netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Jose Abreu <Jose.Abreu@synopsys.com>
To: netdev@vger.kernel.org
Cc: Joao Pinto <Joao.Pinto@synopsys.com>,
	Jose Abreu <Jose.Abreu@synopsys.com>,
	Giuseppe Cavallaro <peppe.cavallaro@st.com>,
	Alexandre Torgue <alexandre.torgue@st.com>,
	Jose Abreu <Jose.Abreu@synopsys.com>,
	"David S. Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Russell King <linux@armlinux.org.uk>,
	Andrew Lunn <andrew@lunn.ch>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	linux-stm32@st-md-mailman.stormreply.com,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH net-next 0/8] net: Add support for Synopsys DesignWare XPCS
Date: Mon,  9 Mar 2020 09:36:19 +0100	[thread overview]
Message-ID: <cover.1583742615.git.Jose.Abreu@synopsys.com> (raw)

This adds support for Synopsys DesignWare XPCS in net subsystem and
integrates it into stmmac.

At 1/8, we start by removing the limitation of stmmac selftests that needed
a PHY to pass all the tests.

Then at 2/8 we use some helpers in stmmac so that some code can be
simplified.

At 3/8, we fallback to dev_fwnode() so that PCI based setups wich may
not have CONFIG_OF can still use FW node.

At 4/8, we adapt stmmac to the new PHYLINK changes as suggested by Russell
King.

We proceed by doing changes in PHYLINK in order to support XPCS: At 5/8 we
add some missing speeds that USXGMII supports and at 6/8 we check if
Autoneg is supported after initial parameters are validated.

Support for XPCS is finally introduced at 7/8, along with the usage of it
in stmmac driver at 8/8.

---
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---

Jose Abreu (8):
  net: stmmac: selftests: Do not fail if PHY is not attached
  net: stmmac: Switch to linkmode_and()/linkmode_andnot()
  net: stmmac: Fallback to dev_fwnode() if needed
  net: stmmac: Use resolved link config in mac_link_up()
  net: phylink: Add missing Backplane speeds
  net: phylink: Test if MAC/PCS support Autoneg
  net: phy: Add Synopsys DesignWare XPCS MDIO module
  net: stmmac: Integrate it with DesignWare XPCS

 MAINTAINERS                                        |   7 +
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |   1 +
 drivers/net/ethernet/stmicro/stmmac/common.h       |   3 +
 drivers/net/ethernet/stmicro/stmmac/hwif.h         |  12 +
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  96 ++--
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c  |  27 +
 .../net/ethernet/stmicro/stmmac/stmmac_selftests.c |   2 +-
 drivers/net/phy/Kconfig                            |   6 +
 drivers/net/phy/Makefile                           |   1 +
 drivers/net/phy/mdio-xpcs.c                        | 612 +++++++++++++++++++++
 drivers/net/phy/phylink.c                          |   5 +
 include/linux/mdio-xpcs.h                          |  41 ++
 include/linux/stmmac.h                             |   1 +
 13 files changed, 771 insertions(+), 43 deletions(-)
 create mode 100644 drivers/net/phy/mdio-xpcs.c
 create mode 100644 include/linux/mdio-xpcs.h

-- 
2.7.4


             reply	other threads:[~2020-03-09  8:37 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-03-09  8:36 Jose Abreu [this message]
2020-03-09  8:36 ` [PATCH net-next 1/8] net: stmmac: selftests: Do not fail if PHY is not attached Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 2/8] net: stmmac: Switch to linkmode_and()/linkmode_andnot() Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 3/8] net: stmmac: Fallback to dev_fwnode() if needed Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 4/8] net: stmmac: Use resolved link config in mac_link_up() Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 5/8] net: phylink: Add missing Backplane speeds Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 6/8] net: phylink: Test if MAC/PCS support Autoneg Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 7/8] net: phy: Add Synopsys DesignWare XPCS MDIO module Jose Abreu
2020-06-05 17:10   ` Russell King - ARM Linux admin
2020-06-09 14:24     ` Jose Abreu
2020-03-09  8:36 ` [PATCH net-next 8/8] net: stmmac: Integrate it with DesignWare XPCS Jose Abreu
2020-03-10  3:13 ` [PATCH net-next 0/8] net: Add support for Synopsys " David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=cover.1583742615.git.Jose.Abreu@synopsys.com \
    --to=jose.abreu@synopsys.com \
    --cc=Joao.Pinto@synopsys.com \
    --cc=alexandre.torgue@st.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=f.fainelli@gmail.com \
    --cc=hkallweit1@gmail.com \
    --cc=kuba@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=linux@armlinux.org.uk \
    --cc=mcoquelin.stm32@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=peppe.cavallaro@st.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).