From: Russell King <rmk+kernel@armlinux.org.uk>
To: Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>, netdev@vger.kernel.org
Subject: [PATCH net-next 09/14] net: phylink: split link_an_mode configured and current settings
Date: Mon, 09 Dec 2019 14:07:27 +0000 [thread overview]
Message-ID: <E1ieJh9-0004P8-St@rmk-PC.armlinux.org.uk> (raw)
In-Reply-To: <20191209140258.GI25745@shell.armlinux.org.uk>
Split link_an_mode between the configured setting and the current
operating setting. This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
drivers/net/phy/phylink.c | 59 ++++++++++++++++++++-------------------
1 file changed, 31 insertions(+), 28 deletions(-)
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 056ee50aa556..035fdc187d3c 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -48,7 +48,8 @@ struct phylink {
unsigned long phylink_disable_state; /* bitmask of disables */
struct phy_device *phydev;
phy_interface_t link_interface; /* PHY_INTERFACE_xxx */
- u8 link_an_mode; /* MLO_AN_xxx */
+ u8 cfg_link_an_mode; /* MLO_AN_xxx */
+ u8 cur_link_an_mode;
u8 link_port; /* The current non-phy ethtool port */
__ETHTOOL_DECLARE_LINK_MODE_MASK(supported);
@@ -256,12 +257,12 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
dn = fwnode_get_named_child_node(fwnode, "fixed-link");
if (dn || fwnode_property_present(fwnode, "fixed-link"))
- pl->link_an_mode = MLO_AN_FIXED;
+ pl->cfg_link_an_mode = MLO_AN_FIXED;
fwnode_handle_put(dn);
if (fwnode_property_read_string(fwnode, "managed", &managed) == 0 &&
strcmp(managed, "in-band-status") == 0) {
- if (pl->link_an_mode == MLO_AN_FIXED) {
+ if (pl->cfg_link_an_mode == MLO_AN_FIXED) {
phylink_err(pl,
"can't use both fixed-link and in-band-status\n");
return -EINVAL;
@@ -273,7 +274,7 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
phylink_set(pl->supported, Asym_Pause);
phylink_set(pl->supported, Pause);
pl->link_config.an_enabled = true;
- pl->link_an_mode = MLO_AN_INBAND;
+ pl->cfg_link_an_mode = MLO_AN_INBAND;
switch (pl->link_config.interface) {
case PHY_INTERFACE_MODE_SGMII:
@@ -333,14 +334,14 @@ static void phylink_mac_config(struct phylink *pl,
{
phylink_dbg(pl,
"%s: mode=%s/%s/%s/%s adv=%*pb pause=%02x link=%u an=%u\n",
- __func__, phylink_an_mode_str(pl->link_an_mode),
+ __func__, phylink_an_mode_str(pl->cur_link_an_mode),
phy_modes(state->interface),
phy_speed_to_str(state->speed),
phy_duplex_to_str(state->duplex),
__ETHTOOL_LINK_MODE_MASK_NBITS, state->advertising,
state->pause, state->link, state->an_enabled);
- pl->ops->mac_config(pl->config, pl->link_an_mode, state);
+ pl->ops->mac_config(pl->config, pl->cur_link_an_mode, state);
}
static void phylink_mac_config_up(struct phylink *pl,
@@ -441,7 +442,7 @@ static void phylink_mac_link_up(struct phylink *pl,
struct net_device *ndev = pl->netdev;
pl->cur_interface = link_state.interface;
- pl->ops->mac_link_up(pl->config, pl->link_an_mode,
+ pl->ops->mac_link_up(pl->config, pl->cur_link_an_mode,
pl->phy_state.interface,
pl->phydev);
@@ -461,7 +462,7 @@ static void phylink_mac_link_down(struct phylink *pl)
if (ndev)
netif_carrier_off(ndev);
- pl->ops->mac_link_down(pl->config, pl->link_an_mode,
+ pl->ops->mac_link_down(pl->config, pl->cur_link_an_mode,
pl->cur_interface);
phylink_info(pl, "Link is Down\n");
}
@@ -480,7 +481,7 @@ static void phylink_resolve(struct work_struct *w)
} else if (pl->mac_link_dropped) {
link_state.link = false;
} else {
- switch (pl->link_an_mode) {
+ switch (pl->cur_link_an_mode) {
case MLO_AN_PHY:
link_state = pl->phy_state;
phylink_resolve_flow(pl, &link_state);
@@ -648,7 +649,7 @@ struct phylink *phylink_create(struct phylink_config *config,
return ERR_PTR(ret);
}
- if (pl->link_an_mode == MLO_AN_FIXED) {
+ if (pl->cfg_link_an_mode == MLO_AN_FIXED) {
ret = phylink_parse_fixedlink(pl, fwnode);
if (ret < 0) {
kfree(pl);
@@ -656,6 +657,8 @@ struct phylink *phylink_create(struct phylink_config *config,
}
}
+ pl->cur_link_an_mode = pl->cfg_link_an_mode;
+
ret = phylink_register_sfp(pl, fwnode);
if (ret < 0) {
kfree(pl);
@@ -771,8 +774,8 @@ static int phylink_attach_phy(struct phylink *pl, struct phy_device *phy,
{
int ret;
- if (WARN_ON(pl->link_an_mode == MLO_AN_FIXED ||
- (pl->link_an_mode == MLO_AN_INBAND &&
+ if (WARN_ON(pl->cfg_link_an_mode == MLO_AN_FIXED ||
+ (pl->cfg_link_an_mode == MLO_AN_INBAND &&
phy_interface_mode_is_8023z(interface))))
return -EINVAL;
@@ -839,8 +842,8 @@ int phylink_of_phy_connect(struct phylink *pl, struct device_node *dn,
int ret;
/* Fixed links and 802.3z are handled without needing a PHY */
- if (pl->link_an_mode == MLO_AN_FIXED ||
- (pl->link_an_mode == MLO_AN_INBAND &&
+ if (pl->cfg_link_an_mode == MLO_AN_FIXED ||
+ (pl->cfg_link_an_mode == MLO_AN_INBAND &&
phy_interface_mode_is_8023z(pl->link_interface)))
return 0;
@@ -851,7 +854,7 @@ int phylink_of_phy_connect(struct phylink *pl, struct device_node *dn,
phy_node = of_parse_phandle(dn, "phy-device", 0);
if (!phy_node) {
- if (pl->link_an_mode == MLO_AN_PHY)
+ if (pl->cfg_link_an_mode == MLO_AN_PHY)
return -ENODEV;
return 0;
}
@@ -914,7 +917,7 @@ int phylink_fixed_state_cb(struct phylink *pl,
/* It does not make sense to let the link be overriden unless we use
* MLO_AN_FIXED
*/
- if (pl->link_an_mode != MLO_AN_FIXED)
+ if (pl->cfg_link_an_mode != MLO_AN_FIXED)
return -EINVAL;
mutex_lock(&pl->state_mutex);
@@ -964,7 +967,7 @@ void phylink_start(struct phylink *pl)
ASSERT_RTNL();
phylink_info(pl, "configuring for %s/%s link mode\n",
- phylink_an_mode_str(pl->link_an_mode),
+ phylink_an_mode_str(pl->cur_link_an_mode),
phy_modes(pl->link_config.interface));
/* Always set the carrier off */
@@ -987,7 +990,7 @@ void phylink_start(struct phylink *pl)
clear_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state);
phylink_run_resolve(pl);
- if (pl->link_an_mode == MLO_AN_FIXED && pl->link_gpio) {
+ if (pl->cfg_link_an_mode == MLO_AN_FIXED && pl->link_gpio) {
int irq = gpiod_to_irq(pl->link_gpio);
if (irq > 0) {
@@ -1002,7 +1005,7 @@ void phylink_start(struct phylink *pl)
if (irq <= 0)
mod_timer(&pl->link_poll, jiffies + HZ);
}
- if (pl->link_an_mode == MLO_AN_FIXED && pl->get_fixed_state)
+ if (pl->cfg_link_an_mode == MLO_AN_FIXED && pl->get_fixed_state)
mod_timer(&pl->link_poll, jiffies + HZ);
if (pl->phydev)
phy_start(pl->phydev);
@@ -1129,7 +1132,7 @@ int phylink_ethtool_ksettings_get(struct phylink *pl,
linkmode_copy(kset->link_modes.supported, pl->supported);
- switch (pl->link_an_mode) {
+ switch (pl->cur_link_an_mode) {
case MLO_AN_FIXED:
/* We are using fixed settings. Report these as the
* current link settings - and note that these also
@@ -1201,7 +1204,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
/* If we have a fixed link (as specified by firmware), refuse
* to change link parameters.
*/
- if (pl->link_an_mode == MLO_AN_FIXED &&
+ if (pl->cur_link_an_mode == MLO_AN_FIXED &&
(s->speed != pl->link_config.speed ||
s->duplex != pl->link_config.duplex))
return -EINVAL;
@@ -1213,7 +1216,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
__clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, config.advertising);
} else {
/* If we have a fixed link, refuse to enable autonegotiation */
- if (pl->link_an_mode == MLO_AN_FIXED)
+ if (pl->cur_link_an_mode == MLO_AN_FIXED)
return -EINVAL;
config.speed = SPEED_UNKNOWN;
@@ -1255,7 +1258,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
* configuration. For a fixed link, this isn't able to change any
* parameters, which just leaves inband mode.
*/
- if (pl->link_an_mode == MLO_AN_INBAND &&
+ if (pl->cur_link_an_mode == MLO_AN_INBAND &&
!test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state)) {
phylink_mac_config(pl, &pl->link_config);
phylink_mac_an_restart(pl);
@@ -1345,7 +1348,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
pause->tx_pause);
} else if (!test_bit(PHYLINK_DISABLE_STOPPED,
&pl->phylink_disable_state)) {
- switch (pl->link_an_mode) {
+ switch (pl->cur_link_an_mode) {
case MLO_AN_FIXED:
/* Should we allow fixed links to change against the config? */
phylink_resolve_flow(pl, config);
@@ -1552,7 +1555,7 @@ static int phylink_mii_read(struct phylink *pl, unsigned int phy_id,
struct phylink_link_state state;
int val = 0xffff;
- switch (pl->link_an_mode) {
+ switch (pl->cur_link_an_mode) {
case MLO_AN_FIXED:
if (phy_id == 0) {
phylink_get_fixed_state(pl, &state);
@@ -1580,7 +1583,7 @@ static int phylink_mii_read(struct phylink *pl, unsigned int phy_id,
static int phylink_mii_write(struct phylink *pl, unsigned int phy_id,
unsigned int reg, unsigned int val)
{
- switch (pl->link_an_mode) {
+ switch (pl->cur_link_an_mode) {
case MLO_AN_FIXED:
break;
@@ -1753,10 +1756,10 @@ static int phylink_sfp_module_insert(void *upstream,
linkmode_copy(pl->link_config.advertising, config.advertising);
}
- if (pl->link_an_mode != MLO_AN_INBAND ||
+ if (pl->cur_link_an_mode != MLO_AN_INBAND ||
pl->link_config.interface != config.interface) {
pl->link_config.interface = config.interface;
- pl->link_an_mode = MLO_AN_INBAND;
+ pl->cur_link_an_mode = MLO_AN_INBAND;
changed = true;
--
2.20.1
next prev parent reply other threads:[~2019-12-09 14:07 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-09 14:02 [PATCH net-next 00/14] Add support for SFP+ copper modules Russell King - ARM Linux admin
2019-12-09 14:06 ` [PATCH net-next 01/14] net: sfp: remove incomplete 100BASE-FX and 100BASE-LX support Russell King
2019-12-09 14:06 ` [PATCH net-next 02/14] net: sfp: derive interface mode from ethtool link modes Russell King
2019-12-09 14:06 ` [PATCH net-next 03/14] net: sfp: add more extended compliance codes Russell King
2019-12-09 14:07 ` [PATCH net-next 04/14] net: sfp: add module start/stop upstream notifications Russell King
2019-12-09 14:07 ` [PATCH net-next 05/14] net: sfp: move phy_start()/phy_stop() to phylink Russell King
2019-12-09 14:07 ` [PATCH net-next 06/14] net: mdio-i2c: add support for Clause 45 accesses Russell King
2019-12-09 14:07 ` [PATCH net-next 07/14] net: phylink: re-split __phylink_connect_phy() Russell King
2019-12-09 14:07 ` [PATCH net-next 08/14] net: phylink: support Clause 45 PHYs on SFP+ modules Russell King
2019-12-09 14:07 ` Russell King [this message]
2019-12-09 14:07 ` [PATCH net-next 10/14] net: phylink: split phylink_sfp_module_insert() Russell King
2019-12-09 14:07 ` [PATCH net-next 11/14] net: phylink: delay MAC configuration for copper SFP modules Russell King
2019-12-09 14:49 ` Russell King - ARM Linux admin
2019-12-09 14:07 ` [PATCH net-next 12/14] net: phylink: make Broadcom BCM84881 based SFPs work Russell King
2019-12-09 14:07 ` [PATCH net-next 13/14] net: phy: add Broadcom BCM84881 PHY driver Russell King
2019-12-09 14:07 ` [PATCH net-next 14/14] net: sfp: add support for Clause 45 PHYs Russell King
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1ieJh9-0004P8-St@rmk-PC.armlinux.org.uk \
--to=rmk+kernel@armlinux.org.uk \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).