From: mingming cao <mmc@linux.ibm.com>
To: netdev-bot+sashiko@kernel.org
Cc: netdev@vger.kernel.org, davem@davemloft.net, kuba@kernel.org,
horms@kernel.org, edumazet@kernel.org, pabeni@redhat.com,
andrew+netdev@lunn.ch, nnac123@linux.ibm.com,
maddy@linux.ibm.com, mpe@ellerman.id.au,
linuxppc-dev@lists.ozlabs.org, npiggin@gmail.com,
chleroy@kernel.org, ritesh.list@gmail.com, sshegde@linux.ibm.com,
haren@linux.ibm.com, ricklind@linux.ibm.com,
davemarq@linux.ibm.com, bjking1@linux.ibm.com,
shaik.abdulla1@ibm.com
Subject: Re: [PATCH net-next v8 14/15] ibmveth: Implement incremental MQ RX queue resize
Date: Fri, 13 Nov 2026 11:07:10 -0800 [thread overview]
Message-ID: <ea18450c-bfc6-48f4-9b08-fad59c880807@linux.ibm.com> (raw)
In-Reply-To: <179452783301.2199510.7559323985625318822@kernel.org>
On 11/12/26 3:57 PM, netdev-bot+sashiko@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 3 potential
> issue(s) to consider.
>
> Critical: 0 · High: 0 · Medium: 1 · Low: 2
>
> If you believe none of the issues are legitimate, please reply to each
> issue of Medium severity or higher and explain why the AI is wrong.
> If any of them are legitimate and you plan to respin, please let patchwork
> know by including "pw-bot: cr" as a separate line at the end of your reply
> (one such reply per series is enough).
>
> - [Medium] ibmveth_destroy_subordinate_rx_queue() is used for live
> ethtool -L scale-down, the scale-up enable_irq-failure branch and the…
> - [Low] When a scale-down hits the destroy-failure keep path,
> ibmveth_scale_down_rx_queues() (drivers/net/ethernet/ibm/ibmveth.c)…
> - [Low] The kernel-doc of ibmveth_scale_up_rx_queues() says "A failure
> unwinds only the queues this call added; a queue PHYP refuses to…
>
> --
>
> ibmveth: Implement incremental MQ RX queue resize
>
> This commit lets ethtool -L change the RX queue count on a live ibmveth
> adapter one queue at a time. It adds ibmveth_scale_up_rx_queues() and
> ibmveth_scale_down_rx_queues(), with unwind paths for hypervisor
> failures. It also factors ibmveth_desired_dma_for_rxqs() out of
> ibmveth_get_desired_dma(), and frees queues stranded above the live
> count after a successful H_FREE_LOGICAL_LAN.
>
>> diff --git a/drivers/net/ethernet/ibm/ibmveth.c b/drivers/net/ethernet/ibm/ibmveth.c
>> index e805e7b1d2fe2..510d9d80e2df5 100644
>> --- a/drivers/net/ethernet/ibm/ibmveth.c
>> +++ b/drivers/net/ethernet/ibm/ibmveth.c
> [ ... ]
>
>> @@ -2028,6 +2315,644 @@ static void ibmveth_release_lan_resources(struct ibmveth_adapter *adapter)
>> ibmveth_free_filter_list(adapter);
>> }
>>
> [ ... ]
>
>> +/**
>> + * ibmveth_destroy_subordinate_rx_queue - Tear down one subordinate RX queue
>> + * @adapter: ibmveth adapter structure
>> + * @queue_idx: Queue index to destroy (1..N)
>> + *
>> + * Deregister with PHYP before unmapping buffer pools so hypervisor buffer
>> + * ownership is released while queue metadata is still valid. After a
>> + * successful H_FREE, fold the last no_buffer sample into retired while
>> + * the page is still mapped. If the hcall fails, leave the queue mapped,
>> + * keep the handle, and skip retire.
>> + *
>> + * Return: 0 on success, -EIO if deregister failed
>> + */
>> +static int
>> +ibmveth_destroy_subordinate_rx_queue(struct ibmveth_adapter *adapter,
>> + int queue_idx)
>> +{
>> + int rc;
>> +
>> + rc = ibmveth_deregister_single_rx_queue(adapter, queue_idx);
>> + if (rc)
>> + return rc;
>> + ibmveth_retire_rx_no_buffer(adapter, queue_idx);
>> + ibmveth_cleanup_single_rx_interrupt(adapter, queue_idx);
>> + ibmveth_free_single_rx_queue(adapter, queue_idx);
>> + return 0;
>> +}
> [Severity: Medium]
> Is the order of H_FREE_LOGICAL_LAN_QUEUE and the IRQ teardown safe here?
>
> ibmveth_deregister_single_rx_queue() issues H_FREE_LOGICAL_LAN_QUEUE
> first. Only after that does ibmveth_cleanup_single_rx_interrupt() run
> free_irq() and irq_dispose_mapping() on the queue's virq. That virq was
> created by irq_create_mapping(NULL, hwirq), using the hwirq returned by
> H_REG_LOGICAL_LAN_QUEUE. So the interrupt source belongs to the queue
> being freed.
>
> On pseries XIVE, free_irq() reaches xive_irq_shutdown(), which does an
> ESB access and an H_INT_SET_SOURCE_CONFIG hcall against that source:
>
> arch/powerpc/sysdev/xive/common.c:xive_irq_shutdown() {
> ...
> xive_do_source_set_mask(xd, true);
> xive_ops->configure_irq(hw_irq,
> get_hard_smp_processor_id(xd->target),
> 0xff, XIVE_BAD_IRQ);
> ...
> }
>
> irq_dispose_mapping() then tears down the per-source XIVE data and its
> ESB mapping.
>
> If H_FREE_LOGICAL_LAN_QUEUE releases the LISN, these operations would
> run against a source the partition no longer owns. Could that produce
> failed hcalls, stale irq_desc state, or an ESB access to a page the
> hypervisor no longer backs?
Checked this with the PHYP team. H_FREE_LOGICAL_LAN and
H_FREE_LOGICAL_LAN_QUEUE don't release the interrupt source; the sources
stay allocated while the adapter is allocated, including while it's
down, and can be masked or unmasked during that time. Before this path
calls H_FREE_LOGICAL_LAN_QUEUE, scale-down has already masked the queue
in PHYP with H_VIOCTL and waited for the handler with synchronize_irq().
> The rest of this driver tears the IRQ down first:
>
> - ibmveth_close() runs ibmveth_cleanup_rx_interrupts() before
> ibmveth_free_all_queues().
> - The open() error path disposes the mappings before
> H_FREE_LOGICAL_LAN.
> - The scale-up request_irq failure branch disposes before it
> deregisters.
>
> ibmvnic's release_sub_crqs() also calls free_irq() and
> irq_dispose_mapping() before release_sub_crq_queue() issues
> H_FREE_SUB_CRQ.
>
> The commit message explains why deregister has to come before the DMA
> unmap, but not why it has to come before the IRQ teardown. Would it
> work to keep PHYP masked, call free_irq() (and dispose the mapping),
> then issue H_FREE_LOGICAL_LAN_QUEUE, and re-request the IRQ in the rare
> case the hcall fails?
The order is there for the rollback path, not the normal success path.
If H_FREE_LOGICAL_LAN_QUEUE fails with something other than busy, the
queue stays registered and PHYP may still DMA into it. Scale-down and
the scale-up unwind then put that same queue back in service by
enabling NAPI and unmasking the same virq. If we'd already freed the
IRQ and disposed the mapping before the H_FREE, the failure path would
have to rebuild the mapping and request the IRQ again in the middle of a
rollback that's already failing.
So destroy keeps the IRQ until H_FREE succeeds, or until H_PARAMETER
says the queue is already free. I'd rather not reorder just to match
close(): close() can free the IRQs first because it never has to put
the LAN back in service after a failed H_FREE_LOGICAL_LAN.
Thanks,
Mingming
next prev parent reply other threads:[~2026-11-13 19:07 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-09 23:55 [PATCH net-next v8 00/15] ibmveth: Add multi-queue RX support Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 01/15] ibmveth: Add MQ RX hypercall wrappers and call definitions Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 02/15] ibmveth: Prepare MQ RX adapter data structures Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 03/15] ibmveth: Refactor RX resource allocation for MQ RX bring-up Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 04/15] ibmveth: Refactor buffer pool management for per-queue MQ RX Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 05/15] ibmveth: Refactor RX interrupt control for MQ RX queues Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-13 18:46 ` mingming cao
2026-11-09 23:55 ` [PATCH net-next v8 06/15] ibmveth: Refactor TX resource allocation in open/close paths Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-13 18:54 ` mingming cao
2026-11-09 23:55 ` [PATCH net-next v8 07/15] ibmveth: Add RX queue register helpers for MQ Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-09 23:55 ` [PATCH net-next v8 08/15] ibmveth: Add queue-aware RX buffer submit helper " Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-09 23:55 ` [PATCH net-next v8 09/15] ibmveth: Split RX poll into per-slot helpers " Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-09 23:55 ` [PATCH net-next v8 10/15] ibmveth: Enable multi-queue RX receive path Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-13 18:59 ` mingming cao
2026-11-09 23:55 ` [PATCH net-next v8 11/15] ibmveth: Add per-queue RX and TX statistics collection Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-13 19:00 ` mingming cao
2026-11-09 23:55 ` [PATCH net-next v8 12/15] ibmveth: Report MQ-aware RX counts in ethtool get_channels Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 13/15] ibmveth: Expose per-queue buffer pool details via debugfs Mingming Cao
2026-11-09 23:55 ` [PATCH net-next v8 14/15] ibmveth: Implement incremental MQ RX queue resize Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
2026-11-13 19:07 ` mingming cao [this message]
2026-11-09 23:55 ` [PATCH net-next v8 15/15] ibmveth: Complete set_channels down-path Mingming Cao
2026-11-12 23:57 ` netdev-bot+sashiko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ea18450c-bfc6-48f4-9b08-fad59c880807@linux.ibm.com \
--to=mmc@linux.ibm.com \
--cc=andrew+netdev@lunn.ch \
--cc=bjking1@linux.ibm.com \
--cc=chleroy@kernel.org \
--cc=davem@davemloft.net \
--cc=davemarq@linux.ibm.com \
--cc=edumazet@kernel.org \
--cc=haren@linux.ibm.com \
--cc=horms@kernel.org \
--cc=kuba@kernel.org \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=maddy@linux.ibm.com \
--cc=mpe@ellerman.id.au \
--cc=netdev-bot+sashiko@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nnac123@linux.ibm.com \
--cc=npiggin@gmail.com \
--cc=pabeni@redhat.com \
--cc=ricklind@linux.ibm.com \
--cc=ritesh.list@gmail.com \
--cc=shaik.abdulla1@ibm.com \
--cc=sshegde@linux.ibm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox