* Re: Route cache performance
From: Alexey Kuznetsov @ 2005-09-07 19:59 UTC (permalink / raw)
To: Simon Kirby; +Cc: Robert Olsson, Alexey Kuznetsov, Eric Dumazet, netdev
In-Reply-To: <20050907162854.GB24735@netnation.com>
Hello!
> Yes, setting maxbatch to 10000 also results in working gc,
Could you try lower values? F.e. I guess 300 or a little more
(it is netdev_max_backlog) should be enough.
> for the normal case also hurts the DoS case...and it really hurts when
> the when the DoS case is the normal case.
5.7% is not "really hurts" yet. :-)
Alexey
^ permalink raw reply
* Re: [patch 1/1] ipw2100: remove by-hand function entry/exit debugging
From: David S. Miller @ 2005-09-07 20:01 UTC (permalink / raw)
To: netdev; +Cc: jgarzik, akpm, pavel, ipw2100-admin, pavel, linux-kernel, netdev
In-Reply-To: <200509071539.08780.netdev@axxeo.de>
From: Ingo Oeser <netdev@axxeo.de>
Date: Wed, 7 Sep 2005 15:39:08 +0200
> Jeff Garzik wrote:
> > I find them useful in my own drivers; they are definitely not pure noise.
>
> gcc -finstrument-functions
I was going to mention this as well, and also the idea to
enable CONFIG_MCOUNT on a per-file basis.
We should never be doing by hand what can be automated.
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Marc Lehmann @ 2005-09-07 20:59 UTC (permalink / raw)
To: Patrick McHardy; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <431EDF78.8060505@trash.net>
On Wed, Sep 07, 2005 at 02:39:20PM +0200, Patrick McHardy <kaber@trash.net> wrote:
> Andrew Morton wrote:
Thanks for your response!
> > tcp 6 52 SYN_SENT src=10.0.0.1 dst=129.13.162.95 sport=44320
> > dport=80 [UNREPLIED] src=129.13.162.95 dst=84.56.237.68 sport=80
> > dport=44320 mark=0 use=1
>
> It seems ip_conntrack did not like the SYN/ACK and marked it as invalid,
> NAT leaves the packet alone and the firewall resets the connection.
> Please try if loading the ipt_LOG module and executing
> "echo 255 > /proc/sys/net/ipv4/netfilter/ip_conntrack_log_invalid"
> gives more information
I think I have the LOG target compiled into the kernel. After the echo, I got
this within a matter of seconds:
printk: 614 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxxxxxxxxxxx DST=84.56.231.206 LEN=105 TOS=0x00 PREC=0x00 TTL=53 ID=33989 DF PROTO=TCP SPT=119 DPT=41349 SEQ=495763142 ACK=177548929 WINDOW=56677 RES=0x00 ACK PSH URGP=0 OPT (0101080A0986EF9D00E16123)
This is interesting, as the connection in question seems to work fine (at
least I can download news at 32kb/s, which is the rate limit on the other
side without much more than 32kb/s on my ppp link, so it is weird that
this many packets should have invalid tcp checksum. Maybe this is somehow
related?)
I then tried to create a masqueraded connection and got the expected
symptoms: correctly re-written packet leaves interface, return packet gets
RST.
During that time, I got more of the above messages, but none related to the
test connection.
I then stopped all traffic-generating programs to get an idle link and
retried. Still no log messages from the test conenction.
> >eth0:
> > 19:23:29.928470 IP 10.0.0.1.45611 > 129.13.162.95.80: S
> > 4113365634:4113365634(0) win 5840 <mss 1460>
> > 19:23:29.942246 IP 129.13.162.95.80 > 10.0.0.1.45611: S
> > 4161877683:4161877683(0) ack 4113365635 win 5840 <mss 1460>
> > 19:23:29.942313 IP 10.0.0.1.45611 > 129.13.162.95.80: . ack 1 win 5840
> >
> >inet:
> > 19:23:29.928249 IP 84.56.237.68.45611 > 129.13.162.95.80: S
> > 4113365634:4113365634(0) win 5840 <mss 1452>
> > 19:23:29.942199 IP 129.13.162.95.80 > 84.56.237.68.45611: S
> > 4161877683:4161877683(0) ack 4113365635 win 5840 <mss 1460>
> > 19:23:29.942332 IP 84.56.237.68.45611 > 129.13.162.95.80: . ack 1 win
> > 5840
> >
> >However, ICMP still is not masqueraded.
>
> Please also try this again with logging enabled.
No messages, either.
(As I wrote in another mail), I also found in the meantime that switching
off SACK only results in a correct handshake, further packets might and
usually will cause a RST.
> >Kernels that don't work:
> >
> > 2.6.13-rc7 (compiled with gcc-3.4 and 4.0.2 debian), 2.6.13 (gcc-4.02)
>
> Can you retest with 2.6.12.5 on 64bit so we can see if it is a new
> problem?
I hope that trying with 2.6.11, and getting the same problem (as I did in
the meantime), is even better than testing 2.6.12.5.
> So far I don't think its related to routed.
The weird thing is that it works on tap, but not on ethernet/ppp. Maybe
the kernel code gets some offset wrong?
--
The choice of a
-----==- _GNU_
----==-- _ generation Marc Lehmann
---==---(_)__ __ ____ __ pcg@goof.com
--==---/ / _ \/ // /\ \/ / http://schmorp.de/
-=====/_/_//_/\_,_/ /_/\_\ XX11-RIPE
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Patrick McHardy @ 2005-09-07 21:34 UTC (permalink / raw)
To: Marc Lehmann; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <20050907205923.GA6567@schmorp.de>
Marc Lehmann wrote:
> I think I have the LOG target compiled into the kernel. After the echo, I got
> this within a matter of seconds:
>
> printk: 614 messages suppressed.
> ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxxxxxxxxxxx DST=84.56.231.206 LEN=105 TOS=0x00 PREC=0x00 TTL=53 ID=33989 DF PROTO=TCP SPT=119 DPT=41349 SEQ=495763142 ACK=177548929 WINDOW=56677 RES=0x00 ACK PSH URGP=0 OPT (0101080A0986EF9D00E16123)
Interesting .. if this isn't real there is most likely some problem with
HW checksumming in netfilter. What does ethtool -k <dev> show?
> This is interesting, as the connection in question seems to work fine (at
> least I can download news at 32kb/s, which is the rate limit on the other
> side without much more than 32kb/s on my ppp link, so it is weird that
> this many packets should have invalid tcp checksum. Maybe this is somehow
> related?)
>
> I then tried to create a masqueraded connection and got the expected
> symptoms: correctly re-written packet leaves interface, return packet gets
> RST.
>
> During that time, I got more of the above messages, but none related to the
> test connection.
Could be because of net_ratelimit() message surpressing.
> (As I wrote in another mail), I also found in the meantime that switching
> off SACK only results in a correct handshake, further packets might and
> usually will cause a RST.
I'm not aware of any special handling for SACKs that would make it fail,
especially considering that ICMP also fails, but I'm going to look into
it.
>>>Kernels that don't work:
>>>
>>> 2.6.13-rc7 (compiled with gcc-3.4 and 4.0.2 debian), 2.6.13 (gcc-4.02)
>>
>>Can you retest with 2.6.12.5 on 64bit so we can see if it is a new
>>problem?
>
>
> I hope that trying with 2.6.11, and getting the same problem (as I did in
> the meantime), is even better than testing 2.6.12.5.
Thanks, this is even more evidence for HW checksumming problems, these
existed for a long time.
>>So far I don't think its related to routed.
>
> The weird thing is that it works on tap, but not on ethernet/ppp. Maybe
> the kernel code gets some offset wrong?
Another sign pointing to HW checksumming ..
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Marc Lehmann @ 2005-09-07 21:34 UTC (permalink / raw)
To: Patrick McHardy; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <431EDF78.8060505@trash.net>
On Wed, Sep 07, 2005 at 02:39:20PM +0200, Patrick McHardy <kaber@trash.net> wrote:
> Please try if loading the ipt_LOG module and executing
> "echo 255 > /proc/sys/net/ipv4/netfilter/ip_conntrack_log_invalid"
> gives more information
Some more messages I get when logging is enabled:
printk: 1286 messages suppressed.
ip_ct_tcp: invalid state IN= OUT= SRC=84.56.231.206 DST=xxx.xxx.xxx.xxx LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=3260 DF PROTO=TCP SPT=41535 DPT=119 SEQ=3475818900 ACK=1819416201 WINDOW=12198 RES=0x00 ACK URGP=0 OPT (0101080A00F5DE260917B744) UID=0
printk: 1166 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxx.xxx.xxx.xxx DST=84.56.231.206 LEN=1492 TOS=0x00 PREC=0x00 TTL=53 ID=6652 DF PROTO=TCP SPT=119 DPT=41550 SEQ=686563106 ACK=3472571721 WINDOW=55741 RES=0x00 ACK URGP=0 OPT (0101080A091782AB00F5E2EC)
printk: 1114 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxx.xxx.xxx.xxx DST=84.56.231.206 LEN=52 TOS=0x00 PREC=0x00 TTL=53 ID=45484 DF PROTO=TCP SPT=119 DPT=41550 SEQ=686606959 ACK=3472571737 WINDOW=55725 RES=0x00 ACK URGP=0 OPT (0101080A0917849E00F5E7B4)
printk: 1214 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxx.xxx.xxx.xxx DST=84.56.231.206 LEN=1492 TOS=0x00 PREC=0x00 TTL=53 ID=39527 DF PROTO=TCP SPT=119 DPT=41552 SEQ=2432945453 ACK=3473246510 WINDOW=56283 RES=0x00 ACK URGP=0 OPT (0101080A09182B2000F5ECAC)
printk: 1320 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxx.xxx.xxx.xxx DST=84.56.231.206 LEN=1492 TOS=0x00 PREC=0x00 TTL=52 ID=4867 DF PROTO=TCP SPT=119 DPT=41561 SEQ=1077509261 ACK=3487524170 WINDOW=56319 RES=0x00 ACK URGP=0 OPT (0101080A0917ABCD00F5F18F)
printk: 1190 messages suppressed.
ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxx.xxx.xxx.xxx DST=84.56.231.206 LEN=1492 TOS=0x00 PREC=0x00 TTL=53 ID=7628 DF PROTO=TCP SPT=119 DPT=41538 SEQ=163747835 ACK=3477529327 WINDOW=56170 RES=0x00 ACK URGP=0 OPT (0101080A098F2AB200F5F682)
printk: 1172 messages suppressed.
The corresponding connections work just fine, though (and I think I get
more than a single message for every physical packet received).
--
The choice of a
-----==- _GNU_
----==-- _ generation Marc Lehmann
---==---(_)__ __ ____ __ pcg@goof.com
--==---/ / _ \/ // /\ \/ / http://schmorp.de/
-=====/_/_//_/\_,_/ /_/\_\ XX11-RIPE
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Patrick McHardy @ 2005-09-07 21:42 UTC (permalink / raw)
To: Marc Lehmann; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <20050907213413.GA8222@schmorp.de>
[-- Attachment #1: Type: text/plain, Size: 917 bytes --]
Marc Lehmann wrote:
> On Wed, Sep 07, 2005 at 02:39:20PM +0200, Patrick McHardy <kaber@trash.net> wrote:
>
>>Please try if loading the ipt_LOG module and executing
>>"echo 255 > /proc/sys/net/ipv4/netfilter/ip_conntrack_log_invalid"
>>gives more information
>
> Some more messages I get when logging is enabled:
>
> printk: 1286 messages suppressed.
> ip_ct_tcp: invalid state IN= OUT= SRC=84.56.231.206 DST=xxx.xxx.xxx.xxx LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=3260 DF PROTO=TCP SPT=41535 DPT=119 SEQ=3475818900 ACK=1819416201 WINDOW=12198 RES=0x00 ACK URGP=0 OPT (0101080A00F5DE260917B744) UID=0
> printk: 1166 messages suppressed.
This doesn't tell much since we don't know what happend to the
connection before. You can disable message surpressing by echoing
0 to /proc/sys/net/core/message_cost. I had a beer too much for
serious debugging, just to give some hints, does this patch make
the problem go away?
[-- Attachment #2: x --]
[-- Type: text/plain, Size: 443 bytes --]
diff --git a/net/ipv4/netfilter/ip_conntrack_proto_tcp.c b/net/ipv4/netfilter/ip_conntrack_proto_tcp.c
--- a/net/ipv4/netfilter/ip_conntrack_proto_tcp.c
+++ b/net/ipv4/netfilter/ip_conntrack_proto_tcp.c
@@ -843,7 +843,6 @@ static int tcp_error(struct sk_buff *skb
if (LOG_INVALID(IPPROTO_TCP))
nf_log_packet(PF_INET, 0, skb, NULL, NULL, NULL,
"ip_ct_tcp: bad TCP checksum ");
- return -NF_ACCEPT;
}
/* Check TCP flags. */
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Marc Lehmann @ 2005-09-07 21:52 UTC (permalink / raw)
To: Patrick McHardy; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <431F5CD2.8020905@trash.net>
On Wed, Sep 07, 2005 at 11:34:10PM +0200, Patrick McHardy <kaber@trash.net> wrote:
> > I think I have the LOG target compiled into the kernel. After the echo, I got
> > this within a matter of seconds:
> >
> > printk: 614 messages suppressed.
> > ip_ct_tcp: bad TCP checksum IN= OUT= SRC=xxxxxxxxxxxx DST=84.56.231.206 LEN=105 TOS=0x00 PREC=0x00 TTL=53 ID=33989 DF PROTO=TCP SPT=119 DPT=41349 SEQ=495763142 ACK=177548929 WINDOW=56677 RES=0x00 ACK PSH URGP=0 OPT (0101080A0986EF9D00E16123)
>
> Interesting .. if this isn't real there is most likely some problem with
> HW checksumming in netfilter. What does ethtool -k <dev> show?
It happens both with ppp(oe) as well as with ethernet, but the above message
originate son the ppp interface.
In any case, the ethtool output for eth1 (which is used by the pppoe
connection):
Offload parameters for eth1:
Cannot get device tcp segmentation offload settings: Operation not supported
rx-checksumming: on
tx-checksumming: on
scatter-gather: on
tcp segmentation offload: off
> > The weird thing is that it works on tap, but not on ethernet/ppp. Maybe
> > the kernel code gets some offset wrong?
>
> Another sign pointing to HW checksumming ..
It's also a 64-bit-only problem. To verify, I tried this:
ethtool -K eth1 rx off tx off sg off
Where eth1 is the interface where pppoe runs over.
ethtool -k eth1 then displayed:
rx-checksumming: off
tx-checksumming: off
scatter-gather: off
tcp segmentation offload: off
And ICMP, TCP etc. starts working again.
Thanks for the analysis and the hint, I guess that verifies that its hw
checksumming. (Weird that hw checksumming on the underlying device somehow
changes the ppp packets, but nevertheless).
If I can be of further assistance in tracking down this problem, please
rely on me. I can easily live with hw checksumming switched off on that
if, though.
--
The choice of a
-----==- _GNU_
----==-- _ generation Marc Lehmann
---==---(_)__ __ ____ __ pcg@goof.com
--==---/ / _ \/ // /\ \/ / http://schmorp.de/
-=====/_/_//_/\_,_/ /_/\_\ XX11-RIPE
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Marc Lehmann @ 2005-09-07 21:54 UTC (permalink / raw)
To: Patrick McHardy; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <431F5EA9.8020601@trash.net>
On Wed, Sep 07, 2005 at 11:42:01PM +0200, Patrick McHardy <kaber@trash.net> wrote:
> > Some more messages I get when logging is enabled:
> >
> > printk: 1286 messages suppressed.
> > ip_ct_tcp: invalid state IN= OUT= SRC=84.56.231.206 DST=xxx.xxx.xxx.xxx LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=3260 DF PROTO=TCP SPT=41535 DPT=119 SEQ=3475818900 ACK=1819416201 WINDOW=12198 RES=0x00 ACK URGP=0 OPT (0101080A00F5DE260917B744) UID=0
> > printk: 1166 messages suppressed.
>
> This doesn't tell much since we don't know what happend to the
> connection before. You can disable message surpressing by echoing
> 0 to /proc/sys/net/core/message_cost. I had a beer too much for
> serious debugging,
Well, as long as you can think of simple patches, that's just fine :)
> just to give some hints, does this patch make the problem go away?
I guess now that hw checksumming is identified as the direct cause, this is
no longer neecssary? If yes, just tell me and I'll try it out.
--
The choice of a
-----==- _GNU_
----==-- _ generation Marc Lehmann
---==---(_)__ __ ____ __ pcg@goof.com
--==---/ / _ \/ // /\ \/ / http://schmorp.de/
-=====/_/_//_/\_,_/ /_/\_\ XX11-RIPE
^ permalink raw reply
* Re: Fw: masquerading failure for at least icmp and tcp+sack on amd64
From: Patrick McHardy @ 2005-09-07 22:08 UTC (permalink / raw)
To: Marc Lehmann; +Cc: Andrew Morton, netdev, Netfilter Development Mailinglist
In-Reply-To: <20050907215407.GC8222@schmorp.de>
Marc Lehmann wrote:
> On Wed, Sep 07, 2005 at 11:42:01PM +0200, Patrick McHardy <kaber@trash.net> wrote:
>
>>just to give some hints, does this patch make the problem go away?
>
> I guess now that hw checksumming is identified as the direct cause, this is
> no longer neecssary? If yes, just tell me and I'll try it out.
No, don't bother. I'm goint to trying to figure out what's wrong, your
information so far should be enough, thanks. I'll let you know if I find
something worth trying.
^ permalink raw reply
* Re: [patch 1/1] ipw2100: remove by-hand function entry/exit debugging
From: Jeff Garzik @ 2005-09-08 0:52 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, akpm, pavel, ipw2100-admin, pavel, linux-kernel, netdev
In-Reply-To: <20050907.130151.71544363.davem@davemloft.net>
David S. Miller wrote:
> From: Ingo Oeser <netdev@axxeo.de>
> Date: Wed, 7 Sep 2005 15:39:08 +0200
>
>
>>Jeff Garzik wrote:
>>
>>>I find them useful in my own drivers; they are definitely not pure noise.
>>
>>gcc -finstrument-functions
>
>
> I was going to mention this as well, and also the idea to
> enable CONFIG_MCOUNT on a per-file basis.
>
> We should never be doing by hand what can be automated.
As long as nobody breaks the primary maintainer's primary method of
debugging, patches are welcome...
Jeff
^ permalink raw reply
* Git broken for IPW2200
From: Alejandro Bonilla Beeche @ 2005-09-08 1:41 UTC (permalink / raw)
To: netdev, Linus Torvalds; +Cc: ieee80211-devel, linux-kernel
Hi,
Where does one report this? I was building Linus Git tree as per I
updated it at 09/07/2005 7:00PM PDT and got this while compiling.
Where do I report this?
Debian unstable updated at same time.
it looks like ipw2200 is thinking that ieee80211 is not compiled in, but
I did select it as a module?
drivers/net/wireless/ipw2200.c:6676: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6677: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6679: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6679: error: 'WLAN_AUTH_SHARED_KEY'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:6686: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6686: error: 'SEC_ENABLED' undeclared
(first use in this function)
drivers/net/wireless/ipw2200.c:6687: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6689: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6691: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6697: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6697: error: 'SEC_LEVEL' undeclared
(first use in this function)
drivers/net/wireless/ipw2200.c:6698: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6699: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c: In function 'init_supported_rates':
drivers/net/wireless/ipw2200.c:6727: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6728: error: 'IEEE80211_52GHZ_BAND'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:6731: error: 'IEEE80211_CCK_MODULATION'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:6732: error:
'IEEE80211_OFDM_DEFAULT_RATES_MASK' undeclared (first use in this
function)
drivers/net/wireless/ipw2200.c:6739: error:
'IEEE80211_CCK_DEFAULT_RATES_MASK' undeclared (first use in this
function)
drivers/net/wireless/ipw2200.c:6740: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:6740: error: 'IEEE80211_OFDM_MODULATION'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c: In function 'ipw_net_init':
drivers/net/wireless/ipw2200.c:6887: warning: initialization makes
pointer from integer without a cast
drivers/net/wireless/ipw2200.c: In function 'ipw_pci_probe':
drivers/net/wireless/ipw2200.c:6970: warning: implicit declaration of
function 'alloc_ieee80211'
drivers/net/wireless/ipw2200.c:6970: warning: assignment makes pointer
from integer without a cast
drivers/net/wireless/ipw2200.c:6976: warning: assignment makes pointer
from integer without a cast
drivers/net/wireless/ipw2200.c:7060: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7069: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7078: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7079: error: 'IEEE80211_52GHZ_BAND'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:7079: error: 'IEEE80211_24GHZ_BAND'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:7080: error: 'IEEE80211_OFDM_MODULATION'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:7081: error: 'IEEE80211_CCK_MODULATION'
undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:7083: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_A' undeclared (first
use in this function)
drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_G' undeclared (first
use in this function)
drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_B' undeclared (first
use in this function)
drivers/net/wireless/ipw2200.c:7094: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7099: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7102: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7103: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7105: error:
'IEEE80211_DEFAULT_RATES_MASK' undeclared (first use in this function)
drivers/net/wireless/ipw2200.c:7126: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7127: error: dereferencing pointer to
incomplete type
drivers/net/wireless/ipw2200.c:7172: warning: implicit declaration of
function 'free_ieee80211'
make[4]: *** [drivers/net/wireless/ipw2200.o] Error 1
make[3]: *** [drivers/net/wireless] Error 2
make[2]: *** [drivers/net] Error 2
make[1]: *** [drivers] Error 2
make[1]: Leaving directory `/root/linux-2.6'
make: *** [stamp-build] Error 2
debian:~/linux-2.6#
.Alejandro
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Jeff Garzik @ 2005-09-08 1:49 UTC (permalink / raw)
To: Linux Kernel Mailing List; +Cc: Andrew Morton, Netdev List
In-Reply-To: <200509080125.j881PcL9015847@hera.kernel.org>
Linux Kernel Mailing List wrote:
> tree 1771b690cdee80312ace3fe046e29e965a0b30eb
> parent c8d127418d78aaeeb1a417ef7453dc09c9118146
> author Tommy S. Christensen <tommy.christensen@tpack.net> Wed, 07 Sep 2005 05:17:28 -0700
> committer Linus Torvalds <torvalds@g5.osdl.org> Thu, 08 Sep 2005 06:57:30 -0700
>
> [PATCH] 3c59x: read current link status from phy
>
> The phy status register must be read twice in order to get the actual link
> state.
>
> Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
> Signed-off-by: Andrew Morton <akpm@osdl.org>
> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
>
> drivers/net/3c59x.c | 1 +
> 1 files changed, 1 insertion(+)
>
> diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
> --- a/drivers/net/3c59x.c
> +++ b/drivers/net/3c59x.c
> @@ -1889,6 +1889,7 @@ vortex_timer(unsigned long data)
> {
> spin_lock_bh(&vp->lock);
> mii_status = mdio_read(dev, vp->phys[0], 1);
> + mii_status = mdio_read(dev, vp->phys[0], 1);
It would be nice if somebody would be motivated to check in
s/1/MII_BMSR/ to utilize the constant in include/linux/mii.h.
Jeff
^ permalink raw reply
* Re: Git broken for IPW2200
From: Jeff Garzik @ 2005-09-08 2:18 UTC (permalink / raw)
To: abonilla; +Cc: netdev, Linus Torvalds, ieee80211-devel, linux-kernel
In-Reply-To: <1126143695.5402.11.camel@localhost.localdomain>
Alejandro Bonilla Beeche wrote:
> Hi,
>
> Where does one report this? I was building Linus Git tree as per I
> updated it at 09/07/2005 7:00PM PDT and got this while compiling.
>
> Where do I report this?
>
> Debian unstable updated at same time.
>
> it looks like ipw2200 is thinking that ieee80211 is not compiled in, but
> I did select it as a module?
Wanna post a URL to your .config?
Jeff
^ permalink raw reply
* Re: Git broken for IPW2200
From: Alejandro Bonilla Beeche @ 2005-09-08 5:14 UTC (permalink / raw)
To: Jeff Garzik; +Cc: netdev, Linus Torvalds, ieee80211-devel, linux-kernel
In-Reply-To: <431F9F75.9020704@pobox.com>
[-- Attachment #1: Type: text/plain, Size: 287 bytes --]
On Wed, 2005-09-07 at 22:18 -0400, Jeff Garzik wrote:
> Alejandro Bonilla Beeche wrote:
>
> Wanna post a URL to your .config?
Jeff,
Sorry, I did not paste it in the ML because this has always worked for
me, but hell, maybe I got something wrong! :|
Attached...
.Alejandro
> Jeff
[-- Attachment #2: git-config --]
[-- Type: text/plain, Size: 53625 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13
# Wed Sep 7 19:10:08 2005
#
CONFIG_X86=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
CONFIG_MPENTIUMM=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
# CONFIG_SMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
# CONFIG_X86_MCE is not set
CONFIG_TOSHIBA=m
CONFIG_I8K=m
CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
#
# Firmware Drivers
#
CONFIG_EDD=m
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_MATH_EMULATION=y
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_HAVE_DEC_LOCK=y
# CONFIG_REGPARM is not set
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_PHYSICAL_START=0x100000
# CONFIG_KEXEC is not set
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_DEBUG=y
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION="/dev/hda3"
# CONFIG_SWSUSP_ENCRYPT is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_SLEEP_PROC_SLEEP=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_HOTKEY=y
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
# CONFIG_ACPI_IBM is not set
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
CONFIG_APM_REAL_MODE_POWER_OFF=y
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
#
# CPUFreq processor drivers
#
# CONFIG_X86_ACPI_CPUFREQ is not set
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
# CONFIG_X86_SPEEDSTEP_SMI is not set
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_PCI_MSI=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
CONFIG_PCI_DEBUG=y
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
CONFIG_MCA=y
CONFIG_MCA_LEGACY=y
# CONFIG_MCA_PROC_FS is not set
CONFIG_SCx200=m
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
# CONFIG_PCMCIA_LOAD_CIS is not set
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_TCIC=m
CONFIG_PCCARD_NONSTATIC=m
#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=m
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_COMPAQ=m
CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM=y
CONFIG_HOTPLUG_PCI_IBM=m
CONFIG_HOTPLUG_PCI_ACPI=m
# CONFIG_HOTPLUG_PCI_ACPI_IBM is not set
CONFIG_HOTPLUG_PCI_CPCI=y
CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m
CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m
CONFIG_HOTPLUG_PCI_SHPC=m
# CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_MULTIPATH_CACHED=y
CONFIG_IP_ROUTE_MULTIPATH_RR=y
CONFIG_IP_ROUTE_MULTIPATH_RANDOM=y
CONFIG_IP_ROUTE_MULTIPATH_WRANDOM=y
CONFIG_IP_ROUTE_MULTIPATH_DRR=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12
#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y
#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
# CONFIG_IP_NF_CONNTRACK_MARK is not set
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
# CONFIG_IP_NF_CT_PROTO_SCTP is not set
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_PHYSDEV=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_REALM=m
# CONFIG_IP_NF_MATCH_SCTP is not set
# CONFIG_IP_NF_MATCH_DCCP is not set
# CONFIG_IP_NF_MATCH_COMMENT is not set
# CONFIG_IP_NF_MATCH_HASHLIMIT is not set
# CONFIG_IP_NF_MATCH_STRING is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
# CONFIG_IP_NF_TARGET_TTL is not set
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_LIMIT=m
CONFIG_IP6_NF_MATCH_MAC=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_MULTIPORT=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_MARK=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AHESP=m
CONFIG_IP6_NF_MATCH_LENGTH=m
CONFIG_IP6_NF_MATCH_EUI64=m
# CONFIG_IP6_NF_MATCH_PHYSDEV is not set
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
# CONFIG_IP6_NF_TARGET_REJECT is not set
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_MARK=m
# CONFIG_IP6_NF_TARGET_HL is not set
CONFIG_IP6_NF_RAW=m
#
# DECnet: Netfilter Configuration
#
CONFIG_DECNET_NF_GRABULATOR=m
#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
# CONFIG_BRIDGE_EBT_ULOG is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
CONFIG_ATM=y
CONFIG_ATM_CLIP=y
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
CONFIG_ATM_MPOA=m
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
CONFIG_DECNET=m
# CONFIG_DECNET_ROUTER is not set
CONFIG_LLC=m
CONFIG_LLC2=m
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=y
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
CONFIG_X25=m
CONFIG_LAPB=m
# CONFIG_NET_DIVERT is not set
CONFIG_ECONET=m
CONFIG_ECONET_AUNUDP=y
CONFIG_ECONET_NATIVE=y
CONFIG_WAN_ROUTER=m
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=y
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
# CONFIG_NET_CLS_IND is not set
# CONFIG_CLS_U32_MARK is not set
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=y
CONFIG_NET_EMATCH_NBYTE=y
CONFIG_NET_EMATCH_U32=y
CONFIG_NET_EMATCH_META=y
# CONFIG_NET_EMATCH_TEXT is not set
# CONFIG_NET_CLS_ACT is not set
CONFIG_NET_CLS_POLICE=y
#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_HAMRADIO=y
#
# Packet Radio protocols
#
CONFIG_AX25=m
# CONFIG_AX25_DAMA_SLAVE is not set
CONFIG_NETROM=m
CONFIG_ROSE=m
#
# AX.25 network device drivers
#
CONFIG_MKISS=m
CONFIG_6PACK=m
CONFIG_BPQETHER=m
CONFIG_BAYCOM_SER_FDX=m
CONFIG_BAYCOM_SER_HDX=m
CONFIG_YAM=m
CONFIG_IRDA=m
#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set
#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y
#
# Infrared-port device drivers
#
#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m
#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
CONFIG_LITELINK_DONGLE=m
CONFIG_MA600_DONGLE=m
CONFIG_GIRBIL_DONGLE=m
CONFIG_MCP2120_DONGLE=m
CONFIG_OLD_BELKIN_DONGLE=m
CONFIG_ACT200L_DONGLE=m
#
# Old SIR device drivers
#
CONFIG_IRPORT_SIR=m
#
# Old Serial dongle support
#
# CONFIG_DONGLE_OLD is not set
#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_SIGMATEL_FIR=m
# CONFIG_NSC_FIR is not set
# CONFIG_WINBOND_FIR is not set
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
# CONFIG_ALI_FIR is not set
CONFIG_VLSI_FIR=m
# CONFIG_VIA_FIR is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
# CONFIG_BT_HCIUART_BCSP_TXCRC is not set
CONFIG_BT_HCIBCM203X=m
# CONFIG_BT_HCIBPA10X is not set
CONFIG_BT_HCIBFUSB=m
# CONFIG_BT_HCIDTL1 is not set
# CONFIG_BT_HCIBT3C is not set
# CONFIG_BT_HCIBLUECARD is not set
# CONFIG_BT_HCIBTUART is not set
CONFIG_BT_HCIVHCI=m
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
CONFIG_DEBUG_DRIVER=y
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_INFTL=m
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_AMDSTD_RETRY=0
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m
# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PHYSMAP_START=0x8000000
CONFIG_MTD_PHYSMAP_LEN=0x4000000
CONFIG_MTD_PHYSMAP_BANKWIDTH=2
CONFIG_MTD_PNC2000=m
CONFIG_MTD_SC520CDP=m
CONFIG_MTD_NETSC520=m
# CONFIG_MTD_TS5500 is not set
CONFIG_MTD_SBC_GXX=m
CONFIG_MTD_SCx200_DOCFLASH=m
# CONFIG_MTD_AMD76XROM is not set
# CONFIG_MTD_ICHXROM is not set
# CONFIG_MTD_SCB2_FLASH is not set
CONFIG_MTD_NETtel=m
CONFIG_MTD_DILNETPC=m
CONFIG_MTD_DILNETPC_BOOTSIZE=0x80000
# CONFIG_MTD_L440GX is not set
CONFIG_MTD_PCI=m
# CONFIG_MTD_PCMCIA is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
CONFIG_MTD_PMC551=m
# CONFIG_MTD_PMC551_BUGFIX is not set
# CONFIG_MTD_PMC551_DEBUG is not set
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLKMTD=m
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOC2000=m
CONFIG_MTD_DOC2001=m
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
# CONFIG_MTD_DOCPROBE_ADVANCED is not set
CONFIG_MTD_DOCPROBE_ADDRESS=0
#
# NAND Flash Device Drivers
#
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_DISKONCHIP=m
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
CONFIG_PNP=y
CONFIG_PNP_DEBUG=y
#
# Protocols
#
CONFIG_PNPACPI=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_PS2=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_LBD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=y
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_OPTI621=m
CONFIG_BLK_DEV_RZ1000=m
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_ATIIXP=y
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
CONFIG_BLK_DEV_SC1200=y
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT821X is not set
CONFIG_BLK_DEV_NS87415=y
CONFIG_BLK_DEV_PDC202XX_OLD=y
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
# CONFIG_PDC202XX_FORCE is not set
CONFIG_BLK_DEV_SVWKS=y
CONFIG_BLK_DEV_SIIMAGE=y
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
# CONFIG_SCSI_ISCSI_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_FD_MCS is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IBMMCA is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR_D700 is not set
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
# CONFIG_SCSI_NCR_Q720 is not set
# CONFIG_SCSI_MCA_53C9X is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
CONFIG_SCSI_DEBUG=y
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
# CONFIG_BLK_DEV_DM is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
# Device Drivers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m
#
# I2O device support
#
CONFIG_I2O=m
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
# CONFIG_I2O_BUS is not set
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=m
# CONFIG_E1000_NAPI is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m
#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set
#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_IPW2100 is not set
# CONFIG_IPW_DEBUG is not set
CONFIG_IPW2200=m
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_AIRO_CS=m
# CONFIG_PCMCIA_WL3501 is not set
#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
CONFIG_HOSTAP=m
# CONFIG_HOSTAP_FIRMWARE is not set
# CONFIG_HOSTAP_PLX is not set
# CONFIG_HOSTAP_PCI is not set
# CONFIG_HOSTAP_CS is not set
CONFIG_NET_WIRELESS=y
#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
# CONFIG_PCMCIA_3C589 is not set
# CONFIG_PCMCIA_3C574 is not set
# CONFIG_PCMCIA_FMVJ18X is not set
# CONFIG_PCMCIA_PCNET is not set
# CONFIG_PCMCIA_NMCLAN is not set
# CONFIG_PCMCIA_SMC91C92 is not set
CONFIG_PCMCIA_XIRC2PS=m
# CONFIG_PCMCIA_AXNET is not set
#
# Wan interfaces
#
CONFIG_WAN=y
CONFIG_DSCC4=m
CONFIG_DSCC4_PCISYNC=y
CONFIG_DSCC4_PCI_RST=y
CONFIG_LANMEDIA=m
CONFIG_SYNCLINK_SYNCPPP=m
CONFIG_HDLC=m
CONFIG_HDLC_RAW=y
CONFIG_HDLC_RAW_ETH=y
CONFIG_HDLC_CISCO=y
CONFIG_HDLC_FR=y
CONFIG_HDLC_PPP=y
CONFIG_HDLC_X25=y
CONFIG_PCI200SYN=m
CONFIG_WANXL=m
CONFIG_PC300=m
CONFIG_PC300_MLPPP=y
CONFIG_FARSYNC=m
CONFIG_DLCI=m
CONFIG_DLCI_COUNT=24
CONFIG_DLCI_MAX=8
CONFIG_WAN_ROUTER_DRIVERS=y
# CONFIG_VENDOR_SANGOMA is not set
CONFIG_CYCLADES_SYNC=m
CONFIG_CYCLOMX_X25=y
CONFIG_LAPBETHER=m
CONFIG_X25_ASY=m
CONFIG_SBNI=m
# CONFIG_SBNI_MULTILINE is not set
#
# ATM drivers
#
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
CONFIG_ATM_ZATM=m
# CONFIG_ATM_ZATM_DEBUG is not set
CONFIG_ATM_NICSTAR=m
# CONFIG_ATM_NICSTAR_USE_SUNI is not set
# CONFIG_ATM_NICSTAR_USE_IDT77105 is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
CONFIG_ATM_IA=m
# CONFIG_ATM_IA_DEBUG is not set
CONFIG_ATM_FORE200E_MAYBE=m
CONFIG_ATM_FORE200E_PCA=y
CONFIG_ATM_FORE200E_PCA_DEFAULT_FW=y
# CONFIG_ATM_FORE200E_USE_TASKLET is not set
CONFIG_ATM_FORE200E_TX_RETRY=16
CONFIG_ATM_FORE200E_DEBUG=0
CONFIG_ATM_FORE200E=m
CONFIG_ATM_HE=m
CONFIG_ATM_HE_USE_SUNI=y
CONFIG_FDDI=y
CONFIG_DEFXX=m
CONFIG_SKFP=m
CONFIG_HIPPI=y
# CONFIG_ROADRUNNER is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
CONFIG_NET_FC=y
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
CONFIG_NETPOLL_RX=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
CONFIG_PHONE_IXJ_PCMCIA=m
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_TSDEV=m
CONFIG_INPUT_TSDEV_SCREEN_X=240
CONFIG_INPUT_TSDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_SUNKBD=m
CONFIG_KEYBOARD_LKKBD=m
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_VSXXXAA=m
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_UINPUT=m
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PCIPS2=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_COMPUTONE=m
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
CONFIG_DIGIEPCA=m
CONFIG_MOXA_INTELLIO=m
CONFIG_MOXA_SMARTIO=m
# CONFIG_ISI is not set
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_N_HDLC=m
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
CONFIG_SX=m
CONFIG_RIO=m
CONFIG_RIO_OLDPCI=y
CONFIG_STALDRV=y
CONFIG_STALLION=m
CONFIG_ISTALLION=m
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_CS=m
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
# CONFIG_SERIAL_8250_MCA is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# IPMI
#
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
# CONFIG_IPMI_POWEROFF is not set
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC520_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_WAFER_WDT=m
CONFIG_I8XX_TCO=m
CONFIG_SC1200_WDT=m
CONFIG_SCx200_WDT=m
CONFIG_60XX_WDT=m
CONFIG_CPU5_WDT=m
CONFIG_W83627HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_MACHZ_WDT=m
#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y
#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_HW_RANDOM=m
CONFIG_NVRAM=m
CONFIG_RTC=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
CONFIG_DTLK=m
CONFIG_R3964=m
CONFIG_APPLICOM=m
CONFIG_SONYPI=m
#
# Ftape, the floppy tape device driver
#
CONFIG_FTAPE=m
CONFIG_ZFTAPE=m
CONFIG_ZFT_DFLT_BLK_SZ=10240
#
# The compressor will be built as a module only!
#
CONFIG_ZFT_COMPRESSOR=m
CONFIG_FT_NR_BUFFERS=3
CONFIG_FT_PROC_FS=y
CONFIG_FT_NORMAL_DEBUG=y
# CONFIG_FT_FULL_DEBUG is not set
# CONFIG_FT_NO_TRACE is not set
# CONFIG_FT_NO_TRACE_AT_ALL is not set
#
# Hardware configuration
#
CONFIG_FT_STD_FDC=y
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not set
CONFIG_FT_FDC_THR=8
CONFIG_FT_FDC_MAX_RATE=2000
CONFIG_FT_ALPHA_CLOCK=0
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
CONFIG_AGP_ATI=y
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=m
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=m
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
# CONFIG_MWAVE is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HPET is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# TPM devices
#
CONFIG_TCG_TPM=y
# CONFIG_TCG_NSC is not set
# CONFIG_TCG_ATMEL is not set
# CONFIG_TCG_INFINEON is not set
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
# CONFIG_I2C_AMD756_S4882 is not set
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
# CONFIG_I2C_STUB is not set
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
# CONFIG_SENSORS_PCA9539 is not set
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_RTC8564=m
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# Dallas's 1-wire bus
#
CONFIG_W1=m
CONFIG_W1_MATROX=m
# CONFIG_W1_DS9490 is not set
CONFIG_W1_THERM=m
# CONFIG_W1_SMEM is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
# CONFIG_SENSORS_ADM1026 is not set
CONFIG_SENSORS_ADM1031=m
# CONFIG_SENSORS_ADM9240 is not set
CONFIG_SENSORS_ASB100=m
# CONFIG_SENSORS_ATXP1 is not set
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_FSCHER=m
# CONFIG_SENSORS_FSCPOS is not set
CONFIG_SENSORS_GL518SM=m
# CONFIG_SENSORS_GL520SM is not set
CONFIG_SENSORS_IT87=m
# CONFIG_SENSORS_LM63 is not set
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
# CONFIG_SENSORS_LM87 is not set
CONFIG_SENSORS_LM90=m
# CONFIG_SENSORS_LM92 is not set
CONFIG_SENSORS_MAX1619=m
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_W83781D=m
# CONFIG_SENSORS_W83792D is not set
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
CONFIG_IBM_ASM=m
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
#
# Video For Linux
#
#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
# CONFIG_VIDEO_ZR36120 is not set
CONFIG_VIDEO_MEYE=m
CONFIG_VIDEO_SAA7134=m
# CONFIG_VIDEO_SAA7134_DVB is not set
CONFIG_VIDEO_MXB=m
CONFIG_VIDEO_DPC=m
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88=m
# CONFIG_VIDEO_CX88_DVB is not set
CONFIG_VIDEO_OVCAMCHIP=m
#
# Radio Adapters
#
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
#
# Digital Video Broadcasting Devices
#
CONFIG_DVB=y
CONFIG_DVB_CORE=m
#
# Supported SAA7146 based PCI Adapters
#
CONFIG_DVB_AV7110=m
CONFIG_DVB_AV7110_OSD=y
CONFIG_DVB_BUDGET=m
CONFIG_DVB_BUDGET_CI=m
CONFIG_DVB_BUDGET_AV=m
CONFIG_DVB_BUDGET_PATCH=m
#
# Supported USB Adapters
#
# CONFIG_DVB_USB is not set
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
# CONFIG_DVB_CINERGYT2 is not set
#
# Supported FlexCopII (B2C2) Adapters
#
# CONFIG_DVB_B2C2_FLEXCOP is not set
#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m
#
# Supported Pluto2 Adapters
#
# CONFIG_DVB_PLUTO2 is not set
#
# Supported DVB Frontends
#
#
# Customise DVB Frontends
#
#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
CONFIG_DVB_TDA8083=m
# CONFIG_DVB_TDA80XX is not set
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m
#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
# CONFIG_DVB_CX22702 is not set
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
# CONFIG_DVB_DIB3000MB is not set
# CONFIG_DVB_DIB3000MC is not set
#
# DVB-C (cable) frontends
#
CONFIG_DVB_ATMEL_AT76C651=m
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_STV0297=m
#
# ATSC (North American/Korean Terresterial DTV) frontends
#
CONFIG_DVB_NXT2002=m
CONFIG_DVB_OR51211=m
# CONFIG_DVB_OR51132 is not set
# CONFIG_DVB_BCM3510 is not set
# CONFIG_DVB_LGDT330X is not set
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_VIDEOBUF=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SOFT_CURSOR=y
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON_OLD=m
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=m
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_DEVICE=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# PCMCIA devices
#
#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
CONFIG_SOUND_ICH=m
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_FORTE is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_AD1980 is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
# CONFIG_USB_SL811_CS is not set
#
# USB Device Class drivers
#
CONFIG_USB_AUDIO=m
#
# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
#
CONFIG_USB_MIDI=m
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
# CONFIG_USB_STORAGE_USBAT is not set
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
# CONFIG_USB_ACECAD is not set
CONFIG_USB_KBTAB=m
CONFIG_USB_POWERMATE=m
CONFIG_USB_MTOUCH=m
# CONFIG_USB_ITMTOUCH is not set
CONFIG_USB_EGALAX=m
CONFIG_USB_XPAD=m
CONFIG_USB_ATI_REMOTE=m
# CONFIG_USB_KEYSPAN_REMOTE is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set
# CONFIG_USB_W9968CF is not set
# CONFIG_USB_PWC is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_AIRPRIME is not set
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
# CONFIG_USB_SERIAL_CP2101 is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_HP4X is not set
CONFIG_USB_SERIAL_SAFE=m
# CONFIG_USB_SERIAL_SAFE_PADDED is not set
# CONFIG_USB_SERIAL_TI is not set
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
# CONFIG_USB_SERIAL_OPTION is not set
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
CONFIG_USB_IDMOUSE=y
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
CONFIG_USB_TEST=m
#
# USB DSL modem support
#
# CONFIG_USB_ATM is not set
#
# USB Gadget Support
#
CONFIG_USB_GADGET=m
# CONFIG_USB_GADGET_DEBUG_FILES is not set
CONFIG_USB_GADGET_SELECTED=y
CONFIG_USB_GADGET_NET2280=y
CONFIG_USB_NET2280=m
# CONFIG_USB_GADGET_PXA2XX is not set
# CONFIG_USB_GADGET_GOKU is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
# CONFIG_USB_FILE_STORAGE_TEST is not set
CONFIG_USB_G_SERIAL=m
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=y
CONFIG_JBD_DEBUG=y
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_CHECK=y
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
# CONFIG_REISERFS_FS_POSIX_ACL is not set
# CONFIG_REISERFS_FS_SECURITY is not set
CONFIG_JFS_FS=y
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
#
# XFS support
#
CONFIG_XFS_FS=y
CONFIG_XFS_EXPORT=y
CONFIG_XFS_RT=y
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
#
CONFIG_ADFS_FS=m
# CONFIG_ADFS_FS_RW is not set
CONFIG_AFFS_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
CONFIG_EFS_FS=m
CONFIG_JFFS_FS=m
CONFIG_JFFS_FS_VERBOSE=0
CONFIG_JFFS_PROC_FS=y
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
CONFIG_VXFS_FS=m
CONFIG_HPFS_FS=m
CONFIG_QNX4FS_FS=m
# CONFIG_QNX4FS_RW is not set
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
# CONFIG_NCPFS_SMALLDOS is not set
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
CONFIG_AFS_FS=m
CONFIG_RXRPC=m
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
CONFIG_ACORN_PARTITION=y
CONFIG_ACORN_PARTITION_CUMANA=y
# CONFIG_ACORN_PARTITION_EESOX is not set
CONFIG_ACORN_PARTITION_ICS=y
# CONFIG_ACORN_PARTITION_ADFS is not set
# CONFIG_ACORN_PARTITION_POWERTEC is not set
CONFIG_ACORN_PARTITION_RISCIX=y
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
CONFIG_ATARI_PARTITION=y
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
CONFIG_SGI_PARTITION=y
CONFIG_ULTRIX_PARTITION=y
CONFIG_SUN_PARTITION=y
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Profiling support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DETECT_SOFTLOCKUP is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_KPROBES is not set
# CONFIG_DEBUG_STACK_USAGE is not set
#
# Page alloc debug is incompatible with Software Suspend on i386
#
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
CONFIG_SECURITY=y
# CONFIG_SECURITY_NETWORK is not set
CONFIG_SECURITY_CAPABILITIES=m
CONFIG_SECURITY_ROOTPLUG=m
# CONFIG_SECURITY_SECLVL is not set
# CONFIG_SECURITY_SELINUX is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=y
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_KHAZAD=m
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_TEST=m
#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set
#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
^ permalink raw reply
* [PATCH 2.6.13] pcnet32: set_ringparam implementation
From: Hubert WS Lin @ 2005-09-08 7:27 UTC (permalink / raw)
To: netdev; +Cc: linux-kernel, fubar, donf, jklewis
[-- Attachment #1: Type: text/plain, Size: 362 bytes --]
Hi,
This patch implements the set_ringparam(), one of the ethtool
operations, which allows changing tx/rx ring sizes via ethtool.
Changelog:
- Changed memery allocation of tx/rx ring from static to dynamic
- Implemented set_ringparam()
- Tested on i386 and ppc64
Signed-off-by: Hubert WS Lin <wslin@tw.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
[-- Attachment #2: pcnet32-set_ringparam.diff --]
[-- Type: text/x-patch, Size: 19567 bytes --]
--- a/drivers/net/pcnet32.c 2005-09-02 15:06:30.000000000 +0800
+++ b/drivers/net/pcnet32.c 2005-09-02 15:58:06.000000000 +0800
@@ -22,8 +22,8 @@
*************************************************************************/
#define DRV_NAME "pcnet32"
-#define DRV_VERSION "1.30j"
-#define DRV_RELDATE "29.04.2005"
+#define DRV_VERSION "1.31"
+#define DRV_RELDATE "02.Sep.2005"
#define PFX DRV_NAME ": "
static const char *version =
@@ -257,6 +257,7 @@ static int homepna[MAX_UNITS];
* v1.30h 24 Jun 2004 Don Fry correctly select auto, speed, duplex in bcr32.
* v1.30i 28 Jun 2004 Don Fry change to use module_param.
* v1.30j 29 Apr 2005 Don Fry fix skb/map leak with loopback test.
+ * v1.31 02 Sep 2005 Hubert WS Lin <wslin@tw.ibm.c0m> added set_ringparam().
*/
@@ -266,17 +267,17 @@ static int homepna[MAX_UNITS];
* That translates to 2 (4 == 2^^2) and 4 (16 == 2^^4).
*/
#ifndef PCNET32_LOG_TX_BUFFERS
-#define PCNET32_LOG_TX_BUFFERS 4
-#define PCNET32_LOG_RX_BUFFERS 5
+#define PCNET32_LOG_TX_BUFFERS 4
+#define PCNET32_LOG_RX_BUFFERS 5
+#define PCNET32_LOG_MAX_TX_BUFFERS 9 /* 2^9 == 512 */
+#define PCNET32_LOG_MAX_RX_BUFFERS 9
#endif
#define TX_RING_SIZE (1 << (PCNET32_LOG_TX_BUFFERS))
-#define TX_RING_MOD_MASK (TX_RING_SIZE - 1)
-#define TX_RING_LEN_BITS ((PCNET32_LOG_TX_BUFFERS) << 12)
+#define TX_MAX_RING_SIZE (1 << (PCNET32_LOG_MAX_TX_BUFFERS))
#define RX_RING_SIZE (1 << (PCNET32_LOG_RX_BUFFERS))
-#define RX_RING_MOD_MASK (RX_RING_SIZE - 1)
-#define RX_RING_LEN_BITS ((PCNET32_LOG_RX_BUFFERS) << 4)
+#define RX_MAX_RING_SIZE (1 << (PCNET32_LOG_MAX_RX_BUFFERS))
#define PKT_BUF_SZ 1544
@@ -339,8 +340,8 @@ struct pcnet32_access {
*/
struct pcnet32_private {
/* The Tx and Rx ring entries must be aligned on 16-byte boundaries in 32bit mode. */
- struct pcnet32_rx_head rx_ring[RX_RING_SIZE];
- struct pcnet32_tx_head tx_ring[TX_RING_SIZE];
+ struct pcnet32_rx_head *rx_ring;
+ struct pcnet32_tx_head *tx_ring;
struct pcnet32_init_block init_block;
dma_addr_t dma_addr; /* DMA address of beginning of this
object, returned by
@@ -349,13 +350,21 @@ struct pcnet32_private {
structure */
const char *name;
/* The saved address of a sent-in-place packet/buffer, for skfree(). */
- struct sk_buff *tx_skbuff[TX_RING_SIZE];
- struct sk_buff *rx_skbuff[RX_RING_SIZE];
- dma_addr_t tx_dma_addr[TX_RING_SIZE];
- dma_addr_t rx_dma_addr[RX_RING_SIZE];
+ struct sk_buff **tx_skbuff;
+ struct sk_buff **rx_skbuff;
+ dma_addr_t *tx_dma_addr;
+ dma_addr_t *rx_dma_addr;
struct pcnet32_access a;
spinlock_t lock; /* Guard lock */
unsigned int cur_rx, cur_tx; /* The next free ring entry */
+ unsigned int rx_ring_size; /* current rx ring size */
+ unsigned int tx_ring_size; /* current tx ring size */
+ unsigned int rx_mod_mask; /* rx ring modular mask */
+ unsigned int tx_mod_mask; /* tx ring modular mask */
+ unsigned short rx_len_bits;
+ unsigned short tx_len_bits;
+ dma_addr_t rx_ring_dma_addr;
+ dma_addr_t tx_ring_dma_addr;
unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */
struct net_device_stats stats;
char tx_full;
@@ -397,6 +406,9 @@ static int pcnet32_get_regs_len(struct n
static void pcnet32_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *ptr);
static void pcnet32_purge_tx_ring(struct net_device *dev);
+static int pcnet32_alloc_ring(struct net_device *dev);
+static void pcnet32_free_ring(struct net_device *dev);
+
enum pci_flags_bit {
PCI_USES_IO=1, PCI_USES_MEM=2, PCI_USES_MASTER=4,
@@ -613,10 +625,59 @@ static void pcnet32_get_ringparam(struct
{
struct pcnet32_private *lp = dev->priv;
- ering->tx_max_pending = TX_RING_SIZE - 1;
- ering->tx_pending = lp->cur_tx - lp->dirty_tx;
- ering->rx_max_pending = RX_RING_SIZE - 1;
- ering->rx_pending = lp->cur_rx & RX_RING_MOD_MASK;
+ ering->tx_max_pending = TX_MAX_RING_SIZE - 1;
+ ering->tx_pending = lp->tx_ring_size - 1;
+ ering->rx_max_pending = RX_MAX_RING_SIZE - 1;
+ ering->rx_pending = lp->rx_ring_size - 1;
+}
+
+static int pcnet32_set_ringparam(struct net_device *dev, struct ethtool_ringparam *ering)
+{
+ struct pcnet32_private *lp = dev->priv;
+ unsigned long flags;
+ int i;
+
+ if (ering->rx_mini_pending || ering->rx_jumbo_pending)
+ return -EINVAL;
+
+ if (netif_running(dev))
+ pcnet32_close(dev);
+
+ spin_lock_irqsave(&lp->lock, flags);
+ pcnet32_free_ring(dev);
+ lp->tx_ring_size = min(ering->tx_pending, (unsigned int) TX_MAX_RING_SIZE);
+ lp->rx_ring_size = min(ering->rx_pending, (unsigned int) RX_MAX_RING_SIZE);
+
+ for (i = 0; i <= PCNET32_LOG_MAX_TX_BUFFERS; i++) {
+ if (lp->tx_ring_size <= (1 << i))
+ break;
+ }
+ lp->tx_ring_size = (1 << i);
+ lp->tx_mod_mask = lp->tx_ring_size - 1;
+ lp->tx_len_bits = (i << 12);
+
+ for (i = 0; i <= PCNET32_LOG_MAX_RX_BUFFERS; i++) {
+ if (lp->rx_ring_size <= (1 << i))
+ break;
+ }
+ lp->rx_ring_size = (1 << i);
+ lp->rx_mod_mask = lp->rx_ring_size - 1;
+ lp->rx_len_bits = (i << 4);
+
+ if (pcnet32_alloc_ring(dev)) {
+ pcnet32_free_ring(dev);
+ return -ENOMEM;
+ }
+
+ spin_unlock_irqrestore(&lp->lock, flags);
+
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_INFO PFX "Ring Param Settings: RX: %d, TX: %d\n", lp->rx_ring_size, lp->tx_ring_size);
+
+ if (netif_running(dev))
+ pcnet32_open(dev);
+
+ return 0;
}
static void pcnet32_get_strings(struct net_device *dev, u32 stringset, u8 *data)
@@ -948,6 +1009,7 @@ static struct ethtool_ops pcnet32_ethtoo
.nway_reset = pcnet32_nway_reset,
.get_link = pcnet32_get_link,
.get_ringparam = pcnet32_get_ringparam,
+ .set_ringparam = pcnet32_set_ringparam,
.get_tx_csum = ethtool_op_get_tx_csum,
.get_sg = ethtool_op_get_sg,
.get_tso = ethtool_op_get_tso,
@@ -1239,6 +1301,12 @@ pcnet32_probe1(unsigned long ioaddr, int
dev->priv = lp;
lp->name = chipname;
lp->shared_irq = shared;
+ lp->tx_ring_size = TX_RING_SIZE; /* default tx ring size */
+ lp->rx_ring_size = RX_RING_SIZE; /* default rx ring size */
+ lp->tx_mod_mask = lp->tx_ring_size - 1;
+ lp->rx_mod_mask = lp->rx_ring_size - 1;
+ lp->tx_len_bits = (PCNET32_LOG_TX_BUFFERS << 12);
+ lp->rx_len_bits = (PCNET32_LOG_RX_BUFFERS << 4);
lp->mii_if.full_duplex = fdx;
lp->mii_if.phy_id_mask = 0x1f;
lp->mii_if.reg_num_mask = 0x1f;
@@ -1265,21 +1333,23 @@ pcnet32_probe1(unsigned long ioaddr, int
}
lp->a = *a;
+ if (pcnet32_alloc_ring(dev)) {
+ ret = -ENOMEM;
+ goto err_free_ring;
+ }
/* detect special T1/E1 WAN card by checking for MAC address */
if (dev->dev_addr[0] == 0x00 && dev->dev_addr[1] == 0xe0
&& dev->dev_addr[2] == 0x75)
lp->options = PCNET32_PORT_FD | PCNET32_PORT_GPSI;
lp->init_block.mode = le16_to_cpu(0x0003); /* Disable Rx and Tx. */
- lp->init_block.tlen_rlen = le16_to_cpu(TX_RING_LEN_BITS | RX_RING_LEN_BITS);
+ lp->init_block.tlen_rlen = le16_to_cpu(lp->tx_len_bits | lp->rx_len_bits);
for (i = 0; i < 6; i++)
lp->init_block.phys_addr[i] = dev->dev_addr[i];
lp->init_block.filter[0] = 0x00000000;
lp->init_block.filter[1] = 0x00000000;
- lp->init_block.rx_ring = (u32)le32_to_cpu(lp->dma_addr +
- offsetof(struct pcnet32_private, rx_ring));
- lp->init_block.tx_ring = (u32)le32_to_cpu(lp->dma_addr +
- offsetof(struct pcnet32_private, tx_ring));
+ lp->init_block.rx_ring = (u32)le32_to_cpu(lp->rx_ring_dma_addr);
+ lp->init_block.tx_ring = (u32)le32_to_cpu(lp->tx_ring_dma_addr);
/* switch pcnet32 to 32bit mode */
a->write_bcr(ioaddr, 20, 2);
@@ -1310,7 +1380,7 @@ pcnet32_probe1(unsigned long ioaddr, int
if (pcnet32_debug & NETIF_MSG_PROBE)
printk(", failed to detect IRQ line.\n");
ret = -ENODEV;
- goto err_free_consistent;
+ goto err_free_ring;
}
if (pcnet32_debug & NETIF_MSG_PROBE)
printk(", probed IRQ %d.\n", dev->irq);
@@ -1341,7 +1411,7 @@ pcnet32_probe1(unsigned long ioaddr, int
/* Fill in the generic fields of the device structure. */
if (register_netdev(dev))
- goto err_free_consistent;
+ goto err_free_ring;
if (pdev) {
pci_set_drvdata(pdev, dev);
@@ -1359,6 +1429,8 @@ pcnet32_probe1(unsigned long ioaddr, int
return 0;
+err_free_ring:
+ pcnet32_free_ring(dev);
err_free_consistent:
pci_free_consistent(lp->pci_dev, sizeof(*lp), lp, lp->dma_addr);
err_free_netdev:
@@ -1369,6 +1441,94 @@ err_release_region:
}
+static int pcnet32_alloc_ring(struct net_device *dev)
+{
+ struct pcnet32_private *lp = dev->priv;
+
+ if ((lp->tx_ring = pci_alloc_consistent(lp->pci_dev, sizeof(struct pcnet32_tx_head) * lp->tx_ring_size,
+ &lp->tx_ring_dma_addr)) == NULL) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Consistent memory allocation failed.\n");
+ return -ENOMEM;
+ }
+
+ if ((lp->rx_ring = pci_alloc_consistent(lp->pci_dev, sizeof(struct pcnet32_rx_head) * lp->rx_ring_size,
+ &lp->rx_ring_dma_addr)) == NULL) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Consistent memory allocation failed.\n");
+ return -ENOMEM;
+ }
+
+ if (!(lp->tx_dma_addr = kmalloc(sizeof(dma_addr_t) * lp->tx_ring_size, GFP_ATOMIC))) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Memory allocation failed.\n");
+ return -ENOMEM;
+ }
+ memset(lp->tx_dma_addr, 0, sizeof(dma_addr_t) * lp->tx_ring_size);
+
+ if (!(lp->rx_dma_addr = kmalloc(sizeof(dma_addr_t) * lp->rx_ring_size, GFP_ATOMIC))) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Memory allocation failed.\n");
+ return -ENOMEM;
+ }
+ memset(lp->rx_dma_addr, 0, sizeof(dma_addr_t) * lp->rx_ring_size);
+
+ if (!(lp->tx_skbuff = kmalloc(sizeof(struct sk_buff *) * lp->tx_ring_size, GFP_ATOMIC))) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Memory allocation failed.\n");
+ return -ENOMEM;
+ }
+ memset(lp->tx_skbuff, 0, sizeof(struct sk_buff *) * lp->tx_ring_size);
+
+ if (!(lp->rx_skbuff = kmalloc(sizeof(struct sk_buff *) * lp->rx_ring_size, GFP_ATOMIC))) {
+ if (pcnet32_debug & NETIF_MSG_DRV)
+ printk(KERN_ERR PFX "Memory allocation failed.\n");
+ return -ENOMEM;
+ }
+ memset(lp->rx_skbuff, 0, sizeof(struct sk_buff *) * lp->rx_ring_size);
+
+ return 0;
+}
+
+
+static void pcnet32_free_ring(struct net_device *dev)
+{
+ struct pcnet32_private *lp = dev->priv;
+
+ if (lp->tx_skbuff) {
+ kfree(lp->tx_skbuff);
+ lp->tx_skbuff = NULL;
+ }
+
+ if (lp->rx_skbuff) {
+ kfree(lp->rx_skbuff);
+ lp->rx_skbuff = NULL;
+ }
+
+ if (lp->tx_dma_addr) {
+ kfree(lp->tx_dma_addr);
+ lp->tx_dma_addr = NULL;
+ }
+
+ if (lp->rx_dma_addr) {
+ kfree(lp->rx_dma_addr);
+ lp->rx_dma_addr = NULL;
+ }
+
+ if (lp->tx_ring) {
+ pci_free_consistent(lp->pci_dev, sizeof(struct pcnet32_tx_head) * lp->tx_ring_size,
+ lp->tx_ring, lp->tx_ring_dma_addr);
+ lp->tx_ring = NULL;
+ }
+
+ if (lp->rx_ring) {
+ pci_free_consistent(lp->pci_dev, sizeof(struct pcnet32_rx_head) * lp->rx_ring_size,
+ lp->rx_ring, lp->rx_ring_dma_addr);
+ lp->rx_ring = NULL;
+ }
+}
+
+
static int
pcnet32_open(struct net_device *dev)
{
@@ -1400,8 +1560,8 @@ pcnet32_open(struct net_device *dev)
if (netif_msg_ifup(lp))
printk(KERN_DEBUG "%s: pcnet32_open() irq %d tx/rx rings %#x/%#x init %#x.\n",
dev->name, dev->irq,
- (u32) (lp->dma_addr + offsetof(struct pcnet32_private, tx_ring)),
- (u32) (lp->dma_addr + offsetof(struct pcnet32_private, rx_ring)),
+ (u32) (lp->tx_ring_dma_addr),
+ (u32) (lp->rx_ring_dma_addr),
(u32) (lp->dma_addr + offsetof(struct pcnet32_private, init_block)));
/* set/reset autoselect bit */
@@ -1521,7 +1681,7 @@ pcnet32_open(struct net_device *dev)
err_free_ring:
/* free any allocated skbuffs */
- for (i = 0; i < RX_RING_SIZE; i++) {
+ for (i = 0; i < lp->rx_ring_size; i++) {
lp->rx_ring[i].status = 0;
if (lp->rx_skbuff[i]) {
pci_unmap_single(lp->pci_dev, lp->rx_dma_addr[i], PKT_BUF_SZ-2,
@@ -1531,6 +1691,9 @@ err_free_ring:
lp->rx_skbuff[i] = NULL;
lp->rx_dma_addr[i] = 0;
}
+
+ pcnet32_free_ring(dev);
+
/*
* Switch back to 16bit mode to avoid problems with dumb
* DOS packet driver after a warm reboot
@@ -1562,7 +1725,7 @@ pcnet32_purge_tx_ring(struct net_device
struct pcnet32_private *lp = dev->priv;
int i;
- for (i = 0; i < TX_RING_SIZE; i++) {
+ for (i = 0; i < lp->tx_ring_size; i++) {
lp->tx_ring[i].status = 0; /* CPU owns buffer */
wmb(); /* Make sure adapter sees owner change */
if (lp->tx_skbuff[i]) {
@@ -1587,7 +1750,7 @@ pcnet32_init_ring(struct net_device *dev
lp->cur_rx = lp->cur_tx = 0;
lp->dirty_rx = lp->dirty_tx = 0;
- for (i = 0; i < RX_RING_SIZE; i++) {
+ for (i = 0; i < lp->rx_ring_size; i++) {
struct sk_buff *rx_skbuff = lp->rx_skbuff[i];
if (rx_skbuff == NULL) {
if (!(rx_skbuff = lp->rx_skbuff[i] = dev_alloc_skb (PKT_BUF_SZ))) {
@@ -1611,20 +1774,18 @@ pcnet32_init_ring(struct net_device *dev
}
/* The Tx buffer address is filled in as needed, but we do need to clear
* the upper ownership bit. */
- for (i = 0; i < TX_RING_SIZE; i++) {
+ for (i = 0; i < lp->tx_ring_size; i++) {
lp->tx_ring[i].status = 0; /* CPU owns buffer */
wmb(); /* Make sure adapter sees owner change */
lp->tx_ring[i].base = 0;
lp->tx_dma_addr[i] = 0;
}
- lp->init_block.tlen_rlen = le16_to_cpu(TX_RING_LEN_BITS | RX_RING_LEN_BITS);
+ lp->init_block.tlen_rlen = le16_to_cpu(lp->tx_len_bits | lp->rx_len_bits);
for (i = 0; i < 6; i++)
lp->init_block.phys_addr[i] = dev->dev_addr[i];
- lp->init_block.rx_ring = (u32)le32_to_cpu(lp->dma_addr +
- offsetof(struct pcnet32_private, rx_ring));
- lp->init_block.tx_ring = (u32)le32_to_cpu(lp->dma_addr +
- offsetof(struct pcnet32_private, tx_ring));
+ lp->init_block.rx_ring = (u32)le32_to_cpu(lp->rx_ring_dma_addr);
+ lp->init_block.tx_ring = (u32)le32_to_cpu(lp->tx_ring_dma_addr);
wmb(); /* Make sure all changes are visible */
return 0;
}
@@ -1682,13 +1843,13 @@ pcnet32_tx_timeout (struct net_device *d
printk(KERN_DEBUG " Ring data dump: dirty_tx %d cur_tx %d%s cur_rx %d.",
lp->dirty_tx, lp->cur_tx, lp->tx_full ? " (full)" : "",
lp->cur_rx);
- for (i = 0 ; i < RX_RING_SIZE; i++)
+ for (i = 0 ; i < lp->rx_ring_size; i++)
printk("%s %08x %04x %08x %04x", i & 1 ? "" : "\n ",
le32_to_cpu(lp->rx_ring[i].base),
(-le16_to_cpu(lp->rx_ring[i].buf_length)) & 0xffff,
le32_to_cpu(lp->rx_ring[i].msg_length),
le16_to_cpu(lp->rx_ring[i].status));
- for (i = 0 ; i < TX_RING_SIZE; i++)
+ for (i = 0 ; i < lp->tx_ring_size; i++)
printk("%s %08x %04x %08x %04x", i & 1 ? "" : "\n ",
le32_to_cpu(lp->tx_ring[i].base),
(-le16_to_cpu(lp->tx_ring[i].length)) & 0xffff,
@@ -1729,7 +1890,7 @@ pcnet32_start_xmit(struct sk_buff *skb,
/* Fill in a Tx ring entry */
/* Mask to ring buffer boundary. */
- entry = lp->cur_tx & TX_RING_MOD_MASK;
+ entry = lp->cur_tx & lp->tx_mod_mask;
/* Caution: the write order is important here, set the status
* with the "ownership" bits last. */
@@ -1753,7 +1914,7 @@ pcnet32_start_xmit(struct sk_buff *skb,
dev->trans_start = jiffies;
- if (lp->tx_ring[(entry+1) & TX_RING_MOD_MASK].base != 0) {
+ if (lp->tx_ring[(entry+1) & lp->tx_mod_mask].base != 0) {
lp->tx_full = 1;
netif_stop_queue(dev);
}
@@ -1806,7 +1967,7 @@ pcnet32_interrupt(int irq, void *dev_id,
int delta;
while (dirty_tx != lp->cur_tx) {
- int entry = dirty_tx & TX_RING_MOD_MASK;
+ int entry = dirty_tx & lp->tx_mod_mask;
int status = (short)le16_to_cpu(lp->tx_ring[entry].status);
if (status < 0)
@@ -1864,18 +2025,18 @@ pcnet32_interrupt(int irq, void *dev_id,
dirty_tx++;
}
- delta = (lp->cur_tx - dirty_tx) & (TX_RING_MOD_MASK + TX_RING_SIZE);
- if (delta > TX_RING_SIZE) {
+ delta = (lp->cur_tx - dirty_tx) & (lp->tx_mod_mask + lp->tx_ring_size);
+ if (delta > lp->tx_ring_size) {
if (netif_msg_drv(lp))
printk(KERN_ERR "%s: out-of-sync dirty pointer, %d vs. %d, full=%d.\n",
dev->name, dirty_tx, lp->cur_tx, lp->tx_full);
- dirty_tx += TX_RING_SIZE;
- delta -= TX_RING_SIZE;
+ dirty_tx += lp->tx_ring_size;
+ delta -= lp->tx_ring_size;
}
if (lp->tx_full &&
netif_queue_stopped(dev) &&
- delta < TX_RING_SIZE - 2) {
+ delta < lp->tx_ring_size - 2) {
/* The ring is no longer full, clear tbusy. */
lp->tx_full = 0;
netif_wake_queue (dev);
@@ -1932,8 +2093,8 @@ static int
pcnet32_rx(struct net_device *dev)
{
struct pcnet32_private *lp = dev->priv;
- int entry = lp->cur_rx & RX_RING_MOD_MASK;
- int boguscnt = RX_RING_SIZE / 2;
+ int entry = lp->cur_rx & lp->rx_mod_mask;
+ int boguscnt = lp->rx_ring_size / 2;
/* If we own the next entry, it's a new packet. Send it up. */
while ((short)le16_to_cpu(lp->rx_ring[entry].status) >= 0) {
@@ -1998,12 +2159,12 @@ pcnet32_rx(struct net_device *dev)
if (netif_msg_drv(lp))
printk(KERN_ERR "%s: Memory squeeze, deferring packet.\n",
dev->name);
- for (i = 0; i < RX_RING_SIZE; i++)
+ for (i = 0; i < lp->rx_ring_size; i++)
if ((short)le16_to_cpu(lp->rx_ring[(entry+i)
- & RX_RING_MOD_MASK].status) < 0)
+ & lp->rx_mod_mask].status) < 0)
break;
- if (i > RX_RING_SIZE -2) {
+ if (i > lp->rx_ring_size -2) {
lp->stats.rx_dropped++;
lp->rx_ring[entry].status |= le16_to_cpu(0x8000);
wmb(); /* Make sure adapter sees owner change */
@@ -2041,7 +2202,7 @@ pcnet32_rx(struct net_device *dev)
lp->rx_ring[entry].buf_length = le16_to_cpu(2-PKT_BUF_SZ);
wmb(); /* Make sure owner changes after all others are visible */
lp->rx_ring[entry].status |= le16_to_cpu(0x8000);
- entry = (++lp->cur_rx) & RX_RING_MOD_MASK;
+ entry = (++lp->cur_rx) & lp->rx_mod_mask;
if (--boguscnt <= 0) break; /* don't stay in loop forever */
}
@@ -2084,7 +2245,7 @@ pcnet32_close(struct net_device *dev)
spin_lock_irqsave(&lp->lock, flags);
/* free all allocated skbuffs */
- for (i = 0; i < RX_RING_SIZE; i++) {
+ for (i = 0; i < lp->rx_ring_size; i++) {
lp->rx_ring[i].status = 0;
wmb(); /* Make sure adapter sees owner change */
if (lp->rx_skbuff[i]) {
@@ -2096,7 +2257,7 @@ pcnet32_close(struct net_device *dev)
lp->rx_dma_addr[i] = 0;
}
- for (i = 0; i < TX_RING_SIZE; i++) {
+ for (i = 0; i < lp->tx_ring_size; i++) {
lp->tx_ring[i].status = 0; /* CPU owns buffer */
wmb(); /* Make sure adapter sees owner change */
if (lp->tx_skbuff[i]) {
@@ -2265,6 +2426,7 @@ static void __devexit pcnet32_remove_one
struct pcnet32_private *lp = dev->priv;
unregister_netdev(dev);
+ pcnet32_free_ring(dev);
release_region(dev->base_addr, PCNET32_TOTAL_SIZE);
pci_free_consistent(lp->pci_dev, sizeof(*lp), lp, lp->dma_addr);
free_netdev(dev);
@@ -2340,6 +2502,7 @@ static void __exit pcnet32_cleanup_modul
struct pcnet32_private *lp = pcnet32_dev->priv;
next_dev = lp->next;
unregister_netdev(pcnet32_dev);
+ pcnet32_free_ring(pcnet32_dev);
release_region(pcnet32_dev->base_addr, PCNET32_TOTAL_SIZE);
pci_free_consistent(lp->pci_dev, sizeof(*lp), lp, lp->dma_addr);
free_netdev(pcnet32_dev);
^ permalink raw reply
* Re: IPW2100 Kconfig
From: Pavel Machek @ 2005-09-08 8:01 UTC (permalink / raw)
To: Alejandro Bonilla; +Cc: netdev, linux-kernel
In-Reply-To: <005101c5b311_4ca69a50_a20cc60a@amer.sykes.com>
Hi!
> I checked the IPW2100 in the current git from linux-2.6 and the menuconfig
> help (Kconfig) says you need to put the firmware in /etc/firmware, it should
> be /lib/firmware.
>
> Who should I send the "patch" to? Or can someone simply change that?
Are you sure it is not distro-dependend?
--
64 bytes from 195.113.31.123: icmp_seq=28 ttl=51 time=448769.1 ms
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Bogdan Costescu @ 2005-09-08 11:58 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Linux Kernel Mailing List, Andrew Morton, Netdev List
In-Reply-To: <431F9899.4060602@pobox.com>
On Wed, 7 Sep 2005, Jeff Garzik wrote:
>> The phy status register must be read twice in order to get the actual link
>> state.
Can the original poster give an explanation ? I've enjoyed a rather
well functioning 3c59x driver for the past ~6 years without such
double reading. Plus:
- this operation is I/O expensive
- it is performed inside a region protected by a spinlock
- it is performed often, every 60 seconds
Is there some specific hardware that exhibits a problem that is solved
by this double reading ?
--
Bogdan Costescu
IWR - Interdisziplinaeres Zentrum fuer Wissenschaftliches Rechnen
Universitaet Heidelberg, INF 368, D-69120 Heidelberg, GERMANY
Telephone: +49 6221 54 8869, Telefax: +49 6221 54 8868
E-mail: Bogdan.Costescu@IWR.Uni-Heidelberg.De
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Tommy Christensen @ 2005-09-08 13:05 UTC (permalink / raw)
To: Bogdan Costescu
Cc: Jeff Garzik, Linux Kernel Mailing List, Andrew Morton,
Netdev List
In-Reply-To: <Pine.LNX.4.63.0509081351160.21354@dingo.iwr.uni-heidelberg.de>
On Thu, 2005-09-08 at 13:58, Bogdan Costescu wrote:
> Can the original poster give an explanation ? I've enjoyed a rather
> well functioning 3c59x driver for the past ~6 years without such
> double reading. Plus:
> - this operation is I/O expensive
> - it is performed inside a region protected by a spinlock
> - it is performed often, every 60 seconds
>
> Is there some specific hardware that exhibits a problem that is solved
> by this double reading ?
Nothing critical. The idea is to avoid an extra delay of 60 seconds
before detecting link-up.
Please see http://bugzilla.kernel.org/show_bug.cgi?id=5025
-Tommy
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Bogdan Costescu @ 2005-09-08 13:35 UTC (permalink / raw)
To: Tommy Christensen
Cc: Jeff Garzik, Linux Kernel Mailing List, Andrew Morton,
Netdev List
In-Reply-To: <1126184700.4805.32.camel@tsc-6.cph.tpack.net>
On Thu, 8 Sep 2005, Tommy Christensen wrote:
> The idea is to avoid an extra delay of 60 seconds before detecting
> link-up.
But you are adding the read to a function that is called repeatedly to
fix an event that happens only once at start-up !
If this read is really needed (I still doubt it...), can't it be
performed in vortex_up(), by possibly doubling the existing one there ?
vortex_up() is executed only once at start-up, not every 60 seconds.
> Please see http://bugzilla.kernel.org/show_bug.cgi?id=5025
Hah, a Cisco switch. Look in Documentation/networking/vortex.txt for
"portfast".
--
Bogdan Costescu
IWR - Interdisziplinaeres Zentrum fuer Wissenschaftliches Rechnen
Universitaet Heidelberg, INF 368, D-69120 Heidelberg, GERMANY
Telephone: +49 6221 54 8869, Telefax: +49 6221 54 8868
E-mail: Bogdan.Costescu@IWR.Uni-Heidelberg.De
^ permalink raw reply
* Re: [PATCH] 3c59x: cleanup of mdio_read routines to use MII_* macros in include/linux/mii.h
From: Neil Horman @ 2005-09-08 14:13 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Linux Kernel Mailing List, Andrew Morton, Netdev List
In-Reply-To: <431F9899.4060602@pobox.com>
On Wed, Sep 07, 2005 at 09:49:13PM -0400, Jeff Garzik wrote:
><snip>
> It would be nice if somebody would be motivated to check in
> s/1/MII_BMSR/ to utilize the constant in include/linux/mii.h.
>
> Jeff
>
As requested, a patch to cleanup mdio_read routines in 3c59x.c to use the MII_*
macros defined in include/linux/mii.h
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
3c59x.c | 14 +++++++-------
1 files changed, 7 insertions(+), 7 deletions(-)
--- linux-2.6/drivers/net/3c59x.c.orig 2005-09-08 08:24:35.000000000 -0400
+++ linux-2.6/drivers/net/3c59x.c 2005-09-08 08:27:57.000000000 -0400
@@ -1439,7 +1439,7 @@ static int __devinit vortex_probe1(struc
if (vp->drv_flags & EXTRA_PREAMBLE)
mii_preamble_required++;
mdio_sync(ioaddr, 32);
- mdio_read(dev, 24, 1);
+ mdio_read(dev, 24, MII_BMSR);
for (phy = 0; phy < 32 && phy_idx < 1; phy++) {
int mii_status, phyx;
@@ -1453,7 +1453,7 @@ static int __devinit vortex_probe1(struc
phyx = phy - 1;
else
phyx = phy;
- mii_status = mdio_read(dev, phyx, 1);
+ mii_status = mdio_read(dev, phyx, MII_BMSR);
if (mii_status && mii_status != 0xffff) {
vp->phys[phy_idx++] = phyx;
if (print_info) {
@@ -1469,7 +1469,7 @@ static int __devinit vortex_probe1(struc
printk(KERN_WARNING" ***WARNING*** No MII transceivers found!\n");
vp->phys[0] = 24;
} else {
- vp->advertising = mdio_read(dev, vp->phys[0], 4);
+ vp->advertising = mdio_read(dev, vp->phys[0], MII_ADVERTISE);
if (vp->full_duplex) {
/* Only advertise the FD media types. */
vp->advertising &= ~0x02A0;
@@ -1641,8 +1641,8 @@ vortex_up(struct net_device *dev)
int mii_reg1, mii_reg5;
EL3WINDOW(4);
/* Read BMSR (reg1) only to clear old status. */
- mii_reg1 = mdio_read(dev, vp->phys[0], 1);
- mii_reg5 = mdio_read(dev, vp->phys[0], 5);
+ mii_reg1 = mdio_read(dev, vp->phys[0], MII_BMSR);
+ mii_reg5 = mdio_read(dev, vp->phys[0], MII_LPA);
if (mii_reg5 == 0xffff || mii_reg5 == 0x0000) {
netif_carrier_off(dev); /* No MII device or no link partner report */
} else {
@@ -1872,13 +1872,13 @@ vortex_timer(unsigned long data)
case XCVR_MII: case XCVR_NWAY:
{
spin_lock_bh(&vp->lock);
- mii_status = mdio_read(dev, vp->phys[0], 1);
+ mii_status = mdio_read(dev, vp->phys[0], MII_BMSR);
ok = 1;
if (vortex_debug > 2)
printk(KERN_DEBUG "%s: MII transceiver has status %4.4x.\n",
dev->name, mii_status);
if (mii_status & BMSR_LSTATUS) {
- int mii_reg5 = mdio_read(dev, vp->phys[0], 5);
+ int mii_reg5 = mdio_read(dev, vp->phys[0], MII_LPA);
if (! vp->force_fd && mii_reg5 != 0xffff) {
int duplex;
--
/***************************************************
*Neil Horman
*Software Engineer
*gpg keyid: 1024D / 0x92A74FA1 - http://pgp.mit.edu
***************************************************/
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Tommy Christensen @ 2005-09-08 14:42 UTC (permalink / raw)
To: Bogdan Costescu
Cc: Jeff Garzik, Linux Kernel Mailing List, Andrew Morton,
Netdev List
In-Reply-To: <Pine.LNX.4.63.0509081521140.21354@dingo.iwr.uni-heidelberg.de>
On Thu, 2005-09-08 at 15:35, Bogdan Costescu wrote:
> On Thu, 8 Sep 2005, Tommy Christensen wrote:
>
> > The idea is to avoid an extra delay of 60 seconds before detecting
> > link-up.
>
> But you are adding the read to a function that is called repeatedly to
> fix an event that happens only once at start-up !
Link state can change anytime, not just at start-up. That's why
it's being repeatedly monitored ;-)
> If this read is really needed (I still doubt it...), can't it be
> performed in vortex_up(), by possibly doubling the existing one there ?
> vortex_up() is executed only once at start-up, not every 60 seconds.
That won't solve the reported issue, unfortunately.
Besides, how long would you like to wait for network connectivity
after plugging in the cable? It is now lowered from [60-120] to
[0-60] seconds.
Personally, I'd prefer the delay to be < 10 seconds.
-Tommy
^ permalink raw reply
* Re: Git broken for IPW2200
From: Joe Bob Spamtest @ 2005-09-08 15:25 UTC (permalink / raw)
To: abonilla; +Cc: netdev, ieee80211-devel, linux-kernel
In-Reply-To: <1126143695.5402.11.camel@localhost.localdomain>
IPW2200 requires a different ieee80211 stack, this can be had at
ieee80211.sourceforge.net
Alejandro Bonilla Beeche wrote:
> Hi,
>
> Where does one report this? I was building Linus Git tree as per I
> updated it at 09/07/2005 7:00PM PDT and got this while compiling.
>
> Where do I report this?
>
> Debian unstable updated at same time.
>
> it looks like ipw2200 is thinking that ieee80211 is not compiled in, but
> I did select it as a module?
>
> drivers/net/wireless/ipw2200.c:6676: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6677: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6679: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6679: error: 'WLAN_AUTH_SHARED_KEY'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:6686: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6686: error: 'SEC_ENABLED' undeclared
> (first use in this function)
> drivers/net/wireless/ipw2200.c:6687: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6689: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6691: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6697: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6697: error: 'SEC_LEVEL' undeclared
> (first use in this function)
> drivers/net/wireless/ipw2200.c:6698: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6699: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c: In function 'init_supported_rates':
> drivers/net/wireless/ipw2200.c:6727: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6728: error: 'IEEE80211_52GHZ_BAND'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:6731: error: 'IEEE80211_CCK_MODULATION'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:6732: error:
> 'IEEE80211_OFDM_DEFAULT_RATES_MASK' undeclared (first use in this
> function)
> drivers/net/wireless/ipw2200.c:6739: error:
> 'IEEE80211_CCK_DEFAULT_RATES_MASK' undeclared (first use in this
> function)
> drivers/net/wireless/ipw2200.c:6740: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:6740: error: 'IEEE80211_OFDM_MODULATION'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c: In function 'ipw_net_init':
> drivers/net/wireless/ipw2200.c:6887: warning: initialization makes
> pointer from integer without a cast
> drivers/net/wireless/ipw2200.c: In function 'ipw_pci_probe':
> drivers/net/wireless/ipw2200.c:6970: warning: implicit declaration of
> function 'alloc_ieee80211'
> drivers/net/wireless/ipw2200.c:6970: warning: assignment makes pointer
> from integer without a cast
> drivers/net/wireless/ipw2200.c:6976: warning: assignment makes pointer
> from integer without a cast
> drivers/net/wireless/ipw2200.c:7060: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7069: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7078: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7079: error: 'IEEE80211_52GHZ_BAND'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:7079: error: 'IEEE80211_24GHZ_BAND'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:7080: error: 'IEEE80211_OFDM_MODULATION'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:7081: error: 'IEEE80211_CCK_MODULATION'
> undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:7083: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_A' undeclared (first
> use in this function)
> drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_G' undeclared (first
> use in this function)
> drivers/net/wireless/ipw2200.c:7083: error: 'IEEE_B' undeclared (first
> use in this function)
> drivers/net/wireless/ipw2200.c:7094: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7099: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7102: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7103: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7105: error:
> 'IEEE80211_DEFAULT_RATES_MASK' undeclared (first use in this function)
> drivers/net/wireless/ipw2200.c:7126: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7127: error: dereferencing pointer to
> incomplete type
> drivers/net/wireless/ipw2200.c:7172: warning: implicit declaration of
> function 'free_ieee80211'
> make[4]: *** [drivers/net/wireless/ipw2200.o] Error 1
> make[3]: *** [drivers/net/wireless] Error 2
> make[2]: *** [drivers/net] Error 2
> make[1]: *** [drivers] Error 2
> make[1]: Leaving directory `/root/linux-2.6'
> make: *** [stamp-build] Error 2
> debian:~/linux-2.6#
>
> .Alejandro
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
>
> ------------------------------------------------------------------------
>
> --
> / This message has been classified as *non-spam*.
> Mark this message as spam.
> <mailto:spam@spamtest.viacore.net?Subject=09072005183846-20792&body=Click
> the send button to mark this message as spam.>
>
> Thank you for using the crm114 Spam Control System. /
^ permalink raw reply
* Re: 2.6.13-git7 strange system freeze
From: Michal Piotrowski @ 2005-09-08 15:38 UTC (permalink / raw)
To: LKML; +Cc: netdev, akpm
In-Reply-To: <6bffcb0e050908051412e945c9@mail.gmail.com>
Hi,
kernel: 2.6.13-mm2
it happens when I try to download new gnome-2.12 livecd from bittorrent.
ng02:/home/michal# tail /var/log/kern.log
[..]
Sep 8 17:15:39 ng02 kernel: [ 3241.479108] KERNEL: assertion
((int)tp->lost_out >= 0) failed at net/ipv4/tcp_input.c (2148)
Sep 8 17:15:39 ng02 kernel: [ 3241.479192] KERNEL: assertion
((int)tp->lost_out >= 0) failed at net/ipv4/tcp_input.c (1127)
Sep 8 17:15:39 ng02 kernel: [ 3241.479736] KERNEL: assertion
((int)tp->lost_out >= 0) failed at net/ipv4/tcp_input.c (1127)
Sep 8 17:15:39 ng02 kernel: [ 3241.831114] KERNEL: assertion
((int)tp->lost_out >= 0) failed at net/ipv4/tcp_input.c (2148)
Sep 8 17:15:40 ng02 kernel: [ 3242.103942] KERNEL: assertion
((int)tp->lost_out >= 0) failed at net/ipv4/tcp_input.c (2148)
Sep 8 17:15:40 ng02 kernel: [ 3242.103951] Leak l=4294967295 3
Regards,
Michal Piotrowski
^ permalink raw reply
* Re: [PATCH] 3c59x: read current link status from phy
From: Bogdan Costescu @ 2005-09-08 15:42 UTC (permalink / raw)
To: Tommy Christensen
Cc: Jeff Garzik, Linux Kernel Mailing List, Andrew Morton,
Netdev List
In-Reply-To: <1126190554.4805.68.camel@tsc-6.cph.tpack.net>
On Thu, 8 Sep 2005, Tommy Christensen wrote:
> Besides, how long would you like to wait for network connectivity
> after plugging in the cable? It is now lowered from [60-120] to
> [0-60] seconds.
I now understood what the problem was, so I'll put it in words for
posterity: the Link Status bit of the MII Status register needs to be
read twice to first clear the error state (link bit=0) after which the
bit reports the actual value of the link. From the manual:
This bit has a latching function. A link failure causes the
bit to clear and remain clear until it has been read through
the management interface.
I tested this on a Tornado chip and it works as advertised (after link
is back up, first read gives 0x7829, the second 0x782d).
But I still don't agree with your solution: you are reading the Status
register twice in all cases, which is wrong. What you want is to read
it a second time only after the link was marked as down: a simple
check if bit 2 of the Status register is 0, in which case you issue
the second read. This still means that there will be 2 reads if the
link remains down, but at least there is only 1 read for the case
where the link is up and remains up.
> Personally, I'd prefer the delay to be < 10 seconds.
If you sample every 60 seconds ? Teach Shannon how to do it ;-)
If you mean to reduce the sampling period, there is a very good reason
not to do it: these MDIO operations are expensive - it's a serial
protocol. vortex_timer() might do 2 (and with the discussed change -
3) of them - there are better things to do for the CPU than wait for
these I/O operations. Plus, vortex_timer() also disables the
interrupt...
The Tornado and at least some Cyclone chips support generating an
interrupt whenever the link changes, which can be used instead of
polling for link state. This feature is not used in the 3c59x driver
and could give you much less than 10 seconds accuracy - but you have
to code it. ;-)
--
Bogdan Costescu
IWR - Interdisziplinaeres Zentrum fuer Wissenschaftliches Rechnen
Universitaet Heidelberg, INF 368, D-69120 Heidelberg, GERMANY
Telephone: +49 6221 54 8869, Telefax: +49 6221 54 8868
E-mail: Bogdan.Costescu@IWR.Uni-Heidelberg.De
^ permalink raw reply
* RE: Git broken for IPW2200
From: Alejandro Bonilla @ 2005-09-08 15:45 UTC (permalink / raw)
To: 'Joe Bob Spamtest'
Cc: netdev, ieee80211-devel, 'linux-kernel'
In-Reply-To: <432057D6.3010208@spamtest.viacore.net>
> IPW2200 requires a different ieee80211 stack, this can be had at
> ieee80211.sourceforge.net
Joe,
The stack is already in mainline in Linus Git. I should not need to
download the ieee80211 from any place but compile with the one in the
kernel.
.Alejandro
>
>
> Alejandro Bonilla Beeche wrote:
> > Hi,
> >
> > Where does one report this? I was building Linus Git
> tree as per I
> > updated it at 09/07/2005 7:00PM PDT and got this while compiling.
> >
> > Where do I report this?
> >
> > Debian unstable updated at same time.
> >
> > it looks like ipw2200 is thinking that ieee80211 is not
> compiled in, but
> > I did select it as a module?
> >
> > drivers/net/wireless/ipw2200.c:6676: error: dereferencing pointer to
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox