Re: [PATCH 4/5] docs: fix repeated prepositions across documentation

[Randy Dunlap <rdunlap@infradead.org>]

On 5/8/26 10:23 AM, Shuah Khan wrote:
> On 5/8/26 10:38, Adrien Reynard wrote:
> 
> Missing commit log
> 
>> Signed-off-by: Adrien Reynard <reynard.adrien.08@gmail.com>
>> ---
>>   Documentation/dev-tools/kasan.rst                   | 2 +-
>>   Documentation/networking/switchdev.rst              | 2 +-
>>   Documentation/virt/uml/user_mode_linux_howto_v2.rst | 2 +-
>>   3 files changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/dev-tools/kasan.rst b/Documentation/dev-tools/kasan.rst
>> index 4968b2aa60c8..3a8bd40ad905 100644
>> --- a/Documentation/dev-tools/kasan.rst
>> +++ b/Documentation/dev-tools/kasan.rst
>> @@ -392,7 +392,7 @@ reserved to tag freed memory regions.
>>   If the hardware does not support MTE (pre ARMv8.5), Hardware Tag-Based KASAN
>>   will not be enabled. In this case, all KASAN boot parameters are ignored.
>>   -Note that enabling CONFIG_KASAN_HW_TAGS always results in in-kernel TBI being
>> +Note that enabling CONFIG_KASAN_HW_TAGS always results in-kernel TBI being
> 
> This is correct the way it is - no need to change this. "results in in-kernel"

ack.

>>   enabled. Even when ``kasan.mode=off`` is provided or when the hardware does not
>>   support MTE (but supports TBI).
>>   diff --git a/Documentation/networking/switchdev.rst b/Documentation/networking/switchdev.rst
>> index 2966b7122f05..948bce44ca9b 100644
>> --- a/Documentation/networking/switchdev.rst
>> +++ b/Documentation/networking/switchdev.rst
>> @@ -162,7 +162,7 @@ The switchdev driver can know a particular port's position in the topology by
>>   monitoring NETDEV_CHANGEUPPER notifications.  For example, a port moved into a
>>   bond will see its upper master change.  If that bond is moved into a bridge,
>>   the bond's upper master will change.  And so on.  The driver will track such
>> -movements to know what position a port is in in the overall topology by
>> +movements to know what position a port is in the overall topology by
> 
> This looks fine.

Change not needed.

>>   registering for netdevice events and acting on NETDEV_CHANGEUPPER.
>>     L2 Forwarding Offload
>> diff --git a/Documentation/virt/uml/user_mode_linux_howto_v2.rst b/Documentation/virt/uml/user_mode_linux_howto_v2.rst
>> index c37e8e594d12..7b08738c30aa 100644
>> --- a/Documentation/virt/uml/user_mode_linux_howto_v2.rst
>> +++ b/Documentation/virt/uml/user_mode_linux_howto_v2.rst
>> @@ -1092,7 +1092,7 @@ be formatted as plain text.
>>     Developing always goes hand in hand with debugging. First of all,
>>   you can always run UML under gdb and there will be a whole section
>> -later on on how to do that. That, however, is not the only way to
>> +later on how to do that. That, however, is not the only way to
> 
> This change is not needed. If at all add a comma after "later" to make
> a distinction between the use two back to back "on"s
> 
>  "later on,"

We disagree. :)
This change LGTM.

-- 
~Randy