* Re: [PATCH] davinci_emac.c: Fix IFF_ALLMULTI setup
From: David Miller @ 2013-10-21 22:57 UTC (permalink / raw)
To: mceier+kernel
Cc: mugunthanvnm, prabhakar.csengg, jg1.han, jiri, netdev,
linux-kernel
In-Reply-To: <1382377504-24688-1-git-send-email-mceier+kernel@gmail.com>
From: Mariusz Ceier <mceier+kernel@gmail.com>
Date: Mon, 21 Oct 2013 19:45:04 +0200
> When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
> emac_dev_mcast_set should only enable RX of multicasts and reset
> MACHASH registers.
>
> It does this, but afterwards it either sets up multicast MACs
> filtering or disables RX of multicasts and resets MACHASH registers
> again, rendering IFF_ALLMULTI flag useless.
>
> This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
> disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
>
> Tested with kernel 2.6.37.
>
> Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Applied and queued up for -stable, thanks.
^ permalink raw reply
* Re: [PATCH net] ipv6: probe routes asynchronous in rt6_probe
From: David Miller @ 2013-10-21 22:57 UTC (permalink / raw)
To: hannes; +Cc: netdev, ja
In-Reply-To: <20131021041715.GH27787@order.stressinduktion.org>
From: Hannes Frederic Sowa <hannes@stressinduktion.org>
Date: Mon, 21 Oct 2013 06:17:15 +0200
> Routes need to be probed asynchronous otherwise the call stack gets
> exhausted when the kernel attemps to deliver another skb inline, like
> e.g. xt_TEE does, and we probe at the same time.
>
> We update neigh->updated still at once, otherwise we would send to
> many probes.
>
> Cc: Julian Anastasov <ja@ssi.bg>
> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Looks good, applied and queued up for -stable, thanks Hannes.
^ permalink raw reply
* Re: [PATCH 1/1] [PATCH] ax88179_178a: Correct the RX error definition in RX header
From: David Miller @ 2013-10-21 22:55 UTC (permalink / raw)
To: freddy; +Cc: linux-usb, linux-kernel, netdev, louis, allan
In-Reply-To: <1382337460-2036-1-git-send-email-freddy@asix.com.tw>
From: freddy@asix.com.tw
Date: Mon, 21 Oct 2013 14:37:40 +0800
> From: Freddy Xin <freddy@asix.com.tw>
>
> Correct the definition of AX_RXHDR_CRC_ERR and
> AX_RXHDR_DROP_ERR. They are BIT29 and BIT31 in pkt_hdr
> seperately.
> Add VID:DID for Samsung USB Ethernet Adapter.
>
> Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Do not do two logically different things in one patch.
Fix the register bit definitions in one patch, then add the
new device IDs in another.
^ permalink raw reply
* Re: [PATCH net-next 0/3] ipv6: sit: Implement TSO/GSO support
From: David Miller @ 2013-10-21 22:50 UTC (permalink / raw)
To: edumazet; +Cc: netdev, hkchu, eilong, ek, therbert
In-Reply-To: <1382327251-21079-1-git-send-email-edumazet@google.com>
From: Eric Dumazet <edumazet@google.com>
Date: Sun, 20 Oct 2013 20:47:28 -0700
> This patch serie implements GSO/TSO support for SIT tunnels
Looks good, thanks for the descriptive cover posting it helps
a lot.
All applied to net-next.
^ permalink raw reply
* Re: [PATCH v2] chelsio: remove duplicate defines
From: David Miller @ 2013-10-21 22:47 UTC (permalink / raw)
To: michael.opdenacker; +Cc: divy, netdev, linux-kernel
In-Reply-To: <1382332189-5596-1-git-send-email-michael.opdenacker@free-electrons.com>
From: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Date: Mon, 21 Oct 2013 07:09:49 +0200
> This removes multiple duplicate definitions
> in drivers/net/ethernet/chelsio/cxgb3/regs.h
>
> Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Applied.
^ permalink raw reply
* Re: [PATCH] atm: firestream: remove duplicate define
From: David Miller @ 2013-10-21 22:47 UTC (permalink / raw)
To: chas; +Cc: michael.opdenacker, linux-atm-general, netdev, linux-kernel
In-Reply-To: <20131021075335.5c9e4490@thirdoffive.cmf.nrl.navy.mil>
From: chas williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Date: Mon, 21 Oct 2013 07:53:35 -0400
> Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
>
> On Mon, 21 Oct 2013 10:12:41 +0200
> Michael Opdenacker <michael.opdenacker@free-electrons.com> wrote:
>
>> This patch removes a duplicate define in drivers/atm/firestream.h
>>
>> Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Applied.
^ permalink raw reply
* Re: [PATCH] ethernet: moxa: remove duplicate includes
From: David Miller @ 2013-10-21 22:47 UTC (permalink / raw)
To: michael.opdenacker; +Cc: netdev, linux-kernel
In-Reply-To: <1382246036-19253-1-git-send-email-michael.opdenacker@free-electrons.com>
From: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Date: Sun, 20 Oct 2013 07:13:56 +0200
> Reported by "make includecheck"
>
> Tested that drivers/net/ethernet/moxa/moxart_ether.c still compiles
> well on ARM
>
> Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Applied.
^ permalink raw reply
* Re: [PATCH] cgxb4: remove duplicate include in cxgb4.h
From: David Miller @ 2013-10-21 22:47 UTC (permalink / raw)
To: michael.opdenacker; +Cc: dm, netdev, linux-kernel
In-Reply-To: <1382245801-19192-1-git-send-email-michael.opdenacker@free-electrons.com>
From: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Date: Sun, 20 Oct 2013 07:10:01 +0200
> Reported by "make includecheck"
>
> Tested that C sources including this file still compile well on x86
>
> Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Applied.
^ permalink raw reply
* Re: [PATCH] Revert "bridge: only expire the mdb entry when query is received"
From: David Miller @ 2013-10-21 22:45 UTC (permalink / raw)
To: linus.luessing; +Cc: stephen, netdev, bridge, linux-kernel, amwang
In-Reply-To: <1382223537-10844-1-git-send-email-linus.luessing@web.de>
From: Linus Lüssing <linus.luessing@web.de>
Date: Sun, 20 Oct 2013 00:58:57 +0200
> While this commit was a good attempt to fix issues occuring when no
> multicast querier is present, this commit still has two more issues:
>
> 1) There are cases where mdb entries do not expire even if there is a
> querier present. The bridge will unnecessarily continue flooding
> multicast packets on the according ports.
>
> 2) Never removing an mdb entry could be exploited for a Denial of
> Service by an attacker on the local link, slowly, but steadily eating up
> all memory.
>
> Actually, this commit became obsolete with
> "bridge: disable snooping if there is no querier" (b00589af3b)
> which included fixes for a few more cases.
>
> Therefore reverting the following commits (the commit stated in the
> commit message plus three of its follow up fixes):
>
> ---
> Revert "bridge: update mdb expiration timer upon reports."
> This reverts commit f144febd93d5ee534fdf23505ab091b2b9088edc.
> Revert "bridge: do not call setup_timer() multiple times"
> This reverts commit 1faabf2aab1fdaa1ace4e8c829d1b9cf7bfec2f1.
> Revert "bridge: fix some kernel warning in multicast timer"
> This reverts commit c7e8e8a8f7a70b343ca1e0f90a31e35ab2d16de1.
> Revert "bridge: only expire the mdb entry when query is received"
> This reverts commit 9f00b2e7cf241fa389733d41b615efdaa2cb0f5b.
> ---
Cong, and other bridge folks, please review this revert.
Thanks.
^ permalink raw reply
* Re: [PATCH 0/6] ipv4: tcp_memcontrol and userns sysctls
From: David Miller @ 2013-10-21 22:44 UTC (permalink / raw)
To: ebiederm-aS9lmoZGLiVWk0Htik3J/w
Cc: netdev-u79uwXL29TY76Z2rM5mHXA,
containers-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA,
cgroups-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <87r4bghml4.fsf-aS9lmoZGLiVWk0Htik3J/w@public.gmane.org>
From: ebiederm-aS9lmoZGLiVWk0Htik3J/w@public.gmane.org (Eric W. Biederman)
Date: Sat, 19 Oct 2013 16:23:19 -0700
> While looking into allowing the ipv4 sysctls to be used in a network
> namespace I stumbled upon the mess that is tcp_memcontrol.
>
> I remove the dead code, broken code, and excessive abstraction in the
> tcp_memcontrols then I clean up up and allow in the user namespace the
> per net ipv4 sysctls.
I wish we hadn't installed this stuff in the first place, but better
to take care of it now than later.
Series applied, thanks Eric.
^ permalink raw reply
* Re: [PATCH net 2/3] ipv6: fill rt6i_gateway with nexthop address
From: David Miller @ 2013-10-21 22:42 UTC (permalink / raw)
To: ja; +Cc: hannes, netdev, netfilter-devel, lvs-devel, yoshfuji
In-Reply-To: <alpine.LFD.2.03.1310211009270.1522@ssi.bg>
From: Julian Anastasov <ja@ssi.bg>
Date: Mon, 21 Oct 2013 10:31:06 +0300 (EEST)
> Thanks for the review! I don't mind too about
> removing rt6_nexthop. For me it is 51% against 49% to keep it
> as it denotes the places that use nexthop and not gateway.
> May be more opinions will help to decide because I don't know
> if there are any plans to use similar techniques as done for IPv4.
I have no strong opinion about removing rt6_nexthop.
If it is of low cost today and makes the code easier to
undersand and grep, just leave it alone.
^ permalink raw reply
* Re: [PATCH net 0/3] ipv6: use rt6i_gateway as nexthop
From: David Miller @ 2013-10-21 22:40 UTC (permalink / raw)
To: ja; +Cc: netdev, netfilter-devel, lvs-devel, yoshfuji
In-Reply-To: <1382272985-1528-1-git-send-email-ja@ssi.bg>
From: Julian Anastasov <ja@ssi.bg>
Date: Sun, 20 Oct 2013 15:43:02 +0300
> I see the following two alternatives for applying these
> patches:
>
> 1. Linger patch 2 in net-next to avoid surprises in the upcoming
> release. In this case patch 3 can be reworked not to depend on
> the new rt6_nexthop() definition in patch 2. I guess this is a
> better option, so that patch 2 can be reviewed and tested for
> longer time.
>
> 2. Include all 3 patches in net tree - more risky because this
> is my first attempt to change IPv6.
I have decided to merge all three patches into -net right now.
I've reviewed these patches several times and they look good
to me.
I'll let them cook upstream for at least a week before submitting them
to -stable to let any last minute errors show themselves and
subsequently get resolved.
Thanks!
^ permalink raw reply
* Re: [PATCH net] netpoll: linearize skb before accessing its data
From: David Miller @ 2013-10-21 22:33 UTC (permalink / raw)
To: eric.dumazet; +Cc: antonio, netdev
In-Reply-To: <1382394336.3284.92.camel@edumazet-glaptop.roam.corp.google.com>
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Mon, 21 Oct 2013 15:25:36 -0700
> Anyway, how I see nothing sets rx_hook, what am I missing ?
Only out of tree code makes use of this facility, and it's been
this way since the facility was introduced.
Yes, I'm disappointed and unhappy about this too.
^ permalink raw reply
* Re: [PATCH net v2 0/9] bnx2x: Bug fixes patch series
From: David Miller @ 2013-10-21 22:32 UTC (permalink / raw)
To: yuvalmin; +Cc: netdev, ariele, eilong
In-Reply-To: <1382280694-8428-1-git-send-email-yuvalmin@broadcom.com>
From: "Yuval Mintz" <yuvalmin@broadcom.com>
Date: Sun, 20 Oct 2013 16:51:25 +0200
> This patch series contains fixes for various flows - several SR-IOV issues
> are fixed, ethtool callbacks (coalescing and register dump) are corrected,
> null pointer dereference on error flows is prevented, etc.
>
> Changes from V1
> ---------------
> - Patch 2 "bnx2x: Prevent an illegal pointer dereference during panic"
> is revised, with improved handling of edge cases.
Series applied, thanks for strengthening the address validation in
patch #2.
^ permalink raw reply
* Re: [PATCH net] netpoll: linearize skb before accessing its data
From: Eric Dumazet @ 2013-10-21 22:25 UTC (permalink / raw)
To: Antonio Quartulli; +Cc: David S. Miller, netdev
In-Reply-To: <1382391080-1607-1-git-send-email-antonio@meshcoding.com>
On Mon, 2013-10-21 at 23:31 +0200, Antonio Quartulli wrote:
> __netpoll_rx() assumes that the data buffer of the received
> skb is linear and then passes it to rx_hook().
> However this is not true because the skb has not been
> linearized yet.
>
> This can cause rx_hook() to access non allocated memory
> while parsing the received data.
>
> Fix __netpoll_rx() by explicitly linearising the skb.
>
> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
> ---
>
> I checked linux-3.0 and this bug seems to be already there. Please consider
> queueing it for stable.
>
>
> Regards,
>
>
>
> net/core/netpoll.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/net/core/netpoll.c b/net/core/netpoll.c
> index fc75c9e..97cff18 100644
> --- a/net/core/netpoll.c
> +++ b/net/core/netpoll.c
> @@ -814,6 +814,9 @@ int __netpoll_rx(struct sk_buff *skb, struct netpoll_info *npinfo)
> if (pskb_trim_rcsum(skb, len))
> goto out;
>
> + if (skb_linearize(skb))
> + goto out;
> +
> iph = (struct iphdr *)skb->data;
> if (iph->protocol != IPPROTO_UDP)
> goto out;
> @@ -855,6 +858,8 @@ int __netpoll_rx(struct sk_buff *skb, struct netpoll_info *npinfo)
> goto out;
> if (pskb_trim_rcsum(skb, len + sizeof(struct ipv6hdr)))
> goto out;
> + if (skb_linearize(skb))
> + goto out;
> ip6h = ipv6_hdr(skb);
> if (!pskb_may_pull(skb, sizeof(struct udphdr)))
> goto out;
Well, if you linearize the skb, no need for pskb_may_pull(),
and it would be better to do it once at the beginning...
Anyway, how I see nothing sets rx_hook, what am I missing ?
# git grep -n rx_hook
include/linux/netpoll.h:27: void (*rx_hook)(struct netpoll *, int, char *, int);
include/linux/netpoll.h:44: struct list_head rx_np; /* netpolls that registered an rx_hook */
net/core/netpoll.c:639: /* If there are several rx_hooks for the same address,
net/core/netpoll.c:722: /* If there are several rx_hooks for the same address,
net/core/netpoll.c:837: np->rx_hook(np, ntohs(uh->source),
net/core/netpoll.c:875: np->rx_hook(np, ntohs(uh->source),
net/core/netpoll.c:1065: if (np->rx_hook) {
^ permalink raw reply
* Re: [PATCH stable] inet: fix possible memory corruption with UDP_CORK and UFO
From: David Miller @ 2013-10-21 22:25 UTC (permalink / raw)
To: hannes; +Cc: netdev, jiri, eric.dumazet
In-Reply-To: <20131021220747.GC24158@order.stressinduktion.org>
From: Hannes Frederic Sowa <hannes@stressinduktion.org>
Date: Tue, 22 Oct 2013 00:07:47 +0200
> This is a replacement patch only for stable which does fix the problems
> handled by the following two commits in -net:
>
> "ip_output: do skb ufo init for peeked non ufo skb as well" (e93b7d748be887cd7639b113ba7d7ef792a7efb9)
> "ip6_output: do skb ufo init for peeked non ufo skb as well" (c547dbf55d5f8cf615ccc0e7265e98db27d3fb8b)
>
> Three frames are written on a corked udp socket for which the output
> netdevice has UFO enabled. If the first and third frame are smaller than
> the mtu and the second one is bigger, we enqueue the second frame with
> skb_append_datato_frags without initializing the gso fields. This leads
> to the third frame appended regulary and thus constructing an invalid skb.
>
> This fixes the problem by always using skb_append_datato_frags as soon
> as the first frag got enqueued to the skb without marking the packet
> as SKB_GSO_UDP.
>
> The problem with only two frames for ipv6 was fixed by "ipv6: udp
> packets following an UFO enqueued packet need also be handled by UFO"
> (2811ebac2521ceac84f2bdae402455baa6a7fb47).
>
> Cc: Jiri Pirko <jiri@resnulli.us>
> Cc: Eric Dumazet <eric.dumazet@gmail.com>
> Cc: David Miller <davem@davemloft.net>
> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Queued up for -stable, thanks Hannes.
^ permalink raw reply
* Re: [PATCH net] netpoll: linearize skb before accessing its data
From: David Miller @ 2013-10-21 22:23 UTC (permalink / raw)
To: antonio; +Cc: netdev
In-Reply-To: <1382391080-1607-1-git-send-email-antonio@meshcoding.com>
From: Antonio Quartulli <antonio@meshcoding.com>
Date: Mon, 21 Oct 2013 23:31:20 +0200
> __netpoll_rx() assumes that the data buffer of the received
> skb is linear and then passes it to rx_hook().
> However this is not true because the skb has not been
> linearized yet.
>
> This can cause rx_hook() to access non allocated memory
> while parsing the received data.
>
> Fix __netpoll_rx() by explicitly linearising the skb.
>
> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
It is rx_hook's obligation to access the SKB properly and not
assume that the SKB is linear. It is very expensive to
linearize every SKB just for the sake of improperly implemented
receive hooks.
In particular the rx hooks must make use of interface such
as pskb_may_pull(), just like every other protocol does
on packet input processing, to make sure the area they want
to access is in the linear area.
^ permalink raw reply
* Re: [net-next PATCH] macvlan: resolve ENOENT errors on creation
From: Veaceslav Falico @ 2013-10-21 22:05 UTC (permalink / raw)
To: John Fastabend; +Cc: nhorman, netdev
In-Reply-To: <5265A147.4010501@gmail.com>
On Mon, Oct 21, 2013 at 02:48:55PM -0700, John Fastabend wrote:
>On 10/21/2013 02:34 PM, Veaceslav Falico wrote:
>>On Mon, Oct 21, 2013 at 02:28:02PM -0700, John Fastabend wrote:
>>>After the commit below attempting to create macvlan devices was
>>>resulting in ENOENT errors,
>>>
>>># ip link add link p3p2 type macvlan
>>>RTNETLINK answers: Invalid argument
>>>
>>>This happens because netdev_upper_dev_link() is called before
>>>register_netdevice() in the macvlan code. Through a call chain
>>>this results in a call to __netdev_adjacent_dev_insert() and
>>>finally a sysfs_create_link(). This requires the kobject of
>>>the macvlan to be registered which is done in register_netdevice().
>>>If there is no kobject which is the case here the ENOENT error
>>>is seen on the command line.
>>>
>>>To resolve this move the netdev_upper_dev_link() call below
>>>the register_netdevice() call. This aligns with vlan driver
>>>flow.
>>
>>Yep, changed the vlan code, but didn't see the macvlan. My cscope didn't
>>catch it for some reason :-/.
>>
>>I've also checked - there are no users except bonding, vlan (both are ok),
>>and macvlan.
>>
>
>The openvswitch code uses netdev_master_upper_dev_link() which
>eventually calls __netdev_adjacent_dev_insert() as well. But from
>a quick code inspection I think it should work. Anyways that is one
>other user.
Yep, checked them also now:
team - links two already existing devices (team->dev and port_dev)
batadv - links existing device to another existing device, or creates of if
the latter doesn't exist (and calls register_netdev on creation)
bridge - links two already existing devices (bridge->dev and dev)
openvswitch - links two already existing devices (get_dpdev(vport->dp) and
the device found by dev_get_by_name()).
bonding - uses netdev_master_upper_dev_link_private(), and is also ok.
Hopefully we're safe.
>
>.John
>
>--
>John Fastabend Intel Corporation
^ permalink raw reply
* [PATCH stable] inet: fix possible memory corruption with UDP_CORK and UFO
From: Hannes Frederic Sowa @ 2013-10-21 22:07 UTC (permalink / raw)
To: netdev; +Cc: jiri, eric.dumazet, davem
This is a replacement patch only for stable which does fix the problems
handled by the following two commits in -net:
"ip_output: do skb ufo init for peeked non ufo skb as well" (e93b7d748be887cd7639b113ba7d7ef792a7efb9)
"ip6_output: do skb ufo init for peeked non ufo skb as well" (c547dbf55d5f8cf615ccc0e7265e98db27d3fb8b)
Three frames are written on a corked udp socket for which the output
netdevice has UFO enabled. If the first and third frame are smaller than
the mtu and the second one is bigger, we enqueue the second frame with
skb_append_datato_frags without initializing the gso fields. This leads
to the third frame appended regulary and thus constructing an invalid skb.
This fixes the problem by always using skb_append_datato_frags as soon
as the first frag got enqueued to the skb without marking the packet
as SKB_GSO_UDP.
The problem with only two frames for ipv6 was fixed by "ipv6: udp
packets following an UFO enqueued packet need also be handled by UFO"
(2811ebac2521ceac84f2bdae402455baa6a7fb47).
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
---
include/linux/skbuff.h | 5 +++++
net/ipv4/ip_output.c | 2 +-
net/ipv6/ip6_output.c | 2 +-
3 files changed, 7 insertions(+), 2 deletions(-)
diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h
index c2d8933..eee3d92 100644
--- a/include/linux/skbuff.h
+++ b/include/linux/skbuff.h
@@ -1316,6 +1316,11 @@ static inline int skb_pagelen(const struct sk_buff *skb)
return len + skb_headlen(skb);
}
+static inline bool skb_has_frags(const struct sk_buff *skb)
+{
+ return skb_shinfo(skb)->nr_frags;
+}
+
/**
* __skb_fill_page_desc - initialise a paged fragment in an skb
* @skb: buffer containing fragment to be initialised
diff --git a/net/ipv4/ip_output.c b/net/ipv4/ip_output.c
index 3982eab..13e617f 100644
--- a/net/ipv4/ip_output.c
+++ b/net/ipv4/ip_output.c
@@ -841,7 +841,7 @@ static int __ip_append_data(struct sock *sk,
csummode = CHECKSUM_PARTIAL;
cork->length += length;
- if (((length > mtu) || (skb && skb_is_gso(skb))) &&
+ if (((length > mtu) || (skb && skb_has_frags(skb))) &&
(sk->sk_protocol == IPPROTO_UDP) &&
(rt->dst.dev->features & NETIF_F_UFO) && !rt->dst.header_len) {
err = ip_ufo_append_data(sk, queue, getfrag, from, length,
diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c
index 975624b..65f28be 100644
--- a/net/ipv6/ip6_output.c
+++ b/net/ipv6/ip6_output.c
@@ -1230,7 +1230,7 @@ int ip6_append_data(struct sock *sk, int getfrag(void *from, char *to,
skb = skb_peek_tail(&sk->sk_write_queue);
cork->length += length;
if (((length > mtu) ||
- (skb && skb_is_gso(skb))) &&
+ (skb && skb_has_frags(skb))) &&
(sk->sk_protocol == IPPROTO_UDP) &&
(rt->dst.dev->features & NETIF_F_UFO)) {
err = ip6_ufo_append_data(sk, getfrag, from, length,
--
1.8.3.1
^ permalink raw reply related
* [PATCH] net-bnx2x: Fix byte order problem on NVRAM writes
From: Nate Klein @ 2013-10-21 21:57 UTC (permalink / raw)
To: netdev; +Cc: eilong, nxk, linux-kernel
Tested:
ethtool -e eth0 raw on >first.nvram
ethtool -E eth0 <first.nvram
ethtool -e eth0 raw on >second.nvram
cmp first.nvram second.nvram || ethtool -E eth0 <second.nvram
(No output means pass.)
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index 8213cc8..35671fb 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -1549,7 +1549,7 @@ static int bnx2x_nvram_write_dword(struct bnx2x *bp, u32 offset, u32 val,
REG_WR(bp, MCP_REG_MCPR_NVM_COMMAND, MCPR_NVM_COMMAND_DONE);
/* write the data */
- REG_WR(bp, MCP_REG_MCPR_NVM_WRITE, val);
+ REG_WR(bp, MCP_REG_MCPR_NVM_WRITE, cpu_to_be32(val));
/* address of the NVRAM to write to */
REG_WR(bp, MCP_REG_MCPR_NVM_ADDR,
--
1.8.4
^ permalink raw reply related
* Re: [net-next PATCH] macvlan: resolve ENOENT errors on creation
From: Neil Horman @ 2013-10-21 21:54 UTC (permalink / raw)
To: John Fastabend; +Cc: vfalico, netdev
In-Reply-To: <20131021212801.19330.69659.stgit@nitbit.x32>
On Mon, Oct 21, 2013 at 02:28:02PM -0700, John Fastabend wrote:
> After the commit below attempting to create macvlan devices was
> resulting in ENOENT errors,
>
> # ip link add link p3p2 type macvlan
> RTNETLINK answers: Invalid argument
>
> This happens because netdev_upper_dev_link() is called before
> register_netdevice() in the macvlan code. Through a call chain
> this results in a call to __netdev_adjacent_dev_insert() and
> finally a sysfs_create_link(). This requires the kobject of
> the macvlan to be registered which is done in register_netdevice().
> If there is no kobject which is the case here the ENOENT error
> is seen on the command line.
>
> To resolve this move the netdev_upper_dev_link() call below
> the register_netdevice() call. This aligns with vlan driver
> flow.
>
> Regression introduced here,
>
> commit 5831d66e8097aedfa3bc35941cf265ada2352317
> Author: Veaceslav Falico <vfalico@redhat.com>
> Date: Wed Sep 25 09:20:32 2013 +0200
>
> net: create sysfs symlinks for neighbour devices
>
> CC: Veaceslav Falico <vfalico@redhat.com>
> CC: Neil Horman <nhorman@tuxdriver.com>
> Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
^ permalink raw reply
* Re: [net-next PATCH] macvlan: resolve ENOENT errors on creation
From: John Fastabend @ 2013-10-21 21:48 UTC (permalink / raw)
To: Veaceslav Falico; +Cc: nhorman, netdev
In-Reply-To: <20131021213441.GB18170@redhat.com>
On 10/21/2013 02:34 PM, Veaceslav Falico wrote:
> On Mon, Oct 21, 2013 at 02:28:02PM -0700, John Fastabend wrote:
>> After the commit below attempting to create macvlan devices was
>> resulting in ENOENT errors,
>>
>> # ip link add link p3p2 type macvlan
>> RTNETLINK answers: Invalid argument
>>
>> This happens because netdev_upper_dev_link() is called before
>> register_netdevice() in the macvlan code. Through a call chain
>> this results in a call to __netdev_adjacent_dev_insert() and
>> finally a sysfs_create_link(). This requires the kobject of
>> the macvlan to be registered which is done in register_netdevice().
>> If there is no kobject which is the case here the ENOENT error
>> is seen on the command line.
>>
>> To resolve this move the netdev_upper_dev_link() call below
>> the register_netdevice() call. This aligns with vlan driver
>> flow.
>
> Yep, changed the vlan code, but didn't see the macvlan. My cscope didn't
> catch it for some reason :-/.
>
> I've also checked - there are no users except bonding, vlan (both are ok),
> and macvlan.
>
The openvswitch code uses netdev_master_upper_dev_link() which
eventually calls __netdev_adjacent_dev_insert() as well. But from
a quick code inspection I think it should work. Anyways that is one
other user.
.John
--
John Fastabend Intel Corporation
^ permalink raw reply
* Re: [net-next PATCH] macvlan: resolve ENOENT errors on creation
From: Veaceslav Falico @ 2013-10-21 21:34 UTC (permalink / raw)
To: John Fastabend; +Cc: nhorman, netdev
In-Reply-To: <20131021212801.19330.69659.stgit@nitbit.x32>
On Mon, Oct 21, 2013 at 02:28:02PM -0700, John Fastabend wrote:
>After the commit below attempting to create macvlan devices was
>resulting in ENOENT errors,
>
># ip link add link p3p2 type macvlan
>RTNETLINK answers: Invalid argument
>
>This happens because netdev_upper_dev_link() is called before
>register_netdevice() in the macvlan code. Through a call chain
>this results in a call to __netdev_adjacent_dev_insert() and
>finally a sysfs_create_link(). This requires the kobject of
>the macvlan to be registered which is done in register_netdevice().
>If there is no kobject which is the case here the ENOENT error
>is seen on the command line.
>
>To resolve this move the netdev_upper_dev_link() call below
>the register_netdevice() call. This aligns with vlan driver
>flow.
Yep, changed the vlan code, but didn't see the macvlan. My cscope didn't
catch it for some reason :-/.
I've also checked - there are no users except bonding, vlan (both are ok),
and macvlan.
Acked-by: Veaceslav Falico <vfalico@redhat.com>
>
>Regression introduced here,
>
>commit 5831d66e8097aedfa3bc35941cf265ada2352317
>Author: Veaceslav Falico <vfalico@redhat.com>
>Date: Wed Sep 25 09:20:32 2013 +0200
>
> net: create sysfs symlinks for neighbour devices
>
>CC: Veaceslav Falico <vfalico@redhat.com>
>CC: Neil Horman <nhorman@tuxdriver.com>
>Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
>---
> drivers/net/macvlan.c | 11 +++++------
> 1 file changed, 5 insertions(+), 6 deletions(-)
>
>diff --git a/drivers/net/macvlan.c b/drivers/net/macvlan.c
>index 9bf46bd..cc9845e 100644
>--- a/drivers/net/macvlan.c
>+++ b/drivers/net/macvlan.c
>@@ -828,22 +828,21 @@ int macvlan_common_newlink(struct net *src_net, struct net_device *dev,
> eth_hw_addr_inherit(dev, lowerdev);
> }
>
>+ port->count += 1;
>+ err = register_netdevice(dev);
>+ if (err < 0)
>+ goto destroy_port;
>+
> err = netdev_upper_dev_link(lowerdev, dev);
> if (err)
> goto destroy_port;
>
>- port->count += 1;
>- err = register_netdevice(dev);
>- if (err < 0)
>- goto upper_dev_unlink;
>
> list_add_tail_rcu(&vlan->list, &port->vlans);
> netif_stacked_transfer_operstate(lowerdev, dev);
>
> return 0;
>
>-upper_dev_unlink:
>- netdev_upper_dev_unlink(lowerdev, dev);
> destroy_port:
> port->count -= 1;
> if (!port->count)
>
^ permalink raw reply
* [PATCH net] netpoll: linearize skb before accessing its data
From: Antonio Quartulli @ 2013-10-21 21:31 UTC (permalink / raw)
To: David S. Miller; +Cc: netdev, Antonio Quartulli
__netpoll_rx() assumes that the data buffer of the received
skb is linear and then passes it to rx_hook().
However this is not true because the skb has not been
linearized yet.
This can cause rx_hook() to access non allocated memory
while parsing the received data.
Fix __netpoll_rx() by explicitly linearising the skb.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
---
I checked linux-3.0 and this bug seems to be already there. Please consider
queueing it for stable.
Regards,
net/core/netpoll.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/net/core/netpoll.c b/net/core/netpoll.c
index fc75c9e..97cff18 100644
--- a/net/core/netpoll.c
+++ b/net/core/netpoll.c
@@ -814,6 +814,9 @@ int __netpoll_rx(struct sk_buff *skb, struct netpoll_info *npinfo)
if (pskb_trim_rcsum(skb, len))
goto out;
+ if (skb_linearize(skb))
+ goto out;
+
iph = (struct iphdr *)skb->data;
if (iph->protocol != IPPROTO_UDP)
goto out;
@@ -855,6 +858,8 @@ int __netpoll_rx(struct sk_buff *skb, struct netpoll_info *npinfo)
goto out;
if (pskb_trim_rcsum(skb, len + sizeof(struct ipv6hdr)))
goto out;
+ if (skb_linearize(skb))
+ goto out;
ip6h = ipv6_hdr(skb);
if (!pskb_may_pull(skb, sizeof(struct udphdr)))
goto out;
--
1.8.4
^ permalink raw reply related
* [net-next PATCH] macvlan: resolve ENOENT errors on creation
From: John Fastabend @ 2013-10-21 21:28 UTC (permalink / raw)
To: vfalico, nhorman; +Cc: netdev
After the commit below attempting to create macvlan devices was
resulting in ENOENT errors,
# ip link add link p3p2 type macvlan
RTNETLINK answers: Invalid argument
This happens because netdev_upper_dev_link() is called before
register_netdevice() in the macvlan code. Through a call chain
this results in a call to __netdev_adjacent_dev_insert() and
finally a sysfs_create_link(). This requires the kobject of
the macvlan to be registered which is done in register_netdevice().
If there is no kobject which is the case here the ENOENT error
is seen on the command line.
To resolve this move the netdev_upper_dev_link() call below
the register_netdevice() call. This aligns with vlan driver
flow.
Regression introduced here,
commit 5831d66e8097aedfa3bc35941cf265ada2352317
Author: Veaceslav Falico <vfalico@redhat.com>
Date: Wed Sep 25 09:20:32 2013 +0200
net: create sysfs symlinks for neighbour devices
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
---
drivers/net/macvlan.c | 11 +++++------
1 file changed, 5 insertions(+), 6 deletions(-)
diff --git a/drivers/net/macvlan.c b/drivers/net/macvlan.c
index 9bf46bd..cc9845e 100644
--- a/drivers/net/macvlan.c
+++ b/drivers/net/macvlan.c
@@ -828,22 +828,21 @@ int macvlan_common_newlink(struct net *src_net, struct net_device *dev,
eth_hw_addr_inherit(dev, lowerdev);
}
+ port->count += 1;
+ err = register_netdevice(dev);
+ if (err < 0)
+ goto destroy_port;
+
err = netdev_upper_dev_link(lowerdev, dev);
if (err)
goto destroy_port;
- port->count += 1;
- err = register_netdevice(dev);
- if (err < 0)
- goto upper_dev_unlink;
list_add_tail_rcu(&vlan->list, &port->vlans);
netif_stacked_transfer_operstate(lowerdev, dev);
return 0;
-upper_dev_unlink:
- netdev_upper_dev_unlink(lowerdev, dev);
destroy_port:
port->count -= 1;
if (!port->count)
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox