[PATCH net] net: mdio-mux-meson-g12a: force internal PHY off on mux switch

[PATCH net] net: mdio-mux-meson-g12a: force internal PHY off on mux switch

[Jerome Brunet]

Force the internal PHY off then on when switching to the internal path.
This fixes problems where the PHY ID is not properly set.

Fixes: 7090425104db ("net: phy: add amlogic g12a mdio mux support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Co-developed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---

The initial discussion about this change can be found here:
https://lore.kernel.org/all/1j4jslwen5.fsf@starbuckisacylon.baylibre.com/

 drivers/net/mdio/mdio-mux-meson-g12a.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/net/mdio/mdio-mux-meson-g12a.c b/drivers/net/mdio/mdio-mux-meson-g12a.c
index 4a2e94faf57e..da61f00a6666 100644
--- a/drivers/net/mdio/mdio-mux-meson-g12a.c
+++ b/drivers/net/mdio/mdio-mux-meson-g12a.c
@@ -4,6 +4,7 @@
  */
 
 #include <linux/bitfield.h>
+#include <linux/delay.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/device.h>
@@ -151,6 +152,7 @@ static const struct clk_ops g12a_ephy_pll_ops = {
 static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
 {
 	int ret;
+	u32 value;
 
 	/* Enable the phy clock */
 	if (!priv->pll_is_enabled) {
@@ -163,18 +165,25 @@ static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
 
 	/* Initialize ephy control */
 	writel(EPHY_G12A_ID, priv->regs + ETH_PHY_CNTL0);
-	writel(FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
-	       FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
-	       FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
-	       PHY_CNTL1_CLK_EN |
-	       PHY_CNTL1_CLKFREQ |
-	       PHY_CNTL1_PHY_ENB,
-	       priv->regs + ETH_PHY_CNTL1);
+
+	/* Make sure we get a 0 -> 1 transition on the enable bit */
+	value = FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
+		FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
+		FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
+		PHY_CNTL1_CLK_EN |
+		PHY_CNTL1_CLKFREQ;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
 	writel(PHY_CNTL2_USE_INTERNAL |
 	       PHY_CNTL2_SMI_SRC_MAC |
 	       PHY_CNTL2_RX_CLK_EPHY,
 	       priv->regs + ETH_PHY_CNTL2);
 
+	value |= PHY_CNTL1_PHY_ENB;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
+
+	/* The phy needs a bit of time to power up */
+	mdelay(10);
+
 	return 0;
 }
 
-- 
2.39.0

Re: [PATCH net] net: mdio-mux-meson-g12a: force internal PHY off on mux switch

[Andrew Lunn]

On Mon, Jan 23, 2023 at 02:50:37PM +0100, Jerome Brunet wrote:
> Force the internal PHY off then on when switching to the internal path.
> This fixes problems where the PHY ID is not properly set.
> 
> Fixes: 7090425104db ("net: phy: add amlogic g12a mdio mux support")
> Suggested-by: Qi Duan <qi.duan@amlogic.com>
> Co-developed-by: Heiner Kallweit <hkallweit1@gmail.com>
> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> ---
> 
> The initial discussion about this change can be found here:
> https://lore.kernel.org/all/1j4jslwen5.fsf@starbuckisacylon.baylibre.com/
> 
>  drivers/net/mdio/mdio-mux-meson-g12a.c | 23 ++++++++++++++++-------
>  1 file changed, 16 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/net/mdio/mdio-mux-meson-g12a.c b/drivers/net/mdio/mdio-mux-meson-g12a.c
> index 4a2e94faf57e..da61f00a6666 100644
> --- a/drivers/net/mdio/mdio-mux-meson-g12a.c
> +++ b/drivers/net/mdio/mdio-mux-meson-g12a.c
> @@ -4,6 +4,7 @@
>   */
>  
>  #include <linux/bitfield.h>
> +#include <linux/delay.h>
>  #include <linux/clk.h>
>  #include <linux/clk-provider.h>
>  #include <linux/device.h>
> @@ -151,6 +152,7 @@ static const struct clk_ops g12a_ephy_pll_ops = {
>  static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
>  {
>  	int ret;
> +	u32 value;

Reverse Christmas tree please. Longest first, shortest last.

	Andrew