* e1000e crash with 82574L 2.6.37-0.rc5
@ 2010-12-18 18:12 Brian Neu
2010-12-20 17:24 ` Wyborny, Carolyn
0 siblings, 1 reply; 4+ messages in thread
From: Brian Neu @ 2010-12-18 18:12 UTC (permalink / raw)
To: netdev
Is this a known bug?
Any fix out there?
[162536.704103] WARNING: at net/sched/sch_generic.c:258
dev_watchdog+0x111/0x185() [162536.704110] Hardware name: H8SGL
[162536.704116] NETDEV WATCHDOG: eth0 (e1000e): transmit queue 0 timed out
[162536.704122] Modules linked in: ip6table_filter ebtable_nat ebtables
act_police cls_flow cls_fw cls_u32 sch_htb sch_hfsc sch_ingress sch_sfq bridge
stp llc xt_time xt_connlimit xt_realm iptable_raw xt_comment xt_recent
xt_policy ipt_ULOG ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE ipt_ECN ipt_ecn
ipt_CLUSTERIP ipt_ah ipt_addrtype nf_nat_tftp nf_nat_snmp_basic nf_nat_sip
nf_nat_pptp nf_nat_proto_gre nf_nat_irc nf_nat_h323 nf_nat_ftp nf_nat_amanda
ts_kmp nf_conntrack_amanda nf_conntrack_sane nf_conntrack_tftp nf_conntrack_sip
nf_conntrack_proto_sctp nf_conntrack_pptp nf_conntrack_proto_gre
nf_conntrack_netlink nf_conntrack_netbios_ns nf_conntrack_irc nf_conntrack_h323
nf_conntrack_ftp xt_TPROXY nf_tproxy_core ip6_tables nf_defrag_ipv6 xt_tcpmss
xt_pkttype xt_physdev xt_owner xt_NFQUEUE xt_NFLOG nfnetlink_log xt_multiport
xt_mark xt_mac xt_limit xt_length xt_iprange xt_helper xt_hashlimit xt_DSCP
xt_dscp xt_dccp xt_connmark xt_CLASSIFY ipt_LOG iptable_nat nf_nat
iptable_mangle nfnetlink fuse tun sunrpc cpufreq_ondemand powernow_k8
freq_table mperf ipv6 kvm_amd kvm uinput amd64_edac_mod edac_core e1000e
edac_mce_amd i2c_piix4 i2c_core k10temp ghes hed joydev microcode btrfs
zlib_deflate libcrc32c raid1 pata_acpi ata_generic sata_promise pata_atiixp
sata_sil24 uas usb_storage [last unloaded: scsi_wait_scan] [162536.704368]
Pid: 0, comm: kworker/0:0 Not tainted 2.6.37-0.rc5.git2.1.fc13.x86_64 #1
[162536.704375] Call Trace: [162536.704380] <IRQ> [<ffffffff81052e29>]
warn_slowpath_common+0x85/0x9d [162536.704406] [<ffffffff81052ee4>]
warn_slowpath_fmt+0x46/0x48 [162536.704418] [<ffffffff81419f70>]
dev_watchdog+0x111/0x185 [162536.704430] [<ffffffff8105fdcf>]
run_timer_softirq+0x246/0x33f [162536.704441] [<ffffffff8105fd29>] ?
run_timer_softirq+0x1a0/0x33f [162536.704452] [<ffffffff81419e5f>] ?
dev_watchdog+0x0/0x185 [162536.704463] [<ffffffff81059746>]
__do_softirq+0x101/0x20c [162536.704474] [<ffffffff81011aa6>] ?
native_sched_clock+0x2d/0x5f [162536.704484] [<ffffffff8100bc1c>]
call_softirq+0x1c/0x30 [162536.704493] [<ffffffff8100d29f>]
do_softirq+0x4b/0xa3 [162536.704502] [<ffffffff81059480>] irq_exit+0x57/0x9b
[162536.704514] [<ffffffff814bf93c>] smp_apic_timer_interrupt+0x8d/0x9b
[162536.704523] [<ffffffff8100b6d3>] apic_timer_interrupt+0x13/0x20
[162536.704529] <EOI> [<ffffffff81012686>] ? default_idle+0x3e/0x65
[162536.704549] [<ffffffff8102d159>] ? native_safe_halt+0xb/0xd
[162536.704560] [<ffffffff810816ee>] ? trace_hardirqs_on+0xd/0xf
[162536.704571] [<ffffffff8101268b>] default_idle+0x43/0x65 [162536.704581]
[<ffffffff81009c81>] cpu_idle+0xbe/0x132 [162536.704592] [<ffffffff814af9ea>]
start_secondary+0x242/0x244
^ permalink raw reply [flat|nested] 4+ messages in thread
* RE: e1000e crash with 82574L 2.6.37-0.rc5
2010-12-18 18:12 e1000e crash with 82574L 2.6.37-0.rc5 Brian Neu
@ 2010-12-20 17:24 ` Wyborny, Carolyn
2010-12-21 1:20 ` Brian Neu
0 siblings, 1 reply; 4+ messages in thread
From: Wyborny, Carolyn @ 2010-12-20 17:24 UTC (permalink / raw)
To: Brian Neu, netdev@vger.kernel.org; +Cc: e1000-devel@lists.sourceforge.net
>-----Original Message-----
>From: netdev-owner@vger.kernel.org [mailto:netdev-owner@vger.kernel.org]
>On Behalf Of Brian Neu
>Sent: Saturday, December 18, 2010 10:13 AM
>To: netdev@vger.kernel.org
>Subject: e1000e crash with 82574L 2.6.37-0.rc5
>
>Is this a known bug?
>Any fix out there?
>
>[162536.704103] WARNING: at net/sched/sch_generic.c:258
>dev_watchdog+0x111/0x185() [162536.704110] Hardware name: H8SGL
>[162536.704116] NETDEV WATCHDOG: eth0 (e1000e): transmit queue 0 timed
>out
>[162536.704122] Modules linked in: ip6table_filter ebtable_nat ebtables
>act_police cls_flow cls_fw cls_u32 sch_htb sch_hfsc sch_ingress sch_sfq
>bridge
>stp llc xt_time xt_connlimit xt_realm iptable_raw xt_comment xt_recent
>xt_policy ipt_ULOG ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE ipt_ECN
>ipt_ecn
>ipt_CLUSTERIP ipt_ah ipt_addrtype nf_nat_tftp nf_nat_snmp_basic
>nf_nat_sip
>nf_nat_pptp nf_nat_proto_gre nf_nat_irc nf_nat_h323 nf_nat_ftp
>nf_nat_amanda
>ts_kmp nf_conntrack_amanda nf_conntrack_sane nf_conntrack_tftp
>nf_conntrack_sip
>nf_conntrack_proto_sctp nf_conntrack_pptp nf_conntrack_proto_gre
>nf_conntrack_netlink nf_conntrack_netbios_ns nf_conntrack_irc
>nf_conntrack_h323
>nf_conntrack_ftp xt_TPROXY nf_tproxy_core ip6_tables nf_defrag_ipv6
>xt_tcpmss
>xt_pkttype xt_physdev xt_owner xt_NFQUEUE xt_NFLOG nfnetlink_log
>xt_multiport
>xt_mark xt_mac xt_limit xt_length xt_iprange xt_helper xt_hashlimit
>xt_DSCP
>xt_dscp xt_dccp xt_connmark xt_CLASSIFY ipt_LOG iptable_nat nf_nat
>iptable_mangle nfnetlink fuse tun sunrpc cpufreq_ondemand powernow_k8
>freq_table mperf ipv6 kvm_amd kvm uinput amd64_edac_mod edac_core
>e1000e
>edac_mce_amd i2c_piix4 i2c_core k10temp ghes hed joydev microcode btrfs
>zlib_deflate libcrc32c raid1 pata_acpi ata_generic sata_promise
>pata_atiixp
>sata_sil24 uas usb_storage [last unloaded: scsi_wait_scan]
>[162536.704368]
>Pid: 0, comm: kworker/0:0 Not tainted 2.6.37-0.rc5.git2.1.fc13.x86_64
>#1
>[162536.704375] Call Trace: [162536.704380] <IRQ>
>[<ffffffff81052e29>]
>warn_slowpath_common+0x85/0x9d [162536.704406] [<ffffffff81052ee4>]
>warn_slowpath_fmt+0x46/0x48 [162536.704418] [<ffffffff81419f70>]
>dev_watchdog+0x111/0x185 [162536.704430] [<ffffffff8105fdcf>]
>run_timer_softirq+0x246/0x33f [162536.704441] [<ffffffff8105fd29>] ?
>run_timer_softirq+0x1a0/0x33f [162536.704452] [<ffffffff81419e5f>] ?
>dev_watchdog+0x0/0x185 [162536.704463] [<ffffffff81059746>]
>__do_softirq+0x101/0x20c [162536.704474] [<ffffffff81011aa6>] ?
>native_sched_clock+0x2d/0x5f [162536.704484] [<ffffffff8100bc1c>]
>call_softirq+0x1c/0x30 [162536.704493] [<ffffffff8100d29f>]
>do_softirq+0x4b/0xa3 [162536.704502] [<ffffffff81059480>]
>irq_exit+0x57/0x9b
>[162536.704514] [<ffffffff814bf93c>] smp_apic_timer_interrupt+0x8d/0x9b
>[162536.704523] [<ffffffff8100b6d3>] apic_timer_interrupt+0x13/0x20
>[162536.704529] <EOI> [<ffffffff81012686>] ? default_idle+0x3e/0x65
>[162536.704549] [<ffffffff8102d159>] ? native_safe_halt+0xb/0xd
>[162536.704560] [<ffffffff810816ee>] ? trace_hardirqs_on+0xd/0xf
>[162536.704571] [<ffffffff8101268b>] default_idle+0x43/0x65
>[162536.704581]
>[<ffffffff81009c81>] cpu_idle+0xbe/0x132 [162536.704592]
>[<ffffffff814af9ea>]
>start_secondary+0x242/0x244
>
>--
>To unsubscribe from this list: send the line "unsubscribe netdev" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello,
We have some known issues with 82574L but most have been resolved in the latest versions, so I'll need some more information.
What version of e1000e are you using exactly? Are you able to download and test the latest version of the driver from SourceForge?
Please open an issue at SourceForge.net for easier tracking of debugging information.
Please provide an output of lspci -vvv.
What hw platform is this happening on? How often does it happen and how long does it take to happen after reset or reboot? Is ASPM enabled or disabled on your system. Its possible to disable this in the BIOS, but not all BIOS provide the option. If its enabled for some reason, please disable it and try the driver again.
Thanks,
Carolyn
Carolyn Wyborny
Linux Development
LAN Access Division
Intel Corporation
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: e1000e crash with 82574L 2.6.37-0.rc5
2010-12-20 17:24 ` Wyborny, Carolyn
@ 2010-12-21 1:20 ` Brian Neu
2010-12-21 18:13 ` Wyborny, Carolyn
0 siblings, 1 reply; 4+ messages in thread
From: Brian Neu @ 2010-12-21 1:20 UTC (permalink / raw)
To: Wyborny, Carolyn, netdev@vger.kernel.org
Cc: e1000-devel@lists.sourceforge.net
[-- Attachment #1: Type: text/plain, Size: 1381 bytes --]
> Hello,
Thanks for responding. I really wasn't sure where to report this.
> We have some known issues with 82574L but most have been resolved in the
>latest versions, so I'll need some more information.
>
> What version of e1000e are you using exactly? Are you able to download and
>test the latest version of the driver from SourceForge?
This is the fedora build of kernel 2.6.37.0.rc5 which I downloaded from
koji.fedoraproject.org. I'm not sure which version of e1000e is included, but
if I need to build a new module, just let me know.
I had opened a bugzilla report with redhat which also has more backtraces:
https://bugzilla.redhat.com/show_bug.cgi?id=625776
> Please open an issue at SourceForge.net for easier tracking of debugging
>information.
>
> Please provide an output of lspci -vvv.
Attached.
> What hw platform is this happening on?
It's a Supermicro MB for AMD Socket G34
> How often does it happen and how long does it take to happen after reset or
>reboot?
It usually doesn't happen unless the system has been running for hours or days.
>Is ASPM enabled or disabled on your system. Its possible to disable this in
>the BIOS, but not all BIOS provide the option. If its enabled for some reason,
>please disable it and try the driver again.
I'm going to check on this very soon and reply to the e1000 list only.
[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 37550 bytes --]
00:00.0 Host bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx0 port A) (rev 02)
Subsystem: Super Micro Computer Inc Device a711
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: [f0] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=20 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: [e]
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [9c] HyperTransport: #1a
Capabilities: [70] MSI: Enable- Count=1/4 Maskable- 64bit-
Address: 00000000 Data: 0000
00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port D) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee10000 Data: 4051
Capabilities: [b0] Subsystem: Super Micro Computer Inc Device a711
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [190 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:09.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x2, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #9, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee10000 Data: 4059
Capabilities: [b0] Subsystem: Super Micro Computer Inc Device a711
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [190 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0a.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x2, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #10, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee10000 Data: 4061
Capabilities: [b0] Subsystem: Super Micro Computer Inc Device a711
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [190 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode] (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at 9000 [size=4]
Region 2: I/O ports at 8000 [size=8]
Region 3: I/O ports at 7000 [size=4]
Region 4: I/O ports at 6000 [size=16]
Region 5: Memory at fe8fa400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Kernel driver in use: ahci
00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe8f6000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe8f7000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe8fa800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe8f8000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe8f9000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: ATI Technologies Inc SB700/SB800 USB EHCI Controller
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe8fac00 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3d)
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: [70] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: pata_atiixp
Kernel modules: ata_generic, pata_acpi, pata_atiixp
00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdf00000-fe7fffff
Prefetchable memory behind bridge: fc000000-fcffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc Device 4396
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8fb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: [e]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [a0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 500MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [c0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [e0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: amd64_edac
Kernel modules: amd64_edac_mod
00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [c0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [e0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [a0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [c0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 500MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: amd64_edac
Kernel modules: amd64_edac_mod
00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
Kernel modules: k10temp
00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=N/C DwFcInEn- LWO=N/C DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
Capabilities: [a0] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 200MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
01:02.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA 300 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC40718 (SATA 300 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at b400 [size=128]
Region 2: I/O ports at b800 [size=256]
Region 3: Memory at fdfaf000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fdfc0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fdfb0000 [disabled] [size=32K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_promise
Kernel modules: sata_promise
01:04.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200eW WPCM450 (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fdffc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at c800 [size=32]
Region 3: Memory at fe9dc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-30-48-ff-ff-f5-02-82
Kernel driver in use: e1000e
Kernel modules: e1000e
03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
Subsystem: Super Micro Computer Inc Device a711
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feae0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d800 [size=32]
Region 3: Memory at feadc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-30-48-ff-ff-f5-02-83
Kernel driver in use: e1000e
Kernel modules: e1000e
04:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
Subsystem: Silicon Image, Inc. Device 7132
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feb7bc00 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at feb7c000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at e800 [size=128]
Expansion ROM at feb80000 [disabled] [size=512K]
Capabilities: [54] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: sata_sil24
Kernel modules: sata_sil24
^ permalink raw reply [flat|nested] 4+ messages in thread
* RE: e1000e crash with 82574L 2.6.37-0.rc5
2010-12-21 1:20 ` Brian Neu
@ 2010-12-21 18:13 ` Wyborny, Carolyn
0 siblings, 0 replies; 4+ messages in thread
From: Wyborny, Carolyn @ 2010-12-21 18:13 UTC (permalink / raw)
To: Brian Neu, netdev@vger.kernel.org; +Cc: e1000-devel@lists.sourceforge.net
>-----Original Message-----
>From: Brian Neu [mailto:proclivity76@yahoo.com]
>Sent: Monday, December 20, 2010 5:20 PM
>To: Wyborny, Carolyn; netdev@vger.kernel.org
>Cc: e1000-devel@lists.sourceforge.net
>Subject: Re: e1000e crash with 82574L 2.6.37-0.rc5
>
>> Hello,
>
>
>Thanks for responding. I really wasn't sure where to report this.
>
>> We have some known issues with 82574L but most have been resolved in
>the
>>latest versions, so I'll need some more information.
>>
>> What version of e1000e are you using exactly? Are you able to
>download and
>>test the latest version of the driver from SourceForge?
>
>
>This is the fedora build of kernel 2.6.37.0.rc5 which I downloaded from
>koji.fedoraproject.org. I'm not sure which version of e1000e is
>included, but
>if I need to build a new module, just let me know.
>
>I had opened a bugzilla report with redhat which also has more
>backtraces:
> https://bugzilla.redhat.com/show_bug.cgi?id=625776
>
>> Please open an issue at SourceForge.net for easier tracking of
>debugging
>>information.
>>
>> Please provide an output of lspci -vvv.
>
>
>Attached.
>
>> What hw platform is this happening on?
>
>It's a Supermicro MB for AMD Socket G34
>
>> How often does it happen and how long does it take to happen after
>reset or
>>reboot?
>
>It usually doesn't happen unless the system has been running for hours
>or days.
>
>>Is ASPM enabled or disabled on your system. Its possible to disable
>this in
>>the BIOS, but not all BIOS provide the option. If its enabled for
>some reason,
>>please disable it and try the driver again.
>
>
>I'm going to check on this very soon and reply to the e1000 list only.
Hello Brian,
With this being a variant of Fedora, filing a Bugzilla was the right thing to do. I missed that in your first email.
I checked your lspci output and ASPM *is* disabled as it should be.
When the adapter crashes/resets (per the log) does it come back up or stay down?
Since you're downloading off the Fedora build site, you could be encountering any number of things as these are live untested builds at this point.
Can you download a vanilla upstream build from kernel.org complete and see if the problem is happening there? Or, you can download the latest released Fedora 14 from fedoraproject.org and see if the problem is happening with that build.
Let me know how it goes,
Thanks,
Carolyn
Carolyn Wyborny
Linux Development
LAN Access Division
Intel Corporation
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-12-21 18:14 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-12-18 18:12 e1000e crash with 82574L 2.6.37-0.rc5 Brian Neu
2010-12-20 17:24 ` Wyborny, Carolyn
2010-12-21 1:20 ` Brian Neu
2010-12-21 18:13 ` Wyborny, Carolyn
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).