From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
To: Andrew Lunn <andrew@lunn.ch>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>,
netdev@vger.kernel.org, Paolo Abeni <pabeni@redhat.com>
Subject: [PATCH net-next 4/4] net: stmmac: move serdes power methods to stmmac_[open|release]()
Date: Tue, 03 Feb 2026 10:01:29 +0000 [thread overview]
Message-ID: <E1vnDDt-00000007XxF-3uUK@rmk-PC.armlinux.org.uk> (raw)
In-Reply-To: <aYHHWm5UkD1JVa7D@shell.armlinux.org.uk>
Move the SerDes power up and down calls for the non-"after linkup"
case out of __stmmac_open() and __stmmac_release() into the
stmmac_open() and stmmac_release() methods, which means the SerDes
will only change power state on administrative changes or suspend/
resume, not while changing the interface MTU.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 21 +++++++++----------
1 file changed, 10 insertions(+), 11 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 05b0b080bade..d561b0a0f5ac 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -4134,12 +4134,6 @@ static int __stmmac_open(struct net_device *dev,
stmmac_reset_queues_param(priv);
- if (!(priv->plat->flags & STMMAC_FLAG_SERDES_UP_AFTER_PHY_LINKUP)) {
- ret = stmmac_legacy_serdes_power_up(priv);
- if (ret < 0)
- return ret;
- }
-
ret = stmmac_hw_setup(dev);
if (ret < 0) {
netdev_err(priv->dev, "%s: Hw setup failed\n", __func__);
@@ -4170,7 +4164,6 @@ static int __stmmac_open(struct net_device *dev,
stmmac_release_ptp(priv);
init_error:
- stmmac_legacy_serdes_power_down(priv);
return ret;
}
@@ -4196,9 +4189,15 @@ static int stmmac_open(struct net_device *dev)
if (ret)
goto err_runtime_pm;
+ if (!(priv->plat->flags & STMMAC_FLAG_SERDES_UP_AFTER_PHY_LINKUP)) {
+ ret = stmmac_legacy_serdes_power_up(priv);
+ if (ret < 0)
+ goto err_disconnect_phy;
+ }
+
ret = __stmmac_open(dev, dma_conf);
if (ret)
- goto err_disconnect_phy;
+ goto err_serdes;
kfree(dma_conf);
@@ -4207,6 +4206,8 @@ static int stmmac_open(struct net_device *dev)
return ret;
+err_serdes:
+ stmmac_legacy_serdes_power_down(priv);
err_disconnect_phy:
phylink_disconnect_phy(priv->phylink);
err_runtime_pm:
@@ -4241,9 +4242,6 @@ static void __stmmac_release(struct net_device *dev)
/* Release and free the Rx/Tx resources */
free_dma_desc_resources(priv, &priv->dma_conf);
- /* Powerdown Serdes if there is */
- stmmac_legacy_serdes_power_down(priv);
-
stmmac_release_ptp(priv);
if (stmmac_fpe_supported(priv))
@@ -4269,6 +4267,7 @@ static int stmmac_release(struct net_device *dev)
__stmmac_release(dev);
+ stmmac_legacy_serdes_power_down(priv);
phylink_disconnect_phy(priv->phylink);
pm_runtime_put(priv->device);
--
2.47.3
next prev parent reply other threads:[~2026-02-03 10:01 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-03 10:00 [PATCH net-next 0/4] net: stmmac: fix serdes power methods Russell King (Oracle)
2026-02-03 10:01 ` [PATCH net-next 1/4] net: stmmac: add wrappers for serdes_power[up|down]() methods Russell King (Oracle)
2026-02-03 10:01 ` [PATCH net-next 2/4] net: stmmac: add state tracking for legacy serdes power state Russell King (Oracle)
2026-02-03 10:01 ` [PATCH net-next 3/4] net: stmmac: add missing serdes power down in error paths Russell King (Oracle)
2026-02-03 10:01 ` Russell King (Oracle) [this message]
2026-02-05 5:00 ` [PATCH net-next 0/4] net: stmmac: fix serdes power methods patchwork-bot+netdevbpf
2026-02-05 10:28 ` Mohd Ayaan Anwar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1vnDDt-00000007XxF-3uUK@rmk-PC.armlinux.org.uk \
--to=rmk+kernel@armlinux.org.uk \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mohd.anwar@oss.qualcomm.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox