From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
To: Andrew Lunn <andrew@lunn.ch>, Heiner Kallweit <hkallweit1@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
netdev@vger.kernel.org,
Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>,
Paolo Abeni <pabeni@redhat.com>
Subject: [PATCH net-next] net: stmmac: visconti: convert to set_clk_tx_rate() method
Date: Tue, 15 Apr 2025 17:52:48 +0100 [thread overview]
Message-ID: <E1u4jWi-000rJi-Rg@rmk-PC.armlinux.org.uk> (raw)
Convert visconti to use the set_clk_tx_rate() method. By doing so,
the GMAC control register will already have been updated (unlike with
the fix_mac_speed() method) so this code can be removed while porting
to the set_clk_tx_rate() method.
There is also no need for the spinlock, and has never been - neither
fix_mac_speed() nor set_clk_tx_rate() can be called by more than one
thread at a time, so the lock does nothing useful.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
.../ethernet/stmicro/stmmac/dwmac-visconti.c | 18 ++++--------------
1 file changed, 4 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
index e1de471b215c..2215aef3ef42 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
@@ -51,22 +51,16 @@ struct visconti_eth {
u32 phy_intf_sel;
struct clk *phy_ref_clk;
struct device *dev;
- spinlock_t lock; /* lock to protect register update */
};
-static void visconti_eth_fix_mac_speed(void *priv, int speed, unsigned int mode)
+static int visconti_eth_set_clk_tx_rate(void *bsp_priv, struct clk *clk_tx_i,
+ phy_interface_t interface, int speed)
{
struct visconti_eth *dwmac = priv;
struct net_device *netdev = dev_get_drvdata(dwmac->dev);
unsigned int val, clk_sel_val = 0;
unsigned long flags;
- spin_lock_irqsave(&dwmac->lock, flags);
-
- /* adjust link */
- val = readl(dwmac->reg + MAC_CTRL_REG);
- val &= ~(GMAC_CONFIG_PS | GMAC_CONFIG_FES);
-
switch (speed) {
case SPEED_1000:
if (dwmac->phy_intf_sel == ETHER_CONFIG_INTF_RGMII)
@@ -89,12 +83,9 @@ static void visconti_eth_fix_mac_speed(void *priv, int speed, unsigned int mode)
default:
/* No bit control */
netdev_err(netdev, "Unsupported speed request (%d)", speed);
- spin_unlock_irqrestore(&dwmac->lock, flags);
return;
}
- writel(val, dwmac->reg + MAC_CTRL_REG);
-
/* Stop internal clock */
val = readl(dwmac->reg + REG_ETHER_CLOCK_SEL);
val &= ~(ETHER_CLK_SEL_RMII_CLK_EN | ETHER_CLK_SEL_RX_TX_CLK_EN);
@@ -136,7 +127,7 @@ static void visconti_eth_fix_mac_speed(void *priv, int speed, unsigned int mode)
break;
}
- spin_unlock_irqrestore(&dwmac->lock, flags);
+ return 0;
}
static int visconti_eth_init_hw(struct platform_device *pdev, struct plat_stmmacenet_data *plat_dat)
@@ -228,7 +219,6 @@ static int visconti_eth_dwmac_probe(struct platform_device *pdev)
if (!dwmac)
return -ENOMEM;
- spin_lock_init(&dwmac->lock);
dwmac->reg = stmmac_res.addr;
dwmac->dev = &pdev->dev;
@@ -237,7 +227,7 @@ static int visconti_eth_dwmac_probe(struct platform_device *pdev)
__set_bit(PHY_INTERFACE_MODE_RMII, plat_dat->supported_interfaces);
plat_dat->bsp_priv = dwmac;
- plat_dat->fix_mac_speed = visconti_eth_fix_mac_speed;
+ plat_dat->set_clk_tx_rate = visconti_eth_set_clk_tx_rate;
ret = visconti_eth_clock_probe(pdev, plat_dat);
if (ret)
--
2.30.2
next reply other threads:[~2025-04-15 16:53 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-04-15 16:52 Russell King (Oracle) [this message]
2025-04-15 16:58 ` [PATCH net-next] net: stmmac: visconti: convert to set_clk_tx_rate() method Andrew Lunn
2025-04-16 4:56 ` nobuhiro1.iwamatsu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1u4jWi-000rJi-Rg@rmk-PC.armlinux.org.uk \
--to=rmk+kernel@armlinux.org.uk \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=nobuhiro1.iwamatsu@toshiba.co.jp \
--cc=pabeni@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).