* [PATCH v6 1/3] stmmac: adding DT parameter for LPI tx clock gating
2017-01-09 12:35 [PATCH v6 0/3] adding new glue driver dwmac-dwc-qos-eth Joao Pinto
@ 2017-01-09 12:35 ` Joao Pinto
2017-01-09 12:35 ` [PATCH v6 2/3] stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure Joao Pinto
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Joao Pinto @ 2017-01-09 12:35 UTC (permalink / raw)
To: davem
Cc: lars.persson, niklass, swarren, treding, netdev, nathan.sullivan,
Joao Pinto
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
---
changes v5 -> v6:
- rebased master branch to achieve clean patch
changes v1 -> v5:
- Nothing changed, just to keep up patch set version
Documentation/devicetree/bindings/net/stmmac.txt | 2 ++
drivers/net/ethernet/stmicro/stmmac/common.h | 3 ++-
drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 5 ++++-
drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 6 +++++-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 ++-
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 +++
include/linux/stmmac.h | 1 +
8 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index c3d2fd4..d3bfc2b 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -49,6 +49,8 @@ Optional properties:
- snps,force_sf_dma_mode Force DMA to use the Store and Forward
mode for both tx and rx. This flag is
ignored if force_thresh_dma_mode is set.
+- snps,en-tx-lpi-clockgating Enable gating of the MAC TX clock during
+ TX low-power mode
- snps,multicast-filter-bins: Number of multicast filter hash bins
supported by this device instance
- snps,perfect-filter-entries: Number of perfect filter entries supported
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
index 6c96291..75e2666 100644
--- a/drivers/net/ethernet/stmicro/stmmac/common.h
+++ b/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -476,7 +476,8 @@ struct stmmac_ops {
unsigned int reg_n);
void (*get_umac_addr)(struct mac_device_info *hw, unsigned char *addr,
unsigned int reg_n);
- void (*set_eee_mode)(struct mac_device_info *hw);
+ void (*set_eee_mode)(struct mac_device_info *hw,
+ bool en_tx_lpi_clockgating);
void (*reset_eee_mode)(struct mac_device_info *hw);
void (*set_eee_timer)(struct mac_device_info *hw, int ls, int tw);
void (*set_eee_pls)(struct mac_device_info *hw, int link);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
index be3c91c..a5ffca1 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
@@ -343,11 +343,14 @@ static int dwmac1000_irq_status(struct mac_device_info *hw,
return ret;
}
-static void dwmac1000_set_eee_mode(struct mac_device_info *hw)
+static void dwmac1000_set_eee_mode(struct mac_device_info *hw,
+ bool en_tx_lpi_clockgating)
{
void __iomem *ioaddr = hw->pcsr;
u32 value;
+ /*TODO - en_tx_lpi_clockgating treatment */
+
/* Enable the link status receive on RGMII, SGMII ore SMII
* receive path and instruct the transmit to enter in LPI
* state.
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
index 73d1dab..db45134 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
@@ -98,6 +98,7 @@ enum power_event {
#define GMAC4_LPI_TIMER_CTRL 0xd4
/* LPI control and status defines */
+#define GMAC4_LPI_CTRL_STATUS_LPITCSE BIT(21) /* LPI Tx Clock Stop Enable */
#define GMAC4_LPI_CTRL_STATUS_LPITXA BIT(19) /* Enable LPI TX Automate */
#define GMAC4_LPI_CTRL_STATUS_PLS BIT(17) /* PHY Link Status */
#define GMAC4_LPI_CTRL_STATUS_LPIEN BIT(16) /* LPI Enable */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
index 02eab79..834f40f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -137,7 +137,8 @@ static void dwmac4_get_umac_addr(struct mac_device_info *hw,
GMAC_ADDR_LOW(reg_n));
}
-static void dwmac4_set_eee_mode(struct mac_device_info *hw)
+static void dwmac4_set_eee_mode(struct mac_device_info *hw,
+ bool en_tx_lpi_clockgating)
{
void __iomem *ioaddr = hw->pcsr;
u32 value;
@@ -149,6 +150,9 @@ static void dwmac4_set_eee_mode(struct mac_device_info *hw)
value = readl(ioaddr + GMAC4_LPI_CTRL_STATUS);
value |= GMAC4_LPI_CTRL_STATUS_LPIEN | GMAC4_LPI_CTRL_STATUS_LPITXA;
+ if (en_tx_lpi_clockgating)
+ value |= GMAC4_LPI_CTRL_STATUS_LPITCSE;
+
writel(value, ioaddr + GMAC4_LPI_CTRL_STATUS);
}
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 92ac006..fa0b4de 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -239,7 +239,8 @@ static void stmmac_enable_eee_mode(struct stmmac_priv *priv)
/* Check and enter in LPI mode */
if ((priv->dirty_tx == priv->cur_tx) &&
(priv->tx_path_in_lpi_mode == false))
- priv->hw->mac->set_eee_mode(priv->hw);
+ priv->hw->mac->set_eee_mode(priv->hw,
+ priv->plat->en_tx_lpi_clockgating);
}
/**
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 60ba899..78ccb50 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -248,6 +248,9 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
plat->force_sf_dma_mode =
of_property_read_bool(np, "snps,force_sf_dma_mode");
+ plat->en_tx_lpi_clockgating =
+ of_property_read_bool(np, "snps,en-tx-lpi-clockgating");
+
/* Set the maxmtu to a default of JUMBO_LEN in case the
* parameter is not present in the device tree.
*/
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 889e0e9..e3cd758 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -142,5 +142,6 @@ struct plat_stmmacenet_data {
int has_gmac4;
bool tso_en;
int mac_port_sel_speed;
+ bool en_tx_lpi_clockgating;
};
#endif
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v6 2/3] stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure
2017-01-09 12:35 [PATCH v6 0/3] adding new glue driver dwmac-dwc-qos-eth Joao Pinto
2017-01-09 12:35 ` [PATCH v6 1/3] stmmac: adding DT parameter for LPI tx clock gating Joao Pinto
@ 2017-01-09 12:35 ` Joao Pinto
2017-01-09 12:35 ` [PATCH v6 3/3] stmmac: adding new glue driver dwmac-dwc-qos-eth Joao Pinto
2017-01-09 19:54 ` [PATCH v6 0/3] " David Miller
3 siblings, 0 replies; 5+ messages in thread
From: Joao Pinto @ 2017-01-09 12:35 UTC (permalink / raw)
To: davem
Cc: lars.persson, niklass, swarren, treding, netdev, nathan.sullivan,
Joao Pinto
This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:
a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right
b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
---
changes v5 -> v6:
- rebased master branch to achieve clean patch
changes v3 -> v5:
- Nothing changed, just to keep up patch set version
changes v2 -> v3:
- dwmac-socfpga glue driver was also using stmmac_rst from priv struct and
was causing a build error caught by kbuild robot
changes v1 -> v2:
- Nothing changed, just to keep up patch set version
.../net/ethernet/stmicro/stmmac/dwmac-socfpga.c | 2 +-
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 5 --
.../net/ethernet/stmicro/stmmac/stmmac_ethtool.c | 4 +-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 82 ++++------------------
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 47 +++++++++++++
include/linux/stmmac.h | 5 ++
6 files changed, 70 insertions(+), 75 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
index 1f99702..17d4bba 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -341,7 +341,7 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
* mode. Create a copy of the core reset handle so it can be used by
* the driver later.
*/
- dwmac->stmmac_rst = stpriv->stmmac_rst;
+ dwmac->stmmac_rst = stpriv->plat->stmmac_rst;
ret = socfpga_dwmac_set_phy_mode(dwmac);
if (ret)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index eab04ae..bf8a83e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -106,9 +106,6 @@ struct stmmac_priv {
u32 msg_enable;
int wolopts;
int wol_irq;
- struct clk *stmmac_clk;
- struct clk *pclk;
- struct reset_control *stmmac_rst;
int clk_csr;
struct timer_list eee_ctrl_timer;
int lpi_irq;
@@ -120,8 +117,6 @@ struct stmmac_priv {
struct ptp_clock *ptp_clock;
struct ptp_clock_info ptp_clock_ops;
unsigned int default_addend;
- struct clk *clk_ptp_ref;
- unsigned int clk_ptp_rate;
u32 adv_ts;
int use_riwt;
int irq_wake;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 699ee1d..322e5c6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -712,7 +712,7 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
static u32 stmmac_usec2riwt(u32 usec, struct stmmac_priv *priv)
{
- unsigned long clk = clk_get_rate(priv->stmmac_clk);
+ unsigned long clk = clk_get_rate(priv->plat->stmmac_clk);
if (!clk)
return 0;
@@ -722,7 +722,7 @@ static u32 stmmac_usec2riwt(u32 usec, struct stmmac_priv *priv)
static u32 stmmac_riwt2usec(u32 riwt, struct stmmac_priv *priv)
{
- unsigned long clk = clk_get_rate(priv->stmmac_clk);
+ unsigned long clk = clk_get_rate(priv->plat->stmmac_clk);
if (!clk)
return 0;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index fa0b4de..02808e8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -158,7 +158,7 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
{
u32 clk_rate;
- clk_rate = clk_get_rate(priv->stmmac_clk);
+ clk_rate = clk_get_rate(priv->plat->stmmac_clk);
/* Platform provided default clk_csr would be assumed valid
* for all other cases except for the below mentioned ones.
@@ -607,7 +607,7 @@ static int stmmac_hwtstamp_ioctl(struct net_device *dev, struct ifreq *ifr)
/* program Sub Second Increment reg */
sec_inc = priv->hw->ptp->config_sub_second_increment(
- priv->ptpaddr, priv->clk_ptp_rate,
+ priv->ptpaddr, priv->plat->clk_ptp_rate,
priv->plat->has_gmac4);
temp = div_u64(1000000000ULL, sec_inc);
@@ -617,7 +617,7 @@ static int stmmac_hwtstamp_ioctl(struct net_device *dev, struct ifreq *ifr)
* where, freq_div_ratio = 1e9ns/sec_inc
*/
temp = (u64)(temp << 32);
- priv->default_addend = div_u64(temp, priv->clk_ptp_rate);
+ priv->default_addend = div_u64(temp, priv->plat->clk_ptp_rate);
priv->hw->ptp->config_addend(priv->ptpaddr,
priv->default_addend);
@@ -645,18 +645,6 @@ static int stmmac_init_ptp(struct stmmac_priv *priv)
if (!(priv->dma_cap.time_stamp || priv->dma_cap.atime_stamp))
return -EOPNOTSUPP;
- /* Fall-back to main clock in case of no PTP ref is passed */
- priv->clk_ptp_ref = devm_clk_get(priv->device, "clk_ptp_ref");
- if (IS_ERR(priv->clk_ptp_ref)) {
- priv->clk_ptp_rate = clk_get_rate(priv->stmmac_clk);
- priv->clk_ptp_ref = NULL;
- netdev_dbg(priv->dev, "PTP uses main clock\n");
- } else {
- clk_prepare_enable(priv->clk_ptp_ref);
- priv->clk_ptp_rate = clk_get_rate(priv->clk_ptp_ref);
- netdev_dbg(priv->dev, "PTP rate %d\n", priv->clk_ptp_rate);
- }
-
priv->adv_ts = 0;
/* Check if adv_ts can be enabled for dwmac 4.x core */
if (priv->plat->has_gmac4 && priv->dma_cap.atime_stamp)
@@ -683,8 +671,8 @@ static int stmmac_init_ptp(struct stmmac_priv *priv)
static void stmmac_release_ptp(struct stmmac_priv *priv)
{
- if (priv->clk_ptp_ref)
- clk_disable_unprepare(priv->clk_ptp_ref);
+ if (priv->plat->clk_ptp_ref)
+ clk_disable_unprepare(priv->plat->clk_ptp_ref);
stmmac_ptp_unregister(priv);
}
@@ -3278,44 +3266,8 @@ int stmmac_dvr_probe(struct device *device,
if ((phyaddr >= 0) && (phyaddr <= 31))
priv->plat->phy_addr = phyaddr;
- priv->stmmac_clk = devm_clk_get(priv->device, STMMAC_RESOURCE_NAME);
- if (IS_ERR(priv->stmmac_clk)) {
- netdev_warn(priv->dev, "%s: warning: cannot get CSR clock\n",
- __func__);
- /* If failed to obtain stmmac_clk and specific clk_csr value
- * is NOT passed from the platform, probe fail.
- */
- if (!priv->plat->clk_csr) {
- ret = PTR_ERR(priv->stmmac_clk);
- goto error_clk_get;
- } else {
- priv->stmmac_clk = NULL;
- }
- }
- clk_prepare_enable(priv->stmmac_clk);
-
- priv->pclk = devm_clk_get(priv->device, "pclk");
- if (IS_ERR(priv->pclk)) {
- if (PTR_ERR(priv->pclk) == -EPROBE_DEFER) {
- ret = -EPROBE_DEFER;
- goto error_pclk_get;
- }
- priv->pclk = NULL;
- }
- clk_prepare_enable(priv->pclk);
-
- priv->stmmac_rst = devm_reset_control_get(priv->device,
- STMMAC_RESOURCE_NAME);
- if (IS_ERR(priv->stmmac_rst)) {
- if (PTR_ERR(priv->stmmac_rst) == -EPROBE_DEFER) {
- ret = -EPROBE_DEFER;
- goto error_hw_init;
- }
- dev_info(priv->device, "no reset control found\n");
- priv->stmmac_rst = NULL;
- }
- if (priv->stmmac_rst)
- reset_control_deassert(priv->stmmac_rst);
+ if (priv->plat->stmmac_rst)
+ reset_control_deassert(priv->plat->stmmac_rst);
/* Init MAC and get the capabilities */
ret = stmmac_hw_init(priv);
@@ -3409,10 +3361,6 @@ int stmmac_dvr_probe(struct device *device,
error_mdio_register:
netif_napi_del(&priv->napi);
error_hw_init:
- clk_disable_unprepare(priv->pclk);
-error_pclk_get:
- clk_disable_unprepare(priv->stmmac_clk);
-error_clk_get:
free_netdev(ndev);
return ret;
@@ -3438,10 +3386,10 @@ int stmmac_dvr_remove(struct device *dev)
stmmac_set_mac(priv->ioaddr, false);
netif_carrier_off(ndev);
unregister_netdev(ndev);
- if (priv->stmmac_rst)
- reset_control_assert(priv->stmmac_rst);
- clk_disable_unprepare(priv->pclk);
- clk_disable_unprepare(priv->stmmac_clk);
+ if (priv->plat->stmmac_rst)
+ reset_control_assert(priv->plat->stmmac_rst);
+ clk_disable_unprepare(priv->plat->pclk);
+ clk_disable_unprepare(priv->plat->stmmac_clk);
if (priv->hw->pcs != STMMAC_PCS_RGMII &&
priv->hw->pcs != STMMAC_PCS_TBI &&
priv->hw->pcs != STMMAC_PCS_RTBI)
@@ -3490,8 +3438,8 @@ int stmmac_suspend(struct device *dev)
stmmac_set_mac(priv->ioaddr, false);
pinctrl_pm_select_sleep_state(priv->device);
/* Disable clock in case of PWM is off */
- clk_disable(priv->pclk);
- clk_disable(priv->stmmac_clk);
+ clk_disable(priv->plat->pclk);
+ clk_disable(priv->plat->stmmac_clk);
}
spin_unlock_irqrestore(&priv->lock, flags);
@@ -3531,8 +3479,8 @@ int stmmac_resume(struct device *dev)
} else {
pinctrl_pm_select_default_state(priv->device);
/* enable the clk prevously disabled */
- clk_enable(priv->stmmac_clk);
- clk_enable(priv->pclk);
+ clk_enable(priv->plat->stmmac_clk);
+ clk_enable(priv->plat->pclk);
/* reset the phy so that it's ready */
if (priv->mii)
stmmac_mdio_reset(priv->mii);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 78ccb50..b489ae4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -335,7 +335,54 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
plat->axi = stmmac_axi_setup(pdev);
+ /* clock setup */
+ plat->stmmac_clk = devm_clk_get(&pdev->dev,
+ STMMAC_RESOURCE_NAME);
+ if (IS_ERR(plat->stmmac_clk)) {
+ dev_warn(&pdev->dev, "Cannot get CSR clock\n");
+ plat->stmmac_clk = NULL;
+ }
+ clk_prepare_enable(plat->stmmac_clk);
+
+ plat->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(plat->pclk)) {
+ if (PTR_ERR(plat->pclk) == -EPROBE_DEFER)
+ goto error_pclk_get;
+
+ plat->pclk = NULL;
+ }
+ clk_prepare_enable(plat->pclk);
+
+ /* Fall-back to main clock in case of no PTP ref is passed */
+ plat->clk_ptp_ref = devm_clk_get(&pdev->dev, "clk_ptp_ref");
+ if (IS_ERR(plat->clk_ptp_ref)) {
+ plat->clk_ptp_rate = clk_get_rate(plat->stmmac_clk);
+ plat->clk_ptp_ref = NULL;
+ dev_warn(&pdev->dev, "PTP uses main clock\n");
+ } else {
+ clk_prepare_enable(plat->clk_ptp_ref);
+ plat->clk_ptp_rate = clk_get_rate(plat->clk_ptp_ref);
+ dev_info(&pdev->dev, "No reset control found\n");
+ }
+
+ plat->stmmac_rst = devm_reset_control_get(&pdev->dev,
+ STMMAC_RESOURCE_NAME);
+ if (IS_ERR(plat->stmmac_rst)) {
+ if (PTR_ERR(plat->stmmac_rst) == -EPROBE_DEFER)
+ goto error_hw_init;
+
+ dev_info(&pdev->dev, "no reset control found\n");
+ plat->stmmac_rst = NULL;
+ }
+
return plat;
+
+error_hw_init:
+ clk_disable_unprepare(plat->pclk);
+error_pclk_get:
+ clk_disable_unprepare(plat->stmmac_clk);
+
+ return ERR_PTR(-EPROBE_DEFER);
}
/**
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index e3cd758..d76033d6 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -138,6 +138,11 @@ struct plat_stmmacenet_data {
int (*init)(struct platform_device *pdev, void *priv);
void (*exit)(struct platform_device *pdev, void *priv);
void *bsp_priv;
+ struct clk *stmmac_clk;
+ struct clk *pclk;
+ struct clk *clk_ptp_ref;
+ unsigned int clk_ptp_rate;
+ struct reset_control *stmmac_rst;
struct stmmac_axi *axi;
int has_gmac4;
bool tso_en;
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v6 3/3] stmmac: adding new glue driver dwmac-dwc-qos-eth
2017-01-09 12:35 [PATCH v6 0/3] adding new glue driver dwmac-dwc-qos-eth Joao Pinto
2017-01-09 12:35 ` [PATCH v6 1/3] stmmac: adding DT parameter for LPI tx clock gating Joao Pinto
2017-01-09 12:35 ` [PATCH v6 2/3] stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure Joao Pinto
@ 2017-01-09 12:35 ` Joao Pinto
2017-01-09 19:54 ` [PATCH v6 0/3] " David Miller
3 siblings, 0 replies; 5+ messages in thread
From: Joao Pinto @ 2017-01-09 12:35 UTC (permalink / raw)
To: davem
Cc: lars.persson, niklass, swarren, treding, netdev, nathan.sullivan,
Joao Pinto
This patch adds a new glue driver called dwmac-dwc-qos-eth which
was based in the dwc_eth_qos as is. To assure retro-compatibility a slight
tweak was also added to stmmac_platform.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
---
changes v5 -> v6:
- rebased master branch to achieve clean patch
changes v4 -> v5:
- memset was not done properly
changes v3 -> v4:
- stmmac_res is now being initialized to 0
changes v2 -> v3:
- Nothing changed, just to keep up patch set version
changes v1 -> v2:
- WOL was not declared in the new glue driver
- clocks were switched and now fixed (apb_pclk and phy_ref_clk)
.../bindings/net/snps,dwc-qos-ethernet.txt | 3 +
drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
.../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 202 +++++++++++++++++++++
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 15 +-
5 files changed, 227 insertions(+), 3 deletions(-)
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c
diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
index d93f71c..21d27aa 100644
--- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
+++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
@@ -1,5 +1,8 @@
* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+This binding is deprecated, but it continues to be supported, but new
+features should be preferably added to the stmmac binding document.
+
This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service)
IP block. The IP supports multiple options for bus type, clocking and reset
structure, and feature list. Consequently, a number of properties and list
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index ab66248..99594e3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -29,6 +29,15 @@ config STMMAC_PLATFORM
if STMMAC_PLATFORM
+config DWMAC_DWC_QOS_ETH
+ tristate "Support for snps,dwc-qos-ethernet.txt DT binding."
+ select PHYLIB
+ select CRC32
+ select MII
+ depends on OF && HAS_DMA
+ help
+ Support for chips using the snps,dwc-qos-ethernet.txt DT binding.
+
config DWMAC_GENERIC
tristate "Generic driver for DWMAC"
default STMMAC_PLATFORM
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 8f83a86..700c603 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o
obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o
obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
+obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
stmmac-platform-objs:= stmmac_platform.o
dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c
new file mode 100644
index 0000000..1a3fa3d
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c
@@ -0,0 +1,202 @@
+/*
+ * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver
+ *
+ * Copyright (C) 2016 Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/ethtool.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of_net.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+
+#include "stmmac_platform.h"
+
+static int dwc_eth_dwmac_config_dt(struct platform_device *pdev,
+ struct plat_stmmacenet_data *plat_dat)
+{
+ struct device_node *np = pdev->dev.of_node;
+ u32 burst_map = 0;
+ u32 bit_index = 0;
+ u32 a_index = 0;
+
+ if (!plat_dat->axi) {
+ plat_dat->axi = kzalloc(sizeof(struct stmmac_axi), GFP_KERNEL);
+
+ if (!plat_dat->axi)
+ return -ENOMEM;
+ }
+
+ plat_dat->axi->axi_lpi_en = of_property_read_bool(np, "snps,en-lpi");
+ if (of_property_read_u32(np, "snps,write-requests",
+ &plat_dat->axi->axi_wr_osr_lmt)) {
+ /**
+ * Since the register has a reset value of 1, if property
+ * is missing, default to 1.
+ */
+ plat_dat->axi->axi_wr_osr_lmt = 1;
+ } else {
+ /**
+ * If property exists, to keep the behavior from dwc_eth_qos,
+ * subtract one after parsing.
+ */
+ plat_dat->axi->axi_wr_osr_lmt--;
+ }
+
+ if (of_property_read_u32(np, "read,read-requests",
+ &plat_dat->axi->axi_rd_osr_lmt)) {
+ /**
+ * Since the register has a reset value of 1, if property
+ * is missing, default to 1.
+ */
+ plat_dat->axi->axi_rd_osr_lmt = 1;
+ } else {
+ /**
+ * If property exists, to keep the behavior from dwc_eth_qos,
+ * subtract one after parsing.
+ */
+ plat_dat->axi->axi_rd_osr_lmt--;
+ }
+ of_property_read_u32(np, "snps,burst-map", &burst_map);
+
+ /* converts burst-map bitmask to burst array */
+ for (bit_index = 0; bit_index < 7; bit_index++) {
+ if (burst_map & (1 << bit_index)) {
+ switch (bit_index) {
+ case 0:
+ plat_dat->axi->axi_blen[a_index] = 4; break;
+ case 1:
+ plat_dat->axi->axi_blen[a_index] = 8; break;
+ case 2:
+ plat_dat->axi->axi_blen[a_index] = 16; break;
+ case 3:
+ plat_dat->axi->axi_blen[a_index] = 32; break;
+ case 4:
+ plat_dat->axi->axi_blen[a_index] = 64; break;
+ case 5:
+ plat_dat->axi->axi_blen[a_index] = 128; break;
+ case 6:
+ plat_dat->axi->axi_blen[a_index] = 256; break;
+ default:
+ break;
+ }
+ a_index++;
+ }
+ }
+
+ /* dwc-qos needs GMAC4, AAL, TSO and PMT */
+ plat_dat->has_gmac4 = 1;
+ plat_dat->dma_cfg->aal = 1;
+ plat_dat->tso_en = 1;
+ plat_dat->pmt = 1;
+
+ return 0;
+}
+
+static int dwc_eth_dwmac_probe(struct platform_device *pdev)
+{
+ struct plat_stmmacenet_data *plat_dat;
+ struct stmmac_resources stmmac_res;
+ struct resource *res;
+ int ret;
+
+ memset(&stmmac_res, 0, sizeof(struct stmmac_resources));
+
+ /**
+ * Since stmmac_platform supports name IRQ only, basic platform
+ * resource initialization is done in the glue logic.
+ */
+ stmmac_res.irq = platform_get_irq(pdev, 0);
+ if (stmmac_res.irq < 0) {
+ if (stmmac_res.irq != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "IRQ configuration information not found\n");
+
+ return stmmac_res.irq;
+ }
+ stmmac_res.wol_irq = stmmac_res.irq;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(stmmac_res.addr))
+ return PTR_ERR(stmmac_res.addr);
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
+
+ plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "apb_pclk");
+ if (IS_ERR(plat_dat->stmmac_clk)) {
+ dev_err(&pdev->dev, "apb_pclk clock not found.\n");
+ ret = PTR_ERR(plat_dat->stmmac_clk);
+ plat_dat->stmmac_clk = NULL;
+ goto err_remove_config_dt;
+ }
+ clk_prepare_enable(plat_dat->stmmac_clk);
+
+ plat_dat->pclk = devm_clk_get(&pdev->dev, "phy_ref_clk");
+ if (IS_ERR(plat_dat->pclk)) {
+ dev_err(&pdev->dev, "phy_ref_clk clock not found.\n");
+ ret = PTR_ERR(plat_dat->pclk);
+ plat_dat->pclk = NULL;
+ goto err_out_clk_dis_phy;
+ }
+ clk_prepare_enable(plat_dat->pclk);
+
+ ret = dwc_eth_dwmac_config_dt(pdev, plat_dat);
+ if (ret)
+ goto err_out_clk_dis_aper;
+
+ ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+ if (ret)
+ goto err_out_clk_dis_aper;
+
+ return 0;
+
+err_out_clk_dis_aper:
+ clk_disable_unprepare(plat_dat->pclk);
+err_out_clk_dis_phy:
+ clk_disable_unprepare(plat_dat->stmmac_clk);
+err_remove_config_dt:
+ stmmac_remove_config_dt(pdev, plat_dat);
+
+ return ret;
+}
+
+static int dwc_eth_dwmac_remove(struct platform_device *pdev)
+{
+ return stmmac_pltfr_remove(pdev);
+}
+
+static const struct of_device_id dwc_eth_dwmac_match[] = {
+ { .compatible = "snps,dwc-qos-ethernet-4.10", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match);
+
+static struct platform_driver dwc_eth_dwmac_driver = {
+ .probe = dwc_eth_dwmac_probe,
+ .remove = dwc_eth_dwmac_remove,
+ .driver = {
+ .name = "dwc-eth-dwmac",
+ .of_match_table = dwc_eth_dwmac_match,
+ },
+};
+module_platform_driver(dwc_eth_dwmac_driver);
+
+MODULE_AUTHOR("Joao Pinto <jpinto@synopsys.com>");
+MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index b489ae4..ac32f9e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -180,10 +180,19 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
mdio = false;
}
- /* If snps,dwmac-mdio is passed from DT, always register the MDIO */
- for_each_child_of_node(np, plat->mdio_node) {
- if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio"))
+ /* exception for dwmac-dwc-qos-eth glue logic */
+ if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) {
+ plat->mdio_node = of_get_child_by_name(np, "mdio");
+ } else {
+ /**
+ * If snps,dwmac-mdio is passed from DT, always register
+ * the MDIO
+ */
+ for_each_child_of_node(np, plat->mdio_node) {
+ if (of_device_is_compatible(plat->mdio_node,
+ "snps,dwmac-mdio"))
break;
+ }
}
if (plat->mdio_node) {
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH v6 0/3] adding new glue driver dwmac-dwc-qos-eth
2017-01-09 12:35 [PATCH v6 0/3] adding new glue driver dwmac-dwc-qos-eth Joao Pinto
` (2 preceding siblings ...)
2017-01-09 12:35 ` [PATCH v6 3/3] stmmac: adding new glue driver dwmac-dwc-qos-eth Joao Pinto
@ 2017-01-09 19:54 ` David Miller
3 siblings, 0 replies; 5+ messages in thread
From: David Miller @ 2017-01-09 19:54 UTC (permalink / raw)
To: Joao.Pinto
Cc: lars.persson, niklass, swarren, treding, netdev, nathan.sullivan
From: Joao Pinto <Joao.Pinto@synopsys.com>
Date: Mon, 9 Jan 2017 12:35:07 +0000
> This patch set contains the porting of the synopsys/dwc_eth_qos.c driver
> to the stmmac structure. This operation resulted in the creation of a new
> platform glue driver called dwmac-dwc-qos-eth which was based in the
> dwc_eth_qos as is.
>
> dwmac-dwc-qos-eth inherited dwc_eth_qos DT bindings, to assure that current
> and old users can continue to use it as before. We can see this driver as
> being deprecated, since all new development will be done in stmmac.
>
> Please check each patch for implementation details.
Series applied, thanks Joao.
^ permalink raw reply [flat|nested] 5+ messages in thread