[PATCH net-next v4 0/2] net: dsa: mxl862xx: add support for bridge offloading

[PATCH net-next v4 0/2] net: dsa: mxl862xx: add support for bridge offloading

[Daniel Golle]

As a next step to complete the mxl862xx DSA driver, add support for
offloading forwarding between bridged ports to the switch hardware.

This works pretty much without any big surprises, apart from two
subtleties:
 * per-port control over flooding behavior has to be implemented by
   (ab)using a 0-rate QoS meters as stopper in lack of any better
   option.
 * STP state transition unconditionally enables learning on a port
   even if it was previously explicitely disabled (a firmware bug)

Note that as the driver is still lacking all VLAN features (which
are going to be added next), at this point some of the
bridge_vlan_aware.sh tests are failing after applying this series.

This is expected and cannot be avoided without implementing
port_vlan_filtering + port_vlan_add/del. And adding both bridge and
VLAN offloading at the same time would be too much for anyone to
review, so VLAN support is going to be submitted in a follow-up
series immediately after this series has been accepted.

All other relevant selftests (including bridge_vlan_unaware.sh) are
still passing.

Changes since v3:
 * add missing cpu_to_le32 in mxl862xx_bridge_config_fwd()
 * use little-endian 32-bit type for (unused) age_timer API field
 * better comment in port_set_host_flood() documenting architectural
   limitation
 * fix typo in comment "matche" should be "matches"
 * few whitespace fixes

Changes since v2:
 * refactor .port_bridge_join and .port_bridge_leave as requested
   by Vladimir Oltean
 * include linux/etherdevice.h which was missing and causing build
   to fail (it accidentally slipped into a follow-up patch)
 * remove left-over manual reset of learning state for port leaving
   bridge
 * remove unnecessary call to mxl862xx_port_fast_age() for port
   leaving bridge
 * add kernel-doc comments in mxl862xx.h instead of sporadic inline
   comments covering only some of the struct members
 * some other minor cosmetics (linebreaks, whitespace) here and there

Changes since v1:
 * don't set dsa_default_offload_fwd_mark() on link-local frames
 * fix kernel-doc comments in API header
 * use bitfield helpers for compound tci field in fdb API
 * add missing endian conversion for mxl862xx_stp_port_cfg.port_state
   as well as mxl862xx_mac_table_read.tci (spotted by AI review)
 * drop manually resetting port learning state on bridge<->standalone
   transitions, DSA framework takes care of that
 * don't abort updating bridge ports on error, return error at the end
 * report error in mxl862xx_port_bridge_leave()
 * create mxl862xx_get_fid() helper and use it in
   mxl862xx_port_fdb_add() and mxl862xx_port_fdb_del()
 * propagete error of callback function in mxl862xx_port_fdb_dump()
 * manually mxl862xx_port_fast_age() in mxl862xx_port_stp_state_set()
   to avoid FDB poisoning due to race condition

Daniel Golle (2):
  dsa: tag_mxl862xx: set dsa_default_offload_fwd_mark()
  net: dsa: mxl862xx: implement bridge offloading

 drivers/net/dsa/mxl862xx/mxl862xx-api.h | 180 +++++++-
 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h |  19 +-
 drivers/net/dsa/mxl862xx/mxl862xx.c     | 588 ++++++++++++++++++++++--
 drivers/net/dsa/mxl862xx/mxl862xx.h     |  52 +++
 net/dsa/tag_mxl862xx.c                  |   3 +
 5 files changed, 808 insertions(+), 34 deletions(-)

-- 
2.53.0

[PATCH net-next v4 1/2] dsa: tag_mxl862xx: set dsa_default_offload_fwd_mark()

[Daniel Golle]

The MxL862xx offloads bridge forwarding in hardware, so set
dsa_default_offload_fwd_mark() to avoid duplicate forwarding of
packets of (eg. flooded) frames arriving at the CPU port.

Link-local frames are directly trapped to the CPU port only, so don't
set dsa_default_offload_fwd_mark() on those.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
v4: no changes
v3: no changes
v2: don't set dsa_default_offload_fwd_mark() on link-local frames

 net/dsa/tag_mxl862xx.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/dsa/tag_mxl862xx.c b/net/dsa/tag_mxl862xx.c
index 01f2158682718..ec949d44fc91c 100644
--- a/net/dsa/tag_mxl862xx.c
+++ b/net/dsa/tag_mxl862xx.c
@@ -92,6 +92,9 @@ static struct sk_buff *mxl862_tag_rcv(struct sk_buff *skb,
 	skb_pull_rcsum(skb, MXL862_HEADER_LEN);
 	dsa_strip_etype_header(skb, MXL862_HEADER_LEN);
 
+	if (likely(!is_link_local_ether_addr(eth_hdr(skb)->h_dest)))
+		dsa_default_offload_fwd_mark(skb);
+
 	return skb;
 }
 
-- 
2.53.0

[PATCH net-next v4 2/2] net: dsa: mxl862xx: implement bridge offloading

[Daniel Golle]

Add support for bridge offloading on the mxl862xx DSA driver.

Implement joining and leaving bridges as well as add, delete and dump
operations on isolated FDBs and setting a port's STP state.

The switch supports a maximum of 63 bridges, however, up to 12 may
be used as "single-port bridges" to isolate standalone ports.
Allowing up to 48 bridges to be offloaded seems more than enough on
that hardware, hence that is set as max_num_bridges.

A total of 128 bridge ports are supported in the bridge portmap, and
virtual bridge ports have to be used eg. for link-aggregation, hence
potentially exceeding the number of hardware ports.

As there are now more users of the BRIDGEPORT_CONFIG_SET API and the
state of each port is cached locally, introduce a helper function
mxl862xx_set_bridge_port(struct dsa_switch *ds, int port) which is
then also be used to replace the direct calls to the API in
mxl862xx_setup_cpu_bridge() and mxl862xx_add_single_port_bridge().

Note that there is no convenient way to control flooding on per-port
level, so the driver is using a 0-rate QoS meter setup as a stopper in
lack of any better option. This works, but allows a single 64-byte
packet to pass once after reset. While this limitation doesn't seem to
be a problem in practice, it has the effect that the
bridge_vlan_unaware.sh selftest only passes the FDB test the 2nd time
the test is run after boot (and any subsequent time after that, of
course).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
v4:
 * add missing cpu_to_le32 in mxl862xx_bridge_config_fwd()
 * use little-endian 32-bit type for (unused) age_timer API field
 * better comment in port_set_host_flood() documenting architectural
   limitation
 * fix typo in comment "matche" should be "matches"
 * few whitespace fixes

v3:
 * refactor .port_bridge_join and .port_bridge_leave as requested
   by Vladimir Oltean
 * include linux/etherdevice.h which was missing and causing build
   to fail (it accidentally slipped into a follow-up patch)
 * remove left-over manual reset of learning state for port leaving
   bridge
 * remove unnecessary call to mxl862xx_port_fast_age() for port
   leaving bridge
 * add kernel-doc comments in mxl862xx.h instead of sporadic inline
   comments covering only some of the struct members
 * some other minor cosmetics (linebreaks, whitespace) here and there

v2:
 * fix kernel-doc comments in API header
 * use bitfield helpers for compound tci field in fdb API
 * add missing endian conversion for mxl862xx_stp_port_cfg.port_state
   as well as mxl862xx_mac_table_read.tci (spotted by AI review)
 * drop manually resetting port learning state on bridge<->standalone
   transitions, DSA framework takes care of that
 * don't abort updating bridge ports on error, return error at the end
 * report error in mxl862xx_port_bridge_leave()
 * create mxl862xx_get_fid() helper and use it in
   mxl862xx_port_fdb_add() and mxl862xx_port_fdb_del()
 * propagete error of callback function in mxl862xx_port_fdb_dump()
 * manually mxl862xx_port_fast_age() in mxl862xx_port_stp_state_set()
   to avoid FDB poisoning due to race condition

 drivers/net/dsa/mxl862xx/mxl862xx-api.h | 180 +++++++-
 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h |  19 +-
 drivers/net/dsa/mxl862xx/mxl862xx.c     | 588 ++++++++++++++++++++++--
 drivers/net/dsa/mxl862xx/mxl862xx.h     |  52 +++
 4 files changed, 805 insertions(+), 34 deletions(-)

diff --git a/drivers/net/dsa/mxl862xx/mxl862xx-api.h b/drivers/net/dsa/mxl862xx/mxl862xx-api.h
index a9f599dbca25b..485f1b472431f 100644
--- a/drivers/net/dsa/mxl862xx/mxl862xx-api.h
+++ b/drivers/net/dsa/mxl862xx/mxl862xx-api.h
@@ -3,6 +3,7 @@
 #ifndef __MXL862XX_API_H
 #define __MXL862XX_API_H
 
+#include <linux/bits.h>
 #include <linux/if_ether.h>
 
 /**
@@ -34,6 +35,123 @@ struct mxl862xx_register_mod {
 	__le16 mask;
 } __packed;
 
+/**
+ * enum mxl862xx_mac_table_filter - Source/Destination MAC address filtering
+ *
+ * @MXL862XX_MAC_FILTER_NONE: no filter
+ * @MXL862XX_MAC_FILTER_SRC: source address filter
+ * @MXL862XX_MAC_FILTER_DEST: destination address filter
+ * @MXL862XX_MAC_FILTER_BOTH: both source and destination filter
+ */
+enum mxl862xx_mac_table_filter {
+	MXL862XX_MAC_FILTER_NONE = 0,
+	MXL862XX_MAC_FILTER_SRC = BIT(0),
+	MXL862XX_MAC_FILTER_DEST = BIT(1),
+	MXL862XX_MAC_FILTER_BOTH = BIT(0) | BIT(1),
+};
+
+#define MXL862XX_TCI_VLAN_ID		GENMASK(11, 0)
+#define MXL862XX_TCI_VLAN_CFI_DEI	BIT(12)
+#define MXL862XX_TCI_VLAN_PRI		GENMASK(15, 13)
+
+/**
+ * struct mxl862xx_mac_table_add - MAC Table Entry to be added
+ * @fid: Filtering Identifier (FID) (not supported by all switches)
+ * @port_id: Ethernet Port number
+ * @port_map: Bridge Port Map
+ * @sub_if_id: Sub-Interface Identifier Destination
+ * @age_timer: Aging Time in seconds
+ * @vlan_id: STAG VLAN Id
+ * @static_entry: Static Entry (value will be aged out if not set to static)
+ * @traffic_class: Egress queue traffic class
+ * @mac: MAC Address to add to the table
+ * @filter_flag: See &enum mxl862xx_mac_table_filter
+ * @igmp_controlled: Packet is marked as IGMP controlled if destination MAC
+ *                   address matches MAC in this entry
+ * @associated_mac: Associated Mac address
+ * @tci: TCI for B-Step
+ *	Bit [0:11] - VLAN ID
+ *	Bit [12] - VLAN CFI/DEI
+ *	Bit [13:15] - VLAN PRI
+ */
+struct mxl862xx_mac_table_add {
+	__le16 fid;
+	__le32 port_id;
+	__le16 port_map[8];
+	__le16 sub_if_id;
+	__le32 age_timer;
+	__le16 vlan_id;
+	u8 static_entry;
+	u8 traffic_class;
+	u8 mac[ETH_ALEN];
+	u8 filter_flag;
+	u8 igmp_controlled;
+	u8 associated_mac[ETH_ALEN];
+	__le16 tci;
+} __packed;
+
+/**
+ * struct mxl862xx_mac_table_remove - MAC Table Entry to be removed
+ * @fid: Filtering Identifier (FID)
+ * @mac: MAC Address to be removed from the table.
+ * @filter_flag: See &enum mxl862xx_mac_table_filter
+ * @tci: TCI for B-Step
+ *	Bit [0:11] - VLAN ID
+ *	Bit [12] - VLAN CFI/DEI
+ *	Bit [13:15] - VLAN PRI
+ */
+struct mxl862xx_mac_table_remove {
+	__le16 fid;
+	u8 mac[ETH_ALEN];
+	u8 filter_flag;
+	__le16 tci;
+} __packed;
+
+/**
+ * struct mxl862xx_mac_table_read - MAC Table Entry to be read
+ * @initial: Restart the get operation from the beginning of the table
+ * @last: Indicates that the read operation returned last entry
+ * @fid: Get the MAC table entry belonging to the given Filtering Identifier
+ * @port_id: The Bridge Port ID
+ * @port_map: Bridge Port Map
+ * @age_timer: Aging Time
+ * @vlan_id: STAG VLAN Id
+ * @static_entry: Indicates if this is a Static Entry
+ * @sub_if_id: Sub-Interface Identifier Destination
+ * @mac: MAC Address. Filled out by the switch API implementation.
+ * @filter_flag: See &enum mxl862xx_mac_table_filter
+ * @igmp_controlled: Packet is marked as IGMP controlled if destination MAC
+ *                   address matches the MAC in this entry
+ * @entry_changed: Indicate if the Entry has Changed
+ * @associated_mac: Associated MAC address
+ * @hit_status: MAC Table Hit Status Update
+ * @tci: TCI for B-Step
+ *	Bit [0:11] - VLAN ID
+ *	Bit [12] - VLAN CFI/DEI
+ *	Bit [13:15] - VLAN PRI
+ * @first_bridge_port_id: The port this MAC address has first been learned.
+ *                        This is used for loop detection.
+ */
+struct mxl862xx_mac_table_read {
+	u8 initial;
+	u8 last;
+	__le16 fid;
+	__le32 port_id;
+	__le16 port_map[8];
+	__le32 age_timer;
+	__le16 vlan_id;
+	u8 static_entry;
+	__le16 sub_if_id;
+	u8 mac[ETH_ALEN];
+	u8 filter_flag;
+	u8 igmp_controlled;
+	u8 entry_changed;
+	u8 associated_mac[ETH_ALEN];
+	u8 hit_status;
+	__le16 tci;
+	__le16 first_bridge_port_id;
+} __packed;
+
 /**
  * enum mxl862xx_mac_clear_type - MAC table clear type
  * @MXL862XX_MAC_CLEAR_PHY_PORT: clear dynamic entries based on port_id
@@ -138,6 +256,40 @@ enum mxl862xx_bridge_port_egress_meter {
 	MXL862XX_BRIDGE_PORT_EGRESS_METER_MAX,
 };
 
+/**
+ * struct mxl862xx_qos_meter_cfg - Rate meter configuration
+ * @enable: Enable/disable meter
+ * @meter_id: Meter ID (assigned by firmware on alloc)
+ * @meter_name: Meter name string
+ * @meter_type: Meter algorithm type (srTCM = 0, trTCM = 1)
+ * @cbs: Committed Burst Size (in bytes)
+ * @res1: Reserved
+ * @ebs: Excess Burst Size (in bytes)
+ * @res2: Reserved
+ * @rate: Committed Information Rate (in kbit/s)
+ * @pi_rate: Peak Information Rate (in kbit/s)
+ * @colour_blind_mode: Colour-blind mode enable
+ * @pkt_mode: Packet mode enable
+ * @local_overhd: Local overhead accounting enable
+ * @local_overhd_val: Local overhead accounting value
+ */
+struct mxl862xx_qos_meter_cfg {
+	u8 enable;
+	__le16 meter_id;
+	char meter_name[32];
+	__le32 meter_type;
+	__le32 cbs;
+	__le32 res1;
+	__le32 ebs;
+	__le32 res2;
+	__le32 rate;
+	__le32 pi_rate;
+	u8 colour_blind_mode;
+	u8 pkt_mode;
+	u8 local_overhd;
+	__le16 local_overhd_val;
+} __packed;
+
 /**
  * enum mxl862xx_bridge_forward_mode - Bridge forwarding type of packet
  * @MXL862XX_BRIDGE_FORWARD_FLOOD: Packet is flooded to port members of
@@ -456,7 +608,7 @@ struct mxl862xx_pmapper {
  */
 struct mxl862xx_bridge_port_config {
 	__le16 bridge_port_id;
-	__le32 mask; /* enum mxl862xx_bridge_port_config_mask  */
+	__le32 mask; /* enum mxl862xx_bridge_port_config_mask */
 	__le16 bridge_id;
 	u8 ingress_extended_vlan_enable;
 	__le16 ingress_extended_vlan_block_id;
@@ -658,6 +810,32 @@ struct mxl862xx_ctp_port_assignment {
 	__le16 bridge_port_id;
 } __packed;
 
+/**
+ * enum mxl862xx_stp_port_state - Spanning Tree Protocol port states
+ * @MXL862XX_STP_PORT_STATE_FORWARD: Forwarding state
+ * @MXL862XX_STP_PORT_STATE_DISABLE: Disabled/Discarding state
+ * @MXL862XX_STP_PORT_STATE_LEARNING: Learning state
+ * @MXL862XX_STP_PORT_STATE_BLOCKING: Blocking/Listening
+ */
+enum mxl862xx_stp_port_state {
+	MXL862XX_STP_PORT_STATE_FORWARD = 0,
+	MXL862XX_STP_PORT_STATE_DISABLE,
+	MXL862XX_STP_PORT_STATE_LEARNING,
+	MXL862XX_STP_PORT_STATE_BLOCKING,
+};
+
+/**
+ * struct mxl862xx_stp_port_cfg - Configures the Spanning Tree Protocol state
+ * @port_id: Port number
+ * @fid: Filtering Identifier (FID)
+ * @port_state: See &enum mxl862xx_stp_port_state
+ */
+struct mxl862xx_stp_port_cfg {
+	__le16 port_id;
+	__le16 fid;
+	__le32 port_state; /* enum mxl862xx_stp_port_state */
+} __packed;
+
 /**
  * struct mxl862xx_sys_fw_image_version - Firmware version information
  * @iv_major: firmware major version
diff --git a/drivers/net/dsa/mxl862xx/mxl862xx-cmd.h b/drivers/net/dsa/mxl862xx/mxl862xx-cmd.h
index f6852ade64e7c..43d04c019b50c 100644
--- a/drivers/net/dsa/mxl862xx/mxl862xx-cmd.h
+++ b/drivers/net/dsa/mxl862xx/mxl862xx-cmd.h
@@ -15,12 +15,15 @@
 #define MXL862XX_BRDG_MAGIC		0x300
 #define MXL862XX_BRDGPORT_MAGIC		0x400
 #define MXL862XX_CTP_MAGIC		0x500
+#define MXL862XX_QOS_MAGIC		0x600
 #define MXL862XX_SWMAC_MAGIC		0xa00
+#define MXL862XX_STP_MAGIC		0xf00
 #define MXL862XX_SS_MAGIC		0x1600
 #define GPY_GPY2XX_MAGIC		0x1800
 #define SYS_MISC_MAGIC			0x1900
 
 #define MXL862XX_COMMON_CFGGET		(MXL862XX_COMMON_MAGIC + 0x9)
+#define MXL862XX_COMMON_CFGSET		(MXL862XX_COMMON_MAGIC + 0xa)
 #define MXL862XX_COMMON_REGISTERMOD	(MXL862XX_COMMON_MAGIC + 0x11)
 
 #define MXL862XX_BRIDGE_ALLOC		(MXL862XX_BRDG_MAGIC + 0x1)
@@ -35,14 +38,22 @@
 
 #define MXL862XX_CTP_PORTASSIGNMENTSET	(MXL862XX_CTP_MAGIC + 0x3)
 
+#define MXL862XX_QOS_METERCFGSET	(MXL862XX_QOS_MAGIC + 0x2)
+#define MXL862XX_QOS_METERALLOC		(MXL862XX_QOS_MAGIC + 0x2a)
+
+#define MXL862XX_MAC_TABLEENTRYADD	(MXL862XX_SWMAC_MAGIC + 0x2)
+#define MXL862XX_MAC_TABLEENTRYREAD	(MXL862XX_SWMAC_MAGIC + 0x3)
+#define MXL862XX_MAC_TABLEENTRYREMOVE	(MXL862XX_SWMAC_MAGIC + 0x5)
 #define MXL862XX_MAC_TABLECLEARCOND	(MXL862XX_SWMAC_MAGIC + 0x8)
 
-#define MXL862XX_SS_SPTAG_SET		(MXL862XX_SS_MAGIC + 0x02)
+#define MXL862XX_SS_SPTAG_SET		(MXL862XX_SS_MAGIC + 0x2)
+
+#define MXL862XX_STP_PORTCFGSET		(MXL862XX_STP_MAGIC + 0x2)
 
-#define INT_GPHY_READ			(GPY_GPY2XX_MAGIC + 0x01)
-#define INT_GPHY_WRITE			(GPY_GPY2XX_MAGIC + 0x02)
+#define INT_GPHY_READ			(GPY_GPY2XX_MAGIC + 0x1)
+#define INT_GPHY_WRITE			(GPY_GPY2XX_MAGIC + 0x2)
 
-#define SYS_MISC_FW_VERSION		(SYS_MISC_MAGIC + 0x02)
+#define SYS_MISC_FW_VERSION		(SYS_MISC_MAGIC + 0x2)
 
 #define MMD_API_MAXIMUM_ID		0x7fff
 
diff --git a/drivers/net/dsa/mxl862xx/mxl862xx.c b/drivers/net/dsa/mxl862xx/mxl862xx.c
index 8281c749967af..84e5625a2924c 100644
--- a/drivers/net/dsa/mxl862xx/mxl862xx.c
+++ b/drivers/net/dsa/mxl862xx/mxl862xx.c
@@ -7,8 +7,11 @@
  * Copyright (C) 2025 Daniel Golle <daniel@makrotopia.org>
  */
 
-#include <linux/module.h>
+#include <linux/bitfield.h>
 #include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/of_mdio.h>
 #include <linux/phy.h>
@@ -36,6 +39,13 @@
 #define MXL862XX_READY_TIMEOUT_MS	10000
 #define MXL862XX_READY_POLL_MS		100
 
+static const int mxl862xx_flood_meters[] = {
+	MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_UC,
+	MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_IP,
+	MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_NON_IP,
+	MXL862XX_BRIDGE_PORT_EGRESS_METER_BROADCAST,
+};
+
 static enum dsa_tag_protocol mxl862xx_get_tag_protocol(struct dsa_switch *ds,
 						       int port,
 						       enum dsa_tag_protocol m)
@@ -169,6 +179,66 @@ static int mxl862xx_setup_mdio(struct dsa_switch *ds)
 	return ret;
 }
 
+static int mxl862xx_bridge_config_fwd(struct dsa_switch *ds, u16 bridge_id,
+				      bool ucast_flood, bool mcast_flood,
+				      bool bcast_flood)
+{
+	struct mxl862xx_bridge_config bridge_config = { };
+	struct mxl862xx_priv *priv = ds->priv;
+	int ret;
+
+	bridge_config.mask = cpu_to_le32(MXL862XX_BRIDGE_CONFIG_MASK_FORWARDING_MODE);
+	bridge_config.bridge_id = cpu_to_le16(bridge_id);
+
+	bridge_config.forward_unknown_unicast = cpu_to_le32(ucast_flood ?
+		MXL862XX_BRIDGE_FORWARD_FLOOD : MXL862XX_BRIDGE_FORWARD_DISCARD);
+
+	bridge_config.forward_unknown_multicast_ip = cpu_to_le32(mcast_flood ?
+		MXL862XX_BRIDGE_FORWARD_FLOOD : MXL862XX_BRIDGE_FORWARD_DISCARD);
+	bridge_config.forward_unknown_multicast_non_ip =
+		bridge_config.forward_unknown_multicast_ip;
+
+	bridge_config.forward_broadcast = cpu_to_le32(bcast_flood ?
+		MXL862XX_BRIDGE_FORWARD_FLOOD : MXL862XX_BRIDGE_FORWARD_DISCARD);
+
+	ret = MXL862XX_API_WRITE(priv, MXL862XX_BRIDGE_CONFIGSET, bridge_config);
+	if (ret)
+		dev_err(ds->dev, "failed to configure bridge %u forwarding: %d\n",
+			bridge_id, ret);
+
+	return ret;
+}
+
+/* Allocate a single zero-rate meter shared by all ports and flood types.
+ * All flood-blocking egress sub-meters point to this one meter so that
+ * the single CBS=64 token bucket fills as quickly as possible, minimising
+ * the one-packet leak inherent with the hardware minimum CBS.
+ */
+static int mxl862xx_setup_drop_meter(struct dsa_switch *ds)
+{
+	struct mxl862xx_qos_meter_cfg meter = {};
+	struct mxl862xx_priv *priv = ds->priv;
+	int ret;
+
+	/* meter_id=0 means auto-alloc */
+	ret = MXL862XX_API_READ(priv, MXL862XX_QOS_METERALLOC, meter);
+	if (ret)
+		return ret;
+
+	meter.enable = true;
+	meter.cbs = cpu_to_le32(64);
+	meter.ebs = cpu_to_le32(64);
+	snprintf(meter.meter_name, sizeof(meter.meter_name), "drop");
+
+	ret = MXL862XX_API_WRITE(priv, MXL862XX_QOS_METERCFGSET, meter);
+	if (ret)
+		return ret;
+
+	priv->drop_meter = le16_to_cpu(meter.meter_id);
+
+	return 0;
+}
+
 static int mxl862xx_setup(struct dsa_switch *ds)
 {
 	struct mxl862xx_priv *priv = ds->priv;
@@ -182,6 +252,15 @@ static int mxl862xx_setup(struct dsa_switch *ds)
 	if (ret)
 		return ret;
 
+	ret = mxl862xx_bridge_config_fwd(ds, MXL862XX_DEFAULT_BRIDGE,
+					 false, false, true);
+	if (ret)
+		return ret;
+
+	ret = mxl862xx_setup_drop_meter(ds);
+	if (ret)
+		return ret;
+
 	return mxl862xx_setup_mdio(ds);
 }
 
@@ -259,64 +338,241 @@ static int mxl862xx_configure_sp_tag_proto(struct dsa_switch *ds, int port,
 	return MXL862XX_API_WRITE(ds->priv, MXL862XX_SS_SPTAG_SET, tag);
 }
 
-static int mxl862xx_setup_cpu_bridge(struct dsa_switch *ds, int port)
+static int mxl862xx_set_bridge_port(struct dsa_switch *ds, int port)
 {
 	struct mxl862xx_bridge_port_config br_port_cfg = {};
 	struct mxl862xx_priv *priv = ds->priv;
-	u16 bridge_port_map = 0;
-	struct dsa_port *dp;
+	struct mxl862xx_port *p = &priv->ports[port];
+	u16 bridge_id = p->bridge ? p->bridge->bridge_id : p->fid;
+	bool enable;
+	int i, idx;
 
-	/* CPU port bridge setup */
-	br_port_cfg.mask = cpu_to_le32(MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_PORT_MAP |
+	br_port_cfg.bridge_port_id = cpu_to_le16(port);
+	br_port_cfg.bridge_id = cpu_to_le16(bridge_id);
+	br_port_cfg.mask = cpu_to_le32(MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_ID |
+				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_PORT_MAP |
 				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_MC_SRC_MAC_LEARNING |
-				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_VLAN_BASED_MAC_LEARNING);
+				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_EGRESS_SUB_METER);
+	br_port_cfg.src_mac_learning_disable = !p->learning;
 
-	br_port_cfg.bridge_port_id = cpu_to_le16(port);
-	br_port_cfg.src_mac_learning_disable = false;
-	br_port_cfg.vlan_src_mac_vid_enable = true;
-	br_port_cfg.vlan_dst_mac_vid_enable = true;
+	for (i = 0; i < ARRAY_SIZE(br_port_cfg.bridge_port_map); i++)
+		br_port_cfg.bridge_port_map[i] =
+			cpu_to_le16(bitmap_read(p->portmap, i * 16, 16));
+
+	for (i = 0; i < ARRAY_SIZE(mxl862xx_flood_meters); i++) {
+		idx = mxl862xx_flood_meters[i];
+		enable = !!(p->flood_block & BIT(idx));
+
+		br_port_cfg.egress_traffic_sub_meter_id[idx] =
+			enable ? cpu_to_le16(priv->drop_meter) : 0;
+		br_port_cfg.egress_sub_metering_enable[idx] = enable;
+	}
+
+	return MXL862XX_API_WRITE(priv, MXL862XX_BRIDGEPORT_CONFIGSET,
+				  br_port_cfg);
+}
+
+static int mxl862xx_setup_cpu_bridge(struct dsa_switch *ds, int port)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	struct dsa_port *dp;
+
+	priv->ports[port].fid = MXL862XX_DEFAULT_BRIDGE;
+	priv->ports[port].learning = true;
 
 	/* include all assigned user ports in the CPU portmap */
+	bitmap_zero(priv->ports[port].portmap, MXL862XX_MAX_BRIDGE_PORTS);
 	dsa_switch_for_each_user_port(dp, ds) {
 		/* it's safe to rely on cpu_dp being valid for user ports */
 		if (dp->cpu_dp->index != port)
 			continue;
 
-		bridge_port_map |= BIT(dp->index);
+		__set_bit(dp->index, priv->ports[port].portmap);
 	}
-	br_port_cfg.bridge_port_map[0] |= cpu_to_le16(bridge_port_map);
 
-	return MXL862XX_API_WRITE(priv, MXL862XX_BRIDGEPORT_CONFIGSET, br_port_cfg);
+	return mxl862xx_set_bridge_port(ds, port);
 }
 
 static int mxl862xx_add_single_port_bridge(struct dsa_switch *ds, int port)
 {
-	struct mxl862xx_bridge_port_config br_port_cfg = {};
 	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct mxl862xx_bridge_alloc br_alloc = {};
+	struct mxl862xx_priv *priv = ds->priv;
 	int ret;
 
-	ret = MXL862XX_API_READ(ds->priv, MXL862XX_BRIDGE_ALLOC, br_alloc);
+	ret = MXL862XX_API_READ(priv, MXL862XX_BRIDGE_ALLOC, br_alloc);
 	if (ret) {
 		dev_err(ds->dev, "failed to allocate a bridge for port %d\n", port);
 		return ret;
 	}
 
-	br_port_cfg.bridge_id = br_alloc.bridge_id;
-	br_port_cfg.bridge_port_id = cpu_to_le16(port);
-	br_port_cfg.mask = cpu_to_le32(MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_ID |
-				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_PORT_MAP |
-				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_MC_SRC_MAC_LEARNING |
-				       MXL862XX_BRIDGE_PORT_CONFIG_MASK_VLAN_BASED_MAC_LEARNING);
-	br_port_cfg.src_mac_learning_disable = true;
-	br_port_cfg.vlan_src_mac_vid_enable = false;
-	br_port_cfg.vlan_dst_mac_vid_enable = false;
-	/* As this function is only called for user ports it is safe to rely on
-	 * cpu_dp being valid
+	priv->ports[port].fid = le16_to_cpu(br_alloc.bridge_id);
+	priv->ports[port].learning = false;
+	bitmap_zero(priv->ports[port].portmap, MXL862XX_MAX_BRIDGE_PORTS);
+	__set_bit(dp->cpu_dp->index, priv->ports[port].portmap);
+
+	ret = mxl862xx_set_bridge_port(ds, port);
+	if (ret)
+		return ret;
+
+	/* Standalone ports should not flood unknown unicast or multicast
+	 * towards the CPU by default; only broadcast is needed initially.
 	 */
-	br_port_cfg.bridge_port_map[0] = cpu_to_le16(BIT(dp->cpu_dp->index));
+	return mxl862xx_bridge_config_fwd(ds, priv->ports[port].fid,
+					 false, false, true);
+}
+
+static struct mxl862xx_bridge *mxl862xx_allocate_bridge(struct dsa_switch *ds,
+							int num)
+{
+	struct mxl862xx_bridge_alloc br_alloc = {};
+	struct mxl862xx_priv *priv = ds->priv;
+	struct mxl862xx_bridge *mxlbridge;
+	int ret;
+
+	mxlbridge = kzalloc_obj(*mxlbridge);
+	if (!mxlbridge)
+		return ERR_PTR(-ENOMEM);
+
+	ret = MXL862XX_API_READ(priv, MXL862XX_BRIDGE_ALLOC, br_alloc);
+	if (ret) {
+		kfree(mxlbridge);
+		return ERR_PTR(ret);
+	}
+
+	mxlbridge->bridge_id = le16_to_cpu(br_alloc.bridge_id);
+	mxlbridge->dsa_bridge_num = num;
+
+	ret = mxl862xx_bridge_config_fwd(ds, mxlbridge->bridge_id,
+					 true, true, true);
+	if (ret) {
+		br_alloc.bridge_id = cpu_to_le16(mxlbridge->bridge_id);
+		MXL862XX_API_WRITE(priv, MXL862XX_BRIDGE_FREE, br_alloc);
+		kfree(mxlbridge);
+		return ERR_PTR(ret);
+	}
+
+	list_add(&mxlbridge->list, &priv->bridges);
+
+	return mxlbridge;
+}
+
+static void mxl862xx_free_bridge(struct dsa_switch *ds,
+				 struct mxl862xx_bridge *mxlbridge)
+{
+	struct mxl862xx_bridge_alloc br_alloc = {
+		.bridge_id = cpu_to_le16(mxlbridge->bridge_id),
+	};
+
+	MXL862XX_API_WRITE(ds->priv, MXL862XX_BRIDGE_FREE, br_alloc);
+	list_del(&mxlbridge->list);
+	kfree(mxlbridge);
+}
 
-	return MXL862XX_API_WRITE(ds->priv, MXL862XX_BRIDGEPORT_CONFIGSET, br_port_cfg);
+static struct mxl862xx_bridge *mxl862xx_find_bridge(struct dsa_switch *ds,
+						    struct dsa_bridge bridge)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	struct mxl862xx_bridge *mxlbridge;
+
+	if (!bridge.num)
+		return NULL;
+
+	list_for_each_entry(mxlbridge, &priv->bridges, list) {
+		if (mxlbridge->dsa_bridge_num == bridge.num)
+			return mxlbridge;
+	}
+
+	return NULL;
+}
+
+static int mxl862xx_sync_bridge_members(struct dsa_switch *ds,
+					struct mxl862xx_bridge *mxlbridge)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	int err, member, ret = 0;
+	struct dsa_port *dp;
+
+	/* Update all current bridge members' portmaps */
+	for_each_set_bit(member, mxlbridge->portmap,
+			 MXL862XX_MAX_BRIDGE_PORTS) {
+		dp = dsa_to_port(ds, member);
+
+		/* Build portmap: CPU port + all bridge members except self */
+		bitmap_copy(priv->ports[member].portmap, mxlbridge->portmap,
+			    MXL862XX_MAX_BRIDGE_PORTS);
+		__clear_bit(member, priv->ports[member].portmap);
+		__set_bit(dp->cpu_dp->index, priv->ports[member].portmap);
+
+		err = mxl862xx_set_bridge_port(ds, member);
+		if (err)
+			ret = err;
+	}
+
+	return ret;
+}
+
+static int mxl862xx_port_bridge_join(struct dsa_switch *ds, int port,
+				     struct dsa_bridge bridge,
+				     bool *tx_fwd_offload,
+				     struct netlink_ext_ack *extack)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	struct mxl862xx_bridge *mxlbridge;
+
+	mxlbridge = mxl862xx_find_bridge(ds, bridge);
+	if (!mxlbridge) {
+		mxlbridge = mxl862xx_allocate_bridge(ds, bridge.num);
+		if (IS_ERR(mxlbridge))
+			return PTR_ERR(mxlbridge);
+	}
+
+	__set_bit(port, mxlbridge->portmap);
+	priv->ports[port].bridge = mxlbridge;
+
+	/* The operation may fail mid way and there is no way to restore
+	 * the driver in sync with a known FW state. So we consider FW
+	 * I/O failure as catastrophic, no point to complicate the
+	 * driver by restoring mxlbridge->portmap or the bridge pointer.
+	 */
+	return mxl862xx_sync_bridge_members(ds, mxlbridge);
+}
+
+static void mxl862xx_port_bridge_leave(struct dsa_switch *ds, int port,
+				       struct dsa_bridge bridge)
+{
+	struct dsa_port *dp = dsa_to_port(ds, port);
+	struct mxl862xx_priv *priv = ds->priv;
+	struct mxl862xx_bridge *mxlbridge;
+	int err;
+
+	mxlbridge = mxl862xx_find_bridge(ds, bridge);
+	if (!mxlbridge)
+		return;
+
+	__clear_bit(port, mxlbridge->portmap);
+	priv->ports[port].bridge = NULL;
+
+	err = mxl862xx_sync_bridge_members(ds, mxlbridge);
+	if (err)
+		dev_err(ds->dev,
+			"failed to sync bridge members after port %d left: %pe\n",
+			port, ERR_PTR(err));
+
+	/* Revert leaving port, omitted by the sync above, to its
+	 * single-port bridge
+	 */
+	bitmap_zero(priv->ports[port].portmap, MXL862XX_MAX_BRIDGE_PORTS);
+	__set_bit(dp->cpu_dp->index, priv->ports[port].portmap);
+	priv->ports[port].flood_block = 0;
+	err = mxl862xx_set_bridge_port(ds, port);
+	if (err)
+		dev_err(ds->dev,
+			"failed to update bridge port %d state: %pe\n", port,
+			ERR_PTR(err));
+
+	if (bitmap_empty(mxlbridge->portmap, MXL862XX_MAX_BRIDGE_PORTS))
+		mxl862xx_free_bridge(ds, mxlbridge);
 }
 
 static int mxl862xx_port_setup(struct dsa_switch *ds, int port)
@@ -366,6 +622,264 @@ static void mxl862xx_phylink_get_caps(struct dsa_switch *ds, int port,
 		  config->supported_interfaces);
 }
 
+static int mxl862xx_get_fid(struct dsa_switch *ds, struct dsa_db db)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	struct mxl862xx_bridge *mxlbridge;
+
+	switch (db.type) {
+	case DSA_DB_PORT:
+		return priv->ports[db.dp->index].fid;
+
+	case DSA_DB_BRIDGE:
+		mxlbridge = mxl862xx_find_bridge(ds, db.bridge);
+		if (!mxlbridge)
+			return -ENOENT;
+		return mxlbridge->bridge_id;
+
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int mxl862xx_port_fdb_add(struct dsa_switch *ds, int port,
+				 const unsigned char *addr, u16 vid, struct dsa_db db)
+{
+	struct mxl862xx_mac_table_add param = { };
+	int fid = mxl862xx_get_fid(ds, db), ret;
+	struct mxl862xx_priv *priv = ds->priv;
+
+	if (fid < 0)
+		return fid;
+
+	param.port_id = cpu_to_le32(port);
+	param.static_entry = true;
+	param.fid = cpu_to_le16(fid);
+	param.tci = cpu_to_le16(FIELD_PREP(MXL862XX_TCI_VLAN_ID, vid));
+	ether_addr_copy(param.mac, addr);
+
+	ret = MXL862XX_API_WRITE(priv, MXL862XX_MAC_TABLEENTRYADD, param);
+	if (ret)
+		dev_err(ds->dev, "failed to add FDB entry on port %d\n", port);
+
+	return ret;
+}
+
+static int mxl862xx_port_fdb_del(struct dsa_switch *ds, int port,
+				 const unsigned char *addr, u16 vid, struct dsa_db db)
+{
+	struct mxl862xx_mac_table_remove param = { };
+	int fid = mxl862xx_get_fid(ds, db), ret;
+	struct mxl862xx_priv *priv = ds->priv;
+
+	if (fid < 0)
+		return fid;
+
+	param.fid = cpu_to_le16(fid);
+	param.tci = cpu_to_le16(FIELD_PREP(MXL862XX_TCI_VLAN_ID, vid));
+	ether_addr_copy(param.mac, addr);
+
+	ret = MXL862XX_API_WRITE(priv, MXL862XX_MAC_TABLEENTRYREMOVE, param);
+	if (ret)
+		dev_err(ds->dev, "failed to remove FDB entry on port %d\n", port);
+
+	return ret;
+}
+
+static int mxl862xx_port_fdb_dump(struct dsa_switch *ds, int port,
+				  dsa_fdb_dump_cb_t *cb, void *data)
+{
+	struct mxl862xx_mac_table_read param = { };
+	struct mxl862xx_priv *priv = ds->priv;
+	u32 entry_port_id;
+	int ret;
+
+	while (true) {
+		ret = MXL862XX_API_READ(priv, MXL862XX_MAC_TABLEENTRYREAD, param);
+		if (ret)
+			return ret;
+
+		if (param.last)
+			break;
+
+		entry_port_id = le32_to_cpu(param.port_id);
+
+		if (entry_port_id == port) {
+			ret = cb(param.mac, FIELD_GET(MXL862XX_TCI_VLAN_ID,
+						      le16_to_cpu(param.tci)),
+				 param.static_entry, data);
+			if (ret)
+				return ret;
+		}
+
+		memset(&param, 0, sizeof(param));
+	}
+
+	return 0;
+}
+
+static int mxl862xx_port_mdb_add(struct dsa_switch *ds, int port,
+				 const struct switchdev_obj_port_mdb *mdb,
+				 struct dsa_db db)
+{
+	return mxl862xx_port_fdb_add(ds, port, mdb->addr, mdb->vid, db);
+}
+
+static int mxl862xx_port_mdb_del(struct dsa_switch *ds, int port,
+				 const struct switchdev_obj_port_mdb *mdb,
+				 struct dsa_db db)
+{
+	return mxl862xx_port_fdb_del(ds, port, mdb->addr, mdb->vid, db);
+}
+
+static int mxl862xx_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
+{
+	struct mxl862xx_cfg param;
+	int ret;
+
+	ret = MXL862XX_API_READ(ds->priv, MXL862XX_COMMON_CFGGET, param);
+	if (ret) {
+		dev_err(ds->dev, "failed to read switch config\n");
+		return ret;
+	}
+
+	param.mac_table_age_timer = cpu_to_le32(MXL862XX_AGETIMER_CUSTOM);
+	param.age_timer = cpu_to_le32(msecs / 1000);
+	ret = MXL862XX_API_WRITE(ds->priv, MXL862XX_COMMON_CFGSET, param);
+	if (ret)
+		dev_err(ds->dev, "failed to set ageing\n");
+
+	return ret;
+}
+
+static void mxl862xx_port_stp_state_set(struct dsa_switch *ds, int port,
+					u8 state)
+{
+	struct mxl862xx_stp_port_cfg param = {
+		.port_id = cpu_to_le16(port),
+	};
+	struct mxl862xx_priv *priv = ds->priv;
+	int ret;
+
+	switch (state) {
+	case BR_STATE_DISABLED:
+		param.port_state = cpu_to_le32(MXL862XX_STP_PORT_STATE_DISABLE);
+		break;
+	case BR_STATE_BLOCKING:
+	case BR_STATE_LISTENING:
+		param.port_state = cpu_to_le32(MXL862XX_STP_PORT_STATE_BLOCKING);
+		break;
+	case BR_STATE_LEARNING:
+		param.port_state = cpu_to_le32(MXL862XX_STP_PORT_STATE_LEARNING);
+		break;
+	case BR_STATE_FORWARDING:
+		param.port_state = cpu_to_le32(MXL862XX_STP_PORT_STATE_FORWARD);
+		break;
+	default:
+		dev_err(ds->dev, "invalid STP state: %d\n", state);
+		return;
+	}
+
+	ret = MXL862XX_API_WRITE(priv, MXL862XX_STP_PORTCFGSET, param);
+	if (ret) {
+		dev_err(ds->dev, "failed to set STP state on port %d\n", port);
+		return;
+	}
+
+	/* The firmware may re-enable MAC learning as a side-effect of entering
+	 * LEARNING or FORWARDING state (per 802.1D defaults).
+	 * Re-apply the driver's intended learning and metering config so that
+	 * standalone ports keep learning disabled.
+	 * This is likely to get fixed in future firmware releases, however,
+	 * the additional API call even then doesn't hurt much.
+	 */
+	ret = mxl862xx_set_bridge_port(ds, port);
+	if (ret)
+		dev_err(ds->dev, "failed to reapply brport flags on port %d\n",
+			port);
+
+	mxl862xx_port_fast_age(ds, port);
+}
+
+static void mxl862xx_port_set_host_flood(struct dsa_switch *ds, int port,
+					 bool uc, bool mc)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+
+	/* The hardware controls unknown-unicast/multicast forwarding per FID
+	 * (bridge), not per source port. For bridged ports all members share
+	 * one FID, so we cannot selectively suppress flooding to the CPU for
+	 * one source port while allowing it for another. Silently ignore the
+	 * request - the excess flooding towards the CPU is harmless.
+	 */
+	if (priv->ports[port].bridge)
+		return;
+
+	/* Use the bridge-level forwarding configuration of the port's
+	 * single-port bridge to control host flooding for standalone ports.
+	 */
+	mxl862xx_bridge_config_fwd(ds, priv->ports[port].fid, uc, mc, true);
+}
+
+static int mxl862xx_port_pre_bridge_flags(struct dsa_switch *ds, int port,
+					  struct switchdev_brport_flags flags,
+					  struct netlink_ext_ack *extack)
+{
+	if (flags.mask & ~(BR_FLOOD | BR_MCAST_FLOOD | BR_BCAST_FLOOD |
+			   BR_LEARNING))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int mxl862xx_port_bridge_flags(struct dsa_switch *ds, int port,
+				      struct switchdev_brport_flags flags,
+				      struct netlink_ext_ack *extack)
+{
+	struct mxl862xx_priv *priv = ds->priv;
+	unsigned long old_block = priv->ports[port].flood_block;
+	unsigned long block = old_block;
+	bool need_update = false;
+	int ret;
+
+	if (flags.mask & BR_FLOOD) {
+		if (flags.val & BR_FLOOD)
+			block &= ~BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_UC);
+		else
+			block |= BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_UC);
+	}
+
+	if (flags.mask & BR_MCAST_FLOOD) {
+		if (flags.val & BR_MCAST_FLOOD) {
+			block &= ~BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_IP);
+			block &= ~BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_NON_IP);
+		} else {
+			block |= BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_IP);
+			block |= BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_UNKNOWN_MC_NON_IP);
+		}
+	}
+
+	if (flags.mask & BR_BCAST_FLOOD) {
+		if (flags.val & BR_BCAST_FLOOD)
+			block &= ~BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_BROADCAST);
+		else
+			block |= BIT(MXL862XX_BRIDGE_PORT_EGRESS_METER_BROADCAST);
+	}
+
+	if (flags.mask & BR_LEARNING)
+		priv->ports[port].learning = !!(flags.val & BR_LEARNING);
+
+	need_update = (block != old_block) || (flags.mask & BR_LEARNING);
+	if (need_update) {
+		priv->ports[port].flood_block = block;
+		ret = mxl862xx_set_bridge_port(ds, port);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
 static const struct dsa_switch_ops mxl862xx_switch_ops = {
 	.get_tag_protocol = mxl862xx_get_tag_protocol,
 	.setup = mxl862xx_setup,
@@ -374,6 +888,18 @@ static const struct dsa_switch_ops mxl862xx_switch_ops = {
 	.port_enable = mxl862xx_port_enable,
 	.port_disable = mxl862xx_port_disable,
 	.port_fast_age = mxl862xx_port_fast_age,
+	.set_ageing_time = mxl862xx_set_ageing_time,
+	.port_bridge_join = mxl862xx_port_bridge_join,
+	.port_bridge_leave = mxl862xx_port_bridge_leave,
+	.port_pre_bridge_flags = mxl862xx_port_pre_bridge_flags,
+	.port_bridge_flags = mxl862xx_port_bridge_flags,
+	.port_stp_state_set = mxl862xx_port_stp_state_set,
+	.port_set_host_flood = mxl862xx_port_set_host_flood,
+	.port_fdb_add = mxl862xx_port_fdb_add,
+	.port_fdb_del = mxl862xx_port_fdb_del,
+	.port_fdb_dump = mxl862xx_port_fdb_dump,
+	.port_mdb_add = mxl862xx_port_mdb_add,
+	.port_mdb_del = mxl862xx_port_mdb_del,
 };
 
 static void mxl862xx_phylink_mac_config(struct phylink_config *config,
@@ -415,6 +941,8 @@ static int mxl862xx_probe(struct mdio_device *mdiodev)
 
 	priv->mdiodev = mdiodev;
 
+	INIT_LIST_HEAD(&priv->bridges);
+
 	ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
 	if (!ds)
 		return -ENOMEM;
@@ -425,6 +953,8 @@ static int mxl862xx_probe(struct mdio_device *mdiodev)
 	ds->ops = &mxl862xx_switch_ops;
 	ds->phylink_mac_ops = &mxl862xx_phylink_mac_ops;
 	ds->num_ports = MXL862XX_MAX_PORTS;
+	ds->fdb_isolation = true;
+	ds->max_num_bridges = MXL862XX_MAX_BRIDGES;
 
 	dev_set_drvdata(dev, ds);
 
diff --git a/drivers/net/dsa/mxl862xx/mxl862xx.h b/drivers/net/dsa/mxl862xx/mxl862xx.h
index bfeb436942d5f..f1bd194cb3114 100644
--- a/drivers/net/dsa/mxl862xx/mxl862xx.h
+++ b/drivers/net/dsa/mxl862xx/mxl862xx.h
@@ -7,10 +7,62 @@
 #include <net/dsa.h>
 
 #define MXL862XX_MAX_PORTS		17
+#define MXL862XX_DEFAULT_BRIDGE		0
+#define MXL862XX_MAX_BRIDGES		48
+#define MXL862XX_MAX_BRIDGE_PORTS	128
 
+/**
+ * struct mxl862xx_bridge - per-bridge state tracked by the driver
+ * @dsa_bridge_num: DSA framework bridge number, as returned by
+ *                  dsa_switch_bridge_join()
+ * @bridge_id:      firmware FID assigned to this bridge
+ * @portmap:        bitmap of ports belonging to this bridge
+ * @list:           entry in &mxl862xx_priv.bridges
+ */
+struct mxl862xx_bridge {
+	unsigned int dsa_bridge_num;
+	u16 bridge_id;
+	DECLARE_BITMAP(portmap, MXL862XX_MAX_BRIDGE_PORTS);
+	struct list_head list;
+};
+
+/**
+ * struct mxl862xx_port - per-port state tracked by the driver
+ * @fid:         firmware FID for the permanent single-port bridge; kept alive
+ *               for the lifetime of the port so traffic is never forwarded
+ *               while the port is unbridged
+ * @bridge:      bridge this port currently belongs to, or %NULL if unbridged
+ * @portmap:     bitmap of switch port indices that share the current bridge
+ *               with this port (mirrors @bridge->portmap for convenience)
+ * @flood_block: bitmask of firmware meter indices that are currently
+ *               rate-limiting flood traffic on this port (zero-rate meters
+ *               used to block flooding)
+ * @learning:    true when address learning is enabled on this port
+ */
+struct mxl862xx_port {
+	u16 fid;
+	struct mxl862xx_bridge *bridge;
+	DECLARE_BITMAP(portmap, MXL862XX_MAX_BRIDGE_PORTS);
+	unsigned long flood_block;
+	bool learning;
+};
+
+/**
+ * struct mxl862xx_priv - driver private data for an MxL862xx switch
+ * @ds:          pointer to the DSA switch instance
+ * @mdiodev:     MDIO device used to communicate with the switch firmware
+ * @drop_meter:  index of the single shared zero-rate firmware meter used
+ *               to unconditionally drop traffic (used to block flooding)
+ * @ports:       per-port state, indexed by switch port number
+ * @bridges:     list of &struct mxl862xx_bridge instances currently offloaded
+ *               to the hardware
+ */
 struct mxl862xx_priv {
 	struct dsa_switch *ds;
 	struct mdio_device *mdiodev;
+	u16 drop_meter;
+	struct mxl862xx_port ports[MXL862XX_MAX_PORTS];
+	struct list_head bridges;
 };
 
 #endif /* __MXL862XX_H */
-- 
2.53.0

Re: [PATCH net-next v4 2/2] net: dsa: mxl862xx: implement bridge offloading

[Daniel Golle]

On Thu, Mar 12, 2026 at 03:33:30AM +0000, Daniel Golle wrote:
> Add support for bridge offloading on the mxl862xx DSA driver.

> +static int mxl862xx_port_mdb_add(struct dsa_switch *ds, int port,
> +				 const struct switchdev_obj_port_mdb *mdb,
> +				 struct dsa_db db)
> +{
> +	return mxl862xx_port_fdb_add(ds, port, mdb->addr, mdb->vid, db);
> +}
> +
> +static int mxl862xx_port_mdb_del(struct dsa_switch *ds, int port,
> +				 const struct switchdev_obj_port_mdb *mdb,
> +				 struct dsa_db db)
> +{
> +	return mxl862xx_port_fdb_del(ds, port, mdb->addr, mdb->vid, db);
> +}

The .port_mdb_* functions were left-overs from my previous experiments
and should not have been part of the submitted series. I've noticed that
only now. Apart from that this patch is ready for review imho, so I won't
send any new version at this point until receiving more feedback.