incoming and outgoing traffic
+without using a VLAN based configuration.
+
+single port
+~~~~~~~~~~~
+
+.. code-block:: sh
+
+ # configure each interface
+ ip addr add 192.0.2.1/30 dev lan1
+ ip addr add 192.0.2.5/30 dev lan2
+ ip addr add 192.0.2.9/30 dev lan3
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+
+ # bring up the slave interfaces
+ ip link set lan1 up
+ ip link set lan2 up
+ ip link set lan3 up
+
+bridge
+~~~~~~
+
+.. code-block:: sh
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+
+ # bring up the slave interfaces
+ ip link set lan1 up
+ ip link set lan2 up
+ ip link set lan3 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # add ports to bridge
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+ ip link set dev lan3 master br0
+
+ # configure the bridge
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge
+ ip link set dev br0 up
+
+gateway
+~~~~~~~
+
+.. code-block:: sh
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+
+ # bring up the slave interfaces
+ ip link set wan up
+ ip link set lan1 up
+ ip link set lan2 up
+
+ # configure the upstream port
+ ip addr add 192.0.2.1/30 dev wan
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # add ports to bridge
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+
+ # configure the bridge
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge
+ ip link set dev br0 up
+
+.. _dsa-vlan-configuration:
+
+Configuration without tagging support
+-------------------------------------
+
+A minority of switches are not capable to use a taging protocol
+(DSA_TAG_PROTO_NONE). These switches can be configured by a VLAN based
+configuration.
+
+single port
+~~~~~~~~~~~
+The configuration can only be set up via VLAN tagging and bridge setup.
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+ ip link add link eth0 name eth0.2 type vlan id 2
+ ip link add link eth0 name eth0.3 type vlan id 3
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+ ip link set eth0.2 up
+ ip link set eth0.3 up
+
+ # bring up the slave interfaces
+ ip link set lan1 up
+ ip link set lan1 up
+ ip link set lan3 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridges
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+ ip link set dev lan3 master br0
+
+ # tag traffic on ports
+ bridge vlan add dev lan1 vid 1 pvid untagged
+ bridge vlan add dev lan2 vid 2 pvid untagged
+ bridge vlan add dev lan3 vid 3 pvid untagged
+
+ # configure the VLANs
+ ip addr add 192.0.2.1/30 dev eth0.1
+ ip addr add 192.0.2.5/30 dev eth0.2
+ ip addr add 192.0.2.9/30 dev eth0.3
+
+ # bring up the bridge devices
+ ip link set br0 up
+
+
+bridge
+~~~~~~
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+
+ # bring up the slave interfaces
+ ip link set lan1 up
+ ip link set lan2 up
+ ip link set lan3 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridge
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+ ip link set dev lan3 master br0
+ ip link set eth0.1 master br0
+
+ # tag traffic on ports
+ bridge vlan add dev lan1 vid 1 pvid untagged
+ bridge vlan add dev lan2 vid 1 pvid untagged
+ bridge vlan add dev lan3 vid 1 pvid untagged
+
+ # configure the bridge
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge
+ ip link set dev br0 up
+
+gateway
+~~~~~~~
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+ ip link add link eth0 name eth0.2 type vlan id 2
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+ ip link set eth0.2 up
+
+ # bring up the slave interfaces
+ ip link set wan up
+ ip link set lan1 up
+ ip link set lan2 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridges
+ ip link set dev wan master br0
+ ip link set eth0.1 master br0
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+
+ # tag traffic on ports
+ bridge vlan add dev lan1 vid 1 pvid untagged
+ bridge vlan add dev lan2 vid 1 pvid untagged
+ bridge vlan add dev wan vid 2 pvid untagged
+
+ # configure the VLANs
+ ip addr add 192.0.2.1/30 dev eth0.2
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge devices
+ ip link set br0 up
diff --git a/Documentation/networking/dsa/index.rst b/Documentation/networking/dsa/index.rst
index 0e5b7a9be406..c279cfbf9083 100644
--- a/Documentation/networking/dsa/index.rst
+++ b/Documentation/networking/dsa/index.rst
@@ -9,3 +9,4 @@ Distributed Switch Architecture
bcm_sf2
lan9303
sja1105
+ configuration
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH v3 2/2] Documentation: net: dsa: b53: Describe b53 configuration
2019-07-05 9:57 [PATCH v3 0/2] Document the configuration of b53 Benedikt Spranger
2019-07-05 9:57 ` [PATCH v3 1/2] Documentation: net: dsa: Describe DSA switch configuration Benedikt Spranger
@ 2019-07-05 9:57 ` Benedikt Spranger
2019-07-05 15:41 ` Florian Fainelli
2019-07-08 22:30 ` [PATCH v3 0/2] Document the configuration of b53 David Miller
2 siblings, 1 reply; 6+ messages in thread
From: Benedikt Spranger @ 2019-07-05 9:57 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Sebastian Andrzej Siewior, Kurt Kanzenbach, Andrew Lunn,
Vivien Didelot
Document the different needs of documentation for the b53 driver.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
---
Documentation/networking/dsa/b53.rst | 183 +++++++++++++++++++++++++
Documentation/networking/dsa/index.rst | 1 +
2 files changed, 184 insertions(+)
create mode 100644 Documentation/networking/dsa/b53.rst
diff --git a/Documentation/networking/dsa/b53.rst b/Documentation/networking/dsa/b53.rst
new file mode 100644
index 000000000000..b41637cdb82b
--- /dev/null
+++ b/Documentation/networking/dsa/b53.rst
@@ -0,0 +1,183 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==========================================
+Broadcom RoboSwitch Ethernet switch driver
+==========================================
+
+The Broadcom RoboSwitch Ethernet switch family is used in quite a range of
+xDSL router, cable modems and other multimedia devices.
+
+The actual implementation supports the devices BCM5325E, BCM5365, BCM539x,
+BCM53115 and BCM53125 as well as BCM63XX.
+
+Implementation details
+======================
+
+The driver is located in ``drivers/net/dsa/b53/`` and is implemented as a
+DSA driver; see ``Documentation/networking/dsa/dsa.rst`` for details on the
+subsystem and what it provides.
+
+The switch is, if possible, configured to enable a Broadcom specific 4-bytes
+switch tag which gets inserted by the switch for every packet forwarded to the
+CPU interface, conversely, the CPU network interface should insert a similar
+tag for packets entering the CPU port. The tag format is described in
+``net/dsa/tag_brcm.c``.
+
+The configuration of the device depends on whether or not tagging is
+supported.
+
+The interface names and example network configuration are used according the
+configuration described in the :ref:`dsa-config-showcases`.
+
+Configuration with tagging support
+----------------------------------
+
+The tagging based configuration is desired. It is not specific to the b53
+DSA driver and will work like all DSA drivers which supports tagging.
+
+See :ref:`dsa-tagged-configuration`.
+
+Configuration without tagging support
+-------------------------------------
+
+Older models (5325, 5365) support a different tag format that is not supported
+yet. 539x and 531x5 require managed mode and some special handling, which is
+also not yet supported. The tagging support is disabled in these cases and the
+switch need a different configuration.
+
+The configuration slightly differ from the :ref:`dsa-vlan-configuration`.
+
+The b53 tags the CPU port in all VLANs, since otherwise any PVID untagged
+VLAN programming would basically change the CPU port's default PVID and make
+it untagged, undesirable.
+
+In difference to the configuration described in :ref:`dsa-vlan-configuration`
+the default VLAN 1 has to be removed from the slave interface configuration in
+single port and gateway configuration, while there is no need to add an extra
+VLAN configuration in the bridge showcase.
+
+single port
+~~~~~~~~~~~
+The configuration can only be set up via VLAN tagging and bridge setup.
+By default packages are tagged with vid 1:
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+ ip link add link eth0 name eth0.2 type vlan id 2
+ ip link add link eth0 name eth0.3 type vlan id 3
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+ ip link set eth0.2 up
+ ip link set eth0.3 up
+
+ # bring up the slave interfaces
+ ip link set wan up
+ ip link set lan1 up
+ ip link set lan2 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridges
+ ip link set dev wan master br0
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+
+ # tag traffic on ports
+ bridge vlan add dev lan1 vid 2 pvid untagged
+ bridge vlan del dev lan1 vid 1
+ bridge vlan add dev lan2 vid 3 pvid untagged
+ bridge vlan del dev lan2 vid 1
+
+ # configure the VLANs
+ ip addr add 192.0.2.1/30 dev eth0.1
+ ip addr add 192.0.2.5/30 dev eth0.2
+ ip addr add 192.0.2.9/30 dev eth0.3
+
+ # bring up the bridge devices
+ ip link set br0 up
+
+
+bridge
+~~~~~~
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+
+ # bring up the slave interfaces
+ ip link set wan up
+ ip link set lan1 up
+ ip link set lan2 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridge
+ ip link set dev wan master br0
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+ ip link set eth0.1 master br0
+
+ # configure the bridge
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge
+ ip link set dev br0 up
+
+gateway
+~~~~~~~
+
+.. code-block:: sh
+
+ # tag traffic on CPU port
+ ip link add link eth0 name eth0.1 type vlan id 1
+ ip link add link eth0 name eth0.2 type vlan id 2
+
+ # The master interface needs to be brought up before the slave ports.
+ ip link set eth0 up
+ ip link set eth0.1 up
+ ip link set eth0.2 up
+
+ # bring up the slave interfaces
+ ip link set wan up
+ ip link set lan1 up
+ ip link set lan2 up
+
+ # create bridge
+ ip link add name br0 type bridge
+
+ # activate VLAN filtering
+ ip link set dev br0 type bridge vlan_filtering 1
+
+ # add ports to bridges
+ ip link set dev wan master br0
+ ip link set eth0.1 master br0
+ ip link set dev lan1 master br0
+ ip link set dev lan2 master br0
+
+ # tag traffic on ports
+ bridge vlan add dev wan vid 2 pvid untagged
+ bridge vlan del dev wan vid 1
+
+ # configure the VLANs
+ ip addr add 192.0.2.1/30 dev eth0.2
+ ip addr add 192.0.2.129/25 dev br0
+
+ # bring up the bridge devices
+ ip link set br0 up
diff --git a/Documentation/networking/dsa/index.rst b/Documentation/networking/dsa/index.rst
index c279cfbf9083..ee631e2d646f 100644
--- a/Documentation/networking/dsa/index.rst
+++ b/Documentation/networking/dsa/index.rst
@@ -6,6 +6,7 @@ Distributed Switch Architecture
:maxdepth: 1
dsa
+ b53
bcm_sf2
lan9303
sja1105
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread