[Patch net-next v1 0/9] net: dsa: microchip: add support for phylink mac config and link up

[Patch net-next v1 0/9] net: dsa: microchip: add support for phylink mac config and link up

[Arun Ramadoss]

This patch series add support common phylink mac config and link up for the ksz
series switches. At present, ksz8795 and ksz9477 doesn't implement the phylink
mac config and link up. It configures the mac interface in the port setup hook.
ksz8830 series switch does not mac link configuration. For lan937x switches, in
the part support patch series has support only for MII and RMII configuration.
Some group of switches have some register address and bit fields common and
others are different. So, this patch aims to have common phylink implementation
which configures the register based on the chip id.

Changes in v1
- Squash the reading rgmii value from dt to patch which apply the rgmii value
- Created the new function ksz_port_set_xmii_speed
- Seperated the namespace values for xmii_ctrl_0 and xmii_ctrl_1 register
- Applied the rgmii delay value based on the rx/tx-internal-delay-ps

Arun Ramadoss (9):
  net: dsa: microchip: add common gigabit set and get function
  net: dsa: microchip: add common ksz port xmii speed selection function
  net: dsa: microchip: add common duplex and flow control function
  net: dsa: microchip: add support for common phylink mac link up
  net: dsa: microchip: lan937x: add support for configuing xMII register
  net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config
  net: dsa: microchip: ksz9477: use common xmii function
  net: dsa: microchip: ksz8795: use common xmii function
  net: dsa: microchip: add support for phylink mac config

 drivers/net/dsa/microchip/ksz8795.c      |  40 ---
 drivers/net/dsa/microchip/ksz8795_reg.h  |   8 -
 drivers/net/dsa/microchip/ksz9477.c      | 183 +-----------
 drivers/net/dsa/microchip/ksz9477_reg.h  |  24 --
 drivers/net/dsa/microchip/ksz_common.c   | 342 ++++++++++++++++++++++-
 drivers/net/dsa/microchip/ksz_common.h   |  46 +++
 drivers/net/dsa/microchip/lan937x.h      |   8 +-
 drivers/net/dsa/microchip/lan937x_main.c | 125 +++------
 drivers/net/dsa/microchip/lan937x_reg.h  |  32 ++-
 9 files changed, 453 insertions(+), 355 deletions(-)


base-commit: b66eb3a6e427b059101c6c92ac2ddd899014634c
-- 
2.36.1

[Patch net-next v1 1/9] net: dsa: microchip: add common gigabit set and get function

[Arun Ramadoss]

This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
---
 drivers/net/dsa/microchip/ksz9477.c      | 36 ++------------
 drivers/net/dsa/microchip/ksz9477_reg.h  |  4 --
 drivers/net/dsa/microchip/ksz_common.c   | 61 ++++++++++++++++++++++++
 drivers/net/dsa/microchip/ksz_common.h   | 12 +++++
 drivers/net/dsa/microchip/lan937x_main.c | 16 ++-----
 drivers/net/dsa/microchip/lan937x_reg.h  |  1 -
 6 files changed, 82 insertions(+), 48 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index 6453642fa14c..cfa7ddf60718 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -866,32 +866,6 @@ void ksz9477_port_mirror_del(struct ksz_device *dev, int port,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
-static bool ksz9477_get_gbit(struct ksz_device *dev, u8 data)
-{
-	bool gbit;
-
-	if (dev->features & NEW_XMII)
-		gbit = !(data & PORT_MII_NOT_1GBIT);
-	else
-		gbit = !!(data & PORT_MII_1000MBIT_S1);
-	return gbit;
-}
-
-static void ksz9477_set_gbit(struct ksz_device *dev, bool gbit, u8 *data)
-{
-	if (dev->features & NEW_XMII) {
-		if (gbit)
-			*data &= ~PORT_MII_NOT_1GBIT;
-		else
-			*data |= PORT_MII_NOT_1GBIT;
-	} else {
-		if (gbit)
-			*data |= PORT_MII_1000MBIT_S1;
-		else
-			*data &= ~PORT_MII_1000MBIT_S1;
-	}
-}
-
 static int ksz9477_get_xmii(struct ksz_device *dev, u8 data)
 {
 	int mode;
@@ -977,7 +951,7 @@ static phy_interface_t ksz9477_get_interface(struct ksz_device *dev, int port)
 	if (port < dev->phy_port_cnt)
 		return PHY_INTERFACE_MODE_NA;
 	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
-	gbit = ksz9477_get_gbit(dev, data8);
+	gbit = ksz_get_gbit(dev, port);
 	mode = ksz9477_get_xmii(dev, data8);
 	switch (mode) {
 	case 2:
@@ -1122,22 +1096,22 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 		switch (p->interface) {
 		case PHY_INTERFACE_MODE_MII:
 			ksz9477_set_xmii(dev, 0, &data8);
-			ksz9477_set_gbit(dev, false, &data8);
+			ksz_set_gbit(dev, port, false);
 			p->phydev.speed = SPEED_100;
 			break;
 		case PHY_INTERFACE_MODE_RMII:
 			ksz9477_set_xmii(dev, 1, &data8);
-			ksz9477_set_gbit(dev, false, &data8);
+			ksz_set_gbit(dev, port, false);
 			p->phydev.speed = SPEED_100;
 			break;
 		case PHY_INTERFACE_MODE_GMII:
 			ksz9477_set_xmii(dev, 2, &data8);
-			ksz9477_set_gbit(dev, true, &data8);
+			ksz_set_gbit(dev, port, true);
 			p->phydev.speed = SPEED_1000;
 			break;
 		default:
 			ksz9477_set_xmii(dev, 3, &data8);
-			ksz9477_set_gbit(dev, true, &data8);
+			ksz_set_gbit(dev, port, true);
 			data8 &= ~PORT_RGMII_ID_IG_ENABLE;
 			data8 &= ~PORT_RGMII_ID_EG_ENABLE;
 			if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index d0cce4ca3cf9..f23ed4809e47 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -1185,10 +1185,6 @@
 #define REG_PORT_XMII_CTRL_1		0x0301
 
 #define PORT_RMII_CLK_SEL		BIT(7)
-/* S1 */
-#define PORT_MII_1000MBIT_S1		BIT(6)
-/* S2 */
-#define PORT_MII_NOT_1GBIT		BIT(6)
 #define PORT_MII_SEL_EDGE		BIT(5)
 #define PORT_RGMII_ID_IG_ENABLE		BIT(4)
 #define PORT_RGMII_ID_EG_ENABLE		BIT(3)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index fd12a68c1dcd..343381102cbf 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -257,6 +257,7 @@ static const u16 ksz8795_regs[] = {
 	[S_START_CTRL]			= 0x01,
 	[S_BROADCAST_CTRL]		= 0x06,
 	[S_MULTICAST_CTRL]		= 0x04,
+	[P_XMII_CTRL_1]			= 0x56,
 };
 
 static const u32 ksz8795_masks[] = {
@@ -281,6 +282,11 @@ static const u32 ksz8795_masks[] = {
 	[DYNAMIC_MAC_TABLE_TIMESTAMP]	= GENMASK(28, 27),
 };
 
+static const u8 ksz8795_xmii_ctrl1[] = {
+	[P_GMII_1GBIT]			= 1,
+	[P_GMII_NOT_1GBIT]		= 0,
+};
+
 static const u8 ksz8795_shifts[] = {
 	[VLAN_TABLE_MEMBERSHIP_S]	= 7,
 	[VLAN_TABLE]			= 16,
@@ -351,6 +357,7 @@ static const u16 ksz9477_regs[] = {
 	[S_START_CTRL]			= 0x0300,
 	[S_BROADCAST_CTRL]		= 0x0332,
 	[S_MULTICAST_CTRL]		= 0x0331,
+	[P_XMII_CTRL_1]			= 0x0301,
 };
 
 static const u32 ksz9477_masks[] = {
@@ -362,6 +369,11 @@ static const u8 ksz9477_shifts[] = {
 	[ALU_STAT_INDEX]		= 16,
 };
 
+static const u8 ksz9477_xmii_ctrl1[] = {
+	[P_GMII_1GBIT]			= 0,
+	[P_GMII_NOT_1GBIT]		= 1,
+};
+
 static const u32 lan937x_masks[] = {
 	[ALU_STAT_WRITE]		= 1,
 	[ALU_STAT_READ]			= 2,
@@ -388,6 +400,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
 		.supports_rgmii = {false, false, false, false, true},
@@ -424,6 +437,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
 		.supports_rgmii = {false, false, false, false, true},
@@ -446,6 +460,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
 		.supports_rgmii = {false, false, false, false, true},
@@ -488,6 +503,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, false},
 		.supports_rmii	= {false, false, false, false,
@@ -514,6 +530,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, true},
 		.supports_rmii	= {false, false, false, false,
@@ -539,6 +556,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl1 = ksz8795_xmii_ctrl1, /* Same as ksz8795 */
 		.supports_mii = {false, false, true},
 		.supports_rmii = {false, false, true},
 		.supports_rgmii = {false, false, true},
@@ -561,6 +579,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, true},
 		.supports_rmii	= {false, false, false, false,
@@ -586,6 +605,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
 		.supports_rgmii = {false, false, false, false, true},
@@ -607,6 +627,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true, true},
 		.supports_rmii = {false, false, false, false, true, true},
 		.supports_rgmii = {false, false, false, false, true, true},
@@ -628,6 +649,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
 		.supports_rmii	= {false, false, false, false,
@@ -653,6 +675,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
 		.supports_rmii	= {false, false, false, false,
@@ -678,6 +701,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
 		.supports_rmii	= {false, false, false, false,
@@ -1353,6 +1377,43 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 		dev->dev_ops->phylink_mac_config(dev, port, mode, state);
 }
 
+bool ksz_get_gbit(struct ksz_device *dev, int port)
+{
+	const u8 *bitval = dev->info->xmii_ctrl1;
+	const u16 *regs = dev->info->regs;
+	bool gbit = false;
+	u8 data8;
+	bool val;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_1], &data8);
+
+	val = FIELD_GET(P_GMII_1GBIT_M, data8);
+
+	if (val == bitval[P_GMII_1GBIT])
+		gbit = true;
+
+	return gbit;
+}
+
+void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit)
+{
+	const u8 *bitval = dev->info->xmii_ctrl1;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_1], &data8);
+
+	data8 &= ~P_GMII_1GBIT_M;
+
+	if (gbit)
+		data8 |= FIELD_PREP(P_GMII_1GBIT_M, bitval[P_GMII_1GBIT]);
+	else
+		data8 |= FIELD_PREP(P_GMII_1GBIT_M, bitval[P_GMII_NOT_1GBIT]);
+
+	/* Write the updated value */
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_1], data8);
+}
+
 static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				    unsigned int mode,
 				    phy_interface_t interface,
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index d5dddb7ec045..22f03148be0b 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -51,6 +51,7 @@ struct ksz_chip_data {
 	const u16 *regs;
 	const u32 *masks;
 	const u8 *shifts;
+	const u8 *xmii_ctrl1;
 	int stp_ctrl_reg;
 	int broadcast_ctrl_reg;
 	int multicast_ctrl_reg;
@@ -169,6 +170,7 @@ enum ksz_regs {
 	S_START_CTRL,
 	S_BROADCAST_CTRL,
 	S_MULTICAST_CTRL,
+	P_XMII_CTRL_1,
 };
 
 enum ksz_masks {
@@ -208,6 +210,11 @@ enum ksz_shifts {
 	ALU_STAT_INDEX,
 };
 
+enum ksz_xmii_ctrl1 {
+	P_GMII_1GBIT,
+	P_GMII_NOT_1GBIT,
+};
+
 struct alu_struct {
 	/* entry 1 */
 	u8	is_static:1;
@@ -293,6 +300,8 @@ void ksz_switch_remove(struct ksz_device *dev);
 void ksz_init_mib_timer(struct ksz_device *dev);
 void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
+bool ksz_get_gbit(struct ksz_device *dev, int port);
+void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
@@ -456,6 +465,9 @@ static inline int is_lan937x(struct ksz_device *dev)
 
 #define SW_START			0x01
 
+/* xMII configuration */
+#define P_GMII_1GBIT_M			BIT(6)
+
 /* Regmap tables generation */
 #define KSZ_SPI_OP_RD		3
 #define KSZ_SPI_OP_WR		2
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index c29d175ca6f7..efca96b02e15 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -312,14 +312,6 @@ int lan937x_change_mtu(struct ksz_device *dev, int port, int new_mtu)
 	return 0;
 }
 
-static void lan937x_config_gbit(struct ksz_device *dev, bool gbit, u8 *data)
-{
-	if (gbit)
-		*data &= ~PORT_MII_NOT_1GBIT;
-	else
-		*data |= PORT_MII_NOT_1GBIT;
-}
-
 static void lan937x_mac_config(struct ksz_device *dev, int port,
 			       phy_interface_t interface)
 {
@@ -333,11 +325,11 @@ static void lan937x_mac_config(struct ksz_device *dev, int port,
 	/* configure MAC based on interface */
 	switch (interface) {
 	case PHY_INTERFACE_MODE_MII:
-		lan937x_config_gbit(dev, false, &data8);
+		ksz_set_gbit(dev, port, false);
 		data8 |= PORT_MII_SEL;
 		break;
 	case PHY_INTERFACE_MODE_RMII:
-		lan937x_config_gbit(dev, false, &data8);
+		ksz_set_gbit(dev, port, false);
 		data8 |= PORT_RMII_SEL;
 		break;
 	default:
@@ -363,9 +355,9 @@ static void lan937x_config_interface(struct ksz_device *dev, int port,
 			PORT_MII_TX_FLOW_CTRL | PORT_MII_RX_FLOW_CTRL);
 
 	if (speed == SPEED_1000)
-		lan937x_config_gbit(dev, true, &xmii_ctrl1);
+		ksz_set_gbit(dev, port, true);
 	else
-		lan937x_config_gbit(dev, false, &xmii_ctrl1);
+		ksz_set_gbit(dev, port, false);
 
 	if (speed == SPEED_100)
 		xmii_ctrl0 |= PORT_MII_100MBIT;
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
index c187d0a3e7fa..747295d34411 100644
--- a/drivers/net/dsa/microchip/lan937x_reg.h
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -140,7 +140,6 @@
 #define PORT_GRXC_ENABLE		BIT(0)
 
 #define REG_PORT_XMII_CTRL_1		0x0301
-#define PORT_MII_NOT_1GBIT		BIT(6)
 #define PORT_MII_SEL_EDGE		BIT(5)
 #define PORT_RGMII_ID_IG_ENABLE		BIT(4)
 #define PORT_RGMII_ID_EG_ENABLE		BIT(3)
-- 
2.36.1

[Patch net-next v1 2/9] net: dsa: microchip: add common ksz port xmii speed selection function

[Arun Ramadoss]

This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz9477_reg.h  |  1 -
 drivers/net/dsa/microchip/ksz_common.c   | 54 ++++++++++++++++++++++++
 drivers/net/dsa/microchip/ksz_common.h   | 10 +++++
 drivers/net/dsa/microchip/lan937x_main.c | 18 +++-----
 drivers/net/dsa/microchip/lan937x_reg.h  |  1 -
 5 files changed, 69 insertions(+), 15 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index f23ed4809e47..2649fdf0bae1 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -1179,7 +1179,6 @@
 
 #define PORT_SGMII_SEL			BIT(7)
 #define PORT_MII_FULL_DUPLEX		BIT(6)
-#define PORT_MII_100MBIT		BIT(4)
 #define PORT_GRXC_ENABLE		BIT(0)
 
 #define REG_PORT_XMII_CTRL_1		0x0301
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 343381102cbf..85392d3b1c2b 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -257,6 +257,7 @@ static const u16 ksz8795_regs[] = {
 	[S_START_CTRL]			= 0x01,
 	[S_BROADCAST_CTRL]		= 0x06,
 	[S_MULTICAST_CTRL]		= 0x04,
+	[P_XMII_CTRL_0]			= 0x06,
 	[P_XMII_CTRL_1]			= 0x56,
 };
 
@@ -282,6 +283,11 @@ static const u32 ksz8795_masks[] = {
 	[DYNAMIC_MAC_TABLE_TIMESTAMP]	= GENMASK(28, 27),
 };
 
+static const u8 ksz8795_xmii_ctrl0[] = {
+	[P_MII_100MBIT]			= 0,
+	[P_MII_10MBIT]			= 1,
+};
+
 static const u8 ksz8795_xmii_ctrl1[] = {
 	[P_GMII_1GBIT]			= 1,
 	[P_GMII_NOT_1GBIT]		= 0,
@@ -357,6 +363,7 @@ static const u16 ksz9477_regs[] = {
 	[S_START_CTRL]			= 0x0300,
 	[S_BROADCAST_CTRL]		= 0x0332,
 	[S_MULTICAST_CTRL]		= 0x0331,
+	[P_XMII_CTRL_0]			= 0x0300,
 	[P_XMII_CTRL_1]			= 0x0301,
 };
 
@@ -369,6 +376,11 @@ static const u8 ksz9477_shifts[] = {
 	[ALU_STAT_INDEX]		= 16,
 };
 
+static const u8 ksz9477_xmii_ctrl0[] = {
+	[P_MII_100MBIT]			= 1,
+	[P_MII_10MBIT]			= 0,
+};
+
 static const u8 ksz9477_xmii_ctrl1[] = {
 	[P_GMII_1GBIT]			= 0,
 	[P_GMII_NOT_1GBIT]		= 1,
@@ -400,6 +412,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl0 = ksz8795_xmii_ctrl0,
 		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
@@ -437,6 +450,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl0 = ksz8795_xmii_ctrl0,
 		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
@@ -460,6 +474,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz8795_regs,
 		.masks = ksz8795_masks,
 		.shifts = ksz8795_shifts,
+		.xmii_ctrl0 = ksz8795_xmii_ctrl0,
 		.xmii_ctrl1 = ksz8795_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
@@ -503,6 +518,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, false},
@@ -530,6 +546,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, true},
@@ -556,6 +573,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz8795_xmii_ctrl1, /* Same as ksz8795 */
 		.supports_mii = {false, false, true},
 		.supports_rmii = {false, false, true},
@@ -579,6 +597,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = ksz9477_masks,
 		.shifts = ksz9477_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   false, true, true},
@@ -605,6 +624,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true},
 		.supports_rmii = {false, false, false, false, true},
@@ -627,6 +647,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii = {false, false, false, false, true, true},
 		.supports_rmii = {false, false, false, false, true, true},
@@ -649,6 +670,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
@@ -675,6 +697,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
@@ -701,6 +724,7 @@ const struct ksz_chip_data ksz_switch_chips[] = {
 		.regs = ksz9477_regs,
 		.masks = lan937x_masks,
 		.shifts = lan937x_shifts,
+		.xmii_ctrl0 = ksz9477_xmii_ctrl0,
 		.xmii_ctrl1 = ksz9477_xmii_ctrl1,
 		.supports_mii	= {false, false, false, false,
 				   true, true, false, false},
@@ -1414,6 +1438,36 @@ void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit)
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_1], data8);
 }
 
+static void ksz_set_100_10mbit(struct ksz_device *dev, int port, int speed)
+{
+	const u8 *bitval = dev->info->xmii_ctrl0;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
+
+	data8 &= ~P_MII_100MBIT_M;
+
+	if (speed == SPEED_100)
+		data8 |= FIELD_PREP(P_MII_100MBIT_M, bitval[P_MII_100MBIT]);
+	else
+		data8 |= FIELD_PREP(P_MII_100MBIT_M, bitval[P_MII_10MBIT]);
+
+	/* Write the updated value */
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
+}
+
+void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed)
+{
+	if (speed == SPEED_1000)
+		ksz_set_gbit(dev, port, true);
+	else
+		ksz_set_gbit(dev, port, false);
+
+	if (speed == SPEED_100 || speed == SPEED_10)
+		ksz_set_100_10mbit(dev, port, speed);
+}
+
 static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				    unsigned int mode,
 				    phy_interface_t interface,
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 22f03148be0b..d87dc88d9f20 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -51,6 +51,7 @@ struct ksz_chip_data {
 	const u16 *regs;
 	const u32 *masks;
 	const u8 *shifts;
+	const u8 *xmii_ctrl0;
 	const u8 *xmii_ctrl1;
 	int stp_ctrl_reg;
 	int broadcast_ctrl_reg;
@@ -170,6 +171,7 @@ enum ksz_regs {
 	S_START_CTRL,
 	S_BROADCAST_CTRL,
 	S_MULTICAST_CTRL,
+	P_XMII_CTRL_0,
 	P_XMII_CTRL_1,
 };
 
@@ -210,6 +212,11 @@ enum ksz_shifts {
 	ALU_STAT_INDEX,
 };
 
+enum ksz_xmii_ctrl0 {
+	P_MII_100MBIT,
+	P_MII_10MBIT,
+};
+
 enum ksz_xmii_ctrl1 {
 	P_GMII_1GBIT,
 	P_GMII_NOT_1GBIT,
@@ -302,6 +309,7 @@ void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
 void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
+void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
@@ -466,6 +474,8 @@ static inline int is_lan937x(struct ksz_device *dev)
 #define SW_START			0x01
 
 /* xMII configuration */
+#define P_MII_100MBIT_M			BIT(4)
+
 #define P_GMII_1GBIT_M			BIT(6)
 
 /* Regmap tables generation */
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index efca96b02e15..c48bae285758 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -346,21 +346,14 @@ static void lan937x_config_interface(struct ksz_device *dev, int port,
 				     int speed, int duplex,
 				     bool tx_pause, bool rx_pause)
 {
-	u8 xmii_ctrl0, xmii_ctrl1;
+	u8 xmii_ctrl0;
 
-	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_0, &xmii_ctrl0);
-	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &xmii_ctrl1);
-
-	xmii_ctrl0 &= ~(PORT_MII_100MBIT | PORT_MII_FULL_DUPLEX |
-			PORT_MII_TX_FLOW_CTRL | PORT_MII_RX_FLOW_CTRL);
+	ksz_port_set_xmii_speed(dev, port, speed);
 
-	if (speed == SPEED_1000)
-		ksz_set_gbit(dev, port, true);
-	else
-		ksz_set_gbit(dev, port, false);
+	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_0, &xmii_ctrl0);
 
-	if (speed == SPEED_100)
-		xmii_ctrl0 |= PORT_MII_100MBIT;
+	xmii_ctrl0 &= ~(PORT_MII_FULL_DUPLEX | PORT_MII_TX_FLOW_CTRL |
+			PORT_MII_RX_FLOW_CTRL);
 
 	if (duplex)
 		xmii_ctrl0 |= PORT_MII_FULL_DUPLEX;
@@ -372,7 +365,6 @@ static void lan937x_config_interface(struct ksz_device *dev, int port,
 		xmii_ctrl0 |= PORT_MII_RX_FLOW_CTRL;
 
 	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_0, xmii_ctrl0);
-	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, xmii_ctrl1);
 }
 
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
index 747295d34411..b9364f6a4f8f 100644
--- a/drivers/net/dsa/microchip/lan937x_reg.h
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -135,7 +135,6 @@
 #define PORT_SGMII_SEL			BIT(7)
 #define PORT_MII_FULL_DUPLEX		BIT(6)
 #define PORT_MII_TX_FLOW_CTRL		BIT(5)
-#define PORT_MII_100MBIT		BIT(4)
 #define PORT_MII_RX_FLOW_CTRL		BIT(3)
 #define PORT_GRXC_ENABLE		BIT(0)
 
-- 
2.36.1

[Patch net-next v1 3/9] net: dsa: microchip: add common duplex and flow control function

[Arun Ramadoss]

This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz9477_reg.h  |  1 -
 drivers/net/dsa/microchip/ksz_common.c   | 62 ++++++++++++++++++++++++
 drivers/net/dsa/microchip/ksz_common.h   |  8 +++
 drivers/net/dsa/microchip/lan937x_main.c | 24 +++------
 drivers/net/dsa/microchip/lan937x_reg.h  |  3 --
 5 files changed, 78 insertions(+), 20 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index 2649fdf0bae1..6ca859345932 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -1178,7 +1178,6 @@
 #define REG_PORT_XMII_CTRL_0		0x0300
 
 #define PORT_SGMII_SEL			BIT(7)
-#define PORT_MII_FULL_DUPLEX		BIT(6)
 #define PORT_GRXC_ENABLE		BIT(0)
 
 #define REG_PORT_XMII_CTRL_1		0x0301
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 85392d3b1c2b..16825fcf43a8 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -281,11 +281,15 @@ static const u32 ksz8795_masks[] = {
 	[DYNAMIC_MAC_TABLE_FID]		= GENMASK(26, 20),
 	[DYNAMIC_MAC_TABLE_SRC_PORT]	= GENMASK(26, 24),
 	[DYNAMIC_MAC_TABLE_TIMESTAMP]	= GENMASK(28, 27),
+	[P_MII_TX_FLOW_CTRL]		= BIT(5),
+	[P_MII_RX_FLOW_CTRL]		= BIT(5),
 };
 
 static const u8 ksz8795_xmii_ctrl0[] = {
 	[P_MII_100MBIT]			= 0,
 	[P_MII_10MBIT]			= 1,
+	[P_MII_FULL_DUPLEX]		= 0,
+	[P_MII_HALF_DUPLEX]		= 1,
 };
 
 static const u8 ksz8795_xmii_ctrl1[] = {
@@ -370,6 +374,8 @@ static const u16 ksz9477_regs[] = {
 static const u32 ksz9477_masks[] = {
 	[ALU_STAT_WRITE]		= 0,
 	[ALU_STAT_READ]			= 1,
+	[P_MII_TX_FLOW_CTRL]		= BIT(5),
+	[P_MII_RX_FLOW_CTRL]		= BIT(3),
 };
 
 static const u8 ksz9477_shifts[] = {
@@ -379,6 +385,8 @@ static const u8 ksz9477_shifts[] = {
 static const u8 ksz9477_xmii_ctrl0[] = {
 	[P_MII_100MBIT]			= 1,
 	[P_MII_10MBIT]			= 0,
+	[P_MII_FULL_DUPLEX]		= 1,
+	[P_MII_HALF_DUPLEX]		= 0,
 };
 
 static const u8 ksz9477_xmii_ctrl1[] = {
@@ -389,6 +397,8 @@ static const u8 ksz9477_xmii_ctrl1[] = {
 static const u32 lan937x_masks[] = {
 	[ALU_STAT_WRITE]		= 1,
 	[ALU_STAT_READ]			= 2,
+	[P_MII_TX_FLOW_CTRL]		= BIT(5),
+	[P_MII_RX_FLOW_CTRL]		= BIT(3),
 };
 
 static const u8 lan937x_shifts[] = {
@@ -1468,6 +1478,58 @@ void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed)
 		ksz_set_100_10mbit(dev, port, speed);
 }
 
+void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val)
+{
+	const u8 *bitval = dev->info->xmii_ctrl0;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
+
+	data8 &= ~P_MII_DUPLEX_M;
+
+	if (val)
+		data8 |= FIELD_PREP(P_MII_DUPLEX_M,
+				    bitval[P_MII_FULL_DUPLEX]);
+	else
+		data8 |= FIELD_PREP(P_MII_DUPLEX_M,
+				    bitval[P_MII_HALF_DUPLEX]);
+
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
+}
+
+void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val)
+{
+	const u32 *masks = dev->info->masks;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
+
+	if (val)
+		data8 |= masks[P_MII_TX_FLOW_CTRL];
+	else
+		data8 &= ~masks[P_MII_TX_FLOW_CTRL];
+
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
+}
+
+void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val)
+{
+	const u32 *masks = dev->info->masks;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
+
+	if (val)
+		data8 |= masks[P_MII_RX_FLOW_CTRL];
+	else
+		data8 &= ~masks[P_MII_RX_FLOW_CTRL];
+
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
+}
+
 static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				    unsigned int mode,
 				    phy_interface_t interface,
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index d87dc88d9f20..df8759dc02bd 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -197,6 +197,8 @@ enum ksz_masks {
 	DYNAMIC_MAC_TABLE_TIMESTAMP,
 	ALU_STAT_WRITE,
 	ALU_STAT_READ,
+	P_MII_TX_FLOW_CTRL,
+	P_MII_RX_FLOW_CTRL,
 };
 
 enum ksz_shifts {
@@ -215,6 +217,8 @@ enum ksz_shifts {
 enum ksz_xmii_ctrl0 {
 	P_MII_100MBIT,
 	P_MII_10MBIT,
+	P_MII_FULL_DUPLEX,
+	P_MII_HALF_DUPLEX,
 };
 
 enum ksz_xmii_ctrl1 {
@@ -310,6 +314,9 @@ void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
 void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
 void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed);
+void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val);
+void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val);
+void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
@@ -474,6 +481,7 @@ static inline int is_lan937x(struct ksz_device *dev)
 #define SW_START			0x01
 
 /* xMII configuration */
+#define P_MII_DUPLEX_M			BIT(6)
 #define P_MII_100MBIT_M			BIT(4)
 
 #define P_GMII_1GBIT_M			BIT(6)
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index c48bae285758..92275064fa6b 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -234,6 +234,8 @@ int lan937x_reset_switch(struct ksz_device *dev)
 
 void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 {
+	const u32 *masks = dev->info->masks;
+	const u16 *regs = dev->info->regs;
 	struct dsa_switch *ds = dev->ds;
 	u8 member;
 
@@ -254,8 +256,9 @@ void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 	lan937x_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true);
 
 	if (!dev->info->internal_phy[port])
-		lan937x_port_cfg(dev, port, REG_PORT_XMII_CTRL_0,
-				 PORT_MII_TX_FLOW_CTRL | PORT_MII_RX_FLOW_CTRL,
+		lan937x_port_cfg(dev, port, regs[P_XMII_CTRL_0],
+				 masks[P_MII_TX_FLOW_CTRL] |
+				 masks[P_MII_RX_FLOW_CTRL],
 				 true);
 
 	if (cpu_port)
@@ -346,25 +349,14 @@ static void lan937x_config_interface(struct ksz_device *dev, int port,
 				     int speed, int duplex,
 				     bool tx_pause, bool rx_pause)
 {
-	u8 xmii_ctrl0;
-
 	ksz_port_set_xmii_speed(dev, port, speed);
 
-	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_0, &xmii_ctrl0);
-
-	xmii_ctrl0 &= ~(PORT_MII_FULL_DUPLEX | PORT_MII_TX_FLOW_CTRL |
-			PORT_MII_RX_FLOW_CTRL);
-
-	if (duplex)
-		xmii_ctrl0 |= PORT_MII_FULL_DUPLEX;
+	ksz_set_fullduplex(dev, port, duplex);
 
-	if (tx_pause)
-		xmii_ctrl0 |= PORT_MII_TX_FLOW_CTRL;
+	ksz_set_tx_pause(dev, port, tx_pause);
 
-	if (rx_pause)
-		xmii_ctrl0 |= PORT_MII_RX_FLOW_CTRL;
+	ksz_set_rx_pause(dev, port, rx_pause);
 
-	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_0, xmii_ctrl0);
 }
 
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
index b9364f6a4f8f..d5eb6dc3a739 100644
--- a/drivers/net/dsa/microchip/lan937x_reg.h
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -133,9 +133,6 @@
 /* 3 - xMII */
 #define REG_PORT_XMII_CTRL_0		0x0300
 #define PORT_SGMII_SEL			BIT(7)
-#define PORT_MII_FULL_DUPLEX		BIT(6)
-#define PORT_MII_TX_FLOW_CTRL		BIT(5)
-#define PORT_MII_RX_FLOW_CTRL		BIT(3)
 #define PORT_GRXC_ENABLE		BIT(0)
 
 #define REG_PORT_XMII_CTRL_1		0x0301
-- 
2.36.1

Re: [Patch net-next v1 3/9] net: dsa: microchip: add common duplex and flow control function

[Russell King (Oracle)]

Hi,

On Fri, Jul 22, 2022 at 02:54:53PM +0530, Arun Ramadoss wrote:
> +void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val)
> +{
> +	const u8 *bitval = dev->info->xmii_ctrl0;
> +	const u16 *regs = dev->info->regs;
> +	u8 data8;
> +
> +	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
> +
> +	data8 &= ~P_MII_DUPLEX_M;
> +
> +	if (val)
> +		data8 |= FIELD_PREP(P_MII_DUPLEX_M,
> +				    bitval[P_MII_FULL_DUPLEX]);
> +	else
> +		data8 |= FIELD_PREP(P_MII_DUPLEX_M,
> +				    bitval[P_MII_HALF_DUPLEX]);
> +
> +	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
> +}
> +
> +void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val)
> +{
> +	const u32 *masks = dev->info->masks;
> +	const u16 *regs = dev->info->regs;
> +	u8 data8;
> +
> +	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
> +
> +	if (val)
> +		data8 |= masks[P_MII_TX_FLOW_CTRL];
> +	else
> +		data8 &= ~masks[P_MII_TX_FLOW_CTRL];
> +
> +	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
> +}
> +
> +void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val)
> +{
> +	const u32 *masks = dev->info->masks;
> +	const u16 *regs = dev->info->regs;
> +	u8 data8;
> +
> +	ksz_pread8(dev, port, regs[P_XMII_CTRL_0], &data8);
> +
> +	if (val)
> +		data8 |= masks[P_MII_RX_FLOW_CTRL];
> +	else
> +		data8 &= ~masks[P_MII_RX_FLOW_CTRL];
> +
> +	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
> +}
> +

Having looked through all the proposed patches and noticed that these
three functions are always called serially. What is the reason to make
these separate functions which all read the same register, modify a
single bit, and then write it back.

What we end up with is the following sequence:

- read P_XMII_CTRL_0
- udpate P_MII_HALF_DUPLEX bit
- write P_XMII_CTRL_0
- read P_XMII_CTRL_0
- update P_MII_TX_FLOW_CTRL bit
- write P_XMII_CTRL_0
- read P_XMII_CTRL_0
- update P_MII_RX_FLOW_CTRL bit
- write P_XMII_CTRL_0

whereas the original code did:

- read P_XMII_CTRL_0
- udpate P_MII_HALF_DUPLEX, P_MII_TX_FLOW_CTRL and P_MII_RX_FLOW_CTRL
  bits
- write P_XMII_CTRL_0

which was much more efficient, not only in terms of CPU cycles, but also
IO cycles and code size.

You could do this instead:

	u8 mask, val, ctrl0;

	mask = P_MII_DUPLEX_M | masks[P_MII_TX_FLOW_CTRL] |
	       masks[P_MII_RX_FLOW_CTRL];

	if (duplex == DUPLEX_FULL)
		val = FIELD_PREP(P_MII_DUPLEX_M, bitval[P_MII_FULL_DUPLEX]);
	else
		val = FIELD_PREP(P_MII_DUPLEX_M, bitval[P_MII_HALF_DUPLEX]);

	if (tx_pause)
		val |= masks[P_MII_TX_FLOW_CTRL];
	
	if (rx_pause)
		val |= masks[P_MII_RX_FLOW_CTRL];
	
	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_0, &ctrl0);
	ctrl0 = (ctrl0 & ~mask) | val;
	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_0, ctrl0);

and maybe convert that last three lines into a helper, ksz_pmodify8()
which could be useful in other parts of the driver where you do a
read-modify-write operation on a register.

Thanks.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

[Patch net-next v1 4/9] net: dsa: microchip: add support for common phylink mac link up

[Arun Ramadoss]

This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz_common.c   | 26 ++++++++++++++++++-----
 drivers/net/dsa/microchip/ksz_common.h   |  4 ----
 drivers/net/dsa/microchip/lan937x.h      |  4 ----
 drivers/net/dsa/microchip/lan937x_main.c | 27 ------------------------
 4 files changed, 21 insertions(+), 40 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 16825fcf43a8..91d620559f2e 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -223,7 +223,6 @@ static const struct ksz_dev_ops lan937x_dev_ops = {
 	.mirror_del = ksz9477_port_mirror_del,
 	.get_caps = lan937x_phylink_get_caps,
 	.phylink_mac_config = lan937x_phylink_mac_config,
-	.phylink_mac_link_up = lan937x_phylink_mac_link_up,
 	.fdb_dump = ksz9477_fdb_dump,
 	.fdb_add = ksz9477_fdb_add,
 	.fdb_del = ksz9477_fdb_del,
@@ -1467,7 +1466,7 @@ static void ksz_set_100_10mbit(struct ksz_device *dev, int port, int speed)
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
 }
 
-void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed)
+static void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed)
 {
 	if (speed == SPEED_1000)
 		ksz_set_gbit(dev, port, true);
@@ -1478,7 +1477,7 @@ void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed)
 		ksz_set_100_10mbit(dev, port, speed);
 }
 
-void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val)
+static void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val)
 {
 	const u8 *bitval = dev->info->xmii_ctrl0;
 	const u16 *regs = dev->info->regs;
@@ -1498,7 +1497,7 @@ void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val)
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
 }
 
-void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val)
+static void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val)
 {
 	const u32 *masks = dev->info->masks;
 	const u16 *regs = dev->info->regs;
@@ -1514,7 +1513,7 @@ void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val)
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_0], data8);
 }
 
-void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val)
+static void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val)
 {
 	const u32 *masks = dev->info->masks;
 	const u16 *regs = dev->info->regs;
@@ -1537,6 +1536,23 @@ static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				    int duplex, bool tx_pause, bool rx_pause)
 {
 	struct ksz_device *dev = ds->priv;
+	struct ksz_port *p;
+
+	p = &dev->ports[port];
+
+	/* Internal PHYs */
+	if (dev->info->internal_phy[port])
+		return;
+
+	p->phydev.speed = speed;
+
+	ksz_port_set_xmii_speed(dev, port, speed);
+
+	ksz_set_fullduplex(dev, port, duplex);
+
+	ksz_set_tx_pause(dev, port, tx_pause);
+
+	ksz_set_rx_pause(dev, port, rx_pause);
 
 	if (dev->dev_ops->phylink_mac_link_up)
 		dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface,
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index df8759dc02bd..d386f07cb711 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -313,10 +313,6 @@ void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
 void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
-void ksz_port_set_xmii_speed(struct ksz_device *dev, int port, int speed);
-void ksz_set_fullduplex(struct ksz_device *dev, int port, bool val);
-void ksz_set_tx_pause(struct ksz_device *dev, int port, bool val);
-void ksz_set_rx_pause(struct ksz_device *dev, int port, bool val);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
diff --git a/drivers/net/dsa/microchip/lan937x.h b/drivers/net/dsa/microchip/lan937x.h
index 72ba9cb2fbc6..0ae553a9b9af 100644
--- a/drivers/net/dsa/microchip/lan937x.h
+++ b/drivers/net/dsa/microchip/lan937x.h
@@ -17,10 +17,6 @@ void lan937x_w_phy(struct ksz_device *dev, u16 addr, u16 reg, u16 val);
 int lan937x_change_mtu(struct ksz_device *dev, int port, int new_mtu);
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 			      struct phylink_config *config);
-void lan937x_phylink_mac_link_up(struct ksz_device *dev, int port,
-				 unsigned int mode, phy_interface_t interface,
-				 struct phy_device *phydev, int speed,
-				 int duplex, bool tx_pause, bool rx_pause);
 void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
 				unsigned int mode,
 				const struct phylink_link_state *state);
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index 92275064fa6b..a2e648eacd19 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -345,20 +345,6 @@ static void lan937x_mac_config(struct ksz_device *dev, int port,
 	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
 }
 
-static void lan937x_config_interface(struct ksz_device *dev, int port,
-				     int speed, int duplex,
-				     bool tx_pause, bool rx_pause)
-{
-	ksz_port_set_xmii_speed(dev, port, speed);
-
-	ksz_set_fullduplex(dev, port, duplex);
-
-	ksz_set_tx_pause(dev, port, tx_pause);
-
-	ksz_set_rx_pause(dev, port, rx_pause);
-
-}
-
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 			      struct phylink_config *config)
 {
@@ -371,19 +357,6 @@ void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 	}
 }
 
-void lan937x_phylink_mac_link_up(struct ksz_device *dev, int port,
-				 unsigned int mode, phy_interface_t interface,
-				 struct phy_device *phydev, int speed,
-				 int duplex, bool tx_pause, bool rx_pause)
-{
-	/* Internal PHYs */
-	if (dev->info->internal_phy[port])
-		return;
-
-	lan937x_config_interface(dev, port, speed, duplex,
-				 tx_pause, rx_pause);
-}
-
 void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
 				unsigned int mode,
 				const struct phylink_link_state *state)
-- 
2.36.1

[Patch net-next v1 5/9] net: dsa: microchip: lan937x: add support for configuing xMII register

[Arun Ramadoss]

This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz_common.c   | 44 ++++++++++++++++++++++++
 drivers/net/dsa/microchip/ksz_common.h   |  8 +++++
 drivers/net/dsa/microchip/lan937x_main.c | 32 +----------------
 drivers/net/dsa/microchip/lan937x_reg.h  |  9 -----
 4 files changed, 53 insertions(+), 40 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 91d620559f2e..2ba6ec09b6af 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -292,6 +292,10 @@ static const u8 ksz8795_xmii_ctrl0[] = {
 };
 
 static const u8 ksz8795_xmii_ctrl1[] = {
+	[P_RGMII_SEL]			= 3,
+	[P_GMII_SEL]			= 2,
+	[P_RMII_SEL]			= 1,
+	[P_MII_SEL]			= 0,
 	[P_GMII_1GBIT]			= 1,
 	[P_GMII_NOT_1GBIT]		= 0,
 };
@@ -389,6 +393,10 @@ static const u8 ksz9477_xmii_ctrl0[] = {
 };
 
 static const u8 ksz9477_xmii_ctrl1[] = {
+	[P_RGMII_SEL]			= 0,
+	[P_RMII_SEL]			= 1,
+	[P_GMII_SEL]			= 2,
+	[P_MII_SEL]			= 3,
 	[P_GMII_1GBIT]			= 0,
 	[P_GMII_NOT_1GBIT]		= 1,
 };
@@ -1400,6 +1408,42 @@ static int ksz_max_mtu(struct dsa_switch *ds, int port)
 	return dev->dev_ops->max_mtu(dev, port);
 }
 
+void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
+{
+	const u8 *bitval = dev->info->xmii_ctrl1;
+	const u16 *regs = dev->info->regs;
+	u8 data8;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_1], &data8);
+
+	data8 &= ~P_MII_SEL_M;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_MII:
+		data8 |= bitval[P_MII_SEL];
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		data8 |= bitval[P_RMII_SEL];
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		data8 |= bitval[P_GMII_SEL];
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		data8 |= bitval[P_RGMII_SEL];
+		break;
+	default:
+		dev_err(dev->dev, "Unsupported interface '%s' for port %d\n",
+			phy_modes(interface), port);
+		return;
+	}
+
+	/* Write the updated value */
+	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_1], data8);
+}
+
 static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 				   unsigned int mode,
 				   const struct phylink_link_state *state)
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index d386f07cb711..a69aff079cd9 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -222,6 +222,10 @@ enum ksz_xmii_ctrl0 {
 };
 
 enum ksz_xmii_ctrl1 {
+	P_RGMII_SEL,
+	P_RMII_SEL,
+	P_GMII_SEL,
+	P_MII_SEL,
 	P_GMII_1GBIT,
 	P_GMII_NOT_1GBIT,
 };
@@ -313,6 +317,7 @@ void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
 void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
+void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
@@ -481,6 +486,9 @@ static inline int is_lan937x(struct ksz_device *dev)
 #define P_MII_100MBIT_M			BIT(4)
 
 #define P_GMII_1GBIT_M			BIT(6)
+#define P_RGMII_ID_IG_ENABLE		BIT(4)
+#define P_RGMII_ID_EG_ENABLE		BIT(3)
+#define P_MII_SEL_M			0x3
 
 /* Regmap tables generation */
 #define KSZ_SPI_OP_RD		3
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index a2e648eacd19..d86ffdf976b0 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -315,36 +315,6 @@ int lan937x_change_mtu(struct ksz_device *dev, int port, int new_mtu)
 	return 0;
 }
 
-static void lan937x_mac_config(struct ksz_device *dev, int port,
-			       phy_interface_t interface)
-{
-	u8 data8;
-
-	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
-
-	/* clear MII selection & set it based on interface later */
-	data8 &= ~PORT_MII_SEL_M;
-
-	/* configure MAC based on interface */
-	switch (interface) {
-	case PHY_INTERFACE_MODE_MII:
-		ksz_set_gbit(dev, port, false);
-		data8 |= PORT_MII_SEL;
-		break;
-	case PHY_INTERFACE_MODE_RMII:
-		ksz_set_gbit(dev, port, false);
-		data8 |= PORT_RMII_SEL;
-		break;
-	default:
-		dev_err(dev->dev, "Unsupported interface '%s' for port %d\n",
-			phy_modes(interface), port);
-		return;
-	}
-
-	/* Write the updated value */
-	ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
-}
-
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 			      struct phylink_config *config)
 {
@@ -370,7 +340,7 @@ void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
 		return;
 	}
 
-	lan937x_mac_config(dev, port, state->interface);
+	ksz_set_xmii(dev, port, state->interface);
 }
 
 int lan937x_setup(struct dsa_switch *ds)
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
index d5eb6dc3a739..a6cb3ca22dc3 100644
--- a/drivers/net/dsa/microchip/lan937x_reg.h
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -131,19 +131,10 @@
 #define REG_PORT_T1_PHY_CTRL_BASE	0x0100
 
 /* 3 - xMII */
-#define REG_PORT_XMII_CTRL_0		0x0300
 #define PORT_SGMII_SEL			BIT(7)
 #define PORT_GRXC_ENABLE		BIT(0)
 
-#define REG_PORT_XMII_CTRL_1		0x0301
 #define PORT_MII_SEL_EDGE		BIT(5)
-#define PORT_RGMII_ID_IG_ENABLE		BIT(4)
-#define PORT_RGMII_ID_EG_ENABLE		BIT(3)
-#define PORT_MII_MAC_MODE		BIT(2)
-#define PORT_MII_SEL_M			0x3
-#define PORT_RGMII_SEL			0x0
-#define PORT_RMII_SEL			0x1
-#define PORT_MII_SEL			0x2
 
 /* 4 - MAC */
 #define REG_PORT_MAC_CTRL_0		0x0400
-- 
2.36.1

[Patch net-next v1 6/9] net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config

[Arun Ramadoss]

This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port.  It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz_common.c   | 53 +++++++++++++++++++++-
 drivers/net/dsa/microchip/ksz_common.h   |  3 ++
 drivers/net/dsa/microchip/lan937x.h      |  1 +
 drivers/net/dsa/microchip/lan937x_main.c | 56 ++++++++++++++++++++++++
 drivers/net/dsa/microchip/lan937x_reg.h  | 18 ++++++++
 5 files changed, 130 insertions(+), 1 deletion(-)

diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 2ba6ec09b6af..65a4ed77f3cc 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -223,6 +223,7 @@ static const struct ksz_dev_ops lan937x_dev_ops = {
 	.mirror_del = ksz9477_port_mirror_del,
 	.get_caps = lan937x_phylink_get_caps,
 	.phylink_mac_config = lan937x_phylink_mac_config,
+	.setup_rgmii_delay = lan937x_setup_rgmii_delay,
 	.fdb_dump = ksz9477_fdb_dump,
 	.fdb_add = ksz9477_fdb_add,
 	.fdb_del = ksz9477_fdb_del,
@@ -1411,12 +1412,14 @@ static int ksz_max_mtu(struct dsa_switch *ds, int port)
 void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
 {
 	const u8 *bitval = dev->info->xmii_ctrl1;
+	struct ksz_port *p = &dev->ports[port];
 	const u16 *regs = dev->info->regs;
 	u8 data8;
 
 	ksz_pread8(dev, port, regs[P_XMII_CTRL_1], &data8);
 
-	data8 &= ~P_MII_SEL_M;
+	data8 &= ~(P_MII_SEL_M | P_RGMII_ID_IG_ENABLE |
+		   P_RGMII_ID_EG_ENABLE);
 
 	switch (interface) {
 	case PHY_INTERFACE_MODE_MII:
@@ -1440,6 +1443,12 @@ void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
 		return;
 	}
 
+	if (p->rgmii_tx_val)
+		data8 |= P_RGMII_ID_EG_ENABLE;
+
+	if (p->rgmii_rx_val)
+		data8 |= P_RGMII_ID_IG_ENABLE;
+
 	/* Write the updated value */
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_1], data8);
 }
@@ -1452,6 +1461,9 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 
 	if (dev->dev_ops->phylink_mac_config)
 		dev->dev_ops->phylink_mac_config(dev, port, mode, state);
+
+	if (dev->dev_ops->setup_rgmii_delay)
+		dev->dev_ops->setup_rgmii_delay(dev, port);
 }
 
 bool ksz_get_gbit(struct ksz_device *dev, int port)
@@ -1731,6 +1743,43 @@ struct ksz_device *ksz_switch_alloc(struct device *base, void *priv)
 }
 EXPORT_SYMBOL(ksz_switch_alloc);
 
+static void ksz_parse_rgmii_delay(struct ksz_device *dev, int port_num,
+				  struct device_node *port_dn)
+{
+	phy_interface_t phy_mode = dev->ports[port_num].interface;
+	int rx_delay = -1, tx_delay = -1;
+
+	if (!phy_interface_mode_is_rgmii(phy_mode))
+		return;
+
+	of_property_read_u32(port_dn, "rx-internal-delay-ps", &rx_delay);
+	of_property_read_u32(port_dn, "tx-internal-delay-ps", &tx_delay);
+
+	if (rx_delay == -1 && tx_delay == -1) {
+		dev_warn(dev->dev,
+			 "Port %d interpreting RGMII delay settings based on \"phy-mode\" property, "
+			 "please update device tree to specify \"rx-internal-delay-ps\" and "
+			 "\"tx-internal-delay-ps\"",
+			 port_num);
+
+		if (phy_mode == PHY_INTERFACE_MODE_RGMII_RXID ||
+		    phy_mode == PHY_INTERFACE_MODE_RGMII_ID)
+			rx_delay = 2000;
+
+		if (phy_mode == PHY_INTERFACE_MODE_RGMII_TXID ||
+		    phy_mode == PHY_INTERFACE_MODE_RGMII_ID)
+			tx_delay = 2000;
+	}
+
+	if (rx_delay < 0)
+		rx_delay = 0;
+	if (tx_delay < 0)
+		tx_delay = 0;
+
+	dev->ports[port_num].rgmii_rx_val = rx_delay;
+	dev->ports[port_num].rgmii_tx_val = tx_delay;
+}
+
 int ksz_switch_register(struct ksz_device *dev)
 {
 	const struct ksz_chip_data *info;
@@ -1828,6 +1877,8 @@ int ksz_switch_register(struct ksz_device *dev)
 				}
 				of_get_phy_mode(port,
 						&dev->ports[port_num].interface);
+
+				ksz_parse_rgmii_delay(dev, port_num, port);
 			}
 			of_node_put(ports);
 		}
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index a69aff079cd9..61942e0636d6 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -79,6 +79,8 @@ struct ksz_port {
 	struct ksz_port_mib mib;
 	phy_interface_t interface;
 	u16 max_frame;
+	u32 rgmii_tx_val;
+	u32 rgmii_rx_val;
 };
 
 struct ksz_device {
@@ -301,6 +303,7 @@ struct ksz_dev_ops {
 				    phy_interface_t interface,
 				    struct phy_device *phydev, int speed,
 				    int duplex, bool tx_pause, bool rx_pause);
+	void (*setup_rgmii_delay)(struct ksz_device *dev, int port);
 	void (*config_cpu_port)(struct dsa_switch *ds);
 	int (*enable_stp_addr)(struct ksz_device *dev);
 	int (*reset)(struct ksz_device *dev);
diff --git a/drivers/net/dsa/microchip/lan937x.h b/drivers/net/dsa/microchip/lan937x.h
index 0ae553a9b9af..423521a13c9e 100644
--- a/drivers/net/dsa/microchip/lan937x.h
+++ b/drivers/net/dsa/microchip/lan937x.h
@@ -20,4 +20,5 @@ void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
 				unsigned int mode,
 				const struct phylink_link_state *state);
+void lan937x_setup_rgmii_delay(struct ksz_device *dev, int port);
 #endif
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index d86ffdf976b0..797fe7f62394 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -315,6 +315,45 @@ int lan937x_change_mtu(struct ksz_device *dev, int port, int new_mtu)
 	return 0;
 }
 
+static void lan937x_set_tune_adj(struct ksz_device *dev, int port,
+				 u16 reg, u8 val)
+{
+	u16 data16;
+
+	ksz_pread16(dev, port, reg, &data16);
+
+	/* Update tune Adjust */
+	data16 |= FIELD_PREP(PORT_TUNE_ADJ, val);
+	ksz_pwrite16(dev, port, reg, data16);
+
+	/* write DLL reset to take effect */
+	data16 |= PORT_DLL_RESET;
+	ksz_pwrite16(dev, port, reg, data16);
+}
+
+static void lan937x_set_rgmii_tx_delay(struct ksz_device *dev, int port)
+{
+	u8 val;
+
+	/* Apply different codes based on the ports as per characterization
+	 * results
+	 */
+	val = (port == LAN937X_RGMII_1_PORT) ? RGMII_1_TX_DELAY_2NS :
+		RGMII_2_TX_DELAY_2NS;
+
+	lan937x_set_tune_adj(dev, port, REG_PORT_XMII_CTRL_5, val);
+}
+
+static void lan937x_set_rgmii_rx_delay(struct ksz_device *dev, int port)
+{
+	u8 val;
+
+	val = (port == LAN937X_RGMII_1_PORT) ? RGMII_1_RX_DELAY_2NS :
+		RGMII_2_RX_DELAY_2NS;
+
+	lan937x_set_tune_adj(dev, port, REG_PORT_XMII_CTRL_4, val);
+}
+
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 			      struct phylink_config *config)
 {
@@ -327,6 +366,23 @@ void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 	}
 }
 
+void lan937x_setup_rgmii_delay(struct ksz_device *dev, int port)
+{
+	struct ksz_port *p = &dev->ports[port];
+
+	if (p->rgmii_tx_val) {
+		lan937x_set_rgmii_tx_delay(dev, port);
+		dev_info(dev->dev, "Applied rgmii tx delay for the port %d\n",
+			 port);
+	}
+
+	if (p->rgmii_rx_val) {
+		lan937x_set_rgmii_rx_delay(dev, port);
+		dev_info(dev->dev, "Applied rgmii rx delay for the port %d\n",
+			 port);
+	}
+}
+
 void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
 				unsigned int mode,
 				const struct phylink_link_state *state)
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
index a6cb3ca22dc3..ba4adaddb3ec 100644
--- a/drivers/net/dsa/microchip/lan937x_reg.h
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -136,6 +136,12 @@
 
 #define PORT_MII_SEL_EDGE		BIT(5)
 
+#define REG_PORT_XMII_CTRL_4		0x0304
+#define REG_PORT_XMII_CTRL_5		0x0306
+
+#define PORT_DLL_RESET			BIT(15)
+#define PORT_TUNE_ADJ			GENMASK(13, 7)
+
 /* 4 - MAC */
 #define REG_PORT_MAC_CTRL_0		0x0400
 #define PORT_CHECK_LENGTH		BIT(2)
@@ -161,6 +167,18 @@
 
 #define P_PRIO_CTRL			REG_PORT_MRI_PRIO_CTRL
 
+/* The port number as per the datasheet */
+#define RGMII_2_PORT_NUM		5
+#define RGMII_1_PORT_NUM		6
+
+#define LAN937X_RGMII_2_PORT		(RGMII_2_PORT_NUM - 1)
+#define LAN937X_RGMII_1_PORT		(RGMII_1_PORT_NUM - 1)
+
+#define RGMII_1_TX_DELAY_2NS		2
+#define RGMII_2_TX_DELAY_2NS		0
+#define RGMII_1_RX_DELAY_2NS		0x1B
+#define RGMII_2_RX_DELAY_2NS		0x14
+
 #define LAN937X_TAG_LEN			2
 
 #endif
-- 
2.36.1

[Patch net-next v1 7/9] net: dsa: microchip: ksz9477: use common xmii function

[Arun Ramadoss]

In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz9477.c     | 153 +-----------------------
 drivers/net/dsa/microchip/ksz9477_reg.h |  18 ---
 drivers/net/dsa/microchip/ksz_common.c  |  38 +++++-
 drivers/net/dsa/microchip/ksz_common.h  |   7 +-
 4 files changed, 49 insertions(+), 167 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index cfa7ddf60718..301283d1ba82 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -19,11 +19,6 @@
 #include "ksz_common.h"
 #include "ksz9477.h"
 
-/* Used with variable features to indicate capabilities. */
-#define GBIT_SUPPORT			BIT(0)
-#define NEW_XMII			BIT(1)
-#define IS_9893				BIT(2)
-
 static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
 {
 	regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
@@ -866,116 +861,18 @@ void ksz9477_port_mirror_del(struct ksz_device *dev, int port,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
-static int ksz9477_get_xmii(struct ksz_device *dev, u8 data)
-{
-	int mode;
-
-	if (dev->features & NEW_XMII) {
-		switch (data & PORT_MII_SEL_M) {
-		case PORT_MII_SEL:
-			mode = 0;
-			break;
-		case PORT_RMII_SEL:
-			mode = 1;
-			break;
-		case PORT_GMII_SEL:
-			mode = 2;
-			break;
-		default:
-			mode = 3;
-		}
-	} else {
-		switch (data & PORT_MII_SEL_M) {
-		case PORT_MII_SEL_S1:
-			mode = 0;
-			break;
-		case PORT_RMII_SEL_S1:
-			mode = 1;
-			break;
-		case PORT_GMII_SEL_S1:
-			mode = 2;
-			break;
-		default:
-			mode = 3;
-		}
-	}
-	return mode;
-}
-
-static void ksz9477_set_xmii(struct ksz_device *dev, int mode, u8 *data)
-{
-	u8 xmii;
-
-	if (dev->features & NEW_XMII) {
-		switch (mode) {
-		case 0:
-			xmii = PORT_MII_SEL;
-			break;
-		case 1:
-			xmii = PORT_RMII_SEL;
-			break;
-		case 2:
-			xmii = PORT_GMII_SEL;
-			break;
-		default:
-			xmii = PORT_RGMII_SEL;
-			break;
-		}
-	} else {
-		switch (mode) {
-		case 0:
-			xmii = PORT_MII_SEL_S1;
-			break;
-		case 1:
-			xmii = PORT_RMII_SEL_S1;
-			break;
-		case 2:
-			xmii = PORT_GMII_SEL_S1;
-			break;
-		default:
-			xmii = PORT_RGMII_SEL_S1;
-			break;
-		}
-	}
-	*data &= ~PORT_MII_SEL_M;
-	*data |= xmii;
-}
-
 static phy_interface_t ksz9477_get_interface(struct ksz_device *dev, int port)
 {
 	phy_interface_t interface;
 	bool gbit;
-	int mode;
-	u8 data8;
 
 	if (port < dev->phy_port_cnt)
 		return PHY_INTERFACE_MODE_NA;
-	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
+
 	gbit = ksz_get_gbit(dev, port);
-	mode = ksz9477_get_xmii(dev, data8);
-	switch (mode) {
-	case 2:
-		interface = PHY_INTERFACE_MODE_GMII;
-		if (gbit)
-			break;
-		fallthrough;
-	case 0:
-		interface = PHY_INTERFACE_MODE_MII;
-		break;
-	case 1:
-		interface = PHY_INTERFACE_MODE_RMII;
-		break;
-	default:
-		interface = PHY_INTERFACE_MODE_RGMII;
-		if (data8 & PORT_RGMII_ID_EG_ENABLE)
-			interface = PHY_INTERFACE_MODE_RGMII_TXID;
-		if (data8 & PORT_RGMII_ID_IG_ENABLE) {
-			interface = PHY_INTERFACE_MODE_RGMII_RXID;
-			if (data8 & PORT_RGMII_ID_EG_ENABLE)
-				interface = PHY_INTERFACE_MODE_RGMII_ID;
-		}
-		break;
-	}
+
+	interface = ksz_get_xmii(dev, port, gbit);
+
 	return interface;
 }
 
@@ -1049,8 +946,8 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 {
 	struct ksz_port *p = &dev->ports[port];
 	struct dsa_switch *ds = dev->ds;
-	u8 data8, member;
 	u16 data16;
+	u8 member;
 
 	/* enable tag tail for host port */
 	if (cpu_port)
@@ -1092,42 +989,7 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 			     true);
 
 		/* configure MAC to 1G & RGMII mode */
-		ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
-		switch (p->interface) {
-		case PHY_INTERFACE_MODE_MII:
-			ksz9477_set_xmii(dev, 0, &data8);
-			ksz_set_gbit(dev, port, false);
-			p->phydev.speed = SPEED_100;
-			break;
-		case PHY_INTERFACE_MODE_RMII:
-			ksz9477_set_xmii(dev, 1, &data8);
-			ksz_set_gbit(dev, port, false);
-			p->phydev.speed = SPEED_100;
-			break;
-		case PHY_INTERFACE_MODE_GMII:
-			ksz9477_set_xmii(dev, 2, &data8);
-			ksz_set_gbit(dev, port, true);
-			p->phydev.speed = SPEED_1000;
-			break;
-		default:
-			ksz9477_set_xmii(dev, 3, &data8);
-			ksz_set_gbit(dev, port, true);
-			data8 &= ~PORT_RGMII_ID_IG_ENABLE;
-			data8 &= ~PORT_RGMII_ID_EG_ENABLE;
-			if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			    p->interface == PHY_INTERFACE_MODE_RGMII_RXID)
-				data8 |= PORT_RGMII_ID_IG_ENABLE;
-			if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			    p->interface == PHY_INTERFACE_MODE_RGMII_TXID)
-				data8 |= PORT_RGMII_ID_EG_ENABLE;
-			/* On KSZ9893, disable RGMII in-band status support */
-			if (dev->features & IS_9893)
-				data8 &= ~PORT_MII_MAC_MODE;
-			p->phydev.speed = SPEED_1000;
-			break;
-		}
-		ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
-		p->phydev.duplex = 1;
+		ksz_set_xmii(dev, port, p->interface);
 	}
 
 	if (cpu_port)
@@ -1315,9 +1177,6 @@ int ksz9477_switch_init(struct ksz_device *dev)
 			dev->features &= ~GBIT_SUPPORT;
 		dev->phy_port_cnt = 2;
 	} else {
-		/* Chip uses new XMII register definitions. */
-		dev->features |= NEW_XMII;
-
 		/* Chip does not support gigabit. */
 		if (!(data8 & SW_GIGABIT_ABLE))
 			dev->features &= ~GBIT_SUPPORT;
diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index 6ca859345932..ddf99d1e4bbd 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -1175,29 +1175,11 @@
 #define PORT_LINK_STATUS_FAIL		BIT(0)
 
 /* 3 - xMII */
-#define REG_PORT_XMII_CTRL_0		0x0300
-
 #define PORT_SGMII_SEL			BIT(7)
 #define PORT_GRXC_ENABLE		BIT(0)
 
-#define REG_PORT_XMII_CTRL_1		0x0301
-
 #define PORT_RMII_CLK_SEL		BIT(7)
 #define PORT_MII_SEL_EDGE		BIT(5)
-#define PORT_RGMII_ID_IG_ENABLE		BIT(4)
-#define PORT_RGMII_ID_EG_ENABLE		BIT(3)
-#define PORT_MII_MAC_MODE		BIT(2)
-#define PORT_MII_SEL_M			0x3
-/* S1 */
-#define PORT_MII_SEL_S1			0x0
-#define PORT_RMII_SEL_S1		0x1
-#define PORT_GMII_SEL_S1		0x2
-#define PORT_RGMII_SEL_S1		0x3
-/* S2 */
-#define PORT_RGMII_SEL			0x0
-#define PORT_RMII_SEL			0x1
-#define PORT_GMII_SEL			0x2
-#define PORT_MII_SEL			0x3
 
 /* 4 - MAC */
 #define REG_PORT_MAC_CTRL_0		0x0400
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 65a4ed77f3cc..35723ca227b7 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -1436,6 +1436,9 @@ void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 		data8 |= bitval[P_RGMII_SEL];
+		/* On KSZ9893, disable RGMII in-band status support */
+		if (dev->features & IS_9893)
+			data8 &= ~P_MII_MAC_MODE;
 		break;
 	default:
 		dev_err(dev->dev, "Unsupported interface '%s' for port %d\n",
@@ -1453,6 +1456,39 @@ void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
 	ksz_pwrite8(dev, port, regs[P_XMII_CTRL_1], data8);
 }
 
+phy_interface_t ksz_get_xmii(struct ksz_device *dev, int port, bool gbit)
+{
+	const u8 *bitval = dev->info->xmii_ctrl1;
+	const u16 *regs = dev->info->regs;
+	phy_interface_t interface;
+	u8 data8;
+	u8 val;
+
+	ksz_pread8(dev, port, regs[P_XMII_CTRL_1], &data8);
+
+	val = FIELD_GET(P_MII_SEL_M, data8);
+
+	if (val == bitval[P_MII_SEL]) {
+		if (gbit)
+			interface = PHY_INTERFACE_MODE_GMII;
+		else
+			interface = PHY_INTERFACE_MODE_MII;
+	} else if (val == bitval[P_RMII_SEL]) {
+		interface = PHY_INTERFACE_MODE_RGMII;
+	} else {
+		interface = PHY_INTERFACE_MODE_RGMII;
+		if (data8 & P_RGMII_ID_EG_ENABLE)
+			interface = PHY_INTERFACE_MODE_RGMII_TXID;
+		if (data8 & P_RGMII_ID_IG_ENABLE) {
+			interface = PHY_INTERFACE_MODE_RGMII_RXID;
+			if (data8 & P_RGMII_ID_EG_ENABLE)
+				interface = PHY_INTERFACE_MODE_RGMII_ID;
+		}
+	}
+
+	return interface;
+}
+
 static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 				   unsigned int mode,
 				   const struct phylink_link_state *state)
@@ -1484,7 +1520,7 @@ bool ksz_get_gbit(struct ksz_device *dev, int port)
 	return gbit;
 }
 
-void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit)
+static void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit)
 {
 	const u8 *bitval = dev->info->xmii_ctrl1;
 	const u16 *regs = dev->info->regs;
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 61942e0636d6..9fd52bf99d94 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -319,8 +319,8 @@ void ksz_init_mib_timer(struct ksz_device *dev);
 void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
-void ksz_set_gbit(struct ksz_device *dev, int port, bool gbit);
 void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface);
+phy_interface_t ksz_get_xmii(struct ksz_device *dev, int port, bool gbit);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
 /* Common register access functions */
@@ -484,6 +484,10 @@ static inline int is_lan937x(struct ksz_device *dev)
 
 #define SW_START			0x01
 
+/* Used with variable features to indicate capabilities. */
+#define GBIT_SUPPORT			BIT(0)
+#define IS_9893				BIT(2)
+
 /* xMII configuration */
 #define P_MII_DUPLEX_M			BIT(6)
 #define P_MII_100MBIT_M			BIT(4)
@@ -491,6 +495,7 @@ static inline int is_lan937x(struct ksz_device *dev)
 #define P_GMII_1GBIT_M			BIT(6)
 #define P_RGMII_ID_IG_ENABLE		BIT(4)
 #define P_RGMII_ID_EG_ENABLE		BIT(3)
+#define P_MII_MAC_MODE			BIT(2)
 #define P_MII_SEL_M			0x3
 
 /* Regmap tables generation */
-- 
2.36.1

[Patch net-next v1 8/9] net: dsa: microchip: ksz8795: use common xmii function

[Arun Ramadoss]

This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz8795.c     | 35 +------------------------
 drivers/net/dsa/microchip/ksz8795_reg.h |  8 ------
 2 files changed, 1 insertion(+), 42 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 911aace42284..8f807d8eace5 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -1116,7 +1116,6 @@ void ksz8_port_mirror_del(struct ksz_device *dev, int port,
 static void ksz8795_cpu_interface_select(struct ksz_device *dev, int port)
 {
 	struct ksz_port *p = &dev->ports[port];
-	u8 data8;
 
 	if (!p->interface && dev->compat_interface) {
 		dev_warn(dev->dev,
@@ -1126,39 +1125,7 @@ static void ksz8795_cpu_interface_select(struct ksz_device *dev, int port)
 		p->interface = dev->compat_interface;
 	}
 
-	/* Configure MII interface for proper network communication. */
-	ksz_read8(dev, REG_PORT_5_CTRL_6, &data8);
-	data8 &= ~PORT_INTERFACE_TYPE;
-	data8 &= ~PORT_GMII_1GPS_MODE;
-	switch (p->interface) {
-	case PHY_INTERFACE_MODE_MII:
-		p->phydev.speed = SPEED_100;
-		break;
-	case PHY_INTERFACE_MODE_RMII:
-		data8 |= PORT_INTERFACE_RMII;
-		p->phydev.speed = SPEED_100;
-		break;
-	case PHY_INTERFACE_MODE_GMII:
-		data8 |= PORT_GMII_1GPS_MODE;
-		data8 |= PORT_INTERFACE_GMII;
-		p->phydev.speed = SPEED_1000;
-		break;
-	default:
-		data8 &= ~PORT_RGMII_ID_IN_ENABLE;
-		data8 &= ~PORT_RGMII_ID_OUT_ENABLE;
-		if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-		    p->interface == PHY_INTERFACE_MODE_RGMII_RXID)
-			data8 |= PORT_RGMII_ID_IN_ENABLE;
-		if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-		    p->interface == PHY_INTERFACE_MODE_RGMII_TXID)
-			data8 |= PORT_RGMII_ID_OUT_ENABLE;
-		data8 |= PORT_GMII_1GPS_MODE;
-		data8 |= PORT_INTERFACE_RGMII;
-		p->phydev.speed = SPEED_1000;
-		break;
-	}
-	ksz_write8(dev, REG_PORT_5_CTRL_6, data8);
-	p->phydev.duplex = 1;
+	ksz_set_xmii(dev, port, p->interface);
 }
 
 void ksz8_port_setup(struct ksz_device *dev, int port, bool cpu_port)
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index a848eb4c54cb..77487d611824 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -170,15 +170,7 @@
 #define REG_PORT_5_CTRL_6		0x56
 
 #define PORT_MII_INTERNAL_CLOCK		BIT(7)
-#define PORT_GMII_1GPS_MODE		BIT(6)
-#define PORT_RGMII_ID_IN_ENABLE		BIT(4)
-#define PORT_RGMII_ID_OUT_ENABLE	BIT(3)
 #define PORT_GMII_MAC_MODE		BIT(2)
-#define PORT_INTERFACE_TYPE		0x3
-#define PORT_INTERFACE_MII		0
-#define PORT_INTERFACE_RMII		1
-#define PORT_INTERFACE_GMII		2
-#define PORT_INTERFACE_RGMII		3
 
 #define REG_PORT_1_CTRL_7		0x17
 #define REG_PORT_2_CTRL_7		0x27
-- 
2.36.1

[Patch net-next v1 9/9] net: dsa: microchip: add support for phylink mac config

[Arun Ramadoss]

This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
 drivers/net/dsa/microchip/ksz8795.c      |  7 -------
 drivers/net/dsa/microchip/ksz9477.c      |  4 ----
 drivers/net/dsa/microchip/ksz_common.c   | 18 ++++++++++++++++--
 drivers/net/dsa/microchip/ksz_common.h   |  6 +++++-
 drivers/net/dsa/microchip/lan937x.h      |  3 ---
 drivers/net/dsa/microchip/lan937x_main.c | 16 ----------------
 6 files changed, 21 insertions(+), 33 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 8f807d8eace5..c79a5128235f 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -26,11 +26,6 @@
 #include "ksz8795_reg.h"
 #include "ksz8.h"
 
-static bool ksz_is_ksz88x3(struct ksz_device *dev)
-{
-	return dev->chip_id == 0x8830;
-}
-
 static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
 {
 	regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
@@ -1124,8 +1119,6 @@ static void ksz8795_cpu_interface_select(struct ksz_device *dev, int port)
 			 port);
 		p->interface = dev->compat_interface;
 	}
-
-	ksz_set_xmii(dev, port, p->interface);
 }
 
 void ksz8_port_setup(struct ksz_device *dev, int port, bool cpu_port)
diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index 301283d1ba82..4b14d80d27ed 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -944,7 +944,6 @@ void ksz9477_get_caps(struct ksz_device *dev, int port,
 
 void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 {
-	struct ksz_port *p = &dev->ports[port];
 	struct dsa_switch *ds = dev->ds;
 	u16 data16;
 	u8 member;
@@ -987,9 +986,6 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 		ksz_port_cfg(dev, port, REG_PORT_CTRL_0,
 			     PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL,
 			     true);
-
-		/* configure MAC to 1G & RGMII mode */
-		ksz_set_xmii(dev, port, p->interface);
 	}
 
 	if (cpu_port)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 35723ca227b7..407bcd58cfa7 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -222,7 +222,6 @@ static const struct ksz_dev_ops lan937x_dev_ops = {
 	.mirror_add = ksz9477_port_mirror_add,
 	.mirror_del = ksz9477_port_mirror_del,
 	.get_caps = lan937x_phylink_get_caps,
-	.phylink_mac_config = lan937x_phylink_mac_config,
 	.setup_rgmii_delay = lan937x_setup_rgmii_delay,
 	.fdb_dump = ksz9477_fdb_dump,
 	.fdb_add = ksz9477_fdb_add,
@@ -1409,7 +1408,8 @@ static int ksz_max_mtu(struct dsa_switch *ds, int port)
 	return dev->dev_ops->max_mtu(dev, port);
 }
 
-void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface)
+static void ksz_set_xmii(struct ksz_device *dev, int port,
+			 phy_interface_t interface)
 {
 	const u8 *bitval = dev->info->xmii_ctrl1;
 	struct ksz_port *p = &dev->ports[port];
@@ -1495,6 +1495,20 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 {
 	struct ksz_device *dev = ds->priv;
 
+	if (ksz_is_ksz88x3(dev))
+		return;
+
+	/* Internal PHYs */
+	if (dev->info->internal_phy[port])
+		return;
+
+	if (phylink_autoneg_inband(mode)) {
+		dev_err(dev->dev, "In-band AN not supported!\n");
+		return;
+	}
+
+	ksz_set_xmii(dev, port, state->interface);
+
 	if (dev->dev_ops->phylink_mac_config)
 		dev->dev_ops->phylink_mac_config(dev, port, mode, state);
 
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 9fd52bf99d94..0412c2bc5f55 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -319,7 +319,6 @@ void ksz_init_mib_timer(struct ksz_device *dev);
 void ksz_r_mib_stats64(struct ksz_device *dev, int port);
 void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
 bool ksz_get_gbit(struct ksz_device *dev, int port);
-void ksz_set_xmii(struct ksz_device *dev, int port, phy_interface_t interface);
 phy_interface_t ksz_get_xmii(struct ksz_device *dev, int port, bool gbit);
 extern const struct ksz_chip_data ksz_switch_chips[];
 
@@ -439,6 +438,11 @@ static inline void ksz_regmap_unlock(void *__mtx)
 	mutex_unlock(mtx);
 }
 
+static inline bool ksz_is_ksz88x3(struct ksz_device *dev)
+{
+	return dev->chip_id == KSZ8830_CHIP_ID;
+}
+
 static inline int is_lan937x(struct ksz_device *dev)
 {
 	return dev->chip_id == LAN9370_CHIP_ID ||
diff --git a/drivers/net/dsa/microchip/lan937x.h b/drivers/net/dsa/microchip/lan937x.h
index 423521a13c9e..4e0b1dccec27 100644
--- a/drivers/net/dsa/microchip/lan937x.h
+++ b/drivers/net/dsa/microchip/lan937x.h
@@ -17,8 +17,5 @@ void lan937x_w_phy(struct ksz_device *dev, u16 addr, u16 reg, u16 val);
 int lan937x_change_mtu(struct ksz_device *dev, int port, int new_mtu);
 void lan937x_phylink_get_caps(struct ksz_device *dev, int port,
 			      struct phylink_config *config);
-void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
-				unsigned int mode,
-				const struct phylink_link_state *state);
 void lan937x_setup_rgmii_delay(struct ksz_device *dev, int port);
 #endif
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index 797fe7f62394..daedd2bf20c1 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -383,22 +383,6 @@ void lan937x_setup_rgmii_delay(struct ksz_device *dev, int port)
 	}
 }
 
-void lan937x_phylink_mac_config(struct ksz_device *dev, int port,
-				unsigned int mode,
-				const struct phylink_link_state *state)
-{
-	/* Internal PHYs */
-	if (dev->info->internal_phy[port])
-		return;
-
-	if (phylink_autoneg_inband(mode)) {
-		dev_err(dev->dev, "In-band AN not supported!\n");
-		return;
-	}
-
-	ksz_set_xmii(dev, port, state->interface);
-}
-
 int lan937x_setup(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
-- 
2.36.1