* Re: [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged [not found] <503D486B.1030208@gmail.com> @ 2012-08-29 7:03 ` Stefan Hajnoczi 2012-08-30 12:13 ` ching 0 siblings, 1 reply; 5+ messages in thread From: Stefan Hajnoczi @ 2012-08-29 7:03 UTC (permalink / raw) To: ching; +Cc: qemu-devel, kaber, Michael S. Tsirkin, netdev On Tue, Aug 28, 2012 at 11:38 PM, ching <lsching17@gmail.com> wrote: > Hi all, > > I try to setup guest network with macvlan, as guest cannot communicate with host directly, i try to workaround by configuring host to using a macvlan interface > > host: Gentoo x64, kernel 3.5.2, qemu-kvm 1.1.1-r1, libvirt 0.9.13 > guest: Ubuntu 12.04, kernel 3.4.9, virtio-net > > The host is using macvlan (interface name: znet0, ip: 192.168.1.2, bridge mode) > > The guest is using macvtap managed by libvirt (interface name: macvtap0, ip: 192.168.1.184, bridge mode, with vhost) > > > I am facing a strange problem that the guest/host can communicate only when the network cable of the ethernet adapter is connected. > > > > > The network config of the host > > $ifconfig > > eth0 Link encap:Ethernet HWaddr f4:6d:xx:xx:xx:xx > inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:86507 errors:0 dropped:0 overruns:0 frame:0 > TX packets:55940 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:126005746 (120.1 MiB) TX bytes:4394225 (4.1 MiB) > > macvtap0 Link encap:Ethernet HWaddr 52:54:xx:xx:xx:xx > inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:70 errors:0 dropped:0 overruns:0 frame:0 > TX packets:84 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:500 > RX bytes:9036 (8.8 KiB) TX bytes:14734 (14.3 KiB) > > znet0 Link encap:Ethernet HWaddr 00:60:xx:xx:xx:xx > inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: 2002:xx:xx:xx:xx/64 Scope:Global > inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:4463190 errors:0 dropped:0 overruns:0 frame:0 > TX packets:12527522 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:3959213697 (3.6 GiB) TX bytes:18590336476 (17.3 GiB) > > $ip -d link show > > 10: znet0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT > link/ether 00:60:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff > macvlan mode bridge > 17: macvtap0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 500 > link/ether 52:54:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff > macvtap mode bridge > > libvirt config of the guest network > > <interface type='direct'> > <mac address='52:54:xx:xx:xx:xx'/> > <source dev='eth0' mode='bridge'/> > <model type='virtio'/> > <address type='pci' domain='0x0000' bus='0x00' slot='0x08' function='0x0'/> > </interface> > > The network config of the guest > > eth0 Link encap:Ethernet HWaddr 52:54:xx:xx:xx:xx > inet addr:192.168.1.184 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: 2002:xx:xx:xx:xxx/64 Scope:Global > inet6 addr: 2002:xx:xx:xx:xx/64 Scope:Global > inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:25 errors:0 dropped:0 overruns:0 frame:0 > TX packets:66 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:3108 (3.1 KB) TX bytes:13066 (13.0 KB) > > when network cable of host is plugged in > > $ ping 192.168.1.184 > PING 192.168.1.184 (192.168.1.184) 56(84) bytes of data. > 64 bytes from 192.168.1.184: icmp_req=1 ttl=64 time=0.314 ms > 64 bytes from 192.168.1.184: icmp_req=2 ttl=64 time=0.253 ms > 64 bytes from 192.168.1.184: icmp_req=3 ttl=64 time=0.230 ms > > > Afterward, i unplugged the network cable to ensure that packet is not routed via external router, but the test seems failed. > > $ ping 192.168.1.184 > PING 192.168.1.184 (192.168.1.184) 56(84) bytes of data. > From 192.168.1.2: icmp_seq=10 Destination Host Unreachable > From 192.168.1.2: icmp_seq=11 Destination Host Unreachable > > > Do anyone have similar problem? Am i missing something? Can you try the same test with two macvlan interfaces on the host (no macvtap)? You may need to use the ping -I <interface-address> argument to force the ping source address to a specific macvlan interface. If you see the same problem, it may just be the macvlan design - it is stacked on top of eth0 and might not work when eth0 is down. CCing macvlan/macvtap folks. Stefan ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged 2012-08-29 7:03 ` [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged Stefan Hajnoczi @ 2012-08-30 12:13 ` ching 2012-08-30 12:53 ` Stefan Hajnoczi 0 siblings, 1 reply; 5+ messages in thread From: ching @ 2012-08-30 12:13 UTC (permalink / raw) To: Stefan Hajnoczi; +Cc: qemu-devel, kaber, Michael S. Tsirkin, netdev > Can you try the same test with two macvlan interfaces on the host (no > macvtap)? You may need to use the ping -I <interface-address> > argument to force the ping source address to a specific macvlan > interface. > > If you see the same problem, it may just be the macvlan design - it is > stacked on top of eth0 and might not work when eth0 is down. CCing > macvlan/macvtap folks. > > Stefan > tested as below $ifconfig eth0 Link encap:Ethernet HWaddr f4:6d:xx:xx:xx:xx inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86507 errors:0 dropped:0 overruns:0 frame:0 TX packets:55940 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:126005746 (120.1 MiB) TX bytes:4394225 (4.1 MiB) macvtap0 Link encap:Ethernet HWaddr 52:54:xx:xx:xx:xx inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:70 errors:0 dropped:0 overruns:0 frame:0 TX packets:84 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:9036 (8.8 KiB) TX bytes:14734 (14.3 KiB) znet0 Link encap:Ethernet HWaddr 00:60:xx:xx:xx:92 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: 2002:xx:xx:xx:xx/64 Scope:Global inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4463190 errors:0 dropped:0 overruns:0 frame:0 TX packets:12527522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3959213697 (3.6 GiB) TX bytes:18590336476 (17.3 GiB) znet1 Link encap:Ethernet HWaddr 00:60:xx:xx:xx:99 inet addr:192.168.1.177 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: 2002:xx:xx:xx:xx64 Scope:Global inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1399 (1.3 KiB) TX bytes:1522 (1.4 KiB) $ ip -d link show 10: znet0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT link/ether 00:60:xx:xx:xx:92 brd ff:ff:ff:ff:ff:ff macvlan mode bridge 15: znet1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT link/ether 00:60:xx:xx:xx:99 brd ff:ff:ff:ff:ff:ff macvlan mode bridge the macvlan interface cannot ping each other no matter network cable is plugged or not $ ping -I 192.168.1.2 192.168.1.177 PING 192.168.1.177 (192.168.1.177) from 192.168.1.2 : 56(84) bytes of data. --- 192.168.1.177 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 4999ms I also perform an additional test: the guests (macvtap bridge mode) CAN communicate each other no matter network cable is plugged or not. ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged 2012-08-30 12:13 ` ching @ 2012-08-30 12:53 ` Stefan Hajnoczi 2012-08-30 22:32 ` ching 0 siblings, 1 reply; 5+ messages in thread From: Stefan Hajnoczi @ 2012-08-30 12:53 UTC (permalink / raw) To: ching; +Cc: qemu-devel, kaber, Michael S. Tsirkin, netdev On Thu, Aug 30, 2012 at 1:13 PM, ching <lsching17@gmail.com> wrote: > >> Can you try the same test with two macvlan interfaces on the host (no >> macvtap)? You may need to use the ping -I <interface-address> >> argument to force the ping source address to a specific macvlan >> interface. >> >> If you see the same problem, it may just be the macvlan design - it is >> stacked on top of eth0 and might not work when eth0 is down. CCing >> macvlan/macvtap folks. >> >> Stefan >> > > tested as below > > $ifconfig > > eth0 Link encap:Ethernet HWaddr f4:6d:xx:xx:xx:xx > inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:86507 errors:0 dropped:0 overruns:0 frame:0 > TX packets:55940 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:126005746 (120.1 MiB) TX bytes:4394225 (4.1 MiB) > > macvtap0 Link encap:Ethernet HWaddr 52:54:xx:xx:xx:xx > inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:70 errors:0 dropped:0 overruns:0 frame:0 > TX packets:84 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:500 > RX bytes:9036 (8.8 KiB) TX bytes:14734 (14.3 KiB) > > znet0 Link encap:Ethernet HWaddr 00:60:xx:xx:xx:92 > inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: 2002:xx:xx:xx:xx/64 Scope:Global > inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:4463190 errors:0 dropped:0 overruns:0 frame:0 > TX packets:12527522 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:3959213697 (3.6 GiB) TX bytes:18590336476 (17.3 GiB) > > znet1 Link encap:Ethernet HWaddr 00:60:xx:xx:xx:99 > inet addr:192.168.1.177 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: 2002:xx:xx:xx:xx64 Scope:Global > inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:8 errors:0 dropped:0 overruns:0 frame:0 > TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1399 (1.3 KiB) TX bytes:1522 (1.4 KiB) > > $ ip -d link show > > 10: znet0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT > link/ether 00:60:xx:xx:xx:92 brd ff:ff:ff:ff:ff:ff > macvlan mode bridge > 15: znet1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT > link/ether 00:60:xx:xx:xx:99 brd ff:ff:ff:ff:ff:ff > macvlan mode bridge > > > the macvlan interface cannot ping each other no matter network cable is plugged or not > > $ ping -I 192.168.1.2 192.168.1.177 > PING 192.168.1.177 (192.168.1.177) from 192.168.1.2 : 56(84) bytes of data. > > --- 192.168.1.177 ping statistics --- > 6 packets transmitted, 0 received, 100% packet loss, time 4999ms In bridge mode I expected them to be able to communicate. > I also perform an additional test: the guests (macvtap bridge mode) CAN communicate each other no matter network cable is plugged or not. Strange. I thought the original problem was that the macvtap guests cannot communicate with each other when the network cable is unplugged? Hopefully someone else can help you, I'm not familiar enough with macvlan/macvtap. Stefan ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: macvlan/macvtap: guest/host cannot communicate when network cable is unplugged 2012-08-30 12:53 ` Stefan Hajnoczi @ 2012-08-30 22:32 ` ching 2012-08-31 5:34 ` [Qemu-devel] " Stefan Hajnoczi 0 siblings, 1 reply; 5+ messages in thread From: ching @ 2012-08-30 22:32 UTC (permalink / raw) To: Stefan Hajnoczi; +Cc: netdev, Michael S. Tsirkin, qemu-devel, kaber >> I also perform an additional test: the guests (macvtap bridge mode) CAN communicate each other no matter network cable is plugged or not. > Strange. I thought the original problem was that the macvtap guests > cannot communicate with each other when the network cable is > unplugged? > > Hopefully someone else can help you, I'm not familiar enough with > macvlan/macvtap. > > Stefan > My word may be a little bit confusing, it should be I also perform an additional test: I created two qemu guests (macvtap bridge mode on eth0), they CAN communicate each other no matter network cable of the host is unplugged or not. and my problem is specified in the subject already: guest/host cannot communicate when network cable is unplugged if my configuration seems correct, i may file a kernel bugzilla and seek for their advice. ching ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged 2012-08-30 22:32 ` ching @ 2012-08-31 5:34 ` Stefan Hajnoczi 0 siblings, 0 replies; 5+ messages in thread From: Stefan Hajnoczi @ 2012-08-31 5:34 UTC (permalink / raw) To: ching; +Cc: qemu-devel, kaber, Michael S. Tsirkin, netdev On Thu, Aug 30, 2012 at 11:32 PM, ching <lsching17@gmail.com> wrote: > >>> I also perform an additional test: the guests (macvtap bridge mode) CAN communicate each other no matter network cable is plugged or not. >> Strange. I thought the original problem was that the macvtap guests >> cannot communicate with each other when the network cable is >> unplugged? >> >> Hopefully someone else can help you, I'm not familiar enough with >> macvlan/macvtap. >> >> Stefan >> > > My word may be a little bit confusing, it should be > > I also perform an additional test: I created two qemu guests (macvtap bridge mode on eth0), they CAN communicate each other no matter network cable of the host is unplugged or not. > > and my problem is specified in the subject already: guest/host cannot communicate when network cable is unplugged > > > if my configuration seems correct, i may file a kernel bugzilla and seek for their advice. Yes. If no one else responds then it's worth filing a bug. Stefan ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-08-31 5:34 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <503D486B.1030208@gmail.com>
2012-08-29 7:03 ` [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged Stefan Hajnoczi
2012-08-30 12:13 ` ching
2012-08-30 12:53 ` Stefan Hajnoczi
2012-08-30 22:32 ` ching
2012-08-31 5:34 ` [Qemu-devel] " Stefan Hajnoczi
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).