* [net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Don Skidmore, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Don Skidmore <donald.c.skidmore@intel.com>
This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane. Without this patch the link remains at
1G when resuming form low power after being downshifted by LPLU.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 92f2b5e..675c198 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -2187,12 +2187,11 @@ static s32 ixgbe_setup_kx4_x550em(struct ixgbe_hw *hw)
/**
* ixgbe_setup_kr_x550em - Configure the KR PHY
* @hw: pointer to hardware structure
- *
- * Configures the integrated KR PHY for X550EM_x.
**/
static s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
{
- if (hw->mac.type != ixgbe_mac_X550EM_x)
+ /* leave linke alone for 2.5G */
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL)
return 0;
return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
--
2.9.3
^ permalink raw reply related
* [net-next 16/21] ixgbe: Fix issues with EEPROM access
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Mark Rustad, netdev, nhorman, sassmann, jogreene, guru.anbalagane,
Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Mark Rustad <mark.d.rustad@intel.com>
There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.
Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 97 ++++++++++++++++---------
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h | 1 +
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 75 +++++++------------
3 files changed, 91 insertions(+), 82 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 5d8f1ae..851f485 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -3593,43 +3593,29 @@ u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
}
/**
- * ixgbe_host_interface_command - Issue command to manageability block
+ * ixgbe_hic_unlocked - Issue command to manageability block unlocked
* @hw: pointer to the HW structure
- * @buffer: contains the command to write and where the return status will
- * be placed
+ * @buffer: command to write and where the return status will be placed
* @length: length of buffer, must be multiple of 4 bytes
* @timeout: time in ms to wait for command completion
- * @return_data: read and return data from the buffer (true) or not (false)
- * Needed because FW structures are big endian and decoding of
- * these fields can be 8 bit or 16 bit based on command. Decoding
- * is not easily understood without making a table of commands.
- * So we will leave this up to the caller to read back the data
- * in these cases.
*
- * Communicates with the manageability block. On success return 0
- * else return IXGBE_ERR_HOST_INTERFACE_COMMAND.
+ * Communicates with the manageability block. On success return 0
+ * else returns semaphore error when encountering an error acquiring
+ * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *
+ * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
+ * by the caller.
**/
-s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
- u32 length, u32 timeout,
- bool return_data)
+s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
+ u32 timeout)
{
- u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
- u32 hicr, i, bi, fwsts;
- u16 buf_len, dword_len;
- union {
- struct ixgbe_hic_hdr hdr;
- u32 u32arr[1];
- } *bp = buffer;
- s32 status;
+ u32 hicr, i, fwsts;
+ u16 dword_len;
if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
- /* Take management host interface semaphore */
- status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
- if (status)
- return status;
/* Set bit 9 of FWSTS clearing FW reset indication */
fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
@@ -3639,15 +3625,13 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
if (!(hicr & IXGBE_HICR_EN)) {
hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
- status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
- goto rel_out;
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
/* Calculate length in DWORDs. We must be DWORD aligned */
if (length % sizeof(u32)) {
hw_dbg(hw, "Buffer length failure, not aligned to dword");
- status = IXGBE_ERR_INVALID_ARGUMENT;
- goto rel_out;
+ return IXGBE_ERR_INVALID_ARGUMENT;
}
dword_len = length >> 2;
@@ -3657,7 +3641,7 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
*/
for (i = 0; i < dword_len; i++)
IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
- i, cpu_to_le32(bp->u32arr[i]));
+ i, cpu_to_le32(buffer[i]));
/* Setting this bit tells the ARC that a new command is pending. */
IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);
@@ -3671,11 +3655,54 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
/* Check command successful completion. */
if ((timeout && i == timeout) ||
- !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) {
- hw_dbg(hw, "Command has failed with no status valid.\n");
- status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
- goto rel_out;
+ !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+
+ return 0;
+}
+
+/**
+ * ixgbe_host_interface_command - Issue command to manageability block
+ * @hw: pointer to the HW structure
+ * @buffer: contains the command to write and where the return status will
+ * be placed
+ * @length: length of buffer, must be multiple of 4 bytes
+ * @timeout: time in ms to wait for command completion
+ * @return_data: read and return data from the buffer (true) or not (false)
+ * Needed because FW structures are big endian and decoding of
+ * these fields can be 8 bit or 16 bit based on command. Decoding
+ * is not easily understood without making a table of commands.
+ * So we will leave this up to the caller to read back the data
+ * in these cases.
+ *
+ * Communicates with the manageability block. On success return 0
+ * else return IXGBE_ERR_HOST_INTERFACE_COMMAND.
+ **/
+s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
+ u32 length, u32 timeout,
+ bool return_data)
+{
+ u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
+ union {
+ struct ixgbe_hic_hdr hdr;
+ u32 u32arr[1];
+ } *bp = buffer;
+ u16 buf_len, dword_len;
+ s32 status;
+ u32 bi;
+
+ if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
+ hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
+ /* Take management host interface semaphore */
+ status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
+ if (status)
+ return status;
+
+ status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
+ if (status)
+ goto rel_out;
if (!return_data)
goto rel_out;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index 393aeab..671a0cd 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -115,6 +115,7 @@ s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
u8 ixgbe_calculate_checksum(u8 *buffer, u32 length);
s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *, u32 length,
u32 timeout, bool return_data);
+s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 len, u32 timeout);
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
bool ixgbe_mng_present(struct ixgbe_hw *hw);
bool ixgbe_mng_enabled(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 675c198..d2fee52 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -624,41 +624,6 @@ static s32 ixgbe_read_iosf_sb_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
return status;
}
-/** ixgbe_read_ee_hostif_data_X550 - Read EEPROM word using a host interface
- * command assuming that the semaphore is already obtained.
- * @hw: pointer to hardware structure
- * @offset: offset of word in the EEPROM to read
- * @data: word read from the EEPROM
- *
- * Reads a 16 bit word from the EEPROM using the hostif.
- **/
-static s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
- u16 *data)
-{
- s32 status;
- struct ixgbe_hic_read_shadow_ram buffer;
-
- buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
- buffer.hdr.req.buf_lenh = 0;
- buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
- buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
-
- /* convert offset from words to bytes */
- buffer.address = cpu_to_be32(offset * 2);
- /* one word */
- buffer.length = cpu_to_be16(sizeof(u16));
-
- status = ixgbe_host_interface_command(hw, &buffer, sizeof(buffer),
- IXGBE_HI_COMMAND_TIMEOUT, false);
- if (status)
- return status;
-
- *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
- FW_NVM_DATA_OFFSET);
-
- return 0;
-}
-
/** ixgbe_read_ee_hostif_buffer_X550- Read EEPROM word(s) using hostif
* @hw: pointer to hardware structure
* @offset: offset of word in the EEPROM to read
@@ -670,6 +635,7 @@ static s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
u16 offset, u16 words, u16 *data)
{
+ const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
struct ixgbe_hic_read_shadow_ram buffer;
u32 current_word = 0;
u16 words_to_read;
@@ -677,7 +643,7 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
u32 i;
/* Take semaphore for the entire operation. */
- status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ status = hw->mac.ops.acquire_swfw_sync(hw, mask);
if (status) {
hw_dbg(hw, "EEPROM read buffer - semaphore failed\n");
return status;
@@ -698,10 +664,8 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
buffer.address = cpu_to_be32((offset + current_word) * 2);
buffer.length = cpu_to_be16(words_to_read * 2);
- status = ixgbe_host_interface_command(hw, &buffer,
- sizeof(buffer),
- IXGBE_HI_COMMAND_TIMEOUT,
- false);
+ status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT);
if (status) {
hw_dbg(hw, "Host interface command failed\n");
goto out;
@@ -725,7 +689,7 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
}
out:
- hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ hw->mac.ops.release_swfw_sync(hw, mask);
return status;
}
@@ -896,15 +860,32 @@ static s32 ixgbe_calc_eeprom_checksum_X550(struct ixgbe_hw *hw)
**/
static s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 *data)
{
- s32 status = 0;
+ const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
+ struct ixgbe_hic_read_shadow_ram buffer;
+ s32 status;
- if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) == 0) {
- status = ixgbe_read_ee_hostif_data_X550(hw, offset, data);
- hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
- } else {
- status = IXGBE_ERR_SWFW_SYNC;
+ buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+ buffer.hdr.req.buf_lenh = 0;
+ buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+ buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+ /* convert offset from words to bytes */
+ buffer.address = cpu_to_be32(offset * 2);
+ /* one word */
+ buffer.length = cpu_to_be16(sizeof(u16));
+
+ status = hw->mac.ops.acquire_swfw_sync(hw, mask);
+ if (status)
+ return status;
+
+ status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT);
+ if (!status) {
+ *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+ FW_NVM_DATA_OFFSET);
}
+ hw->mac.ops.release_swfw_sync(hw, mask);
return status;
}
--
2.9.3
^ permalink raw reply related
* [net-next 17/21] ixgbe: Remove unused firmware version functions and method
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Mark Rustad, netdev, nhorman, sassmann, jogreene, guru.anbalagane,
Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Mark Rustad <mark.d.rustad@intel.com>
The firmware version method and functions are not used anywhere, so
remove them all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c | 2 --
drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c | 2 --
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 34 --------------------------
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h | 4 ---
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 1 -
drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c | 1 -
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 3 +--
7 files changed, 1 insertion(+), 46 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
index 805ab31..523f9d0 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
@@ -139,8 +139,6 @@ static s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw)
case ixgbe_phy_tn:
phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
phy->ops.check_link = &ixgbe_check_phy_link_tnx;
- phy->ops.get_firmware_version =
- &ixgbe_get_phy_firmware_version_tnx;
break;
case ixgbe_phy_nl:
phy->ops.reset = &ixgbe_reset_phy_nl;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
index e00aaeb..30535e6 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -331,8 +331,6 @@ static s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw)
case ixgbe_phy_tn:
phy->ops.check_link = &ixgbe_check_phy_link_tnx;
phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
- phy->ops.get_firmware_version =
- &ixgbe_get_phy_firmware_version_tnx;
break;
default:
break;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index 019b3c2..67a399b 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -977,40 +977,6 @@ s32 ixgbe_setup_phy_link_tnx(struct ixgbe_hw *hw)
}
/**
- * ixgbe_get_phy_firmware_version_tnx - Gets the PHY Firmware Version
- * @hw: pointer to hardware structure
- * @firmware_version: pointer to the PHY Firmware Version
- **/
-s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
- u16 *firmware_version)
-{
- s32 status;
-
- status = hw->phy.ops.read_reg(hw, TNX_FW_REV,
- MDIO_MMD_VEND1,
- firmware_version);
-
- return status;
-}
-
-/**
- * ixgbe_get_phy_firmware_version_generic - Gets the PHY Firmware Version
- * @hw: pointer to hardware structure
- * @firmware_version: pointer to the PHY Firmware Version
- **/
-s32 ixgbe_get_phy_firmware_version_generic(struct ixgbe_hw *hw,
- u16 *firmware_version)
-{
- s32 status;
-
- status = hw->phy.ops.read_reg(hw, AQ_FW_REV,
- MDIO_MMD_VEND1,
- firmware_version);
-
- return status;
-}
-
-/**
* ixgbe_reset_phy_nl - Performs a PHY reset
* @hw: pointer to hardware structure
**/
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
index ecf05f8..5aa2c3c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -168,10 +168,6 @@ s32 ixgbe_check_phy_link_tnx(struct ixgbe_hw *hw,
ixgbe_link_speed *speed,
bool *link_up);
s32 ixgbe_setup_phy_link_tnx(struct ixgbe_hw *hw);
-s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
- u16 *firmware_version);
-s32 ixgbe_get_phy_firmware_version_generic(struct ixgbe_hw *hw,
- u16 *firmware_version);
s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw);
s32 ixgbe_set_copper_phy_power(struct ixgbe_hw *hw, bool on);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 0d85511..5c59b3c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -3404,7 +3404,6 @@ struct ixgbe_phy_operations {
s32 (*setup_internal_link)(struct ixgbe_hw *);
s32 (*setup_link_speed)(struct ixgbe_hw *, ixgbe_link_speed, bool);
s32 (*check_link)(struct ixgbe_hw *, ixgbe_link_speed *, bool *);
- s32 (*get_firmware_version)(struct ixgbe_hw *, u16 *);
s32 (*read_i2c_byte)(struct ixgbe_hw *, u8, u8, u8 *);
s32 (*write_i2c_byte)(struct ixgbe_hw *, u8, u8, u8);
s32 (*read_i2c_sff8472)(struct ixgbe_hw *, u8 , u8 *);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
index afc4d16..84a467a 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
@@ -918,7 +918,6 @@ static const struct ixgbe_phy_operations phy_ops_X540 = {
.write_i2c_eeprom = &ixgbe_write_i2c_eeprom_generic,
.check_overtemp = &ixgbe_tn_check_overtemp,
.set_phy_power = &ixgbe_set_copper_phy_power,
- .get_firmware_version = &ixgbe_get_phy_firmware_version_generic,
};
static const u32 ixgbe_mvals_X540[IXGBE_MVALS_IDX_LIMIT] = {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index d2fee52..3c3bf48 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -3419,8 +3419,7 @@ static const struct ixgbe_eeprom_operations eeprom_ops_X550EM_x = {
.write_i2c_eeprom = &ixgbe_write_i2c_eeprom_generic, \
.setup_link = &ixgbe_setup_phy_link_generic, \
.set_phy_power = NULL, \
- .check_overtemp = &ixgbe_tn_check_overtemp, \
- .get_firmware_version = &ixgbe_get_phy_firmware_version_generic,
+ .check_overtemp = &ixgbe_tn_check_overtemp,
static const struct ixgbe_phy_operations phy_ops_X550 = {
X550_COMMON_PHY
--
2.9.3
^ permalink raw reply related
* [net-next 14/21] ixgbevf: restore hw_addr on resume or error
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Emil Tantilov, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Emil Tantilov <emil.s.tantilov@intel.com>
Restore adapter->hw.hw_addr after handling an error, or a resume
operation to make sure we can access the registers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 7dfd1df..544307c 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -3851,6 +3851,8 @@ static int ixgbevf_resume(struct pci_dev *pdev)
dev_err(&pdev->dev, "Cannot enable PCI device from suspend\n");
return err;
}
+
+ adapter->hw.hw_addr = adapter->io_addr;
smp_mb__before_atomic();
clear_bit(__IXGBEVF_DISABLED, &adapter->state);
pci_set_master(pdev);
@@ -4285,6 +4287,7 @@ static pci_ers_result_t ixgbevf_io_slot_reset(struct pci_dev *pdev)
return PCI_ERS_RESULT_DISCONNECT;
}
+ adapter->hw.hw_addr = adapter->io_addr;
smp_mb__before_atomic();
clear_bit(__IXGBEVF_DISABLED, &adapter->state);
pci_set_master(pdev);
--
2.9.3
^ permalink raw reply related
* [net-next 18/21] ixgbe: Implement firmware interface to access some PHYs
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Mark Rustad, netdev, nhorman, sassmann, jogreene, guru.anbalagane,
Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Mark Rustad <mark.d.rustad@intel.com>
Implement new interface for firmware commands to access some PHYs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h | 2 +
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 66 +++++++++++++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 45 +++++++++++++++++
3 files changed, 113 insertions(+)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index 671a0cd..e083732 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -116,6 +116,8 @@ u8 ixgbe_calculate_checksum(u8 *buffer, u32 length);
s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *, u32 length,
u32 timeout, bool return_data);
s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 len, u32 timeout);
+s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
+ u32 (*data)[FW_PHY_ACT_DATA_COUNT]);
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
bool ixgbe_mng_present(struct ixgbe_hw *hw);
bool ixgbe_mng_enabled(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 5c59b3c..a8f2d70 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -2645,6 +2645,59 @@ enum ixgbe_fdir_pballoc_type {
#define FW_INT_PHY_REQ_LEN 10
#define FW_INT_PHY_REQ_READ 0
#define FW_INT_PHY_REQ_WRITE 1
+#define FW_PHY_ACT_REQ_CMD 5
+#define FW_PHY_ACT_DATA_COUNT 4
+#define FW_PHY_ACT_REQ_LEN (4 + 4 * FW_PHY_ACT_DATA_COUNT)
+#define FW_PHY_ACT_INIT_PHY 1
+#define FW_PHY_ACT_SETUP_LINK 2
+#define FW_PHY_ACT_LINK_SPEED_10 BIT(0)
+#define FW_PHY_ACT_LINK_SPEED_100 BIT(1)
+#define FW_PHY_ACT_LINK_SPEED_1G BIT(2)
+#define FW_PHY_ACT_LINK_SPEED_2_5G BIT(3)
+#define FW_PHY_ACT_LINK_SPEED_5G BIT(4)
+#define FW_PHY_ACT_LINK_SPEED_10G BIT(5)
+#define FW_PHY_ACT_LINK_SPEED_20G BIT(6)
+#define FW_PHY_ACT_LINK_SPEED_25G BIT(7)
+#define FW_PHY_ACT_LINK_SPEED_40G BIT(8)
+#define FW_PHY_ACT_LINK_SPEED_50G BIT(9)
+#define FW_PHY_ACT_LINK_SPEED_100G BIT(10)
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT 16
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_MASK (3 << \
+ HW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT)
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_NONE 0u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_TX 1u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_RX 2u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX 3u
+#define FW_PHY_ACT_SETUP_LINK_LP BIT(18)
+#define FW_PHY_ACT_SETUP_LINK_HP BIT(19)
+#define FW_PHY_ACT_SETUP_LINK_EEE BIT(20)
+#define FW_PHY_ACT_SETUP_LINK_AN BIT(22)
+#define FW_PHY_ACT_SETUP_LINK_RSP_DOWN BIT(0)
+#define FW_PHY_ACT_GET_LINK_INFO 3
+#define FW_PHY_ACT_GET_LINK_INFO_EEE BIT(19)
+#define FW_PHY_ACT_GET_LINK_INFO_FC_TX BIT(20)
+#define FW_PHY_ACT_GET_LINK_INFO_FC_RX BIT(21)
+#define FW_PHY_ACT_GET_LINK_INFO_POWER BIT(22)
+#define FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE BIT(24)
+#define FW_PHY_ACT_GET_LINK_INFO_TEMP BIT(25)
+#define FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX BIT(28)
+#define FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX BIT(29)
+#define FW_PHY_ACT_FORCE_LINK_DOWN 4
+#define FW_PHY_ACT_FORCE_LINK_DOWN_OFF BIT(0)
+#define FW_PHY_ACT_PHY_SW_RESET 5
+#define FW_PHY_ACT_PHY_HW_RESET 6
+#define FW_PHY_ACT_GET_PHY_INFO 7
+#define FW_PHY_ACT_UD_2 0x1002
+#define FW_PHY_ACT_UD_2_10G_KR_EEE BIT(6)
+#define FW_PHY_ACT_UD_2_10G_KX4_EEE BIT(5)
+#define FW_PHY_ACT_UD_2_1G_KX_EEE BIT(4)
+#define FW_PHY_ACT_UD_2_10G_T_EEE BIT(3)
+#define FW_PHY_ACT_UD_2_1G_T_EEE BIT(2)
+#define FW_PHY_ACT_UD_2_100M_TX_EEE BIT(1)
+#define FW_PHY_ACT_RETRIES 50
+#define FW_PHY_INFO_SPEED_MASK 0xFFFu
+#define FW_PHY_INFO_ID_HI_MASK 0xFFFF0000u
+#define FW_PHY_INFO_ID_LO_MASK 0x0000FFFFu
/* Host Interface Command Structures */
struct ixgbe_hic_hdr {
@@ -2745,6 +2798,19 @@ struct ixgbe_hic_internal_phy_resp {
__be32 read_data;
};
+struct ixgbe_hic_phy_activity_req {
+ struct ixgbe_hic_hdr hdr;
+ u8 port_number;
+ u8 pad;
+ __le16 activity_id;
+ __be32 data[FW_PHY_ACT_DATA_COUNT];
+};
+
+struct ixgbe_hic_phy_activity_resp {
+ struct ixgbe_hic_hdr hdr;
+ __be32 data[FW_PHY_ACT_DATA_COUNT];
+};
+
/* Transmit Descriptor - Advanced */
union ixgbe_adv_tx_desc {
struct {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 3c3bf48..b9277df 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -402,6 +402,51 @@ ixgbe_write_i2c_combined_generic_unlocked(struct ixgbe_hw *hw,
return ixgbe_write_i2c_combined_generic_int(hw, addr, reg, val, false);
}
+/**
+ * ixgbe_fw_phy_activity - Perform an activity on a PHY
+ * @hw: pointer to hardware structure
+ * @activity: activity to perform
+ * @data: Pointer to 4 32-bit words of data
+ */
+s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
+ u32 (*data)[FW_PHY_ACT_DATA_COUNT])
+{
+ union {
+ struct ixgbe_hic_phy_activity_req cmd;
+ struct ixgbe_hic_phy_activity_resp rsp;
+ } hic;
+ u16 retries = FW_PHY_ACT_RETRIES;
+ s32 rc;
+ u32 i;
+
+ do {
+ memset(&hic, 0, sizeof(hic));
+ hic.cmd.hdr.cmd = FW_PHY_ACT_REQ_CMD;
+ hic.cmd.hdr.buf_len = FW_PHY_ACT_REQ_LEN;
+ hic.cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
+ hic.cmd.port_number = hw->bus.lan_id;
+ hic.cmd.activity_id = cpu_to_le16(activity);
+ for (i = 0; i < ARRAY_SIZE(hic.cmd.data); ++i)
+ hic.cmd.data[i] = cpu_to_be32((*data)[i]);
+
+ rc = ixgbe_host_interface_command(hw, &hic.cmd, sizeof(hic.cmd),
+ IXGBE_HI_COMMAND_TIMEOUT,
+ true);
+ if (rc)
+ return rc;
+ if (hic.rsp.hdr.cmd_or_resp.ret_status ==
+ FW_CEM_RESP_STATUS_SUCCESS) {
+ for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i)
+ (*data)[i] = be32_to_cpu(hic.rsp.data[i]);
+ return 0;
+ }
+ usleep_range(20, 30);
+ --retries;
+ } while (retries > 0);
+
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+}
+
/** ixgbe_init_eeprom_params_X550 - Initialize EEPROM params
* @hw: pointer to hardware structure
*
--
2.9.3
^ permalink raw reply related
* [net-next 20/21] ixgbevf: Add support for VF promiscuous mode
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Don Skidmore, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Don Skidmore <donald.c.skidmore@intel.com>
This patch extends the mailbox message to allow for VF promiscuous
mode support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbevf/ixgbevf.h | 1 +
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 15 +++++++++++++-
drivers/net/ethernet/intel/ixgbevf/mbx.h | 1 +
drivers/net/ethernet/intel/ixgbevf/vf.c | 24 +++++++++++++++++++----
4 files changed, 36 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h b/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
index 5639fbe..3fe6504 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
@@ -464,6 +464,7 @@ enum ixgbevf_xcast_modes {
IXGBEVF_XCAST_MODE_NONE = 0,
IXGBEVF_XCAST_MODE_MULTI,
IXGBEVF_XCAST_MODE_ALLMULTI,
+ IXGBEVF_XCAST_MODE_PROMISC,
};
extern const struct ixgbevf_info ixgbevf_82599_vf_info;
diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 544307c..dbdd938 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -1930,6 +1930,16 @@ static void ixgbevf_set_rx_mode(struct net_device *netdev)
(flags & (IFF_BROADCAST | IFF_MULTICAST)) ?
IXGBEVF_XCAST_MODE_MULTI : IXGBEVF_XCAST_MODE_NONE;
+ /* request the most inclusive mode we need */
+ if (flags & IFF_PROMISC)
+ xcast_mode = IXGBEVF_XCAST_MODE_PROMISC;
+ else if (flags & IFF_ALLMULTI)
+ xcast_mode = IXGBEVF_XCAST_MODE_ALLMULTI;
+ else if (flags & (IFF_BROADCAST | IFF_MULTICAST))
+ xcast_mode = IXGBEVF_XCAST_MODE_MULTI;
+ else
+ xcast_mode = IXGBEVF_XCAST_MODE_NONE;
+
spin_lock_bh(&adapter->mbx_lock);
hw->mac.ops.update_xcast_mode(hw, xcast_mode);
@@ -2071,7 +2081,8 @@ static void ixgbevf_init_last_counter_stats(struct ixgbevf_adapter *adapter)
static void ixgbevf_negotiate_api(struct ixgbevf_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
- int api[] = { ixgbe_mbox_api_12,
+ int api[] = { ixgbe_mbox_api_13,
+ ixgbe_mbox_api_12,
ixgbe_mbox_api_11,
ixgbe_mbox_api_10,
ixgbe_mbox_api_unknown };
@@ -2373,6 +2384,7 @@ static void ixgbevf_set_num_queues(struct ixgbevf_adapter *adapter)
switch (hw->api_version) {
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
adapter->num_rx_queues = rss;
adapter->num_tx_queues = rss;
default:
@@ -4117,6 +4129,7 @@ static int ixgbevf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
switch (adapter->hw.api_version) {
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
netdev->max_mtu = IXGBE_MAX_JUMBO_FRAME_SIZE -
(ETH_HLEN + ETH_FCS_LEN);
break;
diff --git a/drivers/net/ethernet/intel/ixgbevf/mbx.h b/drivers/net/ethernet/intel/ixgbevf/mbx.h
index 340cdd4..bc0442a 100644
--- a/drivers/net/ethernet/intel/ixgbevf/mbx.h
+++ b/drivers/net/ethernet/intel/ixgbevf/mbx.h
@@ -84,6 +84,7 @@ enum ixgbe_pfvf_api_rev {
ixgbe_mbox_api_20, /* API version 2.0, solaris Phase1 VF driver */
ixgbe_mbox_api_11, /* API version 1.1, linux/freebsd VF driver */
ixgbe_mbox_api_12, /* API version 1.2, linux/freebsd VF driver */
+ ixgbe_mbox_api_13, /* API version 1.3, linux/freebsd VF driver */
/* This value should always be last */
ixgbe_mbox_api_unknown, /* indicates that API version is not known */
};
diff --git a/drivers/net/ethernet/intel/ixgbevf/vf.c b/drivers/net/ethernet/intel/ixgbevf/vf.c
index d46ba1d..8a5db9d 100644
--- a/drivers/net/ethernet/intel/ixgbevf/vf.c
+++ b/drivers/net/ethernet/intel/ixgbevf/vf.c
@@ -330,9 +330,14 @@ int ixgbevf_get_reta_locked(struct ixgbe_hw *hw, u32 *reta, int num_rx_queues)
* Thus return an error if API doesn't support RETA querying or querying
* is not supported for this device type.
*/
- if (hw->api_version != ixgbe_mbox_api_12 ||
- hw->mac.type >= ixgbe_mac_X550_vf)
+ switch (hw->api_version) {
+ case ixgbe_mbox_api_13:
+ case ixgbe_mbox_api_12:
+ if (hw->mac.type >= ixgbe_mac_X550_vf)
+ break;
+ default:
return -EOPNOTSUPP;
+ }
msgbuf[0] = IXGBE_VF_GET_RETA;
@@ -391,9 +396,14 @@ int ixgbevf_get_rss_key_locked(struct ixgbe_hw *hw, u8 *rss_key)
* Thus return an error if API doesn't support RSS Random Key retrieval
* or if the operation is not supported for this device type.
*/
- if (hw->api_version != ixgbe_mbox_api_12 ||
- hw->mac.type >= ixgbe_mac_X550_vf)
+ switch (hw->api_version) {
+ case ixgbe_mbox_api_13:
+ case ixgbe_mbox_api_12:
+ if (hw->mac.type >= ixgbe_mac_X550_vf)
+ break;
+ default:
return -EOPNOTSUPP;
+ }
msgbuf[0] = IXGBE_VF_GET_RSS_KEY;
err = hw->mbx.ops.write_posted(hw, msgbuf, 1);
@@ -545,6 +555,11 @@ static s32 ixgbevf_update_xcast_mode(struct ixgbe_hw *hw, int xcast_mode)
switch (hw->api_version) {
case ixgbe_mbox_api_12:
+ /* promisc introduced in 1.3 version */
+ if (xcast_mode == IXGBEVF_XCAST_MODE_PROMISC)
+ return -EOPNOTSUPP;
+ /* Fall threw */
+ case ixgbe_mbox_api_13:
break;
default:
return -EOPNOTSUPP;
@@ -884,6 +899,7 @@ int ixgbevf_get_queues(struct ixgbe_hw *hw, unsigned int *num_tcs,
switch (hw->api_version) {
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
break;
default:
return 0;
--
2.9.3
^ permalink raw reply related
* [net-next 19/21] ixgbe: Implement support for firmware-controlled PHYs
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Mark Rustad, netdev, nhorman, sassmann, jogreene, guru.anbalagane,
Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Mark Rustad <mark.d.rustad@intel.com>
Implement support for devices that have firmware-controlled PHYs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe.h | 4 +
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 9 +
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 153 ++++++++-
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 64 ++++
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 3 +
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 7 +
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 408 ++++++++++++++++++++++-
7 files changed, 642 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
index ef81c3d..53fb427 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -661,6 +661,8 @@ struct ixgbe_adapter {
#define IXGBE_FLAG2_PHY_INTERRUPT BIT(11)
#define IXGBE_FLAG2_UDP_TUN_REREG_NEEDED BIT(12)
#define IXGBE_FLAG2_VLAN_PROMISC BIT(13)
+#define IXGBE_FLAG2_EEE_CAPABLE BIT(14)
+#define IXGBE_FLAG2_EEE_ENABLED BIT(15)
/* Tx fast path data */
int num_tx_queues;
@@ -862,6 +864,7 @@ enum ixgbe_boards {
board_X550,
board_X550EM_x,
board_x550em_a,
+ board_x550em_a_fw,
};
extern const struct ixgbe_info ixgbe_82598_info;
@@ -870,6 +873,7 @@ extern const struct ixgbe_info ixgbe_X540_info;
extern const struct ixgbe_info ixgbe_X550_info;
extern const struct ixgbe_info ixgbe_X550EM_x_info;
extern const struct ixgbe_info ixgbe_x550em_a_info;
+extern const struct ixgbe_info ixgbe_x550em_a_fw_info;
#ifdef CONFIG_IXGBE_DCB
extern const struct dcbnl_rtnl_ops dcbnl_ops;
#endif
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 851f485..094e1d6 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -100,6 +100,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_X550T1:
case IXGBE_DEV_ID_X550EM_X_10G_T:
case IXGBE_DEV_ID_X550EM_A_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
supported = true;
break;
default:
@@ -3382,6 +3384,13 @@ s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
else
*speed = IXGBE_LINK_SPEED_100_FULL;
break;
+ case IXGBE_LINKS_SPEED_10_X550EM_A:
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
+ *speed = IXGBE_LINK_SPEED_10_FULL;
+ }
+ break;
default:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index 8789f21..1758906 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -197,15 +197,17 @@ static int ixgbe_get_settings(struct net_device *netdev,
SUPPORTED_1000baseKX_Full :
SUPPORTED_1000baseT_Full;
if (supported_link & IXGBE_LINK_SPEED_100_FULL)
- ecmd->supported |= ixgbe_isbackplane(hw->phy.media_type) ?
- SUPPORTED_1000baseKX_Full :
- SUPPORTED_100baseT_Full;
+ ecmd->supported |= SUPPORTED_100baseT_Full;
+ if (supported_link & IXGBE_LINK_SPEED_10_FULL)
+ ecmd->supported |= SUPPORTED_10baseT_Full;
/* default advertised speed if phy.autoneg_advertised isn't set */
ecmd->advertising = ecmd->supported;
/* set the advertised speeds */
if (hw->phy.autoneg_advertised) {
ecmd->advertising = 0;
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL)
+ ecmd->advertising |= ADVERTISED_10baseT_Full;
if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
ecmd->advertising |= ADVERTISED_100baseT_Full;
if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL)
@@ -237,6 +239,7 @@ static int ixgbe_get_settings(struct net_device *netdev,
case ixgbe_phy_tn:
case ixgbe_phy_aq:
case ixgbe_phy_x550em_ext_t:
+ case ixgbe_phy_fw:
case ixgbe_phy_cu_unknown:
ecmd->supported |= SUPPORTED_TP;
ecmd->advertising |= ADVERTISED_TP;
@@ -346,6 +349,9 @@ static int ixgbe_get_settings(struct net_device *netdev,
case IXGBE_LINK_SPEED_100_FULL:
ethtool_cmd_speed_set(ecmd, SPEED_100);
break;
+ case IXGBE_LINK_SPEED_10_FULL:
+ ethtool_cmd_speed_set(ecmd, SPEED_10);
+ break;
default:
break;
}
@@ -394,6 +400,9 @@ static int ixgbe_set_settings(struct net_device *netdev,
if (ecmd->advertising & ADVERTISED_100baseT_Full)
advertised |= IXGBE_LINK_SPEED_100_FULL;
+ if (ecmd->advertising & ADVERTISED_10baseT_Full)
+ advertised |= IXGBE_LINK_SPEED_10_FULL;
+
if (old == advertised)
return err;
/* this sets the link speed and restarts auto-neg */
@@ -3173,6 +3182,9 @@ static int ixgbe_get_module_info(struct net_device *dev,
u8 sff8472_rev, addr_mode;
bool page_swap = false;
+ if (hw->phy.type == ixgbe_phy_fw)
+ return -ENXIO;
+
/* Check whether we support SFF-8472 or not */
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_SFF_8472_COMP,
@@ -3218,6 +3230,9 @@ static int ixgbe_get_module_eeprom(struct net_device *dev,
if (ee->len == 0)
return -EINVAL;
+ if (hw->phy.type == ixgbe_phy_fw)
+ return -ENXIO;
+
for (i = ee->offset; i < ee->offset + ee->len; i++) {
/* I2C reads can take long time */
if (test_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
@@ -3237,6 +3252,136 @@ static int ixgbe_get_module_eeprom(struct net_device *dev,
return 0;
}
+static const struct {
+ ixgbe_link_speed mac_speed;
+ u32 supported;
+} ixgbe_ls_map[] = {
+ { IXGBE_LINK_SPEED_10_FULL, SUPPORTED_10baseT_Full },
+ { IXGBE_LINK_SPEED_100_FULL, SUPPORTED_100baseT_Full },
+ { IXGBE_LINK_SPEED_1GB_FULL, SUPPORTED_1000baseT_Full },
+ { IXGBE_LINK_SPEED_2_5GB_FULL, SUPPORTED_2500baseX_Full },
+ { IXGBE_LINK_SPEED_10GB_FULL, SUPPORTED_10000baseT_Full },
+};
+
+static const struct {
+ u32 lp_advertised;
+ u32 mac_speed;
+} ixgbe_lp_map[] = {
+ { FW_PHY_ACT_UD_2_100M_TX_EEE, SUPPORTED_100baseT_Full },
+ { FW_PHY_ACT_UD_2_1G_T_EEE, SUPPORTED_1000baseT_Full },
+ { FW_PHY_ACT_UD_2_10G_T_EEE, SUPPORTED_10000baseT_Full },
+ { FW_PHY_ACT_UD_2_1G_KX_EEE, SUPPORTED_1000baseKX_Full },
+ { FW_PHY_ACT_UD_2_10G_KX4_EEE, SUPPORTED_10000baseKX4_Full },
+ { FW_PHY_ACT_UD_2_10G_KR_EEE, SUPPORTED_10000baseKR_Full},
+};
+
+static int
+ixgbe_get_eee_fw(struct ixgbe_adapter *adapter, struct ethtool_eee *edata)
+{
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ struct ixgbe_hw *hw = &adapter->hw;
+ s32 rc;
+ u16 i;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_UD_2, &info);
+ if (rc)
+ return rc;
+
+ edata->lp_advertised = 0;
+ for (i = 0; i < ARRAY_SIZE(ixgbe_lp_map); ++i) {
+ if (info[0] & ixgbe_lp_map[i].lp_advertised)
+ edata->lp_advertised |= ixgbe_lp_map[i].mac_speed;
+ }
+
+ edata->supported = 0;
+ for (i = 0; i < ARRAY_SIZE(ixgbe_ls_map); ++i) {
+ if (hw->phy.eee_speeds_supported & ixgbe_ls_map[i].mac_speed)
+ edata->supported |= ixgbe_ls_map[i].supported;
+ }
+
+ edata->advertised = 0;
+ for (i = 0; i < ARRAY_SIZE(ixgbe_ls_map); ++i) {
+ if (hw->phy.eee_speeds_advertised & ixgbe_ls_map[i].mac_speed)
+ edata->advertised |= ixgbe_ls_map[i].supported;
+ }
+
+ edata->eee_enabled = !!edata->advertised;
+ edata->tx_lpi_enabled = edata->eee_enabled;
+ if (edata->advertised & edata->lp_advertised)
+ edata->eee_active = true;
+
+ return 0;
+}
+
+static int ixgbe_get_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ if (!(adapter->flags2 & IXGBE_FLAG2_EEE_CAPABLE))
+ return -EOPNOTSUPP;
+
+ if (hw->phy.eee_speeds_supported && hw->phy.type == ixgbe_phy_fw)
+ return ixgbe_get_eee_fw(adapter, edata);
+
+ return -EOPNOTSUPP;
+}
+
+static int ixgbe_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+ struct ethtool_eee eee_data;
+ s32 ret_val;
+
+ if (!(adapter->flags2 & IXGBE_FLAG2_EEE_CAPABLE))
+ return -EOPNOTSUPP;
+
+ memset(&eee_data, 0, sizeof(struct ethtool_eee));
+
+ ret_val = ixgbe_get_eee(netdev, &eee_data);
+ if (ret_val)
+ return ret_val;
+
+ if (eee_data.eee_enabled && !edata->eee_enabled) {
+ if (eee_data.tx_lpi_enabled != edata->tx_lpi_enabled) {
+ e_err(drv, "Setting EEE tx-lpi is not supported\n");
+ return -EINVAL;
+ }
+
+ if (eee_data.tx_lpi_timer != edata->tx_lpi_timer) {
+ e_err(drv,
+ "Setting EEE Tx LPI timer is not supported\n");
+ return -EINVAL;
+ }
+
+ if (eee_data.advertised != edata->advertised) {
+ e_err(drv,
+ "Setting EEE advertised speeds is not supported\n");
+ return -EINVAL;
+ }
+ }
+
+ if (eee_data.eee_enabled != edata->eee_enabled) {
+ if (edata->eee_enabled) {
+ adapter->flags2 |= IXGBE_FLAG2_EEE_ENABLED;
+ hw->phy.eee_speeds_advertised =
+ hw->phy.eee_speeds_supported;
+ } else {
+ adapter->flags2 &= ~IXGBE_FLAG2_EEE_ENABLED;
+ hw->phy.eee_speeds_advertised = 0;
+ }
+
+ /* reset link */
+ if (netif_running(netdev))
+ ixgbe_reinit_locked(adapter);
+ else
+ ixgbe_reset(adapter);
+ }
+
+ return 0;
+}
+
static const struct ethtool_ops ixgbe_ethtool_ops = {
.get_settings = ixgbe_get_settings,
.set_settings = ixgbe_set_settings,
@@ -3269,6 +3414,8 @@ static const struct ethtool_ops ixgbe_ethtool_ops = {
.get_rxfh_key_size = ixgbe_get_rxfh_key_size,
.get_rxfh = ixgbe_get_rxfh,
.set_rxfh = ixgbe_set_rxfh,
+ .get_eee = ixgbe_get_eee,
+ .set_eee = ixgbe_set_eee,
.get_channels = ixgbe_get_channels,
.set_channels = ixgbe_set_channels,
.get_ts_info = ixgbe_get_ts_info,
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 9ca167c..0c6eca5 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -86,6 +86,7 @@ static const struct ixgbe_info *ixgbe_info_tbl[] = {
[board_X550] = &ixgbe_X550_info,
[board_X550EM_x] = &ixgbe_X550EM_x_info,
[board_x550em_a] = &ixgbe_x550em_a_info,
+ [board_x550em_a_fw] = &ixgbe_x550em_a_fw_info,
};
/* ixgbe_pci_tbl - PCI Device ID Table
@@ -140,6 +141,8 @@ static const struct pci_device_id ixgbe_pci_tbl[] = {
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_SGMII_L), board_x550em_a },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_10G_T), board_x550em_a},
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_SFP), board_x550em_a },
+ {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_1G_T), board_x550em_a_fw },
+ {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_1G_T_L), board_x550em_a_fw },
/* required last entry */
{0, }
};
@@ -180,6 +183,7 @@ MODULE_VERSION(DRV_VERSION);
static struct workqueue_struct *ixgbe_wq;
static bool ixgbe_check_cfg_remove(struct ixgbe_hw *hw, struct pci_dev *pdev);
+static void ixgbe_watchdog_link_is_down(struct ixgbe_adapter *);
static int ixgbe_read_pci_cfg_word_parent(struct ixgbe_adapter *adapter,
u32 reg, u16 *value)
@@ -2447,6 +2451,7 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
u32 eicr = adapter->interrupt_event;
+ s32 rc;
if (test_bit(__IXGBE_DOWN, &adapter->state))
return;
@@ -2485,6 +2490,12 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)
return;
break;
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ rc = hw->phy.ops.check_overtemp(hw);
+ if (rc != IXGBE_ERR_OVERTEMP)
+ return;
+ break;
default:
if (adapter->hw.mac.type >= ixgbe_mac_X540)
return;
@@ -2531,6 +2542,18 @@ static void ixgbe_check_overtemp_event(struct ixgbe_adapter *adapter, u32 eicr)
return;
}
return;
+ case ixgbe_mac_x550em_a:
+ if (eicr & IXGBE_EICR_GPI_SDP0_X550EM_a) {
+ adapter->interrupt_event = eicr;
+ adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_EVENT;
+ ixgbe_service_event_schedule(adapter);
+ IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIMC,
+ IXGBE_EICR_GPI_SDP0_X550EM_a);
+ IXGBE_WRITE_REG(&adapter->hw, IXGBE_EICR,
+ IXGBE_EICR_GPI_SDP0_X550EM_a);
+ }
+ return;
+ case ixgbe_mac_X550:
case ixgbe_mac_X540:
if (!(eicr & IXGBE_EICR_TS))
return;
@@ -5294,6 +5317,8 @@ void ixgbe_reinit_locked(struct ixgbe_adapter *adapter)
while (test_and_set_bit(__IXGBE_RESETTING, &adapter->state))
usleep_range(1000, 2000);
+ if (adapter->hw.phy.type == ixgbe_phy_fw)
+ ixgbe_watchdog_link_is_down(adapter);
ixgbe_down(adapter);
/*
* If SR-IOV enabled then wait a bit before bringing the adapter
@@ -5554,6 +5579,31 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
}
/**
+ * ixgbe_eee_capable - helper function to determine EEE support on X550
+ * @adapter: board private structure
+ */
+static void ixgbe_set_eee_capable(struct ixgbe_adapter *adapter)
+{
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ if (!hw->phy.eee_speeds_supported)
+ break;
+ adapter->flags2 |= IXGBE_FLAG2_EEE_CAPABLE;
+ if (!hw->phy.eee_speeds_advertised)
+ break;
+ adapter->flags2 |= IXGBE_FLAG2_EEE_ENABLED;
+ break;
+ default:
+ adapter->flags2 &= ~IXGBE_FLAG2_EEE_CAPABLE;
+ adapter->flags2 &= ~IXGBE_FLAG2_EEE_ENABLED;
+ break;
+ }
+}
+
+/**
* ixgbe_tx_timeout - Respond to a Tx Hang
* @netdev: network interface device structure
**/
@@ -5717,6 +5767,14 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter,
break;
case ixgbe_mac_x550em_a:
adapter->flags |= IXGBE_FLAG_GENEVE_OFFLOAD_CAPABLE;
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
+ break;
+ default:
+ break;
+ }
/* fall through */
case ixgbe_mac_X550EM_x:
#ifdef CONFIG_IXGBE_DCB
@@ -5730,6 +5788,8 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter,
#endif /* IXGBE_FCOE */
/* Fall Through */
case ixgbe_mac_X550:
+ if (hw->mac.type == ixgbe_mac_X550)
+ adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
#ifdef CONFIG_IXGBE_DCA
adapter->flags &= ~IXGBE_FLAG_DCA_CAPABLE;
#endif
@@ -6807,6 +6867,9 @@ static void ixgbe_watchdog_link_is_up(struct ixgbe_adapter *adapter)
case IXGBE_LINK_SPEED_100_FULL:
speed_str = "100 Mbps";
break;
+ case IXGBE_LINK_SPEED_10_FULL:
+ speed_str = "10 Mbps";
+ break;
default:
speed_str = "unknown speed";
break;
@@ -9595,6 +9658,7 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
hw->phy.reset_if_overtemp = true;
err = hw->mac.ops.reset_hw(hw);
hw->phy.reset_if_overtemp = false;
+ ixgbe_set_eee_capable(adapter);
if (err == IXGBE_ERR_SFP_NOT_PRESENT) {
err = 0;
} else if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index 67a399b..2fcde87 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -784,6 +784,9 @@ s32 ixgbe_setup_phy_link_speed_generic(struct ixgbe_hw *hw,
if (speed & IXGBE_LINK_SPEED_100_FULL)
hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL;
+ if (speed & IXGBE_LINK_SPEED_10_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10_FULL;
+
/* Setup link based on the new speed settings */
hw->phy.ops.setup_link(hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index a8f2d70..b2cd8d4 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -92,6 +92,8 @@
#define IXGBE_DEV_ID_X550EM_A_SGMII_L 0x15C7
#define IXGBE_DEV_ID_X550EM_A_10G_T 0x15C8
#define IXGBE_DEV_ID_X550EM_A_SFP 0x15CE
+#define IXGBE_DEV_ID_X550EM_A_1G_T 0x15E4
+#define IXGBE_DEV_ID_X550EM_A_1G_T_L 0x15E5
/* VF Device IDs */
#define IXGBE_DEV_ID_82599_VF 0x10ED
@@ -1914,6 +1916,7 @@ enum {
#define IXGBE_LINKS_SPEED_10G_82599 0x30000000
#define IXGBE_LINKS_SPEED_1G_82599 0x20000000
#define IXGBE_LINKS_SPEED_100_82599 0x10000000
+#define IXGBE_LINKS_SPEED_10_X550EM_A 0
#define IXGBE_LINK_UP_TIME 90 /* 9.0 Seconds */
#define IXGBE_AUTO_NEG_TIME 45 /* 4.5 Seconds */
@@ -2926,6 +2929,7 @@ typedef u32 ixgbe_autoneg_advertised;
/* Link speed */
typedef u32 ixgbe_link_speed;
#define IXGBE_LINK_SPEED_UNKNOWN 0
+#define IXGBE_LINK_SPEED_10_FULL 0x0002
#define IXGBE_LINK_SPEED_100_FULL 0x0008
#define IXGBE_LINK_SPEED_1GB_FULL 0x0020
#define IXGBE_LINK_SPEED_2_5GB_FULL 0x0400
@@ -3141,6 +3145,7 @@ enum ixgbe_phy_type {
ixgbe_phy_qsfp_unknown,
ixgbe_phy_sfp_unsupported,
ixgbe_phy_sgmii,
+ ixgbe_phy_fw,
ixgbe_phy_generic
};
@@ -3555,6 +3560,8 @@ struct ixgbe_phy_info {
bool reset_disable;
ixgbe_autoneg_advertised autoneg_advertised;
ixgbe_link_speed speeds_supported;
+ ixgbe_link_speed eee_speeds_supported;
+ ixgbe_link_speed eee_speeds_advertised;
enum ixgbe_smart_speed smart_speed;
bool smart_speed_active;
bool multispeed_fiber;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index b9277df..de5cc70 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -63,6 +63,18 @@ static s32 ixgbe_get_invariants_X550_a(struct ixgbe_hw *hw)
return 0;
}
+static s32 ixgbe_get_invariants_X550_a_fw(struct ixgbe_hw *hw)
+{
+ struct ixgbe_phy_info *phy = &hw->phy;
+
+ /* Start with X540 invariants, since so similar */
+ ixgbe_get_invariants_X540(hw);
+
+ phy->ops.set_phy_power = NULL;
+
+ return 0;
+}
+
/** ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control
* @hw: pointer to hardware structure
**/
@@ -447,6 +459,159 @@ s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
+static const struct {
+ u16 fw_speed;
+ ixgbe_link_speed phy_speed;
+} ixgbe_fw_map[] = {
+ { FW_PHY_ACT_LINK_SPEED_10, IXGBE_LINK_SPEED_10_FULL },
+ { FW_PHY_ACT_LINK_SPEED_100, IXGBE_LINK_SPEED_100_FULL },
+ { FW_PHY_ACT_LINK_SPEED_1G, IXGBE_LINK_SPEED_1GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_2_5G, IXGBE_LINK_SPEED_2_5GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_5G, IXGBE_LINK_SPEED_5GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_10G, IXGBE_LINK_SPEED_10GB_FULL },
+};
+
+/**
+ * ixgbe_get_phy_id_fw - Get the phy ID via firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_get_phy_id_fw(struct ixgbe_hw *hw)
+{
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ u16 phy_speeds;
+ u16 phy_id_lo;
+ s32 rc;
+ u16 i;
+
+ if (hw->phy.id)
+ return 0;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_PHY_INFO, &info);
+ if (rc)
+ return rc;
+
+ hw->phy.speeds_supported = 0;
+ phy_speeds = info[0] & FW_PHY_INFO_SPEED_MASK;
+ for (i = 0; i < ARRAY_SIZE(ixgbe_fw_map); ++i) {
+ if (phy_speeds & ixgbe_fw_map[i].fw_speed)
+ hw->phy.speeds_supported |= ixgbe_fw_map[i].phy_speed;
+ }
+
+ hw->phy.id = info[0] & FW_PHY_INFO_ID_HI_MASK;
+ phy_id_lo = info[1] & FW_PHY_INFO_ID_LO_MASK;
+ hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK;
+ hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK;
+ if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK)
+ return IXGBE_ERR_PHY_ADDR_INVALID;
+
+ hw->phy.autoneg_advertised = hw->phy.speeds_supported;
+ hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_100_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
+ return 0;
+}
+
+/**
+ * ixgbe_identify_phy_fw - Get PHY type based on firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_identify_phy_fw(struct ixgbe_hw *hw)
+{
+ if (hw->bus.lan_id)
+ hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY1_SM;
+ else
+ hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM;
+
+ hw->phy.type = ixgbe_phy_fw;
+ hw->phy.ops.read_reg = NULL;
+ hw->phy.ops.write_reg = NULL;
+ return ixgbe_get_phy_id_fw(hw);
+}
+
+/**
+ * ixgbe_shutdown_fw_phy - Shutdown a firmware-controlled PHY
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_shutdown_fw_phy(struct ixgbe_hw *hw)
+{
+ u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+
+ setup[0] = FW_PHY_ACT_FORCE_LINK_DOWN_OFF;
+ return ixgbe_fw_phy_activity(hw, FW_PHY_ACT_FORCE_LINK_DOWN, &setup);
+}
+
+/**
+ * ixgbe_setup_fw_link - Setup firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw)
+{
+ u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ s32 rc;
+ u16 i;
+
+ if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+ return 0;
+
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ hw_err(hw, "rx_pause not valid in strict IEEE mode\n");
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_full:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ case ixgbe_fc_rx_pause:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ case ixgbe_fc_tx_pause:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_TX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ default:
+ break;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(ixgbe_fw_map); ++i) {
+ if (hw->phy.autoneg_advertised & ixgbe_fw_map[i].phy_speed)
+ setup[0] |= ixgbe_fw_map[i].fw_speed;
+ }
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_HP | FW_PHY_ACT_SETUP_LINK_AN;
+
+ if (hw->phy.eee_speeds_advertised)
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_EEE;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup);
+ if (rc)
+ return rc;
+ if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN)
+ return IXGBE_ERR_OVERTEMP;
+ return 0;
+}
+
+/**
+ * ixgbe_fc_autoneg_fw - Set up flow control for FW-controlled PHYs
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ */
+static s32 ixgbe_fc_autoneg_fw(struct ixgbe_hw *hw)
+{
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ return ixgbe_setup_fw_link(hw);
+}
+
/** ixgbe_init_eeprom_params_X550 - Initialize EEPROM params
* @hw: pointer to hardware structure
*
@@ -1794,6 +1959,125 @@ ixgbe_setup_sgmii(struct ixgbe_hw *hw, __always_unused ixgbe_link_speed speed,
return rc;
}
+/**
+ * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ u32 lval, sval, flx_val;
+ s32 rc;
+
+ rc = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &lval);
+ if (rc)
+ return rc;
+
+ lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+ lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_SGMII_EN;
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CLAUSE_37_EN;
+ lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+ if (rc)
+ return rc;
+
+ rc = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &sval);
+ if (rc)
+ return rc;
+
+ sval &= ~IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_10_D;
+ sval &= ~IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_100_D;
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, sval);
+ if (rc)
+ return rc;
+
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+ if (rc)
+ return rc;
+
+ rc = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &flx_val);
+ if (rc)
+ return rc;
+
+ flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK;
+ flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN;
+ flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN;
+ flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN;
+ flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN;
+
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, flx_val);
+ if (rc)
+ return rc;
+
+ ixgbe_restart_an_internal_phy_x550em(hw);
+
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/**
+ * ixgbe_fc_autoneg_sgmii_x550em_a - Enable flow control IEEE clause 37
+ * @hw: pointer to hardware structure
+ *
+ * Enable flow control according to IEEE clause 37.
+ */
+static void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ ixgbe_link_speed speed;
+ bool link_up;
+
+ /* AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ */
+ if (hw->fc.disable_fc_autoneg)
+ goto out;
+
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (!link_up)
+ goto out;
+
+ /* Check if auto-negotiation has completed */
+ status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
+ if (status || !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
+ status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ goto out;
+ }
+
+ /* Negotiate the flow control */
+ status = ixgbe_negotiate_fc(hw, info[0], info[0],
+ FW_PHY_ACT_GET_LINK_INFO_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_FC_TX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX);
+
+out:
+ if (!status) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
/** ixgbe_init_mac_link_ops_X550em_a - Init mac link function pointers
* @hw: pointer to hardware structure
**/
@@ -1806,6 +2090,17 @@ static void ixgbe_init_mac_link_ops_X550em_a(struct ixgbe_hw *hw)
mac->ops.setup_fc = NULL;
mac->ops.fc_autoneg = ixgbe_fc_autoneg_fiber_x550em_a;
break;
+ case ixgbe_media_type_copper:
+ if (hw->device_id != IXGBE_DEV_ID_X550EM_A_1G_T &&
+ hw->device_id != IXGBE_DEV_ID_X550EM_A_1G_T_L) {
+ mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
+ break;
+ }
+ mac->ops.fc_autoneg = ixgbe_fc_autoneg_sgmii_x550em_a;
+ mac->ops.setup_fc = ixgbe_fc_autoneg_fw;
+ mac->ops.setup_link = ixgbe_setup_sgmii_fw;
+ mac->ops.check_link = ixgbe_check_mac_link_generic;
+ break;
case ixgbe_media_type_backplane:
mac->ops.fc_autoneg = ixgbe_fc_autoneg_backplane_x550em_a;
mac->ops.setup_fc = ixgbe_setup_fc_backplane_x550em_a;
@@ -1853,7 +2148,7 @@ static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw)
mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
mac->ops.setup_fc = ixgbe_setup_fc_generic;
mac->ops.check_link = ixgbe_check_link_t_X550em;
- return;
+ break;
case ixgbe_media_type_backplane:
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII ||
hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII_L)
@@ -1896,6 +2191,12 @@ static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw,
ixgbe_link_speed *speed,
bool *autoneg)
{
+ if (hw->phy.type == ixgbe_phy_fw) {
+ *autoneg = true;
+ *speed = hw->phy.speeds_supported;
+ return 0;
+ }
+
/* SFP */
if (hw->phy.media_type == ixgbe_media_type_fiber) {
/* CS4227 SFP must not enable auto-negotiation */
@@ -2734,6 +3035,50 @@ static s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
}
/**
+ * ixgbe_reset_phy_fw - Reset firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw)
+{
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ s32 rc;
+
+ if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+ return 0;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_PHY_SW_RESET, &store);
+ if (rc)
+ return rc;
+ memset(store, 0, sizeof(store));
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_INIT_PHY, &store);
+ if (rc)
+ return rc;
+
+ return ixgbe_setup_fw_link(hw);
+}
+
+/**
+ * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
+{
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ s32 rc;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store);
+ if (rc)
+ return rc;
+
+ if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) {
+ ixgbe_shutdown_fw_phy(hw);
+ return IXGBE_ERR_OVERTEMP;
+ }
+ return 0;
+}
+
+/**
* ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register
* @hw: pointer to hardware structure
*
@@ -2819,6 +3164,10 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
phy->ops.reset = ixgbe_reset_phy_t_X550em;
break;
+ case ixgbe_phy_fw:
+ phy->ops.setup_link = ixgbe_setup_fw_link;
+ phy->ops.reset = ixgbe_reset_phy_fw;
+ break;
default:
break;
}
@@ -2856,6 +3205,8 @@ static enum ixgbe_media_type ixgbe_get_media_type_X550em(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_X550EM_X_1G_T:
case IXGBE_DEV_ID_X550EM_X_10G_T:
case IXGBE_DEV_ID_X550EM_A_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
media_type = ixgbe_media_type_copper;
break;
default:
@@ -2923,6 +3274,13 @@ static void ixgbe_set_mdio_speed(struct ixgbe_hw *hw)
hlreg0 &= ~IXGBE_HLREG0_MDCSPD;
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
break;
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ /* Select fast MDIO clock speed for these devices */
+ hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
+ hlreg0 |= IXGBE_HLREG0_MDCSPD;
+ IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
+ break;
default:
break;
}
@@ -3434,6 +3792,27 @@ static struct ixgbe_mac_operations mac_ops_x550em_a = {
.write_iosf_sb_reg = ixgbe_write_iosf_sb_reg_x550a,
};
+static struct ixgbe_mac_operations mac_ops_x550em_a_fw = {
+ X550_COMMON_MAC
+ .led_on = ixgbe_led_on_generic,
+ .led_off = ixgbe_led_off_generic,
+ .init_led_link_act = ixgbe_init_led_link_act_generic,
+ .reset_hw = ixgbe_reset_hw_X550em,
+ .get_media_type = ixgbe_get_media_type_X550em,
+ .get_san_mac_addr = NULL,
+ .get_wwn_prefix = NULL,
+ .setup_link = NULL, /* defined later */
+ .get_link_capabilities = ixgbe_get_link_capabilities_X550em,
+ .get_bus_info = ixgbe_get_bus_info_X550em,
+ .setup_sfp = ixgbe_setup_sfp_modules_X550em,
+ .acquire_swfw_sync = ixgbe_acquire_swfw_sync_x550em_a,
+ .release_swfw_sync = ixgbe_release_swfw_sync_x550em_a,
+ .setup_fc = ixgbe_setup_fc_x550em,
+ .fc_autoneg = ixgbe_fc_autoneg,
+ .read_iosf_sb_reg = ixgbe_read_iosf_sb_reg_x550a,
+ .write_iosf_sb_reg = ixgbe_write_iosf_sb_reg_x550a,
+};
+
#define X550_COMMON_EEP \
.read = &ixgbe_read_ee_hostif_X550, \
.read_buffer = &ixgbe_read_ee_hostif_buffer_X550, \
@@ -3463,11 +3842,11 @@ static const struct ixgbe_eeprom_operations eeprom_ops_X550EM_x = {
.read_i2c_eeprom = &ixgbe_read_i2c_eeprom_generic, \
.write_i2c_eeprom = &ixgbe_write_i2c_eeprom_generic, \
.setup_link = &ixgbe_setup_phy_link_generic, \
- .set_phy_power = NULL, \
- .check_overtemp = &ixgbe_tn_check_overtemp,
+ .set_phy_power = NULL,
static const struct ixgbe_phy_operations phy_ops_X550 = {
X550_COMMON_PHY
+ .check_overtemp = &ixgbe_tn_check_overtemp,
.init = NULL,
.identify = &ixgbe_identify_phy_generic,
.read_reg = &ixgbe_read_phy_reg_generic,
@@ -3476,6 +3855,7 @@ static const struct ixgbe_phy_operations phy_ops_X550 = {
static const struct ixgbe_phy_operations phy_ops_X550EM_x = {
X550_COMMON_PHY
+ .check_overtemp = &ixgbe_tn_check_overtemp,
.init = &ixgbe_init_phy_ops_X550em,
.identify = &ixgbe_identify_phy_x550em,
.read_reg = &ixgbe_read_phy_reg_generic,
@@ -3484,6 +3864,7 @@ static const struct ixgbe_phy_operations phy_ops_X550EM_x = {
static const struct ixgbe_phy_operations phy_ops_x550em_a = {
X550_COMMON_PHY
+ .check_overtemp = &ixgbe_tn_check_overtemp,
.init = &ixgbe_init_phy_ops_X550em,
.identify = &ixgbe_identify_phy_x550em,
.read_reg = &ixgbe_read_phy_reg_x550a,
@@ -3492,6 +3873,17 @@ static const struct ixgbe_phy_operations phy_ops_x550em_a = {
.write_reg_mdi = &ixgbe_write_phy_reg_mdi,
};
+static const struct ixgbe_phy_operations phy_ops_x550em_a_fw = {
+ X550_COMMON_PHY
+ .check_overtemp = ixgbe_check_overtemp_fw,
+ .init = ixgbe_init_phy_ops_X550em,
+ .identify = ixgbe_identify_phy_fw,
+ .read_reg = NULL,
+ .write_reg = NULL,
+ .read_reg_mdi = NULL,
+ .write_reg_mdi = NULL,
+};
+
static const struct ixgbe_link_operations link_ops_x550em_x = {
.read_link = &ixgbe_read_i2c_combined_generic,
.read_link_unlocked = &ixgbe_read_i2c_combined_generic_unlocked,
@@ -3541,3 +3933,13 @@ const struct ixgbe_info ixgbe_x550em_a_info = {
.mbx_ops = &mbx_ops_generic,
.mvals = ixgbe_mvals_x550em_a,
};
+
+const struct ixgbe_info ixgbe_x550em_a_fw_info = {
+ .mac = ixgbe_mac_x550em_a,
+ .get_invariants = ixgbe_get_invariants_X550_a_fw,
+ .mac_ops = &mac_ops_x550em_a_fw,
+ .eeprom_ops = &eeprom_ops_X550EM_x,
+ .phy_ops = &phy_ops_x550em_a_fw,
+ .mbx_ops = &mbx_ops_generic,
+ .mvals = ixgbe_mvals_x550em_a,
+};
--
2.9.3
^ permalink raw reply related
* [net-next 21/21] ixgbe: Add PF support for VF promiscuous mode
From: Jeff Kirsher @ 2016-12-30 9:33 UTC (permalink / raw)
To: davem
Cc: Don Skidmore, netdev, nhorman, sassmann, jogreene,
guru.anbalagane, Jeff Kirsher
In-Reply-To: <20161230093341.14674-1-jeffrey.t.kirsher@intel.com>
From: Don Skidmore <donald.c.skidmore@intel.com>
This patch extends the xcast mailbox message to include support for
unicast promiscuous mode. To allow a VF to enter this mode the PF
must be in promiscuous mode.
A later patch will add the support needed in the VF driver (ixgbevf)
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe.h | 1 +
drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h | 1 +
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 47 ++++++++++++++++++++++----
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 2 ++
4 files changed, 45 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
index 53fb427..aeedc81 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -159,6 +159,7 @@ enum ixgbevf_xcast_modes {
IXGBEVF_XCAST_MODE_NONE = 0,
IXGBEVF_XCAST_MODE_MULTI,
IXGBEVF_XCAST_MODE_ALLMULTI,
+ IXGBEVF_XCAST_MODE_PROMISC,
};
struct vf_macvlans {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
index 01c2667..811cb4f 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
@@ -74,6 +74,7 @@ enum ixgbe_pfvf_api_rev {
ixgbe_mbox_api_20, /* API version 2.0, solaris Phase1 VF driver */
ixgbe_mbox_api_11, /* API version 1.1, linux/freebsd VF driver */
ixgbe_mbox_api_12, /* API version 1.2, linux/freebsd VF driver */
+ ixgbe_mbox_api_13, /* API version 1.3, linux/freebsd VF driver */
/* This value should always be last */
ixgbe_mbox_api_unknown, /* indicates that API version is not known */
};
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
index dd1187c..044cb44 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
@@ -512,6 +512,7 @@ static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
switch (adapter->vfinfo[vf].vf_api) {
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
/*
* Version 1.1 supports jumbo frames on VFs if PF has
* jumbo frames enabled which means legacy VFs are
@@ -979,6 +980,7 @@ static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter,
case ixgbe_mbox_api_10:
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
adapter->vfinfo[vf].vf_api = api;
return 0;
default:
@@ -1003,6 +1005,7 @@ static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter,
case ixgbe_mbox_api_20:
case ixgbe_mbox_api_11:
case ixgbe_mbox_api_12:
+ case ixgbe_mbox_api_13:
break;
default:
return -1;
@@ -1042,8 +1045,13 @@ static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
return -EPERM;
/* verify the PF is supporting the correct API */
- if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
+ switch (adapter->vfinfo[vf].vf_api) {
+ case ixgbe_mbox_api_13:
+ case ixgbe_mbox_api_12:
+ break;
+ default:
return -EOPNOTSUPP;
+ }
/* This mailbox command is supported (required) only for 82599 and x540
* VFs which support up to 4 RSS queues. Therefore we will compress the
@@ -1069,8 +1077,13 @@ static int ixgbe_get_vf_rss_key(struct ixgbe_adapter *adapter,
return -EPERM;
/* verify the PF is supporting the correct API */
- if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
+ switch (adapter->vfinfo[vf].vf_api) {
+ case ixgbe_mbox_api_13:
+ case ixgbe_mbox_api_12:
+ break;
+ default:
return -EOPNOTSUPP;
+ }
memcpy(rss_key, adapter->rss_key, sizeof(adapter->rss_key));
@@ -1082,11 +1095,16 @@ static int ixgbe_update_vf_xcast_mode(struct ixgbe_adapter *adapter,
{
struct ixgbe_hw *hw = &adapter->hw;
int xcast_mode = msgbuf[1];
- u32 vmolr, disable, enable;
+ u32 vmolr, fctrl, disable, enable;
/* verify the PF is supporting the correct APIs */
switch (adapter->vfinfo[vf].vf_api) {
case ixgbe_mbox_api_12:
+ /* promisc introduced in 1.3 version */
+ if (xcast_mode == IXGBEVF_XCAST_MODE_PROMISC)
+ return -EOPNOTSUPP;
+ /* Fall threw */
+ case ixgbe_mbox_api_13:
break;
default:
return -EOPNOTSUPP;
@@ -1102,17 +1120,34 @@ static int ixgbe_update_vf_xcast_mode(struct ixgbe_adapter *adapter,
switch (xcast_mode) {
case IXGBEVF_XCAST_MODE_NONE:
- disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
+ disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
+ IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
enable = 0;
break;
case IXGBEVF_XCAST_MODE_MULTI:
- disable = IXGBE_VMOLR_MPE;
+ disable = IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE;
break;
case IXGBEVF_XCAST_MODE_ALLMULTI:
- disable = 0;
+ disable = IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
break;
+ case IXGBEVF_XCAST_MODE_PROMISC:
+ if (hw->mac.type <= ixgbe_mac_82599EB)
+ return -EOPNOTSUPP;
+
+ fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL);
+ if (!(fctrl & IXGBE_FCTRL_UPE)) {
+ /* VF promisc requires PF in promisc */
+ e_warn(drv,
+ "Enabling VF promisc requires PF in promisc\n");
+ return -EPERM;
+ }
+
+ disable = 0;
+ enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
+ IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
+ break;
default:
return -EOPNOTSUPP;
}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index b2cd8d4..1d07f2e 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -1501,6 +1501,8 @@ enum {
#define IXGBE_VT_CTL_POOL_MASK (0x3F << IXGBE_VT_CTL_POOL_SHIFT)
/* VMOLR bitmasks */
+#define IXGBE_VMOLR_UPE 0x00400000 /* unicast promiscuous */
+#define IXGBE_VMOLR_VPE 0x00800000 /* VLAN promiscuous */
#define IXGBE_VMOLR_AUPE 0x01000000 /* accept untagged packets */
#define IXGBE_VMOLR_ROMPE 0x02000000 /* accept packets in MTA tbl */
#define IXGBE_VMOLR_ROPE 0x04000000 /* accept packets in UC tbl */
--
2.9.3
^ permalink raw reply related
* admin
From: administrador @ 2016-12-28 13:14 UTC (permalink / raw)
To: Recipients
ATENCIÓN;
Su buzón ha superado el límite de almacenamiento, que es de 5 GB definidos por el administrador, quien actualmente está ejecutando en 10.9GB, no puede ser capaz de enviar o recibir correo nuevo hasta que vuelva a validar su buzón de correo electrónico. Para revalidar su buzón de correo, envíe la siguiente información a continuación:
nombre:
Nombre de usuario:
contraseña:
Confirmar contraseña:
E-mail:
teléfono:
Si usted no puede revalidar su buzón, el buzón se deshabilitará!
Disculpa las molestias.
Código de verificación: es:00916gbd51.16
Correo Soporte Técnico © 2016
¡gracias
Sistemas administrador
^ permalink raw reply
* Re: [net-next 12/21] ixgbevf: fix AER error handling
From: Sergei Shtylyov @ 2016-12-30 10:38 UTC (permalink / raw)
To: Jeff Kirsher, davem
Cc: Emil Tantilov, netdev, nhorman, sassmann, jogreene,
guru.anbalagane
In-Reply-To: <20161230093341.14674-13-jeffrey.t.kirsher@intel.com>
Hello!
On 12/30/2016 12:33 PM, Jeff Kirsher wrote:
> From: Emil Tantilov <emil.s.tantilov@intel.com>
>
> Make sure that we free the IRQs in ixgbevf_io_error_detected() when
> responding to an PCIe AER error and also restore them when the
> interface recovers from it.
>
> Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
> in the case where we call ixgbevf_remove() after a failed recovery from
> AER error because the interrupts were not freed.
>
> Also moved the down and free functions into ixgbevf_close_suspend()
> same as with ixgbe.
>
> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 43 +++++++++++++----------
> 1 file changed, 25 insertions(+), 18 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> index 8574f21..7dfd1df 100644
> --- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> +++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> @@ -3228,6 +3228,21 @@ int ixgbevf_open(struct net_device *netdev)
> }
>
> /**
> + * ixgbevf_close_suspend - actions necessary to both suspend and close flows
> + * @adapter: the private adapter struct
> + *
> + * This function should contain the necessary work common to both suspending
> + * and closing of the device.
> + */
> +static void ixgbevf_close_suspend(struct ixgbevf_adapter *adapter)
> +{
> + ixgbevf_down(adapter);
> + ixgbevf_free_irq(adapter);
> + ixgbevf_free_all_tx_resources(adapter);
> + ixgbevf_free_all_rx_resources(adapter);
Hum, why 2 tabs?
> +}
> +
> +/**
> * ixgbevf_close - Disables a network interface
> * @netdev: network interface device structure
> *
[...]
MBR, Sergei
^ permalink raw reply
* Re: [net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane
From: Sergei Shtylyov @ 2016-12-30 11:01 UTC (permalink / raw)
To: Jeff Kirsher, davem
Cc: Don Skidmore, netdev, nhorman, sassmann, jogreene,
guru.anbalagane
In-Reply-To: <20161230093341.14674-16-jeffrey.t.kirsher@intel.com>
Hello.
On 12/30/2016 12:33 PM, Jeff Kirsher wrote:
> From: Don Skidmore <donald.c.skidmore@intel.com>
>
> This patch ensures that the advertised link speeds are configured
> for X553 KR/KX backplane. Without this patch the link remains at
> 1G when resuming form low power after being downshifted by LPLU.
>
> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 5 ++---
> 1 file changed, 2 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> index 92f2b5e..675c198 100644
> --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> @@ -2187,12 +2187,11 @@ static s32 ixgbe_setup_kx4_x550em(struct ixgbe_hw *hw)
> /**
> * ixgbe_setup_kr_x550em - Configure the KR PHY
> * @hw: pointer to hardware structure
> - *
> - * Configures the integrated KR PHY for X550EM_x.
> **/
> static s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
> {
> - if (hw->mac.type != ixgbe_mac_X550EM_x)
> + /* leave linke alone for 2.5G */
Link, maybe?
> + if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL)
> return 0;
>
> return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
MBR, Sergei
^ permalink raw reply
* More info about lockless qdisc patch
From: Xingjun Liu @ 2016-12-30 12:48 UTC (permalink / raw)
To: john.r.fastabend; +Cc: netdev
Hi John,
I note you have a patch request last august about "support lockless qdisc”,
see: https://www.mail-archive.com/netdev@vger.kernel.org/msg124489.html
We take an interest in it. Do you have any info/plan on this patch?
Thanks
Xingjun
^ permalink raw reply
* [PATCH] net: stmmac: remove unused duplicate property snps,axi_all
From: Niklas Cassel @ 2016-12-30 12:56 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Giuseppe Cavallaro, Alexandre Torgue,
David S. Miller, Niklas Cassel, Eric Engestrom, Gabriel Fernandez,
Joachim Eastwood, Vincent Palatin
Cc: Niklas Cassel, netdev, devicetree, linux-kernel
From: Niklas Cassel <niklas.cassel@axis.com>
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
---
Documentation/devicetree/bindings/net/stmmac.txt | 1 -
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 1 -
include/linux/stmmac.h | 1 -
3 files changed, 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index 128da752fec9..c3d2fd480a1b 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -65,7 +65,6 @@ Optional properties:
- snps,wr_osr_lmt: max write outstanding req. limit
- snps,rd_osr_lmt: max read outstanding req. limit
- snps,kbbe: do not cross 1KiB boundary.
- - snps,axi_all: align address
- snps,blen: this is a vector of supported burst length.
- snps,fb: fixed-burst
- snps,mb: mixed-burst
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 082cd48db6a7..60ba8993c650 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -121,7 +121,6 @@ static struct stmmac_axi *stmmac_axi_setup(struct platform_device *pdev)
axi->axi_lpi_en = of_property_read_bool(np, "snps,lpi_en");
axi->axi_xit_frm = of_property_read_bool(np, "snps,xit_frm");
axi->axi_kbbe = of_property_read_bool(np, "snps,axi_kbbe");
- axi->axi_axi_all = of_property_read_bool(np, "snps,axi_all");
axi->axi_fb = of_property_read_bool(np, "snps,axi_fb");
axi->axi_mb = of_property_read_bool(np, "snps,axi_mb");
axi->axi_rb = of_property_read_bool(np, "snps,axi_rb");
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 266dab9ad782..889e0e9a3f1c 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -103,7 +103,6 @@ struct stmmac_axi {
u32 axi_wr_osr_lmt;
u32 axi_rd_osr_lmt;
bool axi_kbbe;
- bool axi_axi_all;
u32 axi_blen[AXI_BLEN];
bool axi_fb;
bool axi_mb;
--
2.1.4
^ permalink raw reply related
* Re: net: wireless: ath: wil6210: constify cfg80211_ops structures
From: Kalle Valo @ 2016-12-30 13:01 UTC (permalink / raw)
To: Bhumika Goyal
Cc: julia.lawall, qca_merez, linux-wireless, wil6210, netdev,
linux-kernel, Bhumika Goyal
In-Reply-To: <1482014667-27082-1-git-send-email-bhumirks@gmail.com>
Bhumika Goyal <bhumirks@gmail.com> wrote:
> cfg80211_ops structures are only passed as an argument to the function
> wiphy_new. This argument is of type const, so cfg80211_ops strutures
> having this property can be declared as const.
> Done using Coccinelle
>
> @r1 disable optional_qualifier @
> identifier i;
> position p;
> @@
> static struct cfg80211_ops i@p = {...};
>
> @ok1@
> identifier r1.i;
> position p;
> @@
> wiphy_new(&i@p,...)
>
> @bad@
> position p!={r1.p,ok1.p};
> identifier r1.i;
> @@
> i@p
>
> @depends on !bad disable optional_qualifier@
> identifier r1.i;
> @@
> +const
> struct cfg80211_ops i;
>
> File size before:
> text data bss dec hex filename
> 18133 6632 0 24765 60bd wireless/ath/wil6210/cfg80211.o
>
> File size after:
> text data bss dec hex filename
> 18933 5832 0 24765 60bd wireless/ath/wil6210/cfg80211.o
>
> Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
The prefix should be "wil6210:", I can fix that before I commit this.
--
https://patchwork.kernel.org/patch/9479127/
Documentation about submitting wireless patches and checking status
from patchwork:
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
* RE: [net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane
From: Rosen, Rami @ 2016-12-30 13:01 UTC (permalink / raw)
To: Sergei Shtylyov, Kirsher, Jeffrey T, davem@davemloft.net
Cc: Skidmore, Donald C, netdev@vger.kernel.org, nhorman@redhat.com,
sassmann@redhat.com, jogreene@redhat.com,
guru.anbalagane@oracle.com
In-Reply-To: <7a268273-d95d-16b4-a6a4-653caad791e9@cogentembedded.com>
Hi,
Hi,
On this occasion, also the next can be fixed:
> From: Don Skidmore <donald.c.skidmore@intel.com>
>
> This patch ensures that the advertised link speeds are configured for
> X553 KR/KX backplane. Without this patch the link remains at 1G when
> resuming form low power after being downshifted by LPLU.
Should be "from" instead "from", I would assume.
Regards,
Rami Rosen
Intel Corporation
^ permalink raw reply
* Re: net: wireless: marvell: libertas: constify cfg80211_ops structures
From: Kalle Valo @ 2016-12-30 13:02 UTC (permalink / raw)
To: Bhumika Goyal
Cc: julia.lawall, libertas-dev, linux-wireless, netdev, linux-kernel,
Bhumika Goyal
In-Reply-To: <1482015444-28899-1-git-send-email-bhumirks@gmail.com>
Bhumika Goyal <bhumirks@gmail.com> wrote:
> cfg80211_ops structures are only passed as an argument to the function
> wiphy_new. This argument is of type const, so cfg80211_ops strutures
> having this property can be declared as const.
> Done using Coccinelle
>
> @r1 disable optional_qualifier @
> identifier i;
> position p;
> @@
> static struct cfg80211_ops i@p = {...};
>
> @ok1@
> identifier r1.i;
> position p;
> @@
> wiphy_new(&i@p,...)
>
> @bad@
> position p!={r1.p,ok1.p};
> identifier r1.i;
> @@
> i@p
>
> @depends on !bad disable optional_qualifier@
> identifier r1.i;
> @@
> +const
> struct cfg80211_ops i;
>
> File size before:
> text data bss dec hex filename
> 21225 1954 16 23195 5a9b wireless/marvell/libertas/cfg.o
>
> File size after:
> text data bss dec hex filename
> 22041 1154 16 23211 5aab wireless/marvell/libertas/cfg.o
>
> Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
The prefix should be "libertas:", I can fix that before I commit.
--
https://patchwork.kernel.org/patch/9479131/
Documentation about submitting wireless patches and checking status
from patchwork:
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
* Re: libertas: constify cfg80211_ops structures
From: Kalle Valo @ 2016-12-30 13:56 UTC (permalink / raw)
To: Bhumika Goyal
Cc: julia.lawall, libertas-dev, linux-wireless, netdev, linux-kernel,
Bhumika Goyal
In-Reply-To: <1482015444-28899-1-git-send-email-bhumirks@gmail.com>
Bhumika Goyal <bhumirks@gmail.com> wrote:
> cfg80211_ops structures are only passed as an argument to the function
> wiphy_new. This argument is of type const, so cfg80211_ops strutures
> having this property can be declared as const.
> Done using Coccinelle
>
> @r1 disable optional_qualifier @
> identifier i;
> position p;
> @@
> static struct cfg80211_ops i@p = {...};
>
> @ok1@
> identifier r1.i;
> position p;
> @@
> wiphy_new(&i@p,...)
>
> @bad@
> position p!={r1.p,ok1.p};
> identifier r1.i;
> @@
> i@p
>
> @depends on !bad disable optional_qualifier@
> identifier r1.i;
> @@
> +const
> struct cfg80211_ops i;
>
> File size before:
> text data bss dec hex filename
> 21225 1954 16 23195 5a9b wireless/marvell/libertas/cfg.o
>
> File size after:
> text data bss dec hex filename
> 22041 1154 16 23211 5aab wireless/marvell/libertas/cfg.o
>
> Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Patch applied to wireless-drivers-next.git, thanks.
26eb994d5239 libertas: constify cfg80211_ops structures
--
https://patchwork.kernel.org/patch/9479131/
Documentation about submitting wireless patches and checking status
from patchwork:
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
* Re: rtlwifi: fix spelling mistake: "contry" -> "country"
From: Kalle Valo @ 2016-12-30 13:57 UTC (permalink / raw)
To: Colin Ian King
Cc: Larry Finger, Chaoming Li, linux-wireless, netdev, linux-kernel
In-Reply-To: <20161229160029.22117-1-colin.king@canonical.com>
Colin Ian King <colin.king@canonical.com> wrote:
> From: Colin Ian King <colin.king@canonical.com>
>
> trivial fix to spelling mistake in RT_TRACE message
>
> Signed-off-by: Colin Ian King <colin.king@canonical.com>
> Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Patch applied to wireless-drivers-next.git, thanks.
3b1fc7680a0f rtlwifi: fix spelling mistake: "contry" -> "country"
--
https://patchwork.kernel.org/patch/9491293/
Documentation about submitting wireless patches and checking status
from patchwork:
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
* Re: brcmfmac: fix spelling mistakes on "Ivalid"
From: Kalle Valo @ 2016-12-30 13:59 UTC (permalink / raw)
To: Colin Ian King
Cc: Arend van Spriel, Franky Lin, Hante Meuleman,
Pieter-Paul Giesberts, Rafał Miłecki, linux-wireless,
brcm80211-dev-list.pdl, netdev, linux-kernel
In-Reply-To: <20161223004322.7300-1-colin.king@canonical.com>
Colin Ian King <colin.king@canonical.com> wrote:
> From: Colin Ian King <colin.king@canonical.com>
>
> Trivial fixes to spelling mistake "Ivalid" to "Invalid" in
> brcmf_err error messages.
>
> Signed-off-by: Colin Ian King <colin.king@canonical.com>
> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Patch applied to wireless-drivers-next.git, thanks.
ad334bbb07b0 brcmfmac: fix spelling mistakes on "Ivalid"
--
https://patchwork.kernel.org/patch/9487009/
Documentation about submitting wireless patches and checking status
from patchwork:
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
* [PATCH] ath9k: fix spelling mistake: "meaurement" -> "measurement"
From: Colin King @ 2016-12-30 14:06 UTC (permalink / raw)
To: QCA ath9k Development, Kalle Valo,
linux-wireless-u79uwXL29TY76Z2rM5mHXA,
ath9k-devel-xDcbHBWguxHbcTqmT+pZeQ, netdev-u79uwXL29TY76Z2rM5mHXA
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA
From: Colin Ian King <colin.king-Z7WLFzj8eWMS+FvcfC7Uqw@public.gmane.org>
Trivial fix to spelling mistake in ath_err message
Signed-off-by: Colin Ian King <colin.king-Z7WLFzj8eWMS+FvcfC7Uqw@public.gmane.org>
---
drivers/net/wireless/ath/ath9k/hw.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index a35f78b..ac36873 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -731,7 +731,7 @@ u32 ar9003_get_pll_sqsum_dvc(struct ath_hw *ah)
udelay(100);
if (WARN_ON_ONCE(i >= 100)) {
- ath_err(common, "PLL4 meaurement not done\n");
+ ath_err(common, "PLL4 measurement not done\n");
break;
}
--
2.10.2
^ permalink raw reply related
* Re: [PATCH][V2] [media] gp8psk: fix spelling mistake: "firmare" -> "firmware"
From: Kalle Valo @ 2016-12-30 14:35 UTC (permalink / raw)
To: Colin King
Cc: Mauro Carvalho Chehab, Larry Finger, Chaoming Li, linux-media,
linux-wireless, netdev, linux-kernel
In-Reply-To: <20161229213815.27890-1-colin.king@canonical.com>
Colin King <colin.king@canonical.com> writes:
> From: Colin Ian King <colin.king@canonical.com>
>
> Trivial fix to spelling mistake in err message. Also change "don't" to
> "does not".
>
> Signed-off-by: Colin Ian King <colin.king@canonical.com>
> ---
> drivers/media/usb/dvb-usb/gp8psk.c | 2 +-
> drivers/net/wireless/realtek/rtlwifi/core.c | 2 +-
> 2 files changed, 2 insertions(+), 2 deletions(-)
Could you split the rtlwifi part to it's own patch? I can't apply
patches touching media drivers.
--
Kalle Valo
^ permalink raw reply
* [PATCH][V3] rtlwifi: fix spelling mistake: "encrypiton" -> "encryption"
From: Colin King @ 2016-12-30 14:50 UTC (permalink / raw)
To: Larry Finger, Chaoming Li, Kalle Valo, linux-wireless, netdev
Cc: linux-kernel
From: Colin Ian King <colin.king@canonical.com>
trivial fix to spelling mistake in RT_TRACE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
drivers/net/wireless/realtek/rtlwifi/core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/realtek/rtlwifi/core.c b/drivers/net/wireless/realtek/rtlwifi/core.c
index ded1493..732de0a 100644
--- a/drivers/net/wireless/realtek/rtlwifi/core.c
+++ b/drivers/net/wireless/realtek/rtlwifi/core.c
@@ -1532,7 +1532,7 @@ static int rtl_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
key_type = AESCMAC_ENCRYPTION;
RT_TRACE(rtlpriv, COMP_SEC, DBG_DMESG, "alg:CMAC\n");
RT_TRACE(rtlpriv, COMP_SEC, DBG_DMESG,
- "HW don't support CMAC encrypiton, use software CMAC encrypiton\n");
+ "HW don't support CMAC encryption, use software CMAC encryption\n");
err = -EOPNOTSUPP;
goto out_unlock;
default:
--
2.10.2
^ permalink raw reply related
* Re: [net-next PATCH 5/6] i40e: Add TX and RX support in switchdev mode.
From: Or Gerlitz @ 2016-12-30 15:31 UTC (permalink / raw)
To: Sridhar Samudrala
Cc: Alexander Duyck, John Fastabend, Anjali Singhai Jain,
jakub.kicinski, intel-wired-lan, Linux Netdev List
In-Reply-To: <1483078863-22026-6-git-send-email-sridhar.samudrala@intel.com>
On Fri, Dec 30, 2016 at 8:21 AM, Sridhar Samudrala
<sridhar.samudrala@intel.com> wrote:
> In switchdev mode, broadcast filter is not enabled on VFs, The broadcasts and
nit ", The broadcast" --> ", the broadcasts" or ". The broadcasts"
> unknown frames from VFs are received by the PF and passed to corresponding VF
> port representator netdev.
> A host based switching entity like a linux bridge or OVS redirects these frames
> to the right VFs via VFPR netdevs. Any frames sent via VFPR netdevs are sent as
> directed transmits to the corresponding VFs. To enable directed transmit, skb
> metadata dst is used to pass the VF id and the frame is requeued to call the PFs
> transmit routine.
So the representator netdevs do or don't have TX/RX rings of their
own? if the latter, was there any special locking you had to do for
that?
Are you exposing switchdev ops for the representators? didn't see that
or maybe it's in the 4th patch which didn't make it to the list?
^ permalink raw reply
* Re: [net-next PATCH 3/6] i40e: Sync link state between VFs and VFPRs
From: Or Gerlitz @ 2016-12-30 15:43 UTC (permalink / raw)
To: Sridhar Samudrala
Cc: Alexander Duyck, John Fastabend, Anjali Singhai Jain,
jakub.kicinski, intel-wired-lan, Linux Netdev List
In-Reply-To: <1483078863-22026-4-git-send-email-sridhar.samudrala@intel.com>
On Fri, Dec 30, 2016 at 8:21 AM, Sridhar Samudrala
<sridhar.samudrala@intel.com> wrote:
[..]
> - enable/disable VF link state via ndo_set_vf_link_state will update the
> admin state of associated VFPR.
why you want to do that? anything missing here w.o using the legacy mode?
^ permalink raw reply
* Re: [net-next PATCH 0/6] i40e: Add VF port representator support or SR-IOV VFs
From: Samudrala, Sridhar @ 2016-12-30 16:55 UTC (permalink / raw)
To: David Miller
Cc: alexander.h.duyck, john.r.fastabend, anjali.singhai,
jakub.kicinski, intel-wired-lan, netdev
In-Reply-To: <20161229.215356.2143143534347167491.davem@davemloft.net>
On 12/29/2016 6:53 PM, David Miller wrote:
> From: Sridhar Samudrala <sridhar.samudrala@intel.com>
> Date: Thu, 29 Dec 2016 22:20:57 -0800
>
>> - Patch 1 introduces devlink interface to get/set the mode of SRIOV switch.
>> - Patch 2 adds support to create VF port representor(VFPR) netdevs associated
>> with SR-IOV VFs that can be used to control/configure VFs from PF name space.
>> - Patch 3 enables syncing link state between VFs and VFPRs.
>> - Patch 4 adds a new type to metadata_dst to allow passing VF id to lower device.
>> - Patch 5 adds TX and RX support to VFPR netdevs.
>> - Patch 6 enables HW and SW VFPR statistics to be exposed via netlink on VFPR
>> netdevs.
> Patch 4 did not show up on the lists.
I see it on intel-wired-lan list. not sure why it didn't make it to netdev.
>
> The computer you did this work on is configured with a time in the future.
Will fix and send a v2 that will address other comments and include patch 4.
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox