Re: Hight speed data sending from custom IP out of kernel

[zhou rui <zhourui.cn@gmail.com>]

On Wed, Apr 20, 2011 at 12:02 AM, juice <juice@swagman.org> wrote:
>
> Hi!
>
> I can see you are probably going to run into CPU performance problems, but
> it depends a lot on the type of traffic you are going to send.
>
> My system requires quite fast processor, but even more important is to
> have a network interface card that really supports the full speed of
> gigabit ethernet line. The reason for that is that my test traffic
> includes streams of very small packets that cause a lot of overhead in
> processing.
>
> Most of my test traffic is UDP, but it does not really matter what the
> higher layers of the traffic are, this scheme operates on the ethernet
> layer and does not care about payload structure.
>
> I tried several NIC:s before i settled using Intel 82576 cards with the
> igb driver. If you have less capable interface card, your small packet
> performance is going to be a lot poorer.
>
> Using that card I can get to full speed GE line rate even with 64byte
> packets, but if you want to send larger packets, say close to 1500byte
> then almost any NIC will work OK for you.
>
> You can download the module code and the userland seeding application from
> my svn server at https://toosa.swagman.org/svn/streamgen
> The streamseed userland application requires libpcap-dev to build
> correctly but the streamgen module is self-sufficent.
>
> There is not a lot of documentation, and the module is still "work in
> progress" as I am going to fix it to work with more than one interface at
> the same time when I get to do it. Currently it can only use one interface
> on the sending host machine.
>
>  - Juice -
>

does it use the same command/config file as pktgen?
or special command?



>
>> Hi Juice,
>>
>> juice wrote:
>>> Hi Michal.
>>>
>>> How fast do you need to send the data?
>>
>> It sounds weird but as fast as possible. There is no specific limit
>> because I
>> want to create demo and test it on various hw configuration which I can
>> easily
>> create on FPGA. For now the bottleneck is Microblaze cpu. It can run from
>> 50MHz
>> till 170-180MHz. We also support both endians and have two hw IP
>> cores(10/100/1000) which I can use.
>>
>>> I have an application where I send test stream out to GE line and can
>>> fill
>>> the total capacity of the ethernet regardless of the packet size.
>>
>> What cpu do you use?
>>
>>>
>>> The test stream I am sending is stored in kernel memory, and therefore
>>> is
>>> limited by the amount of free memory. 200M is no problem.
>>
>> Is it UDP or TCP?
>>
>>>
>>> The solution I am using is loosely based on the pktgen module, except
>>> that
>>> my module can load a wireshark capture from userland program and then
>>> send
>>> it from ethernet interface in wire speed.
>>
>> Sound good. Would it be possible to see it and test it?
>>
>> Thanks,
>> Michal
>>
>>
>>>
>>>   - Juice -
>>>
>>>
>>>> Hi,
>>>> I would like to create demo for high speed data sending from custom IP
>>> through
>>>> the ethernet. I think the best description is that there are dmaable
>>>> memory
>>>> mapped registers or just memory which store data I want to send (for
>>> example 200MB).
>>>> Linux should handle all communication between target(probably server)
>>> and
>>>> host
>>>> (client) but data in the packets should go from that custom IP and
>>>> can't go
>>>> through the kernel because of performance issue.
>>>> Ethernet core have own DMA which I could use but the question is if
>>> there
>>>> is any
>>>> option how to convince the kernel that data will go directly from
>>>> memory
>>> mapped
>>>> registers and the kernel/driver/... just setup dma BD for headers and
>>> second for
>>>> data.
>>>> Do you have any experience with any solution with passing data
>>> completely
>>>> out of
>>>> kernel?
>>>> Thanks,
>>>> Michal
>>>> --
>>>> Michal Simek, Ing. (M.Eng)
>>>> w: www.monstr.eu p: +42-0-721842854
>>>> Maintainer of Linux kernel 2.6 Microblaze Linux -
>>>> http://www.monstr.eu/fdt/
>>>> Microblaze U-BOOT custodian
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>>>> the
>>> body of a message to majordomo@vger.kernel.org
>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>>
>>>
>>>
>>>
>>
>>
>> --
>> Michal Simek, Ing. (M.Eng)
>> w: www.monstr.eu p: +42-0-721842854
>> Maintainer of Linux kernel 2.6 Microblaze Linux -
>> http://www.monstr.eu/fdt/
>> Microblaze U-BOOT custodian
>>
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>