Re: [RFC PATCH net-next] net: dsa: mt7530: fix port specifications for MT7988

["Russell King (Oracle)" <linux@armlinux.org.uk>]

On Thu, Apr 06, 2023 at 01:04:45PM +0300, arinc9.unal@gmail.com wrote:
> From: Arınç ÜNAL <arinc.unal@arinc9.com>
> 
> On the switch on the MT7988 SoC, there are only 4 PHYs. There's only port 6
> as the CPU port, there's no port 5. Split the switch statement with a check
> to enforce these for the switch on the MT7988 SoC. The internal phy-mode is
> specific to MT7988 so put it for MT7988 only.
> 
> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
> ---
> 
> Daniel, this is based on the information you provided me about the switch.
> I will add this to my current patch series if it looks good to you.
> 
> Arınç
> 
> ---
>  drivers/net/dsa/mt7530.c | 67 ++++++++++++++++++++++++++--------------
>  1 file changed, 43 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index 6fbbdcb5987f..f167fa135ef1 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -2548,7 +2548,7 @@ static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
>  	phy_interface_zero(config->supported_interfaces);
>  
>  	switch (port) {
> -	case 0 ... 4: /* Internal phy */
> +	case 0 ... 3: /* Internal phy */
>  		__set_bit(PHY_INTERFACE_MODE_INTERNAL,
>  			  config->supported_interfaces);
>  		break;
> @@ -2710,37 +2710,56 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
>  	struct mt7530_priv *priv = ds->priv;
>  	u32 mcr_cur, mcr_new;
>  
> -	switch (port) {
> -	case 0 ... 4: /* Internal phy */
> -		if (state->interface != PHY_INTERFACE_MODE_GMII &&
> -		    state->interface != PHY_INTERFACE_MODE_INTERNAL)
> -			goto unsupported;
> -		break;
> -	case 5: /* Port 5, a CPU port. */
> -		if (priv->p5_interface == state->interface)
> +	if (priv->id == ID_MT7988) {
> +		switch (port) {
> +		case 0 ... 3: /* Internal phy */
> +			if (state->interface != PHY_INTERFACE_MODE_INTERNAL)

How do these end up with PHY_INTERFACE_MODE_INTERNAL ? phylib defaults
to GMII mode without something else being specified in DT.

Also note that you should *not* be validating state->interface in the
mac_config() method because it's way too late to reject it - if you get
an unsupported interface here, then that is down to the get_caps()
method being buggy. Only report interfaces in get_caps() that you are
prepared to handle in the rest of the system.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!