From: Baruch Siach <baruch@tkos.co.il>
To: Andrew Lunn <andrew@lunn.ch>, Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org, Denis Odintsov <d.odintsov@traviangames.com>
Subject: [BUG] mv88e6xxx: tx regression in v5.3
Date: Wed, 11 Dec 2019 11:48:57 +0200 [thread overview]
Message-ID: <87tv67tcom.fsf@tarshish> (raw)
Hi Andrew, Vivien,
Since kernel v5.3 (tested v5.3.15), the 88E6141 switch on SolidRun
Clearfog GT-8K stopped transmitting packets on switch connected
ports. Kernel v5.2 works fine (tested v5.2.21).
Here are the relevant kernel v5.3 log lines:
[ 2.867424] mv88e6085 f412a200.mdio-mii:04: switch 0x3400 detected: Marvell 88E6141, revision 0
[ 2.927445] libphy: mdio: probed
[ 3.578496] mv88e6085 f412a200.mdio-mii:04 lan2 (uninitialized): PHY [!cp1!config-space@f4000000!mdio@12a200!switch0@4!mdio:11] driver [Marvell 88E6390]
[ 3.595674] mv88e6085 f412a200.mdio-mii:04 lan1 (uninitialized): PHY [!cp1!config-space@f4000000!mdio@12a200!switch0@4!mdio:12] driver [Marvell 88E6390]
[ 3.612797] mv88e6085 f412a200.mdio-mii:04 lan4 (uninitialized): PHY [!cp1!config-space@f4000000!mdio@12a200!switch0@4!mdio:13] driver [Marvell 88E6390]
[ 3.629910] mv88e6085 f412a200.mdio-mii:04 lan3 (uninitialized): PHY [!cp1!config-space@f4000000!mdio@12a200!switch0@4!mdio:14] driver [Marvell 88E6390]
[ 3.646049] mv88e6085 f412a200.mdio-mii:04: configuring for phy/ link mode
[ 3.654451] DSA: tree 0 setup
...
[ 10.784521] mvpp2 f4000000.ethernet eth2: configuring for fixed/2500base-x link mode
[ 10.792401] mvpp2 f4000000.ethernet eth2: Link is Up - 2.5Gbps/Full - flow control off
[ 19.817981] mv88e6085 f412a200.mdio-mii:04 lan1: configuring for phy/ link mode
[ 19.827083] 8021q: adding VLAN 0 to HW filter on device lan1
[ 21.577276] mv88e6085 f412a200.mdio-mii:04 lan1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 21.586030] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
The Tx count on the lan1 interface increments, but the ARP packets don't
show on the network.
Do you have any idea?
Thanks,
baruch
--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -
next reply other threads:[~2019-12-11 9:55 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-11 9:48 Baruch Siach [this message]
2019-12-11 13:11 ` [BUG] mv88e6xxx: tx regression in v5.3 Andrew Lunn
2019-12-11 17:07 ` Baruch Siach
2019-12-11 17:49 ` Andrew Lunn
2019-12-12 8:50 ` Baruch Siach
2019-12-12 13:14 ` Andrew Lunn
2019-12-12 14:19 ` Andreas Tobler
2019-12-12 15:08 ` Baruch Siach
2019-12-12 15:13 ` Andrew Lunn
2019-12-12 15:23 ` Baruch Siach
2019-12-12 18:17 ` Baruch Siach
2019-12-12 18:32 ` Marek Behun
2019-12-12 18:48 ` Baruch Siach
2019-12-12 18:36 ` Marek Behun
2019-12-12 19:06 ` Baruch Siach
2019-12-12 19:31 ` Andrew Lunn
2019-12-12 19:41 ` Marek Behun
2019-12-12 20:49 ` Andrew Lunn
2019-12-15 10:13 ` Baruch Siach
2019-12-15 11:10 ` Baruch Siach
2019-12-15 14:53 ` Andrew Lunn
2019-12-15 15:08 ` Baruch Siach
2019-12-15 16:14 ` Andrew Lunn
2019-12-17 18:26 ` Baruch Siach
2019-12-18 14:30 ` Marek Behún
2019-12-18 16:04 ` Baruch Siach
2019-12-19 9:04 ` Baruch Siach
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87tv67tcom.fsf@tarshish \
--to=baruch@tkos.co.il \
--cc=andrew@lunn.ch \
--cc=d.odintsov@traviangames.com \
--cc=netdev@vger.kernel.org \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).