From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
To: Andrew Lunn <andrew@lunn.ch>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>,
Neil Armstrong <neil.armstrong@linaro.org>,
netdev@vger.kernel.org, Paolo Abeni <pabeni@redhat.com>,
Vinod Koul <vkoul@kernel.org>
Subject: [PATCH RESEND2 net-next 8/8] net: stmmac: qcom-ethqos: remove phy_set_mode_ext() after phy_power_on()
Date: Thu, 26 Feb 2026 23:09:57 +0000 [thread overview]
Message-ID: <E1vvkUX-0000000AuPo-3mEw@rmk-PC.armlinux.org.uk> (raw)
In-Reply-To: <aaDSJAc-x2-klvHJ@shell.armlinux.org.uk>
The call to phy_set_mode_ext() after phy_power_on() was a work-around
for the qcom-sgmii-eth SerDes driver that only re-enabled its clocks on
phy_power_on() but did not configure the PHY. Now that the SerDes driver
fully configures the SerDes at phy_power_on(), there is no need to call
phy_set_mode_ext() immediately afterwards.
This also means we no longer need to record the previous operating mode
of the driver - this is up to the SerDes driver. In any case, the only
thing that we care about is the SerDes provides the necessary clocks to
the stmmac core to allow it to reset at this point. The actual mode is
irrelevant at this point as the correct mode will be configured in
ethqos_mac_finish_serdes() just before the network device is brought
online.
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
.../stmicro/stmmac/dwmac-qcom-ethqos.c | 18 ++----------------
1 file changed, 2 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
index 8913f6f02b9e..cb1c074c2053 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
@@ -105,7 +105,6 @@ struct qcom_ethqos {
struct clk *link_clk;
struct phy *serdes_phy;
- phy_interface_t serdes_mode;
phy_interface_t phy_mode;
const struct ethqos_emac_por *rgmii_por;
@@ -648,17 +647,8 @@ static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
return ret;
ret = phy_power_on(ethqos->serdes_phy);
- if (ret) {
- phy_exit(ethqos->serdes_phy);
- return ret;
- }
-
- ret = phy_set_mode_ext(ethqos->serdes_phy, PHY_MODE_ETHERNET,
- ethqos->serdes_mode);
- if (ret) {
- phy_power_off(ethqos->serdes_phy);
+ if (ret)
phy_exit(ethqos->serdes_phy);
- }
return ret;
}
@@ -681,12 +671,9 @@ static int ethqos_mac_finish_serdes(struct net_device *ndev, void *priv,
qcom_ethqos_set_sgmii_loopback(ethqos, false);
if (interface == PHY_INTERFACE_MODE_SGMII ||
- interface == PHY_INTERFACE_MODE_2500BASEX) {
+ interface == PHY_INTERFACE_MODE_2500BASEX)
ret = phy_set_mode_ext(ethqos->serdes_phy, PHY_MODE_ETHERNET,
interface);
- if (ret == 0)
- ethqos->serdes_mode = interface;
- }
return ret;
}
@@ -839,7 +826,6 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
plat_dat->host_dma_width = data->dma_addr_width;
if (ethqos->serdes_phy) {
- ethqos->serdes_mode = PHY_INTERFACE_MODE_SGMII;
plat_dat->serdes_powerup = qcom_ethqos_serdes_powerup;
plat_dat->serdes_powerdown = qcom_ethqos_serdes_powerdown;
}
--
2.47.3
next prev parent reply other threads:[~2026-02-26 23:10 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-26 23:07 [PATCH RESEND2 net-next 0/8] net: stmmac: qcom-ethqos: further serdes reorganisation Russell King (Oracle)
2026-02-26 23:09 ` [PATCH RESEND2 net-next 1/8] net: stmmac: qcom-ethqos: move ethqos_set_serdes_speed() Russell King (Oracle)
2026-02-26 23:09 ` [PATCH RESEND2 net-next 2/8] phy: qcom-sgmii-eth: add .set_mode() and .validate() methods Russell King (Oracle)
2026-02-26 23:09 ` [PATCH RESEND2 net-next 3/8] net: stmmac: qcom-ethqos: convert to use phy_set_mode_ext() Russell King (Oracle)
2026-02-26 23:09 ` [PATCH RESEND2 net-next 4/8] phy: qcom-sgmii-eth: remove .set_speed() implementation Russell King (Oracle)
2026-02-27 15:39 ` Vladimir Oltean
2026-02-26 23:09 ` [PATCH RESEND2 net-next 5/8] phy: qcom-sgmii-eth: use PHY interface mode for SerDes settings Russell King (Oracle)
2026-02-27 15:40 ` Vladimir Oltean
2026-02-26 23:09 ` [PATCH RESEND2 net-next 6/8] phy: qcom-sgmii-eth: remove qcom_dwmac_sgmii_phy_interface() Russell King (Oracle)
2026-02-27 15:42 ` Vladimir Oltean
2026-02-26 23:09 ` [PATCH RESEND2 net-next 7/8] phy: qcom-sgmii-eth: relax order of .power_on() vs .set_mode*() Russell King (Oracle)
2026-02-27 15:37 ` Vladimir Oltean
2026-02-26 23:09 ` Russell King (Oracle) [this message]
2026-02-27 15:31 ` [PATCH RESEND2 net-next 8/8] net: stmmac: qcom-ethqos: remove phy_set_mode_ext() after phy_power_on() Vladimir Oltean
2026-02-27 1:26 ` [PATCH RESEND2 net-next 0/8] net: stmmac: qcom-ethqos: further serdes reorganisation Jakub Kicinski
2026-02-27 15:48 ` Vladimir Oltean
2026-02-28 0:11 ` Russell King (Oracle)
2026-02-28 0:55 ` Jakub Kicinski
2026-02-28 16:31 ` Jakub Kicinski
2026-03-01 0:14 ` Vladimir Oltean
2026-03-01 0:32 ` Jakub Kicinski
2026-03-01 12:08 ` Vladimir Oltean
2026-03-02 23:29 ` Jakub Kicinski
2026-03-01 13:42 ` Russell King (Oracle)
2026-03-01 14:10 ` Vladimir Oltean
2026-03-01 13:39 ` Russell King (Oracle)
2026-03-02 23:57 ` Jakub Kicinski
2026-03-09 15:44 ` Vladimir Oltean
2026-03-09 23:51 ` Jakub Kicinski
2026-03-03 0:00 ` patchwork-bot+netdevbpf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1vvkUX-0000000AuPo-3mEw@rmk-PC.armlinux.org.uk \
--to=rmk+kernel@armlinux.org.uk \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mohd.anwar@oss.qualcomm.com \
--cc=neil.armstrong@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox