From: Vinod Koul <vkoul@kernel.org>
To: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>,
Heiner Kallweit <hkallweit1@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Maxime Chevallier <maxime.chevallier@bootlin.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>,
Neil Armstrong <neil.armstrong@linaro.org>,
netdev@vger.kernel.org, Paolo Abeni <pabeni@redhat.com>
Subject: Re: [PATCH net-next 03/14] phy: qcom-sgmii-eth: add .set_mode() and .validate() methods
Date: Wed, 21 Jan 2026 12:40:14 +0530 [thread overview]
Message-ID: <aXB71tN-mf6xBVFc@vaman> (raw)
In-Reply-To: <E1vhoS7-00000005H1T-1dXt@rmk-PC.armlinux.org.uk>
On 19-01-26, 12:33, Russell King (Oracle) wrote:
> qcom-sgmii-eth is an Ethernet SerDes supporting only Ethernet mode
> using SGMII, 1000BASE-X and 2500BASE-X.
>
> Add an implementation of the .set_mode() method, which can be used
> instead of or as well as the .set_speed() method. The Ethernet
> interface modes mentioned above all have a fixed data rate, so
> setting the mode is sufficient to fully specify the operating
> parameters.
>
> Add an implementation of the .validate() method, which will be
> necessary to allow discovery of the SerDes capabilities for platform
> independent SerDes support in the stmmac network driver.
Acked-by: Vinod Koul <vkoul@kernel.org>
--
~Vinod
next prev parent reply other threads:[~2026-01-21 7:10 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-19 12:32 [PATCH net-next 00/14] net: stmmac: SerDes, PCS, BASE-X, and inband goodies Russell King (Oracle)
2026-01-19 12:33 ` [PATCH net-next 01/14] net: stmmac: qcom-ethqos: remove mac_base Russell King (Oracle)
2026-01-19 13:59 ` Bartosz Golaszewski
2026-01-19 12:33 ` [PATCH net-next 02/14] net: stmmac: qcom-ethqos: convert to set_clk_tx_rate() method Russell King (Oracle)
2026-01-19 14:00 ` Bartosz Golaszewski
2026-01-19 12:33 ` [PATCH net-next 03/14] phy: qcom-sgmii-eth: add .set_mode() and .validate() methods Russell King (Oracle)
2026-01-19 14:00 ` Bartosz Golaszewski
2026-01-21 7:10 ` Vinod Koul [this message]
2026-01-19 12:33 ` [PATCH net-next 04/14] net: stmmac: wrap phylink's rx_clk_stop functions Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 05/14] net: stmmac: add stmmac core serdes support Russell King (Oracle)
2026-01-19 19:21 ` [net-next,05/14] " Jakub Kicinski
2026-01-20 5:04 ` Russell King (Oracle)
2026-01-20 8:18 ` Vladimir Oltean
2026-01-20 10:12 ` Russell King (Oracle)
2026-01-20 12:11 ` Vladimir Oltean
2026-01-21 14:46 ` Russell King (Oracle)
2026-01-21 16:23 ` Vladimir Oltean
2026-01-21 17:33 ` Russell King (Oracle)
2026-01-22 11:29 ` Vladimir Oltean
2026-01-20 8:42 ` Vladimir Oltean
2026-01-20 10:14 ` Russell King (Oracle)
2026-01-20 23:32 ` Jakub Kicinski
2026-01-19 12:34 ` [PATCH net-next 06/14] net: stmmac: qcom-ethqos: convert to dwmac generic SerDes support Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 07/14] net: stmmac: move most PCS register definitions to stmmac_pcs.c Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 08/14] net: stmmac: handle integrated PCS phy_intf_sel separately Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 09/14] net: stmmac: add BASE-X support to integrated PCS Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 10/14] net: stmmac: use integrated PCS for BASE-X modes Russell King (Oracle)
2026-01-19 13:20 ` Maxime Chevallier
2026-01-19 12:34 ` [PATCH net-next 11/14] net: stmmac: add struct stmmac_pcs_info Russell King (Oracle)
2026-01-19 13:23 ` Maxime Chevallier
2026-01-19 12:34 ` [PATCH net-next 12/14] net: stmmac: add support for reading inband SGMII status Russell King (Oracle)
2026-01-19 19:21 ` [net-next,12/14] " Jakub Kicinski
2026-01-19 12:34 ` [PATCH net-next 13/14] net: stmmac: configure SGMII AN control according to phylink Russell King (Oracle)
2026-01-19 12:34 ` [PATCH net-next 14/14] net: stmmac: report PCS configuration changes Russell King (Oracle)
2026-01-19 14:27 ` Russell King (Oracle)
-- strict thread matches above, loose matches on Subject: below --
2026-01-14 17:44 [PATCH RFC net-next 00/14] net: stmmac: SerDes, PCS, BASE-X, and inband goodies Russell King (Oracle)
2026-01-14 17:45 ` [PATCH net-next 03/14] phy: qcom-sgmii-eth: add .set_mode() and .validate() methods Russell King (Oracle)
2026-01-14 18:47 ` Vladimir Oltean
2026-01-14 18:55 ` Russell King (Oracle)
2026-01-14 19:02 ` Vladimir Oltean
2026-01-15 10:11 ` kernel test robot
2026-01-15 10:23 ` kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aXB71tN-mf6xBVFc@vaman \
--to=vkoul@kernel.org \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=maxime.chevallier@bootlin.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=mohd.anwar@oss.qualcomm.com \
--cc=neil.armstrong@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=rmk+kernel@armlinux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox