[PATCH net-next v2 00/13] net: phy: Rework linkmodes handling in a dedicated file

[PATCH net-next v2 00/13] net: phy: Rework linkmodes handling in a dedicated file

[Maxime Chevallier]

Hello everyone,

This is the V2 of the phy_caps series. This series aims at reworking the way
we do conversions between speed/duplex, linkmodes and interfaces. There's two
goals here :
 - Make that conversion easier to maintain and somewhat more efficient, by
   avoiding the re-definitions of capabilities to linkmodes to interfaces that
   exist in phylib and phylink
 - create an internal API for these conversions, in preparation for the phy_port
   work.

This V2 reworks the way we deal with the phy_interface_t <-> caps <-> linkmodes,
leaving the MAC_*** capabilities a phylink-only set of values.

This V2 also addresses the comments from Köry as well as a kdoc warning.

V1 : https://lore.kernel.org/netdev/20250222142727.894124-1-maxime.chevallier@bootlin.com/

For context, The text below is an extract from the V1 cover :

Following the V4 of the phy_port series [1] we've discussed about attempting
to extract some of the linkmode <-> capabilities (speed/duplex) <-> interface
logic into a dedicated file, so that we can re-use that logic out of
phylink.

While trying to do that, I might have gotten a bit carried-away, and I'm
therefore submitting this series to rework the way we are currently
managing the linkmodes <-> capabilities handling.

We are currently defining all the possible Ethernet linkmodes in an
enum ethtool_link_mode_bit_indices value defined in uapi/linux/ethtool.h :

	ETHTOOL_LINK_MODE_10baseT_Half_BIT	= 0,
	ETHTOOL_LINK_MODE_10baseT_Full_BIT	= 1,
	...

Each of these modes represents a media-side link definition, and runs at
a given speed and duplex.

Specific attributes for each modes are stored in net/ethtool/common.c, as
an array of struct link_mode_info :

	struct link_mode_info {
		int				speed;
		u8				lanes;
		u8				duplex;
	}

The link_mode_params[] array is the canonical definition for these modes,
as (1) there are build-time checks to make sure any new linkmode
definition is also defined in this array and (2) this array is always
compiled-in, as it's part of the net stack (i.e. it is not phylib-specific).

This array is however not optimized for lookups, as it is not ordered in
any particular fashion (new modes go at the end, regardless of their speed
and duplex).

Phylib also includes a similar array, in the form of the phy_settings
array in drivers/net/phy/phy-core.c :

	struct phy_setting {
		u32 speed;
		u8 duplex;
		u8 bit; // The enum index for the linkmode
	};

The phy_settings array however is ordered by descending speeds. A variety
of helpers in phylib rely on that ordering to perform lookups, usually
to get one or any linkmode corresponding to a requested speed and duplex.

Finally, we have some helpers in phylink (phylink_caps_to_linkmodes) that
allows getting the list of linkmodes that match a set of speed and duplex
value, all at once.

While the phylink and phylib helpers allows for efficient lookups, they
have some drawbacks as well :

	(1) : It's easy to forget updating of all of these helpers and structures
		  when adding a new linkmode. New linkmodes are actually added fairly
		  often, lately either for slow BaseT1 flavours, or for crazy-fast
		  modes (800Gbps modes, but I guess people won't stop there)
		  
	(2) : Even though the phylink and phylib modes use carefull sorting
		  to speed-up the lookup process, the phylib lookups are usually
		  done in descending speed order and will therefore get slower
		  as people add even faster link speeds.
		  
This series introduces a new "link_capabilities" structure that is used
to build an array of link_caps :

	struct link_capabilities {
		int speed;                           
		unsigned int duplex;
		__ETHTOOL_DECLARE_LINK_MODE_MASK(linkmodes);
	};

We group these in an array, indexed with LINK_CAPA enums that are basically
identical to the phylink MAC_CAPS :

...
LINK_CAPA_1000HD,             
LINK_CAPA_1000FD,
LINK_CAPA_2500FD,
LINK_CAPA_5000FD,
...

We now have an associative array of <speed,duplex> <-> All compatible linkmodes

This array is initialized at phylib-init time based on the content of
the link_mode_params[] array from net/ethtool/common.c, that way it is
always up-to-date with new modes, and always properly ordered.

Patches 3 to 8 then convert all lookups from the phy_settings array into
lookups from this link_caps array, hopefully speeding-up lookups in the
meantime (we iterate over possible speeds instead of individual linkmodes)

This series is not meant to introduce changes in behaviour, however patches
9 and 10 do introduce functionnal changes. When configuring the advert
for speeds >= 1G in PHY devices, as well as when constructing the link
parameters for fixed links in phylink, we used to rely on phy_settings
lookups returning one, and only one, compatible linkmode. This series will
make so that the lookups will result on all matching linkmodes being
returned, and MAY cause advert/fixed-link configuring more linkmodes.

Patches 12 and 13 extract the conversion logic for interface <-> caps from
phylink.

There are cons as well for this, as this is a bit more init time for phylib,
but maybe more importantly, we lose in the precision for the lookups in
phy_settings. However, given all the uses for phy_settings (most are just
to get speed/duplex), I think this is actually ok, but any comment would
be very welcome.

This series was tested with :
 - 10/100/1000M links
 - 2,5, 5, 10G BaseT links
 - 1G Fixed link

I also made sure that this compiles with the following options :

CONFIG_PHYLIB=n

CNFIG_PHYLINK=m
CONFIG_PHYLIB=m

CNFIG_PHYLINK=m
CONFIG_PHYLIB=y

CNFIG_PHYLINK=y
CONFIG_PHYLIB=y

All the new helpers that were introduced (in drivers/net/phy/phy-caps.h)
are for internal use only (only users should be core stuff, such as phylib and
phylink, and in the future, phy_port).

Thanks,

Maxime

[1]: https://lore.kernel.org/netdev/20250213101606.1154014-1-maxime.chevallier@bootlin.com/



Maxime Chevallier (13):
  net: ethtool: Export the link_mode_params definitions
  net: phy: Use an internal, searchable storage for the linkmodes
  net: phy: phy_caps: Move phy_speeds to phy_caps
  net: phy: phy_caps: Move __set_linkmode_max_speed to phy_caps
  net: phy: phy_caps: Introduce phy_caps_valid
  net: phy: phy_caps: Implement link_capabilities lookup by linkmode
  net: phy: phy_caps: Allow looking-up link caps based on speed and
    duplex
  net: phy: phy_device: Use link_capabilities lookup for PHY aneg config
  net: phy: phylink: Use phy_caps_lookup for fixed-link configuration
  net: phy: drop phy_settings and the associated lookup helpers
  net: phy: phylink: Add a mapping between MAC_CAPS and LINK_CAPS
  net: phy: phylink: Convert capabilities to linkmodes using phy_caps
  net: phy: phy_caps: Allow getting an phy_interface's capabilities

 drivers/net/phy/Makefile     |   2 +-
 drivers/net/phy/phy-caps.h   |  62 +++++++
 drivers/net/phy/phy-core.c   | 253 ++------------------------
 drivers/net/phy/phy.c        |  37 ++--
 drivers/net/phy/phy_caps.c   | 340 +++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c |  13 +-
 drivers/net/phy/phylink.c    | 337 +++++++++-------------------------
 include/linux/ethtool.h      |   8 +
 include/linux/phy.h          |  15 --
 net/ethtool/common.c         |   1 +
 net/ethtool/common.h         |   7 -
 11 files changed, 532 insertions(+), 543 deletions(-)
 create mode 100644 drivers/net/phy/phy-caps.h
 create mode 100644 drivers/net/phy/phy_caps.c

-- 
2.48.1

[PATCH net-next v2 01/13] net: ethtool: Export the link_mode_params definitions

[Maxime Chevallier]

link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.

As a preparation for a port representation, export that table for the
rest of the net stack to use.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: Moved that patch at the beginning of the series

 include/linux/ethtool.h | 8 ++++++++
 net/ethtool/common.c    | 1 +
 net/ethtool/common.h    | 7 -------
 3 files changed, 9 insertions(+), 7 deletions(-)

diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 7f222dccc7d1..8210ece94fa6 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -210,6 +210,14 @@ static inline u8 *ethtool_rxfh_context_key(struct ethtool_rxfh_context *ctx)
 
 void ethtool_rxfh_context_lost(struct net_device *dev, u32 context_id);
 
+struct link_mode_info {
+	int                             speed;
+	u8                              lanes;
+	u8                              duplex;
+};
+
+extern const struct link_mode_info link_mode_params[];
+
 /* declare a link mode bitmap */
 #define __ETHTOOL_DECLARE_LINK_MODE_MASK(name)		\
 	DECLARE_BITMAP(name, __ETHTOOL_LINK_MODE_MASK_NBITS)
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index 7149d07e90c6..6b0178c09d72 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -422,6 +422,7 @@ const struct link_mode_info link_mode_params[] = {
 	__DEFINE_LINK_MODE_PARAMS(800000, VR4, Full),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);
+EXPORT_SYMBOL_GPL(link_mode_params);
 
 const char netif_msg_class_names[][ETH_GSTRING_LEN] = {
 	[NETIF_MSG_DRV_BIT]		= "drv",
diff --git a/net/ethtool/common.h b/net/ethtool/common.h
index 58e9e7db06f9..b9f99fb1d8e1 100644
--- a/net/ethtool/common.h
+++ b/net/ethtool/common.h
@@ -15,12 +15,6 @@
 #define __SOF_TIMESTAMPING_CNT (const_ilog2(SOF_TIMESTAMPING_LAST) + 1)
 #define __HWTSTAMP_FLAG_CNT (const_ilog2(HWTSTAMP_FLAG_LAST) + 1)
 
-struct link_mode_info {
-	int				speed;
-	u8				lanes;
-	u8				duplex;
-};
-
 struct genl_info;
 struct hwtstamp_provider_desc;
 
@@ -33,7 +27,6 @@ tunable_strings[__ETHTOOL_TUNABLE_COUNT][ETH_GSTRING_LEN];
 extern const char
 phy_tunable_strings[__ETHTOOL_PHY_TUNABLE_COUNT][ETH_GSTRING_LEN];
 extern const char link_mode_names[][ETH_GSTRING_LEN];
-extern const struct link_mode_info link_mode_params[];
 extern const char netif_msg_class_names[][ETH_GSTRING_LEN];
 extern const char wol_mode_names[][ETH_GSTRING_LEN];
 extern const char sof_timestamping_names[][ETH_GSTRING_LEN];
-- 
2.48.1

[PATCH net-next v2 02/13] net: phy: Use an internal, searchable storage for the linkmodes

[Maxime Chevallier]

The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.

Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.

However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.

We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.

We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.

That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - Moved the LINK_CAPA enums in phy-caps.h
	  - Fixed typos in the commit log reported by Köry
	  
 drivers/net/phy/Makefile     |  2 +-
 drivers/net/phy/phy-caps.h   | 44 ++++++++++++++++++++
 drivers/net/phy/phy_caps.c   | 78 ++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c |  2 +
 4 files changed, 125 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/phy/phy-caps.h
 create mode 100644 drivers/net/phy/phy_caps.c

diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index c8dac6e92278..7e800619162b 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -2,7 +2,7 @@
 # Makefile for Linux PHY drivers
 
 libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o \
-				   linkmode.o phy_link_topology.o
+				   linkmode.o phy_link_topology.o phy_caps.o
 mdio-bus-y			+= mdio_bus.o mdio_device.o
 
 ifdef CONFIG_MDIO_DEVICE
diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
new file mode 100644
index 000000000000..846d483269f6
--- /dev/null
+++ b/drivers/net/phy/phy-caps.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * link caps internal header, for link modes <-> capabilities <-> interfaces
+ * conversions.
+ */
+
+#ifndef __PHY_CAPS_H
+#define __PHY_CAPS_H
+
+#include <linux/ethtool.h>
+
+enum {
+	LINK_CAPA_10HD = 0,
+	LINK_CAPA_10FD,
+	LINK_CAPA_100HD,
+	LINK_CAPA_100FD,
+	LINK_CAPA_1000HD,
+	LINK_CAPA_1000FD,
+	LINK_CAPA_2500FD,
+	LINK_CAPA_5000FD,
+	LINK_CAPA_10000FD,
+	LINK_CAPA_20000FD,
+	LINK_CAPA_25000FD,
+	LINK_CAPA_40000FD,
+	LINK_CAPA_50000FD,
+	LINK_CAPA_56000FD,
+	LINK_CAPA_100000FD,
+	LINK_CAPA_200000FD,
+	LINK_CAPA_400000FD,
+	LINK_CAPA_800000FD,
+
+	__LINK_CAPA_LAST = LINK_CAPA_800000FD,
+	__LINK_CAPA_MAX,
+};
+
+struct link_capabilities {
+	int speed;
+	unsigned int duplex;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(linkmodes);
+};
+
+void phy_caps_init(void);
+
+#endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
new file mode 100644
index 000000000000..367ca7110ddc
--- /dev/null
+++ b/drivers/net/phy/phy_caps.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include <linux/ethtool.h>
+#include <linux/linkmode.h>
+#include <linux/phy.h>
+
+#include "phy-caps.h"
+
+static struct link_capabilities link_caps[__LINK_CAPA_MAX] __ro_after_init = {
+	{ SPEED_10, DUPLEX_HALF, {0} }, /* LINK_CAPA_10HD */
+	{ SPEED_10, DUPLEX_FULL, {0} }, /* LINK_CAPA_10FD */
+	{ SPEED_100, DUPLEX_HALF, {0} }, /* LINK_CAPA_100HD */
+	{ SPEED_100, DUPLEX_FULL, {0} }, /* LINK_CAPA_100FD */
+	{ SPEED_1000, DUPLEX_HALF, {0} }, /* LINK_CAPA_1000HD */
+	{ SPEED_1000, DUPLEX_FULL, {0} }, /* LINK_CAPA_1000FD */
+	{ SPEED_2500, DUPLEX_FULL, {0} }, /* LINK_CAPA_2500FD */
+	{ SPEED_5000, DUPLEX_FULL, {0} }, /* LINK_CAPA_5000FD */
+	{ SPEED_10000, DUPLEX_FULL, {0} }, /* LINK_CAPA_10000FD */
+	{ SPEED_20000, DUPLEX_FULL, {0} }, /* LINK_CAPA_20000FD */
+	{ SPEED_25000, DUPLEX_FULL, {0} }, /* LINK_CAPA_25000FD */
+	{ SPEED_40000, DUPLEX_FULL, {0} }, /* LINK_CAPA_40000FD */
+	{ SPEED_50000, DUPLEX_FULL, {0} }, /* LINK_CAPA_50000FD */
+	{ SPEED_56000, DUPLEX_FULL, {0} }, /* LINK_CAPA_56000FD */
+	{ SPEED_100000, DUPLEX_FULL, {0} }, /* LINK_CAPA_100000FD */
+	{ SPEED_200000, DUPLEX_FULL, {0} }, /* LINK_CAPA_200000FD */
+	{ SPEED_400000, DUPLEX_FULL, {0} }, /* LINK_CAPA_400000FD */
+	{ SPEED_800000, DUPLEX_FULL, {0} }, /* LINK_CAPA_800000FD */
+};
+
+static int speed_duplex_to_capa(int speed, unsigned int duplex)
+{
+	if (duplex == DUPLEX_UNKNOWN ||
+	    (speed > SPEED_1000 && duplex != DUPLEX_FULL))
+		return -EINVAL;
+
+	switch (speed) {
+	case SPEED_10: return duplex == DUPLEX_FULL ?
+			      LINK_CAPA_10FD : LINK_CAPA_10HD;
+	case SPEED_100: return duplex == DUPLEX_FULL ?
+			       LINK_CAPA_100FD : LINK_CAPA_100HD;
+	case SPEED_1000: return duplex == DUPLEX_FULL ?
+				LINK_CAPA_1000FD : LINK_CAPA_1000HD;
+	case SPEED_2500: return LINK_CAPA_2500FD;
+	case SPEED_5000: return LINK_CAPA_5000FD;
+	case SPEED_10000: return LINK_CAPA_10000FD;
+	case SPEED_20000: return LINK_CAPA_20000FD;
+	case SPEED_25000: return LINK_CAPA_25000FD;
+	case SPEED_40000: return LINK_CAPA_40000FD;
+	case SPEED_50000: return LINK_CAPA_50000FD;
+	case SPEED_56000: return LINK_CAPA_56000FD;
+	case SPEED_100000: return LINK_CAPA_100000FD;
+	case SPEED_200000: return LINK_CAPA_200000FD;
+	case SPEED_400000: return LINK_CAPA_400000FD;
+	case SPEED_800000: return LINK_CAPA_800000FD;
+	}
+
+	return -EINVAL;
+}
+
+/**
+ * phy_caps_init() - Initializes the link_caps array from the link_mode_params.
+ */
+void phy_caps_init(void)
+{
+	const struct link_mode_info *linkmode;
+	int i, capa;
+
+	/* Fill the caps array from net/ethtool/common.c */
+	for (i = 0; i < __ETHTOOL_LINK_MODE_MASK_NBITS; i++) {
+		linkmode = &link_mode_params[i];
+		capa = speed_duplex_to_capa(linkmode->speed, linkmode->duplex);
+
+		if (capa < 0)
+			continue;
+
+		__set_bit(i, link_caps[capa].linkmodes);
+	}
+}
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index a38d399f244b..9c573555ac49 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -42,6 +42,7 @@
 #include <linux/unistd.h>
 
 #include "phylib-internal.h"
+#include "phy-caps.h"
 
 MODULE_DESCRIPTION("PHY library");
 MODULE_AUTHOR("Andy Fleming");
@@ -3795,6 +3796,7 @@ static int __init phy_init(void)
 	if (rc)
 		goto err_ethtool_phy_ops;
 
+	phy_caps_init();
 	features_init();
 
 	rc = phy_driver_register(&genphy_c45_driver, THIS_MODULE);
-- 
2.48.1

[PATCH net-next v2 03/13] net: phy: phy_caps: Move phy_speeds to phy_caps

[Maxime Chevallier]

Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy-caps.h |  3 +++
 drivers/net/phy/phy-core.c | 15 ---------------
 drivers/net/phy/phy.c      |  3 ++-
 drivers/net/phy/phy_caps.c | 27 +++++++++++++++++++++++++++
 include/linux/phy.h        |  2 --
 5 files changed, 32 insertions(+), 18 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 846d483269f6..f8cdfdb09242 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -41,4 +41,7 @@ struct link_capabilities {
 
 void phy_caps_init(void);
 
+size_t phy_caps_speeds(unsigned int *speeds, size_t size,
+		       unsigned long *linkmodes);
+
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index b1c1670de23b..8533e57c3500 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -339,21 +339,6 @@ phy_lookup_setting(int speed, int duplex, const unsigned long *mask, bool exact)
 }
 EXPORT_SYMBOL_GPL(phy_lookup_setting);
 
-size_t phy_speeds(unsigned int *speeds, size_t size,
-		  unsigned long *mask)
-{
-	size_t count;
-	int i;
-
-	for (i = 0, count = 0; i < ARRAY_SIZE(settings) && count < size; i++)
-		if (settings[i].bit < __ETHTOOL_LINK_MODE_MASK_NBITS &&
-		    test_bit(settings[i].bit, mask) &&
-		    (count == 0 || speeds[count - 1] != settings[i].speed))
-			speeds[count++] = settings[i].speed;
-
-	return count;
-}
-
 static void __set_linkmode_max_speed(u32 max_speed, unsigned long *addr)
 {
 	const struct phy_setting *p;
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 16ffc00b419c..3128df03feda 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -37,6 +37,7 @@
 #include <net/sock.h>
 
 #include "phylib-internal.h"
+#include "phy-caps.h"
 
 #define PHY_STATE_TIME	HZ
 
@@ -245,7 +246,7 @@ unsigned int phy_supported_speeds(struct phy_device *phy,
 				  unsigned int *speeds,
 				  unsigned int size)
 {
-	return phy_speeds(speeds, size, phy->supported);
+	return phy_caps_speeds(speeds, size, phy->supported);
 }
 
 /**
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 367ca7110ddc..e5c716365b36 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -76,3 +76,30 @@ void phy_caps_init(void)
 		__set_bit(i, link_caps[capa].linkmodes);
 	}
 }
+
+/**
+ * phy_caps_speeds() - Fill an array of supported SPEED_* values for given modes
+ * @speeds: Output array to store the speeds list into
+ * @size: Size of the output array
+ * @linkmodes: Linkmodes to get the speeds from
+ *
+ * Fills the speeds array with all possible speeds that can be achieved with
+ * the specified linkmodes.
+ *
+ * Returns: The number of speeds filled into the array. If the input array isn't
+ *	    big enough to store all speeds, fill it as much as possible.
+ */
+size_t phy_caps_speeds(unsigned int *speeds, size_t size,
+		       unsigned long *linkmodes)
+{
+	size_t count;
+	int capa;
+
+	for (capa = 0, count = 0; capa < __LINK_CAPA_MAX && count < size; capa++) {
+		if (linkmode_intersects(link_caps[capa].linkmodes, linkmodes) &&
+		    (count == 0 || speeds[count - 1] != link_caps[capa].speed))
+			speeds[count++] = link_caps[capa].speed;
+	}
+
+	return count;
+}
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 7bfbae51070a..5749aad96862 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1322,8 +1322,6 @@ struct phy_setting {
 const struct phy_setting *
 phy_lookup_setting(int speed, int duplex, const unsigned long *mask,
 		   bool exact);
-size_t phy_speeds(unsigned int *speeds, size_t size,
-		  unsigned long *mask);
 
 /**
  * phy_is_started - Convenience function to check whether PHY is started
-- 
2.48.1

[PATCH net-next v2 04/13] net: phy: phy_caps: Move __set_linkmode_max_speed to phy_caps

[Maxime Chevallier]

Convert the __set_linkmode_max_speed to use the link_capabilities array.
This makes it easy to clamp the linkmodes to a given max speed.
Introduce a new helper phy_caps_linkmode_max_speed to replace the
previous one that used phy_settings.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy-caps.h |  2 ++
 drivers/net/phy/phy-core.c | 18 +++---------------
 drivers/net/phy/phy_caps.c | 16 ++++++++++++++++
 3 files changed, 21 insertions(+), 15 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index f8cdfdb09242..3f011b63a417 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -43,5 +43,7 @@ void phy_caps_init(void);
 
 size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 		       unsigned long *linkmodes);
+void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes);
+
 
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index 8533e57c3500..f62bc1be67b2 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -7,6 +7,7 @@
 #include <linux/of.h>
 
 #include "phylib-internal.h"
+#include "phy-caps.h"
 
 /**
  * phy_speed_to_str - Return a string representing the PHY link speed
@@ -339,22 +340,9 @@ phy_lookup_setting(int speed, int duplex, const unsigned long *mask, bool exact)
 }
 EXPORT_SYMBOL_GPL(phy_lookup_setting);
 
-static void __set_linkmode_max_speed(u32 max_speed, unsigned long *addr)
-{
-	const struct phy_setting *p;
-	int i;
-
-	for (i = 0, p = settings; i < ARRAY_SIZE(settings); i++, p++) {
-		if (p->speed > max_speed)
-			linkmode_clear_bit(p->bit, addr);
-		else
-			break;
-	}
-}
-
 static void __set_phy_supported(struct phy_device *phydev, u32 max_speed)
 {
-	__set_linkmode_max_speed(max_speed, phydev->supported);
+	phy_caps_linkmode_max_speed(max_speed, phydev->supported);
 }
 
 /**
@@ -557,7 +545,7 @@ int phy_speed_down_core(struct phy_device *phydev)
 	if (min_common_speed == SPEED_UNKNOWN)
 		return -EINVAL;
 
-	__set_linkmode_max_speed(min_common_speed, phydev->advertising);
+	phy_caps_linkmode_max_speed(min_common_speed, phydev->advertising);
 
 	return 0;
 }
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index e5c716365b36..9075f9840ebd 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -103,3 +103,19 @@ size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 
 	return count;
 }
+
+/**
+ * phy_caps_linkmode_max_speed() - Clamp a linkmodes set to a max speed
+ * @max_speed: Speed limit for the linkmode set
+ * @linkmodes: Linkmodes to limit
+ */
+void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes)
+{
+	int capa;
+
+	for (capa = __LINK_CAPA_LAST; capa >= 0; capa--)
+		if (link_caps[capa].speed > max_speed)
+			linkmode_andnot(linkmodes, linkmodes, link_caps[capa].linkmodes);
+		else
+			break;
+}
-- 
2.48.1

[PATCH net-next v2 05/13] net: phy: phy_caps: Introduce phy_caps_valid

[Maxime Chevallier]

With the link_capabilities array, it's trivial to validate a given mask
againts a <speed, duplex> tuple. Create a helper for that purpose, and
use it to replace a phy_settings lookup in phy_check_valid();

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - Renamed the commit and added missing kdoc

 drivers/net/phy/phy-caps.h |  1 +
 drivers/net/phy/phy.c      |  2 +-
 drivers/net/phy/phy_caps.c | 19 +++++++++++++++++++
 3 files changed, 21 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 3f011b63a417..7359983fce0f 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -44,6 +44,7 @@ void phy_caps_init(void);
 size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 		       unsigned long *linkmodes);
 void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes);
+bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes);
 
 
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 3128df03feda..8df37d221fba 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -260,7 +260,7 @@ unsigned int phy_supported_speeds(struct phy_device *phy,
  */
 bool phy_check_valid(int speed, int duplex, unsigned long *features)
 {
-	return !!phy_lookup_setting(speed, duplex, features, true);
+	return phy_caps_valid(speed, duplex, features);
 }
 EXPORT_SYMBOL(phy_check_valid);
 
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 9075f9840ebd..b776375ea9e4 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -119,3 +119,22 @@ void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes)
 		else
 			break;
 }
+
+/**
+ * phy_caps_valid() - Validate a linkmodes set agains given speed and duplex
+ * @speed: input speed to validate
+ * @duplex: input duplex to validate. Passing DUPLEX_UNKNOWN is always not valid
+ * @linkmodes: The linkmodes to validate
+ *
+ * Returns: True if at least one of the linkmodes in @linkmodes can function at
+ *          the given speed and duplex, false otherwise.
+ */
+bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes)
+{
+	int capa = speed_duplex_to_capa(speed, duplex);
+
+	if (capa < 0)
+		return false;
+
+	return linkmode_intersects(link_caps[capa].linkmodes, linkmodes);
+}
-- 
2.48.1

[PATCH net-next v2 06/13] net: phy: phy_caps: Implement link_capabilities lookup by linkmode

[Maxime Chevallier]

In several occasions, phylib needs to lookup a set of matching speed and
duplex against a given linkmode set. Instead of relying on the
phy_settings array and thus iterate over the whole linkmodes list, use
the link_capabilities array to lookup these matches, as we aren't
interested in the actual link setting that matches but rather the speed
and duplex for that setting.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy-caps.h |  5 +++++
 drivers/net/phy/phy-core.c | 36 +++++++++++++-----------------
 drivers/net/phy/phy_caps.c | 45 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 65 insertions(+), 21 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 7359983fce0f..7b95a9cb5ebb 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -46,5 +46,10 @@ size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes);
 bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes);
 
+const struct link_capabilities *
+phy_caps_lookup_by_linkmode(const unsigned long *linkmodes);
+
+const struct link_capabilities *
+phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only);
 
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index f62bc1be67b2..6cb8f857a7f1 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -468,16 +468,15 @@ EXPORT_SYMBOL_GPL(phy_resolve_aneg_pause);
 void phy_resolve_aneg_linkmode(struct phy_device *phydev)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(common);
-	int i;
+	const struct link_capabilities *c;
 
 	linkmode_and(common, phydev->lp_advertising, phydev->advertising);
 
-	for (i = 0; i < ARRAY_SIZE(settings); i++)
-		if (test_bit(settings[i].bit, common)) {
-			phydev->speed = settings[i].speed;
-			phydev->duplex = settings[i].duplex;
-			break;
-		}
+	c = phy_caps_lookup_by_linkmode(common);
+	if (c) {
+		phydev->speed = c->speed;
+		phydev->duplex = c->duplex;
+	}
 
 	phy_resolve_aneg_pause(phydev);
 }
@@ -495,7 +494,8 @@ EXPORT_SYMBOL_GPL(phy_resolve_aneg_linkmode);
 void phy_check_downshift(struct phy_device *phydev)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(common);
-	int i, speed = SPEED_UNKNOWN;
+	const struct link_capabilities *c;
+	int speed = SPEED_UNKNOWN;
 
 	phydev->downshifted_rate = 0;
 
@@ -505,11 +505,9 @@ void phy_check_downshift(struct phy_device *phydev)
 
 	linkmode_and(common, phydev->lp_advertising, phydev->advertising);
 
-	for (i = 0; i < ARRAY_SIZE(settings); i++)
-		if (test_bit(settings[i].bit, common)) {
-			speed = settings[i].speed;
-			break;
-		}
+	c = phy_caps_lookup_by_linkmode(common);
+	if (c)
+		speed = c->speed;
 
 	if (speed == SPEED_UNKNOWN || phydev->speed >= speed)
 		return;
@@ -523,17 +521,13 @@ void phy_check_downshift(struct phy_device *phydev)
 static int phy_resolve_min_speed(struct phy_device *phydev, bool fdx_only)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(common);
-	int i = ARRAY_SIZE(settings);
+	const struct link_capabilities *c;
 
 	linkmode_and(common, phydev->lp_advertising, phydev->advertising);
 
-	while (--i >= 0) {
-		if (test_bit(settings[i].bit, common)) {
-			if (fdx_only && settings[i].duplex != DUPLEX_FULL)
-				continue;
-			return settings[i].speed;
-		}
-	}
+	c = phy_caps_lookup_by_linkmode_rev(common, fdx_only);
+	if (c)
+		return c->speed;
 
 	return SPEED_UNKNOWN;
 }
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index b776375ea9e4..8cf7ff3f1368 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -104,6 +104,51 @@ size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 	return count;
 }
 
+/**
+ * phy_caps_lookup_by_linkmode() - Lookup the fastest matching link_capabilities
+ * @linkmodes: Linkmodes to match against
+ *
+ * Returns: The highest-speed link_capabilities that intersects the given
+ *	    linkmodes. In case several DUPLEX_ options exist at that speed,
+ *	    DUPLEX_FULL is matched first. NULL is returned if no match.
+ */
+const struct link_capabilities *
+phy_caps_lookup_by_linkmode(const unsigned long *linkmodes)
+{
+	int capa;
+
+	for (capa = __LINK_CAPA_LAST; capa >= 0; capa--)
+		if (linkmode_intersects(link_caps[capa].linkmodes, linkmodes))
+			return &link_caps[capa];
+
+	return NULL;
+}
+
+/**
+ * phy_caps_lookup_by_linkmode_rev() - Lookup the slowest matching link_capabilities
+ * @linkmodes: Linkmodes to match against
+ * @fdx_only: Full duplex match only when set
+ *
+ * Returns: The lowest-speed link_capabilities that intersects the given
+ *	    linkmodes. When set, fdx_only will ignore half-duplex matches.
+ *	    NULL is returned if no match.
+ */
+const struct link_capabilities *
+phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only)
+{
+	int capa;
+
+	for (capa = 0; capa < __LINK_CAPA_MAX; capa++) {
+		if (fdx_only && link_caps[capa].duplex != DUPLEX_FULL)
+			continue;
+
+		if (linkmode_intersects(link_caps[capa].linkmodes, linkmodes))
+			return &link_caps[capa];
+	}
+
+	return NULL;
+}
+
 /**
  * phy_caps_linkmode_max_speed() - Clamp a linkmodes set to a max speed
  * @max_speed: Speed limit for the linkmode set
-- 
2.48.1

[PATCH net-next v2 07/13] net: phy: phy_caps: Allow looking-up link caps based on speed and duplex

[Maxime Chevallier]

As the link_caps array is efficient for <speed,duplex> lookups,
implement a function for speed/duplex lookups that matches a given
mask. This replicates to some extent the phy_lookup_settings()
behaviour, matching full link_capabilities instead of a single linkmode.

phy.c's phy_santize_settings() and phylink's
phylink_ethtool_ksettings_set() performs such lookup using the
phy_settings table, but are only interested in the actual speed/duplex
that were matched, rathet than the individual linkmode.

Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup()
will run through the link_caps[] array by descending speed/duplex order.

If the link_capabilities for a given <speed/duplex> tuple intersects the
passed linkmodes, we consider that a match.

Similar to phy_lookup_settings(), we also allow passing an 'exact'
boolean, allowing non-exact match. Here, we MUST always match the
linkmodes mask, but we allow matching on lower speed settings.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy-caps.h |  4 ++++
 drivers/net/phy/phy.c      | 32 ++++++-------------------
 drivers/net/phy/phy_caps.c | 49 ++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phylink.c  | 17 ++++++-------
 4 files changed, 69 insertions(+), 33 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 7b95a9cb5ebb..dd3ea9f77f1c 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -52,4 +52,8 @@ phy_caps_lookup_by_linkmode(const unsigned long *linkmodes);
 const struct link_capabilities *
 phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only);
 
+const struct link_capabilities *
+phy_caps_lookup(int speed, unsigned int duplex, const unsigned long *supported,
+		bool exact);
+
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 8df37d221fba..562acde89224 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -213,25 +213,6 @@ int phy_aneg_done(struct phy_device *phydev)
 }
 EXPORT_SYMBOL(phy_aneg_done);
 
-/**
- * phy_find_valid - find a PHY setting that matches the requested parameters
- * @speed: desired speed
- * @duplex: desired duplex
- * @supported: mask of supported link modes
- *
- * Locate a supported phy setting that is, in priority order:
- * - an exact match for the specified speed and duplex mode
- * - a match for the specified speed, or slower speed
- * - the slowest supported speed
- * Returns the matched phy_setting entry, or %NULL if no supported phy
- * settings were found.
- */
-static const struct phy_setting *
-phy_find_valid(int speed, int duplex, unsigned long *supported)
-{
-	return phy_lookup_setting(speed, duplex, supported, false);
-}
-
 /**
  * phy_supported_speeds - return all speeds currently supported by a phy device
  * @phy: The phy device to return supported speeds of.
@@ -274,13 +255,14 @@ EXPORT_SYMBOL(phy_check_valid);
  */
 static void phy_sanitize_settings(struct phy_device *phydev)
 {
-	const struct phy_setting *setting;
+	const struct link_capabilities *c;
+
+	c = phy_caps_lookup(phydev->speed, phydev->duplex, phydev->supported,
+			    false);
 
-	setting = phy_find_valid(phydev->speed, phydev->duplex,
-				 phydev->supported);
-	if (setting) {
-		phydev->speed = setting->speed;
-		phydev->duplex = setting->duplex;
+	if (c) {
+		phydev->speed = c->speed;
+		phydev->duplex = c->duplex;
 	} else {
 		/* We failed to find anything (no supported speeds?) */
 		phydev->speed = SPEED_UNKNOWN;
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 8cf7ff3f1368..77bf85043e82 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -149,6 +149,55 @@ phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only)
 	return NULL;
 }
 
+/**
+ * phy_caps_lookup() - Lookup capabilities by speed/duplex that matches a mask
+ * @speed: Speed to match
+ * @duplex: Duplex to match
+ * @supported: Mask of linkmodes to match
+ * @exact: Perform an exact match or not.
+ *
+ * Lookup a link_capabilities entry that intersect the supported linkmodes mask,
+ * and that matches the passed speed and duplex.
+ *
+ * When @exact is set, an exact match is performed on speed and duplex, meaning
+ * that if the linkmodes for the given speed and duplex intersect the supported
+ * mask, this capability is returned, otherwise we don't have a match and return
+ * NULL.
+ *
+ * When @exact is not set, we return either an exact match, or matching capabilities
+ * at lower speed, or the lowest matching speed, or NULL.
+ *
+ * Returns: a matched link_capabilities according to the above process, NULL
+ *	    otherwise.
+ */
+const struct link_capabilities *
+phy_caps_lookup(int speed, unsigned int duplex, const unsigned long *supported,
+		bool exact)
+{
+	const struct link_capabilities *c, *last = NULL;
+	int capa;
+
+	for (capa = __LINK_CAPA_LAST; capa >= 0; capa--) {
+		c = &link_caps[capa];
+		if (linkmode_intersects(c->linkmodes, supported)) {
+			last = c;
+			/* exact match on speed and duplex*/
+			if (c->speed == speed && c->duplex == duplex) {
+				return c;
+			} else if (!exact) {
+				if (c->speed <= speed)
+					return c;
+			}
+		}
+	}
+
+	if (!exact)
+		return last;
+
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(phy_caps_lookup);
+
 /**
  * phy_caps_linkmode_max_speed() - Clamp a linkmodes set to a max speed
  * @max_speed: Speed limit for the linkmode set
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index a3b186ab3854..6c67d5c9b787 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -20,6 +20,7 @@
 #include <linux/timer.h>
 #include <linux/workqueue.h>
 
+#include "phy-caps.h"
 #include "sfp.h"
 #include "swphy.h"
 
@@ -2852,8 +2853,8 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 				  const struct ethtool_link_ksettings *kset)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(support);
+	const struct link_capabilities *c;
 	struct phylink_link_state config;
-	const struct phy_setting *s;
 
 	ASSERT_RTNL();
 
@@ -2896,23 +2897,23 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 		/* Autonegotiation disabled, select a suitable speed and
 		 * duplex.
 		 */
-		s = phy_lookup_setting(kset->base.speed, kset->base.duplex,
-				       pl->supported, false);
-		if (!s)
+		c = phy_caps_lookup(kset->base.speed, kset->base.duplex,
+				    pl->supported, false);
+		if (!c)
 			return -EINVAL;
 
 		/* If we have a fixed link, refuse to change link parameters.
 		 * If the link parameters match, accept them but do nothing.
 		 */
 		if (pl->req_link_an_mode == MLO_AN_FIXED) {
-			if (s->speed != pl->link_config.speed ||
-			    s->duplex != pl->link_config.duplex)
+			if (c->speed != pl->link_config.speed ||
+			    c->duplex != pl->link_config.duplex)
 				return -EINVAL;
 			return 0;
 		}
 
-		config.speed = s->speed;
-		config.duplex = s->duplex;
+		config.speed = c->speed;
+		config.duplex = c->duplex;
 		break;
 
 	case AUTONEG_ENABLE:
-- 
2.48.1

[PATCH net-next v2 08/13] net: phy: phy_device: Use link_capabilities lookup for PHY aneg config

[Maxime Chevallier]

When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.

Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy_device.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 9c573555ac49..57b90ec6477e 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -2357,7 +2357,7 @@ EXPORT_SYMBOL(genphy_check_and_restart_aneg);
 int __genphy_config_aneg(struct phy_device *phydev, bool changed)
 {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(fixed_advert);
-	const struct phy_setting *set;
+	const struct link_capabilities *c;
 	unsigned long *advert;
 	int err;
 
@@ -2383,10 +2383,11 @@ int __genphy_config_aneg(struct phy_device *phydev, bool changed)
 	} else {
 		linkmode_zero(fixed_advert);
 
-		set = phy_lookup_setting(phydev->speed, phydev->duplex,
-					 phydev->supported, true);
-		if (set)
-			linkmode_set_bit(set->bit, fixed_advert);
+		c = phy_caps_lookup(phydev->speed, phydev->duplex,
+				    phydev->supported, true);
+		if (c)
+			linkmode_and(fixed_advert, phydev->supported,
+				     c->linkmodes);
 
 		advert = fixed_advert;
 	}
-- 
2.48.1

[PATCH net-next v2 09/13] net: phy: phylink: Use phy_caps_lookup for fixed-link configuration

[Maxime Chevallier]

When phylink creates a fixed-link configuration, it finds a matching
linkmode to set as the advertised, lp_advertising and supported modes
based on the speed and duplex of the fixed link.

Use the newly introduced phy_caps_lookup to get these modes instead of
phy_lookup_settings(). This has the side effect that the matched
settings and configured linkmodes may now contain several linkmodes (the
intersection of supported linkmodes from the phylink settings and the
linkmodes that match speed/duplex) instead of the one from
phy_lookup_settings().

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - fixed pl->link_config.lp_advertising setting

 drivers/net/phy/phylink.c | 26 +++++++++++++++-----------
 1 file changed, 15 insertions(+), 11 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 6c67d5c9b787..63fbf3d8708a 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -805,9 +805,10 @@ static int phylink_validate(struct phylink *pl, unsigned long *supported,
 static int phylink_parse_fixedlink(struct phylink *pl,
 				   const struct fwnode_handle *fwnode)
 {
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(match) = { 0, };
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+	const struct link_capabilities *c;
 	struct fwnode_handle *fixed_node;
-	const struct phy_setting *s;
 	struct gpio_desc *desc;
 	u32 speed;
 	int ret;
@@ -879,8 +880,10 @@ static int phylink_parse_fixedlink(struct phylink *pl,
 	linkmode_copy(pl->link_config.advertising, pl->supported);
 	phylink_validate(pl, pl->supported, &pl->link_config);
 
-	s = phy_lookup_setting(pl->link_config.speed, pl->link_config.duplex,
-			       pl->supported, true);
+	c = phy_caps_lookup(pl->link_config.speed, pl->link_config.duplex,
+			    pl->supported, true);
+	if (c)
+		linkmode_and(match, pl->supported, c->linkmodes);
 
 	linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT, mask);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, mask);
@@ -889,9 +892,10 @@ static int phylink_parse_fixedlink(struct phylink *pl,
 
 	phylink_set(pl->supported, MII);
 
-	if (s) {
-		__set_bit(s->bit, pl->supported);
-		__set_bit(s->bit, pl->link_config.lp_advertising);
+	if (c) {
+		linkmode_or(pl->supported, pl->supported, match);
+		linkmode_or(pl->link_config.lp_advertising,
+			    pl->link_config.lp_advertising, match);
 	} else {
 		phylink_warn(pl, "fixed link %s duplex %dMbps not recognised\n",
 			     pl->link_config.duplex == DUPLEX_FULL ? "full" : "half",
@@ -1879,21 +1883,21 @@ static int phylink_register_sfp(struct phylink *pl,
 int phylink_set_fixed_link(struct phylink *pl,
 			   const struct phylink_link_state *state)
 {
-	const struct phy_setting *s;
+	const struct link_capabilities *c;
 	unsigned long *adv;
 
 	if (pl->cfg_link_an_mode != MLO_AN_PHY || !state ||
 	    !test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state))
 		return -EINVAL;
 
-	s = phy_lookup_setting(state->speed, state->duplex,
-			       pl->supported, true);
-	if (!s)
+	c = phy_caps_lookup(state->speed, state->duplex,
+			    pl->supported, true);
+	if (!c)
 		return -EINVAL;
 
 	adv = pl->link_config.advertising;
 	linkmode_zero(adv);
-	linkmode_set_bit(s->bit, adv);
+	linkmode_and(adv, pl->supported, c->linkmodes);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, adv);
 
 	pl->link_config.speed = state->speed;
-- 
2.48.1

[PATCH net-next v2 10/13] net: phy: drop phy_settings and the associated lookup helpers

[Maxime Chevallier]

The phy_settings array is no longer relevant as it has now been replaced
by the link_caps array and associated phy_caps helpers.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - No changes

 drivers/net/phy/phy-core.c | 184 -------------------------------------
 include/linux/phy.h        |  13 ---
 2 files changed, 197 deletions(-)

diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index 6cb8f857a7f1..e7d0137abd48 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -156,190 +156,6 @@ int phy_interface_num_ports(phy_interface_t interface)
 }
 EXPORT_SYMBOL_GPL(phy_interface_num_ports);
 
-/* A mapping of all SUPPORTED settings to speed/duplex.  This table
- * must be grouped by speed and sorted in descending match priority
- * - iow, descending speed.
- */
-
-#define PHY_SETTING(s, d, b) { .speed = SPEED_ ## s, .duplex = DUPLEX_ ## d, \
-			       .bit = ETHTOOL_LINK_MODE_ ## b ## _BIT}
-
-static const struct phy_setting settings[] = {
-	/* 800G */
-	PHY_SETTING( 800000, FULL, 800000baseCR8_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseKR8_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseDR8_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseDR8_2_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseSR8_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseVR8_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseCR4_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseKR4_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseDR4_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseDR4_2_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseSR4_Full		),
-	PHY_SETTING( 800000, FULL, 800000baseVR4_Full		),
-	/* 400G */
-	PHY_SETTING( 400000, FULL, 400000baseCR8_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseKR8_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseLR8_ER8_FR8_Full	),
-	PHY_SETTING( 400000, FULL, 400000baseDR8_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseSR8_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseCR4_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseKR4_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseLR4_ER4_FR4_Full	),
-	PHY_SETTING( 400000, FULL, 400000baseDR4_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseSR4_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseCR2_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseKR2_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseDR2_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseDR2_2_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseSR2_Full		),
-	PHY_SETTING( 400000, FULL, 400000baseVR2_Full		),
-	/* 200G */
-	PHY_SETTING( 200000, FULL, 200000baseCR4_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseKR4_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseLR4_ER4_FR4_Full	),
-	PHY_SETTING( 200000, FULL, 200000baseDR4_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseSR4_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseCR2_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseKR2_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseLR2_ER2_FR2_Full	),
-	PHY_SETTING( 200000, FULL, 200000baseDR2_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseSR2_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseCR_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseKR_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseDR_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseDR_2_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseSR_Full		),
-	PHY_SETTING( 200000, FULL, 200000baseVR_Full		),
-	/* 100G */
-	PHY_SETTING( 100000, FULL, 100000baseCR4_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseKR4_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseLR4_ER4_Full	),
-	PHY_SETTING( 100000, FULL, 100000baseSR4_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseCR2_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseKR2_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseLR2_ER2_FR2_Full	),
-	PHY_SETTING( 100000, FULL, 100000baseDR2_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseSR2_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseCR_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseKR_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseLR_ER_FR_Full	),
-	PHY_SETTING( 100000, FULL, 100000baseDR_Full		),
-	PHY_SETTING( 100000, FULL, 100000baseSR_Full		),
-	/* 56G */
-	PHY_SETTING(  56000, FULL,  56000baseCR4_Full	  	),
-	PHY_SETTING(  56000, FULL,  56000baseKR4_Full	  	),
-	PHY_SETTING(  56000, FULL,  56000baseLR4_Full	  	),
-	PHY_SETTING(  56000, FULL,  56000baseSR4_Full	  	),
-	/* 50G */
-	PHY_SETTING(  50000, FULL,  50000baseCR2_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseKR2_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseSR2_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseCR_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseKR_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseLR_ER_FR_Full	),
-	PHY_SETTING(  50000, FULL,  50000baseDR_Full		),
-	PHY_SETTING(  50000, FULL,  50000baseSR_Full		),
-	/* 40G */
-	PHY_SETTING(  40000, FULL,  40000baseCR4_Full		),
-	PHY_SETTING(  40000, FULL,  40000baseKR4_Full		),
-	PHY_SETTING(  40000, FULL,  40000baseLR4_Full		),
-	PHY_SETTING(  40000, FULL,  40000baseSR4_Full		),
-	/* 25G */
-	PHY_SETTING(  25000, FULL,  25000baseCR_Full		),
-	PHY_SETTING(  25000, FULL,  25000baseKR_Full		),
-	PHY_SETTING(  25000, FULL,  25000baseSR_Full		),
-	/* 20G */
-	PHY_SETTING(  20000, FULL,  20000baseKR2_Full		),
-	PHY_SETTING(  20000, FULL,  20000baseMLD2_Full		),
-	/* 10G */
-	PHY_SETTING(  10000, FULL,  10000baseCR_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseER_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseKR_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseKX4_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseLR_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseLRM_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseR_FEC		),
-	PHY_SETTING(  10000, FULL,  10000baseSR_Full		),
-	PHY_SETTING(  10000, FULL,  10000baseT_Full		),
-	/* 5G */
-	PHY_SETTING(   5000, FULL,   5000baseT_Full		),
-	/* 2.5G */
-	PHY_SETTING(   2500, FULL,   2500baseT_Full		),
-	PHY_SETTING(   2500, FULL,   2500baseX_Full		),
-	/* 1G */
-	PHY_SETTING(   1000, FULL,   1000baseT_Full		),
-	PHY_SETTING(   1000, HALF,   1000baseT_Half		),
-	PHY_SETTING(   1000, FULL,   1000baseT1_Full		),
-	PHY_SETTING(   1000, FULL,   1000baseX_Full		),
-	PHY_SETTING(   1000, FULL,   1000baseKX_Full		),
-	/* 100M */
-	PHY_SETTING(    100, FULL,    100baseT_Full		),
-	PHY_SETTING(    100, FULL,    100baseT1_Full		),
-	PHY_SETTING(    100, HALF,    100baseT_Half		),
-	PHY_SETTING(    100, HALF,    100baseFX_Half		),
-	PHY_SETTING(    100, FULL,    100baseFX_Full		),
-	/* 10M */
-	PHY_SETTING(     10, FULL,     10baseT_Full		),
-	PHY_SETTING(     10, HALF,     10baseT_Half		),
-	PHY_SETTING(     10, FULL,     10baseT1L_Full		),
-	PHY_SETTING(     10, FULL,     10baseT1S_Full		),
-	PHY_SETTING(     10, HALF,     10baseT1S_Half		),
-	PHY_SETTING(     10, HALF,     10baseT1S_P2MP_Half	),
-	PHY_SETTING(     10, FULL,     10baseT1BRR_Full		),
-};
-#undef PHY_SETTING
-
-/**
- * phy_lookup_setting - lookup a PHY setting
- * @speed: speed to match
- * @duplex: duplex to match
- * @mask: allowed link modes
- * @exact: an exact match is required
- *
- * Search the settings array for a setting that matches the speed and
- * duplex, and which is supported.
- *
- * If @exact is unset, either an exact match or %NULL for no match will
- * be returned.
- *
- * If @exact is set, an exact match, the fastest supported setting at
- * or below the specified speed, the slowest supported setting, or if
- * they all fail, %NULL will be returned.
- */
-const struct phy_setting *
-phy_lookup_setting(int speed, int duplex, const unsigned long *mask, bool exact)
-{
-	const struct phy_setting *p, *match = NULL, *last = NULL;
-	int i;
-
-	for (i = 0, p = settings; i < ARRAY_SIZE(settings); i++, p++) {
-		if (p->bit < __ETHTOOL_LINK_MODE_MASK_NBITS &&
-		    test_bit(p->bit, mask)) {
-			last = p;
-			if (p->speed == speed && p->duplex == duplex) {
-				/* Exact match for speed and duplex */
-				match = p;
-				break;
-			} else if (!exact) {
-				if (!match && p->speed <= speed)
-					/* Candidate */
-					match = p;
-
-				if (p->speed < speed)
-					break;
-			}
-		}
-	}
-
-	if (!match && !exact)
-		match = last;
-
-	return match;
-}
-EXPORT_SYMBOL_GPL(phy_lookup_setting);
-
 static void __set_phy_supported(struct phy_device *phydev, u32 max_speed)
 {
 	phy_caps_linkmode_max_speed(max_speed, phydev->supported);
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 5749aad96862..4a59aa7254f4 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1310,19 +1310,6 @@ const char *phy_rate_matching_to_str(int rate_matching);
 
 int phy_interface_num_ports(phy_interface_t interface);
 
-/* A structure for mapping a particular speed and duplex
- * combination to a particular SUPPORTED and ADVERTISED value
- */
-struct phy_setting {
-	u32 speed;
-	u8 duplex;
-	u8 bit;
-};
-
-const struct phy_setting *
-phy_lookup_setting(int speed, int duplex, const unsigned long *mask,
-		   bool exact);
-
 /**
  * phy_is_started - Convenience function to check whether PHY is started
  * @phydev: The phy_device struct
-- 
2.48.1

[PATCH net-next v2 11/13] net: phy: phylink: Add a mapping between MAC_CAPS and LINK_CAPS

[Maxime Chevallier]

phylink allows MAC drivers to report the capabilities in terms of speed,
duplex and pause support. This is done through a dedicated set of enum
values in the form of the MAC_ capabilities. They are very close to what
the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
have any information about Pause/Asym Pause support.

To prepare converting phylink to using the phy_caps, add the mapping
between MAC capabilities and phy_caps. While doing so, we move the
phylink_caps_params array up a bit to simplify future commits.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - New patch

 drivers/net/phy/phylink.c | 49 ++++++++++++++++++++-------------------
 1 file changed, 25 insertions(+), 24 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 63fbf3d8708a..aaf07094b821 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -292,6 +292,31 @@ static int phylink_interface_max_speed(phy_interface_t interface)
 	return SPEED_UNKNOWN;
 }
 
+static struct {
+	unsigned long mask;
+	int speed;
+	unsigned int duplex;
+	unsigned int caps_bit;
+} phylink_caps_params[] = {
+	{ MAC_400000FD, SPEED_400000, DUPLEX_FULL, BIT(LINK_CAPA_400000FD) },
+	{ MAC_200000FD, SPEED_200000, DUPLEX_FULL, BIT(LINK_CAPA_200000FD) },
+	{ MAC_100000FD, SPEED_100000, DUPLEX_FULL, BIT(LINK_CAPA_100000FD) },
+	{ MAC_56000FD,  SPEED_56000,  DUPLEX_FULL, BIT(LINK_CAPA_56000FD) },
+	{ MAC_50000FD,  SPEED_50000,  DUPLEX_FULL, BIT(LINK_CAPA_50000FD) },
+	{ MAC_40000FD,  SPEED_40000,  DUPLEX_FULL, BIT(LINK_CAPA_40000FD) },
+	{ MAC_25000FD,  SPEED_25000,  DUPLEX_FULL, BIT(LINK_CAPA_25000FD) },
+	{ MAC_20000FD,  SPEED_20000,  DUPLEX_FULL, BIT(LINK_CAPA_20000FD) },
+	{ MAC_10000FD,  SPEED_10000,  DUPLEX_FULL, BIT(LINK_CAPA_10000FD) },
+	{ MAC_5000FD,   SPEED_5000,   DUPLEX_FULL, BIT(LINK_CAPA_5000FD) },
+	{ MAC_2500FD,   SPEED_2500,   DUPLEX_FULL, BIT(LINK_CAPA_2500FD) },
+	{ MAC_1000FD,   SPEED_1000,   DUPLEX_FULL, BIT(LINK_CAPA_1000FD) },
+	{ MAC_1000HD,   SPEED_1000,   DUPLEX_HALF, BIT(LINK_CAPA_1000HD) },
+	{ MAC_100FD,    SPEED_100,    DUPLEX_FULL, BIT(LINK_CAPA_100FD) },
+	{ MAC_100HD,    SPEED_100,    DUPLEX_HALF, BIT(LINK_CAPA_100HD) },
+	{ MAC_10FD,     SPEED_10,     DUPLEX_FULL, BIT(LINK_CAPA_10FD) },
+	{ MAC_10HD,     SPEED_10,     DUPLEX_HALF, BIT(LINK_CAPA_10HD) },
+};
+
 /**
  * phylink_caps_to_linkmodes() - Convert capabilities to ethtool link modes
  * @linkmodes: ethtool linkmode mask (must be already initialised)
@@ -445,30 +470,6 @@ static void phylink_caps_to_linkmodes(unsigned long *linkmodes,
 	}
 }
 
-static struct {
-	unsigned long mask;
-	int speed;
-	unsigned int duplex;
-} phylink_caps_params[] = {
-	{ MAC_400000FD, SPEED_400000, DUPLEX_FULL },
-	{ MAC_200000FD, SPEED_200000, DUPLEX_FULL },
-	{ MAC_100000FD, SPEED_100000, DUPLEX_FULL },
-	{ MAC_56000FD,  SPEED_56000,  DUPLEX_FULL },
-	{ MAC_50000FD,  SPEED_50000,  DUPLEX_FULL },
-	{ MAC_40000FD,  SPEED_40000,  DUPLEX_FULL },
-	{ MAC_25000FD,  SPEED_25000,  DUPLEX_FULL },
-	{ MAC_20000FD,  SPEED_20000,  DUPLEX_FULL },
-	{ MAC_10000FD,  SPEED_10000,  DUPLEX_FULL },
-	{ MAC_5000FD,   SPEED_5000,   DUPLEX_FULL },
-	{ MAC_2500FD,   SPEED_2500,   DUPLEX_FULL },
-	{ MAC_1000FD,   SPEED_1000,   DUPLEX_FULL },
-	{ MAC_1000HD,   SPEED_1000,   DUPLEX_HALF },
-	{ MAC_100FD,    SPEED_100,    DUPLEX_FULL },
-	{ MAC_100HD,    SPEED_100,    DUPLEX_HALF },
-	{ MAC_10FD,     SPEED_10,     DUPLEX_FULL },
-	{ MAC_10HD,     SPEED_10,     DUPLEX_HALF },
-};
-
 /**
  * phylink_limit_mac_speed - limit the phylink_config to a maximum speed
  * @config: pointer to a &struct phylink_config
-- 
2.48.1

[PATCH net-next v2 12/13] net: phy: phylink: Convert capabilities to linkmodes using phy_caps

[Maxime Chevallier]

phylink_caps_to_linkmodes() is used to derive a list of linkmodes that
can be conceivably exposed using a given set of speeds and duplex
through phylink's MAC capabilities.

This list can be derived from the link_caps array in phy_caps, provided
we convert the MAC capabilities into a LINK_CAPA bitmask first.

Introduce an internal phylink helper phylink_caps_to_link_caps() to
convert from MAC capabilities into phy_caps, then  phy_caps_linkmodes()
to do the link_caps -> linkmodes conversion.

This avoids having to update phylink for every new linkmode.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - new patch

 drivers/net/phy/phy-caps.h |   1 +
 drivers/net/phy/phy_caps.c |  14 ++++
 drivers/net/phy/phylink.c  | 155 +++++--------------------------------
 3 files changed, 36 insertions(+), 134 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index dd3ea9f77f1c..7b76b3204e24 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -45,6 +45,7 @@ size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 		       unsigned long *linkmodes);
 void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes);
 bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes);
+void phy_caps_linkmodes(unsigned long caps, unsigned long *linkmodes);
 
 const struct link_capabilities *
 phy_caps_lookup_by_linkmode(const unsigned long *linkmodes);
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 77bf85043e82..602e0ad44602 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -232,3 +232,17 @@ bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes)
 
 	return linkmode_intersects(link_caps[capa].linkmodes, linkmodes);
 }
+
+/**
+ * phy_caps_linkmodes() - Convert a bitfield of capabilities into linkmodes
+ * @caps: The list of caps, each bit corresponding to a LINK_CAPA value
+ * @linkmodes: The set of linkmodes to fill. Must be previously initialized.
+ */
+void phy_caps_linkmodes(unsigned long caps, unsigned long *linkmodes)
+{
+	unsigned long capa;
+
+	for_each_set_bit(capa, &caps, __LINK_CAPA_MAX)
+		linkmode_or(linkmodes, linkmodes, link_caps[capa].linkmodes);
+}
+EXPORT_SYMBOL_GPL(phy_caps_linkmodes);
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index aaf07094b821..8548c265cecf 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -317,6 +317,24 @@ static struct {
 	{ MAC_10HD,     SPEED_10,     DUPLEX_HALF, BIT(LINK_CAPA_10HD) },
 };
 
+/**
+ * phylink_caps_to_link_caps() - Convert a set of MAC capabilities LINK caps
+ * @caps: A set of MAC capabilities
+ *
+ * Returns: The corresponding set of LINK_CAPA as defined in phy-caps.h
+ */
+static unsigned long phylink_caps_to_link_caps(unsigned long caps)
+{
+	unsigned long link_caps = 0;
+	int i;
+
+	for (i = 0; i <  ARRAY_SIZE(phylink_caps_params); i++)
+		if (caps & phylink_caps_params[i].mask)
+			link_caps |= phylink_caps_params[i].caps_bit;
+
+	return link_caps;
+}
+
 /**
  * phylink_caps_to_linkmodes() - Convert capabilities to ethtool link modes
  * @linkmodes: ethtool linkmode mask (must be already initialised)
@@ -328,146 +346,15 @@ static struct {
 static void phylink_caps_to_linkmodes(unsigned long *linkmodes,
 				      unsigned long caps)
 {
+	unsigned long link_caps = phylink_caps_to_link_caps(caps);
+
 	if (caps & MAC_SYM_PAUSE)
 		__set_bit(ETHTOOL_LINK_MODE_Pause_BIT, linkmodes);
 
 	if (caps & MAC_ASYM_PAUSE)
 		__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes);
 
-	if (caps & MAC_10HD) {
-		__set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Half_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT, linkmodes);
-	}
-
-	if (caps & MAC_10FD) {
-		__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_100HD) {
-		__set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT, linkmodes);
-	}
-
-	if (caps & MAC_100FD) {
-		__set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100baseT1_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_1000HD)
-		__set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, linkmodes);
-
-	if (caps & MAC_1000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_1000baseT1_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_2500FD) {
-		__set_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_2500baseX_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_5000FD)
-		__set_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT, linkmodes);
-
-	if (caps & MAC_10000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseR_FEC_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseCR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_10000baseER_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_25000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_25000baseCR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_25000baseKR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_25000baseSR_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_40000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_50000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseKR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseKR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseSR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseCR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseLR_ER_FR_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_50000baseDR_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_56000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_100000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseSR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseCR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseKR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseSR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseCR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseLR2_ER2_FR2_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseDR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseKR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseSR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseLR_ER_FR_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseCR_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_100000baseDR_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_200000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_200000baseKR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseSR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseLR4_ER4_FR4_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseDR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseCR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseKR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseSR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseLR2_ER2_FR2_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseDR2_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_200000baseCR2_Full_BIT, linkmodes);
-	}
-
-	if (caps & MAC_400000FD) {
-		__set_bit(ETHTOOL_LINK_MODE_400000baseKR8_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseSR8_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseLR8_ER8_FR8_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseDR8_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseCR8_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseKR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseSR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseLR4_ER4_FR4_Full_BIT,
-			  linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseDR4_Full_BIT, linkmodes);
-		__set_bit(ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT, linkmodes);
-	}
+	phy_caps_linkmodes(link_caps, linkmodes);
 }
 
 /**
-- 
2.48.1

[PATCH net-next v2 13/13] net: phy: phy_caps: Allow getting an phy_interface's capabilities

[Maxime Chevallier]

Phylink has internal code to get the MAC capabilities of a given PHY
interface (what are the supported speed and duplex).

Extract that into phy_caps, but use the link_capa for conversion. Add an
internal phylink helper for the link caps -> mac caps conversion, and
use this in phylink_caps_to_linkmodes().

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
V1 -> V2: - new patch

 drivers/net/phy/phy-caps.h |  2 +
 drivers/net/phy/phy_caps.c | 92 ++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phylink.c  | 90 ++++++-------------------------------
 3 files changed, 108 insertions(+), 76 deletions(-)

diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 7b76b3204e24..2b7ed6a93e3b 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -8,6 +8,7 @@
 #define __PHY_CAPS_H
 
 #include <linux/ethtool.h>
+#include <linux/phy.h>
 
 enum {
 	LINK_CAPA_10HD = 0,
@@ -46,6 +47,7 @@ size_t phy_caps_speeds(unsigned int *speeds, size_t size,
 void phy_caps_linkmode_max_speed(u32 max_speed, unsigned long *linkmodes);
 bool phy_caps_valid(int speed, int duplex, const unsigned long *linkmodes);
 void phy_caps_linkmodes(unsigned long caps, unsigned long *linkmodes);
+unsigned long phy_caps_from_interface(phy_interface_t interface);
 
 const struct link_capabilities *
 phy_caps_lookup_by_linkmode(const unsigned long *linkmodes);
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 602e0ad44602..b04c3997df18 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -246,3 +246,95 @@ void phy_caps_linkmodes(unsigned long caps, unsigned long *linkmodes)
 		linkmode_or(linkmodes, linkmodes, link_caps[capa].linkmodes);
 }
 EXPORT_SYMBOL_GPL(phy_caps_linkmodes);
+
+/**
+ * phy_caps_from_interface() - Get the link capa from a given PHY interface
+ * @interface: The PHY interface we want to get the possible Speed/Duplex from
+ *
+ * Returns: A bitmask of LINK_CAPA_xxx values that can be achieved with the
+ *          provided interface.
+ */
+unsigned long phy_caps_from_interface(phy_interface_t interface)
+{
+	unsigned long link_caps = 0;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_USXGMII:
+		link_caps |= BIT(LINK_CAPA_10000FD) | BIT(LINK_CAPA_5000FD);
+		fallthrough;
+
+	case PHY_INTERFACE_MODE_10G_QXGMII:
+		link_caps |= BIT(LINK_CAPA_2500FD);
+		fallthrough;
+
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_PSGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+	case PHY_INTERFACE_MODE_QUSGMII:
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_GMII:
+		link_caps |= BIT(LINK_CAPA_1000HD) | BIT(LINK_CAPA_1000FD);
+		fallthrough;
+
+	case PHY_INTERFACE_MODE_REVRMII:
+	case PHY_INTERFACE_MODE_RMII:
+	case PHY_INTERFACE_MODE_SMII:
+	case PHY_INTERFACE_MODE_REVMII:
+	case PHY_INTERFACE_MODE_MII:
+		link_caps |= BIT(LINK_CAPA_10HD) | BIT(LINK_CAPA_10FD);
+		fallthrough;
+
+	case PHY_INTERFACE_MODE_100BASEX:
+		link_caps |= BIT(LINK_CAPA_100HD) | BIT(LINK_CAPA_100FD);
+		break;
+
+	case PHY_INTERFACE_MODE_TBI:
+	case PHY_INTERFACE_MODE_MOCA:
+	case PHY_INTERFACE_MODE_RTBI:
+	case PHY_INTERFACE_MODE_1000BASEX:
+		link_caps |= BIT(LINK_CAPA_1000HD);
+		fallthrough;
+	case PHY_INTERFACE_MODE_1000BASEKX:
+	case PHY_INTERFACE_MODE_TRGMII:
+		link_caps |= BIT(LINK_CAPA_1000FD);
+		break;
+
+	case PHY_INTERFACE_MODE_2500BASEX:
+		link_caps |= BIT(LINK_CAPA_2500FD);
+		break;
+
+	case PHY_INTERFACE_MODE_5GBASER:
+		link_caps |= BIT(LINK_CAPA_5000FD);
+		break;
+
+	case PHY_INTERFACE_MODE_XGMII:
+	case PHY_INTERFACE_MODE_RXAUI:
+	case PHY_INTERFACE_MODE_XAUI:
+	case PHY_INTERFACE_MODE_10GBASER:
+	case PHY_INTERFACE_MODE_10GKR:
+		link_caps |= BIT(LINK_CAPA_10000FD);
+		break;
+
+	case PHY_INTERFACE_MODE_25GBASER:
+		link_caps |= BIT(LINK_CAPA_25000FD);
+		break;
+
+	case PHY_INTERFACE_MODE_XLGMII:
+		link_caps |= BIT(LINK_CAPA_40000FD);
+		break;
+
+	case PHY_INTERFACE_MODE_INTERNAL:
+		link_caps |= GENMASK(__LINK_CAPA_LAST, 0);
+		break;
+
+	case PHY_INTERFACE_MODE_NA:
+	case PHY_INTERFACE_MODE_MAX:
+		break;
+	}
+
+	return link_caps;
+}
+EXPORT_SYMBOL_GPL(phy_caps_from_interface);
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 8548c265cecf..8a48aff72df6 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -335,6 +335,18 @@ static unsigned long phylink_caps_to_link_caps(unsigned long caps)
 	return link_caps;
 }
 
+static unsigned long phylink_link_caps_to_mac_caps(unsigned long link_caps)
+{
+	unsigned long caps = 0;
+	int i;
+
+	for (i = 0; i <  ARRAY_SIZE(phylink_caps_params); i++)
+		if (link_caps & phylink_caps_params[i].caps_bit)
+			caps |= phylink_caps_params[i].mask;
+
+	return caps;
+}
+
 /**
  * phylink_caps_to_linkmodes() - Convert capabilities to ethtool link modes
  * @linkmodes: ethtool linkmode mask (must be already initialised)
@@ -412,86 +424,12 @@ static unsigned long phylink_get_capabilities(phy_interface_t interface,
 					      unsigned long mac_capabilities,
 					      int rate_matching)
 {
+	unsigned long link_caps = phy_caps_from_interface(interface);
 	int max_speed = phylink_interface_max_speed(interface);
 	unsigned long caps = MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
 	unsigned long matched_caps = 0;
 
-	switch (interface) {
-	case PHY_INTERFACE_MODE_USXGMII:
-		caps |= MAC_10000FD | MAC_5000FD;
-		fallthrough;
-
-	case PHY_INTERFACE_MODE_10G_QXGMII:
-		caps |= MAC_2500FD;
-		fallthrough;
-
-	case PHY_INTERFACE_MODE_RGMII_TXID:
-	case PHY_INTERFACE_MODE_RGMII_RXID:
-	case PHY_INTERFACE_MODE_RGMII_ID:
-	case PHY_INTERFACE_MODE_RGMII:
-	case PHY_INTERFACE_MODE_PSGMII:
-	case PHY_INTERFACE_MODE_QSGMII:
-	case PHY_INTERFACE_MODE_QUSGMII:
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_GMII:
-		caps |= MAC_1000HD | MAC_1000FD;
-		fallthrough;
-
-	case PHY_INTERFACE_MODE_REVRMII:
-	case PHY_INTERFACE_MODE_RMII:
-	case PHY_INTERFACE_MODE_SMII:
-	case PHY_INTERFACE_MODE_REVMII:
-	case PHY_INTERFACE_MODE_MII:
-		caps |= MAC_10HD | MAC_10FD;
-		fallthrough;
-
-	case PHY_INTERFACE_MODE_100BASEX:
-		caps |= MAC_100HD | MAC_100FD;
-		break;
-
-	case PHY_INTERFACE_MODE_TBI:
-	case PHY_INTERFACE_MODE_MOCA:
-	case PHY_INTERFACE_MODE_RTBI:
-	case PHY_INTERFACE_MODE_1000BASEX:
-		caps |= MAC_1000HD;
-		fallthrough;
-	case PHY_INTERFACE_MODE_1000BASEKX:
-	case PHY_INTERFACE_MODE_TRGMII:
-		caps |= MAC_1000FD;
-		break;
-
-	case PHY_INTERFACE_MODE_2500BASEX:
-		caps |= MAC_2500FD;
-		break;
-
-	case PHY_INTERFACE_MODE_5GBASER:
-		caps |= MAC_5000FD;
-		break;
-
-	case PHY_INTERFACE_MODE_XGMII:
-	case PHY_INTERFACE_MODE_RXAUI:
-	case PHY_INTERFACE_MODE_XAUI:
-	case PHY_INTERFACE_MODE_10GBASER:
-	case PHY_INTERFACE_MODE_10GKR:
-		caps |= MAC_10000FD;
-		break;
-
-	case PHY_INTERFACE_MODE_25GBASER:
-		caps |= MAC_25000FD;
-		break;
-
-	case PHY_INTERFACE_MODE_XLGMII:
-		caps |= MAC_40000FD;
-		break;
-
-	case PHY_INTERFACE_MODE_INTERNAL:
-		caps |= ~0;
-		break;
-
-	case PHY_INTERFACE_MODE_NA:
-	case PHY_INTERFACE_MODE_MAX:
-		break;
-	}
+	caps |= phylink_link_caps_to_mac_caps(link_caps);
 
 	switch (rate_matching) {
 	case RATE_MATCH_OPEN_LOOP:
-- 
2.48.1

Re: [PATCH net-next v2 09/13] net: phy: phylink: Use phy_caps_lookup for fixed-link configuration

[Russell King (Oracle)]

Please use a subject line of "net: phylink: " for phylink patches, not
"net: phy: " which is for phylib.

On Wed, Feb 26, 2025 at 11:09:24AM +0100, Maxime Chevallier wrote:
> When phylink creates a fixed-link configuration, it finds a matching
> linkmode to set as the advertised, lp_advertising and supported modes
> based on the speed and duplex of the fixed link.
> 
> Use the newly introduced phy_caps_lookup to get these modes instead of
> phy_lookup_settings(). This has the side effect that the matched
> settings and configured linkmodes may now contain several linkmodes (the
> intersection of supported linkmodes from the phylink settings and the
> linkmodes that match speed/duplex) instead of the one from
> phy_lookup_settings().
> 
> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> ---
> V1 -> V2: - fixed pl->link_config.lp_advertising setting
> 
>  drivers/net/phy/phylink.c | 26 +++++++++++++++-----------
>  1 file changed, 15 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
> index 6c67d5c9b787..63fbf3d8708a 100644
> --- a/drivers/net/phy/phylink.c
> +++ b/drivers/net/phy/phylink.c
> @@ -805,9 +805,10 @@ static int phylink_validate(struct phylink *pl, unsigned long *supported,
>  static int phylink_parse_fixedlink(struct phylink *pl,
>  				   const struct fwnode_handle *fwnode)
>  {
> +	__ETHTOOL_DECLARE_LINK_MODE_MASK(match) = { 0, };
>  	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +	const struct link_capabilities *c;
>  	struct fwnode_handle *fixed_node;
> -	const struct phy_setting *s;
>  	struct gpio_desc *desc;
>  	u32 speed;
>  	int ret;
> @@ -879,8 +880,10 @@ static int phylink_parse_fixedlink(struct phylink *pl,
>  	linkmode_copy(pl->link_config.advertising, pl->supported);
>  	phylink_validate(pl, pl->supported, &pl->link_config);
>  
> -	s = phy_lookup_setting(pl->link_config.speed, pl->link_config.duplex,
> -			       pl->supported, true);
> +	c = phy_caps_lookup(pl->link_config.speed, pl->link_config.duplex,
> +			    pl->supported, true);
> +	if (c)
> +		linkmode_and(match, pl->supported, c->linkmodes);

What's this for? Surely phy_caps_lookup() should not return a link mode
that wasn't in phy_caps_lookup()'s 3rd argument.

Otherwise...

>  	linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT, mask);
>  	linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, mask);
> @@ -889,9 +892,10 @@ static int phylink_parse_fixedlink(struct phylink *pl,
>  
>  	phylink_set(pl->supported, MII);
>  
> -	if (s) {
> -		__set_bit(s->bit, pl->supported);
> -		__set_bit(s->bit, pl->link_config.lp_advertising);
> +	if (c) {
> +		linkmode_or(pl->supported, pl->supported, match);
> +		linkmode_or(pl->link_config.lp_advertising,
> +			    pl->link_config.lp_advertising, match);
>  	} else {
>  		phylink_warn(pl, "fixed link %s duplex %dMbps not recognised\n",
>  			     pl->link_config.duplex == DUPLEX_FULL ? "full" : "half",
> @@ -1879,21 +1883,21 @@ static int phylink_register_sfp(struct phylink *pl,
>  int phylink_set_fixed_link(struct phylink *pl,
>  			   const struct phylink_link_state *state)
>  {
> -	const struct phy_setting *s;
> +	const struct link_capabilities *c;
>  	unsigned long *adv;
>  
>  	if (pl->cfg_link_an_mode != MLO_AN_PHY || !state ||
>  	    !test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state))
>  		return -EINVAL;
>  
> -	s = phy_lookup_setting(state->speed, state->duplex,
> -			       pl->supported, true);
> -	if (!s)
> +	c = phy_caps_lookup(state->speed, state->duplex,
> +			    pl->supported, true);
> +	if (!c)
>  		return -EINVAL;
>  
>  	adv = pl->link_config.advertising;
>  	linkmode_zero(adv);
> -	linkmode_set_bit(s->bit, adv);
> +	linkmode_and(adv, pl->supported, c->linkmodes);

... this is wrong since this is basically doing the same as the above
parsing.

I'm not sure why you're generating different code for what is
essentially the same thing.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH net-next v2 11/13] net: phy: phylink: Add a mapping between MAC_CAPS and LINK_CAPS

[Russell King (Oracle)]

On Wed, Feb 26, 2025 at 11:09:26AM +0100, Maxime Chevallier wrote:
> phylink allows MAC drivers to report the capabilities in terms of speed,
> duplex and pause support. This is done through a dedicated set of enum
> values in the form of the MAC_ capabilities. They are very close to what
> the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
> have any information about Pause/Asym Pause support.
> 
> To prepare converting phylink to using the phy_caps, add the mapping
> between MAC capabilities and phy_caps. While doing so, we move the
> phylink_caps_params array up a bit to simplify future commits.

I still want to know why we need to do this type of thing -
unfortunately I don't have time to review all your patches at the
moment. I haven't reviewed all your patches since you've started
posting them. Sorry.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH net-next v2 11/13] net: phy: phylink: Add a mapping between MAC_CAPS and LINK_CAPS

[Maxime Chevallier]

Hello Russell,

On Wed, 26 Feb 2025 14:03:20 +0000
"Russell King (Oracle)" <linux@armlinux.org.uk> wrote:

> On Wed, Feb 26, 2025 at 11:09:26AM +0100, Maxime Chevallier wrote:
> > phylink allows MAC drivers to report the capabilities in terms of speed,
> > duplex and pause support. This is done through a dedicated set of enum
> > values in the form of the MAC_ capabilities. They are very close to what
> > the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
> > have any information about Pause/Asym Pause support.
> > 
> > To prepare converting phylink to using the phy_caps, add the mapping
> > between MAC capabilities and phy_caps. While doing so, we move the
> > phylink_caps_params array up a bit to simplify future commits.  
> 
> I still want to know why we need to do this type of thing -

Sorry not to have included more details on the why. The main reason is
for the phy_port work. In the previous phy_port series [1] I included an
attempt at making a first step forward with PHY-driven SFP, so that
phylib itself provides the sfp_upstream_ops and not individual PHY
drivers. That's to get a better handling for multi-port PHYs, which is
one of the end-goals.

[1]: https://lore.kernel.org/netdev/20250213101606.1154014-1-maxime.chevallier@bootlin.com/

As part of that PHY-sfp work, I find it very useful for PHY drivers to
be able to tell what phy_interface_t they can expose on their serdes
interfaces, and from then build a list of linkmodes to get an idea of
what we can support on that port. That's why I'm extracting that out of
phylink.

I did see that you suggested having phylink involved for PHY sfp maybe,
but TBH I don't even know where to start, so I took a safer approach
with phylib-driven SFPs.

> unfortunately I don't have time to review all your patches at the
> moment. I haven't reviewed all your patches since you've started
> posting them. Sorry.

No worries, I understand that that whole work is quite the mouthful and
implies some involved reviews. But even discussing higher level stuff,
like we do now, helps me steer that work in the right direction and
hopefully make it easier for you and the other PHY maintainers to
review that in the future.

Maxime

Re: [PATCH net-next v2 09/13] net: phy: phylink: Use phy_caps_lookup for fixed-link configuration

[Maxime Chevallier]

Hi Russell,

On Wed, 26 Feb 2025 14:01:57 +0000
"Russell King (Oracle)" <linux@armlinux.org.uk> wrote:

> Please use a subject line of "net: phylink: " for phylink patches, not
> "net: phy: " which is for phylib.

Sure thing, I wasn't sure about the subject line for this one.

> On Wed, Feb 26, 2025 at 11:09:24AM +0100, Maxime Chevallier wrote:
> > When phylink creates a fixed-link configuration, it finds a matching
> > linkmode to set as the advertised, lp_advertising and supported modes
> > based on the speed and duplex of the fixed link.
> > 
> > Use the newly introduced phy_caps_lookup to get these modes instead of
> > phy_lookup_settings(). This has the side effect that the matched
> > settings and configured linkmodes may now contain several linkmodes (the
> > intersection of supported linkmodes from the phylink settings and the
> > linkmodes that match speed/duplex) instead of the one from
> > phy_lookup_settings().
> > 
> > Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>

[...]

> > @@ -879,8 +880,10 @@ static int phylink_parse_fixedlink(struct phylink *pl,
> >  	linkmode_copy(pl->link_config.advertising, pl->supported);
> >  	phylink_validate(pl, pl->supported, &pl->link_config);
> >  
> > -	s = phy_lookup_setting(pl->link_config.speed, pl->link_config.duplex,
> > -			       pl->supported, true);
> > +	c = phy_caps_lookup(pl->link_config.speed, pl->link_config.duplex,
> > +			    pl->supported, true);
> > +	if (c)
> > +		linkmode_and(match, pl->supported, c->linkmodes);  
> 
> What's this for? Surely phy_caps_lookup() should not return a link mode
> that wasn't in phy_caps_lookup()'s 3rd argument.

The new lookup may return a linkmode that wasn't in the 3rd argument,
as it will return ALL linkmodes that matched speed and duplex, provided
that at least one of said linkmodes matched the 3rd parameter.

Say you pass SPEED_1000, DUPLEX_FULL and a bitset containing only
1000BaseTFull, you'll get :

 - 1000BaseTFull, 1000BaseKX, 1000BaseT1, etc. in c->linkmodes.

That's the reason for re-andf'ing the modes afterwards.

If that API is too convoluted or error-prone, I can come up with an API
returning only what matched.

Maxime