* [PATCH bpf-next] selftests: xsk: changes for setting up NICs to run xsk self-tests
@ 2022-11-30 9:41 Tirthendu Sarkar
2022-11-30 11:57 ` Maciej Fijalkowski
0 siblings, 1 reply; 3+ messages in thread
From: Tirthendu Sarkar @ 2022-11-30 9:41 UTC (permalink / raw)
To: bjorn, magnus.karlsson, maciej.fijalkowski, jonathan.lemon, ast,
daniel
Cc: netdev, bpf
ETH devies need to be set up for running xsk self-tests, like enable
loopback, set promiscuous mode, MTU etc. This patch adds those settings
before running xsk self-tests and reverts them back once done.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
---
tools/testing/selftests/bpf/test_xsk.sh | 27 ++++++++++++++++++++++++-
1 file changed, 26 insertions(+), 1 deletion(-)
diff --git a/tools/testing/selftests/bpf/test_xsk.sh b/tools/testing/selftests/bpf/test_xsk.sh
index d821fd098504..e7a5c5fc4f71 100755
--- a/tools/testing/selftests/bpf/test_xsk.sh
+++ b/tools/testing/selftests/bpf/test_xsk.sh
@@ -106,7 +106,11 @@ MTU=1500
trap ctrl_c INT
function ctrl_c() {
- cleanup_exit ${VETH0} ${VETH1} ${NS1}
+ if [ ! -z $ETH ]; then
+ cleanup_exit ${VETH0} ${VETH1} ${NS1}
+ else
+ cleanup_eth
+ fi
exit 1
}
@@ -138,9 +142,28 @@ setup_vethPairs() {
ip link set ${VETH0} up
}
+setup_eth() {
+ sudo ethtool -L ${ETH} combined 1
+ sudo ethtool -K ${ETH} loopback on
+ sudo ip link set ${ETH} promisc on
+ sudo ip link set ${ETH} mtu ${MTU}
+ sudo ip link set ${ETH} up
+ IPV6_DISABLE_CMD="sudo sysctl -n net.ipv6.conf.${ETH}.disable_ipv6"
+ IPV6_DISABLE=`$IPV6_DISABLE_CMD 2> /dev/null`
+ [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=1
+ sleep 1
+}
+
+cleanup_eth() {
+ [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=0
+ sudo ethtool -K ${ETH} loopback off
+ sudo ip link set ${ETH} promisc off
+}
+
if [ ! -z $ETH ]; then
VETH0=${ETH}
VETH1=${ETH}
+ setup_eth
NS1=""
else
validate_root_exec
@@ -191,6 +214,8 @@ exec_xskxceiver
if [ -z $ETH ]; then
cleanup_exit ${VETH0} ${VETH1} ${NS1}
+else
+ cleanup_eth
fi
failures=0
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH bpf-next] selftests: xsk: changes for setting up NICs to run xsk self-tests
2022-11-30 9:41 [PATCH bpf-next] selftests: xsk: changes for setting up NICs to run xsk self-tests Tirthendu Sarkar
@ 2022-11-30 11:57 ` Maciej Fijalkowski
2022-11-30 12:13 ` Magnus Karlsson
0 siblings, 1 reply; 3+ messages in thread
From: Maciej Fijalkowski @ 2022-11-30 11:57 UTC (permalink / raw)
To: Tirthendu Sarkar
Cc: bjorn, magnus.karlsson, jonathan.lemon, ast, daniel, netdev, bpf
On Wed, Nov 30, 2022 at 03:11:42PM +0530, Tirthendu Sarkar wrote:
> ETH devies need to be set up for running xsk self-tests, like enable
> loopback, set promiscuous mode, MTU etc. This patch adds those settings
> before running xsk self-tests and reverts them back once done.
>
> Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
> ---
> tools/testing/selftests/bpf/test_xsk.sh | 27 ++++++++++++++++++++++++-
> 1 file changed, 26 insertions(+), 1 deletion(-)
>
> diff --git a/tools/testing/selftests/bpf/test_xsk.sh b/tools/testing/selftests/bpf/test_xsk.sh
> index d821fd098504..e7a5c5fc4f71 100755
> --- a/tools/testing/selftests/bpf/test_xsk.sh
> +++ b/tools/testing/selftests/bpf/test_xsk.sh
> @@ -106,7 +106,11 @@ MTU=1500
> trap ctrl_c INT
>
> function ctrl_c() {
> - cleanup_exit ${VETH0} ${VETH1} ${NS1}
> + if [ ! -z $ETH ]; then
> + cleanup_exit ${VETH0} ${VETH1} ${NS1}
> + else
> + cleanup_eth
> + fi
> exit 1
> }
>
> @@ -138,9 +142,28 @@ setup_vethPairs() {
> ip link set ${VETH0} up
> }
>
> +setup_eth() {
> + sudo ethtool -L ${ETH} combined 1
what if particular device has a different way of configuring single
channel? like
$ sudo ethtool -L ${ETH} tx 1 rx 1
I am not sure if we want to proceed with settings that are specific to
Intel devices. What if mlx5 will this in a much different way?
> + sudo ethtool -K ${ETH} loopback on
> + sudo ip link set ${ETH} promisc on
> + sudo ip link set ${ETH} mtu ${MTU}
> + sudo ip link set ${ETH} up
> + IPV6_DISABLE_CMD="sudo sysctl -n net.ipv6.conf.${ETH}.disable_ipv6"
> + IPV6_DISABLE=`$IPV6_DISABLE_CMD 2> /dev/null`
> + [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=1
> + sleep 1
> +}
> +
> +cleanup_eth() {
> + [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=0
> + sudo ethtool -K ${ETH} loopback off
> + sudo ip link set ${ETH} promisc off
> +}
> +
> if [ ! -z $ETH ]; then
> VETH0=${ETH}
> VETH1=${ETH}
> + setup_eth
> NS1=""
> else
> validate_root_exec
> @@ -191,6 +214,8 @@ exec_xskxceiver
>
> if [ -z $ETH ]; then
> cleanup_exit ${VETH0} ${VETH1} ${NS1}
> +else
> + cleanup_eth
> fi
>
> failures=0
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH bpf-next] selftests: xsk: changes for setting up NICs to run xsk self-tests
2022-11-30 11:57 ` Maciej Fijalkowski
@ 2022-11-30 12:13 ` Magnus Karlsson
0 siblings, 0 replies; 3+ messages in thread
From: Magnus Karlsson @ 2022-11-30 12:13 UTC (permalink / raw)
To: Maciej Fijalkowski, Saeed Mahameed
Cc: Tirthendu Sarkar, bjorn, magnus.karlsson, jonathan.lemon, ast,
daniel, netdev, bpf
On Wed, Nov 30, 2022 at 1:09 PM Maciej Fijalkowski
<maciej.fijalkowski@intel.com> wrote:
>
> On Wed, Nov 30, 2022 at 03:11:42PM +0530, Tirthendu Sarkar wrote:
> > ETH devies need to be set up for running xsk self-tests, like enable
> > loopback, set promiscuous mode, MTU etc. This patch adds those settings
> > before running xsk self-tests and reverts them back once done.
> >
> > Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
> > ---
> > tools/testing/selftests/bpf/test_xsk.sh | 27 ++++++++++++++++++++++++-
> > 1 file changed, 26 insertions(+), 1 deletion(-)
> >
> > diff --git a/tools/testing/selftests/bpf/test_xsk.sh b/tools/testing/selftests/bpf/test_xsk.sh
> > index d821fd098504..e7a5c5fc4f71 100755
> > --- a/tools/testing/selftests/bpf/test_xsk.sh
> > +++ b/tools/testing/selftests/bpf/test_xsk.sh
> > @@ -106,7 +106,11 @@ MTU=1500
> > trap ctrl_c INT
> >
> > function ctrl_c() {
> > - cleanup_exit ${VETH0} ${VETH1} ${NS1}
> > + if [ ! -z $ETH ]; then
> > + cleanup_exit ${VETH0} ${VETH1} ${NS1}
> > + else
> > + cleanup_eth
> > + fi
> > exit 1
> > }
> >
> > @@ -138,9 +142,28 @@ setup_vethPairs() {
> > ip link set ${VETH0} up
> > }
> >
> > +setup_eth() {
> > + sudo ethtool -L ${ETH} combined 1
>
> what if particular device has a different way of configuring single
> channel? like
>
> $ sudo ethtool -L ${ETH} tx 1 rx 1
>
> I am not sure if we want to proceed with settings that are specific to
> Intel devices. What if mlx5 will this in a much different way?
Adding Saeed as he will know. How does Mellanox set the number of
channels to 1 and how do you enable loopback mode? At least the rest
should be the same.
> > + sudo ethtool -K ${ETH} loopback on
> > + sudo ip link set ${ETH} promisc on
> > + sudo ip link set ${ETH} mtu ${MTU}
> > + sudo ip link set ${ETH} up
> > + IPV6_DISABLE_CMD="sudo sysctl -n net.ipv6.conf.${ETH}.disable_ipv6"
> > + IPV6_DISABLE=`$IPV6_DISABLE_CMD 2> /dev/null`
> > + [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=1
> > + sleep 1
> > +}
> > +
> > +cleanup_eth() {
> > + [[ $IPV6_DISABLE == "0" ]] && $IPV6_DISABLE_CMD=0
> > + sudo ethtool -K ${ETH} loopback off
> > + sudo ip link set ${ETH} promisc off
> > +}
> > +
> > if [ ! -z $ETH ]; then
> > VETH0=${ETH}
> > VETH1=${ETH}
> > + setup_eth
> > NS1=""
> > else
> > validate_root_exec
> > @@ -191,6 +214,8 @@ exec_xskxceiver
> >
> > if [ -z $ETH ]; then
> > cleanup_exit ${VETH0} ${VETH1} ${NS1}
> > +else
> > + cleanup_eth
> > fi
> >
> > failures=0
> > --
> > 2.34.1
> >
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-11-30 12:14 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2022-11-30 9:41 [PATCH bpf-next] selftests: xsk: changes for setting up NICs to run xsk self-tests Tirthendu Sarkar
2022-11-30 11:57 ` Maciej Fijalkowski
2022-11-30 12:13 ` Magnus Karlsson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).