* Re: Misalignment, MIPS, and ip_hdr(skb)->version
From: Hannes Frederic Sowa @ 2016-12-08 0:30 UTC (permalink / raw)
To: Jason A. Donenfeld, Netdev, linux-mips; +Cc: LKML, WireGuard mailing list
In-Reply-To: <CAHmME9o_eCNXpVztOZKW55kpRtE+1KSEQTQOjUBVn68Y2+or2g@mail.gmail.com>
Hi Jason,
On 07.12.2016 19:35, Jason A. Donenfeld wrote:
> I receive encrypted packets with a 13 byte header. I decrypt the
> ciphertext in place, and then discard the header. I then pass the
> plaintext to the rest of the networking stack. The plaintext is an IP
> packet. Due to the 13 byte header that was discarded, the plaintext
> possibly begins at an unaligned location (depending on whether
> dev->needed_headroom was respected).
>
> Does this matter? Is this bad? Will there be a necessary performance hit?
Your custom protocol should be designed in a way you get an aligned ip
header. Most protocols of the IETF follow this mantra and it is always
possible to e.g. pad options so you end up on aligned boundaries for the
next header.
GRE-TEB for example needs skb_copy_bits to extract the header so it can
access them in an aligned way.
> In order to find out, I instrumented the MIPS unaligned access
> exception handler to see where I was actually in trouble.
> Surprisingly, the only part of the stack that seemed to be upset was
> on calls to ip_hdr(skb)->version.
>
> Two things disturb me about this. First, this seems too good to be
> true. Does it seem reasonable to you that this is actually the only
> place that would be problematic? Or was my testing methodology wrong
> to arrive at such an optimistic conclusion?
>
> Secondly, why should a call to ip_hdr(skb)->version cause an unaligned
> access anyway? This struct member is simply the second half of a
> single byte in a bit field. I'd expect for the compiler to generate a
> single byte load, followed by a bitshift or a mask. Instead, the
> compiler appears to generate a double byte load, hence the exception.
> What's up with this? Stupid compiler that should be fixed? Some odd
> optimization? What to do?
I don't see an issue with that at all. Why do you think it could be a
problem?
Bye,
Hannes
^ permalink raw reply
* Re: Misalignment, MIPS, and ip_hdr(skb)->version
From: Jason A. Donenfeld @ 2016-12-08 0:29 UTC (permalink / raw)
To: David Miller; +Cc: Netdev, WireGuard mailing list, LKML, linux-mips
In-Reply-To: <20161207.145240.1636297838792223189.davem@davemloft.net>
On Wed, Dec 7, 2016 at 8:52 PM, David Miller <davem@davemloft.net> wrote:
> The only truly difficult case to handle is GRE encapsulation. Is
> that the situation you are running into?
>
> If not, please figure out what the header configuration looks like
> in the case that hits for you, and what the originating device is
> just in case it is a device driver issue.
My case is my own driver and my own protocol, which uses a 13 byte
header. I can, if absolutely necessary, change the protocol to add
another byte of padding. Or I can choose not to decrypt in place but
rather use a different trick, like overwriting the header during
decryption, though this removes some of the scatterwalk optimizations
when src and dst are the same. Or something else. I wrote the top
email of this thread inquiring about just exactly how bad it is to
call netif_rx(skb) when skb->data is unaligned.
^ permalink raw reply
* Re: [PATCH 2/2] [v2] net: qcom/emac: add support for the Qualcomm Technologies QDF2400
From: kbuild test robot @ 2016-12-08 0:26 UTC (permalink / raw)
To: Timur Tabi; +Cc: kbuild-all, David Miller, netdev, alokc
In-Reply-To: <1481143186-20137-3-git-send-email-timur@codeaurora.org>
[-- Attachment #1: Type: text/plain, Size: 1658 bytes --]
Hi Timur,
[auto build test ERROR on net-next/master]
[also build test ERROR on v4.9-rc8 next-20161207]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Timur-Tabi/net-qcom-emac-simplify-support-for-different-SOCs/20161208-064231
config: xtensa-allmodconfig (attached as .config)
compiler: xtensa-linux-gcc (GCC) 4.9.0
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=xtensa
All errors (new ones prefixed by >>):
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c: In function 'emac_sgmii_acpi_match':
>> drivers/net/ethernet/qualcomm/emac/emac-sgmii.c:178:3: error: implicit declaration of function 'acpi_evaluate_integer' [-Werror=implicit-function-declaration]
status = acpi_evaluate_integer(handle, "_HRV", NULL, &hrv);
^
cc1: some warnings being treated as errors
vim +/acpi_evaluate_integer +178 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
172
173 if (id) {
174 acpi_handle handle = ACPI_HANDLE(dev);
175 unsigned long long hrv;
176 acpi_status status;
177
> 178 status = acpi_evaluate_integer(handle, "_HRV", NULL, &hrv);
179 if (status) {
180 if (status == AE_NOT_FOUND)
181 /* Older versions of the QDF2432 ACPI tables do
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 47257 bytes --]
^ permalink raw reply
* Re: [net-next v2 02/19] i40e: simplify txd use count calculation
From: Eric Dumazet @ 2016-12-08 0:16 UTC (permalink / raw)
To: Jeff Kirsher
Cc: davem, Mitch Williams, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Alexander Duyck
In-Reply-To: <20161207221918.57932-3-jeffrey.t.kirsher@intel.com>
On Wed, 2016-12-07 at 14:19 -0800, Jeff Kirsher wrote:
> From: Mitch Williams <mitch.a.williams@intel.com>
>
> The i40e_txd_use_count function was fast but confusing. In the comments,
> it even admits that it's ugly. So replace it with a new function that is
> (very) slightly faster and has extensive commenting to help the thicker
> among us (including the author, who will forget in a week) understand
> how it works.
>
> Change-ID: Ifb533f13786a0bf39cb29f77969a5be2c83d9a87
> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> drivers/net/ethernet/intel/i40e/i40e_txrx.h | 45 +++++++++++++++++----------
> drivers/net/ethernet/intel/i40evf/i40e_txrx.h | 45 +++++++++++++++++----------
> 2 files changed, 56 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
> index de8550f..e065321 100644
> --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h
> +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
> @@ -173,26 +173,37 @@ static inline bool i40e_test_staterr(union i40e_rx_desc *rx_desc,
> #define I40E_MAX_DATA_PER_TXD_ALIGNED \
> (I40E_MAX_DATA_PER_TXD & ~(I40E_MAX_READ_REQ_SIZE - 1))
>
> -/* This ugly bit of math is equivalent to DIV_ROUNDUP(size, X) where X is
> - * the value I40E_MAX_DATA_PER_TXD_ALIGNED. It is needed due to the fact
> - * that 12K is not a power of 2 and division is expensive. It is used to
> - * approximate the number of descriptors used per linear buffer. Note
> - * that this will overestimate in some cases as it doesn't account for the
> - * fact that we will add up to 4K - 1 in aligning the 12K buffer, however
> - * the error should not impact things much as large buffers usually mean
> - * we will use fewer descriptors then there are frags in an skb.
> +/**
> + * i40e_txd_use_count - estimate the number of descriptors needed for Tx
> + * @size: transmit request size in bytes
> + *
> + * Due to hardware alignment restrictions (4K alignment), we need to
> + * assume that we can have no more than 12K of data per descriptor, even
> + * though each descriptor can take up to 16K - 1 bytes of aligned memory.
> + * Thus, we need to divide by 12K. But division is slow! Instead,
> + * we decompose the operation into shifts and one relatively cheap
> + * multiply operation.
> + *
> + * To divide by 12K, we first divide by 4K, then divide by 3:
> + * To divide by 4K, shift right by 12 bits
> + * To divide by 3, multiply by 85, then divide by 256
> + * (Divide by 256 is done by shifting right by 8 bits)
> + * Finally, we add one to round up. Because 256 isn't an exact multiple of
> + * 3, we'll underestimate near each multiple of 12K. This is actually more
> + * accurate as we have 4K - 1 of wiggle room that we can fit into the last
> + * segment. For our purposes this is accurate out to 1M which is orders of
> + * magnitude greater than our largest possible GSO size.
> + *
> + * This would then be implemented as:
> + * return (((size >> 12) * 85) >> 8) + 1;
> + *
> + * Since multiplication and division are commutative, we can reorder
> + * operations into:
> + * return ((size * 85) >> 20) + 1;
> */
> static inline unsigned int i40e_txd_use_count(unsigned int size)
> {
> - const unsigned int max = I40E_MAX_DATA_PER_TXD_ALIGNED;
> - const unsigned int reciprocal = ((1ull << 32) - 1 + (max / 2)) / max;
> - unsigned int adjust = ~(u32)0;
> -
> - /* if we rounded up on the reciprocal pull down the adjustment */
> - if ((max * reciprocal) > adjust)
> - adjust = ~(u32)(reciprocal - 1);
> -
> - return (u32)((((u64)size * reciprocal) + adjust) >> 32);
> + return ((size * 85) >> 20) + 1;
> }
But...
I thought gcc already implemented reciprocal divides ?
$ cat div.c
unsigned int foo(unsigned int size)
{
return size / 0x3000;
}
$ gcc -O2 -S div.c && cat div.s
foo:
.LFB0:
.cfi_startproc
movl %edi, %eax
movl $-1431655765, %edx // 0xaaaaaaab
mull %edx
shrl $13, %edx
movl %edx, %eax
ret
^ permalink raw reply
* Re: [net-next v2 00/19][pull request] 40GbE Intel Wired LAN Driver Updates 2016-12-07
From: David Miller @ 2016-12-08 0:15 UTC (permalink / raw)
To: jeffrey.t.kirsher; +Cc: netdev, nhorman, sassmann, jogreene, guru.anbalagane
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Wed, 7 Dec 2016 14:18:59 -0800
> This series contains updates to i40e and i40evf only.
Pulled, thanks Jeff.
^ permalink raw reply
* [PATCH v4 net-next 0/4]: Allow head adjustment in XDP prog
From: Martin KaFai Lau @ 2016-12-07 23:53 UTC (permalink / raw)
To: netdev
Cc: Alexei Starovoitov, Brenden Blanco, Daniel Borkmann, David Miller,
Jakub Kicinski, Jesper Dangaard Brouer, John Fastabend,
Saeed Mahameed, Tariq Toukan, Kernel Team
This series adds a helper to allow head adjusting in XDP prog. mlx4
driver has been modified to support this feature. An example is written
to encapsulate a packet with an IPv4/v6 header and then XDP_TX it
out.
v4:
1. Remove XDP_QUERY_FEATURES command. Instead, check
the prog->xdp_adjust_head bit inside the driver itself
during XDP_SETUP_PROG in patch 1of4.
Thanks for everybody's ideas.
2. Nit changes on sample code per Jesper
v3:
1. Check if the driver supports head adjustment before
setting the xdp_prog fd to the device in patch 1of4.
2. Remove the page alignment assumption on the data_hard_start.
Instead, add data_hard_start to the struct xdp_buff and the
driver has to fill it if it supports head adjustment.
3. Keep the wire MTU as before in mlx4
4. Set map0_byte_count to PAGE_SIZE in patch 3of4
v2:
1. Make a variable name change in bpf_xdp_adjust_head() in patch 1
2. Ensure no less than ETH_HLEN data in bpf_xdp_adjust_head() in patch 1
3. Some clarifications in commit log messages of patch 2 and 3
Thanks,
Martin
Martin KaFai Lau (4):
bpf: xdp: Allow head adjustment in XDP prog
mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs
mlx4: xdp: Reserve headroom for receiving packet when XDP prog is
active
bpf: xdp: Add XDP example for head adjustment
arch/powerpc/net/bpf_jit_comp64.c | 4 +-
arch/s390/net/bpf_jit_comp.c | 2 +-
arch/x86/net/bpf_jit_comp.c | 2 +-
drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 29 ++-
drivers/net/ethernet/mellanox/mlx4/en_rx.c | 70 +++---
drivers/net/ethernet/mellanox/mlx4/en_tx.c | 9 +-
drivers/net/ethernet/mellanox/mlx4/mlx4_en.h | 3 +-
drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 5 +
.../net/ethernet/netronome/nfp/nfp_net_common.c | 4 +
drivers/net/ethernet/qlogic/qede/qede_main.c | 5 +
include/linux/filter.h | 6 +-
include/uapi/linux/bpf.h | 11 +-
kernel/bpf/core.c | 2 +-
kernel/bpf/syscall.c | 2 +
kernel/bpf/verifier.c | 2 +-
net/core/filter.c | 28 ++-
samples/bpf/Makefile | 4 +
samples/bpf/bpf_helpers.h | 2 +
samples/bpf/bpf_load.c | 94 ++++++++
samples/bpf/bpf_load.h | 1 +
samples/bpf/xdp1_user.c | 93 --------
samples/bpf/xdp_tx_iptunnel_common.h | 37 +++
samples/bpf/xdp_tx_iptunnel_kern.c | 236 +++++++++++++++++++
samples/bpf/xdp_tx_iptunnel_user.c | 256 +++++++++++++++++++++
24 files changed, 762 insertions(+), 145 deletions(-)
create mode 100644 samples/bpf/xdp_tx_iptunnel_common.h
create mode 100644 samples/bpf/xdp_tx_iptunnel_kern.c
create mode 100644 samples/bpf/xdp_tx_iptunnel_user.c
--
2.5.1
^ permalink raw reply
* [PATCH v4 net-next 3/4] mlx4: xdp: Reserve headroom for receiving packet when XDP prog is active
From: Martin KaFai Lau @ 2016-12-07 23:53 UTC (permalink / raw)
To: netdev
Cc: Alexei Starovoitov, Brenden Blanco, Daniel Borkmann, David Miller,
Jakub Kicinski, Jesper Dangaard Brouer, John Fastabend,
Saeed Mahameed, Tariq Toukan, Kernel Team
In-Reply-To: <1481154794-2311034-1-git-send-email-kafai@fb.com>
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
---
drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 8 ++------
drivers/net/ethernet/mellanox/mlx4/en_rx.c | 24 ++++++++++++++++++------
drivers/net/ethernet/mellanox/mlx4/en_tx.c | 9 +++++----
drivers/net/ethernet/mellanox/mlx4/mlx4_en.h | 3 ++-
4 files changed, 27 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index c97d25b06444..bcd955339058 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -51,7 +51,8 @@
#include "mlx4_en.h"
#include "en_port.h"
-#define MLX4_EN_MAX_XDP_MTU ((int)(PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN)))
+#define MLX4_EN_MAX_XDP_MTU ((int)(PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) - \
+ XDP_PACKET_HEADROOM))
int mlx4_en_setup_tc(struct net_device *dev, u8 up)
{
@@ -2700,11 +2701,6 @@ static int mlx4_xdp_set(struct net_device *dev, struct bpf_prog *prog)
int err;
int i;
- if (prog && prog->xdp_adjust_head) {
- en_err(priv, "Does not support bpf_xdp_adjust_head()\n");
- return -EOPNOTSUPP;
- }
-
xdp_ring_num = prog ? priv->rx_ring_num : 0;
/* No need to reconfigure buffers when simply swapping the
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_rx.c b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
index 23e9d04d1ef4..3c37e216bbf3 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_rx.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
@@ -96,7 +96,6 @@ static int mlx4_en_alloc_frags(struct mlx4_en_priv *priv,
struct mlx4_en_rx_alloc page_alloc[MLX4_EN_MAX_RX_FRAGS];
const struct mlx4_en_frag_info *frag_info;
struct page *page;
- dma_addr_t dma;
int i;
for (i = 0; i < priv->num_frags; i++) {
@@ -115,9 +114,10 @@ static int mlx4_en_alloc_frags(struct mlx4_en_priv *priv,
for (i = 0; i < priv->num_frags; i++) {
frags[i] = ring_alloc[i];
- dma = ring_alloc[i].dma + ring_alloc[i].page_offset;
+ frags[i].page_offset += priv->frag_info[i].rx_headroom;
+ rx_desc->data[i].addr = cpu_to_be64(frags[i].dma +
+ frags[i].page_offset);
ring_alloc[i] = page_alloc[i];
- rx_desc->data[i].addr = cpu_to_be64(dma);
}
return 0;
@@ -250,7 +250,8 @@ static int mlx4_en_prepare_rx_desc(struct mlx4_en_priv *priv,
if (ring->page_cache.index > 0) {
frags[0] = ring->page_cache.buf[--ring->page_cache.index];
- rx_desc->data[0].addr = cpu_to_be64(frags[0].dma);
+ rx_desc->data[0].addr = cpu_to_be64(frags[0].dma +
+ frags[0].page_offset);
return 0;
}
@@ -889,6 +890,7 @@ int mlx4_en_process_rx_cq(struct net_device *dev, struct mlx4_en_cq *cq, int bud
if (xdp_prog) {
struct xdp_buff xdp;
dma_addr_t dma;
+ void *orig_data;
u32 act;
dma = be64_to_cpu(rx_desc->data[0].addr);
@@ -896,11 +898,19 @@ int mlx4_en_process_rx_cq(struct net_device *dev, struct mlx4_en_cq *cq, int bud
priv->frag_info[0].frag_size,
DMA_FROM_DEVICE);
- xdp.data = page_address(frags[0].page) +
- frags[0].page_offset;
+ xdp.data_hard_start = page_address(frags[0].page);
+ xdp.data = xdp.data_hard_start + frags[0].page_offset;
xdp.data_end = xdp.data + length;
+ orig_data = xdp.data;
act = bpf_prog_run_xdp(xdp_prog, &xdp);
+
+ if (xdp.data != orig_data) {
+ length = xdp.data_end - xdp.data;
+ frags[0].page_offset = xdp.data -
+ xdp.data_hard_start;
+ }
+
switch (act) {
case XDP_PASS:
break;
@@ -1180,6 +1190,7 @@ void mlx4_en_calc_rx_buf(struct net_device *dev)
*/
priv->frag_info[0].frag_stride = PAGE_SIZE;
priv->frag_info[0].dma_dir = PCI_DMA_BIDIRECTIONAL;
+ priv->frag_info[0].rx_headroom = XDP_PACKET_HEADROOM;
i = 1;
} else {
int buf_size = 0;
@@ -1194,6 +1205,7 @@ void mlx4_en_calc_rx_buf(struct net_device *dev)
ALIGN(priv->frag_info[i].frag_size,
SMP_CACHE_BYTES);
priv->frag_info[i].dma_dir = PCI_DMA_FROMDEVICE;
+ priv->frag_info[i].rx_headroom = 0;
buf_size += priv->frag_info[i].frag_size;
i++;
}
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_tx.c b/drivers/net/ethernet/mellanox/mlx4/en_tx.c
index 4b597dca5c52..5886ad78058f 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_tx.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_tx.c
@@ -354,7 +354,7 @@ u32 mlx4_en_recycle_tx_desc(struct mlx4_en_priv *priv,
struct mlx4_en_rx_alloc frame = {
.page = tx_info->page,
.dma = tx_info->map0_dma,
- .page_offset = 0,
+ .page_offset = XDP_PACKET_HEADROOM,
.page_size = PAGE_SIZE,
};
@@ -1132,7 +1132,7 @@ netdev_tx_t mlx4_en_xmit_frame(struct mlx4_en_rx_ring *rx_ring,
tx_info->page = frame->page;
frame->page = NULL;
tx_info->map0_dma = dma;
- tx_info->map0_byte_count = length;
+ tx_info->map0_byte_count = PAGE_SIZE;
tx_info->nr_txbb = nr_txbb;
tx_info->nr_bytes = max_t(unsigned int, length, ETH_ZLEN);
tx_info->data_offset = (void *)data - (void *)tx_desc;
@@ -1141,9 +1141,10 @@ netdev_tx_t mlx4_en_xmit_frame(struct mlx4_en_rx_ring *rx_ring,
tx_info->linear = 1;
tx_info->inl = 0;
- dma_sync_single_for_device(priv->ddev, dma, length, PCI_DMA_TODEVICE);
+ dma_sync_single_range_for_device(priv->ddev, dma, frame->page_offset,
+ length, PCI_DMA_TODEVICE);
- data->addr = cpu_to_be64(dma);
+ data->addr = cpu_to_be64(dma + frame->page_offset);
data->lkey = ring->mr_key;
dma_wmb();
data->byte_count = cpu_to_be32(length);
diff --git a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
index 20a936428f4a..ba1c6cd0cc79 100644
--- a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
+++ b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
@@ -475,7 +475,8 @@ struct mlx4_en_frag_info {
u16 frag_prefix_size;
u32 frag_stride;
enum dma_data_direction dma_dir;
- int order;
+ u16 order;
+ u16 rx_headroom;
};
#ifdef CONFIG_MLX4_EN_DCB
--
2.5.1
^ permalink raw reply related
* [PATCH v4 net-next 1/4] bpf: xdp: Allow head adjustment in XDP prog
From: Martin KaFai Lau @ 2016-12-07 23:53 UTC (permalink / raw)
To: netdev
Cc: Alexei Starovoitov, Brenden Blanco, Daniel Borkmann, David Miller,
Jakub Kicinski, Jesper Dangaard Brouer, John Fastabend,
Saeed Mahameed, Tariq Toukan, Kernel Team
In-Reply-To: <1481154794-2311034-1-git-send-email-kafai@fb.com>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
---
arch/powerpc/net/bpf_jit_comp64.c | 4 ++--
arch/s390/net/bpf_jit_comp.c | 2 +-
arch/x86/net/bpf_jit_comp.c | 2 +-
drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 5 ++++
drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 5 ++++
.../net/ethernet/netronome/nfp/nfp_net_common.c | 4 ++++
drivers/net/ethernet/qlogic/qede/qede_main.c | 5 ++++
include/linux/filter.h | 6 +++--
include/uapi/linux/bpf.h | 11 ++++++++-
kernel/bpf/core.c | 2 +-
kernel/bpf/syscall.c | 2 ++
kernel/bpf/verifier.c | 2 +-
net/core/filter.c | 28 ++++++++++++++++++++--
13 files changed, 67 insertions(+), 11 deletions(-)
diff --git a/arch/powerpc/net/bpf_jit_comp64.c b/arch/powerpc/net/bpf_jit_comp64.c
index 0fe98a567125..73a5cf18fd84 100644
--- a/arch/powerpc/net/bpf_jit_comp64.c
+++ b/arch/powerpc/net/bpf_jit_comp64.c
@@ -766,7 +766,7 @@ static int bpf_jit_build_body(struct bpf_prog *fp, u32 *image,
func = (u8 *) __bpf_call_base + imm;
/* Save skb pointer if we need to re-cache skb data */
- if (bpf_helper_changes_skb_data(func))
+ if (bpf_helper_changes_pkt_data(func))
PPC_BPF_STL(3, 1, bpf_jit_stack_local(ctx));
bpf_jit_emit_func_call(image, ctx, (u64)func);
@@ -775,7 +775,7 @@ static int bpf_jit_build_body(struct bpf_prog *fp, u32 *image,
PPC_MR(b2p[BPF_REG_0], 3);
/* refresh skb cache */
- if (bpf_helper_changes_skb_data(func)) {
+ if (bpf_helper_changes_pkt_data(func)) {
/* reload skb pointer to r3 */
PPC_BPF_LL(3, 1, bpf_jit_stack_local(ctx));
bpf_jit_emit_skb_loads(image, ctx);
diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c
index bee281f3163d..167b31b186c1 100644
--- a/arch/s390/net/bpf_jit_comp.c
+++ b/arch/s390/net/bpf_jit_comp.c
@@ -981,7 +981,7 @@ static noinline int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i
EMIT2(0x0d00, REG_14, REG_W1);
/* lgr %b0,%r2: load return value into %b0 */
EMIT4(0xb9040000, BPF_REG_0, REG_2);
- if (bpf_helper_changes_skb_data((void *)func)) {
+ if (bpf_helper_changes_pkt_data((void *)func)) {
jit->seen |= SEEN_SKB_CHANGE;
/* lg %b1,ST_OFF_SKBP(%r15) */
EMIT6_DISP_LH(0xe3000000, 0x0004, BPF_REG_1, REG_0,
diff --git a/arch/x86/net/bpf_jit_comp.c b/arch/x86/net/bpf_jit_comp.c
index fe04a04dab8e..e76d1af60f7a 100644
--- a/arch/x86/net/bpf_jit_comp.c
+++ b/arch/x86/net/bpf_jit_comp.c
@@ -853,7 +853,7 @@ xadd: if (is_imm8(insn->off))
func = (u8 *) __bpf_call_base + imm32;
jmp_offset = func - (image + addrs[i]);
if (seen_ld_abs) {
- reload_skb_data = bpf_helper_changes_skb_data(func);
+ reload_skb_data = bpf_helper_changes_pkt_data(func);
if (reload_skb_data) {
EMIT1(0x57); /* push %rdi */
jmp_offset += 22; /* pop, mov, sub, mov */
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index 49a81f1fc1d6..f441eda63bec 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -2686,6 +2686,11 @@ static int mlx4_xdp_set(struct net_device *dev, struct bpf_prog *prog)
int err;
int i;
+ if (prog && prog->xdp_adjust_head) {
+ en_err(priv, "Does not support bpf_xdp_adjust_head()\n");
+ return -EOPNOTSUPP;
+ }
+
xdp_ring_num = prog ? priv->rx_ring_num : 0;
/* No need to reconfigure buffers when simply swapping the
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
index 9def5cc378a3..504ca130f88d 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -3180,6 +3180,11 @@ static int mlx5e_xdp_set(struct net_device *netdev, struct bpf_prog *prog)
bool reset, was_opened;
int i;
+ if (prog && prog->xdp_adjust_head) {
+ netdev_err(netdev, "Does not support bpf_xdp_adjust_head()\n");
+ return -EOPNOTSUPP;
+ }
+
mutex_lock(&priv->state_lock);
if ((netdev->features & NETIF_F_LRO) && prog) {
diff --git a/drivers/net/ethernet/netronome/nfp/nfp_net_common.c b/drivers/net/ethernet/netronome/nfp/nfp_net_common.c
index 00d9a03be31d..e8d448109e03 100644
--- a/drivers/net/ethernet/netronome/nfp/nfp_net_common.c
+++ b/drivers/net/ethernet/netronome/nfp/nfp_net_common.c
@@ -2946,6 +2946,10 @@ static int nfp_net_xdp_setup(struct nfp_net *nn, struct bpf_prog *prog)
};
int err;
+ if (prog && prog->xdp_adjust_head) {
+ nn_err(nn, "Does not support bpf_xdp_adjust_head()\n");
+ return -EOPNOTSUPP;
+ }
if (!prog && !nn->xdp_prog)
return 0;
if (prog && nn->xdp_prog) {
diff --git a/drivers/net/ethernet/qlogic/qede/qede_main.c b/drivers/net/ethernet/qlogic/qede/qede_main.c
index cf1dd1436d93..aecdd1c5c0ea 100644
--- a/drivers/net/ethernet/qlogic/qede/qede_main.c
+++ b/drivers/net/ethernet/qlogic/qede/qede_main.c
@@ -2507,6 +2507,11 @@ static int qede_xdp_set(struct qede_dev *edev, struct bpf_prog *prog)
{
struct qede_reload_args args;
+ if (prog && prog->xdp_adjust_head) {
+ DP_ERR(edev, "Does not support bpf_xdp_adjust_head()\n");
+ return -EOPNOTSUPP;
+ }
+
/* If we're called, there was already a bpf reference increment */
args.func = &qede_xdp_reload_func;
args.u.new_prog = prog;
diff --git a/include/linux/filter.h b/include/linux/filter.h
index f078d2b1cff6..6a1658308612 100644
--- a/include/linux/filter.h
+++ b/include/linux/filter.h
@@ -406,7 +406,8 @@ struct bpf_prog {
u16 jited:1, /* Is our filter JIT'ed? */
gpl_compatible:1, /* Is filter GPL compatible? */
cb_access:1, /* Is control block accessed? */
- dst_needed:1; /* Do we need dst entry? */
+ dst_needed:1, /* Do we need dst entry? */
+ xdp_adjust_head:1; /* Adjusting pkt head? */
kmemcheck_bitfield_end(meta);
enum bpf_prog_type type; /* Type of BPF program */
u32 len; /* Number of filter blocks */
@@ -440,6 +441,7 @@ struct bpf_skb_data_end {
struct xdp_buff {
void *data;
void *data_end;
+ void *data_hard_start;
};
/* compute the linear packet data range [data, data_end) which
@@ -595,7 +597,7 @@ void sk_filter_uncharge(struct sock *sk, struct sk_filter *fp);
u64 __bpf_call_base(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5);
struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog);
-bool bpf_helper_changes_skb_data(void *func);
+bool bpf_helper_changes_pkt_data(void *func);
struct bpf_prog *bpf_patch_insn_single(struct bpf_prog *prog, u32 off,
const struct bpf_insn *patch, u32 len);
diff --git a/include/uapi/linux/bpf.h b/include/uapi/linux/bpf.h
index 6123d9b8e828..0eb0e87dbe9f 100644
--- a/include/uapi/linux/bpf.h
+++ b/include/uapi/linux/bpf.h
@@ -424,6 +424,12 @@ union bpf_attr {
* @len: length of header to be pushed in front
* @flags: Flags (unused for now)
* Return: 0 on success or negative error
+ *
+ * int bpf_xdp_adjust_head(xdp_md, delta)
+ * Adjust the xdp_md.data by delta
+ * @xdp_md: pointer to xdp_md
+ * @delta: An positive/negative integer to be added to xdp_md.data
+ * Return: 0 on success or negative on error
*/
#define __BPF_FUNC_MAPPER(FN) \
FN(unspec), \
@@ -469,7 +475,8 @@ union bpf_attr {
FN(csum_update), \
FN(set_hash_invalid), \
FN(get_numa_node_id), \
- FN(skb_change_head),
+ FN(skb_change_head), \
+ FN(xdp_adjust_head),
/* integer value in 'imm' field of BPF_CALL instruction selects which helper
* function eBPF program intends to call
@@ -576,6 +583,8 @@ struct bpf_sock {
__u32 protocol;
};
+#define XDP_PACKET_HEADROOM 256
+
/* User return codes for XDP prog type.
* A valid XDP program must return one of these defined values. All other
* return codes are reserved for future use. Unknown return codes will result
diff --git a/kernel/bpf/core.c b/kernel/bpf/core.c
index bdcc9f4ba767..83e0d153b0b4 100644
--- a/kernel/bpf/core.c
+++ b/kernel/bpf/core.c
@@ -1143,7 +1143,7 @@ struct bpf_prog * __weak bpf_int_jit_compile(struct bpf_prog *prog)
return prog;
}
-bool __weak bpf_helper_changes_skb_data(void *func)
+bool __weak bpf_helper_changes_pkt_data(void *func)
{
return false;
}
diff --git a/kernel/bpf/syscall.c b/kernel/bpf/syscall.c
index c0d2b423ce93..add93ecd7e69 100644
--- a/kernel/bpf/syscall.c
+++ b/kernel/bpf/syscall.c
@@ -579,6 +579,8 @@ static void fixup_bpf_calls(struct bpf_prog *prog)
prog->dst_needed = 1;
if (insn->imm == BPF_FUNC_get_prandom_u32)
bpf_user_rnd_init_once();
+ if (insn->imm == BPF_FUNC_xdp_adjust_head)
+ prog->xdp_adjust_head = 1;
if (insn->imm == BPF_FUNC_tail_call) {
/* mark bpf_tail_call as different opcode
* to avoid conditional branch in
diff --git a/kernel/bpf/verifier.c b/kernel/bpf/verifier.c
index cb37339ca0da..f5fa326518c9 100644
--- a/kernel/bpf/verifier.c
+++ b/kernel/bpf/verifier.c
@@ -1216,7 +1216,7 @@ static int check_call(struct bpf_verifier_env *env, int func_id)
return -EINVAL;
}
- changes_data = bpf_helper_changes_skb_data(fn->func);
+ changes_data = bpf_helper_changes_pkt_data(fn->func);
memset(&meta, 0, sizeof(meta));
meta.pkt_access = fn->pkt_access;
diff --git a/net/core/filter.c b/net/core/filter.c
index b751202e12f8..b1461708a977 100644
--- a/net/core/filter.c
+++ b/net/core/filter.c
@@ -2234,7 +2234,28 @@ static const struct bpf_func_proto bpf_skb_change_head_proto = {
.arg3_type = ARG_ANYTHING,
};
-bool bpf_helper_changes_skb_data(void *func)
+BPF_CALL_2(bpf_xdp_adjust_head, struct xdp_buff *, xdp, int, offset)
+{
+ void *data = xdp->data + offset;
+
+ if (unlikely(data < xdp->data_hard_start ||
+ data > xdp->data_end - ETH_HLEN))
+ return -EINVAL;
+
+ xdp->data = data;
+
+ return 0;
+}
+
+static const struct bpf_func_proto bpf_xdp_adjust_head_proto = {
+ .func = bpf_xdp_adjust_head,
+ .gpl_only = false,
+ .ret_type = RET_INTEGER,
+ .arg1_type = ARG_PTR_TO_CTX,
+ .arg2_type = ARG_ANYTHING,
+};
+
+bool bpf_helper_changes_pkt_data(void *func)
{
if (func == bpf_skb_vlan_push ||
func == bpf_skb_vlan_pop ||
@@ -2244,7 +2265,8 @@ bool bpf_helper_changes_skb_data(void *func)
func == bpf_skb_change_tail ||
func == bpf_skb_pull_data ||
func == bpf_l3_csum_replace ||
- func == bpf_l4_csum_replace)
+ func == bpf_l4_csum_replace ||
+ func == bpf_xdp_adjust_head)
return true;
return false;
@@ -2670,6 +2692,8 @@ xdp_func_proto(enum bpf_func_id func_id)
return &bpf_xdp_event_output_proto;
case BPF_FUNC_get_smp_processor_id:
return &bpf_get_smp_processor_id_proto;
+ case BPF_FUNC_xdp_adjust_head:
+ return &bpf_xdp_adjust_head_proto;
default:
return sk_filter_func_proto(func_id);
}
--
2.5.1
^ permalink raw reply related
* [PATCH v4 net-next 4/4] bpf: xdp: Add XDP example for head adjustment
From: Martin KaFai Lau @ 2016-12-07 23:53 UTC (permalink / raw)
To: netdev
Cc: Alexei Starovoitov, Brenden Blanco, Daniel Borkmann, David Miller,
Jakub Kicinski, Jesper Dangaard Brouer, John Fastabend,
Saeed Mahameed, Tariq Toukan, Kernel Team
In-Reply-To: <1481154794-2311034-1-git-send-email-kafai@fb.com>
The XDP prog checks if the incoming packet matches any VIP:PORT
combination in the BPF hashmap. If it is, it will encapsulate
the packet with a IPv4/v6 header as instructed by the value of
the BPF hashmap and then XDP_TX it out.
The VIP:PORT -> IP-Encap-Info can be specified by the cmd args
of the user prog.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
---
samples/bpf/Makefile | 4 +
samples/bpf/bpf_helpers.h | 2 +
samples/bpf/bpf_load.c | 94 +++++++++++++
samples/bpf/bpf_load.h | 1 +
samples/bpf/xdp1_user.c | 93 -------------
samples/bpf/xdp_tx_iptunnel_common.h | 37 +++++
samples/bpf/xdp_tx_iptunnel_kern.c | 236 ++++++++++++++++++++++++++++++++
samples/bpf/xdp_tx_iptunnel_user.c | 256 +++++++++++++++++++++++++++++++++++
8 files changed, 630 insertions(+), 93 deletions(-)
create mode 100644 samples/bpf/xdp_tx_iptunnel_common.h
create mode 100644 samples/bpf/xdp_tx_iptunnel_kern.c
create mode 100644 samples/bpf/xdp_tx_iptunnel_user.c
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 00cd3081c038..f2219c1489e5 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -33,6 +33,7 @@ hostprogs-y += trace_event
hostprogs-y += sampleip
hostprogs-y += tc_l2_redirect
hostprogs-y += lwt_len_hist
+hostprogs-y += xdp_tx_iptunnel
test_lru_dist-objs := test_lru_dist.o libbpf.o
sock_example-objs := sock_example.o libbpf.o
@@ -67,6 +68,7 @@ trace_event-objs := bpf_load.o libbpf.o trace_event_user.o
sampleip-objs := bpf_load.o libbpf.o sampleip_user.o
tc_l2_redirect-objs := bpf_load.o libbpf.o tc_l2_redirect_user.o
lwt_len_hist-objs := bpf_load.o libbpf.o lwt_len_hist_user.o
+xdp_tx_iptunnel-objs := bpf_load.o libbpf.o xdp_tx_iptunnel_user.o
# Tell kbuild to always build the programs
always := $(hostprogs-y)
@@ -99,6 +101,7 @@ always += test_current_task_under_cgroup_kern.o
always += trace_event_kern.o
always += sampleip_kern.o
always += lwt_len_hist_kern.o
+always += xdp_tx_iptunnel_kern.o
HOSTCFLAGS += -I$(objtree)/usr/include
HOSTCFLAGS += -I$(srctree)/tools/testing/selftests/bpf/
@@ -129,6 +132,7 @@ HOSTLOADLIBES_trace_event += -lelf
HOSTLOADLIBES_sampleip += -lelf
HOSTLOADLIBES_tc_l2_redirect += -l elf
HOSTLOADLIBES_lwt_len_hist += -l elf
+HOSTLOADLIBES_xdp_tx_iptunnel += -lelf
# Allows pointing LLC/CLANG to a LLVM backend with bpf support, redefine on cmdline:
# make samples/bpf/ LLC=~/git/llvm/build/bin/llc CLANG=~/git/llvm/build/bin/clang
diff --git a/samples/bpf/bpf_helpers.h b/samples/bpf/bpf_helpers.h
index 8370a6e3839d..faaffe2e139a 100644
--- a/samples/bpf/bpf_helpers.h
+++ b/samples/bpf/bpf_helpers.h
@@ -57,6 +57,8 @@ static int (*bpf_skb_set_tunnel_opt)(void *ctx, void *md, int size) =
(void *) BPF_FUNC_skb_set_tunnel_opt;
static unsigned long long (*bpf_get_prandom_u32)(void) =
(void *) BPF_FUNC_get_prandom_u32;
+static int (*bpf_xdp_adjust_head)(void *ctx, int offset) =
+ (void *) BPF_FUNC_xdp_adjust_head;
/* llvm builtin functions that eBPF C program may use to
* emit BPF_LD_ABS and BPF_LD_IND instructions
diff --git a/samples/bpf/bpf_load.c b/samples/bpf/bpf_load.c
index 49b45ccbe153..e30b6de94f2e 100644
--- a/samples/bpf/bpf_load.c
+++ b/samples/bpf/bpf_load.c
@@ -12,6 +12,10 @@
#include <linux/bpf.h>
#include <linux/filter.h>
#include <linux/perf_event.h>
+#include <linux/netlink.h>
+#include <linux/rtnetlink.h>
+#include <sys/types.h>
+#include <sys/socket.h>
#include <sys/syscall.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
@@ -450,3 +454,93 @@ struct ksym *ksym_search(long key)
/* out of range. return _stext */
return &syms[0];
}
+
+int set_link_xdp_fd(int ifindex, int fd)
+{
+ struct sockaddr_nl sa;
+ int sock, seq = 0, len, ret = -1;
+ char buf[4096];
+ struct nlattr *nla, *nla_xdp;
+ struct {
+ struct nlmsghdr nh;
+ struct ifinfomsg ifinfo;
+ char attrbuf[64];
+ } req;
+ struct nlmsghdr *nh;
+ struct nlmsgerr *err;
+
+ memset(&sa, 0, sizeof(sa));
+ sa.nl_family = AF_NETLINK;
+
+ sock = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
+ if (sock < 0) {
+ printf("open netlink socket: %s\n", strerror(errno));
+ return -1;
+ }
+
+ if (bind(sock, (struct sockaddr *)&sa, sizeof(sa)) < 0) {
+ printf("bind to netlink: %s\n", strerror(errno));
+ goto cleanup;
+ }
+
+ memset(&req, 0, sizeof(req));
+ req.nh.nlmsg_len = NLMSG_LENGTH(sizeof(struct ifinfomsg));
+ req.nh.nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK;
+ req.nh.nlmsg_type = RTM_SETLINK;
+ req.nh.nlmsg_pid = 0;
+ req.nh.nlmsg_seq = ++seq;
+ req.ifinfo.ifi_family = AF_UNSPEC;
+ req.ifinfo.ifi_index = ifindex;
+ nla = (struct nlattr *)(((char *)&req)
+ + NLMSG_ALIGN(req.nh.nlmsg_len));
+ nla->nla_type = NLA_F_NESTED | 43/*IFLA_XDP*/;
+
+ nla_xdp = (struct nlattr *)((char *)nla + NLA_HDRLEN);
+ nla_xdp->nla_type = 1/*IFLA_XDP_FD*/;
+ nla_xdp->nla_len = NLA_HDRLEN + sizeof(int);
+ memcpy((char *)nla_xdp + NLA_HDRLEN, &fd, sizeof(fd));
+ nla->nla_len = NLA_HDRLEN + nla_xdp->nla_len;
+
+ req.nh.nlmsg_len += NLA_ALIGN(nla->nla_len);
+
+ if (send(sock, &req, req.nh.nlmsg_len, 0) < 0) {
+ printf("send to netlink: %s\n", strerror(errno));
+ goto cleanup;
+ }
+
+ len = recv(sock, buf, sizeof(buf), 0);
+ if (len < 0) {
+ printf("recv from netlink: %s\n", strerror(errno));
+ goto cleanup;
+ }
+
+ for (nh = (struct nlmsghdr *)buf; NLMSG_OK(nh, len);
+ nh = NLMSG_NEXT(nh, len)) {
+ if (nh->nlmsg_pid != getpid()) {
+ printf("Wrong pid %d, expected %d\n",
+ nh->nlmsg_pid, getpid());
+ goto cleanup;
+ }
+ if (nh->nlmsg_seq != seq) {
+ printf("Wrong seq %d, expected %d\n",
+ nh->nlmsg_seq, seq);
+ goto cleanup;
+ }
+ switch (nh->nlmsg_type) {
+ case NLMSG_ERROR:
+ err = (struct nlmsgerr *)NLMSG_DATA(nh);
+ if (!err->error)
+ continue;
+ printf("nlmsg error %s\n", strerror(-err->error));
+ goto cleanup;
+ case NLMSG_DONE:
+ break;
+ }
+ }
+
+ ret = 0;
+
+cleanup:
+ close(sock);
+ return ret;
+}
diff --git a/samples/bpf/bpf_load.h b/samples/bpf/bpf_load.h
index 4adeeef53ad6..fb46a421ab41 100644
--- a/samples/bpf/bpf_load.h
+++ b/samples/bpf/bpf_load.h
@@ -31,4 +31,5 @@ struct ksym {
int load_kallsyms(void);
struct ksym *ksym_search(long key);
+int set_link_xdp_fd(int ifindex, int fd);
#endif
diff --git a/samples/bpf/xdp1_user.c b/samples/bpf/xdp1_user.c
index 2b2150d6d6f7..5f040a0d7712 100644
--- a/samples/bpf/xdp1_user.c
+++ b/samples/bpf/xdp1_user.c
@@ -5,111 +5,18 @@
* License as published by the Free Software Foundation.
*/
#include <linux/bpf.h>
-#include <linux/netlink.h>
-#include <linux/rtnetlink.h>
#include <assert.h>
#include <errno.h>
#include <signal.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
-#include <sys/socket.h>
#include <unistd.h>
#include "bpf_load.h"
#include "bpf_util.h"
#include "libbpf.h"
-static int set_link_xdp_fd(int ifindex, int fd)
-{
- struct sockaddr_nl sa;
- int sock, seq = 0, len, ret = -1;
- char buf[4096];
- struct nlattr *nla, *nla_xdp;
- struct {
- struct nlmsghdr nh;
- struct ifinfomsg ifinfo;
- char attrbuf[64];
- } req;
- struct nlmsghdr *nh;
- struct nlmsgerr *err;
-
- memset(&sa, 0, sizeof(sa));
- sa.nl_family = AF_NETLINK;
-
- sock = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
- if (sock < 0) {
- printf("open netlink socket: %s\n", strerror(errno));
- return -1;
- }
-
- if (bind(sock, (struct sockaddr *)&sa, sizeof(sa)) < 0) {
- printf("bind to netlink: %s\n", strerror(errno));
- goto cleanup;
- }
-
- memset(&req, 0, sizeof(req));
- req.nh.nlmsg_len = NLMSG_LENGTH(sizeof(struct ifinfomsg));
- req.nh.nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK;
- req.nh.nlmsg_type = RTM_SETLINK;
- req.nh.nlmsg_pid = 0;
- req.nh.nlmsg_seq = ++seq;
- req.ifinfo.ifi_family = AF_UNSPEC;
- req.ifinfo.ifi_index = ifindex;
- nla = (struct nlattr *)(((char *)&req)
- + NLMSG_ALIGN(req.nh.nlmsg_len));
- nla->nla_type = NLA_F_NESTED | 43/*IFLA_XDP*/;
-
- nla_xdp = (struct nlattr *)((char *)nla + NLA_HDRLEN);
- nla_xdp->nla_type = 1/*IFLA_XDP_FD*/;
- nla_xdp->nla_len = NLA_HDRLEN + sizeof(int);
- memcpy((char *)nla_xdp + NLA_HDRLEN, &fd, sizeof(fd));
- nla->nla_len = NLA_HDRLEN + nla_xdp->nla_len;
-
- req.nh.nlmsg_len += NLA_ALIGN(nla->nla_len);
-
- if (send(sock, &req, req.nh.nlmsg_len, 0) < 0) {
- printf("send to netlink: %s\n", strerror(errno));
- goto cleanup;
- }
-
- len = recv(sock, buf, sizeof(buf), 0);
- if (len < 0) {
- printf("recv from netlink: %s\n", strerror(errno));
- goto cleanup;
- }
-
- for (nh = (struct nlmsghdr *)buf; NLMSG_OK(nh, len);
- nh = NLMSG_NEXT(nh, len)) {
- if (nh->nlmsg_pid != getpid()) {
- printf("Wrong pid %d, expected %d\n",
- nh->nlmsg_pid, getpid());
- goto cleanup;
- }
- if (nh->nlmsg_seq != seq) {
- printf("Wrong seq %d, expected %d\n",
- nh->nlmsg_seq, seq);
- goto cleanup;
- }
- switch (nh->nlmsg_type) {
- case NLMSG_ERROR:
- err = (struct nlmsgerr *)NLMSG_DATA(nh);
- if (!err->error)
- continue;
- printf("nlmsg error %s\n", strerror(-err->error));
- goto cleanup;
- case NLMSG_DONE:
- break;
- }
- }
-
- ret = 0;
-
-cleanup:
- close(sock);
- return ret;
-}
-
static int ifindex;
static void int_exit(int sig)
diff --git a/samples/bpf/xdp_tx_iptunnel_common.h b/samples/bpf/xdp_tx_iptunnel_common.h
new file mode 100644
index 000000000000..dd12cc35110f
--- /dev/null
+++ b/samples/bpf/xdp_tx_iptunnel_common.h
@@ -0,0 +1,37 @@
+/* Copyright (c) 2016 Facebook
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of version 2 of the GNU General Public
+ * License as published by the Free Software Foundation.
+ */
+#ifndef _SAMPLES_BPF_XDP_TX_IPTNL_COMMON_H
+#define _SAMPLES_BPF_XDP_TX_IPTNL_COMMON_H
+
+#include <linux/types.h>
+
+#define MAX_IPTNL_ENTRIES 256U
+
+struct vip {
+ union {
+ __u32 v6[4];
+ __u32 v4;
+ } daddr;
+ __u16 dport;
+ __u16 family;
+ __u8 protocol;
+};
+
+struct iptnl_info {
+ union {
+ __u32 v6[4];
+ __u32 v4;
+ } saddr;
+ union {
+ __u32 v6[4];
+ __u32 v4;
+ } daddr;
+ __u16 family;
+ __u8 dmac[6];
+};
+
+#endif
diff --git a/samples/bpf/xdp_tx_iptunnel_kern.c b/samples/bpf/xdp_tx_iptunnel_kern.c
new file mode 100644
index 000000000000..85c38ecd3a2d
--- /dev/null
+++ b/samples/bpf/xdp_tx_iptunnel_kern.c
@@ -0,0 +1,236 @@
+/* Copyright (c) 2016 Facebook
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of version 2 of the GNU General Public
+ * License as published by the Free Software Foundation.
+ *
+ * This program shows how to use bpf_xdp_adjust_head() by
+ * encapsulating the incoming packet in an IPv4/v6 header
+ * and then XDP_TX it out.
+ */
+#include <uapi/linux/bpf.h>
+#include <linux/in.h>
+#include <linux/if_ether.h>
+#include <linux/if_packet.h>
+#include <linux/if_vlan.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include "bpf_helpers.h"
+#include "xdp_tx_iptunnel_common.h"
+
+struct bpf_map_def SEC("maps") rxcnt = {
+ .type = BPF_MAP_TYPE_PERCPU_ARRAY,
+ .key_size = sizeof(__u32),
+ .value_size = sizeof(__u64),
+ .max_entries = 256,
+};
+
+struct bpf_map_def SEC("maps") vip2tnl = {
+ .type = BPF_MAP_TYPE_HASH,
+ .key_size = sizeof(struct vip),
+ .value_size = sizeof(struct iptnl_info),
+ .max_entries = MAX_IPTNL_ENTRIES,
+};
+
+static __always_inline void count_tx(u32 protocol)
+{
+ u64 *rxcnt_count;
+
+ rxcnt_count = bpf_map_lookup_elem(&rxcnt, &protocol);
+ if (rxcnt_count)
+ *rxcnt_count += 1;
+}
+
+static __always_inline int get_dport(void *trans_data, void *data_end,
+ u8 protocol)
+{
+ struct tcphdr *th;
+ struct udphdr *uh;
+
+ switch (protocol) {
+ case IPPROTO_TCP:
+ th = (struct tcphdr *)trans_data;
+ if (th + 1 > data_end)
+ return -1;
+ return th->dest;
+ case IPPROTO_UDP:
+ uh = (struct udphdr *)trans_data;
+ if (uh + 1 > data_end)
+ return -1;
+ return uh->dest;
+ default:
+ return 0;
+ }
+}
+
+static __always_inline void set_ethhdr(struct ethhdr *new_eth,
+ const struct ethhdr *old_eth,
+ const struct iptnl_info *tnl,
+ __be16 h_proto)
+{
+ memcpy(new_eth->h_source, old_eth->h_dest, sizeof(new_eth->h_source));
+ memcpy(new_eth->h_dest, tnl->dmac, sizeof(new_eth->h_dest));
+ new_eth->h_proto = h_proto;
+}
+
+static __always_inline int handle_ipv4(struct xdp_md *xdp)
+{
+ void *data_end = (void *)(long)xdp->data_end;
+ void *data = (void *)(long)xdp->data;
+ struct iptnl_info *tnl;
+ struct ethhdr *new_eth;
+ struct ethhdr *old_eth;
+ struct iphdr *iph = data + sizeof(struct ethhdr);
+ u16 *next_iph_u16;
+ u16 payload_len;
+ struct vip vip = {};
+ int dport;
+ u32 csum = 0;
+ int i;
+
+ if (iph + 1 > data_end)
+ return XDP_DROP;
+
+ dport = get_dport(iph + 1, data_end, iph->protocol);
+ if (dport == -1)
+ return XDP_DROP;
+
+ vip.protocol = iph->protocol;
+ vip.family = AF_INET;
+ vip.daddr.v4 = iph->daddr;
+ vip.dport = dport;
+ payload_len = ntohs(iph->tot_len);
+
+ tnl = bpf_map_lookup_elem(&vip2tnl, &vip);
+ /* It only does v4-in-v4 */
+ if (!tnl || tnl->family != AF_INET)
+ return XDP_PASS;
+
+ /* The vip key is found. Add an IP header and send it out */
+
+ if (bpf_xdp_adjust_head(xdp, 0 - (int)sizeof(struct iphdr)))
+ return XDP_DROP;
+
+ data = (void *)(long)xdp->data;
+ data_end = (void *)(long)xdp->data_end;
+
+ new_eth = data;
+ iph = data + sizeof(*new_eth);
+ old_eth = data + sizeof(*iph);
+
+ if (new_eth + 1 > data_end ||
+ old_eth + 1 > data_end ||
+ iph + 1 > data_end)
+ return XDP_DROP;
+
+ set_ethhdr(new_eth, old_eth, tnl, htons(ETH_P_IP));
+
+ iph->version = 4;
+ iph->ihl = sizeof(*iph) >> 2;
+ iph->frag_off = 0;
+ iph->protocol = IPPROTO_IPIP;
+ iph->check = 0;
+ iph->tos = 0;
+ iph->tot_len = htons(payload_len + sizeof(*iph));
+ iph->daddr = tnl->daddr.v4;
+ iph->saddr = tnl->saddr.v4;
+ iph->ttl = 8;
+
+ next_iph_u16 = (u16 *)iph;
+#pragma clang loop unroll(full)
+ for (i = 0; i < sizeof(*iph) >> 1; i++)
+ csum += *next_iph_u16++;
+
+ iph->check = ~((csum & 0xffff) + (csum >> 16));
+
+ count_tx(vip.protocol);
+
+ return XDP_TX;
+}
+
+static __always_inline int handle_ipv6(struct xdp_md *xdp)
+{
+ void *data_end = (void *)(long)xdp->data_end;
+ void *data = (void *)(long)xdp->data;
+ struct iptnl_info *tnl;
+ struct ethhdr *new_eth;
+ struct ethhdr *old_eth;
+ struct ipv6hdr *ip6h = data + sizeof(struct ethhdr);
+ __u16 payload_len;
+ struct vip vip = {};
+ int dport;
+
+ if (ip6h + 1 > data_end)
+ return XDP_DROP;
+
+ dport = get_dport(ip6h + 1, data_end, ip6h->nexthdr);
+ if (dport == -1)
+ return XDP_DROP;
+
+ vip.protocol = ip6h->nexthdr;
+ vip.family = AF_INET6;
+ memcpy(vip.daddr.v6, ip6h->daddr.s6_addr32, sizeof(vip.daddr));
+ vip.dport = dport;
+ payload_len = ip6h->payload_len;
+
+ tnl = bpf_map_lookup_elem(&vip2tnl, &vip);
+ /* It only does v6-in-v6 */
+ if (!tnl || tnl->family != AF_INET6)
+ return XDP_PASS;
+
+ /* The vip key is found. Add an IP header and send it out */
+
+ if (bpf_xdp_adjust_head(xdp, 0 - (int)sizeof(struct ipv6hdr)))
+ return XDP_DROP;
+
+ data = (void *)(long)xdp->data;
+ data_end = (void *)(long)xdp->data_end;
+
+ new_eth = data;
+ ip6h = data + sizeof(*new_eth);
+ old_eth = data + sizeof(*ip6h);
+
+ if (new_eth + 1 > data_end ||
+ old_eth + 1 > data_end ||
+ ip6h + 1 > data_end)
+ return XDP_DROP;
+
+ set_ethhdr(new_eth, old_eth, tnl, htons(ETH_P_IPV6));
+
+ ip6h->version = 6;
+ ip6h->priority = 0;
+ memset(ip6h->flow_lbl, 0, sizeof(ip6h->flow_lbl));
+ ip6h->payload_len = htons(ntohs(payload_len) + sizeof(*ip6h));
+ ip6h->nexthdr = IPPROTO_IPV6;
+ ip6h->hop_limit = 8;
+ memcpy(ip6h->saddr.s6_addr32, tnl->saddr.v6, sizeof(tnl->saddr.v6));
+ memcpy(ip6h->daddr.s6_addr32, tnl->daddr.v6, sizeof(tnl->daddr.v6));
+
+ count_tx(vip.protocol);
+
+ return XDP_TX;
+}
+
+SEC("xdp_tx_iptunnel")
+int _xdp_tx_iptunnel(struct xdp_md *xdp)
+{
+ void *data_end = (void *)(long)xdp->data_end;
+ void *data = (void *)(long)xdp->data;
+ struct ethhdr *eth = data;
+ __u16 h_proto;
+
+ if (eth + 1 > data_end)
+ return XDP_DROP;
+
+ h_proto = eth->h_proto;
+
+ if (h_proto == htons(ETH_P_IP))
+ return handle_ipv4(xdp);
+ else if (h_proto == htons(ETH_P_IPV6))
+
+ return handle_ipv6(xdp);
+ else
+ return XDP_PASS;
+}
+
+char _license[] SEC("license") = "GPL";
diff --git a/samples/bpf/xdp_tx_iptunnel_user.c b/samples/bpf/xdp_tx_iptunnel_user.c
new file mode 100644
index 000000000000..7a71f5c74684
--- /dev/null
+++ b/samples/bpf/xdp_tx_iptunnel_user.c
@@ -0,0 +1,256 @@
+/* Copyright (c) 2016 Facebook
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of version 2 of the GNU General Public
+ * License as published by the Free Software Foundation.
+ */
+#include <linux/bpf.h>
+#include <assert.h>
+#include <errno.h>
+#include <signal.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <sys/resource.h>
+#include <arpa/inet.h>
+#include <netinet/ether.h>
+#include <unistd.h>
+#include <time.h>
+#include "bpf_load.h"
+#include "libbpf.h"
+#include "bpf_util.h"
+#include "xdp_tx_iptunnel_common.h"
+
+#define STATS_INTERVAL_S 2U
+
+static int ifindex = -1;
+
+static void int_exit(int sig)
+{
+ if (ifindex > -1)
+ set_link_xdp_fd(ifindex, -1);
+ exit(0);
+}
+
+/* simple per-protocol drop counter
+ */
+static void poll_stats(unsigned int kill_after_s)
+{
+ const unsigned int nr_protos = 256;
+ unsigned int nr_cpus = bpf_num_possible_cpus();
+ time_t started_at = time(NULL);
+ __u64 values[nr_cpus], prev[nr_protos][nr_cpus];
+ __u32 proto;
+ int i;
+
+ memset(prev, 0, sizeof(prev));
+
+ while (!kill_after_s || time(NULL) - started_at <= kill_after_s) {
+ sleep(STATS_INTERVAL_S);
+
+ for (proto = 0; proto < nr_protos; proto++) {
+ __u64 sum = 0;
+
+ assert(bpf_lookup_elem(map_fd[0], &proto, values) == 0);
+ for (i = 0; i < nr_cpus; i++)
+ sum += (values[i] - prev[proto][i]);
+
+ if (sum)
+ printf("proto %u: sum:%10llu pkts, rate:%10llu pkts/s\n",
+ proto, sum, sum / STATS_INTERVAL_S);
+ memcpy(prev[proto], values, sizeof(values));
+ }
+ }
+}
+
+static void usage(const char *cmd)
+{
+ printf("Start a XDP prog which encapsulates incoming packets\n"
+ "in an IPv4/v6 header and XDP_TX it out. The dst <VIP:PORT>\n"
+ "is used to select packets to encapsulate\n\n");
+ printf("Usage: %s [...]\n", cmd);
+ printf(" -i <ifindex> Interface Index\n");
+ printf(" -a <vip-service-address> IPv4 or IPv6\n");
+ printf(" -p <vip-service-port> A port range (e.g. 433-444) is also allowed\n");
+ printf(" -s <source-ip> Used in the IPTunnel header\n");
+ printf(" -d <dest-ip> Used in the IPTunnel header\n");
+ printf(" -m <dest-MAC> Used in sending the IP Tunneled pkt\n");
+ printf(" -T <stop-after-X-seconds> Default: 0 (forever)\n");
+ printf(" -P <IP-Protocol> Default is TCP\n");
+ printf(" -h Display this help\n");
+}
+
+static int parse_ipstr(const char *ipstr, unsigned int *addr)
+{
+ if (inet_pton(AF_INET6, ipstr, addr) == 1) {
+ return AF_INET6;
+ } else if (inet_pton(AF_INET, ipstr, addr) == 1) {
+ addr[1] = addr[2] = addr[3] = 0;
+ return AF_INET;
+ }
+
+ fprintf(stderr, "%s is an invalid IP\n", ipstr);
+ return AF_UNSPEC;
+}
+
+static int parse_ports(const char *port_str, int *min_port, int *max_port)
+{
+ char *end;
+ long tmp_min_port;
+ long tmp_max_port;
+
+ tmp_min_port = strtol(optarg, &end, 10);
+ if (tmp_min_port < 1 || tmp_min_port > 65535) {
+ fprintf(stderr, "Invalid port(s):%s\n", optarg);
+ return 1;
+ }
+
+ if (*end == '-') {
+ end++;
+ tmp_max_port = strtol(end, NULL, 10);
+ if (tmp_max_port < 1 || tmp_max_port > 65535) {
+ fprintf(stderr, "Invalid port(s):%s\n", optarg);
+ return 1;
+ }
+ } else {
+ tmp_max_port = tmp_min_port;
+ }
+
+ if (tmp_min_port > tmp_max_port) {
+ fprintf(stderr, "Invalid port(s):%s\n", optarg);
+ return 1;
+ }
+
+ if (tmp_max_port - tmp_min_port + 1 > MAX_IPTNL_ENTRIES) {
+ fprintf(stderr, "Port range (%s) is larger than %u\n",
+ port_str, MAX_IPTNL_ENTRIES);
+ return 1;
+ }
+ *min_port = tmp_min_port;
+ *max_port = tmp_max_port;
+
+ return 0;
+}
+
+int main(int argc, char **argv)
+{
+ unsigned char opt_flags[256] = {};
+ unsigned int kill_after_s = 0;
+ const char *optstr = "i:a:p:s:d:m:T:P:h";
+ int min_port = 0, max_port = 0;
+ struct iptnl_info tnl = {};
+ struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
+ struct vip vip = {};
+ char filename[256];
+ int opt;
+ int i;
+
+ tnl.family = AF_UNSPEC;
+ vip.protocol = IPPROTO_TCP;
+
+ for (i = 0; i < strlen(optstr); i++)
+ if (optstr[i] != 'h' && 'a' <= optstr[i] && optstr[i] <= 'z')
+ opt_flags[(unsigned char)optstr[i]] = 1;
+
+ while ((opt = getopt(argc, argv, optstr)) != -1) {
+ unsigned short family;
+ unsigned int *v6;
+
+ switch (opt) {
+ case 'i':
+ ifindex = atoi(optarg);
+ break;
+ case 'a':
+ vip.family = parse_ipstr(optarg, vip.daddr.v6);
+ if (vip.family == AF_UNSPEC)
+ return 1;
+ break;
+ case 'p':
+ if (parse_ports(optarg, &min_port, &max_port))
+ return 1;
+ break;
+ case 'P':
+ vip.protocol = atoi(optarg);
+ break;
+ case 's':
+ case 'd':
+ if (opt == 's')
+ v6 = tnl.saddr.v6;
+ else
+ v6 = tnl.daddr.v6;
+
+ family = parse_ipstr(optarg, v6);
+ if (family == AF_UNSPEC)
+ return 1;
+ if (tnl.family == AF_UNSPEC) {
+ tnl.family = family;
+ } else if (tnl.family != family) {
+ fprintf(stderr,
+ "The IP version of the src and dst addresses used in the IP encapsulation does not match\n");
+ return 1;
+ }
+ break;
+ case 'm':
+ if (!ether_aton_r(optarg,
+ (struct ether_addr *)tnl.dmac)) {
+ fprintf(stderr, "Invalid mac address:%s\n",
+ optarg);
+ return 1;
+ }
+ break;
+ case 'T':
+ kill_after_s = atoi(optarg);
+ break;
+ default:
+ usage(argv[0]);
+ return 1;
+ }
+ opt_flags[opt] = 0;
+ }
+
+ for (i = 0; i < strlen(optstr); i++) {
+ if (opt_flags[(unsigned int)optstr[i]]) {
+ fprintf(stderr, "Missing argument -%c\n", optstr[i]);
+ usage(argv[0]);
+ return 1;
+ }
+ }
+
+ if (setrlimit(RLIMIT_MEMLOCK, &r)) {
+ perror("setrlimit(RLIMIT_MEMLOCK, RLIM_INFINITY)");
+ return 1;
+ }
+
+ snprintf(filename, sizeof(filename), "%s_kern.o", argv[0]);
+
+ if (load_bpf_file(filename)) {
+ printf("%s", bpf_log_buf);
+ return 1;
+ }
+
+ if (!prog_fd[0]) {
+ printf("load_bpf_file: %s\n", strerror(errno));
+ return 1;
+ }
+
+ signal(SIGINT, int_exit);
+
+ while (min_port <= max_port) {
+ vip.dport = htons(min_port++);
+ if (bpf_update_elem(map_fd[1], &vip, &tnl, BPF_NOEXIST)) {
+ perror("bpf_update_elem(&vip2tnl)");
+ return 1;
+ }
+ }
+
+ if (set_link_xdp_fd(ifindex, prog_fd[0]) < 0) {
+ printf("link set xdp fd failed\n");
+ return 1;
+ }
+
+ poll_stats(kill_after_s);
+
+ set_link_xdp_fd(ifindex, -1);
+
+ return 0;
+}
--
2.5.1
^ permalink raw reply related
* [PATCH v4 net-next 2/4] mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs
From: Martin KaFai Lau @ 2016-12-07 23:53 UTC (permalink / raw)
To: netdev
Cc: Alexei Starovoitov, Brenden Blanco, Daniel Borkmann, David Miller,
Jakub Kicinski, Jesper Dangaard Brouer, John Fastabend,
Saeed Mahameed, Tariq Toukan, Kernel Team
In-Reply-To: <1481154794-2311034-1-git-send-email-kafai@fb.com>
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
---
drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 28 +++++++++++-----
drivers/net/ethernet/mellanox/mlx4/en_rx.c | 46 ++++++++++++++------------
2 files changed, 44 insertions(+), 30 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index f441eda63bec..c97d25b06444 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -51,6 +51,8 @@
#include "mlx4_en.h"
#include "en_port.h"
+#define MLX4_EN_MAX_XDP_MTU ((int)(PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN)))
+
int mlx4_en_setup_tc(struct net_device *dev, u8 up)
{
struct mlx4_en_priv *priv = netdev_priv(dev);
@@ -2249,6 +2251,19 @@ void mlx4_en_destroy_netdev(struct net_device *dev)
free_netdev(dev);
}
+static bool mlx4_en_check_xdp_mtu(struct net_device *dev, int mtu)
+{
+ struct mlx4_en_priv *priv = netdev_priv(dev);
+
+ if (mtu > MLX4_EN_MAX_XDP_MTU) {
+ en_err(priv, "mtu:%d > max:%d when XDP prog is attached\n",
+ mtu, MLX4_EN_MAX_XDP_MTU);
+ return false;
+ }
+
+ return true;
+}
+
static int mlx4_en_change_mtu(struct net_device *dev, int new_mtu)
{
struct mlx4_en_priv *priv = netdev_priv(dev);
@@ -2258,11 +2273,10 @@ static int mlx4_en_change_mtu(struct net_device *dev, int new_mtu)
en_dbg(DRV, priv, "Change MTU called - current:%d new:%d\n",
dev->mtu, new_mtu);
- if (priv->tx_ring_num[TX_XDP] && MLX4_EN_EFF_MTU(new_mtu) > FRAG_SZ0) {
- en_err(priv, "MTU size:%d requires frags but XDP running\n",
- new_mtu);
- return -EOPNOTSUPP;
- }
+ if (priv->tx_ring_num[TX_XDP] &&
+ !mlx4_en_check_xdp_mtu(dev, new_mtu))
+ return -ENOTSUPP;
+
dev->mtu = new_mtu;
if (netif_running(dev)) {
@@ -2715,10 +2729,8 @@ static int mlx4_xdp_set(struct net_device *dev, struct bpf_prog *prog)
return 0;
}
- if (priv->num_frags > 1) {
- en_err(priv, "Cannot set XDP if MTU requires multiple frags\n");
+ if (!mlx4_en_check_xdp_mtu(dev, dev->mtu))
return -EOPNOTSUPP;
- }
tmp = kzalloc(sizeof(*tmp), GFP_KERNEL);
if (!tmp)
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_rx.c b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
index 6562f78b07f4..23e9d04d1ef4 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_rx.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
@@ -1164,37 +1164,39 @@ static const int frag_sizes[] = {
void mlx4_en_calc_rx_buf(struct net_device *dev)
{
- enum dma_data_direction dma_dir = PCI_DMA_FROMDEVICE;
struct mlx4_en_priv *priv = netdev_priv(dev);
int eff_mtu = MLX4_EN_EFF_MTU(dev->mtu);
- int order = MLX4_EN_ALLOC_PREFER_ORDER;
- u32 align = SMP_CACHE_BYTES;
- int buf_size = 0;
int i = 0;
/* bpf requires buffers to be set up as 1 packet per page.
* This only works when num_frags == 1.
*/
if (priv->tx_ring_num[TX_XDP]) {
- dma_dir = PCI_DMA_BIDIRECTIONAL;
- /* This will gain efficient xdp frame recycling at the expense
- * of more costly truesize accounting
+ priv->frag_info[0].order = 0;
+ priv->frag_info[0].frag_size = eff_mtu;
+ priv->frag_info[0].frag_prefix_size = 0;
+ /* This will gain efficient xdp frame recycling at the
+ * expense of more costly truesize accounting
*/
- align = PAGE_SIZE;
- order = 0;
- }
-
- while (buf_size < eff_mtu) {
- priv->frag_info[i].order = order;
- priv->frag_info[i].frag_size =
- (eff_mtu > buf_size + frag_sizes[i]) ?
- frag_sizes[i] : eff_mtu - buf_size;
- priv->frag_info[i].frag_prefix_size = buf_size;
- priv->frag_info[i].frag_stride =
- ALIGN(priv->frag_info[i].frag_size, align);
- priv->frag_info[i].dma_dir = dma_dir;
- buf_size += priv->frag_info[i].frag_size;
- i++;
+ priv->frag_info[0].frag_stride = PAGE_SIZE;
+ priv->frag_info[0].dma_dir = PCI_DMA_BIDIRECTIONAL;
+ i = 1;
+ } else {
+ int buf_size = 0;
+
+ while (buf_size < eff_mtu) {
+ priv->frag_info[i].order = MLX4_EN_ALLOC_PREFER_ORDER;
+ priv->frag_info[i].frag_size =
+ (eff_mtu > buf_size + frag_sizes[i]) ?
+ frag_sizes[i] : eff_mtu - buf_size;
+ priv->frag_info[i].frag_prefix_size = buf_size;
+ priv->frag_info[i].frag_stride =
+ ALIGN(priv->frag_info[i].frag_size,
+ SMP_CACHE_BYTES);
+ priv->frag_info[i].dma_dir = PCI_DMA_FROMDEVICE;
+ buf_size += priv->frag_info[i].frag_size;
+ i++;
+ }
}
priv->num_frags = i;
--
2.5.1
^ permalink raw reply related
* Re: [PATCH 2/2] net: ethernet: stmmac: remove private tx queue lock
From: David Miller @ 2016-12-07 23:41 UTC (permalink / raw)
To: pavel
Cc: LinoSanfilippo, bh74.an, ks.giri, vipul.pandya, peppe.cavallaro,
alexandre.torgue, linux-kernel, netdev
In-Reply-To: <20161207213757.GC2250@amd>
From: Pavel Machek <pavel@ucw.cz>
Date: Wed, 7 Dec 2016 22:37:57 +0100
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 982c952..7415bc2 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -1308,7 +1308,7 @@ static void stmmac_tx_clean(struct stmmac_priv *priv)
> unsigned int bytes_compl = 0, pkts_compl = 0;
> unsigned int entry = priv->dirty_tx;
>
> - spin_lock(&priv->tx_lock);
> + netif_tx_lock_bh(priv->dev);
>
> priv->xstats.tx_clean++;
>
stmmac_tx_clean() runs from either the timer or the NAPI poll handler,
both execute from software interrupts, therefore _bh() should be
unnecessary.
^ permalink raw reply
* Re: [PATCH 2/2] net: ethernet: stmmac: remove private tx queue lock
From: Pavel Machek @ 2016-12-07 23:21 UTC (permalink / raw)
To: Lino Sanfilippo
Cc: bh74.an, ks.giri, vipul.pandya, peppe.cavallaro, alexandre.torgue,
davem, linux-kernel, netdev
In-Reply-To: <afcae723-5804-305f-2756-c4dbf9045943@gmx.de>
[-- Attachment #1: Type: text/plain, Size: 1945 bytes --]
On Wed 2016-12-07 23:34:19, Lino Sanfilippo wrote:
> On 07.12.2016 22:43, Lino Sanfilippo wrote:
> > Hi Pavel,
> >
> > On 07.12.2016 22:37, Pavel Machek wrote:
> >> On Wed 2016-12-07 21:05:38, Lino Sanfilippo wrote:
> >>> The driver uses a private lock for synchronization between the xmit
> >>> function and the xmit completion handler, but since the NETIF_F_LLTX flag
> >>> is not set, the xmit function is also called with the xmit_lock held.
> >>>
> >>> On the other hand the xmit completion handler first takes the private lock
> >>> and (in case that the tx queue has been stopped) the xmit_lock, leading to
> >>> a reverse locking order and the potential danger of a deadlock.
> >>>
> >>> Fix this by removing the private lock completely and synchronizing the xmit
> >>> function and completion handler solely by means of the xmit_lock. By doing
> >>> this remove also the now unnecessary double check for a stopped tx queue.
> >>>
> >>
> >> FYI, here's modified version. I believe _bh versions are needed, and
> >> I'm testing that version now. (Oh and I also ported it to net-next).
> >>
> >> It survived 30 minutes of testing so far...
> >>
> >
> > First off, thanks for testing.
> > Hmm. I dont understand why _bh would be needed. We call that function from
> > BH context only (napi poll and timer).
> > Any idea?
> >
>
> Could this once again be caused by irq coalescing? When the tx queue has been stopped
> the cleanup handler has to wakeup the queue within a certain time span, otherwise the
> watchdog will complain (as it happened in your test). Could you retest this with
> irq coalescing disabled?
I actually had TX coalescing disabled, with
-#define STMMAC_TX_FRAMES 64
+#define STMMAC_TX_FRAMES 0
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]
^ permalink raw reply
* Re: [PATCH 1/2] net: ethernet: sxgbe: remove private tx queue lock
From: Francois Romieu @ 2016-12-07 23:15 UTC (permalink / raw)
To: Lino Sanfilippo
Cc: bh74.an, ks.giri, vipul.pandya, peppe.cavallaro, alexandre.torgue,
pavel, davem, linux-kernel, netdev
In-Reply-To: <1481141138-19466-2-git-send-email-LinoSanfilippo@gmx.de>
Lino Sanfilippo <LinoSanfilippo@gmx.de> :
> The driver uses a private lock for synchronization between the xmit
> function and the xmit completion handler, but since the NETIF_F_LLTX flag
> is not set, the xmit function is also called with the xmit_lock held.
>
> On the other hand the xmit completion handler first takes the private lock
> and (in case that the tx queue has been stopped) the xmit_lock, leading
> to a reverse locking order and the potential danger of a deadlock.
netif_tx_stop_queue is used by:
1. xmit function before releasing lock and returning.
2. sxgbe_restart_tx_queue()
<- sxgbe_tx_interrupt
<- sxgbe_reset_all_tx_queues()
<- sxgbe_tx_timeout()
Given xmit won't be called again until tx queue is enabled, it's not clear
how a deadlock could happen due to #1.
Regardless of deadlocks anywhere else, #2 has some serious problem due to
the lack of exclusion between the tx queue restart handler and the xmit
handler.
--
Ueimor
^ permalink raw reply
* Re: [PATCH 2/2] net: ethernet: stmmac: remove private tx queue lock
From: Lino Sanfilippo @ 2016-12-07 22:34 UTC (permalink / raw)
To: Pavel Machek
Cc: bh74.an, ks.giri, vipul.pandya, peppe.cavallaro, alexandre.torgue,
davem, linux-kernel, netdev
In-Reply-To: <cc10a750-b8ef-a600-4cd5-5b51904c5253@gmx.de>
On 07.12.2016 22:43, Lino Sanfilippo wrote:
> Hi Pavel,
>
> On 07.12.2016 22:37, Pavel Machek wrote:
>> On Wed 2016-12-07 21:05:38, Lino Sanfilippo wrote:
>>> The driver uses a private lock for synchronization between the xmit
>>> function and the xmit completion handler, but since the NETIF_F_LLTX flag
>>> is not set, the xmit function is also called with the xmit_lock held.
>>>
>>> On the other hand the xmit completion handler first takes the private lock
>>> and (in case that the tx queue has been stopped) the xmit_lock, leading to
>>> a reverse locking order and the potential danger of a deadlock.
>>>
>>> Fix this by removing the private lock completely and synchronizing the xmit
>>> function and completion handler solely by means of the xmit_lock. By doing
>>> this remove also the now unnecessary double check for a stopped tx queue.
>>>
>>
>> FYI, here's modified version. I believe _bh versions are needed, and
>> I'm testing that version now. (Oh and I also ported it to net-next).
>>
>> It survived 30 minutes of testing so far...
>>
>
> First off, thanks for testing.
> Hmm. I dont understand why _bh would be needed. We call that function from
> BH context only (napi poll and timer).
> Any idea?
>
Could this once again be caused by irq coalescing? When the tx queue has been stopped
the cleanup handler has to wakeup the queue within a certain time span, otherwise the
watchdog will complain (as it happened in your test). Could you retest this with
irq coalescing disabled?
^ permalink raw reply
* [net-next v2 18/19] i40e: use (add|rm)_vlan_all_mac helper functions when changing PVID
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e.h | 2 +
drivers/net/ethernet/intel/i40e/i40e_main.c | 4 +-
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c | 43 ++++++++++++++--------
3 files changed, 32 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index f1d838f..ba8d309 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -852,7 +852,9 @@ int i40e_open(struct net_device *netdev);
int i40e_close(struct net_device *netdev);
int i40e_vsi_open(struct i40e_vsi *vsi);
void i40e_vlan_stripping_disable(struct i40e_vsi *vsi);
+int i40e_add_vlan_all_mac(struct i40e_vsi *vsi, s16 vid);
int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid);
+void i40e_rm_vlan_all_mac(struct i40e_vsi *vsi, s16 vid);
void i40e_vsi_kill_vlan(struct i40e_vsi *vsi, s16 vid);
struct i40e_mac_filter *i40e_put_mac_in_vlan(struct i40e_vsi *vsi,
const u8 *macaddr);
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 8aedfb7..49261cc 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -2505,7 +2505,7 @@ static void i40e_vlan_rx_register(struct net_device *netdev, u32 features)
* NOTE: this function expects to be called while under the
* mac_filter_hash_lock
**/
-static int i40e_add_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
+int i40e_add_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
{
struct i40e_mac_filter *f, *add_f;
struct hlist_node *h;
@@ -2596,7 +2596,7 @@ int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
* NOTE: this function expects to be called while under the
* mac_filter_hash_lock
*/
-static void i40e_rm_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
+void i40e_rm_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
{
struct i40e_mac_filter *f;
struct hlist_node *h;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
index d28b684..a6198b7 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -2766,7 +2766,6 @@ int i40e_ndo_set_vf_port_vlan(struct net_device *netdev, int vf_id,
u16 vlanprio = vlan_id | (qos << I40E_VLAN_PRIORITY_SHIFT);
struct i40e_netdev_priv *np = netdev_priv(netdev);
struct i40e_pf *pf = np->vsi->back;
- bool is_vsi_in_vlan = false;
struct i40e_vsi *vsi;
struct i40e_vf *vf;
int ret = 0;
@@ -2803,11 +2802,10 @@ int i40e_ndo_set_vf_port_vlan(struct net_device *netdev, int vf_id,
/* duplicate request, so just return success */
goto error_pvid;
+ /* Locked once because multiple functions below iterate list */
spin_lock_bh(&vsi->mac_filter_hash_lock);
- is_vsi_in_vlan = i40e_is_vsi_in_vlan(vsi);
- spin_unlock_bh(&vsi->mac_filter_hash_lock);
- if (le16_to_cpu(vsi->info.pvid) == 0 && is_vsi_in_vlan) {
+ if (le16_to_cpu(vsi->info.pvid) == 0 && i40e_is_vsi_in_vlan(vsi)) {
dev_err(&pf->pdev->dev,
"VF %d has already configured VLAN filters and the administrator is requesting a port VLAN override.\nPlease unload and reload the VF driver for this change to take effect.\n",
vf_id);
@@ -2830,14 +2828,23 @@ int i40e_ndo_set_vf_port_vlan(struct net_device *netdev, int vf_id,
*/
if ((!(vlan_id || qos) ||
vlanprio != le16_to_cpu(vsi->info.pvid)) &&
- vsi->info.pvid)
- ret = i40e_vsi_add_vlan(vsi, I40E_VLAN_ANY);
+ vsi->info.pvid) {
+ ret = i40e_add_vlan_all_mac(vsi, I40E_VLAN_ANY);
+ if (ret) {
+ dev_info(&vsi->back->pdev->dev,
+ "add VF VLAN failed, ret=%d aq_err=%d\n", ret,
+ vsi->back->hw.aq.asq_last_status);
+ spin_unlock_bh(&vsi->mac_filter_hash_lock);
+ goto error_pvid;
+ }
+ }
if (vsi->info.pvid) {
- /* kill old VLAN */
- i40e_vsi_kill_vlan(vsi, (le16_to_cpu(vsi->info.pvid) &
- VLAN_VID_MASK));
+ /* remove all filters on the old VLAN */
+ i40e_rm_vlan_all_mac(vsi, (le16_to_cpu(vsi->info.pvid) &
+ VLAN_VID_MASK));
}
+
if (vlan_id || qos)
ret = i40e_vsi_add_pvid(vsi, vlanprio);
else
@@ -2847,24 +2854,30 @@ int i40e_ndo_set_vf_port_vlan(struct net_device *netdev, int vf_id,
dev_info(&pf->pdev->dev, "Setting VLAN %d, QOS 0x%x on VF %d\n",
vlan_id, qos, vf_id);
- /* add new VLAN filter */
- ret = i40e_vsi_add_vlan(vsi, vlan_id);
+ /* add new VLAN filter for each MAC */
+ ret = i40e_add_vlan_all_mac(vsi, vlan_id);
if (ret) {
dev_info(&vsi->back->pdev->dev,
"add VF VLAN failed, ret=%d aq_err=%d\n", ret,
vsi->back->hw.aq.asq_last_status);
+ spin_unlock_bh(&vsi->mac_filter_hash_lock);
goto error_pvid;
}
- /* Kill non-vlan MAC filters - ignore error return since
- * there might not be any non-vlan MAC filters.
- */
- i40e_vsi_kill_vlan(vsi, I40E_VLAN_ANY);
+
+ /* remove the previously added non-VLAN MAC filters */
+ i40e_rm_vlan_all_mac(vsi, I40E_VLAN_ANY);
}
+ spin_unlock_bh(&vsi->mac_filter_hash_lock);
+
+ /* Schedule the worker thread to take care of applying changes */
+ i40e_service_event_schedule(vsi->back);
+
if (ret) {
dev_err(&pf->pdev->dev, "Unable to update VF vsi context\n");
goto error_pvid;
}
+
/* The Port VLAN needs to be saved across resets the same as the
* default LAN MAC address.
*/
--
2.9.3
^ permalink raw reply related
* [net-next v2 19/19] i40e: move all updates for VLAN mode into i40e_sync_vsi_filters
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.
The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.
Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.
Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.
The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.
Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.
Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 214 +++++++++++++++-------------
1 file changed, 113 insertions(+), 101 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 49261cc..da4cbe3 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -1227,6 +1227,107 @@ bool i40e_is_vsi_in_vlan(struct i40e_vsi *vsi)
}
/**
+ * i40e_correct_mac_vlan_filters - Correct non-VLAN filters if necessary
+ * @vsi: the VSI to configure
+ * @tmp_add_list: list of filters ready to be added
+ * @tmp_del_list: list of filters ready to be deleted
+ * @vlan_filters: the number of active VLAN filters
+ *
+ * Update VLAN=0 and VLAN=-1 (I40E_VLAN_ANY) filters properly so that they
+ * behave as expected. If we have any active VLAN filters remaining or about
+ * to be added then we need to update non-VLAN filters to be marked as VLAN=0
+ * so that they only match against untagged traffic. If we no longer have any
+ * active VLAN filters, we need to make all non-VLAN filters marked as VLAN=-1
+ * so that they match against both tagged and untagged traffic. In this way,
+ * we ensure that we correctly receive the desired traffic. This ensures that
+ * when we have an active VLAN we will receive only untagged traffic and
+ * traffic matching active VLANs. If we have no active VLANs then we will
+ * operate in non-VLAN mode and receive all traffic, tagged or untagged.
+ *
+ * Finally, in a similar fashion, this function also corrects filters when
+ * there is an active PVID assigned to this VSI.
+ *
+ * In case of memory allocation failure return -ENOMEM. Otherwise, return 0.
+ *
+ * This function is only expected to be called from within
+ * i40e_sync_vsi_filters.
+ *
+ * NOTE: This function expects to be called while under the
+ * mac_filter_hash_lock
+ */
+static int i40e_correct_mac_vlan_filters(struct i40e_vsi *vsi,
+ struct hlist_head *tmp_add_list,
+ struct hlist_head *tmp_del_list,
+ int vlan_filters)
+{
+ struct i40e_mac_filter *f, *add_head;
+ struct hlist_node *h;
+ int bkt, new_vlan;
+
+ /* To determine if a particular filter needs to be replaced we
+ * have the three following conditions:
+ *
+ * a) if we have a PVID assigned, then all filters which are
+ * not marked as VLAN=PVID must be replaced with filters that
+ * are.
+ * b) otherwise, if we have any active VLANS, all filters
+ * which are marked as VLAN=-1 must be replaced with
+ * filters marked as VLAN=0
+ * c) finally, if we do not have any active VLANS, all filters
+ * which are marked as VLAN=0 must be replaced with filters
+ * marked as VLAN=-1
+ */
+
+ /* Update the filters about to be added in place */
+ hlist_for_each_entry(f, tmp_add_list, hlist) {
+ if (vsi->info.pvid && f->vlan != vsi->info.pvid)
+ f->vlan = vsi->info.pvid;
+ else if (vlan_filters && f->vlan == I40E_VLAN_ANY)
+ f->vlan = 0;
+ else if (!vlan_filters && f->vlan == 0)
+ f->vlan = I40E_VLAN_ANY;
+ }
+
+ /* Update the remaining active filters */
+ hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
+ /* Combine the checks for whether a filter needs to be changed
+ * and then determine the new VLAN inside the if block, in
+ * order to avoid duplicating code for adding the new filter
+ * then deleting the old filter.
+ */
+ if ((vsi->info.pvid && f->vlan != vsi->info.pvid) ||
+ (vlan_filters && f->vlan == I40E_VLAN_ANY) ||
+ (!vlan_filters && f->vlan == 0)) {
+ /* Determine the new vlan we will be adding */
+ if (vsi->info.pvid)
+ new_vlan = vsi->info.pvid;
+ else if (vlan_filters)
+ new_vlan = 0;
+ else
+ new_vlan = I40E_VLAN_ANY;
+
+ /* Create the new filter */
+ add_head = i40e_add_filter(vsi, f->macaddr, new_vlan);
+ if (!add_head)
+ return -ENOMEM;
+
+ /* Put the replacement filter into the add list */
+ hash_del(&add_head->hlist);
+ hlist_add_head(&add_head->hlist, tmp_add_list);
+
+ /* Put the original filter into the delete list */
+ f->state = I40E_FILTER_REMOVE;
+ hash_del(&f->hlist);
+ hlist_add_head(&f->hlist, tmp_del_list);
+ }
+ }
+
+ vsi->has_vlan_filter = !!vlan_filters;
+
+ return 0;
+}
+
+/**
* i40e_rm_default_mac_filter - Remove the default MAC filter set by NVM
* @vsi: the PF Main VSI - inappropriate for any other VSI
* @macaddr: the MAC address
@@ -1916,8 +2017,6 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
struct hlist_head tmp_add_list, tmp_del_list;
struct i40e_mac_filter *f, *add_head = NULL;
struct i40e_hw *hw = &vsi->back->hw;
- unsigned int vlan_any_filters = 0;
- unsigned int non_vlan_filters = 0;
unsigned int failed_filters = 0;
unsigned int vlan_filters = 0;
bool promisc_changed = false;
@@ -1974,66 +2073,21 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
hlist_add_head(&f->hlist, &tmp_add_list);
}
- /* Count the number of each type of filter we have
- * remaining, ignoring any filters we're about to
- * delete.
+ /* Count the number of active (current and new) VLAN
+ * filters we have now. Does not count filters which
+ * are marked for deletion.
*/
if (f->vlan > 0)
vlan_filters++;
- else if (!f->vlan)
- non_vlan_filters++;
- else
- vlan_any_filters++;
}
- /* We should never have VLAN=-1 filters at the same time as we
- * have either VLAN=0 or VLAN>0 filters, so warn about this
- * case here to help catch any issues.
- */
- WARN_ON(vlan_any_filters && (vlan_filters + non_vlan_filters));
-
- /* If we only have VLAN=0 filters remaining, and don't have
- * any other VLAN filters, we need to convert these VLAN=0
- * filters into VLAN=-1 (I40E_VLAN_ANY) so that we operate
- * correctly in non-VLAN mode and receive all traffic tagged
- * or untagged.
- */
- if (non_vlan_filters && !vlan_filters) {
- hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f,
- hlist) {
- /* Only replace VLAN=0 filters */
- if (f->vlan)
- continue;
-
- /* Allocate a replacement element */
- add_head = kzalloc(sizeof(*add_head),
- GFP_KERNEL);
- if (!add_head)
- goto err_no_memory_locked;
+ retval = i40e_correct_mac_vlan_filters(vsi,
+ &tmp_add_list,
+ &tmp_del_list,
+ vlan_filters);
+ if (retval)
+ goto err_no_memory_locked;
- /* Copy the filter, with new state and VLAN */
- *add_head = *f;
- add_head->state = I40E_FILTER_NEW;
- add_head->vlan = I40E_VLAN_ANY;
-
- /* Move the replacement to the add list */
- INIT_HLIST_NODE(&add_head->hlist);
- hlist_add_head(&add_head->hlist,
- &tmp_add_list);
-
- /* Move the original to the delete list */
- f->state = I40E_FILTER_REMOVE;
- hash_del(&f->hlist);
- hlist_add_head(&f->hlist, &tmp_del_list);
- }
-
- /* Also update any filters on the tmp_add list */
- hlist_for_each_entry(f, &tmp_add_list, hlist) {
- if (!f->vlan)
- f->vlan = I40E_VLAN_ANY;
- }
- add_head = NULL;
- }
spin_unlock_bh(&vsi->mac_filter_hash_lock);
}
@@ -2098,14 +2152,6 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
del_list = NULL;
}
- /* After finishing notifying firmware of the deleted filters, update
- * the cached value of vsi->has_vlan_filter. Note that we are safe to
- * use just !!vlan_filters here because if we only have VLAN=0 (that
- * is, non_vlan_filters) these will all be converted to VLAN=-1 in the
- * logic above already so this value would still be correct.
- */
- vsi->has_vlan_filter = !!vlan_filters;
-
if (!hlist_empty(&tmp_add_list)) {
/* Do all the adds now. */
filter_list_len = hw->aq.asq_buf_size /
@@ -2533,48 +2579,14 @@ int i40e_add_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
**/
int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
{
- struct i40e_mac_filter *f, *add_f, *del_f;
- struct hlist_node *h;
- int bkt, err;
+ int err;
/* Locked once because all functions invoked below iterates list*/
spin_lock_bh(&vsi->mac_filter_hash_lock);
-
err = i40e_add_vlan_all_mac(vsi, vid);
- if (err) {
- spin_unlock_bh(&vsi->mac_filter_hash_lock);
- return err;
- }
-
- /* When we add a new VLAN filter, we need to make sure that all existing
- * filters which are marked as vid=-1 (I40E_VLAN_ANY) are converted to
- * vid=0. The simplest way is just search for all filters marked as
- * vid=-1 and replace them with vid=0. This converts all filters that
- * were marked to receive all traffic (tagged or untagged) into
- * filters to receive only untagged traffic, so that we don't receive
- * tagged traffic for VLANs which we have not configured.
- */
- if (vid > 0 && !vsi->info.pvid) {
- hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
- if (f->state == I40E_FILTER_REMOVE)
- continue;
- del_f = i40e_find_filter(vsi, f->macaddr,
- I40E_VLAN_ANY);
- if (!del_f)
- continue;
- add_f = i40e_add_filter(vsi, f->macaddr, 0);
- if (!add_f) {
- dev_info(&vsi->back->pdev->dev,
- "Could not add filter 0 for %pM\n",
- f->macaddr);
- spin_unlock_bh(&vsi->mac_filter_hash_lock);
- return -ENOMEM;
- }
- __i40e_del_filter(vsi, del_f);
- }
- }
-
spin_unlock_bh(&vsi->mac_filter_hash_lock);
+ if (err)
+ return err;
/* schedule our worker thread which will take care of
* applying the new filter changes
--
2.9.3
^ permalink raw reply related
* [net-next v2 15/19] i40e: refactor i40e_update_filter_state to avoid passing aq_err
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.
Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.
This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.
The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.
Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 58 +++++++++++------------------
1 file changed, 21 insertions(+), 37 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 2ccf376..8e65972 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -1757,7 +1757,6 @@ static void i40e_undo_filter_entries(struct i40e_vsi *vsi,
* @count: Number of filters added
* @add_list: return data from fw
* @head: pointer to first filter in current batch
- * @aq_err: status from fw
*
* MAC filter entries from list were slated to be added to device. Returns
* number of successful filters. Note that 0 does NOT mean success!
@@ -1765,47 +1764,30 @@ static void i40e_undo_filter_entries(struct i40e_vsi *vsi,
static int
i40e_update_filter_state(int count,
struct i40e_aqc_add_macvlan_element_data *add_list,
- struct i40e_mac_filter *add_head, int aq_err)
+ struct i40e_mac_filter *add_head)
{
int retval = 0;
int i;
-
- if (!aq_err) {
- retval = count;
- /* Everything's good, mark all filters active. */
- for (i = 0; i < count ; i++) {
- add_head->state = I40E_FILTER_ACTIVE;
- add_head = hlist_entry(add_head->hlist.next,
- typeof(struct i40e_mac_filter),
- hlist);
- }
- } else if (aq_err == I40E_AQ_RC_ENOSPC) {
- /* Device ran out of filter space. Check the return value
- * for each filter to see which ones are active.
+ for (i = 0; i < count; i++) {
+ /* Always check status of each filter. We don't need to check
+ * the firmware return status because we pre-set the filter
+ * status to I40E_AQC_MM_ERR_NO_RES when sending the filter
+ * request to the adminq. Thus, if it no longer matches then
+ * we know the filter is active.
*/
- for (i = 0; i < count ; i++) {
- if (add_list[i].match_method ==
- I40E_AQC_MM_ERR_NO_RES) {
- add_head->state = I40E_FILTER_FAILED;
- } else {
- add_head->state = I40E_FILTER_ACTIVE;
- retval++;
- }
- add_head = hlist_entry(add_head->hlist.next,
- typeof(struct i40e_mac_filter),
- hlist);
- }
- } else {
- /* Some other horrible thing happened, fail all filters */
- retval = 0;
- for (i = 0; i < count ; i++) {
+ if (add_list[i].match_method == I40E_AQC_MM_ERR_NO_RES) {
add_head->state = I40E_FILTER_FAILED;
- add_head = hlist_entry(add_head->hlist.next,
- typeof(struct i40e_mac_filter),
- hlist);
+ } else {
+ add_head->state = I40E_FILTER_ACTIVE;
+ retval++;
}
+
+ add_head = hlist_entry(add_head->hlist.next,
+ typeof(struct i40e_mac_filter),
+ hlist);
}
+
return retval;
}
@@ -1864,12 +1846,11 @@ void i40e_aqc_add_filters(struct i40e_vsi *vsi, const char *vsi_name,
int num_add, bool *promisc_changed)
{
struct i40e_hw *hw = &vsi->back->hw;
- i40e_status aq_ret;
int aq_err, fcnt;
- aq_ret = i40e_aq_add_macvlan(hw, vsi->seid, list, num_add, NULL);
+ i40e_aq_add_macvlan(hw, vsi->seid, list, num_add, NULL);
aq_err = hw->aq.asq_last_status;
- fcnt = i40e_update_filter_state(num_add, list, add_head, aq_ret);
+ fcnt = i40e_update_filter_state(num_add, list, add_head);
if (fcnt != num_add) {
*promisc_changed = true;
@@ -2168,6 +2149,9 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
cpu_to_le16((u16)(f->vlan));
}
add_list[num_add].queue_number = 0;
+ /* set invalid match method for later detection */
+ add_list[num_add].match_method =
+ cpu_to_le16((u16)I40E_AQC_MM_ERR_NO_RES);
cmd_flags |= I40E_AQC_MACVLAN_ADD_PERFECT_MATCH;
add_list[num_add].flags = cpu_to_le16(cmd_flags);
num_add++;
--
2.9.3
^ permalink raw reply related
* [net-next v2 14/19] i40e: recalculate vsi->active_filters from hash contents
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
Previous code refactors have accidentally caused issues with the
counting of active_filters. Avoid similar issues in the future by simply
re-counting the active filters every time after we handle add and delete
of all the filters. Additionally this allows us to simplify the check
for when we exit promiscuous mode since we can combine the check for
failed filters at the same time.
Additionally since we recount filters at the end we need to set
vsi->promisc_threshold as well.
The resulting code takes a bit longer since we do have to loop over
filters again. However, the result is more readable and less likely to
become incorrect due to failed accounting of filters in the future.
Finally, this ensures that it is not possible for vsi->active_filters to
ever underflow since we never decrement it.
Change-ID: Ib4f3a377e60eb1fa6c91ea86cc02238c08edd102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 52 ++++++++++++++++-------------
1 file changed, 29 insertions(+), 23 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 806fd56..2ccf376 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -1870,12 +1870,10 @@ void i40e_aqc_add_filters(struct i40e_vsi *vsi, const char *vsi_name,
aq_ret = i40e_aq_add_macvlan(hw, vsi->seid, list, num_add, NULL);
aq_err = hw->aq.asq_last_status;
fcnt = i40e_update_filter_state(num_add, list, add_head, aq_ret);
- vsi->active_filters += fcnt;
if (fcnt != num_add) {
*promisc_changed = true;
set_bit(__I40E_FILTER_OVERFLOW_PROMISC, &vsi->state);
- vsi->promisc_threshold = (vsi->active_filters * 3) / 4;
dev_warn(&vsi->back->pdev->dev,
"Error %s adding RX filters on %s, promiscuous mode forced on\n",
i40e_aq_str(hw, aq_err),
@@ -1939,6 +1937,7 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
struct i40e_hw *hw = &vsi->back->hw;
unsigned int vlan_any_filters = 0;
unsigned int non_vlan_filters = 0;
+ unsigned int failed_filters = 0;
unsigned int vlan_filters = 0;
bool promisc_changed = false;
char vsi_name[16] = "PF";
@@ -1985,7 +1984,6 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
/* Move the element into temporary del_list */
hash_del(&f->hlist);
hlist_add_head(&f->hlist, &tmp_del_list);
- vsi->active_filters--;
/* Avoid counting removed filters */
continue;
@@ -2046,7 +2044,6 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
f->state = I40E_FILTER_REMOVE;
hash_del(&f->hlist);
hlist_add_head(&f->hlist, &tmp_del_list);
- vsi->active_filters--;
}
/* Also update any filters on the tmp_add list */
@@ -2203,27 +2200,36 @@ int i40e_sync_vsi_filters(struct i40e_vsi *vsi)
add_list = NULL;
}
- /* Check to see if we can drop out of overflow promiscuous mode. */
+ /* Determine the number of active and failed filters. */
+ spin_lock_bh(&vsi->mac_filter_hash_lock);
+ vsi->active_filters = 0;
+ hash_for_each(vsi->mac_filter_hash, bkt, f, hlist) {
+ if (f->state == I40E_FILTER_ACTIVE)
+ vsi->active_filters++;
+ else if (f->state == I40E_FILTER_FAILED)
+ failed_filters++;
+ }
+ spin_unlock_bh(&vsi->mac_filter_hash_lock);
+
+ /* If promiscuous mode has changed, we need to calculate a new
+ * threshold for when we are safe to exit
+ */
+ if (promisc_changed)
+ vsi->promisc_threshold = (vsi->active_filters * 3) / 4;
+
+ /* Check if we are able to exit overflow promiscuous mode. We can
+ * safely exit if we didn't just enter, we no longer have any failed
+ * filters, and we have reduced filters below the threshold value.
+ */
if (test_bit(__I40E_FILTER_OVERFLOW_PROMISC, &vsi->state) &&
+ !promisc_changed && !failed_filters &&
(vsi->active_filters < vsi->promisc_threshold)) {
- int failed_count = 0;
- /* See if we have any failed filters. We can't drop out of
- * promiscuous until these have all been deleted.
- */
- spin_lock_bh(&vsi->mac_filter_hash_lock);
- hash_for_each(vsi->mac_filter_hash, bkt, f, hlist) {
- if (f->state == I40E_FILTER_FAILED)
- failed_count++;
- }
- spin_unlock_bh(&vsi->mac_filter_hash_lock);
- if (!failed_count) {
- dev_info(&pf->pdev->dev,
- "filter logjam cleared on %s, leaving overflow promiscuous mode\n",
- vsi_name);
- clear_bit(__I40E_FILTER_OVERFLOW_PROMISC, &vsi->state);
- promisc_changed = true;
- vsi->promisc_threshold = 0;
- }
+ dev_info(&pf->pdev->dev,
+ "filter logjam cleared on %s, leaving overflow promiscuous mode\n",
+ vsi_name);
+ clear_bit(__I40E_FILTER_OVERFLOW_PROMISC, &vsi->state);
+ promisc_changed = true;
+ vsi->promisc_threshold = 0;
}
/* if the VF is not trusted do not do promisc */
--
2.9.3
^ permalink raw reply related
* [net-next v2 17/19] i40e: factor out addition/deletion of VLAN per each MAC address
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.
Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.
Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 68 +++++++++++++++++++++++------
1 file changed, 55 insertions(+), 13 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index f9e9c90..8aedfb7 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -2493,19 +2493,24 @@ static void i40e_vlan_rx_register(struct net_device *netdev, u32 features)
}
/**
- * i40e_vsi_add_vlan - Add vsi membership for given vlan
+ * i40e_add_vlan_all_mac - Add a MAC/VLAN filter for each existing MAC address
* @vsi: the vsi being configured
* @vid: vlan id to be added (0 = untagged only , -1 = any)
+ *
+ * This is a helper function for adding a new MAC/VLAN filter with the
+ * specified VLAN for each existing MAC address already in the hash table.
+ * This function does *not* perform any accounting to update filters based on
+ * VLAN mode.
+ *
+ * NOTE: this function expects to be called while under the
+ * mac_filter_hash_lock
**/
-int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
+static int i40e_add_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
{
- struct i40e_mac_filter *f, *add_f, *del_f;
+ struct i40e_mac_filter *f, *add_f;
struct hlist_node *h;
int bkt;
- /* Locked once because all functions invoked below iterates list*/
- spin_lock_bh(&vsi->mac_filter_hash_lock);
-
hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
if (f->state == I40E_FILTER_REMOVE)
continue;
@@ -2514,11 +2519,33 @@ int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
dev_info(&vsi->back->pdev->dev,
"Could not add vlan filter %d for %pM\n",
vid, f->macaddr);
- spin_unlock_bh(&vsi->mac_filter_hash_lock);
return -ENOMEM;
}
}
+ return 0;
+}
+
+/**
+ * i40e_vsi_add_vlan - Add VSI membership for given VLAN
+ * @vsi: the VSI being configured
+ * @vid: VLAN id to be added (0 = untagged only , -1 = any)
+ **/
+int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
+{
+ struct i40e_mac_filter *f, *add_f, *del_f;
+ struct hlist_node *h;
+ int bkt, err;
+
+ /* Locked once because all functions invoked below iterates list*/
+ spin_lock_bh(&vsi->mac_filter_hash_lock);
+
+ err = i40e_add_vlan_all_mac(vsi, vid);
+ if (err) {
+ spin_unlock_bh(&vsi->mac_filter_hash_lock);
+ return err;
+ }
+
/* When we add a new VLAN filter, we need to make sure that all existing
* filters which are marked as vid=-1 (I40E_VLAN_ANY) are converted to
* vid=0. The simplest way is just search for all filters marked as
@@ -2557,24 +2584,39 @@ int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
}
/**
- * i40e_vsi_kill_vlan - Remove vsi membership for given vlan
+ * i40e_rm_vlan_all_mac - Remove MAC/VLAN pair for all MAC with the given VLAN
* @vsi: the vsi being configured
* @vid: vlan id to be removed (0 = untagged only , -1 = any)
- **/
-void i40e_vsi_kill_vlan(struct i40e_vsi *vsi, s16 vid)
+ *
+ * This function should be used to remove all VLAN filters which match the
+ * given VID. It does not schedule the service event and does not take the
+ * mac_filter_hash_lock so it may be combined with other operations under
+ * a single invocation of the mac_filter_hash_lock.
+ *
+ * NOTE: this function expects to be called while under the
+ * mac_filter_hash_lock
+ */
+static void i40e_rm_vlan_all_mac(struct i40e_vsi *vsi, s16 vid)
{
struct i40e_mac_filter *f;
struct hlist_node *h;
int bkt;
- /* Locked once because all functions invoked below iterates list */
- spin_lock_bh(&vsi->mac_filter_hash_lock);
-
hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
if (f->vlan == vid)
__i40e_del_filter(vsi, f);
}
+}
+/**
+ * i40e_vsi_kill_vlan - Remove VSI membership for given VLAN
+ * @vsi: the VSI being configured
+ * @vid: VLAN id to be removed (0 = untagged only , -1 = any)
+ **/
+void i40e_vsi_kill_vlan(struct i40e_vsi *vsi, s16 vid)
+{
+ spin_lock_bh(&vsi->mac_filter_hash_lock);
+ i40e_rm_vlan_all_mac(vsi, vid);
spin_unlock_bh(&vsi->mac_filter_hash_lock);
/* schedule our worker thread which will take care of
--
2.9.3
^ permalink raw reply related
* [net-next v2 13/19] i40e: defeature support for PTP L4 frame detection on XL710
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e.h | 1 +
drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 15 +++++++++++++--
drivers/net/ethernet/intel/i40e/i40e_main.c | 3 ++-
drivers/net/ethernet/intel/i40e/i40e_ptp.c | 21 +++++++++++++++------
4 files changed, 31 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index b8f2978..f1d838f 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -360,6 +360,7 @@ struct i40e_pf {
#define I40E_FLAG_PF_MAC BIT_ULL(50)
#define I40E_FLAG_TRUE_PROMISC_SUPPORT BIT_ULL(51)
#define I40E_FLAG_HAVE_CRT_RETIMER BIT_ULL(52)
+#define I40E_FLAG_PTP_L4_CAPABLE BIT_ULL(53)
/* tracks features that get auto disabled by errors */
u64 auto_disable_flags;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index 935160a..cc1465a 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -1681,8 +1681,19 @@ static int i40e_get_ts_info(struct net_device *dev,
info->tx_types = BIT(HWTSTAMP_TX_OFF) | BIT(HWTSTAMP_TX_ON);
info->rx_filters = BIT(HWTSTAMP_FILTER_NONE) |
- BIT(HWTSTAMP_FILTER_PTP_V1_L4_EVENT) |
- BIT(HWTSTAMP_FILTER_PTP_V2_EVENT);
+ BIT(HWTSTAMP_FILTER_PTP_V2_L2_EVENT) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ);
+
+ if (pf->flags & I40E_FLAG_PTP_L4_CAPABLE)
+ info->rx_filters |= BIT(HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
+ BIT(HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_EVENT) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_L4_EVENT) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_SYNC) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_DELAY_REQ) |
+ BIT(HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ);
return 0;
}
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index c47e9c5..806fd56 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -8699,7 +8699,8 @@ static int i40e_sw_init(struct i40e_pf *pf)
I40E_FLAG_MULTIPLE_TCP_UDP_RSS_PCTYPE |
I40E_FLAG_NO_PCI_LINK_CHECK |
I40E_FLAG_USE_SET_LLDP_MIB |
- I40E_FLAG_GENEVE_OFFLOAD_CAPABLE;
+ I40E_FLAG_GENEVE_OFFLOAD_CAPABLE |
+ I40E_FLAG_PTP_L4_CAPABLE;
} else if ((pf->hw.aq.api_maj_ver > 1) ||
((pf->hw.aq.api_maj_ver == 1) &&
(pf->hw.aq.api_min_ver > 4))) {
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ptp.c b/drivers/net/ethernet/intel/i40e/i40e_ptp.c
index 5e2272c..9e49ffa 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ptp.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ptp.c
@@ -521,6 +521,8 @@ static int i40e_ptp_set_timestamp_mode(struct i40e_pf *pf,
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+ if (!(pf->flags & I40E_FLAG_PTP_L4_CAPABLE))
+ return -ERANGE;
pf->ptp_rx = true;
tsyntype = I40E_PRTTSYN_CTL1_V1MESSTYPE0_MASK |
I40E_PRTTSYN_CTL1_TSYNTYPE_V1 |
@@ -528,19 +530,26 @@ static int i40e_ptp_set_timestamp_mode(struct i40e_pf *pf,
config->rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
break;
case HWTSTAMP_FILTER_PTP_V2_EVENT:
- case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
case HWTSTAMP_FILTER_PTP_V2_SYNC:
- case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
- case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+ if (!(pf->flags & I40E_FLAG_PTP_L4_CAPABLE))
+ return -ERANGE;
+ /* fall through */
+ case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
pf->ptp_rx = true;
tsyntype = I40E_PRTTSYN_CTL1_V2MESSTYPE0_MASK |
- I40E_PRTTSYN_CTL1_TSYNTYPE_V2 |
- I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
- config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+ I40E_PRTTSYN_CTL1_TSYNTYPE_V2;
+ if (pf->flags & I40E_FLAG_PTP_L4_CAPABLE) {
+ tsyntype |= I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
+ config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+ } else {
+ config->rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+ }
break;
case HWTSTAMP_FILTER_ALL:
default:
--
2.9.3
^ permalink raw reply related
* [net-next v2 16/19] i40e: delete filter after adding its replacement when converting
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Jacob Keller, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.
Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 8e65972..f9e9c90 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -2535,7 +2535,6 @@ int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
I40E_VLAN_ANY);
if (!del_f)
continue;
- __i40e_del_filter(vsi, del_f);
add_f = i40e_add_filter(vsi, f->macaddr, 0);
if (!add_f) {
dev_info(&vsi->back->pdev->dev,
@@ -2544,6 +2543,7 @@ int i40e_vsi_add_vlan(struct i40e_vsi *vsi, s16 vid)
spin_unlock_bh(&vsi->mac_filter_hash_lock);
return -ENOMEM;
}
+ __i40e_del_filter(vsi, del_f);
}
}
--
2.9.3
^ permalink raw reply related
* [net-next v2 10/19] i40e: Add FEC for 25g
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Carolyn Wyborny, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Mitch Williams, Jacek Naczyk, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Carolyn Wyborny <carolyn.wyborny@intel.com>
This patch adds adminq support for Forward Error
Correction ("FEC")for 25g products.
Change-ID: Iaff4910737c239d2c730e5c22a313ce9c37d3964
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h | 25 ++++++++++++++++++++--
drivers/net/ethernet/intel/i40e/i40e_common.c | 2 ++
.../net/ethernet/intel/i40evf/i40e_adminq_cmd.h | 25 ++++++++++++++++++++--
3 files changed, 48 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h b/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
index c9d1f91..b2101a5 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
@@ -1686,6 +1686,8 @@ struct i40e_aq_get_phy_abilities_resp {
#define I40E_AQ_PHY_LINK_ENABLED 0x08
#define I40E_AQ_PHY_AN_ENABLED 0x10
#define I40E_AQ_PHY_FLAG_MODULE_QUAL 0x20
+#define I40E_AQ_PHY_FEC_ABILITY_KR 0x40
+#define I40E_AQ_PHY_FEC_ABILITY_RS 0x80
__le16 eee_capability;
#define I40E_AQ_EEE_100BASE_TX 0x0002
#define I40E_AQ_EEE_1000BASE_T 0x0004
@@ -1701,7 +1703,16 @@ struct i40e_aq_get_phy_abilities_resp {
#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
- u8 mod_type_ext;
+ u8 fec_cfg_curr_mod_ext_info;
+#define I40E_AQ_ENABLE_FEC_KR 0x01
+#define I40E_AQ_ENABLE_FEC_RS 0x02
+#define I40E_AQ_REQUEST_FEC_KR 0x04
+#define I40E_AQ_REQUEST_FEC_RS 0x08
+#define I40E_AQ_ENABLE_FEC_AUTO 0x10
+#define I40E_AQ_FEC
+#define I40E_AQ_MODULE_TYPE_EXT_MASK 0xE0
+#define I40E_AQ_MODULE_TYPE_EXT_SHIFT 5
+
u8 ext_comp_code;
u8 phy_id[4];
u8 module_type[3];
@@ -1729,7 +1740,15 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
- u8 reserved[2];
+ u8 fec_config;
+#define I40E_AQ_SET_FEC_ABILITY_KR BIT(0)
+#define I40E_AQ_SET_FEC_ABILITY_RS BIT(1)
+#define I40E_AQ_SET_FEC_REQUEST_KR BIT(2)
+#define I40E_AQ_SET_FEC_REQUEST_RS BIT(3)
+#define I40E_AQ_SET_FEC_AUTO BIT(4)
+#define I40E_AQ_PHY_FEC_CONFIG_SHIFT 0x0
+#define I40E_AQ_PHY_FEC_CONFIG_MASK (0x1F << I40E_AQ_PHY_FEC_CONFIG_SHIFT)
+ u8 reserved;
};
I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1819,6 +1838,8 @@ struct i40e_aqc_get_link_status {
u8 loopback; /* use defines from i40e_aqc_set_lb_mode */
__le16 max_frame_size;
u8 config;
+#define I40E_AQ_CONFIG_FEC_KR_ENA 0x01
+#define I40E_AQ_CONFIG_FEC_RS_ENA 0x02
#define I40E_AQ_CONFIG_CRC_ENA 0x04
#define I40E_AQ_CONFIG_PACING_MASK 0x78
u8 external_power_ability;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_common.c b/drivers/net/ethernet/intel/i40e/i40e_common.c
index 1318c7d..f8c4c14 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_common.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_common.c
@@ -1714,6 +1714,8 @@ enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
config.eee_capability = abilities.eee_capability;
config.eeer = abilities.eeer_val;
config.low_power_ctrl = abilities.d3_lpan;
+ config.fec_config = abilities.fec_cfg_curr_mod_ext_info &
+ I40E_AQ_PHY_FEC_CONFIG_MASK;
status = i40e_aq_set_phy_config(hw, &config, NULL);
if (status)
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h b/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
index f8d7d95..eeb9864 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
@@ -1683,6 +1683,8 @@ struct i40e_aq_get_phy_abilities_resp {
#define I40E_AQ_PHY_LINK_ENABLED 0x08
#define I40E_AQ_PHY_AN_ENABLED 0x10
#define I40E_AQ_PHY_FLAG_MODULE_QUAL 0x20
+#define I40E_AQ_PHY_FEC_ABILITY_KR 0x40
+#define I40E_AQ_PHY_FEC_ABILITY_RS 0x80
__le16 eee_capability;
#define I40E_AQ_EEE_100BASE_TX 0x0002
#define I40E_AQ_EEE_1000BASE_T 0x0004
@@ -1698,7 +1700,16 @@ struct i40e_aq_get_phy_abilities_resp {
#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
- u8 mod_type_ext;
+ u8 fec_cfg_curr_mod_ext_info;
+#define I40E_AQ_ENABLE_FEC_KR 0x01
+#define I40E_AQ_ENABLE_FEC_RS 0x02
+#define I40E_AQ_REQUEST_FEC_KR 0x04
+#define I40E_AQ_REQUEST_FEC_RS 0x08
+#define I40E_AQ_ENABLE_FEC_AUTO 0x10
+#define I40E_AQ_FEC
+#define I40E_AQ_MODULE_TYPE_EXT_MASK 0xE0
+#define I40E_AQ_MODULE_TYPE_EXT_SHIFT 5
+
u8 ext_comp_code;
u8 phy_id[4];
u8 module_type[3];
@@ -1726,7 +1737,15 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
- u8 reserved[2];
+ u8 fec_config;
+#define I40E_AQ_SET_FEC_ABILITY_KR BIT(0)
+#define I40E_AQ_SET_FEC_ABILITY_RS BIT(1)
+#define I40E_AQ_SET_FEC_REQUEST_KR BIT(2)
+#define I40E_AQ_SET_FEC_REQUEST_RS BIT(3)
+#define I40E_AQ_SET_FEC_AUTO BIT(4)
+#define I40E_AQ_PHY_FEC_CONFIG_SHIFT 0x0
+#define I40E_AQ_PHY_FEC_CONFIG_MASK (0x1F << I40E_AQ_PHY_FEC_CONFIG_SHIFT)
+ u8 reserved;
};
I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1816,6 +1835,8 @@ struct i40e_aqc_get_link_status {
u8 loopback; /* use defines from i40e_aqc_set_lb_mode */
__le16 max_frame_size;
u8 config;
+#define I40E_AQ_CONFIG_FEC_KR_ENA 0x01
+#define I40E_AQ_CONFIG_FEC_RS_ENA 0x02
#define I40E_AQ_CONFIG_CRC_ENA 0x04
#define I40E_AQ_CONFIG_PACING_MASK 0x78
u8 external_power_ability;
--
2.9.3
^ permalink raw reply related
* [net-next v2 09/19] i40e: Add support for 25G devices
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Carolyn Wyborny, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Mitch Williams, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Carolyn Wyborny <carolyn.wyborny@intel.com>
Add support for 25G devices - defines and data structures.
One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.
This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.
Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h | 30 +++++++-
drivers/net/ethernet/intel/i40e/i40e_common.c | 11 ++-
drivers/net/ethernet/intel/i40e/i40e_devids.h | 2 +
drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 26 ++++++-
drivers/net/ethernet/intel/i40e/i40e_main.c | 6 +-
drivers/net/ethernet/intel/i40e/i40e_type.h | 82 +++++++++++++---------
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c | 3 +
.../net/ethernet/intel/i40evf/i40e_adminq_cmd.h | 30 +++++++-
drivers/net/ethernet/intel/i40evf/i40e_common.c | 2 +
drivers/net/ethernet/intel/i40evf/i40e_devids.h | 2 +
drivers/net/ethernet/intel/i40evf/i40e_type.h | 82 +++++++++++++---------
drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c | 8 +++
.../net/ethernet/intel/i40evf/i40evf_virtchnl.c | 3 +
13 files changed, 208 insertions(+), 79 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h b/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
index 67e396b..c9d1f91 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h
@@ -1642,6 +1642,10 @@ enum i40e_aq_phy_type {
I40E_PHY_TYPE_1000BASE_LX = 0x1C,
I40E_PHY_TYPE_1000BASE_T_OPTICAL = 0x1D,
I40E_PHY_TYPE_20GBASE_KR2 = 0x1E,
+ I40E_PHY_TYPE_25GBASE_KR = 0x1F,
+ I40E_PHY_TYPE_25GBASE_CR = 0x20,
+ I40E_PHY_TYPE_25GBASE_SR = 0x21,
+ I40E_PHY_TYPE_25GBASE_LR = 0x22,
I40E_PHY_TYPE_MAX
};
@@ -1650,6 +1654,7 @@ enum i40e_aq_phy_type {
#define I40E_LINK_SPEED_10GB_SHIFT 0x3
#define I40E_LINK_SPEED_40GB_SHIFT 0x4
#define I40E_LINK_SPEED_20GB_SHIFT 0x5
+#define I40E_LINK_SPEED_25GB_SHIFT 0x6
enum i40e_aq_link_speed {
I40E_LINK_SPEED_UNKNOWN = 0,
@@ -1657,7 +1662,8 @@ enum i40e_aq_link_speed {
I40E_LINK_SPEED_1GB = BIT(I40E_LINK_SPEED_1000MB_SHIFT),
I40E_LINK_SPEED_10GB = BIT(I40E_LINK_SPEED_10GB_SHIFT),
I40E_LINK_SPEED_40GB = BIT(I40E_LINK_SPEED_40GB_SHIFT),
- I40E_LINK_SPEED_20GB = BIT(I40E_LINK_SPEED_20GB_SHIFT)
+ I40E_LINK_SPEED_20GB = BIT(I40E_LINK_SPEED_20GB_SHIFT),
+ I40E_LINK_SPEED_25GB = BIT(I40E_LINK_SPEED_25GB_SHIFT),
};
struct i40e_aqc_module_desc {
@@ -1690,7 +1696,13 @@ struct i40e_aq_get_phy_abilities_resp {
__le32 eeer_val;
u8 d3_lpan;
#define I40E_AQ_SET_PHY_D3_LPAN_ENA 0x01
- u8 reserved[3];
+ u8 phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR 0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
+ u8 mod_type_ext;
+ u8 ext_comp_code;
u8 phy_id[4];
u8 module_type[3];
u8 qualified_module_count;
@@ -1712,7 +1724,12 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
__le16 eee_capability;
__le32 eeer;
u8 low_power_ctrl;
- u8 reserved[3];
+ u8 phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR 0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
+ u8 reserved[2];
};
I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1792,6 +1809,13 @@ struct i40e_aqc_get_link_status {
#define I40E_AQ_LINK_TX_DRAINED 0x01
#define I40E_AQ_LINK_TX_FLUSHED 0x03
#define I40E_AQ_LINK_FORCED_40G 0x10
+/* 25G Error Codes */
+#define I40E_AQ_25G_NO_ERR 0X00
+#define I40E_AQ_25G_NOT_PRESENT 0X01
+#define I40E_AQ_25G_NVM_CRC_ERR 0X02
+#define I40E_AQ_25G_SBUS_UCODE_ERR 0X03
+#define I40E_AQ_25G_SERDES_UCODE_ERR 0X04
+#define I40E_AQ_25G_NIMB_UCODE_ERR 0X05
u8 loopback; /* use defines from i40e_aqc_set_lb_mode */
__le16 max_frame_size;
u8 config;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_common.c b/drivers/net/ethernet/intel/i40e/i40e_common.c
index eb392d6..1318c7d 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_common.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_common.c
@@ -53,6 +53,8 @@ static i40e_status i40e_set_mac_type(struct i40e_hw *hw)
case I40E_DEV_ID_10G_BASE_T4:
case I40E_DEV_ID_20G_KR2:
case I40E_DEV_ID_20G_KR2_A:
+ case I40E_DEV_ID_25G_B:
+ case I40E_DEV_ID_25G_SFP28:
hw->mac.type = I40E_MAC_XL710;
break;
case I40E_DEV_ID_KX_X722:
@@ -1183,6 +1185,8 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
case I40E_PHY_TYPE_1000BASE_LX:
case I40E_PHY_TYPE_40GBASE_SR4:
case I40E_PHY_TYPE_40GBASE_LR4:
+ case I40E_PHY_TYPE_25GBASE_LR:
+ case I40E_PHY_TYPE_25GBASE_SR:
media = I40E_MEDIA_TYPE_FIBER;
break;
case I40E_PHY_TYPE_100BASE_TX:
@@ -1197,6 +1201,7 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
case I40E_PHY_TYPE_10GBASE_SFPP_CU:
case I40E_PHY_TYPE_40GBASE_AOC:
case I40E_PHY_TYPE_10GBASE_AOC:
+ case I40E_PHY_TYPE_25GBASE_CR:
media = I40E_MEDIA_TYPE_DA;
break;
case I40E_PHY_TYPE_1000BASE_KX:
@@ -1204,6 +1209,7 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
case I40E_PHY_TYPE_10GBASE_KR:
case I40E_PHY_TYPE_40GBASE_KR4:
case I40E_PHY_TYPE_20GBASE_KR2:
+ case I40E_PHY_TYPE_25GBASE_KR:
media = I40E_MEDIA_TYPE_BACKPLANE;
break;
case I40E_PHY_TYPE_SGMII:
@@ -1608,8 +1614,10 @@ i40e_status i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
if (hw->aq.asq_last_status == I40E_AQ_RC_EIO)
status = I40E_ERR_UNKNOWN_PHY;
- if (report_init)
+ if (report_init) {
hw->phy.phy_types = le32_to_cpu(abilities->phy_type);
+ hw->phy.phy_types |= ((u64)abilities->phy_type_ext << 32);
+ }
return status;
}
@@ -1701,6 +1709,7 @@ enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
config.abilities |= I40E_AQ_PHY_ENABLE_ATOMIC_LINK;
/* Copy over all the old settings */
config.phy_type = abilities.phy_type;
+ config.phy_type_ext = abilities.phy_type_ext;
config.link_speed = abilities.link_speed;
config.eee_capability = abilities.eee_capability;
config.eeer = abilities.eeer_val;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_devids.h b/drivers/net/ethernet/intel/i40e/i40e_devids.h
index dd4457d..8e46098 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_devids.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_devids.h
@@ -39,6 +39,8 @@
#define I40E_DEV_ID_20G_KR2 0x1587
#define I40E_DEV_ID_20G_KR2_A 0x1588
#define I40E_DEV_ID_10G_BASE_T4 0x1589
+#define I40E_DEV_ID_25G_B 0x158A
+#define I40E_DEV_ID_25G_SFP28 0x158B
#define I40E_DEV_ID_KX_X722 0x37CE
#define I40E_DEV_ID_QSFP_X722 0x37CF
#define I40E_DEV_ID_SFP_X722 0x37D0
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index 6ba0035..935160a 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -265,8 +265,9 @@ static void i40e_partition_setting_complaint(struct i40e_pf *pf)
static void i40e_phy_type_to_ethtool(struct i40e_pf *pf, u32 *supported,
u32 *advertising)
{
- enum i40e_aq_capabilities_phy_type phy_types = pf->hw.phy.phy_types;
struct i40e_link_status *hw_link_info = &pf->hw.phy.link_info;
+ u64 phy_types = pf->hw.phy.phy_types;
+
*supported = 0x0;
*advertising = 0x0;
@@ -369,6 +370,13 @@ static void i40e_phy_type_to_ethtool(struct i40e_pf *pf, u32 *supported,
if (!(pf->flags & I40E_FLAG_HAVE_CRT_RETIMER))
*advertising |= ADVERTISED_1000baseKX_Full;
}
+ if (phy_types & I40E_CAP_PHY_TYPE_25GBASE_KR ||
+ phy_types & I40E_CAP_PHY_TYPE_25GBASE_CR ||
+ phy_types & I40E_CAP_PHY_TYPE_25GBASE_SR ||
+ phy_types & I40E_CAP_PHY_TYPE_25GBASE_LR) {
+ *supported |= SUPPORTED_Autoneg;
+ *advertising |= ADVERTISED_Autoneg;
+ }
}
/**
@@ -491,6 +499,14 @@ static void i40e_get_settings_link_up(struct i40e_hw *hw,
ADVERTISED_1000baseKX_Full |
ADVERTISED_Autoneg;
break;
+ case I40E_PHY_TYPE_25GBASE_KR:
+ case I40E_PHY_TYPE_25GBASE_CR:
+ case I40E_PHY_TYPE_25GBASE_SR:
+ case I40E_PHY_TYPE_25GBASE_LR:
+ ecmd->supported = SUPPORTED_Autoneg;
+ ecmd->advertising = ADVERTISED_Autoneg;
+ /* TODO: add speeds when ethtool is ready to support*/
+ break;
default:
/* if we got here and link is up something bad is afoot */
netdev_info(netdev, "WARNING: Link is up but PHY type 0x%x is not recognized.\n",
@@ -512,6 +528,14 @@ static void i40e_get_settings_link_up(struct i40e_hw *hw,
case I40E_LINK_SPEED_40GB:
ethtool_cmd_speed_set(ecmd, SPEED_40000);
break;
+ case I40E_LINK_SPEED_25GB:
+#ifdef SPEED_25000
+ ethtool_cmd_speed_set(ecmd, SPEED_25000);
+#else
+ netdev_info(netdev,
+ "Speed is 25G, display not supported by this version of ethtool.\n");
+#endif
+ break;
case I40E_LINK_SPEED_20GB:
ethtool_cmd_speed_set(ecmd, SPEED_20000);
break;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index aecf63b..b0486c9 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -86,6 +86,8 @@ static const struct pci_device_id i40e_pci_tbl[] = {
{PCI_VDEVICE(INTEL, I40E_DEV_ID_SFP_I_X722), 0},
{PCI_VDEVICE(INTEL, I40E_DEV_ID_20G_KR2), 0},
{PCI_VDEVICE(INTEL, I40E_DEV_ID_20G_KR2_A), 0},
+ {PCI_VDEVICE(INTEL, I40E_DEV_ID_25G_B), 0},
+ {PCI_VDEVICE(INTEL, I40E_DEV_ID_25G_SFP28), 0},
/* required last entry */
{0, }
};
@@ -5260,6 +5262,9 @@ void i40e_print_link_message(struct i40e_vsi *vsi, bool isup)
case I40E_LINK_SPEED_20GB:
speed = "20 G";
break;
+ case I40E_LINK_SPEED_25GB:
+ speed = "25 G";
+ break;
case I40E_LINK_SPEED_10GB:
speed = "10 G";
break;
@@ -11368,7 +11373,6 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
dev_dbg(&pf->pdev->dev, "get supported phy types ret = %s last_status = %s\n",
i40e_stat_str(&pf->hw, err),
i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
- pf->hw.phy.phy_types = le32_to_cpu(abilities.phy_type);
/* Add a filter to drop all Flow control frames from any VSI from being
* transmitted. By doing so we stop a malicious VF from sending out
diff --git a/drivers/net/ethernet/intel/i40e/i40e_type.h b/drivers/net/ethernet/intel/i40e/i40e_type.h
index bd1ffae..edc0abd 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_type.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_type.h
@@ -213,47 +213,59 @@ struct i40e_link_status {
#define I40E_MODULE_TYPE_1000BASE_T 0x08
};
-enum i40e_aq_capabilities_phy_type {
- I40E_CAP_PHY_TYPE_SGMII = BIT(I40E_PHY_TYPE_SGMII),
- I40E_CAP_PHY_TYPE_1000BASE_KX = BIT(I40E_PHY_TYPE_1000BASE_KX),
- I40E_CAP_PHY_TYPE_10GBASE_KX4 = BIT(I40E_PHY_TYPE_10GBASE_KX4),
- I40E_CAP_PHY_TYPE_10GBASE_KR = BIT(I40E_PHY_TYPE_10GBASE_KR),
- I40E_CAP_PHY_TYPE_40GBASE_KR4 = BIT(I40E_PHY_TYPE_40GBASE_KR4),
- I40E_CAP_PHY_TYPE_XAUI = BIT(I40E_PHY_TYPE_XAUI),
- I40E_CAP_PHY_TYPE_XFI = BIT(I40E_PHY_TYPE_XFI),
- I40E_CAP_PHY_TYPE_SFI = BIT(I40E_PHY_TYPE_SFI),
- I40E_CAP_PHY_TYPE_XLAUI = BIT(I40E_PHY_TYPE_XLAUI),
- I40E_CAP_PHY_TYPE_XLPPI = BIT(I40E_PHY_TYPE_XLPPI),
- I40E_CAP_PHY_TYPE_40GBASE_CR4_CU = BIT(I40E_PHY_TYPE_40GBASE_CR4_CU),
- I40E_CAP_PHY_TYPE_10GBASE_CR1_CU = BIT(I40E_PHY_TYPE_10GBASE_CR1_CU),
- I40E_CAP_PHY_TYPE_10GBASE_AOC = BIT(I40E_PHY_TYPE_10GBASE_AOC),
- I40E_CAP_PHY_TYPE_40GBASE_AOC = BIT(I40E_PHY_TYPE_40GBASE_AOC),
- I40E_CAP_PHY_TYPE_100BASE_TX = BIT(I40E_PHY_TYPE_100BASE_TX),
- I40E_CAP_PHY_TYPE_1000BASE_T = BIT(I40E_PHY_TYPE_1000BASE_T),
- I40E_CAP_PHY_TYPE_10GBASE_T = BIT(I40E_PHY_TYPE_10GBASE_T),
- I40E_CAP_PHY_TYPE_10GBASE_SR = BIT(I40E_PHY_TYPE_10GBASE_SR),
- I40E_CAP_PHY_TYPE_10GBASE_LR = BIT(I40E_PHY_TYPE_10GBASE_LR),
- I40E_CAP_PHY_TYPE_10GBASE_SFPP_CU = BIT(I40E_PHY_TYPE_10GBASE_SFPP_CU),
- I40E_CAP_PHY_TYPE_10GBASE_CR1 = BIT(I40E_PHY_TYPE_10GBASE_CR1),
- I40E_CAP_PHY_TYPE_40GBASE_CR4 = BIT(I40E_PHY_TYPE_40GBASE_CR4),
- I40E_CAP_PHY_TYPE_40GBASE_SR4 = BIT(I40E_PHY_TYPE_40GBASE_SR4),
- I40E_CAP_PHY_TYPE_40GBASE_LR4 = BIT(I40E_PHY_TYPE_40GBASE_LR4),
- I40E_CAP_PHY_TYPE_1000BASE_SX = BIT(I40E_PHY_TYPE_1000BASE_SX),
- I40E_CAP_PHY_TYPE_1000BASE_LX = BIT(I40E_PHY_TYPE_1000BASE_LX),
- I40E_CAP_PHY_TYPE_1000BASE_T_OPTICAL =
- BIT(I40E_PHY_TYPE_1000BASE_T_OPTICAL),
- I40E_CAP_PHY_TYPE_20GBASE_KR2 = BIT(I40E_PHY_TYPE_20GBASE_KR2)
-};
-
struct i40e_phy_info {
struct i40e_link_status link_info;
struct i40e_link_status link_info_old;
bool get_link_info;
enum i40e_media_type media_type;
/* all the phy types the NVM is capable of */
- enum i40e_aq_capabilities_phy_type phy_types;
-};
-
+ u64 phy_types;
+};
+
+#define I40E_CAP_PHY_TYPE_SGMII BIT_ULL(I40E_PHY_TYPE_SGMII)
+#define I40E_CAP_PHY_TYPE_1000BASE_KX BIT_ULL(I40E_PHY_TYPE_1000BASE_KX)
+#define I40E_CAP_PHY_TYPE_10GBASE_KX4 BIT_ULL(I40E_PHY_TYPE_10GBASE_KX4)
+#define I40E_CAP_PHY_TYPE_10GBASE_KR BIT_ULL(I40E_PHY_TYPE_10GBASE_KR)
+#define I40E_CAP_PHY_TYPE_40GBASE_KR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_KR4)
+#define I40E_CAP_PHY_TYPE_XAUI BIT_ULL(I40E_PHY_TYPE_XAUI)
+#define I40E_CAP_PHY_TYPE_XFI BIT_ULL(I40E_PHY_TYPE_XFI)
+#define I40E_CAP_PHY_TYPE_SFI BIT_ULL(I40E_PHY_TYPE_SFI)
+#define I40E_CAP_PHY_TYPE_XLAUI BIT_ULL(I40E_PHY_TYPE_XLAUI)
+#define I40E_CAP_PHY_TYPE_XLPPI BIT_ULL(I40E_PHY_TYPE_XLPPI)
+#define I40E_CAP_PHY_TYPE_40GBASE_CR4_CU BIT_ULL(I40E_PHY_TYPE_40GBASE_CR4_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_CR1_CU BIT_ULL(I40E_PHY_TYPE_10GBASE_CR1_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_AOC BIT_ULL(I40E_PHY_TYPE_10GBASE_AOC)
+#define I40E_CAP_PHY_TYPE_40GBASE_AOC BIT_ULL(I40E_PHY_TYPE_40GBASE_AOC)
+#define I40E_CAP_PHY_TYPE_100BASE_TX BIT_ULL(I40E_PHY_TYPE_100BASE_TX)
+#define I40E_CAP_PHY_TYPE_1000BASE_T BIT_ULL(I40E_PHY_TYPE_1000BASE_T)
+#define I40E_CAP_PHY_TYPE_10GBASE_T BIT_ULL(I40E_PHY_TYPE_10GBASE_T)
+#define I40E_CAP_PHY_TYPE_10GBASE_SR BIT_ULL(I40E_PHY_TYPE_10GBASE_SR)
+#define I40E_CAP_PHY_TYPE_10GBASE_LR BIT_ULL(I40E_PHY_TYPE_10GBASE_LR)
+#define I40E_CAP_PHY_TYPE_10GBASE_SFPP_CU BIT_ULL(I40E_PHY_TYPE_10GBASE_SFPP_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_CR1 BIT_ULL(I40E_PHY_TYPE_10GBASE_CR1)
+#define I40E_CAP_PHY_TYPE_40GBASE_CR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_CR4)
+#define I40E_CAP_PHY_TYPE_40GBASE_SR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_SR4)
+#define I40E_CAP_PHY_TYPE_40GBASE_LR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_LR4)
+#define I40E_CAP_PHY_TYPE_1000BASE_SX BIT_ULL(I40E_PHY_TYPE_1000BASE_SX)
+#define I40E_CAP_PHY_TYPE_1000BASE_LX BIT_ULL(I40E_PHY_TYPE_1000BASE_LX)
+#define I40E_CAP_PHY_TYPE_1000BASE_T_OPTICAL \
+ BIT_ULL(I40E_PHY_TYPE_1000BASE_T_OPTICAL)
+#define I40E_CAP_PHY_TYPE_20GBASE_KR2 BIT_ULL(I40E_PHY_TYPE_20GBASE_KR2)
+/* Defining the macro I40E_TYPE_OFFSET to implement a bit shift for some
+ * PHY types. There is an unused bit (31) in the I40E_CAP_PHY_TYPE_* bit
+ * fields but no corresponding gap in the i40e_aq_phy_type enumeration. So,
+ * a shift is needed to adjust for this with values larger than 31. The
+ * only affected values are I40E_PHY_TYPE_25GBASE_*.
+ */
+#define I40E_PHY_TYPE_OFFSET 1
+#define I40E_CAP_PHY_TYPE_25GBASE_KR BIT_ULL(I40E_PHY_TYPE_25GBASE_KR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_CR BIT_ULL(I40E_PHY_TYPE_25GBASE_CR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_SR BIT_ULL(I40E_PHY_TYPE_25GBASE_SR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_LR BIT_ULL(I40E_PHY_TYPE_25GBASE_LR + \
+ I40E_PHY_TYPE_OFFSET)
#define I40E_HW_CAP_MAX_GPIO 30
/* Capabilities of a PF or a VF or the whole device */
struct i40e_hw_capabilities {
diff --git a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
index 05ed49b..d28b684 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -2921,6 +2921,9 @@ int i40e_ndo_set_vf_bw(struct net_device *netdev, int vf_id, int min_tx_rate,
case I40E_LINK_SPEED_40GB:
speed = 40000;
break;
+ case I40E_LINK_SPEED_25GB:
+ speed = 25000;
+ break;
case I40E_LINK_SPEED_20GB:
speed = 20000;
break;
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h b/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
index 40b0eaf..f8d7d95 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h
@@ -1639,6 +1639,10 @@ enum i40e_aq_phy_type {
I40E_PHY_TYPE_1000BASE_LX = 0x1C,
I40E_PHY_TYPE_1000BASE_T_OPTICAL = 0x1D,
I40E_PHY_TYPE_20GBASE_KR2 = 0x1E,
+ I40E_PHY_TYPE_25GBASE_KR = 0x1F,
+ I40E_PHY_TYPE_25GBASE_CR = 0x20,
+ I40E_PHY_TYPE_25GBASE_SR = 0x21,
+ I40E_PHY_TYPE_25GBASE_LR = 0x22,
I40E_PHY_TYPE_MAX
};
@@ -1647,6 +1651,7 @@ enum i40e_aq_phy_type {
#define I40E_LINK_SPEED_10GB_SHIFT 0x3
#define I40E_LINK_SPEED_40GB_SHIFT 0x4
#define I40E_LINK_SPEED_20GB_SHIFT 0x5
+#define I40E_LINK_SPEED_25GB_SHIFT 0x6
enum i40e_aq_link_speed {
I40E_LINK_SPEED_UNKNOWN = 0,
@@ -1654,7 +1659,8 @@ enum i40e_aq_link_speed {
I40E_LINK_SPEED_1GB = BIT(I40E_LINK_SPEED_1000MB_SHIFT),
I40E_LINK_SPEED_10GB = BIT(I40E_LINK_SPEED_10GB_SHIFT),
I40E_LINK_SPEED_40GB = BIT(I40E_LINK_SPEED_40GB_SHIFT),
- I40E_LINK_SPEED_20GB = BIT(I40E_LINK_SPEED_20GB_SHIFT)
+ I40E_LINK_SPEED_20GB = BIT(I40E_LINK_SPEED_20GB_SHIFT),
+ I40E_LINK_SPEED_25GB = BIT(I40E_LINK_SPEED_25GB_SHIFT),
};
struct i40e_aqc_module_desc {
@@ -1687,7 +1693,13 @@ struct i40e_aq_get_phy_abilities_resp {
__le32 eeer_val;
u8 d3_lpan;
#define I40E_AQ_SET_PHY_D3_LPAN_ENA 0x01
- u8 reserved[3];
+ u8 phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR 0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
+ u8 mod_type_ext;
+ u8 ext_comp_code;
u8 phy_id[4];
u8 module_type[3];
u8 qualified_module_count;
@@ -1709,7 +1721,12 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
__le16 eee_capability;
__le32 eeer;
u8 low_power_ctrl;
- u8 reserved[3];
+ u8 phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR 0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR 0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR 0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR 0x08
+ u8 reserved[2];
};
I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1789,6 +1806,13 @@ struct i40e_aqc_get_link_status {
#define I40E_AQ_LINK_TX_DRAINED 0x01
#define I40E_AQ_LINK_TX_FLUSHED 0x03
#define I40E_AQ_LINK_FORCED_40G 0x10
+/* 25G Error Codes */
+#define I40E_AQ_25G_NO_ERR 0X00
+#define I40E_AQ_25G_NOT_PRESENT 0X01
+#define I40E_AQ_25G_NVM_CRC_ERR 0X02
+#define I40E_AQ_25G_SBUS_UCODE_ERR 0X03
+#define I40E_AQ_25G_SERDES_UCODE_ERR 0X04
+#define I40E_AQ_25G_NIMB_UCODE_ERR 0X05
u8 loopback; /* use defines from i40e_aqc_set_lb_mode */
__le16 max_frame_size;
u8 config;
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_common.c b/drivers/net/ethernet/intel/i40evf/i40e_common.c
index 7953c13..aa63b7f 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_common.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_common.c
@@ -53,6 +53,8 @@ i40e_status i40e_set_mac_type(struct i40e_hw *hw)
case I40E_DEV_ID_10G_BASE_T4:
case I40E_DEV_ID_20G_KR2:
case I40E_DEV_ID_20G_KR2_A:
+ case I40E_DEV_ID_25G_B:
+ case I40E_DEV_ID_25G_SFP28:
hw->mac.type = I40E_MAC_XL710;
break;
case I40E_DEV_ID_SFP_X722:
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_devids.h b/drivers/net/ethernet/intel/i40evf/i40e_devids.h
index 7023570..21dcaee 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_devids.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_devids.h
@@ -39,6 +39,8 @@
#define I40E_DEV_ID_20G_KR2 0x1587
#define I40E_DEV_ID_20G_KR2_A 0x1588
#define I40E_DEV_ID_10G_BASE_T4 0x1589
+#define I40E_DEV_ID_25G_B 0x158A
+#define I40E_DEV_ID_25G_SFP28 0x158B
#define I40E_DEV_ID_VF 0x154C
#define I40E_DEV_ID_VF_HV 0x1571
#define I40E_DEV_ID_SFP_X722 0x37D0
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_type.h b/drivers/net/ethernet/intel/i40evf/i40e_type.h
index 515484c..c85e8a3 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_type.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_type.h
@@ -187,47 +187,59 @@ struct i40e_link_status {
#define I40E_MODULE_TYPE_1000BASE_T 0x08
};
-enum i40e_aq_capabilities_phy_type {
- I40E_CAP_PHY_TYPE_SGMII = BIT(I40E_PHY_TYPE_SGMII),
- I40E_CAP_PHY_TYPE_1000BASE_KX = BIT(I40E_PHY_TYPE_1000BASE_KX),
- I40E_CAP_PHY_TYPE_10GBASE_KX4 = BIT(I40E_PHY_TYPE_10GBASE_KX4),
- I40E_CAP_PHY_TYPE_10GBASE_KR = BIT(I40E_PHY_TYPE_10GBASE_KR),
- I40E_CAP_PHY_TYPE_40GBASE_KR4 = BIT(I40E_PHY_TYPE_40GBASE_KR4),
- I40E_CAP_PHY_TYPE_XAUI = BIT(I40E_PHY_TYPE_XAUI),
- I40E_CAP_PHY_TYPE_XFI = BIT(I40E_PHY_TYPE_XFI),
- I40E_CAP_PHY_TYPE_SFI = BIT(I40E_PHY_TYPE_SFI),
- I40E_CAP_PHY_TYPE_XLAUI = BIT(I40E_PHY_TYPE_XLAUI),
- I40E_CAP_PHY_TYPE_XLPPI = BIT(I40E_PHY_TYPE_XLPPI),
- I40E_CAP_PHY_TYPE_40GBASE_CR4_CU = BIT(I40E_PHY_TYPE_40GBASE_CR4_CU),
- I40E_CAP_PHY_TYPE_10GBASE_CR1_CU = BIT(I40E_PHY_TYPE_10GBASE_CR1_CU),
- I40E_CAP_PHY_TYPE_10GBASE_AOC = BIT(I40E_PHY_TYPE_10GBASE_AOC),
- I40E_CAP_PHY_TYPE_40GBASE_AOC = BIT(I40E_PHY_TYPE_40GBASE_AOC),
- I40E_CAP_PHY_TYPE_100BASE_TX = BIT(I40E_PHY_TYPE_100BASE_TX),
- I40E_CAP_PHY_TYPE_1000BASE_T = BIT(I40E_PHY_TYPE_1000BASE_T),
- I40E_CAP_PHY_TYPE_10GBASE_T = BIT(I40E_PHY_TYPE_10GBASE_T),
- I40E_CAP_PHY_TYPE_10GBASE_SR = BIT(I40E_PHY_TYPE_10GBASE_SR),
- I40E_CAP_PHY_TYPE_10GBASE_LR = BIT(I40E_PHY_TYPE_10GBASE_LR),
- I40E_CAP_PHY_TYPE_10GBASE_SFPP_CU = BIT(I40E_PHY_TYPE_10GBASE_SFPP_CU),
- I40E_CAP_PHY_TYPE_10GBASE_CR1 = BIT(I40E_PHY_TYPE_10GBASE_CR1),
- I40E_CAP_PHY_TYPE_40GBASE_CR4 = BIT(I40E_PHY_TYPE_40GBASE_CR4),
- I40E_CAP_PHY_TYPE_40GBASE_SR4 = BIT(I40E_PHY_TYPE_40GBASE_SR4),
- I40E_CAP_PHY_TYPE_40GBASE_LR4 = BIT(I40E_PHY_TYPE_40GBASE_LR4),
- I40E_CAP_PHY_TYPE_1000BASE_SX = BIT(I40E_PHY_TYPE_1000BASE_SX),
- I40E_CAP_PHY_TYPE_1000BASE_LX = BIT(I40E_PHY_TYPE_1000BASE_LX),
- I40E_CAP_PHY_TYPE_1000BASE_T_OPTICAL =
- BIT(I40E_PHY_TYPE_1000BASE_T_OPTICAL),
- I40E_CAP_PHY_TYPE_20GBASE_KR2 = BIT(I40E_PHY_TYPE_20GBASE_KR2)
-};
-
struct i40e_phy_info {
struct i40e_link_status link_info;
struct i40e_link_status link_info_old;
bool get_link_info;
enum i40e_media_type media_type;
/* all the phy types the NVM is capable of */
- enum i40e_aq_capabilities_phy_type phy_types;
-};
-
+ u64 phy_types;
+};
+
+#define I40E_CAP_PHY_TYPE_SGMII BIT_ULL(I40E_PHY_TYPE_SGMII)
+#define I40E_CAP_PHY_TYPE_1000BASE_KX BIT_ULL(I40E_PHY_TYPE_1000BASE_KX)
+#define I40E_CAP_PHY_TYPE_10GBASE_KX4 BIT_ULL(I40E_PHY_TYPE_10GBASE_KX4)
+#define I40E_CAP_PHY_TYPE_10GBASE_KR BIT_ULL(I40E_PHY_TYPE_10GBASE_KR)
+#define I40E_CAP_PHY_TYPE_40GBASE_KR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_KR4)
+#define I40E_CAP_PHY_TYPE_XAUI BIT_ULL(I40E_PHY_TYPE_XAUI)
+#define I40E_CAP_PHY_TYPE_XFI BIT_ULL(I40E_PHY_TYPE_XFI)
+#define I40E_CAP_PHY_TYPE_SFI BIT_ULL(I40E_PHY_TYPE_SFI)
+#define I40E_CAP_PHY_TYPE_XLAUI BIT_ULL(I40E_PHY_TYPE_XLAUI)
+#define I40E_CAP_PHY_TYPE_XLPPI BIT_ULL(I40E_PHY_TYPE_XLPPI)
+#define I40E_CAP_PHY_TYPE_40GBASE_CR4_CU BIT_ULL(I40E_PHY_TYPE_40GBASE_CR4_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_CR1_CU BIT_ULL(I40E_PHY_TYPE_10GBASE_CR1_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_AOC BIT_ULL(I40E_PHY_TYPE_10GBASE_AOC)
+#define I40E_CAP_PHY_TYPE_40GBASE_AOC BIT_ULL(I40E_PHY_TYPE_40GBASE_AOC)
+#define I40E_CAP_PHY_TYPE_100BASE_TX BIT_ULL(I40E_PHY_TYPE_100BASE_TX)
+#define I40E_CAP_PHY_TYPE_1000BASE_T BIT_ULL(I40E_PHY_TYPE_1000BASE_T)
+#define I40E_CAP_PHY_TYPE_10GBASE_T BIT_ULL(I40E_PHY_TYPE_10GBASE_T)
+#define I40E_CAP_PHY_TYPE_10GBASE_SR BIT_ULL(I40E_PHY_TYPE_10GBASE_SR)
+#define I40E_CAP_PHY_TYPE_10GBASE_LR BIT_ULL(I40E_PHY_TYPE_10GBASE_LR)
+#define I40E_CAP_PHY_TYPE_10GBASE_SFPP_CU BIT_ULL(I40E_PHY_TYPE_10GBASE_SFPP_CU)
+#define I40E_CAP_PHY_TYPE_10GBASE_CR1 BIT_ULL(I40E_PHY_TYPE_10GBASE_CR1)
+#define I40E_CAP_PHY_TYPE_40GBASE_CR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_CR4)
+#define I40E_CAP_PHY_TYPE_40GBASE_SR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_SR4)
+#define I40E_CAP_PHY_TYPE_40GBASE_LR4 BIT_ULL(I40E_PHY_TYPE_40GBASE_LR4)
+#define I40E_CAP_PHY_TYPE_1000BASE_SX BIT_ULL(I40E_PHY_TYPE_1000BASE_SX)
+#define I40E_CAP_PHY_TYPE_1000BASE_LX BIT_ULL(I40E_PHY_TYPE_1000BASE_LX)
+#define I40E_CAP_PHY_TYPE_1000BASE_T_OPTICAL \
+ BIT_ULL(I40E_PHY_TYPE_1000BASE_T_OPTICAL)
+#define I40E_CAP_PHY_TYPE_20GBASE_KR2 BIT_ULL(I40E_PHY_TYPE_20GBASE_KR2)
+/* Defining the macro I40E_TYPE_OFFSET to implement a bit shift for some
+ * PHY types. There is an unused bit (31) in the I40E_CAP_PHY_TYPE_* bit
+ * fields but no corresponding gap in the i40e_aq_phy_type enumeration. So,
+ * a shift is needed to adjust for this with values larger than 31. The
+ * only affected values are I40E_PHY_TYPE_25GBASE_*.
+ */
+#define I40E_PHY_TYPE_OFFSET 1
+#define I40E_CAP_PHY_TYPE_25GBASE_KR BIT_ULL(I40E_PHY_TYPE_25GBASE_KR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_CR BIT_ULL(I40E_PHY_TYPE_25GBASE_CR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_SR BIT_ULL(I40E_PHY_TYPE_25GBASE_SR + \
+ I40E_PHY_TYPE_OFFSET)
+#define I40E_CAP_PHY_TYPE_25GBASE_LR BIT_ULL(I40E_PHY_TYPE_25GBASE_LR + \
+ I40E_PHY_TYPE_OFFSET)
#define I40E_HW_CAP_MAX_GPIO 30
/* Capabilities of a PF or a VF or the whole device */
struct i40e_hw_capabilities {
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c b/drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c
index a994015..272d600 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c
+++ b/drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c
@@ -85,6 +85,14 @@ static int i40evf_get_settings(struct net_device *netdev,
case I40E_LINK_SPEED_40GB:
ethtool_cmd_speed_set(ecmd, SPEED_40000);
break;
+ case I40E_LINK_SPEED_25GB:
+#ifdef SPEED_25000
+ ethtool_cmd_speed_set(ecmd, SPEED_25000);
+#else
+ netdev_info(netdev,
+ "Speed is 25G, display not supported by this version of ethtool.\n");
+#endif
+ break;
case I40E_LINK_SPEED_20GB:
ethtool_cmd_speed_set(ecmd, SPEED_20000);
break;
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c b/drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
index ddf478d..2059a8e 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
+++ b/drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
@@ -836,6 +836,9 @@ static void i40evf_print_link_message(struct i40evf_adapter *adapter)
case I40E_LINK_SPEED_40GB:
speed = "40 G";
break;
+ case I40E_LINK_SPEED_25GB:
+ speed = "25 G";
+ break;
case I40E_LINK_SPEED_20GB:
speed = "20 G";
break;
--
2.9.3
^ permalink raw reply related
* [net-next v2 11/19] i40e: Add functions which apply correct PHY access method for read and write operation
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Michal Kosiarz, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Michal Kosiarz <michal.kosiarz@intel.com>
Depending on external PHY type, register access method should be
different. Clause22 or Clause45 can be chosen for different PHYs.
Implemented functions apply correct access method for used device.
Change-ID: If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_common.c | 72 ++++++++++++++++++++++
drivers/net/ethernet/intel/i40e/i40e_prototype.h | 4 ++
drivers/net/ethernet/intel/i40evf/i40e_prototype.h | 4 ++
3 files changed, 80 insertions(+)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_common.c b/drivers/net/ethernet/intel/i40e/i40e_common.c
index f8c4c14..1287359 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_common.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_common.c
@@ -4676,6 +4676,78 @@ i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw,
}
/**
+ * i40e_write_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Writes value to specified PHY register
+ **/
+i40e_status i40e_write_phy_register(struct i40e_hw *hw,
+ u8 page, u16 reg, u8 phy_addr, u16 value)
+{
+ i40e_status status;
+
+ switch (hw->device_id) {
+ case I40E_DEV_ID_1G_BASE_T_X722:
+ status = i40e_write_phy_register_clause22(hw, reg, phy_addr,
+ value);
+ break;
+ case I40E_DEV_ID_10G_BASE_T:
+ case I40E_DEV_ID_10G_BASE_T4:
+ case I40E_DEV_ID_10G_BASE_T_X722:
+ case I40E_DEV_ID_25G_B:
+ case I40E_DEV_ID_25G_SFP28:
+ status = i40e_write_phy_register_clause45(hw, page, reg,
+ phy_addr, value);
+ break;
+ default:
+ status = I40E_ERR_UNKNOWN_PHY;
+ break;
+ }
+
+ return status;
+}
+
+/**
+ * i40e_read_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Reads specified PHY register value
+ **/
+i40e_status i40e_read_phy_register(struct i40e_hw *hw,
+ u8 page, u16 reg, u8 phy_addr, u16 *value)
+{
+ i40e_status status;
+
+ switch (hw->device_id) {
+ case I40E_DEV_ID_1G_BASE_T_X722:
+ status = i40e_read_phy_register_clause22(hw, reg, phy_addr,
+ value);
+ break;
+ case I40E_DEV_ID_10G_BASE_T:
+ case I40E_DEV_ID_10G_BASE_T4:
+ case I40E_DEV_ID_10G_BASE_T_X722:
+ case I40E_DEV_ID_25G_B:
+ case I40E_DEV_ID_25G_SFP28:
+ status = i40e_read_phy_register_clause45(hw, page, reg,
+ phy_addr, value);
+ break;
+ default:
+ status = I40E_ERR_UNKNOWN_PHY;
+ break;
+ }
+
+ return status;
+}
+
+/**
* i40e_get_phy_address
* @hw: pointer to the HW structure
* @dev_num: PHY port num that address we want
diff --git a/drivers/net/ethernet/intel/i40e/i40e_prototype.h b/drivers/net/ethernet/intel/i40e/i40e_prototype.h
index 37d67e7..2551fc8 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_prototype.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_prototype.h
@@ -373,6 +373,10 @@ i40e_status i40e_read_phy_register_clause45(struct i40e_hw *hw,
u8 page, u16 reg, u8 phy_addr, u16 *value);
i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw,
u8 page, u16 reg, u8 phy_addr, u16 value);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+ u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+ u8 phy_addr, u16 value);
u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
u32 time, u32 interval);
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_prototype.h b/drivers/net/ethernet/intel/i40evf/i40e_prototype.h
index d89d521..ba6c6bd 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_prototype.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_prototype.h
@@ -115,6 +115,10 @@ i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page,
u16 reg, u8 phy_addr, u16 *value);
i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page,
u16 reg, u8 phy_addr, u16 value);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+ u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+ u8 phy_addr, u16 value);
u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
u32 time, u32 interval);
--
2.9.3
^ permalink raw reply related
* [net-next v2 12/19] i40e: lock service task correctly
From: Jeff Kirsher @ 2016-12-07 22:19 UTC (permalink / raw)
To: davem
Cc: Mitch Williams, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161207221918.57932-1-jeffrey.t.kirsher@intel.com>
From: Mitch Williams <mitch.a.williams@intel.com>
The service task lock was being set in the scheduling function, not the
actual service task. This would potentially leave the bit set for a long
time before the task actually ran. Furthermore, if the service task
takes too long, it calls the schedule function to reschedule itself -
which would fail to take the lock and do nothing.
Instead, set and clear the lock bit in the service task itself. In the
process, get rid of the i40e_service_event_complete() function, which is
really just two lines of code that can be put right in the service task
itself.
Change-ID: I83155e682b686121e2897f4429eb7d3f7c669168
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 24 +++++++-----------------
1 file changed, 7 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index b0486c9..c47e9c5 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -288,8 +288,7 @@ struct i40e_vsi *i40e_find_vsi_from_id(struct i40e_pf *pf, u16 id)
void i40e_service_event_schedule(struct i40e_pf *pf)
{
if (!test_bit(__I40E_DOWN, &pf->state) &&
- !test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state) &&
- !test_and_set_bit(__I40E_SERVICE_SCHED, &pf->state))
+ !test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state))
queue_work(i40e_wq, &pf->service_task);
}
@@ -5955,19 +5954,6 @@ static void i40e_handle_lan_overflow_event(struct i40e_pf *pf,
}
/**
- * i40e_service_event_complete - Finish up the service event
- * @pf: board private structure
- **/
-static void i40e_service_event_complete(struct i40e_pf *pf)
-{
- WARN_ON(!test_bit(__I40E_SERVICE_SCHED, &pf->state));
-
- /* flush memory to make sure state is correct before next watchog */
- smp_mb__before_atomic();
- clear_bit(__I40E_SERVICE_SCHED, &pf->state);
-}
-
-/**
* i40e_get_cur_guaranteed_fd_count - Get the consumed guaranteed FD filters
* @pf: board private structure
**/
@@ -7276,10 +7262,12 @@ static void i40e_service_task(struct work_struct *work)
/* don't bother with service tasks if a reset is in progress */
if (test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state)) {
- i40e_service_event_complete(pf);
return;
}
+ if (test_and_set_bit(__I40E_SERVICE_SCHED, &pf->state))
+ return;
+
i40e_detect_recover_hung(pf);
i40e_sync_filters_subtask(pf);
i40e_reset_subtask(pf);
@@ -7292,7 +7280,9 @@ static void i40e_service_task(struct work_struct *work)
i40e_sync_udp_filters_subtask(pf);
i40e_clean_adminq_subtask(pf);
- i40e_service_event_complete(pf);
+ /* flush memory to make sure state is correct before next watchdog */
+ smp_mb__before_atomic();
+ clear_bit(__I40E_SERVICE_SCHED, &pf->state);
/* If the tasks have taken longer than one timer cycle or there
* is more work to be done, reschedule the service task now
--
2.9.3
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox