From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
To: Andrew Lunn <andrew@lunn.ch>, Heiner Kallweit <hkallweit1@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>,
linux-arm-kernel@lists.infradead.org,
linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>,
Neil Armstrong <neil.armstrong@linaro.org>,
netdev@vger.kernel.org, Paolo Abeni <pabeni@redhat.com>,
Vinod Koul <vkoul@kernel.org>
Subject: [PATCH net-next 04/14] net: stmmac: wrap phylink's rx_clk_stop functions
Date: Wed, 14 Jan 2026 17:45:29 +0000 [thread overview]
Message-ID: <E1vg4vx-00000003SFz-1ldy@rmk-PC.armlinux.org.uk> (raw)
In-Reply-To: <aWfWDsCoBc3YRKKo@shell.armlinux.org.uk>
With generic SerDes support, stmmac will need to do more work to ensure
that clk_rx_i is running in all configurations. Rather than turn each
site that calls phylink_rx_clk_stop_xxx() into a list of functions,
move these to their own pair of functions so that they can be
augmented at a single location.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 32 ++++++++++++-------
1 file changed, 21 insertions(+), 11 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index c2589f02ff7e..24a2555ca329 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3547,6 +3547,16 @@ static void stmmac_safety_feat_configuration(struct stmmac_priv *priv)
}
}
+static void stmmac_clk_rx_i_require(struct stmmac_priv *priv)
+{
+ phylink_rx_clk_stop_block(priv->phylink);
+}
+
+static void stmmac_clk_rx_i_release(struct stmmac_priv *priv)
+{
+ phylink_rx_clk_stop_unblock(priv->phylink);
+}
+
/**
* stmmac_hw_setup - setup mac in a usable state.
* @dev : pointer to the device structure.
@@ -3578,12 +3588,12 @@ static int stmmac_hw_setup(struct net_device *dev)
* Block the receive clock stop for LPI mode at the PHY in case
* the link is established with EEE mode active.
*/
- phylink_rx_clk_stop_block(priv->phylink);
+ stmmac_clk_rx_i_require(priv);
/* DMA initialization and SW reset */
ret = stmmac_init_dma_engine(priv);
if (ret < 0) {
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
netdev_err(priv->dev, "%s: DMA engine initialization failed\n",
__func__);
return ret;
@@ -3591,7 +3601,7 @@ static int stmmac_hw_setup(struct net_device *dev)
/* Copy the MAC addr into the HW */
stmmac_set_umac_addr(priv, priv->hw, dev->dev_addr, 0);
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
/* Initialize the MAC Core */
stmmac_core_init(priv, priv->hw, dev);
@@ -3670,9 +3680,9 @@ static int stmmac_hw_setup(struct net_device *dev)
/* Start the ball rolling... */
stmmac_start_all_dma(priv);
- phylink_rx_clk_stop_block(priv->phylink);
+ stmmac_clk_rx_i_require(priv);
stmmac_set_hw_vlan_mode(priv, priv->hw);
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
return 0;
}
@@ -6107,9 +6117,9 @@ static int stmmac_set_features(struct net_device *netdev,
else
priv->hw->hw_vlan_en = false;
- phylink_rx_clk_stop_block(priv->phylink);
+ stmmac_clk_rx_i_require(priv);
stmmac_set_hw_vlan_mode(priv, priv->hw);
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
return 0;
}
@@ -6378,9 +6388,9 @@ static int stmmac_set_mac_address(struct net_device *ndev, void *addr)
if (ret)
goto set_mac_error;
- phylink_rx_clk_stop_block(priv->phylink);
+ stmmac_clk_rx_i_require(priv);
stmmac_set_umac_addr(priv, priv->hw, ndev->dev_addr, 0);
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
set_mac_error:
pm_runtime_put(priv->device);
@@ -8192,11 +8202,11 @@ int stmmac_resume(struct device *dev)
stmmac_init_timestamping(priv);
stmmac_init_coalesce(priv);
- phylink_rx_clk_stop_block(priv->phylink);
+ stmmac_clk_rx_i_require(priv);
stmmac_set_rx_mode(ndev);
stmmac_restore_hw_vlan_rx_fltr(priv, ndev, priv->hw);
- phylink_rx_clk_stop_unblock(priv->phylink);
+ stmmac_clk_rx_i_release(priv);
stmmac_enable_all_queues(priv);
stmmac_enable_all_dma_irq(priv);
--
2.47.3
next prev parent reply other threads:[~2026-01-14 17:45 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-14 17:44 [PATCH RFC net-next 00/14] net: stmmac: SerDes, PCS, BASE-X, and inband goodies Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 01/14] net: stmmac: qcom-ethqos: remove mac_base Russell King (Oracle)
2026-01-14 20:48 ` Vladimir Oltean
2026-01-14 17:45 ` [PATCH net-next 02/14] net: stmmac: qcom-ethqos: convert to set_clk_tx_rate() method Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 03/14] phy: qcom-sgmii-eth: add .set_mode() and .validate() methods Russell King (Oracle)
2026-01-14 18:47 ` Vladimir Oltean
2026-01-14 18:55 ` Russell King (Oracle)
2026-01-14 19:02 ` Vladimir Oltean
2026-01-15 10:11 ` kernel test robot
2026-01-15 10:23 ` kernel test robot
2026-01-14 17:45 ` Russell King (Oracle) [this message]
2026-01-15 14:47 ` [PATCH net-next 04/14] net: stmmac: wrap phylink's rx_clk_stop functions Maxime Chevallier
2026-01-14 17:45 ` [PATCH net-next 05/14] net: stmmac: add stmmac core serdes support Russell King (Oracle)
2026-01-15 14:48 ` Maxime Chevallier
2026-01-15 15:15 ` Russell King (Oracle)
2026-01-16 2:57 ` [net-next,05/14] " Jakub Kicinski
2026-01-14 17:45 ` [PATCH net-next 06/14] net: stmmac: qcom-ethqos: convert to dwmac generic SerDes support Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 07/14] net: stmmac: move most PCS register definitions to stmmac_pcs.c Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 08/14] net: stmmac: handle integrated PCS phy_intf_sel separately Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 09/14] net: stmmac: add BASE-X support to integrated PCS Russell King (Oracle)
2026-01-14 17:46 ` [PATCH net-next 10/14] net: stmmac: use integrated PCS for BASE-X modes Russell King (Oracle)
2026-01-14 17:46 ` [PATCH net-next 11/14] net: stmmac: add struct stmmac_pcs_info Russell King (Oracle)
2026-01-14 17:46 ` [PATCH net-next 12/14] net: stmmac: add support for reading inband SGMII status Russell King (Oracle)
2026-01-16 2:58 ` [net-next,12/14] " Jakub Kicinski
2026-01-14 17:46 ` [PATCH net-next 13/14] net: stmmac: configure SGMII AN control according to phylink Russell King (Oracle)
2026-01-14 17:46 ` [PATCH net-next 14/14] net: stmmac: report PCS configuration changes Russell King (Oracle)
-- strict thread matches above, loose matches on Subject: below --
2026-01-19 12:32 [PATCH net-next 00/14] net: stmmac: SerDes, PCS, BASE-X, and inband goodies Russell King (Oracle)
2026-01-19 12:33 ` [PATCH net-next 04/14] net: stmmac: wrap phylink's rx_clk_stop functions Russell King (Oracle)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1vg4vx-00000003SFz-1ldy@rmk-PC.armlinux.org.uk \
--to=rmk+kernel@armlinux.org.uk \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=hkallweit1@gmail.com \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=mohd.anwar@oss.qualcomm.com \
--cc=neil.armstrong@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox