[PATCH net-next 8/8] net: mvpp2: use resolved link config in mac_link_up()

[Russell King <rmk+kernel@armlinux.org.uk>]

Convert the Marvell mvpp2 ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/marvell/mvpp2/mvpp2_main.c   | 83 +++++++++++--------
 1 file changed, 47 insertions(+), 36 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index ed8042d97e29..6b9c7ed2547e 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4976,15 +4976,13 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl2 = ctrl2 = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
-	an &= ~(MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_CONFIG_GMII_SPEED |
-		MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
+	an &= ~(MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
 		MVPP2_GMAC_FC_ADV_ASM_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG |
-		MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_AN_DUPLEX_EN |
-		MVPP2_GMAC_IN_BAND_AUTONEG | MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
+		MVPP2_GMAC_AN_DUPLEX_EN | MVPP2_GMAC_IN_BAND_AUTONEG |
+		MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
 	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PORT_RESET_MASK |
 		   MVPP2_GMAC_PCS_ENABLE_MASK);
-	ctrl4 &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {
@@ -5014,31 +5012,20 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 
 	/* Configure negotiation style */
 	if (!phylink_autoneg_inband(mode)) {
-		/* Phy or fixed speed - no in-band AN */
-		if (state->duplex)
-			an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
-		if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
-			an |= MVPP2_GMAC_CONFIG_GMII_SPEED;
-		else if (state->speed == SPEED_100)
-			an |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
-		if (state->pause & MLO_PAUSE_TX)
-			ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-		if (state->pause & MLO_PAUSE_RX)
-			ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
+		/* Phy or fixed speed - no in-band AN, nothing to do, leave the
+		 * configured speed, duplex and flow control as-is.
+		 */
 	} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
 		/* SGMII in-band mode receives the speed and duplex from
 		 * the PHY. Flow control information is not received. */
-		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+			MVPP2_GMAC_FORCE_LINK_PASS |
+			MVPP2_GMAC_CONFIG_MII_SPEED |
+			MVPP2_GMAC_CONFIG_GMII_SPEED |
+			MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 		an |= MVPP2_GMAC_IN_BAND_AUTONEG |
 		      MVPP2_GMAC_AN_SPEED_EN |
 		      MVPP2_GMAC_AN_DUPLEX_EN;
-
-		if (state->pause & MLO_PAUSE_TX)
-			ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-		if (state->pause & MLO_PAUSE_RX)
-			ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
 	} else if (phy_interface_mode_is_8023z(state->interface)) {
 		/* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
 		 * they negotiate duplex: they are always operating with a fixed
@@ -5046,19 +5033,17 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 		 * speed and full duplex here.
 		 */
 		ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
-		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+			MVPP2_GMAC_FORCE_LINK_PASS |
+			MVPP2_GMAC_CONFIG_MII_SPEED |
+			MVPP2_GMAC_CONFIG_GMII_SPEED |
+			MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 		an |= MVPP2_GMAC_IN_BAND_AUTONEG |
 		      MVPP2_GMAC_CONFIG_GMII_SPEED |
 		      MVPP2_GMAC_CONFIG_FULL_DUPLEX;
 
-		if (state->pause & MLO_PAUSE_AN && state->an_enabled) {
+		if (state->pause & MLO_PAUSE_AN && state->an_enabled)
 			an |= MVPP2_GMAC_FLOW_CTRL_AUTONEG;
-		} else {
-			if (state->pause & MLO_PAUSE_TX)
-				ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-			if (state->pause & MLO_PAUSE_RX)
-				ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
-		}
 	}
 
 /* Some fields of the auto-negotiation register require the port to be down when
@@ -5155,18 +5140,44 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 	struct mvpp2_port *port = netdev_priv(dev);
 	u32 val;
 
-	if (!phylink_autoneg_inband(mode)) {
-		if (mvpp2_is_xlg(interface)) {
+	if (mvpp2_is_xlg(interface)) {
+		if (!phylink_autoneg_inband(mode)) {
 			val = readl(port->base + MVPP22_XLG_CTRL0_REG);
 			val &= ~MVPP22_XLG_CTRL0_FORCE_LINK_DOWN;
 			val |= MVPP22_XLG_CTRL0_FORCE_LINK_PASS;
 			writel(val, port->base + MVPP22_XLG_CTRL0_REG);
-		} else {
+		}
+	} else {
+		if (!phylink_autoneg_inband(mode)) {
 			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
+			val &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+				 MVPP2_GMAC_CONFIG_MII_SPEED |
+				 MVPP2_GMAC_CONFIG_GMII_SPEED |
+				 MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 			val |= MVPP2_GMAC_FORCE_LINK_PASS;
+
+			if (speed == SPEED_1000 || speed == SPEED_2500)
+				val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+			else if (speed == SPEED_100)
+				val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+			if (duplex == DUPLEX_FULL)
+				val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
 			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
 		}
+
+		/* We can always update the flow control enable bits;
+		 * these will only be effective if flow control AN
+		 * (MVPP2_GMAC_FLOW_CTRL_AUTONEG) is disabled.
+		 */
+		val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+		val &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
+		if (tx_pause)
+			val |= MVPP22_CTRL4_TX_FC_EN;
+		if (rx_pause)
+			val |= MVPP22_CTRL4_RX_FC_EN;
+		writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
 	}
 
 	mvpp2_port_enable(port);
-- 
2.20.1