From: Florian Fainelli <f.fainelli@gmail.com>
To: Andrew Lunn <andrew@lunn.ch>, David Miller <davem@davemloft.net>
Cc: netdev <netdev@vger.kernel.org>, maxime.chevallier@bootlin.com
Subject: Re: [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half
Date: Mon, 3 Sep 2018 10:46:35 -0700 [thread overview]
Message-ID: <cec12e14-1239-6dfb-177a-d653a166fb0e@gmail.com> (raw)
In-Reply-To: <1535908001-18593-3-git-send-email-andrew@lunn.ch>
On 9/2/2018 10:06 AM, Andrew Lunn wrote:
> The driver indicates it can do 10/100 full and half duplex, plus 1G
> Full. The datasheet indicates 1G half is also supported. So make use
> of the standard PHY_GBIT_FEATURES.
>
> It could be, this was added because there is a MAC which does not
> support 1G half. Bit this is the wrong place to enforce this.
Indeed, this should not be left to the PHY to decide, although in my
experience using 1000/Half is always a "roll the dice" thing, since it
is not AFAIR properly specified.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
--
Florian
next prev parent reply other threads:[~2018-09-03 22:08 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-09-02 17:06 [PATCH net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause Andrew Lunn
2018-09-03 17:53 ` Florian Fainelli
2018-09-04 1:20 ` Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half Andrew Lunn
2018-09-03 17:46 ` Florian Fainelli [this message]
2018-09-02 17:06 ` [PATCH net-next 03/12] net: phy: bcm63xx: Allow to be built with COMPILE_TEST Andrew Lunn
2018-09-03 17:28 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 04/12] net: ethernet: Use phy_set_max_speed() to limit advertised speed Andrew Lunn
2018-09-03 17:31 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 05/12] net: ethernet: genet: Fix speed selection Andrew Lunn
2018-09-03 17:32 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 06/12] net: ethernet: Fix up drivers masking pause support Andrew Lunn
2018-09-03 17:33 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 07/12] net: ethernet: Add helper to remove a supported link mode Andrew Lunn
2018-09-03 17:35 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 08/12] net: ethernet: Add helper for MACs which support asym pause Andrew Lunn
2018-09-03 17:38 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 09/12] net: ethernet: Add helper for MACs which support pause Andrew Lunn
2018-09-03 17:39 ` Florian Fainelli
2018-09-03 19:54 ` Andrew Lunn
2018-09-02 17:06 ` [PATCH net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause Andrew Lunn
2018-09-03 17:49 ` Florian Fainelli
2018-09-03 19:58 ` Andrew Lunn
2018-09-03 22:30 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause Andrew Lunn
2018-09-03 17:49 ` Florian Fainelli
2018-09-02 17:06 ` [PATCH net-next 12/12] net: ethernet: Add helper to determine if pause configuration is supported Andrew Lunn
2018-09-03 17:52 ` Florian Fainelli
2018-09-04 2:44 ` [PATCH net-next 00/12] Preparing for phylib limkmodes David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cec12e14-1239-6dfb-177a-d653a166fb0e@gmail.com \
--to=f.fainelli@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=maxime.chevallier@bootlin.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).