> With more tx queues on one end of a veth pair than rx queues on the
> other, and RPS or generic XDP enabled on the receiving end, we get:
> 
>     veth1 received packet on queue 2, but number of RX queues is 2
>     WARNING: net/core/dev.c:5212 at get_rps_cpu+0x560/0x1360
>     Call Trace:
>      <TASK>
>      netif_rx_internal+0x1af/0x4c0
>      __netif_rx+0x99/0x350
>      veth_xmit+0x713/0xca0
>      dev_hard_start_xmit+0x166/0x5f0
>      __dev_queue_xmit+0x1797/0x42d0
>      ip_finish_output2+0xa34/0x1f40
>      __ip_finish_output+0x510/0x7e0
>      ip_finish_output+0x2f/0x320
>      ip_output+0x17a/0x3f0
>      ip_send_skb+0x1bc/0x220
>      ......
> 
> Easy to hit with "ethtool -L veth0 tx 4", "ethtool -L veth1 rx 2",
> rps_cpus set on veth1 and a few flows sent over the pair [1].
> 
> veth_xmit() uses skb->queue_mapping to pick the peer rq, but never
> clears it before veth_forward_skb(), so the rx side still sees the tx
> queue index. Everything on the rx side that goes through
> skb_get_rx_queue(), like get_rps_cpu() and netif_get_rxqueue() for
> generic XDP, takes it as a recorded rx queue and warns once it is out
> of range.
> 
> Clear it before handing the skb to the peer:
> 
> - It is the tx queue index of this device, it says nothing about the
>   rx queue of the peer.
> 
> - The two sides don't even agree on the encoding. The tx side stores
>   the index as is, the rx side stores index + 1 so that 0 can mean
>   "not recorded". So tx queue k is read back as rx queue k - 1, and
>   tx queue 0 as "not recorded".
> 
> - Commit 710ad98c363a ("veth: Do not record rx queue hint in
>   veth_xmit") already decided that veth should not pass any queue
>   hint to the peer. There is no tx->rx queue mapping to preserve, so
>   nothing is lost by clearing it.
> 
> On NETDEV_TX_BUSY the skb goes back to the qdisc, which looks up the
> txq from skb->queue_mapping to decide when to retry, so restore it
> there, next to the existing __skb_push().
> 
> [1]: https://lore.kernel.org/netdev/156834bb-8e40-496e-9443-9d515fa18eab@linux.dev/
> 
> Fixes: 710ad98c363a ("veth: Do not record rx queue hint in veth_xmit")
> Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>

Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@oss.qualcomm.com>

> ---
> Target net-next since it is moderate.
> Full reproducer, veth1 lives in netns ns1:
> 
>   ip netns add ns1
>   ip link add veth0 type veth peer name veth1
>   ip link set veth1 netns ns1
>   ethtool -L veth0  tx 4
>   ip netns exec ns1 ethtool -L veth1 rx 2
>   ip netns exec ns1 sh -c  'echo f > /sys/class/net/veth1/queues/rx-0/rps_cpus'
>   ip addr add 10.9.9.1/24 dev veth0
>   ip link set veth0 up
>   ip netns exec ns1 ip addr add 10.9.9.2/24 dev veth1
>   ip netns exec ns1 ip link set veth1 up
>   for i in $(seq 200); do echo hi > /dev/udp/10.9.9.2/9999; done
> ---
>  drivers/net/veth.c | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/drivers/net/veth.c b/drivers/net/veth.c
> index 71227d0389aa..7d181c5e387b 100644
> --- a/drivers/net/veth.c
> +++ b/drivers/net/veth.c
> @@ -377,6 +377,9 @@ static netdev_tx_t veth_xmit(struct sk_buff *skb, struct net_device *dev)
>  
>  	skb_tx_timestamp(skb);
>  
> +	/* tx queue index of this device, meaningless as rx queue of the peer */
> +	skb_set_queue_mapping(skb, 0);
> +
>  	ret = veth_forward_skb(rcv, skb, rq, use_napi);
>  	switch (ret) {
>  	case NET_RX_SUCCESS: /* same as NETDEV_TX_OK */
> @@ -397,6 +400,8 @@ static netdev_tx_t veth_xmit(struct sk_buff *skb, struct net_device *dev)
>  		}
>  		/* Restore Eth hdr pulled by dev_forward_skb/eth_type_trans */
>  		__skb_push(skb, ETH_HLEN);
> +		/* qdisc requeues the skb on the txq it points to */
> +		skb_set_queue_mapping(skb, rxq);
>  		netif_tx_stop_queue(txq);
>  		/* Makes sure NAPI peer consumer runs. Consumer is responsible
>  		 * for starting txq again, until then ndo_start_xmit (this
> -- 
> 2.43.0
> 
>