[PATCH RFC net-next 00/16] net: add negotiation of in-band capabilities

[PATCH RFC net-next 00/16] net: add negotiation of in-band capabilities

[Russell King (Oracle)]

Hi,

Yes, this is one patch over the limit of 15 for netdev - but I think it's
important to include the last patch to head off review comments like "why
don't you remove phylink_phy_no_inband() in this series?"

Phylink's handling of in-band has been deficient for a long time, and
people keep hitting problems with it. Notably, situations with the way-
to-late standardized 2500Base-X and whether that should or should not
have in-band enabled. We have also been carrying a hack in the form of
phylink_phy_no_inband() for a PHY that has been used on a SFP module,
but has no in-band capabilities, not even for SGMII.

When phylink is trying to operate in in-band mode, this series will look
at the capabilities of the MAC-side PCS and PHY, and work out whether
in-band can or should be used, programming the PHY as appropriate. This
includes in-band bypass mode at the PHY.

We don't... yet... support that on the MAC side PCS, because that
requires yet more complexity.

Patch 1 passes struct phylink and struct phylink_pcs into
phylink_pcs_neg_mode() so we can look at more state in this function in
a future patch.

Patch 2 splits "cur_link_an_mode" (the MLO_AN_* mode) into two separate
purposes - a requested and an active mode. The active mode is the one
we will be using for the MAC, which becomes dependent on the result of
in-band negotiation.

Patch 3 adds debug to phylink_major_config() so we can see what is going
on with the requested and active AN modes.

Patch 4 adds to phylib a method to get the in-band capabilities of the
PHY from phylib. Patches 5 and 6 add implementations for BCM84881 and
some Marvell PHYs found on SFPs.

Patch 7 adds to phylib a method to configure the PHY in-band signalling,
and patch 8 implements it for those Marvell PHYs that support the method
in patch 4.

Patch 9 does the same as patch 4 but for the MAC-side PCS, with patches
10 through 14 adding support to several PCS.

Patch 15 adds the code to phylink_pcs_neg_mode() which looks at the
capabilities, and works out whether to use in-band or out-band mode for
driving the link between the MAC PCS and PHY.

Patch 16 removes the phylink_phy_no_inband() hack now that we are
publishing the in-band capabilities from the BCM84881 PHY driver.

 drivers/net/ethernet/marvell/mvneta.c           |  27 +-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c |  25 +-
 drivers/net/pcs/pcs-lynx.c                      |  22 ++
 drivers/net/pcs/pcs-mtk-lynxi.c                 |  16 ++
 drivers/net/pcs/pcs-xpcs.c                      |  28 ++
 drivers/net/phy/bcm84881.c                      |  10 +
 drivers/net/phy/marvell.c                       |  48 ++++
 drivers/net/phy/phy.c                           |  52 ++++
 drivers/net/phy/phylink.c                       | 352 +++++++++++++++++++-----
 include/linux/phy.h                             |  34 +++
 include/linux/phylink.h                         |  17 ++
 11 files changed, 539 insertions(+), 92 deletions(-)

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

[PATCH RFC net-next 01/16] net: phylink: pass phylink and pcs into phylink_pcs_neg_mode()

[Russell King (Oracle)]

Move the call to phylink_pcs_neg_mode() in phylink_major_config() after
we have selected the appropriate PCS to allow the PCS to be passed in.

Add struct phylink and struct phylink_pcs pointers to
phylink_pcs_neg_mode() and pass in the appropriate structures. Set
pl->pcs_neg_mode before returning, and remove the return value.

This will allow the capabilities of the PCS and any PHY to be used when
deciding which pcs_neg_mode should be used.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 3b5ceca2637c..8a43b81d5846 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1085,7 +1085,8 @@ static void phylink_pcs_an_restart(struct phylink *pl)
 
 /**
  * phylink_pcs_neg_mode() - helper to determine PCS inband mode
- * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
+ * @pl: a pointer to a &struct phylink returned from phylink_create()
+ * @pcs: a pointer to &struct phylink_pcs
  * @interface: interface mode to be used
  * @advertising: adertisement ethtool link mode mask
  *
@@ -1102,11 +1103,13 @@ static void phylink_pcs_an_restart(struct phylink *pl)
  * Note: this is for cases where the PCS itself is involved in negotiation
  * (e.g. Clause 37, SGMII and similar) not Clause 73.
  */
-static unsigned int phylink_pcs_neg_mode(unsigned int mode,
-					 phy_interface_t interface,
-					 const unsigned long *advertising)
+static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
+				 phy_interface_t interface,
+				 const unsigned long *advertising)
 {
-	unsigned int neg_mode;
+	unsigned int neg_mode, mode;
+
+	mode = pl->cur_link_an_mode;
 
 	switch (interface) {
 	case PHY_INTERFACE_MODE_SGMII:
@@ -1147,7 +1150,7 @@ static unsigned int phylink_pcs_neg_mode(unsigned int mode,
 		break;
 	}
 
-	return neg_mode;
+	pl->pcs_neg_mode = neg_mode;
 }
 
 static void phylink_major_config(struct phylink *pl, bool restart,
@@ -1161,10 +1164,6 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 
 	phylink_dbg(pl, "major config %s\n", phy_modes(state->interface));
 
-	pl->pcs_neg_mode = phylink_pcs_neg_mode(pl->cur_link_an_mode,
-						state->interface,
-						state->advertising);
-
 	if (pl->mac_ops->mac_select_pcs) {
 		pcs = pl->mac_ops->mac_select_pcs(pl->config, state->interface);
 		if (IS_ERR(pcs)) {
@@ -1177,6 +1176,8 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 		pcs_changed = pl->pcs != pcs;
 	}
 
+	phylink_pcs_neg_mode(pl, pcs, state->interface, state->advertising);
+
 	phylink_pcs_poll_stop(pl);
 
 	if (pl->mac_ops->mac_prepare) {
@@ -1267,9 +1268,8 @@ static int phylink_change_inband_advert(struct phylink *pl)
 		    pl->link_config.pause);
 
 	/* Recompute the PCS neg mode */
-	pl->pcs_neg_mode = phylink_pcs_neg_mode(pl->cur_link_an_mode,
-					pl->link_config.interface,
-					pl->link_config.advertising);
+	phylink_pcs_neg_mode(pl, pl->pcs, pl->link_config.interface,
+			     pl->link_config.advertising);
 
 	neg_mode = pl->cur_link_an_mode;
 	if (pl->pcs->neg_mode)
-- 
2.30.2

[PATCH RFC net-next 02/16] net: phylink: split cur_link_an_mode into requested and active

[Russell King (Oracle)]

There is an interdependence between the current link_an_mode and
pcs_neg_mode that some drivers rely upon to know whether inband or PHY
mode will be used.

In order to support detection of PCS and PHY inband capabilities
resulting in automatic selection of inband or PHY mode, we need to
cater for this, and support changing the MAC link_an_mode. However, we
end up with an inter-dependency between the current link_an_mode and
pcs_neg_mode.

To solve this, split the current link_an_mode into the requested
link_an_mode and active link_an_mode. The requested link_an_mode will
always be passed to phylink_pcs_neg_mode(), and the active link_an_mode
will be used for everything else, and only updated during
phylink_major_config(). This will ensure that phylink_pcs_neg_mode()'s
link_an_mode will not depend on the active link_an_mode that will,
in a future patch, depend on pcs_neg_mode.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 60 ++++++++++++++++++++-------------------
 1 file changed, 31 insertions(+), 29 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 8a43b81d5846..43a817de4bc8 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -56,7 +56,8 @@ struct phylink {
 	struct phy_device *phydev;
 	phy_interface_t link_interface;	/* PHY_INTERFACE_xxx */
 	u8 cfg_link_an_mode;		/* MLO_AN_xxx */
-	u8 cur_link_an_mode;
+	u8 req_link_an_mode;		/* Requested MLO_AN_xxx mode */
+	u8 act_link_an_mode;		/* Active MLO_AN_xxx mode */
 	u8 link_port;			/* The current non-phy ethtool port */
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported);
 
@@ -1065,13 +1066,13 @@ static void phylink_mac_config(struct phylink *pl,
 
 	phylink_dbg(pl,
 		    "%s: mode=%s/%s/%s adv=%*pb pause=%02x\n",
-		    __func__, phylink_an_mode_str(pl->cur_link_an_mode),
+		    __func__, phylink_an_mode_str(pl->act_link_an_mode),
 		    phy_modes(st.interface),
 		    phy_rate_matching_to_str(st.rate_matching),
 		    __ETHTOOL_LINK_MODE_MASK_NBITS, st.advertising,
 		    st.pause);
 
-	pl->mac_ops->mac_config(pl->config, pl->cur_link_an_mode, &st);
+	pl->mac_ops->mac_config(pl->config, pl->act_link_an_mode, &st);
 }
 
 static void phylink_pcs_an_restart(struct phylink *pl)
@@ -1079,7 +1080,7 @@ static void phylink_pcs_an_restart(struct phylink *pl)
 	if (pl->pcs && linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 					 pl->link_config.advertising) &&
 	    phy_interface_mode_is_8023z(pl->link_config.interface) &&
-	    phylink_autoneg_inband(pl->cur_link_an_mode))
+	    phylink_autoneg_inband(pl->act_link_an_mode))
 		pl->pcs->ops->pcs_an_restart(pl->pcs);
 }
 
@@ -1109,7 +1110,7 @@ static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
 {
 	unsigned int neg_mode, mode;
 
-	mode = pl->cur_link_an_mode;
+	mode = pl->req_link_an_mode;
 
 	switch (interface) {
 	case PHY_INTERFACE_MODE_SGMII:
@@ -1151,6 +1152,7 @@ static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
 	}
 
 	pl->pcs_neg_mode = neg_mode;
+	pl->act_link_an_mode = mode;
 }
 
 static void phylink_major_config(struct phylink *pl, bool restart,
@@ -1181,7 +1183,7 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 	phylink_pcs_poll_stop(pl);
 
 	if (pl->mac_ops->mac_prepare) {
-		err = pl->mac_ops->mac_prepare(pl->config, pl->cur_link_an_mode,
+		err = pl->mac_ops->mac_prepare(pl->config, pl->act_link_an_mode,
 					       state->interface);
 		if (err < 0) {
 			phylink_err(pl, "mac_prepare failed: %pe\n",
@@ -1215,7 +1217,7 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 	if (pl->pcs_state == PCS_STATE_STARTING || pcs_changed)
 		phylink_pcs_enable(pl->pcs);
 
-	neg_mode = pl->cur_link_an_mode;
+	neg_mode = pl->act_link_an_mode;
 	if (pl->pcs && pl->pcs->neg_mode)
 		neg_mode = pl->pcs_neg_mode;
 
@@ -1231,7 +1233,7 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 		phylink_pcs_an_restart(pl);
 
 	if (pl->mac_ops->mac_finish) {
-		err = pl->mac_ops->mac_finish(pl->config, pl->cur_link_an_mode,
+		err = pl->mac_ops->mac_finish(pl->config, pl->act_link_an_mode,
 					      state->interface);
 		if (err < 0)
 			phylink_err(pl, "mac_finish failed: %pe\n",
@@ -1262,7 +1264,7 @@ static int phylink_change_inband_advert(struct phylink *pl)
 		return 0;
 
 	phylink_dbg(pl, "%s: mode=%s/%s adv=%*pb pause=%02x\n", __func__,
-		    phylink_an_mode_str(pl->cur_link_an_mode),
+		    phylink_an_mode_str(pl->req_link_an_mode),
 		    phy_modes(pl->link_config.interface),
 		    __ETHTOOL_LINK_MODE_MASK_NBITS, pl->link_config.advertising,
 		    pl->link_config.pause);
@@ -1271,7 +1273,7 @@ static int phylink_change_inband_advert(struct phylink *pl)
 	phylink_pcs_neg_mode(pl, pl->pcs, pl->link_config.interface,
 			     pl->link_config.advertising);
 
-	neg_mode = pl->cur_link_an_mode;
+	neg_mode = pl->act_link_an_mode;
 	if (pl->pcs->neg_mode)
 		neg_mode = pl->pcs_neg_mode;
 
@@ -1336,7 +1338,7 @@ static void phylink_mac_initial_config(struct phylink *pl, bool force_restart)
 {
 	struct phylink_link_state link_state;
 
-	switch (pl->cur_link_an_mode) {
+	switch (pl->req_link_an_mode) {
 	case MLO_AN_PHY:
 		link_state = pl->phy_state;
 		break;
@@ -1410,14 +1412,14 @@ static void phylink_link_up(struct phylink *pl,
 
 	pl->cur_interface = link_state.interface;
 
-	neg_mode = pl->cur_link_an_mode;
+	neg_mode = pl->act_link_an_mode;
 	if (pl->pcs && pl->pcs->neg_mode)
 		neg_mode = pl->pcs_neg_mode;
 
 	phylink_pcs_link_up(pl->pcs, neg_mode, pl->cur_interface, speed,
 			    duplex);
 
-	pl->mac_ops->mac_link_up(pl->config, pl->phydev, pl->cur_link_an_mode,
+	pl->mac_ops->mac_link_up(pl->config, pl->phydev, pl->act_link_an_mode,
 				 pl->cur_interface, speed, duplex,
 				 !!(link_state.pause & MLO_PAUSE_TX), rx_pause);
 
@@ -1437,7 +1439,7 @@ static void phylink_link_down(struct phylink *pl)
 
 	if (ndev)
 		netif_carrier_off(ndev);
-	pl->mac_ops->mac_link_down(pl->config, pl->cur_link_an_mode,
+	pl->mac_ops->mac_link_down(pl->config, pl->act_link_an_mode,
 				   pl->cur_interface);
 	phylink_info(pl, "Link is Down\n");
 }
@@ -1463,10 +1465,10 @@ static void phylink_resolve(struct work_struct *w)
 	} else if (pl->link_failed) {
 		link_state.link = false;
 		retrigger = true;
-	} else if (pl->cur_link_an_mode == MLO_AN_FIXED) {
+	} else if (pl->act_link_an_mode == MLO_AN_FIXED) {
 		phylink_get_fixed_state(pl, &link_state);
 		mac_config = link_state.link;
-	} else if (pl->cur_link_an_mode == MLO_AN_PHY) {
+	} else if (pl->act_link_an_mode == MLO_AN_PHY) {
 		link_state = pl->phy_state;
 		mac_config = link_state.link;
 	} else {
@@ -1520,7 +1522,7 @@ static void phylink_resolve(struct work_struct *w)
 		}
 	}
 
-	if (pl->cur_link_an_mode != MLO_AN_FIXED)
+	if (pl->act_link_an_mode != MLO_AN_FIXED)
 		phylink_apply_manual_flow(pl, &link_state);
 
 	if (mac_config) {
@@ -1644,7 +1646,7 @@ int phylink_set_fixed_link(struct phylink *pl,
 	pl->link_config.an_complete = 1;
 
 	pl->cfg_link_an_mode = MLO_AN_FIXED;
-	pl->cur_link_an_mode = pl->cfg_link_an_mode;
+	pl->req_link_an_mode = pl->cfg_link_an_mode;
 
 	return 0;
 }
@@ -1732,7 +1734,7 @@ struct phylink *phylink_create(struct phylink_config *config,
 		}
 	}
 
-	pl->cur_link_an_mode = pl->cfg_link_an_mode;
+	pl->req_link_an_mode = pl->cfg_link_an_mode;
 
 	ret = phylink_register_sfp(pl, fwnode);
 	if (ret < 0) {
@@ -2198,7 +2200,7 @@ void phylink_start(struct phylink *pl)
 	ASSERT_RTNL();
 
 	phylink_info(pl, "configuring for %s/%s link mode\n",
-		     phylink_an_mode_str(pl->cur_link_an_mode),
+		     phylink_an_mode_str(pl->req_link_an_mode),
 		     phy_modes(pl->link_config.interface));
 
 	/* Always set the carrier off */
@@ -2483,7 +2485,7 @@ int phylink_ethtool_ksettings_get(struct phylink *pl,
 
 	linkmode_copy(kset->link_modes.supported, pl->supported);
 
-	switch (pl->cur_link_an_mode) {
+	switch (pl->act_link_an_mode) {
 	case MLO_AN_FIXED:
 		/* We are using fixed settings. Report these as the
 		 * current link settings - and note that these also
@@ -2575,7 +2577,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 		/* If we have a fixed link, refuse to change link parameters.
 		 * If the link parameters match, accept them but do nothing.
 		 */
-		if (pl->cur_link_an_mode == MLO_AN_FIXED) {
+		if (pl->req_link_an_mode == MLO_AN_FIXED) {
 			if (s->speed != pl->link_config.speed ||
 			    s->duplex != pl->link_config.duplex)
 				return -EINVAL;
@@ -2591,7 +2593,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 		 * is our default case) but do not allow the advertisement to
 		 * be changed. If the advertisement matches, simply return.
 		 */
-		if (pl->cur_link_an_mode == MLO_AN_FIXED) {
+		if (pl->req_link_an_mode == MLO_AN_FIXED) {
 			if (!linkmode_equal(config.advertising,
 					    pl->link_config.advertising))
 				return -EINVAL;
@@ -2626,7 +2628,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 		linkmode_copy(support, pl->supported);
 		if (phylink_validate(pl, support, &config)) {
 			phylink_err(pl, "validation of %s/%s with support %*pb failed\n",
-				    phylink_an_mode_str(pl->cur_link_an_mode),
+				    phylink_an_mode_str(pl->req_link_an_mode),
 				    phy_modes(config.interface),
 				    __ETHTOOL_LINK_MODE_MASK_NBITS, support);
 			return -EINVAL;
@@ -2726,7 +2728,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 
 	ASSERT_RTNL();
 
-	if (pl->cur_link_an_mode == MLO_AN_FIXED)
+	if (pl->req_link_an_mode == MLO_AN_FIXED)
 		return -EOPNOTSUPP;
 
 	if (!phylink_test(pl->supported, Pause) &&
@@ -2990,7 +2992,7 @@ static int phylink_mii_read(struct phylink *pl, unsigned int phy_id,
 	struct phylink_link_state state;
 	int val = 0xffff;
 
-	switch (pl->cur_link_an_mode) {
+	switch (pl->act_link_an_mode) {
 	case MLO_AN_FIXED:
 		if (phy_id == 0) {
 			phylink_get_fixed_state(pl, &state);
@@ -3015,7 +3017,7 @@ static int phylink_mii_read(struct phylink *pl, unsigned int phy_id,
 static int phylink_mii_write(struct phylink *pl, unsigned int phy_id,
 			     unsigned int reg, unsigned int val)
 {
-	switch (pl->cur_link_an_mode) {
+	switch (pl->act_link_an_mode) {
 	case MLO_AN_FIXED:
 		break;
 
@@ -3205,9 +3207,9 @@ static void phylink_sfp_set_config(struct phylink *pl, u8 mode,
 		changed = true;
 	}
 
-	if (pl->cur_link_an_mode != mode ||
+	if (pl->req_link_an_mode != mode ||
 	    pl->link_config.interface != state->interface) {
-		pl->cur_link_an_mode = mode;
+		pl->req_link_an_mode = mode;
 		pl->link_config.interface = state->interface;
 
 		changed = true;
-- 
2.30.2

[PATCH RFC net-next 03/16] net: phylink: add debug for phylink_major_config()

[Russell King (Oracle)]

Now that we have a more complexity in phylink_major_config(), augment
the debugging so we can see what's going on there.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 27 ++++++++++++++++++++++++++-
 1 file changed, 26 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 43a817de4bc8..e43a083cec57 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -175,6 +175,24 @@ static const char *phylink_an_mode_str(unsigned int mode)
 	return mode < ARRAY_SIZE(modestr) ? modestr[mode] : "unknown";
 }
 
+static const char *phylink_pcs_mode_str(unsigned int mode)
+{
+	if (!mode)
+		return "none";
+
+	if (mode & PHYLINK_PCS_NEG_OUTBAND)
+		return "outband";
+
+	if (mode & PHYLINK_PCS_NEG_INBAND) {
+		if (mode & PHYLINK_PCS_NEG_ENABLED)
+			return "inband,an-enabled";
+		else
+			return "inband,an-disabled";
+	}
+
+	return "unknown";
+}
+
 static unsigned int phylink_interface_signal_rate(phy_interface_t interface)
 {
 	switch (interface) {
@@ -1164,7 +1182,9 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 	unsigned int neg_mode;
 	int err;
 
-	phylink_dbg(pl, "major config %s\n", phy_modes(state->interface));
+	phylink_dbg(pl, "major config, requested %s/%s\n",
+		    phylink_an_mode_str(pl->req_link_an_mode),
+		    phy_modes(state->interface));
 
 	if (pl->mac_ops->mac_select_pcs) {
 		pcs = pl->mac_ops->mac_select_pcs(pl->config, state->interface);
@@ -1180,6 +1200,11 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 
 	phylink_pcs_neg_mode(pl, pcs, state->interface, state->advertising);
 
+	phylink_dbg(pl, "major config, active %s/%s/%s\n",
+		    phylink_an_mode_str(pl->act_link_an_mode),
+		    phylink_pcs_mode_str(pl->pcs_neg_mode),
+		    phy_modes(state->interface));
+
 	phylink_pcs_poll_stop(pl);
 
 	if (pl->mac_ops->mac_prepare) {
-- 
2.30.2

[PATCH RFC net-next 04/16] net: phy: add phy_inband_caps()

[Russell King (Oracle)]

Add a method to query the PHY's in-band capabilities for a PHY
interface mode.

Where the interface mode does not have in-band capability, or the PHY
driver has not been updated to return this information, then
phy_inband_caps() should return zero. Otherwise, PHY drivers will
return a value consisting of the following flags:

LINK_INBAND_DISABLE indicates that the hardware does not support
in-band signalling, or can have in-band signalling configured via
software to be disabled.

LINK_INBAND_ENABLE indicates that the hardware will use in-band
signalling, or can have in-band signalling configured via software
to be enabled.

LINK_INBAND_BYPASS indicates that the hardware has the ability to
bypass in-band signalling when enabled after a timeout if the link
partner does not respond to its in-band signalling.

This reports the PHY capabilities for the particular interface mode,
not the current configuration.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phy.c | 21 +++++++++++++++++++++
 include/linux/phy.h   | 28 ++++++++++++++++++++++++++++
 2 files changed, 49 insertions(+)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 4f3e742907cb..d7b34f8ae415 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1005,6 +1005,27 @@ static int phy_check_link_status(struct phy_device *phydev)
 	return 0;
 }
 
+/**
+ * phy_inband_caps - query which in-band signalling modes are supported
+ * @phydev: a pointer to a &struct phy_device
+ * @interface: the interface mode for the PHY
+ *
+ * Returns zero if it is unknown what in-band signalling is supported by the
+ * PHY (e.g. because the PHY driver doesn't implement the method.) Otherwise,
+ * returns a bit mask of the LINK_INBAND_* values from
+ * &enum link_inband_signalling to describe which inband modes are supported
+ * by the PHY for this interface mode.
+ */
+unsigned int phy_inband_caps(struct phy_device *phydev,
+			     phy_interface_t interface)
+{
+	if (phydev->drv && phydev->drv->inband_caps)
+		return phydev->drv->inband_caps(phydev, interface);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(phy_inband_caps);
+
 /**
  * _phy_start_aneg - start auto-negotiation for this PHY device
  * @phydev: the phy_device struct
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 77c6d6451638..ff60c4785e11 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -815,6 +815,24 @@ struct phy_tdr_config {
 };
 #define PHY_PAIR_ALL -1
 
+/**
+ * enum link_inband_signalling - in-band signalling modes that are supported
+ *
+ * @LINK_INBAND_DISABLE: in-band signalling can be disabled
+ * @LINK_INBAND_ENABLE: in-band signalling can be enabled without bypass
+ * @LINK_INBAND_BYPASS: in-band signalling can be enabled with bypass
+ *
+ * The possible and required bits can only be used if the valid bit is set.
+ * If possible is clear, that means inband signalling can not be used.
+ * Required is only valid when possible is set, and means that inband
+ * signalling must be used.
+ */
+enum link_inband_signalling {
+	LINK_INBAND_DISABLE		= BIT(0),
+	LINK_INBAND_ENABLE		= BIT(1),
+	LINK_INBAND_BYPASS		= BIT(2),
+};
+
 /**
  * struct phy_plca_cfg - Configuration of the PLCA (Physical Layer Collision
  * Avoidance) Reconciliation Sublayer.
@@ -954,6 +972,14 @@ struct phy_driver {
 	 */
 	int (*get_features)(struct phy_device *phydev);
 
+	/**
+	 * @inband_caps: query whether in-band is supported for the given PHY
+	 * interface mode. Returns a bitmask of bits defined by enum
+	 * link_inband_signalling.
+	 */
+	unsigned int (*inband_caps)(struct phy_device *phydev,
+				    phy_interface_t interface);
+
 	/**
 	 * @get_rate_matching: Get the supported type of rate matching for a
 	 * particular phy interface. This is used by phy consumers to determine
@@ -1816,6 +1842,8 @@ int phy_config_aneg(struct phy_device *phydev);
 int _phy_start_aneg(struct phy_device *phydev);
 int phy_start_aneg(struct phy_device *phydev);
 int phy_aneg_done(struct phy_device *phydev);
+unsigned int phy_inband_caps(struct phy_device *phydev,
+			     phy_interface_t interface);
 int phy_speed_down(struct phy_device *phydev, bool sync);
 int phy_speed_up(struct phy_device *phydev);
 bool phy_check_valid(int speed, int duplex, unsigned long *features);
-- 
2.30.2

[PATCH RFC net-next 05/16] net: phy: bcm84881: implement phy_inband_caps() method

[Russell King (Oracle)]

BCM84881 has no support for inband signalling, so this is a trivial
implementation that returns no support for inband.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/bcm84881.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/net/phy/bcm84881.c b/drivers/net/phy/bcm84881.c
index 97da3aee4942..47405bded677 100644
--- a/drivers/net/phy/bcm84881.c
+++ b/drivers/net/phy/bcm84881.c
@@ -235,11 +235,21 @@ static int bcm84881_read_status(struct phy_device *phydev)
 	return genphy_c45_read_mdix(phydev);
 }
 
+/* The Broadcom BCM84881 in the Methode DM7052 is unable to provide a SGMII
+ * or 802.3z control word, so inband will not work.
+ */
+static unsigned int bcm84881_inband_caps(struct phy_device *phydev,
+					 phy_interface_t interface)
+{
+	return LINK_INBAND_DISABLE;
+}
+
 static struct phy_driver bcm84881_drivers[] = {
 	{
 		.phy_id		= 0xae025150,
 		.phy_id_mask	= 0xfffffff0,
 		.name		= "Broadcom BCM84881",
+		.inband_caps	= bcm84881_inband_caps,
 		.config_init	= bcm84881_config_init,
 		.probe		= bcm84881_probe,
 		.get_features	= bcm84881_get_features,
-- 
2.30.2

[PATCH RFC net-next 06/16] net: phy: marvell: implement phy_inband_caps() method

[Russell King (Oracle)]

Provide an implementation for phy_inband_caps() for Marvell PHYs used
on SFP modules, so that phylink knows the PHYs capabilities.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/marvell.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index cd50cd6a7f75..3075ebc3f964 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -717,6 +717,20 @@ static int marvell_config_aneg_fiber(struct phy_device *phydev)
 	return genphy_check_and_restart_aneg(phydev, changed);
 }
 
+static unsigned int m88e1111_inband_caps(struct phy_device *phydev,
+					 phy_interface_t interface)
+{
+	/* In 1000base-X and SGMII modes, the inband mode can be changed
+	 * through the Fibre page BMCR ANENABLE bit.
+	 */
+	if (interface == PHY_INTERFACE_MODE_1000BASEX ||
+	    interface == PHY_INTERFACE_MODE_SGMII)
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE |
+		       LINK_INBAND_BYPASS;
+
+	return 0;
+}
+
 static int m88e1111_config_aneg(struct phy_device *phydev)
 {
 	int extsr = phy_read(phydev, MII_M1111_PHY_EXT_SR);
@@ -3677,6 +3691,7 @@ static struct phy_driver marvell_drivers[] = {
 		.name = "Marvell 88E1112",
 		/* PHY_GBIT_FEATURES */
 		.probe = marvell_probe,
+		.inband_caps = m88e1111_inband_caps,
 		.config_init = m88e1112_config_init,
 		.config_aneg = marvell_config_aneg,
 		.config_intr = marvell_config_intr,
@@ -3698,6 +3713,7 @@ static struct phy_driver marvell_drivers[] = {
 		/* PHY_GBIT_FEATURES */
 		.flags = PHY_POLL_CABLE_TEST,
 		.probe = marvell_probe,
+		.inband_caps = m88e1111_inband_caps,
 		.config_init = m88e1111gbe_config_init,
 		.config_aneg = m88e1111_config_aneg,
 		.read_status = marvell_read_status,
@@ -3721,6 +3737,7 @@ static struct phy_driver marvell_drivers[] = {
 		.name = "Marvell 88E1111 (Finisar)",
 		/* PHY_GBIT_FEATURES */
 		.probe = marvell_probe,
+		.inband_caps = m88e1111_inband_caps,
 		.config_init = m88e1111gbe_config_init,
 		.config_aneg = m88e1111_config_aneg,
 		.read_status = marvell_read_status,
-- 
2.30.2

[PATCH RFC net-next 07/16] net: phy: add phy_config_inband()

[Russell King (Oracle)]

Add a method to configure the PHY's in-band mode.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phy.c | 31 +++++++++++++++++++++++++++++++
 include/linux/phy.h   |  6 ++++++
 2 files changed, 37 insertions(+)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index d7b34f8ae415..3e4922839895 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1026,6 +1026,37 @@ unsigned int phy_inband_caps(struct phy_device *phydev,
 }
 EXPORT_SYMBOL_GPL(phy_inband_caps);
 
+/**
+ * phy_config_inband - configure the desired PHY in-band mode
+ * @phydev: the phy_device struct
+ * @modes: in-band modes to configure
+ *
+ * Description: disables, enables or enables-with-bypass in-band signalling
+ *   between the PHY and host system.
+ *
+ * Returns: zero on success, or negative errno value.
+ */
+int phy_config_inband(struct phy_device *phydev, unsigned int modes)
+{
+	int err;
+
+	if (!!(modes & LINK_INBAND_DISABLE) +
+	    !!(modes & LINK_INBAND_ENABLE) +
+	    !!(modes & LINK_INBAND_BYPASS) != 1)
+		return -EINVAL;
+
+	mutex_lock(&phydev->lock);
+	if (!phydev->drv)
+		err = -EIO;
+	else if (!phydev->drv->config_inband)
+		err = -EOPNOTSUPP;
+	else
+		err = phydev->drv->config_inband(phydev, modes);
+	mutex_unlock(&phydev->lock);
+
+	return err;
+}
+
 /**
  * _phy_start_aneg - start auto-negotiation for this PHY device
  * @phydev: the phy_device struct
diff --git a/include/linux/phy.h b/include/linux/phy.h
index ff60c4785e11..6c1887d1edbf 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -980,6 +980,11 @@ struct phy_driver {
 	unsigned int (*inband_caps)(struct phy_device *phydev,
 				    phy_interface_t interface);
 
+	/**
+	 * @config_inband: configure in-band mode for the PHY
+	 */
+	int (*config_inband)(struct phy_device *phydev, unsigned int modes);
+
 	/**
 	 * @get_rate_matching: Get the supported type of rate matching for a
 	 * particular phy interface. This is used by phy consumers to determine
@@ -1844,6 +1849,7 @@ int phy_start_aneg(struct phy_device *phydev);
 int phy_aneg_done(struct phy_device *phydev);
 unsigned int phy_inband_caps(struct phy_device *phydev,
 			     phy_interface_t interface);
+int phy_config_inband(struct phy_device *phydev, unsigned int modes);
 int phy_speed_down(struct phy_device *phydev, bool sync);
 int phy_speed_up(struct phy_device *phydev);
 bool phy_check_valid(int speed, int duplex, unsigned long *features);
-- 
2.30.2

[PATCH RFC net-next 08/16] net: phy: marvell: implement config_inband() method

[Russell King (Oracle)]

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/marvell.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 3075ebc3f964..b885bc0fe6e0 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -731,6 +731,34 @@ static unsigned int m88e1111_inband_caps(struct phy_device *phydev,
 	return 0;
 }
 
+static int m88e1111_config_inband(struct phy_device *phydev, unsigned int modes)
+{
+	u16 extsr, bmcr;
+	int err;
+
+	if (phydev->interface != PHY_INTERFACE_MODE_1000BASEX &&
+	    phydev->interface != PHY_INTERFACE_MODE_SGMII)
+		return -EINVAL;
+
+	if (modes == LINK_INBAND_BYPASS)
+		extsr = MII_M1111_HWCFG_SERIAL_AN_BYPASS;
+	else
+		extsr = 0;
+
+	if (modes == LINK_INBAND_DISABLE)
+		bmcr = 0;
+	else
+		bmcr = BMCR_ANENABLE;
+
+	err = phy_modify(phydev, MII_M1111_PHY_EXT_SR,
+			 MII_M1111_HWCFG_SERIAL_AN_BYPASS, extsr);
+	if (err < 0)
+		return extsr;
+
+	return phy_modify_paged(phydev, MII_MARVELL_FIBER_PAGE, MII_BMCR,
+				BMCR_ANENABLE, bmcr);
+}
+
 static int m88e1111_config_aneg(struct phy_device *phydev)
 {
 	int extsr = phy_read(phydev, MII_M1111_PHY_EXT_SR);
@@ -3692,6 +3720,7 @@ static struct phy_driver marvell_drivers[] = {
 		/* PHY_GBIT_FEATURES */
 		.probe = marvell_probe,
 		.inband_caps = m88e1111_inband_caps,
+		.config_inband = m88e1111_config_inband,
 		.config_init = m88e1112_config_init,
 		.config_aneg = marvell_config_aneg,
 		.config_intr = marvell_config_intr,
@@ -3714,6 +3743,7 @@ static struct phy_driver marvell_drivers[] = {
 		.flags = PHY_POLL_CABLE_TEST,
 		.probe = marvell_probe,
 		.inband_caps = m88e1111_inband_caps,
+		.config_inband = m88e1111_config_inband,
 		.config_init = m88e1111gbe_config_init,
 		.config_aneg = m88e1111_config_aneg,
 		.read_status = marvell_read_status,
@@ -3738,6 +3768,7 @@ static struct phy_driver marvell_drivers[] = {
 		/* PHY_GBIT_FEATURES */
 		.probe = marvell_probe,
 		.inband_caps = m88e1111_inband_caps,
+		.config_inband = m88e1111_config_inband,
 		.config_init = m88e1111gbe_config_init,
 		.config_aneg = m88e1111_config_aneg,
 		.read_status = marvell_read_status,
-- 
2.30.2

[PATCH RFC net-next 09/16] net: phylink: add pcs_inband_caps() method

[Russell King (Oracle)]

Add a pcs_inband_caps() method to query the PCS for its inband link
capabilities, and use this to determine whether link modes used with
optical SFPs can be supported.

When a PCS does not provide a method, we allow inband negotiation to
be either on or off, making this a no-op until the pcs_inband_caps()
method is implemented by a PCS driver.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 60 +++++++++++++++++++++++++++++++++++++++
 include/linux/phylink.h   | 17 +++++++++++
 2 files changed, 77 insertions(+)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index e43a083cec57..ca52cb23187d 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -990,6 +990,15 @@ static void phylink_resolve_an_pause(struct phylink_link_state *state)
 	}
 }
 
+static unsigned int phylink_pcs_inband_caps(struct phylink_pcs *pcs,
+				    phy_interface_t interface)
+{
+	if (pcs && pcs->ops->pcs_inband_caps)
+		return pcs->ops->pcs_inband_caps(pcs, interface);
+
+	return 0;
+}
+
 static void phylink_pcs_pre_config(struct phylink_pcs *pcs,
 				   phy_interface_t interface)
 {
@@ -1043,6 +1052,24 @@ static void phylink_pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode,
 		pcs->ops->pcs_link_up(pcs, neg_mode, interface, speed, duplex);
 }
 
+/* Query inband for a specific interface mode, asking the MAC for the
+ * PCS which will be used to handle the interface mode.
+ */
+static unsigned int phylink_inband_caps(struct phylink *pl,
+					 phy_interface_t interface)
+{
+	struct phylink_pcs *pcs;
+
+	if (!pl->mac_ops->mac_select_pcs)
+		return 0;
+
+	pcs = pl->mac_ops->mac_select_pcs(pl->config, interface);
+	if (!pcs)
+		return 0;
+
+	return phylink_pcs_inband_caps(pcs, interface);
+}
+
 static void phylink_pcs_poll_stop(struct phylink *pl)
 {
 	if (pl->cfg_link_an_mode == MLO_AN_INBAND)
@@ -2541,6 +2568,26 @@ int phylink_ethtool_ksettings_get(struct phylink *pl,
 }
 EXPORT_SYMBOL_GPL(phylink_ethtool_ksettings_get);
 
+static bool phylink_validate_pcs_inband_autoneg(struct phylink *pl,
+					        phy_interface_t interface,
+						unsigned long *adv)
+{
+	unsigned int inband = phylink_inband_caps(pl, interface);
+	unsigned int mask;
+
+	/* If the PCS doesn't implement inband support, be permissive. */
+	if (!inband)
+		return true;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, adv))
+		mask = LINK_INBAND_ENABLE;
+	else
+		mask = LINK_INBAND_DISABLE;
+
+	/* Check whether the PCS implements the required mode */
+	return !!(inband & mask);
+}
+
 /**
  * phylink_ethtool_ksettings_set() - set the link settings
  * @pl: a pointer to a &struct phylink returned from phylink_create()
@@ -2671,6 +2718,13 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 	    phylink_is_empty_linkmode(config.advertising))
 		return -EINVAL;
 
+	/* Validate the autonegotiation state. We don't have a PHY in this
+	 * situation, so the PCS is the media-facing entity.
+	 */
+	if (!phylink_validate_pcs_inband_autoneg(pl, config.interface,
+						 config.advertising))
+		return -EINVAL;
+
 	mutex_lock(&pl->state_mutex);
 	pl->link_config.speed = config.speed;
 	pl->link_config.duplex = config.duplex;
@@ -3350,6 +3404,12 @@ static int phylink_sfp_config_optical(struct phylink *pl)
 	phylink_dbg(pl, "optical SFP: chosen %s interface\n",
 		    phy_modes(interface));
 
+	if (!phylink_validate_pcs_inband_autoneg(pl, interface,
+						 config.advertising)) {
+		phylink_err(pl, "autoneg setting not compatible with PCS");
+		return -EINVAL;
+	}
+
 	config.interface = interface;
 
 	/* Ignore errors if we're expecting a PHY to attach later */
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 595139797acb..ef26111d0040 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -422,6 +422,7 @@ struct phylink_pcs {
 /**
  * struct phylink_pcs_ops - MAC PCS operations structure.
  * @pcs_validate: validate the link configuration.
+ * @pcs_inband_caps: query inband support for interface mode.
  * @pcs_enable: enable the PCS.
  * @pcs_disable: disable the PCS.
  * @pcs_pre_config: pre-mac_config method (for errata)
@@ -437,6 +438,8 @@ struct phylink_pcs {
 struct phylink_pcs_ops {
 	int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported,
 			    const struct phylink_link_state *state);
+	unsigned int (*pcs_inband_caps)(struct phylink_pcs *pcs,
+					phy_interface_t interface);
 	int (*pcs_enable)(struct phylink_pcs *pcs);
 	void (*pcs_disable)(struct phylink_pcs *pcs);
 	void (*pcs_pre_config)(struct phylink_pcs *pcs,
@@ -473,6 +476,20 @@ struct phylink_pcs_ops {
 int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
 		 const struct phylink_link_state *state);
 
+/**
+ * pcs_inband_caps - query PCS in-band capabilities for interface mode.
+ * @pcs: a pointer to a &struct phylink_pcs.
+ * @interface: interface mode to be queried
+ *
+ * Returns zero if it is unknown what in-band signalling is supported by the
+ * PHY (e.g. because the PHY driver doesn't implement the method.) Otherwise,
+ * returns a bit mask of the LINK_INBAND_* values from
+ * &enum link_inband_signalling to describe which inband modes are supported
+ * for this interface mode.
+ */
+unsigned int pcs_inband_caps(struct phylink_pcs *pcs,
+			     phy_interface_t interface);
+
 /**
  * pcs_enable() - enable the PCS.
  * @pcs: a pointer to a &struct phylink_pcs.
-- 
2.30.2

[PATCH RFC net-next 10/16] net: mvneta: implement pcs_inband_caps() method

[Russell King (Oracle)]

Report the PCS in-band capabilities to phylink for Marvell NETA
interfaces.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/marvell/mvneta.c | 27 +++++++++++++++++----------
 1 file changed, 17 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 1fb285fa0bdb..fe6261b81540 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3960,20 +3960,27 @@ static struct mvneta_port *mvneta_pcs_to_port(struct phylink_pcs *pcs)
 	return container_of(pcs, struct mvneta_port, phylink_pcs);
 }
 
-static int mvneta_pcs_validate(struct phylink_pcs *pcs,
-			       unsigned long *supported,
-			       const struct phylink_link_state *state)
+static unsigned int mvneta_pcs_inband_caps(struct phylink_pcs *pcs,
+					   phy_interface_t interface)
 {
-	/* We only support QSGMII, SGMII, 802.3z and RGMII modes.
-	 * When in 802.3z mode, we must have AN enabled:
+	/* When operating in an 802.3z mode, we must have AN enabled:
 	 * "Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
 	 * When <PortType> = 1 (1000BASE-X) this field must be set to 1."
+	 * Therefore, inband is "required".
 	 */
-	if (phy_interface_mode_is_8023z(state->interface) &&
-	    !phylink_test(state->advertising, Autoneg))
-		return -EINVAL;
+	if (phy_interface_mode_is_8023z(interface))
+		return LINK_INBAND_ENABLE;
 
-	return 0;
+	/* QSGMII, SGMII and RGMII can be configured to use inband
+	 * signalling of the AN result. Indicate these as "possible".
+	 */
+	if (interface == PHY_INTERFACE_MODE_SGMII ||
+	    interface == PHY_INTERFACE_MODE_QSGMII ||
+	    phy_interface_mode_is_rgmii(interface))
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	/* For any other modes, indicate that inband is not supported. */
+	return LINK_INBAND_DISABLE;
 }
 
 static void mvneta_pcs_get_state(struct phylink_pcs *pcs,
@@ -4071,7 +4078,7 @@ static void mvneta_pcs_an_restart(struct phylink_pcs *pcs)
 }
 
 static const struct phylink_pcs_ops mvneta_phylink_pcs_ops = {
-	.pcs_validate = mvneta_pcs_validate,
+	.pcs_inband_caps = mvneta_pcs_inband_caps,
 	.pcs_get_state = mvneta_pcs_get_state,
 	.pcs_config = mvneta_pcs_config,
 	.pcs_an_restart = mvneta_pcs_an_restart,
-- 
2.30.2

[PATCH RFC net-next 11/16] net: mvpp2: implement pcs_inband_caps() method

[Russell King (Oracle)]

Report the PCS in-band capabilities to phylink for Marvell PP2
interfaces.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/marvell/mvpp2/mvpp2_main.c   | 25 ++++++++++++-------
 1 file changed, 16 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 571631a30320..f85229a30844 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6224,19 +6224,26 @@ static const struct phylink_pcs_ops mvpp2_phylink_xlg_pcs_ops = {
 	.pcs_config = mvpp2_xlg_pcs_config,
 };
 
-static int mvpp2_gmac_pcs_validate(struct phylink_pcs *pcs,
-				   unsigned long *supported,
-				   const struct phylink_link_state *state)
+static unsigned int mvpp2_gmac_pcs_inband_caps(struct phylink_pcs *pcs,
+					       phy_interface_t interface)
 {
-	/* When in 802.3z mode, we must have AN enabled:
+	/* When operating in an 802.3z mode, we must have AN enabled:
 	 * Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
 	 * When <PortType> = 1 (1000BASE-X) this field must be set to 1.
+	 * Therefore, inband is "required".
 	 */
-	if (phy_interface_mode_is_8023z(state->interface) &&
-	    !phylink_test(state->advertising, Autoneg))
-		return -EINVAL;
+	if (phy_interface_mode_is_8023z(interface))
+		return LINK_INBAND_ENABLE;
 
-	return 0;
+	/* SGMII and RGMII can be configured to use inband signalling of the
+	 * AN result. Indicate these as "possible".
+	 */
+	if (interface == PHY_INTERFACE_MODE_SGMII ||
+	    phy_interface_mode_is_rgmii(interface))
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	/* For any other modes, indicate that inband is not supported. */
+	return LINK_INBAND_DISABLE;
 }
 
 static void mvpp2_gmac_pcs_get_state(struct phylink_pcs *pcs,
@@ -6343,7 +6350,7 @@ static void mvpp2_gmac_pcs_an_restart(struct phylink_pcs *pcs)
 }
 
 static const struct phylink_pcs_ops mvpp2_phylink_gmac_pcs_ops = {
-	.pcs_validate = mvpp2_gmac_pcs_validate,
+	.pcs_inband_caps = mvpp2_gmac_pcs_inband_caps,
 	.pcs_get_state = mvpp2_gmac_pcs_get_state,
 	.pcs_config = mvpp2_gmac_pcs_config,
 	.pcs_an_restart = mvpp2_gmac_pcs_an_restart,
-- 
2.30.2

[PATCH RFC net-next 12/16] net: pcs: pcs-lynx: implement pcs_inband_caps() method

[Russell King (Oracle)]

Report the PCS in-band capabilities to phylink for the Lynx PCS.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/pcs/pcs-lynx.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/net/pcs/pcs-lynx.c b/drivers/net/pcs/pcs-lynx.c
index b79aedad855b..767a8c0714ac 100644
--- a/drivers/net/pcs/pcs-lynx.c
+++ b/drivers/net/pcs/pcs-lynx.c
@@ -35,6 +35,27 @@ enum sgmii_speed {
 #define phylink_pcs_to_lynx(pl_pcs) container_of((pl_pcs), struct lynx_pcs, pcs)
 #define lynx_to_phylink_pcs(lynx) (&(lynx)->pcs)
 
+static unsigned int lynx_pcs_inband_caps(struct phylink_pcs *pcs,
+					 phy_interface_t interface)
+{
+	switch (interface) {
+	case PHY_INTERFACE_MODE_1000BASEX:
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	case PHY_INTERFACE_MODE_10GBASER:
+	case PHY_INTERFACE_MODE_2500BASEX:
+		return LINK_INBAND_DISABLE;
+
+	case PHY_INTERFACE_MODE_USXGMII:
+		return LINK_INBAND_ENABLE;
+
+	default:
+		return 0;
+	}
+}
+
 static void lynx_pcs_get_state_usxgmii(struct mdio_device *pcs,
 				       struct phylink_link_state *state)
 {
@@ -306,6 +327,7 @@ static void lynx_pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode,
 }
 
 static const struct phylink_pcs_ops lynx_pcs_phylink_ops = {
+	.pcs_inband_caps = lynx_pcs_inband_caps,
 	.pcs_get_state = lynx_pcs_get_state,
 	.pcs_config = lynx_pcs_config,
 	.pcs_an_restart = lynx_pcs_an_restart,
-- 
2.30.2

[PATCH RFC net-next 13/16] net: pcs: pcs-mtk-lynxi: implement pcs_inband_caps() method

[Russell King (Oracle)]

Report the PCS in-band capabilities to phylink for the LynxI PCS.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/pcs/pcs-mtk-lynxi.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/net/pcs/pcs-mtk-lynxi.c b/drivers/net/pcs/pcs-mtk-lynxi.c
index 4f63abe638c4..7de804535229 100644
--- a/drivers/net/pcs/pcs-mtk-lynxi.c
+++ b/drivers/net/pcs/pcs-mtk-lynxi.c
@@ -88,6 +88,21 @@ static struct mtk_pcs_lynxi *pcs_to_mtk_pcs_lynxi(struct phylink_pcs *pcs)
 	return container_of(pcs, struct mtk_pcs_lynxi, pcs);
 }
 
+static unsigned int mtk_pcs_lynxi_inband_caps(struct phylink_pcs *pcs,
+					      phy_interface_t interface)
+{
+	switch (interface) {
+	case PHY_INTERFACE_MODE_1000BASEX:
+	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	default:
+		return 0;
+	}
+}
+
 static void mtk_pcs_lynxi_get_state(struct phylink_pcs *pcs,
 				    struct phylink_link_state *state)
 {
@@ -241,6 +256,7 @@ static void mtk_pcs_lynxi_disable(struct phylink_pcs *pcs)
 }
 
 static const struct phylink_pcs_ops mtk_pcs_lynxi_ops = {
+	.pcs_inband_caps = mtk_pcs_lynxi_inband_caps,
 	.pcs_get_state = mtk_pcs_lynxi_get_state,
 	.pcs_config = mtk_pcs_lynxi_config,
 	.pcs_an_restart = mtk_pcs_lynxi_restart_an,
-- 
2.30.2

[PATCH RFC net-next 14/16] net: pcs: xpcs: implement pcs_inband_caps() method

[Russell King (Oracle)]

Report the PCS inband capabilities to phylink for XPCS.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/pcs/pcs-xpcs.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
index 7246a910728d..f70ca39f0905 100644
--- a/drivers/net/pcs/pcs-xpcs.c
+++ b/drivers/net/pcs/pcs-xpcs.c
@@ -567,6 +567,33 @@ static int xpcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
 	return 0;
 }
 
+static unsigned int xpcs_inband_caps(struct phylink_pcs *pcs,
+				     phy_interface_t interface)
+{
+	struct dw_xpcs *xpcs = phylink_pcs_to_xpcs(pcs);
+	const struct dw_xpcs_compat *compat;
+
+	compat = xpcs_find_compat(xpcs, interface);
+	if (!compat)
+		return 0;
+
+	switch (compat->an_mode) {
+	case DW_AN_C73:
+		return LINK_INBAND_ENABLE;
+
+	case DW_AN_C37_SGMII:
+	case DW_AN_C37_1000BASEX:
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+
+	case DW_10GBASER:
+	case DW_2500BASEX:
+		return LINK_INBAND_DISABLE;
+
+	default:
+		return 0;
+	}
+}
+
 void xpcs_get_interfaces(struct dw_xpcs *xpcs, unsigned long *interfaces)
 {
 	const struct dw_xpcs_compat *compat;
@@ -1306,6 +1333,7 @@ static const struct dw_xpcs_desc xpcs_desc_list[] = {
 
 static const struct phylink_pcs_ops xpcs_phylink_ops = {
 	.pcs_validate = xpcs_validate,
+	.pcs_inband_caps = xpcs_inband_caps,
 	.pcs_pre_config = xpcs_pre_config,
 	.pcs_config = xpcs_config,
 	.pcs_get_state = xpcs_get_state,
-- 
2.30.2

[PATCH RFC net-next 15/16] net: phylink: add negotiation of in-band capabilities

[Russell King (Oracle)]

Support for in-band signalling with Serdes links is uncertain. Some
PHYs do not support in-band for e.g. SGMII. Some PCS do not support
in-band for 2500Base-X. Some PCS require in-band for Base-X protocols.

Simply using what is in DT is insufficient when we have hot-pluggable
PHYs e.g. in the form of SFP modules, which may not provide the
in-band signalling.

In order to address this, we have introduced phy_inband_caps() and
pcs_inband_caps() functions to allow phylink to retrieve the
capabilities from each end of the PCS/PHY link. This commit adds code
to resolve whether in-band will be used in the various scenarios that
we have: In-band not being used, PHY present using SGMII or Base-X,
PHY not present. We also deal with no capabilties provided.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 154 +++++++++++++++++++++++++++++++++++---
 1 file changed, 144 insertions(+), 10 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index ca52cb23187d..fd2855fc0fc8 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -75,6 +75,7 @@ struct phylink {
 
 	struct mutex state_mutex;
 	struct phylink_link_state phy_state;
+	unsigned int phy_ib_mode;
 	struct work_struct resolve;
 	unsigned int pcs_neg_mode;
 	unsigned int pcs_state;
@@ -1153,10 +1154,18 @@ static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
 				 phy_interface_t interface,
 				 const unsigned long *advertising)
 {
+	unsigned int pcs_ib_caps = 0;
+	unsigned int phy_ib_caps = 0;
 	unsigned int neg_mode, mode;
+	enum {
+		INBAND_CISCO_SGMII,
+		INBAND_BASEX,
+	} type;
 
 	mode = pl->req_link_an_mode;
 
+	pl->phy_ib_mode = 0;
+
 	switch (interface) {
 	case PHY_INTERFACE_MODE_SGMII:
 	case PHY_INTERFACE_MODE_QSGMII:
@@ -1168,10 +1177,7 @@ static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
 		 * inband communication. Note: there exist PHYs that run
 		 * with SGMII but do not send the inband data.
 		 */
-		if (!phylink_autoneg_inband(mode))
-			neg_mode = PHYLINK_PCS_NEG_OUTBAND;
-		else
-			neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
+		type = INBAND_CISCO_SGMII;
 		break;
 
 	case PHY_INTERFACE_MODE_1000BASEX:
@@ -1182,18 +1188,139 @@ static void phylink_pcs_neg_mode(struct phylink *pl, struct phylink_pcs *pcs,
 		 * as well, but drivers may not support this, so may
 		 * need to override this.
 		 */
-		if (!phylink_autoneg_inband(mode))
+		type = INBAND_BASEX;
+		break;
+
+	default:
+		pl->pcs_neg_mode = PHYLINK_PCS_NEG_NONE;
+		pl->act_link_an_mode = mode;
+		return;
+	}
+
+	if (pcs)
+		pcs_ib_caps = phylink_pcs_inband_caps(pcs, interface);
+
+	if (pl->phydev)
+		phy_ib_caps = phy_inband_caps(pl->phydev, interface);
+
+	phylink_dbg(pl, "interface %s inband modes: pcs=%02x phy=%02x\n",
+		    phy_modes(interface), pcs_ib_caps, phy_ib_caps);
+
+	if (!phylink_autoneg_inband(mode)) {
+		bool pcs_ib_only = false;
+		bool phy_ib_only = false;
+
+		if (pcs_ib_caps && pcs_ib_caps != LINK_INBAND_DISABLE) {
+			/* PCS supports reporting in-band capabilities, and
+			 * supports more than disable mode.
+			 */
+			if (pcs_ib_caps & LINK_INBAND_DISABLE)
+				neg_mode = PHYLINK_PCS_NEG_OUTBAND;
+			else if (pcs_ib_caps & LINK_INBAND_ENABLE)
+				pcs_ib_only = true;
+		}
+
+		if (phy_ib_caps && phy_ib_caps != LINK_INBAND_DISABLE) {
+			/* PHY supports in-band capabilities, and supports
+			 * more than disable mode.
+			 */
+			if (phy_ib_caps & LINK_INBAND_DISABLE)
+				pl->phy_ib_mode = LINK_INBAND_DISABLE;
+			else if (phy_ib_caps & LINK_INBAND_BYPASS)
+				pl->phy_ib_mode = LINK_INBAND_BYPASS;
+			else if (phy_ib_caps & LINK_INBAND_ENABLE)
+				phy_ib_only = true;
+		}
+
+		/* If either the PCS or PHY requires inband to be enabled,
+		 * this is an invalid configuration. Provide a diagnostic
+		 * message for this case, but don't try to force the issue.
+		 */
+		if (pcs_ib_only || phy_ib_only)
+			phylink_warn(pl,
+				     "firmware wants %s mode, but %s%s%s requires inband\n",
+				     phylink_an_mode_str(mode),
+				     pcs_ib_only ? "PCS" : "",
+				     pcs_ib_only && phy_ib_only ? " and " : "",
+				     phy_ib_only ? "PHY" : "");
+
+		neg_mode = PHYLINK_PCS_NEG_OUTBAND;
+	} else if (type == INBAND_CISCO_SGMII || pl->phydev) {
+		/* For SGMII modes which are designed to be used with PHYs, or
+		 * Base-X with a PHY, we try to use in-band mode where-ever
+		 * possible. However, there are some PHYs e.g. BCM84881 which
+		 * do not support in-band.
+		 */
+		const unsigned int inband_ok = LINK_INBAND_ENABLE |
+					       LINK_INBAND_BYPASS;
+		const unsigned int outband_ok = LINK_INBAND_DISABLE |
+						LINK_INBAND_BYPASS;
+		/* PCS	PHY
+		 * D E	D E
+		 * 0 0  0 0	no information			inband enabled
+		 * 1 0  0 0	pcs doesn't support		outband
+		 * 0 1  0 0	pcs required			inband enabled
+		 * 1 1  0 0	pcs optional			inband enabled
+		 * 0 0  1 0	phy doesn't support		outband
+		 * 1 0  1 0	pcs+phy doesn't support		outband
+		 * 0 1  1 0	pcs required, phy doesn't support, invalid
+		 * 1 1  1 0	pcs optional, phy doesn't support, outband
+		 * 0 0  0 1	phy required			inband enabled
+		 * 1 0  0 1	pcs doesn't support, phy required, invalid
+		 * 0 1  0 1	pcs+phy required		inband enabled
+		 * 1 1  0 1	pcs optional, phy required	inband enabled
+		 * 0 0  1 1	phy optional			inband enabled
+		 * 1 0  1 1	pcs doesn't support, phy optional, outband
+		 * 0 1  1 1	pcs required, phy optional	inband enabled
+		 * 1 1  1 1	pcs+phy optional		inband enabled
+		 */
+		if ((!pcs_ib_caps || pcs_ib_caps & inband_ok) &&
+		    (!phy_ib_caps || phy_ib_caps & inband_ok)) {
+			/* In-band supported or unknown at both ends. Enable
+			 * in-band mode with or without bypass at the PHY.
+			 */
+			if (phy_ib_caps & LINK_INBAND_ENABLE)
+				pl->phy_ib_mode = LINK_INBAND_ENABLE;
+			else if (phy_ib_caps & LINK_INBAND_BYPASS)
+				pl->phy_ib_mode = LINK_INBAND_BYPASS;
+
+			neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
+		} else if ((!pcs_ib_caps || pcs_ib_caps & outband_ok) &&
+			   (!phy_ib_caps || phy_ib_caps & outband_ok)) {
+			/* Either in-band not supported at at least one end.
+			 * In-band bypass at the other end is possible.
+			 */
+			if (phy_ib_caps & LINK_INBAND_DISABLE)
+				pl->phy_ib_mode = LINK_INBAND_DISABLE;
+			else if (phy_ib_caps & LINK_INBAND_BYPASS)
+				pl->phy_ib_mode = LINK_INBAND_BYPASS;
+
 			neg_mode = PHYLINK_PCS_NEG_OUTBAND;
+			if (pl->phydev)
+				mode = MLO_AN_PHY;
+		} else {
+			/* invalid */
+			phylink_warn(pl, "%s: incompatible in-band capabilities, trying in-band",
+				     phy_modes(interface));
+			neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
+		}
+	} else {
+		/* For Base-X without a PHY */
+		if (pcs_ib_caps == LINK_INBAND_DISABLE)
+			/* If the PCS doesn't support inband, then inband must
+			 * be disabled.
+			 */
+			neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED;
+		else if (pcs_ib_caps == LINK_INBAND_ENABLE)
+			/* If the PCS requires inband, then inband must always
+			 * be enabled.
+			 */
+			neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
 		else if (linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 					   advertising))
 			neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
 		else
 			neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED;
-		break;
-
-	default:
-		neg_mode = PHYLINK_PCS_NEG_NONE;
-		break;
 	}
 
 	pl->pcs_neg_mode = neg_mode;
@@ -1292,6 +1419,13 @@ static void phylink_major_config(struct phylink *pl, bool restart,
 				    ERR_PTR(err));
 	}
 
+	if (pl->phydev && pl->phy_ib_mode) {
+		err = phy_config_inband(pl->phydev, pl->phy_ib_mode);
+		if (err < 0)
+			phylink_err(pl, "phy_config_inband: %pe\n",
+				    ERR_PTR(err));
+	}
+
 	if (pl->sfp_bus) {
 		rate_kbd = phylink_interface_signal_rate(state->interface);
 		if (rate_kbd)
-- 
2.30.2

[PATCH RFC net-next 16/16] net: phylink: remove phylink_phy_no_inband()

[Russell King (Oracle)]

Remove phylink_phy_no_inband() now that we are handling the lack of
inband negotiation by querying the capabilities of the PHY and PCS,
and the BCM84881 PHY driver provides us the information necessary to
make the decision.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 27 ++++++---------------------
 1 file changed, 6 insertions(+), 21 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index fd2855fc0fc8..7d5ebab0afb1 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -3400,10 +3400,11 @@ static phy_interface_t phylink_choose_sfp_interface(struct phylink *pl,
 	return interface;
 }
 
-static void phylink_sfp_set_config(struct phylink *pl, u8 mode,
+static void phylink_sfp_set_config(struct phylink *pl,
 				   unsigned long *supported,
 				   struct phylink_link_state *state)
 {
+	u8 mode = MLO_AN_INBAND;
 	bool changed = false;
 
 	phylink_dbg(pl, "requesting link mode %s/%s with support %*pb\n",
@@ -3437,8 +3438,7 @@ static void phylink_sfp_set_config(struct phylink *pl, u8 mode,
 		phylink_mac_initial_config(pl, false);
 }
 
-static int phylink_sfp_config_phy(struct phylink *pl, u8 mode,
-				  struct phy_device *phy)
+static int phylink_sfp_config_phy(struct phylink *pl, struct phy_device *phy)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(support);
 	struct phylink_link_state config;
@@ -3482,7 +3482,7 @@ static int phylink_sfp_config_phy(struct phylink *pl, u8 mode,
 
 	pl->link_port = pl->sfp_port;
 
-	phylink_sfp_set_config(pl, mode, support, &config);
+	phylink_sfp_set_config(pl, support, &config);
 
 	return 0;
 }
@@ -3557,7 +3557,7 @@ static int phylink_sfp_config_optical(struct phylink *pl)
 
 	pl->link_port = pl->sfp_port;
 
-	phylink_sfp_set_config(pl, MLO_AN_INBAND, pl->sfp_support, &config);
+	phylink_sfp_set_config(pl, pl->sfp_support, &config);
 
 	return 0;
 }
@@ -3628,19 +3628,9 @@ static void phylink_sfp_link_up(void *upstream)
 	phylink_enable_and_run_resolve(pl, PHYLINK_DISABLE_LINK);
 }
 
-/* The Broadcom BCM84881 in the Methode DM7052 is unable to provide a SGMII
- * or 802.3z control word, so inband will not work.
- */
-static bool phylink_phy_no_inband(struct phy_device *phy)
-{
-	return phy->is_c45 && phy_id_compare(phy->c45_ids.device_ids[1],
-					     0xae025150, 0xfffffff0);
-}
-
 static int phylink_sfp_connect_phy(void *upstream, struct phy_device *phy)
 {
 	struct phylink *pl = upstream;
-	u8 mode;
 
 	/*
 	 * This is the new way of dealing with flow control for PHYs,
@@ -3651,17 +3641,12 @@ static int phylink_sfp_connect_phy(void *upstream, struct phy_device *phy)
 	 */
 	phy_support_asym_pause(phy);
 
-	if (phylink_phy_no_inband(phy))
-		mode = MLO_AN_PHY;
-	else
-		mode = MLO_AN_INBAND;
-
 	/* Set the PHY's host supported interfaces */
 	phy_interface_and(phy->host_interfaces, phylink_sfp_interfaces,
 			  pl->config->supported_interfaces);
 
 	/* Do the initial configuration */
-	return phylink_sfp_config_phy(pl, mode, phy);
+	return phylink_sfp_config_phy(pl, phy);
 }
 
 static void phylink_sfp_disconnect_phy(void *upstream,
-- 
2.30.2

Re: [PATCH RFC net-next 01/16] net: phylink: pass phylink and pcs into phylink_pcs_neg_mode()

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:20AM +0000, Russell King (Oracle) wrote:
> Move the call to phylink_pcs_neg_mode() in phylink_major_config() after
> we have selected the appropriate PCS to allow the PCS to be passed in.
> 
> Add struct phylink and struct phylink_pcs pointers to
> phylink_pcs_neg_mode() and pass in the appropriate structures. Set
> pl->pcs_neg_mode before returning, and remove the return value.
> 
> This will allow the capabilities of the PCS and any PHY to be used when
> deciding which pcs_neg_mode should be used.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 02/16] net: phylink: split cur_link_an_mode into requested and active

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:25AM +0000, Russell King (Oracle) wrote:
> There is an interdependence between the current link_an_mode and
> pcs_neg_mode that some drivers rely upon to know whether inband or PHY
> mode will be used.
> 
> In order to support detection of PCS and PHY inband capabilities
> resulting in automatic selection of inband or PHY mode, we need to
> cater for this, and support changing the MAC link_an_mode. However, we
> end up with an inter-dependency between the current link_an_mode and
> pcs_neg_mode.
> 
> To solve this, split the current link_an_mode into the requested
> link_an_mode and active link_an_mode. The requested link_an_mode will
> always be passed to phylink_pcs_neg_mode(), and the active link_an_mode
> will be used for everything else, and only updated during
> phylink_major_config(). This will ensure that phylink_pcs_neg_mode()'s
> link_an_mode will not depend on the active link_an_mode that will,
> in a future patch, depend on pcs_neg_mode.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 03/16] net: phylink: add debug for phylink_major_config()

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:30AM +0000, Russell King (Oracle) wrote:
> Now that we have a more complexity in phylink_major_config(), augment
> the debugging so we can see what's going on there.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 04/16] net: phy: add phy_inband_caps()

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:35AM +0000, Russell King (Oracle) wrote:
> Add a method to query the PHY's in-band capabilities for a PHY
> interface mode.
> 
> Where the interface mode does not have in-band capability, or the PHY
> driver has not been updated to return this information, then
> phy_inband_caps() should return zero. Otherwise, PHY drivers will
> return a value consisting of the following flags:
> 
> LINK_INBAND_DISABLE indicates that the hardware does not support
> in-band signalling, or can have in-band signalling configured via
> software to be disabled.
> 
> LINK_INBAND_ENABLE indicates that the hardware will use in-band
> signalling, or can have in-band signalling configured via software
> to be enabled.
> 
> LINK_INBAND_BYPASS indicates that the hardware has the ability to
> bypass in-band signalling when enabled after a timeout if the link
> partner does not respond to its in-band signalling.
> 
> This reports the PHY capabilities for the particular interface mode,
> not the current configuration.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 05/16] net: phy: bcm84881: implement phy_inband_caps() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:41AM +0000, Russell King (Oracle) wrote:
> BCM84881 has no support for inband signalling, so this is a trivial
> implementation that returns no support for inband.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 06/16] net: phy: marvell: implement phy_inband_caps() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:46AM +0000, Russell King (Oracle) wrote:
> Provide an implementation for phy_inband_caps() for Marvell PHYs used
> on SFP modules, so that phylink knows the PHYs capabilities.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 07/16] net: phy: add phy_config_inband()

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:51AM +0000, Russell King (Oracle) wrote:
> Add a method to configure the PHY's in-band mode.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 08/16] net: phy: marvell: implement config_inband() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:24:56AM +0000, Russell King (Oracle) wrote:
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 09/16] net: phylink: add pcs_inband_caps() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:25:01AM +0000, Russell King (Oracle) wrote:
> Add a pcs_inband_caps() method to query the PCS for its inband link
> capabilities, and use this to determine whether link modes used with
> optical SFPs can be supported.
> 
> When a PCS does not provide a method, we allow inband negotiation to
> be either on or off, making this a no-op until the pcs_inband_caps()
> method is implemented by a PCS driver.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 10/16] net: mvneta: implement pcs_inband_caps() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:25:06AM +0000, Russell King (Oracle) wrote:
> Report the PCS in-band capabilities to phylink for Marvell NETA
> interfaces.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 11/16] net: mvpp2: implement pcs_inband_caps() method

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:25:11AM +0000, Russell King (Oracle) wrote:
> Report the PCS in-band capabilities to phylink for Marvell PP2
> interfaces.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 15/16] net: phylink: add negotiation of in-band capabilities

[Andrew Lunn]

> +		if (pcs_ib_caps && pcs_ib_caps != LINK_INBAND_DISABLE) {
> +			/* PCS supports reporting in-band capabilities, and
> +			 * supports more than disable mode.
> +			 */
> +			if (pcs_ib_caps & LINK_INBAND_DISABLE)
> +				neg_mode = PHYLINK_PCS_NEG_OUTBAND;
> +			else if (pcs_ib_caps & LINK_INBAND_ENABLE)
> +				pcs_ib_only = true;
> +		}
> +
> +		if (phy_ib_caps && phy_ib_caps != LINK_INBAND_DISABLE) {
> +			/* PHY supports in-band capabilities, and supports
> +			 * more than disable mode.
> +			 */
> +			if (phy_ib_caps & LINK_INBAND_DISABLE)
> +				pl->phy_ib_mode = LINK_INBAND_DISABLE;
> +			else if (phy_ib_caps & LINK_INBAND_BYPASS)
> +				pl->phy_ib_mode = LINK_INBAND_BYPASS;
> +			else if (phy_ib_caps & LINK_INBAND_ENABLE)
> +				phy_ib_only = true;

Looking at the different handling between PCS and PHY, i asked myself,
does PCS BYPASS exist? If it is invalid, i don't see a check if the
PCS is reporting it and should we be issuing a warning?

    Andrew

Re: [PATCH RFC net-next 16/16] net: phylink: remove phylink_phy_no_inband()

[Andrew Lunn]

On Tue, Nov 26, 2024 at 09:25:37AM +0000, Russell King (Oracle) wrote:
> Remove phylink_phy_no_inband() now that we are handling the lack of
> inband negotiation by querying the capabilities of the PHY and PCS,
> and the BCM84881 PHY driver provides us the information necessary to
> make the decision.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH RFC net-next 15/16] net: phylink: add negotiation of in-band capabilities

[Russell King (Oracle)]

On Tue, Nov 26, 2024 at 10:18:56PM +0100, Andrew Lunn wrote:
> > +		if (pcs_ib_caps && pcs_ib_caps != LINK_INBAND_DISABLE) {
> > +			/* PCS supports reporting in-band capabilities, and
> > +			 * supports more than disable mode.
> > +			 */
> > +			if (pcs_ib_caps & LINK_INBAND_DISABLE)
> > +				neg_mode = PHYLINK_PCS_NEG_OUTBAND;
> > +			else if (pcs_ib_caps & LINK_INBAND_ENABLE)
> > +				pcs_ib_only = true;
> > +		}
> > +
> > +		if (phy_ib_caps && phy_ib_caps != LINK_INBAND_DISABLE) {
> > +			/* PHY supports in-band capabilities, and supports
> > +			 * more than disable mode.
> > +			 */
> > +			if (phy_ib_caps & LINK_INBAND_DISABLE)
> > +				pl->phy_ib_mode = LINK_INBAND_DISABLE;
> > +			else if (phy_ib_caps & LINK_INBAND_BYPASS)
> > +				pl->phy_ib_mode = LINK_INBAND_BYPASS;
> > +			else if (phy_ib_caps & LINK_INBAND_ENABLE)
> > +				phy_ib_only = true;
> 
> Looking at the different handling between PCS and PHY, i asked myself,
> does PCS BYPASS exist? If it is invalid, i don't see a check if the
> PCS is reporting it and should we be issuing a warning?

Yes, it does exist - see for example MVNETA_GMAC_AN_BYPASS_ENABLE for
mvneta - but there's complications to using it that need sorting first.

The problem is if SGMII enters bypass mode, then the duplex is
configured according to MVNETA_GMAC_CONFIG_FULL_DUPLEX. In wonderful
Marvell style, it makes no mention about the speed setting. It does
say that it's supported for "SGMII modes". One assumes that it would
do the same thing and fall back to setting described by the two speed
bits, but the documentation doesn't say that. Maybe "SGMII modes" is
referring to Base-X only and not Cisco SGMII.

The problem of what seems to be almost an industry wide abuse of the
"SGMII" term creating a trainwreck strikes again!

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH RFC net-next 12/16] net: pcs: pcs-lynx: implement pcs_inband_caps() method

[Maxime Chevallier]

Hello Russell,

On Tue, 26 Nov 2024 09:25:16 +0000
"Russell King (Oracle)" <rmk+kernel@armlinux.org.uk> wrote:

> Report the PCS in-band capabilities to phylink for the Lynx PCS.

I'm a bit familiar with Lynx for Altera TSE, so my experience with it
is limited to 1000BaseX/SGMII. I unfortunately no longer have the
hardware to test it.

Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>

Thanks,

Maxime