* [PATCH net-next] net: sk_pacing_shift_update() helper
From: Eric Dumazet @ 2017-12-12 14:34 UTC (permalink / raw)
To: Felix Fietkau, David Miller
Cc: netdev, Johannes Berg, Toke Høiland-Jørgensen,
Kir Kolyshkin
In-Reply-To: <1511890429.16595.20.camel@gmail.com>
From: Eric Dumazet <edumazet@google.com>
In commit 3a9b76fd0db9 ("tcp: allow drivers to tweak TSQ logic")
I gave a code sample to set sk->sk_pacing_shift that was not complete.
Better add a helper that can be used by drivers without worries,
and maybe amended in the future.
A wifi driver might use it from its ndo_start_xmit()
Following call would setup TCP to allow up to ~8ms of queued data per
flow.
sk_pacing_shift_update(skb->sk, 7);
Signed-off-by: Eric Dumazet <edumazet@google.com>
---
include/net/sock.h | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/include/net/sock.h b/include/net/sock.h
index 9155da42269208b358df8535b14dfd3dba509365..9a9047268d375496bccc954d03ec20baf4177fd3 100644
--- a/include/net/sock.h
+++ b/include/net/sock.h
@@ -2407,4 +2407,15 @@ static inline int sk_get_rmem0(const struct sock *sk, const struct proto *proto)
return *proto->sysctl_rmem;
}
+/* Default TCP Small queue budget is ~1 ms of data (1sec >> 10)
+ * Some wifi drivers need to tweak it to get more chunks.
+ * They can use this helper from their ndo_start_xmit()
+ */
+static inline void sk_pacing_shift_update(struct sock *sk, int val)
+{
+ if (!sk || !sk_fullsock(sk) || sk->sk_pacing_shift == val)
+ return;
+ sk->sk_pacing_shift = val;
+}
+
#endif /* _SOCK_H */
^ permalink raw reply related
* [PATCH net-next] tcp: Remove tcp_low_latency sysctl.
From: Tonghao Zhang @ 2017-12-12 14:43 UTC (permalink / raw)
To: fw; +Cc: netdev, Tonghao Zhang
The prequeue has been removed from the kernel. If we leave
the tcp_low_latency in kernel, it may confuse the users.
If users can't find the option, the doc may tell them why.
So we remove also the sysctl about tcp_low_latency.
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
---
Documentation/networking/ip-sysctl.txt | 2 +-
net/ipv4/sysctl_net_ipv4.c | 10 ----------
2 files changed, 1 insertion(+), 11 deletions(-)
diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt
index 77f4de59dc9c..ac35f5b59739 100644
--- a/Documentation/networking/ip-sysctl.txt
+++ b/Documentation/networking/ip-sysctl.txt
@@ -356,7 +356,7 @@ tcp_l3mdev_accept - BOOLEAN
compiled with CONFIG_NET_L3_MASTER_DEV.
tcp_low_latency - BOOLEAN
- This is a legacy option, it has no effect anymore.
+ This is an obsolete option, it has been removed from kernel.
tcp_max_orphans - INTEGER
Maximal number of TCP sockets not attached to any user file handle,
diff --git a/net/ipv4/sysctl_net_ipv4.c b/net/ipv4/sysctl_net_ipv4.c
index 4602af6d5358..dfebbfcccb87 100644
--- a/net/ipv4/sysctl_net_ipv4.c
+++ b/net/ipv4/sysctl_net_ipv4.c
@@ -45,9 +45,6 @@ static int tcp_syn_retries_max = MAX_TCP_SYNCNT;
static int ip_ping_group_range_min[] = { 0, 0 };
static int ip_ping_group_range_max[] = { GID_T_MAX, GID_T_MAX };
-/* obsolete */
-static int sysctl_tcp_low_latency __read_mostly;
-
/* Update system visible IP port range */
static void set_local_port_range(struct net *net, int range[2])
{
@@ -438,13 +435,6 @@ static struct ctl_table ipv4_table[] = {
.extra1 = &one,
},
{
- .procname = "tcp_low_latency",
- .data = &sysctl_tcp_low_latency,
- .maxlen = sizeof(int),
- .mode = 0644,
- .proc_handler = proc_dointvec
- },
- {
.procname = "tcp_congestion_control",
.mode = 0644,
.maxlen = TCP_CA_NAME_MAX,
--
2.13.6
^ permalink raw reply related
* Re: [PATCH net-next] tcp: Remove tcp_low_latency sysctl.
From: David Miller @ 2017-12-12 14:49 UTC (permalink / raw)
To: xiangxia.m.yue; +Cc: fw, netdev
In-Reply-To: <1513089788-2626-1-git-send-email-xiangxia.m.yue@gmail.com>
From: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Date: Tue, 12 Dec 2017 06:43:08 -0800
> The prequeue has been removed from the kernel. If we leave
> the tcp_low_latency in kernel, it may confuse the users.
> If users can't find the option, the doc may tell them why.
> So we remove also the sysctl about tcp_low_latency.
>
> Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
If you remove the sysctl, it will break scripts.
That's why we left it around.
^ permalink raw reply
* Re: [PATCH net-next] net: phy: marvell10g: remove XGMII as an option for 88x3310
From: Andrew Lunn @ 2017-12-12 14:59 UTC (permalink / raw)
To: Russell King; +Cc: Florian Fainelli, netdev
In-Reply-To: <E1eOk3i-00010j-0V@rmk-PC.armlinux.org.uk>
On Tue, Dec 12, 2017 at 12:53:18PM +0000, Russell King wrote:
> Remove XGMII as an option for the 88x3310 PHY driver, as the PHY doesn't
> support XGMII's 32-bit data lanes. It supports USXGMII, which is not
> XGMII, but a single-lane serdes interface - see
> https://developer.cisco.com/site/usgmii-usxgmii/
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Andrew
^ permalink raw reply
* Re: [RFC PATCH 0/9] ethtool netlink interface (WiP)
From: Roopa Prabhu @ 2017-12-12 15:32 UTC (permalink / raw)
To: Michal Kubecek; +Cc: netdev, linux-kernel
In-Reply-To: <cover.1513000306.git.mkubecek@suse.cz>
On Mon, Dec 11, 2017 at 5:53 AM, Michal Kubecek <mkubecek@suse.cz> wrote:
> This is still work in progress and only a very small part of the ioctl
> interface is reimplemented but I would like to get some comments before
> the patchset becomes too big and changing things becomes too tedious.
>
> The interface used for communication between ethtool and kernel is based on
> ioctl() and suffers from many problems. The most pressing seems the be the
> lack of extensibility. While some of the newer commands use structures
> designed to allow future extensions (e.g. GFEATURES or TEST), most either
> allow no extension at all (GPAUSEPARAM, GCOALESCE) or only limited set of
> reserved fields (GDRVINFO, GEEE). Even most of those which support future
> extensions limit the data types that can be used.
>
> This series aims to provide an alternative interface based on netlink which
> is what other network configuration utilities use. In particular, it uses
> generic netlink (family "ethtool"). The goal is to provide an interface
> which would be extensible, flexible and practical both for ethtool and for
> other network configuration tools (e.g. wicked or systemd-networkd).
>
> The interface is documented in Documentation/networking/ethtool-netlink.txt
>
> I'll post RFC patch series for ethtool in a few days, it still needs some
> more polishing.
>
> Basic concepts:
>
> - the interface is based on generic netlink (family name "ethtool")
>
> - provide everything ioctl can do but allow easier future extensions
>
> - inextensibility of ioctl interface resulted in way too many commands,
> many of them obsoleted by newer ones; reduce the number by ignoring the
> obsolete commands and grouping some together
>
> - for "set" type commands, netlink allows providing only the attributes to
> be changed; therefore we don't need a get-modify-set cycle, userspace can
> simply say what it wants to change and how
>
> - be less dependent on ethtool and kernel being in sync; allow e.g. saying
> "ethtool -s eth0 advertise xyz off" without knowing what "xyz" means;
> it's kernel's job to know what mode "xyz" is and if it exists and is
> supported
>
> Unresolved questions/tasks:
>
> - allow dumps for "get" type requests, e.g. listing EEE settings for all
> interfaces in current netns
>
> - find reasonable format for data transfers (e.g. eeprom dump or flash)
>
> - while the netlink interface allows easy future extensions, ethtool_ops
> interface does not; some settings could be implemented using tunables and
> accessed via relevant netlink messages (as well as tunables) from
> userspace but in the long term, something better will be needed
>
> - it would be nice if driver could provide useful error/warning messages to
> be passed to userspace via extended ACK; example: while testing, I found
> a driver which only allows values 0, 1, 3 and 10000 for certain parameter
> but the only way poor user can find out is either by trying all values or
> by checking driver source
>
> Michal Kubecek (9):
> netlink: introduce nla_put_bitfield32()
> ethtool: introduce ethtool netlink interface
> ethtool: helper functions for netlink interface
> ethtool: netlink bitset handling
> ethtool: implement GET_DRVINFO message
> ethtool: implement GET_SETTINGS message
> ethtool: implement SET_SETTINGS message
> ethtool: implement GET_PARAMS message
> ethtool: implement SET_PARAMS message
>
Thanks for working on this!. Agree with most comments already
discussed on this thread.
I would prefer if we fold ethtool netlink into devlink since there is
already an overlap.
many reasons:
- have just one driver api for device global and per port config
(devlink already provides that)
- some of the devlink commands like port split/unsplit can already be
applied per netdev (and since you bring up network interface managers,
we are looking at getting these in network managers for switch ports)
- if we keep them separate, we will soon see that drivers will need
handlers for both devlink and ethtool
- and the overlap is going to be confusing for both drivers and
user-space
^ permalink raw reply
* [PATCH iproute2] tc: bash-completion: add missing 'classid' keyword
From: Davide Caratti @ 2017-12-12 15:45 UTC (permalink / raw)
To: Stephen Hemminger, netdev; +Cc: Yotam Gigi
users of 'matchall' filter can specify a value for the class id: update
bash-completion accordingly.
Fixes: b32c0b64fa2b ("tc: bash-completion: Add support for matchall")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
---
bash-completion/tc | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/bash-completion/tc b/bash-completion/tc
index 80d12972..29bca5d9 100644
--- a/bash-completion/tc
+++ b/bash-completion/tc
@@ -450,7 +450,7 @@ _tc_filter_options()
return 0
;;
matchall)
- _tc_once_attr 'action skip_sw skip_hw'
+ _tc_once_attr 'action classid skip_sw skip_hw'
return 0
;;
flower)
--
2.13.6
^ permalink raw reply related
* Re: [PATCH net-next 0/3] tcp: better receiver autotuning
From: David Miller @ 2017-12-12 15:53 UTC (permalink / raw)
To: edumazet; +Cc: ncardwell, ycheng, soheil, weiwan, priyarjha, netdev,
eric.dumazet
In-Reply-To: <20171211015504.26551-1-edumazet@google.com>
From: Eric Dumazet <edumazet@google.com>
Date: Sun, 10 Dec 2017 17:55:01 -0800
> Now TCP senders no longer backoff when a drop is detected,
> it appears we are very often receive window limited.
>
> This series makes tcp_rcv_space_adjust() slightly more robust
> and responsive.
Series applied, thanks.
^ permalink raw reply
* gso_type field for LRO packets
From: Gal Pressman @ 2017-12-12 15:53 UTC (permalink / raw)
To: netdev@vger.kernel.org, Eric Dumazet, David S. Miller,
Ben Hutchings, Michael S. Tsirkin
Cc: Tariq Toukan, Saeed Mahameed
Hi all,
I've been exploring hardware LRO related code in the stack and came across an inconsistency I don't quite understand.
When receiving a hardware LRO packet, most of the drivers set skb_shinfo(skb)->gso_type (For example [1]) in order to prevent macvtap from breaking.
According to include/linux/skbuff.h +/skb_warn_if_lro, LRO should set gso_size but not gso_type, which contradicts the drivers implementation and makes the check redundant.
Can anyone advise what is the correct driver implementation? should we change skb_warn_if_lro() implementation?
Regards,
Gal
[1] commit bd69ba798e21 ("qlcnic: set gso_type")
^ permalink raw reply
* Re: [PATCH net-next] libbpf: add function to setup XDP
From: David Miller @ 2017-12-12 15:53 UTC (permalink / raw)
To: makita.toshiaki; +Cc: eric, netdev, linux-kernel, ast, daniel
In-Reply-To: <c1be066a-eb39-c9e0-b21b-4bb4da280b26@lab.ntt.co.jp>
From: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Date: Mon, 11 Dec 2017 11:24:12 +0900
> On 2017/12/09 23:43, Eric Leblond wrote:
>> Most of the code is taken from set_link_xdp_fd() in bpf_load.c and
>> slightly modified to be library compliant.
>>
>> Signed-off-by: Eric Leblond <eric@regit.org>
> ...
>> +int bpf_set_link_xdp_fd(int ifindex, int fd, __u32 flags)
> ...
>> + for (nh = (struct nlmsghdr *)buf; NLMSG_OK(nh, len);
>> + nh = NLMSG_NEXT(nh, len)) {
>> + if (nh->nlmsg_pid != getpid()) {
>
> Generally nlmsg_pid should not be compared with process id.
> See man netlink and
> https://github.com/iovisor/bcc/pull/1275/commits/69ce96a54c55960c8de3392061254c97b6306a6d
Right. I wish we had never named this "pid", it gets misinterpreted
way too easily.
^ permalink raw reply
* AF_VSOCK connection refused errno
From: Stefan Hajnoczi @ 2017-12-12 15:53 UTC (permalink / raw)
To: Jorgen Hansen; +Cc: Dexuan Cui, netdev
[-- Attachment #1: Type: text/plain, Size: 559 bytes --]
When connect(2) fails because the peer is not listening the virtio vsock
transport returns ECONNRESET. I believe the VMCI transport does the
same (based on code inspection).
Jorgen: Can you confirm this VMCI transport behavior?
I'd like to change to ECONNREFUSED for all transports because developers
will be surprised when they get ECONNRESET. It makes porting AF_INET
code harder.
On the other hand, it may be too late to fix this if there userspace
applications that rely on ECONNRESET? I'm not aware of any such
applications myself.
Thanks,
Stefan
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 455 bytes --]
^ permalink raw reply
* Re: [PATCH net-next v4 1/5] net: Introduce NETIF_F_GRO_HW.
From: Alexander Duyck @ 2017-12-12 15:57 UTC (permalink / raw)
To: Michael Chan
Cc: David Miller, Netdev, Andrew Gospodarek, Ariel Elior,
everest-linux-l2
In-Reply-To: <1512992470-28861-2-git-send-email-michael.chan@broadcom.com>
On Mon, Dec 11, 2017 at 3:41 AM, Michael Chan <michael.chan@broadcom.com> wrote:
> Introduce NETIF_F_GRO_HW feature flag for NICs that support hardware
> GRO. With this flag, we can now independently turn on or off hardware
> GRO when GRO is on. Previously, drivers were using NETIF_F_GRO to
> control hardware GRO and so it cannot be independently turned on or
> off without affecting GRO.
>
> Hardware GRO (just like GRO) guarantees that packets can be re-segmented
> by TSO/GSO to reconstruct the original packet stream. Logically,
> GRO_HW should depend on GRO since it a subset, but we will let
> individual drivers enforce this dependency as they see fit.
>
> Since NETIF_F_GRO is not propagated between upper and lower devices,
> NETIF_F_GRO_HW should follow suit since it is a subset of GRO. In other
> words, a lower device can independent have GRO/GRO_HW enabled or disabled
> and no feature propagation is required. This will preserve the current
> GRO behavior. This can be changed later if we decide to propagate GRO/
> GRO_HW/RXCSUM from upper to lower devices.
>
> Cc: Ariel Elior <Ariel.Elior@cavium.com>
> Cc: everest-linux-l2@cavium.com
> Signed-off-by: Michael Chan <michael.chan@broadcom.com>
> ---
> Documentation/networking/netdev-features.txt | 8 ++++++++
> include/linux/netdev_features.h | 3 +++
> net/core/dev.c | 10 ++++++++++
> net/core/ethtool.c | 1 +
> 4 files changed, 22 insertions(+)
>
> diff --git a/Documentation/networking/netdev-features.txt b/Documentation/networking/netdev-features.txt
> index 7413eb0..8f36527 100644
> --- a/Documentation/networking/netdev-features.txt
> +++ b/Documentation/networking/netdev-features.txt
> @@ -163,3 +163,11 @@ This requests that the NIC receive all possible frames, including errored
> frames (such as bad FCS, etc). This can be helpful when sniffing a link with
> bad packets on it. Some NICs may receive more packets if also put into normal
> PROMISC mode.
> +
> +* rx-gro-hw
> +
> +This requests that the NIC enables Hardware GRO (generic receive offload).
> +Hardware GRO is basically the exact reverse of TSO, and is generally
> +stricter than Hardware LRO. A packet stream merged by Hardware GRO must
> +be re-segmentable by GSO or TSO back to the exact original packet stream.
> +Hardware GRO is dependent on GRO and RXCSUM.
This last line should probably be updated since we made the change
that dropped the dependency on software GRO.
> diff --git a/include/linux/netdev_features.h b/include/linux/netdev_features.h
> index b1b0ca7..db84c51 100644
> --- a/include/linux/netdev_features.h
> +++ b/include/linux/netdev_features.h
> @@ -78,6 +78,8 @@ enum {
> NETIF_F_HW_ESP_TX_CSUM_BIT, /* ESP with TX checksum offload */
> NETIF_F_RX_UDP_TUNNEL_PORT_BIT, /* Offload of RX port for UDP tunnels */
>
> + NETIF_F_GRO_HW_BIT, /* Hardware Generic receive offload */
> +
> /*
> * Add your fresh new feature above and remember to update
> * netdev_features_strings[] in net/core/ethtool.c and maybe
> @@ -97,6 +99,7 @@ enum {
> #define NETIF_F_FRAGLIST __NETIF_F(FRAGLIST)
> #define NETIF_F_FSO __NETIF_F(FSO)
> #define NETIF_F_GRO __NETIF_F(GRO)
> +#define NETIF_F_GRO_HW __NETIF_F(GRO_HW)
> #define NETIF_F_GSO __NETIF_F(GSO)
> #define NETIF_F_GSO_ROBUST __NETIF_F(GSO_ROBUST)
> #define NETIF_F_HIGHDMA __NETIF_F(HIGHDMA)
> diff --git a/net/core/dev.c b/net/core/dev.c
> index 8aa2f70..bf0149e 100644
> --- a/net/core/dev.c
> +++ b/net/core/dev.c
> @@ -7424,6 +7424,16 @@ static netdev_features_t netdev_fix_features(struct net_device *dev,
> features &= ~dev->gso_partial_features;
> }
>
> + if (!(features & NETIF_F_RXCSUM)) {
> + /* NETIF_F_GRO_HW implies doing RXCSUM. If the user does not
> + * want to enable RXCSUM, logically, we should disable GRO_HW.
> + */
It might be in our interest here to explain why. Specifically that
"The Rx checksum can no longer be verified once a packet is modified
as a result of GRO_HW, therefore we cannot allow GRO_HW to be enabled
when RXCSUM is disabled." or something to that effect. Otherwise there
isn't a good explanation as to why GRO_HW implies this.
> + if (features & NETIF_F_GRO_HW) {
> + netdev_dbg(dev, "Dropping NETIF_F_GRO_HW since no RXCSUM feature.\n");
> + features &= ~NETIF_F_GRO_HW;
> + }
> + }
> +
> return features;
> }
>
> diff --git a/net/core/ethtool.c b/net/core/ethtool.c
> index f8fcf45..50a7920 100644
> --- a/net/core/ethtool.c
> +++ b/net/core/ethtool.c
> @@ -73,6 +73,7 @@ int ethtool_op_get_ts_info(struct net_device *dev, struct ethtool_ts_info *info)
> [NETIF_F_LLTX_BIT] = "tx-lockless",
> [NETIF_F_NETNS_LOCAL_BIT] = "netns-local",
> [NETIF_F_GRO_BIT] = "rx-gro",
> + [NETIF_F_GRO_HW_BIT] = "rx-gro-hw",
> [NETIF_F_LRO_BIT] = "rx-lro",
>
> [NETIF_F_TSO_BIT] = "tx-tcp-segmentation",
^ permalink raw reply
* Re: [PATCH 2/4] sctp: Add ip option support
From: Marcelo Ricardo Leitner @ 2017-12-12 16:08 UTC (permalink / raw)
To: Richard Haines
Cc: selinux, netdev, linux-sctp, linux-security-module, paul,
vyasevich, nhorman, sds, eparis
In-Reply-To: <20171127193121.2666-1-richard_c_haines@btinternet.com>
Hi Richard,
On Mon, Nov 27, 2017 at 07:31:21PM +0000, Richard Haines wrote:
...
> --- a/net/sctp/socket.c
> +++ b/net/sctp/socket.c
> @@ -3123,8 +3123,10 @@ static int sctp_setsockopt_maxseg(struct sock *sk, char __user *optval, unsigned
>
> if (asoc) {
> if (val == 0) {
> + struct sctp_af *af = sp->pf->af;
> val = asoc->pathmtu;
> - val -= sp->pf->af->net_header_len;
> + val -= af->ip_options_len(asoc->base.sk);
> + val -= af->net_header_len;
> val -= sizeof(struct sctphdr) +
> sizeof(struct sctp_data_chunk);
> }
Right below here there is a call to sctp_frag_point(). That function
also needs this tweak.
Yes, we should simplify all these calculations. I have a patch to use
sctp_frag_point on where it is currently recalculating it on
sctp_datamsg_from_user(), but probably should include other places as
well.
Marcelo
^ permalink raw reply
* [PATCH] veth: Optionally pad packets to minimum Ethernet length
From: Ed Swierk @ 2017-12-12 16:13 UTC (permalink / raw)
To: netdev; +Cc: Ed Swierk, Benjamin Warren, Keith Holleman
Most physical Ethernet devices pad short packets to the minimum length
of 64 bytes (including FCS) on transmit. It can be useful to simulate
this behavior when debugging a problem that results from it (such as
incorrect L4 checksum calculation).
Padding is unnecessary for most applications so leave it off by
default. Enable padding only when the otherwise unused IFF_AUTOMEDIA
flag is set (e.g. by writing 0x5003 to flags in sysfs).
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
---
drivers/net/veth.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/veth.c b/drivers/net/veth.c
index f5438d0978ca..292029bf4bb2 100644
--- a/drivers/net/veth.c
+++ b/drivers/net/veth.c
@@ -111,6 +111,12 @@ static netdev_tx_t veth_xmit(struct sk_buff *skb, struct net_device *dev)
goto drop;
}
+ if (unlikely(dev->flags & IFF_AUTOMEDIA)) {
+ /* if eth_skb_pad returns an error the skb was freed */
+ if (eth_skb_pad(skb))
+ goto drop;
+ }
+
if (likely(dev_forward_skb(rcv, skb) == NET_RX_SUCCESS)) {
struct pcpu_vstats *stats = this_cpu_ptr(dev->vstats);
--
2.11.0
^ permalink raw reply related
* [PATCH] openvswitch: Trim off padding before L3 conntrack processing
From: Ed Swierk @ 2017-12-12 16:17 UTC (permalink / raw)
To: ovs-dev, netdev, Pravin Shelar
Cc: Lance Richardson, Ed Swierk, Benjamin Warren, Keith Holleman
A short IPv4 packet may have up to 6 bytes of padding following the IP
payload when received on an Ethernet device.
In the normal IPv4 receive path, ip_rcv() trims the packet to
ip_hdr->tot_len before invoking NF_INET_PRE_ROUTING hooks (including
conntrack). Then any subsequent L3+ processing steps, like
nf_checksum(), use skb->len as the length of the packet, rather than
referring back to ip_hdr->tot_len. In the IPv6 receive path, ip6_rcv()
does the same using ipv6_hdr->payload_len.
In the OVS conntrack receive path, this trimming does not occur, so
the checksum verification in tcp_header() fails, printing "nf_ct_tcp:
bad TCP checksum". Extra zero bytes don't affect the checksum, but the
length in the IP pseudoheader does. That length is based on skb->len,
and without trimming, it doesn't match the length the sender used when
computing the checksum.
With this change, OVS conntrack trims IPv4 and IPv6 packets prior to
L3 processing.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
---
net/openvswitch/conntrack.c | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/net/openvswitch/conntrack.c b/net/openvswitch/conntrack.c
index d558e882ca0c..3a7c9215c431 100644
--- a/net/openvswitch/conntrack.c
+++ b/net/openvswitch/conntrack.c
@@ -1105,12 +1105,29 @@ int ovs_ct_execute(struct net *net, struct sk_buff *skb,
const struct ovs_conntrack_info *info)
{
int nh_ofs;
+ unsigned int nh_len;
int err;
/* The conntrack module expects to be working at L3. */
nh_ofs = skb_network_offset(skb);
skb_pull_rcsum(skb, nh_ofs);
+ /* Trim to L3 length since nf_checksum() doesn't expect padding. */
+ switch (skb->protocol) {
+ case htons(ETH_P_IP):
+ nh_len = ntohs(ip_hdr(skb)->tot_len);
+ break;
+ case htons(ETH_P_IPV6):
+ nh_len = ntohs(ipv6_hdr(skb)->payload_len)
+ + sizeof(struct ipv6hdr);
+ break;
+ default:
+ nh_len = skb->len;
+ }
+ err = pskb_trim_rcsum(skb, nh_len);
+ if (err)
+ return err;
+
if (key->ip.frag != OVS_FRAG_TYPE_NONE) {
err = handle_fragments(net, key, info->zone.id, skb);
if (err)
--
2.11.0
^ permalink raw reply related
* Re: [PATCH net] tcp md5sig: Use skb's saddr when replying to an incoming segment
From: David Miller @ 2017-12-12 16:21 UTC (permalink / raw)
To: cpaasch; +Cc: netdev
In-Reply-To: <20171211080546.89418-1-cpaasch@apple.com>
From: Christoph Paasch <cpaasch@apple.com>
Date: Mon, 11 Dec 2017 00:05:46 -0800
> The MD5-key that belongs to a connection is identified by the peer's
> IP-address. When we are in tcp_v4(6)_reqsk_send_ack(), we are replying
> to an incoming segment from tcp_check_req() that failed the seq-number
> checks.
>
> Thus, to find the correct key, we need to use the skb's saddr and not
> the daddr.
>
> This bug seems to have been there since quite a while, but probably got
> unnoticed because the consequences are not catastrophic. We will call
> tcp_v4_reqsk_send_ack only to send a challenge-ACK back to the peer,
> thus the connection doesn't really fail.
>
> Fixes: 9501f9722922 ("tcp md5sig: Let the caller pass appropriate key for tcp_v{4,6}_do_calc_md5_hash().")
> Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Applied and queued up for -stable, thanks.
^ permalink raw reply
* [PATCH v2 net-next] net: ethernet: ti: cpdma: correct error handling for chan create
From: Ivan Khoronzhuk @ 2017-12-12 16:35 UTC (permalink / raw)
To: grygorii.strashko
Cc: netdev, davem, linux-omap, linux-kernel, Ivan Khoronzhuk
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
duplicated dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
drivers/net/ethernet/ti/cpsw.c | 12 +++++++++---
drivers/net/ethernet/ti/davinci_cpdma.c | 2 +-
drivers/net/ethernet/ti/davinci_emac.c | 9 +++++++--
3 files changed, 17 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index a60a378..3c85a08 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -3065,10 +3065,16 @@ static int cpsw_probe(struct platform_device *pdev)
}
cpsw->txv[0].ch = cpdma_chan_create(cpsw->dma, 0, cpsw_tx_handler, 0);
+ if (IS_ERR(cpsw->txv[0].ch)) {
+ dev_err(priv->dev, "error initializing tx dma channel\n");
+ ret = PTR_ERR(cpsw->txv[0].ch);
+ goto clean_dma_ret;
+ }
+
cpsw->rxv[0].ch = cpdma_chan_create(cpsw->dma, 0, cpsw_rx_handler, 1);
- if (WARN_ON(!cpsw->rxv[0].ch || !cpsw->txv[0].ch)) {
- dev_err(priv->dev, "error initializing dma channels\n");
- ret = -ENOMEM;
+ if (IS_ERR(cpsw->rxv[0].ch)) {
+ dev_err(priv->dev, "error initializing rx dma channel\n");
+ ret = PTR_ERR(cpsw->rxv[0].ch);
goto clean_dma_ret;
}
diff --git a/drivers/net/ethernet/ti/davinci_cpdma.c b/drivers/net/ethernet/ti/davinci_cpdma.c
index e4d6edf..6f9173f 100644
--- a/drivers/net/ethernet/ti/davinci_cpdma.c
+++ b/drivers/net/ethernet/ti/davinci_cpdma.c
@@ -893,7 +893,7 @@ struct cpdma_chan *cpdma_chan_create(struct cpdma_ctlr *ctlr, int chan_num,
chan_num = rx_type ? rx_chan_num(chan_num) : tx_chan_num(chan_num);
if (__chan_linear(chan_num) >= ctlr->num_chan)
- return NULL;
+ return ERR_PTR(-EINVAL);
chan = devm_kzalloc(ctlr->dev, sizeof(*chan), GFP_KERNEL);
if (!chan)
diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c
index f58c0c6..3d4af64 100644
--- a/drivers/net/ethernet/ti/davinci_emac.c
+++ b/drivers/net/ethernet/ti/davinci_emac.c
@@ -1870,10 +1870,15 @@ static int davinci_emac_probe(struct platform_device *pdev)
priv->txchan = cpdma_chan_create(priv->dma, EMAC_DEF_TX_CH,
emac_tx_handler, 0);
+ if (WARN_ON(IS_ERR(priv->txchan))) {
+ rc = PTR_ERR(priv->txchan);
+ goto no_cpdma_chan;
+ }
+
priv->rxchan = cpdma_chan_create(priv->dma, EMAC_DEF_RX_CH,
emac_rx_handler, 1);
- if (WARN_ON(!priv->txchan || !priv->rxchan)) {
- rc = -ENOMEM;
+ if (WARN_ON(IS_ERR(priv->rxchan))) {
+ rc = PTR_ERR(priv->rxchan);
goto no_cpdma_chan;
}
--
2.7.4
^ permalink raw reply related
* [PATCH net-next] net: avoid skb_warn_bad_offload on IS_ERR
From: Willem de Bruijn @ 2017-12-12 16:39 UTC (permalink / raw)
To: netdev; +Cc: edumazet, davem, Willem de Bruijn
From: Willem de Bruijn <willemb@google.com>
skb_warn_bad_offload warns when packets enter the GSO stack that
require skb_checksum_help or vice versa. Do not warn on arbitrary
bad packets. Packet sockets can craft many. Syzkaller was able to
demonstrate another one with eth_type games.
In particular, suppress the warning when segmentation returns an
error, which is for reasons other than checksum offload.
See also commit 36c92474498a ("net: WARN if skb_checksum_help() is
called on skb requiring segmentation") for context on this warning.
Signed-off-by: Willem de Bruijn <willemb@google.com>
---
net/core/dev.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/core/dev.c b/net/core/dev.c
index 8aa2f70995e8..b0eee49a2489 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -2803,7 +2803,7 @@ struct sk_buff *__skb_gso_segment(struct sk_buff *skb,
segs = skb_mac_gso_segment(skb, features);
- if (unlikely(skb_needs_check(skb, tx_path)))
+ if (unlikely(skb_needs_check(skb, tx_path) && !IS_ERR(segs)))
skb_warn_bad_offload(skb);
return segs;
--
2.15.1.424.g9478a66081-goog
^ permalink raw reply related
* Re: [PATCH net-next v4 1/2] bpf/tracing: allow user space to query prog array on the same tp
From: Alexei Starovoitov @ 2017-12-12 16:54 UTC (permalink / raw)
To: Peter Zijlstra, Yonghong Song; +Cc: daniel, netdev, kernel-team
In-Reply-To: <20171212090331.umlkvftrm3helfww@hirez.programming.kicks-ass.net>
On 12/12/17 1:03 AM, Peter Zijlstra wrote:
> On Mon, Dec 11, 2017 at 11:39:02AM -0800, Yonghong Song wrote:
>> The usage:
>> struct perf_event_query_bpf *query = malloc(...);
>> query.ids_len = ids_len;
>> err = ioctl(pmu_efd, PERF_EVENT_IOC_QUERY_BPF, &query);
>
> You didn't spot the fixes to your changelog ;-) The above should read
> something like:
>
> struct perf_event_query_bpf *query =
> malloc(sizeof(*query) + sizeof(u32) * ids_len);
> query->ids_len = ids_len;
> err = ioctl(pmu_efd, PERF_EVENT_IOC_QUERY_BPF, query);
sure. I fixed up this nit in commit log of patch 1 and in test_progs.c
of patch 2.
^ permalink raw reply
* Re: [PATCH 2/4] sctp: Add ip option support
From: Marcelo Ricardo Leitner @ 2017-12-12 17:08 UTC (permalink / raw)
To: Richard Haines
Cc: selinux, netdev, linux-sctp, linux-security-module, paul,
vyasevich, nhorman, sds, eparis
In-Reply-To: <20171212160800.GE3532@localhost.localdomain>
On Tue, Dec 12, 2017 at 02:08:00PM -0200, Marcelo Ricardo Leitner wrote:
> Hi Richard,
>
> On Mon, Nov 27, 2017 at 07:31:21PM +0000, Richard Haines wrote:
> ...
> > --- a/net/sctp/socket.c
> > +++ b/net/sctp/socket.c
> > @@ -3123,8 +3123,10 @@ static int sctp_setsockopt_maxseg(struct sock *sk, char __user *optval, unsigned
> >
> > if (asoc) {
> > if (val == 0) {
> > + struct sctp_af *af = sp->pf->af;
> > val = asoc->pathmtu;
> > - val -= sp->pf->af->net_header_len;
> > + val -= af->ip_options_len(asoc->base.sk);
> > + val -= af->net_header_len;
> > val -= sizeof(struct sctphdr) +
> > sizeof(struct sctp_data_chunk);
> > }
>
> Right below here there is a call to sctp_frag_point(). That function
> also needs this tweak.
>
> Yes, we should simplify all these calculations. I have a patch to use
> sctp_frag_point on where it is currently recalculating it on
> sctp_datamsg_from_user(), but probably should include other places as
> well.
I have no further comments on this patchset other than the above and
LGTM.
Thanks Richard.
Marcelo
^ permalink raw reply
* Re: [PATCH v2 net-next] net: ethernet: ti: cpdma: correct error handling for chan create
From: Grygorii Strashko @ 2017-12-12 17:08 UTC (permalink / raw)
To: Ivan Khoronzhuk; +Cc: netdev, davem, linux-omap, linux-kernel
In-Reply-To: <1513096517-3905-1-git-send-email-ivan.khoronzhuk@linaro.org>
On 12/12/2017 10:35 AM, Ivan Khoronzhuk wrote:
> It's not correct to return NULL when that is actually an error and
> function returns errors in any other wrong case. In the same time,
> the cpsw driver and davinci emac doesn't check error case while
> creating channel and it can miss actual error. Also remove WARNs
> duplicated dev_err msgs.
>
> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
> ---
> drivers/net/ethernet/ti/cpsw.c | 12 +++++++++---
> drivers/net/ethernet/ti/davinci_cpdma.c | 2 +-
> drivers/net/ethernet/ti/davinci_emac.c | 9 +++++++--
> 3 files changed, 17 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
> index a60a378..3c85a08 100644
> --- a/drivers/net/ethernet/ti/cpsw.c
> +++ b/drivers/net/ethernet/ti/cpsw.c
> @@ -3065,10 +3065,16 @@ static int cpsw_probe(struct platform_device *pdev)
> }
>
> cpsw->txv[0].ch = cpdma_chan_create(cpsw->dma, 0, cpsw_tx_handler, 0);
> + if (IS_ERR(cpsw->txv[0].ch)) {
> + dev_err(priv->dev, "error initializing tx dma channel\n");
> + ret = PTR_ERR(cpsw->txv[0].ch);
> + goto clean_dma_ret;
> + }
> +
> cpsw->rxv[0].ch = cpdma_chan_create(cpsw->dma, 0, cpsw_rx_handler, 1);
> - if (WARN_ON(!cpsw->rxv[0].ch || !cpsw->txv[0].ch)) {
> - dev_err(priv->dev, "error initializing dma channels\n");
> - ret = -ENOMEM;
> + if (IS_ERR(cpsw->rxv[0].ch)) {
> + dev_err(priv->dev, "error initializing rx dma channel\n");
> + ret = PTR_ERR(cpsw->rxv[0].ch);
> goto clean_dma_ret;
> }
>
> diff --git a/drivers/net/ethernet/ti/davinci_cpdma.c b/drivers/net/ethernet/ti/davinci_cpdma.c
> index e4d6edf..6f9173f 100644
> --- a/drivers/net/ethernet/ti/davinci_cpdma.c
> +++ b/drivers/net/ethernet/ti/davinci_cpdma.c
> @@ -893,7 +893,7 @@ struct cpdma_chan *cpdma_chan_create(struct cpdma_ctlr *ctlr, int chan_num,
> chan_num = rx_type ? rx_chan_num(chan_num) : tx_chan_num(chan_num);
>
> if (__chan_linear(chan_num) >= ctlr->num_chan)
> - return NULL;
> + return ERR_PTR(-EINVAL);
>
> chan = devm_kzalloc(ctlr->dev, sizeof(*chan), GFP_KERNEL);
> if (!chan)
> diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c
> index f58c0c6..3d4af64 100644
> --- a/drivers/net/ethernet/ti/davinci_emac.c
> +++ b/drivers/net/ethernet/ti/davinci_emac.c
> @@ -1870,10 +1870,15 @@ static int davinci_emac_probe(struct platform_device *pdev)
>
> priv->txchan = cpdma_chan_create(priv->dma, EMAC_DEF_TX_CH,
> emac_tx_handler, 0);
> + if (WARN_ON(IS_ERR(priv->txchan))) {
So, logically WARN_ON() should be removed in davinci_emac.c also. Right?
> + rc = PTR_ERR(priv->txchan);
> + goto no_cpdma_chan;
> + }
> +
> priv->rxchan = cpdma_chan_create(priv->dma, EMAC_DEF_RX_CH,
> emac_rx_handler, 1);
> - if (WARN_ON(!priv->txchan || !priv->rxchan)) {
> - rc = -ENOMEM;
> + if (WARN_ON(IS_ERR(priv->rxchan))) {
> + rc = PTR_ERR(priv->rxchan);
> goto no_cpdma_chan;
> }
>
>
--
regards,
-grygorii
^ permalink raw reply
* Re: [PATCH net-next v5 1/2] net: add support for Cavium PTP coprocessor
From: Richard Cochran @ 2017-12-12 17:12 UTC (permalink / raw)
To: Aleksey Makarov
Cc: netdev, linux-arm-kernel, linux-kernel, Goutham, Sunil,
Radoslaw Biernacki, Robert Richter, David Daney,
Philippe Ombredanne
In-Reply-To: <d1e2faeb-ba5e-f324-efb5-da64e4b3ced3@cavium.com>
On Tue, Dec 12, 2017 at 12:41:35PM +0300, Aleksey Makarov wrote:
> If ptp_clock_register() returns NULL, the device is still paired with the driver,
> but the driver is not registered in the PTP core. When ethernet driver needs
> the reference to this cavium PTP driver, it calls cavium_ptp_get() that checks
> if ptp->ptp_clock is NULL and, if so, returns -ENODEV.
The pointer clock->ptp_clock can be NULL.
Yet you de-reference it here:
> +static void cavium_ptp_remove(struct pci_dev *pdev)
> +{
> + struct cavium_ptp *clock = pci_get_drvdata(pdev);
> + u64 clock_cfg;
> +
> + pci_set_drvdata(pdev, NULL);
> +
> + ptp_clock_unregister(clock->ptp_clock);
> +
> + clock_cfg = readq(clock->reg_base + PTP_CLOCK_CFG);
> + clock_cfg &= ~PTP_CLOCK_CFG_PTP_EN;
> + writeq(clock_cfg, clock->reg_base + PTP_CLOCK_CFG);
> +}
and here:
> +static inline int cavium_ptp_clock_index(struct cavium_ptp *clock)
> +{
> + return ptp_clock_index(clock->ptp_clock);
> +}
That needs to be fixed.
Thanks,
Richard
^ permalink raw reply
* [PATCHv2 0/3] Socionext Synquacer NETSEC driver
From: jassisinghbrar @ 2017-12-12 17:14 UTC (permalink / raw)
To: netdev, devicetree
Cc: davem, arnd.bergmann, ard.biesheuvel, robh+dt, mark.rutland,
Jassi Brar
From: Jassi Brar <jaswinder.singh@linaro.org>
Hi,
Changes since v1
# Switched from using memremap to ioremap
# Implemented ndo_do_ioctl callback
# Defined optional 'dma-coherent' DT property
Jassi Brar (3):
dt-bindings: net: Add DT bindings for Socionext Netsec
net: socionext: Add Synquacer NetSec driver
MAINTAINERS: Add entry for Socionext ethernet driver
.../devicetree/bindings/net/socionext-netsec.txt | 43 +
MAINTAINERS | 7 +
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/socionext/Kconfig | 29 +
drivers/net/ethernet/socionext/Makefile | 1 +
drivers/net/ethernet/socionext/netsec.c | 1826 ++++++++++++++++++++
7 files changed, 1908 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/socionext-netsec.txt
create mode 100644 drivers/net/ethernet/socionext/Kconfig
create mode 100644 drivers/net/ethernet/socionext/Makefile
create mode 100644 drivers/net/ethernet/socionext/netsec.c
--
2.7.4
^ permalink raw reply
* [PATCHv2 1/3] dt-bindings: net: Add DT bindings for Socionext Netsec
From: jassisinghbrar @ 2017-12-12 17:15 UTC (permalink / raw)
To: netdev, devicetree
Cc: davem, arnd.bergmann, ard.biesheuvel, robh+dt, mark.rutland,
Jassi Brar, Jassi Brar
In-Reply-To: <1513098873-20977-1-git-send-email-jassisinghbrar@gmail.com>
From: Jassi Brar <jassisinghbrar@gmail.com>
This patch adds documentation for Device-Tree bindings for the
Socionext NetSec Controller driver.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
---
.../devicetree/bindings/net/socionext-netsec.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/socionext-netsec.txt
diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt
new file mode 100644
index 0000000..4695969
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt
@@ -0,0 +1,45 @@
+* Socionext NetSec Ethernet Controller IP
+
+Required properties:
+- compatible: Should be "socionext,synquacer-netsec"
+- reg: Address and length of the control register area, followed by the
+ address and length of the EEPROM holding the MAC address and
+ microengine firmware
+- interrupts: Should contain ethernet controller interrupt
+- clocks: phandle to the PHY reference clock, and any other clocks to be
+ switched by runtime_pm
+- clock-names: Required only if more than a single clock is listed in 'clocks'.
+ The PHY reference clock must be named 'phy_refclk'
+- phy-mode: See ethernet.txt file in the same directory
+- phy-handle: phandle to select child phy
+
+Optional properties: (See ethernet.txt file in the same directory)
+- dma-coherent: Boolean property, must only be present if memory
+ accesses performed by the device are cache coherent
+- local-mac-address
+- mac-address
+- max-speed
+- max-frame-size
+
+Required properties for the child phy:
+- reg: phy address
+
+Example:
+ eth0: netsec@522D0000 {
+ compatible = "socionext,synquacer-netsec";
+ reg = <0 0x522D0000 0x0 0x10000>, <0 0x10000000 0x0 0x10000>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_netsec>;
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ max-frame-size = <9000>;
+ phy-handle = <ðphy0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
--
2.7.4
^ permalink raw reply related
* [PATCHv2 2/3] net: socionext: Add Synquacer NetSec driver
From: jassisinghbrar-Re5JQEeQqe8AvxtiuMwx3w @ 2017-12-12 17:15 UTC (permalink / raw)
To: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: davem-fT/PcQaiUtIeIZ0/mPfg9Q,
arnd.bergmann-QSEj5FYQhm4dnm+yROfE0A,
ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
Jassi Brar
In-Reply-To: <1513098873-20977-1-git-send-email-jassisinghbrar-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
From: Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
This driver adds support for Socionext "netsec" IP Gigabit
Ethernet + PHY IP used in the Synquacer SC2A11 SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/socionext/Kconfig | 29 +
drivers/net/ethernet/socionext/Makefile | 1 +
drivers/net/ethernet/socionext/netsec.c | 1826 +++++++++++++++++++++++++++++++
5 files changed, 1858 insertions(+)
create mode 100644 drivers/net/ethernet/socionext/Kconfig
create mode 100644 drivers/net/ethernet/socionext/Makefile
create mode 100644 drivers/net/ethernet/socionext/netsec.c
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index c604213..d50519e 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -170,6 +170,7 @@ source "drivers/net/ethernet/sis/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
source "drivers/net/ethernet/sgi/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
+source "drivers/net/ethernet/socionext/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/tehuti/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 39f62733..6cf5ade 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_SFC) += sfc/
obj-$(CONFIG_SFC_FALCON) += sfc/falcon/
obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
+obj-$(CONFIG_NET_VENDOR_SOCIONEXT) += socionext/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/
diff --git a/drivers/net/ethernet/socionext/Kconfig b/drivers/net/ethernet/socionext/Kconfig
new file mode 100644
index 0000000..4601c2f
--- /dev/null
+++ b/drivers/net/ethernet/socionext/Kconfig
@@ -0,0 +1,29 @@
+#
+# Socionext Network device configuration
+#
+
+config NET_VENDOR_SOCIONEXT
+ bool "Socionext devices"
+ default y
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ the questions about Socionext cards. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_SOCIONEXT
+
+config SNI_NETSEC
+ tristate "NETSEC Driver Support"
+ depends on (ARCH_SYNQUACER || COMPILE_TEST) && OF
+ select PHYLIB
+ select MII
+help
+ Enable to add support for the SocioNext NetSec Gigabit Ethernet
+ controller + PHY, as found on the Synquacer SC2A11 SoC
+
+ To compile this driver as a module, choose M here: the module will be
+ called netsec. If unsure, say N.
+
+endif # NET_VENDOR_SOCIONEXT
diff --git a/drivers/net/ethernet/socionext/Makefile b/drivers/net/ethernet/socionext/Makefile
new file mode 100644
index 0000000..9505923
--- /dev/null
+++ b/drivers/net/ethernet/socionext/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_SNI_NETSEC) += netsec.o
diff --git a/drivers/net/ethernet/socionext/netsec.c b/drivers/net/ethernet/socionext/netsec.c
new file mode 100644
index 0000000..4472303a
--- /dev/null
+++ b/drivers/net/ethernet/socionext/netsec.c
@@ -0,0 +1,1826 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/types.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/acpi.h>
+#include <linux/of_mdio.h>
+#include <linux/etherdevice.h>
+#include <linux/interrupt.h>
+
+#include <net/tcp.h>
+#include <net/ip6_checksum.h>
+
+#define NETSEC_REG_SOFT_RST 0x104
+#define NETSEC_REG_COM_INIT 0x120
+
+#define NETSEC_REG_TOP_STATUS 0x200
+#define NETSEC_IRQ_RX BIT(1)
+#define NETSEC_IRQ_TX BIT(0)
+
+#define NETSEC_REG_TOP_INTEN 0x204
+#define NETSEC_REG_INTEN_SET 0x234
+#define NETSEC_REG_INTEN_CLR 0x238
+
+#define NETSEC_REG_NRM_TX_STATUS 0x400
+#define NETSEC_REG_NRM_TX_INTEN 0x404
+#define NETSEC_REG_NRM_TX_INTEN_SET 0x428
+#define NETSEC_REG_NRM_TX_INTEN_CLR 0x42c
+#define NRM_TX_ST_NTOWNR BIT(17)
+#define NRM_TX_ST_TR_ERR BIT(16)
+#define NRM_TX_ST_TXDONE BIT(15)
+#define NRM_TX_ST_TMREXP BIT(14)
+
+#define NETSEC_REG_NRM_RX_STATUS 0x440
+#define NETSEC_REG_NRM_RX_INTEN 0x444
+#define NETSEC_REG_NRM_RX_INTEN_SET 0x468
+#define NETSEC_REG_NRM_RX_INTEN_CLR 0x46c
+#define NRM_RX_ST_RC_ERR BIT(16)
+#define NRM_RX_ST_PKTCNT BIT(15)
+#define NRM_RX_ST_TMREXP BIT(14)
+
+#define NETSEC_REG_PKT_CMD_BUF 0xd0
+
+#define NETSEC_REG_CLK_EN 0x100
+
+#define NETSEC_REG_PKT_CTRL 0x140
+
+#define NETSEC_REG_DMA_TMR_CTRL 0x20c
+#define NETSEC_REG_F_TAIKI_MC_VER 0x22c
+#define NETSEC_REG_F_TAIKI_VER 0x230
+#define NETSEC_REG_DMA_HM_CTRL 0x214
+#define NETSEC_REG_DMA_MH_CTRL 0x220
+#define NETSEC_REG_ADDR_DIS_CORE 0x218
+#define NETSEC_REG_DMAC_HM_CMD_BUF 0x210
+#define NETSEC_REG_DMAC_MH_CMD_BUF 0x21c
+
+#define NETSEC_REG_NRM_TX_PKTCNT 0x410
+
+#define NETSEC_REG_NRM_TX_DONE_PKTCNT 0x414
+#define NETSEC_REG_NRM_TX_DONE_TXINT_PKTCNT 0x418
+
+#define NETSEC_REG_NRM_TX_TMR 0x41c
+
+#define NETSEC_REG_NRM_RX_PKTCNT 0x454
+#define NETSEC_REG_NRM_RX_RXINT_PKTCNT 0x458
+#define NETSEC_REG_NRM_TX_TXINT_TMR 0x420
+#define NETSEC_REG_NRM_RX_RXINT_TMR 0x460
+
+#define NETSEC_REG_NRM_RX_TMR 0x45c
+
+#define NETSEC_REG_NRM_TX_DESC_START_UP 0x434
+#define NETSEC_REG_NRM_TX_DESC_START_LW 0x408
+#define NETSEC_REG_NRM_RX_DESC_START_UP 0x474
+#define NETSEC_REG_NRM_RX_DESC_START_LW 0x448
+
+#define NETSEC_REG_NRM_TX_CONFIG 0x430
+#define NETSEC_REG_NRM_RX_CONFIG 0x470
+
+#define MAC_REG_STATUS 0x1024
+#define MAC_REG_DATA 0x11c0
+#define MAC_REG_CMD 0x11c4
+#define MAC_REG_FLOW_TH 0x11cc
+#define MAC_REG_INTF_SEL 0x11d4
+#define MAC_REG_DESC_INIT 0x11fc
+#define MAC_REG_DESC_SOFT_RST 0x1204
+#define NETSEC_REG_MODE_TRANS_COMP_STATUS 0x500
+
+#define GMAC_REG_MCR 0x0000
+#define GMAC_REG_MFFR 0x0004
+#define GMAC_REG_GAR 0x0010
+#define GMAC_REG_GDR 0x0014
+#define GMAC_REG_FCR 0x0018
+#define GMAC_REG_BMR 0x1000
+#define GMAC_REG_RDLAR 0x100c
+#define GMAC_REG_TDLAR 0x1010
+#define GMAC_REG_OMR 0x1018
+
+#define MHZ(n) ((n) * 1000 * 1000)
+
+#define NETSEC_TX_SHIFT_OWN_FIELD 31
+#define NETSEC_TX_SHIFT_LD_FIELD 30
+#define NETSEC_TX_SHIFT_DRID_FIELD 24
+#define NETSEC_TX_SHIFT_PT_FIELD 21
+#define NETSEC_TX_SHIFT_TDRID_FIELD 16
+#define NETSEC_TX_SHIFT_CC_FIELD 15
+#define NETSEC_TX_SHIFT_FS_FIELD 9
+#define NETSEC_TX_LAST 8
+#define NETSEC_TX_SHIFT_CO 7
+#define NETSEC_TX_SHIFT_SO 6
+#define NETSEC_TX_SHIFT_TRS_FIELD 4
+
+#define NETSEC_RX_PKT_OWN_FIELD 31
+#define NETSEC_RX_PKT_LD_FIELD 30
+#define NETSEC_RX_PKT_SDRID_FIELD 24
+#define NETSEC_RX_PKT_FR_FIELD 23
+#define NETSEC_RX_PKT_ER_FIELD 21
+#define NETSEC_RX_PKT_ERR_FIELD 16
+#define NETSEC_RX_PKT_TDRID_FIELD 12
+#define NETSEC_RX_PKT_FS_FIELD 9
+#define NETSEC_RX_PKT_LS_FIELD 8
+#define NETSEC_RX_PKT_CO_FIELD 6
+
+#define NETSEC_RX_PKT_ERR_MASK 3
+
+#define NETSEC_MAX_TX_PKT_LEN 1518
+#define NETSEC_MAX_TX_JUMBO_PKT_LEN 9018
+
+#define NETSEC_RING_GMAC 15
+#define NETSEC_RING_MAX 2
+
+#define NETSEC_TCP_SEG_LEN_MAX 1460
+#define NETSEC_TCP_JUMBO_SEG_LEN_MAX 8960
+
+#define NETSEC_RX_CKSUM_NOTAVAIL 0
+#define NETSEC_RX_CKSUM_OK 1
+#define NETSEC_RX_CKSUM_NG 2
+
+#define NETSEC_TOP_IRQ_REG_CODE_LOAD_END BIT(20)
+#define NETSEC_IRQ_TRANSITION_COMPLETE BIT(4)
+
+#define NETSEC_MODE_TRANS_COMP_IRQ_N2T BIT(20)
+#define NETSEC_MODE_TRANS_COMP_IRQ_T2N BIT(19)
+
+#define NETSEC_INT_PKTCNT_MAX 2047
+
+#define NETSEC_FLOW_START_TH_MAX 95
+#define NETSEC_FLOW_STOP_TH_MAX 95
+#define NETSEC_FLOW_PAUSE_TIME_MIN 5
+
+#define NETSEC_CLK_EN_REG_DOM_ALL 0x3f
+
+#define NETSEC_PKT_CTRL_REG_MODE_NRM BIT(28)
+#define NETSEC_PKT_CTRL_REG_EN_JUMBO BIT(27)
+#define NETSEC_PKT_CTRL_REG_LOG_CHKSUM_ER BIT(3)
+#define NETSEC_PKT_CTRL_REG_LOG_HD_INCOMPLETE BIT(2)
+#define NETSEC_PKT_CTRL_REG_LOG_HD_ER BIT(1)
+#define NETSEC_PKT_CTRL_REG_DRP_NO_MATCH BIT(0)
+
+#define NETSEC_CLK_EN_REG_DOM_G BIT(5)
+#define NETSEC_CLK_EN_REG_DOM_C BIT(1)
+#define NETSEC_CLK_EN_REG_DOM_D BIT(0)
+
+#define NETSEC_COM_INIT_REG_DB BIT(2)
+#define NETSEC_COM_INIT_REG_CLS BIT(1)
+#define NETSEC_COM_INIT_REG_ALL (NETSEC_COM_INIT_REG_CLS | \
+ NETSEC_COM_INIT_REG_DB)
+
+#define NETSEC_SOFT_RST_REG_RESET 0
+#define NETSEC_SOFT_RST_REG_RUN BIT(31)
+
+#define NETSEC_DMA_CTRL_REG_STOP 1
+#define MH_CTRL__MODE_TRANS BIT(20)
+
+#define NETSEC_GMAC_CMD_ST_READ 0
+#define NETSEC_GMAC_CMD_ST_WRITE BIT(28)
+#define NETSEC_GMAC_CMD_ST_BUSY BIT(31)
+
+#define NETSEC_GMAC_BMR_REG_COMMON 0x00412080
+#define NETSEC_GMAC_BMR_REG_RESET 0x00020181
+#define NETSEC_GMAC_BMR_REG_SWR 0x00000001
+
+#define NETSEC_GMAC_OMR_REG_ST BIT(13)
+#define NETSEC_GMAC_OMR_REG_SR BIT(1)
+
+#define NETSEC_GMAC_MCR_REG_IBN BIT(30)
+#define NETSEC_GMAC_MCR_REG_CST BIT(25)
+#define NETSEC_GMAC_MCR_REG_JE BIT(20)
+#define NETSEC_MCR_PS BIT(15)
+#define NETSEC_GMAC_MCR_REG_FES BIT(14)
+#define NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON 0x0000280c
+#define NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON 0x0001a00c
+
+#define NETSEC_FCR_RFE BIT(2)
+#define NETSEC_FCR_TFE BIT(1)
+
+#define NETSEC_GMAC_GAR_REG_GW BIT(1)
+#define NETSEC_GMAC_GAR_REG_GB BIT(0)
+
+#define NETSEC_GMAC_GAR_REG_SHIFT_PA 11
+#define NETSEC_GMAC_GAR_REG_SHIFT_GR 6
+#define GMAC_REG_SHIFT_CR_GAR 2
+
+#define NETSEC_GMAC_GAR_REG_CR_25_35_MHZ 2
+#define NETSEC_GMAC_GAR_REG_CR_35_60_MHZ 3
+#define NETSEC_GMAC_GAR_REG_CR_60_100_MHZ 0
+#define NETSEC_GMAC_GAR_REG_CR_100_150_MHZ 1
+#define NETSEC_GMAC_GAR_REG_CR_150_250_MHZ 4
+#define NETSEC_GMAC_GAR_REG_CR_250_300_MHZ 5
+
+#define NETSEC_GMAC_RDLAR_REG_COMMON 0x18000
+#define NETSEC_GMAC_TDLAR_REG_COMMON 0x1c000
+
+#define NETSEC_REG_NETSEC_VER_F_TAIKI 0x50000
+
+#define NETSEC_REG_DESC_RING_CONFIG_CFG_UP BIT(31)
+#define NETSEC_REG_DESC_RING_CONFIG_CH_RST BIT(30)
+#define NETSEC_REG_DESC_TMR_MODE 4
+#define NETSEC_REG_DESC_ENDIAN 0
+
+#define NETSEC_MAC_DESC_SOFT_RST_SOFT_RST 1
+#define NETSEC_MAC_DESC_INIT_REG_INIT 1
+
+#define NETSEC_EEPROM_MAC_ADDRESS 0x00
+#define NETSEC_EEPROM_HM_ME_ADDRESS_H 0x08
+#define NETSEC_EEPROM_HM_ME_ADDRESS_L 0x0C
+#define NETSEC_EEPROM_HM_ME_SIZE 0x10
+#define NETSEC_EEPROM_MH_ME_ADDRESS_H 0x14
+#define NETSEC_EEPROM_MH_ME_ADDRESS_L 0x18
+#define NETSEC_EEPROM_MH_ME_SIZE 0x1C
+#define NETSEC_EEPROM_PKT_ME_ADDRESS 0x20
+#define NETSEC_EEPROM_PKT_ME_SIZE 0x24
+
+#define DESC_NUM 128
+#define NAPI_BUDGET (DESC_NUM / 2)
+
+#define DESC_SZ sizeof(struct netsec_de)
+
+#define NETSEC_F_NETSEC_VER_MAJOR_NUM(x) ((x) & 0xffff0000)
+
+enum ring_id {
+ NETSEC_RING_TX = 0,
+ NETSEC_RING_RX
+};
+
+struct netsec_desc {
+ struct sk_buff *skb;
+ dma_addr_t dma_addr;
+ void *addr;
+ u16 len;
+};
+
+struct netsec_desc_ring {
+ phys_addr_t desc_phys;
+ struct netsec_desc *desc;
+ void *vaddr;
+ u16 pkt_cnt;
+ u16 head, tail;
+};
+
+struct netsec_priv {
+ struct netsec_desc_ring desc_ring[NETSEC_RING_MAX];
+ struct ethtool_coalesce et_coalesce;
+ spinlock_t reglock; /* protect reg access */
+ struct napi_struct napi;
+ phy_interface_t phy_interface;
+ struct net_device *ndev;
+ struct device_node *phy_np;
+ struct phy_device *phydev;
+ struct mii_bus *mii_bus;
+ void __iomem *ioaddr;
+ void __iomem *eeprom_base;
+ struct device *dev;
+ struct clk *clk[3];
+ u32 msg_enable;
+ u32 freq;
+ int clock_count;
+ bool rx_cksum_offload_flag;
+};
+
+struct netsec_de { /* Netsec Descriptor layout */
+ u32 attr;
+ u32 data_buf_addr_up;
+ u32 data_buf_addr_lw;
+ u32 buf_len_info;
+};
+
+struct netsec_tx_pkt_ctrl {
+ u16 tcp_seg_len;
+ bool tcp_seg_offload_flag;
+ bool cksum_offload_flag;
+};
+
+struct netsec_rx_pkt_info {
+ int rx_cksum_result;
+ int err_code;
+ bool err_flag;
+};
+
+static inline void netsec_write(struct netsec_priv *priv,
+ u32 reg_addr, u32 val)
+{
+ writel(val, priv->ioaddr + reg_addr);
+}
+
+static inline u32 netsec_read(struct netsec_priv *priv, u32 reg_addr)
+{
+ return readl(priv->ioaddr + reg_addr);
+}
+
+#define DRING_TAIL(r) ((r)->tail)
+
+#define DRING_HEAD(r) ((r)->head)
+
+#define MOVE_TAIL(r) do { \
+ if (++(r)->tail == DESC_NUM) \
+ (r)->tail = 0; \
+ } while (0)
+
+#define MOVE_HEAD(r) do { \
+ if (++(r)->head == DESC_NUM) \
+ (r)->head = 0; \
+ } while (0)
+
+#define JUMP_HEAD(r, n) do { \
+ int i; \
+ for (i = 0; i < (n); i++) \
+ MOVE_HEAD(r); \
+ } while (0)
+
+static inline int available_descs(struct netsec_desc_ring *r)
+{
+ int filled;
+
+ if ((r)->head >= (r)->tail)
+ filled = (r)->head - (r)->tail;
+ else
+ filled = (r)->head + DESC_NUM - (r)->tail;
+
+ return DESC_NUM - filled;
+}
+
+/*************************************************************/
+/*********************** MDIO BUS OPS ************************/
+/*************************************************************/
+
+#define TIMEOUT_SPINS_MAC 1000
+#define TIMEOUT_SECONDARY_MS_MAC 100
+
+static u32 netsec_clk_type(u32 freq)
+{
+ if (freq < MHZ(35))
+ return NETSEC_GMAC_GAR_REG_CR_25_35_MHZ;
+ if (freq < MHZ(60))
+ return NETSEC_GMAC_GAR_REG_CR_35_60_MHZ;
+ if (freq < MHZ(100))
+ return NETSEC_GMAC_GAR_REG_CR_60_100_MHZ;
+ if (freq < MHZ(150))
+ return NETSEC_GMAC_GAR_REG_CR_100_150_MHZ;
+ if (freq < MHZ(250))
+ return NETSEC_GMAC_GAR_REG_CR_150_250_MHZ;
+
+ return NETSEC_GMAC_GAR_REG_CR_250_300_MHZ;
+}
+
+static int netsec_wait_while_busy(struct netsec_priv *priv, u32 addr, u32 mask)
+{
+ u32 timeout = TIMEOUT_SPINS_MAC;
+
+ while (--timeout && netsec_read(priv, addr) & mask)
+ cpu_relax();
+ if (timeout)
+ return 0;
+
+ timeout = TIMEOUT_SECONDARY_MS_MAC;
+ while (--timeout && netsec_read(priv, addr) & mask)
+ usleep_range(1000, 2000);
+
+ if (timeout)
+ return 0;
+
+ netdev_WARN(priv->ndev, "%s: timeout\n", __func__);
+
+ return -ETIMEDOUT;
+}
+
+static int netsec_mac_write(struct netsec_priv *priv, u32 addr, u32 value)
+{
+ netsec_write(priv, MAC_REG_DATA, value);
+ netsec_write(priv, MAC_REG_CMD, addr | NETSEC_GMAC_CMD_ST_WRITE);
+ return netsec_wait_while_busy(priv,
+ MAC_REG_CMD, NETSEC_GMAC_CMD_ST_BUSY);
+}
+
+static int netsec_mac_read(struct netsec_priv *priv, u32 addr, u32 *read)
+{
+ int ret;
+
+ netsec_write(priv, MAC_REG_CMD, addr | NETSEC_GMAC_CMD_ST_READ);
+ ret = netsec_wait_while_busy(priv,
+ MAC_REG_CMD, NETSEC_GMAC_CMD_ST_BUSY);
+ if (ret)
+ return ret;
+
+ *read = netsec_read(priv, MAC_REG_DATA);
+
+ return 0;
+}
+
+static int netsec_mac_wait_while_busy(struct netsec_priv *priv,
+ u32 addr, u32 mask)
+{
+ u32 timeout = TIMEOUT_SPINS_MAC;
+ int ret, data;
+
+ do {
+ ret = netsec_mac_read(priv, addr, &data);
+ if (ret)
+ break;
+ cpu_relax();
+ } while (--timeout && (data & mask));
+
+ if (timeout)
+ return 0;
+
+ timeout = TIMEOUT_SECONDARY_MS_MAC;
+ do {
+ usleep_range(1000, 2000);
+
+ ret = netsec_mac_read(priv, addr, &data);
+ if (ret)
+ break;
+ cpu_relax();
+ } while (--timeout && (data & mask));
+
+ if (timeout && !ret)
+ return 0;
+
+ netdev_WARN(priv->ndev, "%s: timeout\n", __func__);
+
+ return -ETIMEDOUT;
+}
+
+static int netsec_mac_update_to_phy_state(struct netsec_priv *priv)
+{
+ struct phy_device *phydev = priv->ndev->phydev;
+ u32 value = 0;
+
+ value = phydev->duplex ? NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON :
+ NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON;
+
+ if (phydev->speed != SPEED_1000)
+ value |= NETSEC_MCR_PS;
+
+ if (priv->phy_interface != PHY_INTERFACE_MODE_GMII &&
+ phydev->speed == SPEED_100)
+ value |= NETSEC_GMAC_MCR_REG_FES;
+
+ value |= NETSEC_GMAC_MCR_REG_CST | NETSEC_GMAC_MCR_REG_JE;
+
+ if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII)
+ value |= NETSEC_GMAC_MCR_REG_IBN;
+
+ if (netsec_mac_write(priv, GMAC_REG_MCR, value))
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+static int netsec_phy_write(struct mii_bus *bus,
+ int phy_addr, int reg, u16 val)
+{
+ struct netsec_priv *priv = bus->priv;
+
+ if (netsec_mac_write(priv, GMAC_REG_GDR, val))
+ return -ETIMEDOUT;
+ if (netsec_mac_write(priv, GMAC_REG_GAR,
+ phy_addr << NETSEC_GMAC_GAR_REG_SHIFT_PA |
+ reg << NETSEC_GMAC_GAR_REG_SHIFT_GR |
+ NETSEC_GMAC_GAR_REG_GW | NETSEC_GMAC_GAR_REG_GB |
+ (netsec_clk_type(priv->freq) <<
+ GMAC_REG_SHIFT_CR_GAR)))
+ return -ETIMEDOUT;
+
+ return netsec_mac_wait_while_busy(priv, GMAC_REG_GAR,
+ NETSEC_GMAC_GAR_REG_GB);
+}
+
+static int netsec_phy_read(struct mii_bus *bus, int phy_addr, int reg_addr)
+{
+ struct netsec_priv *priv = bus->priv;
+ u32 data;
+ int ret;
+
+ if (netsec_mac_write(priv, GMAC_REG_GAR, NETSEC_GMAC_GAR_REG_GB |
+ phy_addr << NETSEC_GMAC_GAR_REG_SHIFT_PA |
+ reg_addr << NETSEC_GMAC_GAR_REG_SHIFT_GR |
+ (netsec_clk_type(priv->freq) <<
+ GMAC_REG_SHIFT_CR_GAR)))
+ return -ETIMEDOUT;
+
+ ret = netsec_mac_wait_while_busy(priv, GMAC_REG_GAR,
+ NETSEC_GMAC_GAR_REG_GB);
+ if (ret)
+ return ret;
+
+ ret = netsec_mac_read(priv, GMAC_REG_GDR, &data);
+ if (ret)
+ return ret;
+
+ return data;
+}
+
+/*************************************************************/
+/*********************** ETHTOOL_OPS **************************/
+/*************************************************************/
+
+static void netsec_et_get_drvinfo(struct net_device *net_device,
+ struct ethtool_drvinfo *info)
+{
+ strlcpy(info->driver, "netsec", sizeof(info->driver));
+ strlcpy(info->bus_info, dev_name(net_device->dev.parent),
+ sizeof(info->bus_info));
+}
+
+static int netsec_et_get_coalesce(struct net_device *net_device,
+ struct ethtool_coalesce *et_coalesce)
+{
+ struct netsec_priv *priv = netdev_priv(net_device);
+
+ *et_coalesce = priv->et_coalesce;
+
+ return 0;
+}
+
+static int netsec_et_set_coalesce(struct net_device *net_device,
+ struct ethtool_coalesce *et_coalesce)
+{
+ struct netsec_priv *priv = netdev_priv(net_device);
+
+ priv->et_coalesce = *et_coalesce;
+
+ if (priv->et_coalesce.tx_coalesce_usecs < 50)
+ priv->et_coalesce.tx_coalesce_usecs = 50;
+ if (priv->et_coalesce.tx_max_coalesced_frames < 1)
+ priv->et_coalesce.tx_max_coalesced_frames = 1;
+
+ netsec_write(priv, NETSEC_REG_NRM_TX_DONE_TXINT_PKTCNT,
+ priv->et_coalesce.tx_max_coalesced_frames);
+ netsec_write(priv, NETSEC_REG_NRM_TX_TXINT_TMR,
+ priv->et_coalesce.tx_coalesce_usecs);
+ netsec_write(priv, NETSEC_REG_NRM_TX_INTEN_SET, NRM_TX_ST_TXDONE);
+ netsec_write(priv, NETSEC_REG_NRM_TX_INTEN_SET, NRM_TX_ST_TMREXP);
+
+ if (priv->et_coalesce.rx_coalesce_usecs < 50)
+ priv->et_coalesce.rx_coalesce_usecs = 50;
+ if (priv->et_coalesce.rx_max_coalesced_frames < 1)
+ priv->et_coalesce.rx_max_coalesced_frames = 1;
+
+ netsec_write(priv, NETSEC_REG_NRM_RX_RXINT_PKTCNT,
+ priv->et_coalesce.rx_max_coalesced_frames);
+ netsec_write(priv, NETSEC_REG_NRM_RX_RXINT_TMR,
+ priv->et_coalesce.rx_coalesce_usecs);
+ netsec_write(priv, NETSEC_REG_NRM_RX_INTEN_SET, NRM_RX_ST_PKTCNT);
+ netsec_write(priv, NETSEC_REG_NRM_RX_INTEN_SET, NRM_RX_ST_TMREXP);
+
+ return 0;
+}
+
+static u32 netsec_et_get_msglevel(struct net_device *dev)
+{
+ struct netsec_priv *priv = netdev_priv(dev);
+
+ return priv->msg_enable;
+}
+
+static void netsec_et_set_msglevel(struct net_device *dev, u32 datum)
+{
+ struct netsec_priv *priv = netdev_priv(dev);
+
+ priv->msg_enable = datum;
+}
+
+static const struct ethtool_ops netsec_ethtool_ops = {
+ .get_drvinfo = netsec_et_get_drvinfo,
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_link = ethtool_op_get_link,
+ .get_coalesce = netsec_et_get_coalesce,
+ .set_coalesce = netsec_et_set_coalesce,
+ .get_msglevel = netsec_et_get_msglevel,
+ .set_msglevel = netsec_et_set_msglevel,
+};
+
+/*************************************************************/
+/*********************** NETDEV_OPS **************************/
+/*************************************************************/
+
+static struct sk_buff *netsec_alloc_skb(struct netsec_priv *priv,
+ struct netsec_desc *desc)
+{
+ struct sk_buff *skb;
+
+ if (device_get_dma_attr(priv->dev) == DEV_DMA_COHERENT) {
+ skb = netdev_alloc_skb_ip_align(priv->ndev, desc->len);
+ } else {
+ desc->len = L1_CACHE_ALIGN(desc->len);
+ skb = netdev_alloc_skb(priv->ndev, desc->len);
+ }
+ if (!skb)
+ return NULL;
+
+ desc->addr = skb->data;
+ desc->dma_addr = dma_map_single(priv->dev, desc->addr, desc->len,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(priv->dev, desc->dma_addr)) {
+ dev_kfree_skb_any(skb);
+ return NULL;
+ }
+ return skb;
+}
+
+static void netsec_set_rx_de(struct netsec_priv *priv,
+ struct netsec_desc_ring *dring, u16 idx,
+ const struct netsec_desc *desc,
+ struct sk_buff *skb)
+{
+ struct netsec_de *de = dring->vaddr + DESC_SZ * idx;
+ u32 attr = (1 << NETSEC_RX_PKT_OWN_FIELD) |
+ (1 << NETSEC_RX_PKT_FS_FIELD) |
+ (1 << NETSEC_RX_PKT_LS_FIELD);
+
+ if (idx == DESC_NUM - 1)
+ attr |= (1 << NETSEC_RX_PKT_LD_FIELD);
+
+ de->data_buf_addr_up = upper_32_bits(desc->dma_addr);
+ de->data_buf_addr_lw = lower_32_bits(desc->dma_addr);
+ de->buf_len_info = desc->len;
+ de->attr = attr;
+ dma_wmb();
+
+ dring->desc[idx].dma_addr = desc->dma_addr;
+ dring->desc[idx].addr = desc->addr;
+ dring->desc[idx].len = desc->len;
+ dring->desc[idx].skb = skb;
+}
+
+static struct sk_buff *netsec_get_rx_de(struct netsec_priv *priv,
+ struct netsec_desc_ring *dring,
+ u16 idx,
+ struct netsec_rx_pkt_info *rxpi,
+ struct netsec_desc *desc, u16 *len)
+{
+ struct netsec_de de = {};
+
+ memcpy(&de, dring->vaddr + DESC_SZ * idx, DESC_SZ);
+
+ *len = de.buf_len_info >> 16;
+
+ rxpi->err_flag = (de.attr >> NETSEC_RX_PKT_ER_FIELD) & 1;
+ rxpi->rx_cksum_result = (de.attr >> NETSEC_RX_PKT_CO_FIELD) & 3;
+ rxpi->err_code = (de.attr >> NETSEC_RX_PKT_ERR_FIELD) &
+ NETSEC_RX_PKT_ERR_MASK;
+ *desc = dring->desc[idx];
+ return desc->skb;
+}
+
+static struct sk_buff *netsec_get_rx_pkt_data(struct netsec_priv *priv,
+ struct netsec_rx_pkt_info *rxpi,
+ struct netsec_desc *desc,
+ u16 *len)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_RX];
+ struct sk_buff *tmp_skb, *skb = NULL;
+ struct netsec_desc td;
+ int tail;
+
+ *rxpi = (struct netsec_rx_pkt_info){};
+
+ td.len = priv->ndev->mtu + 22;
+
+ tmp_skb = netsec_alloc_skb(priv, &td);
+
+ dma_rmb();
+
+ tail = DRING_TAIL(dring);
+
+ if (!tmp_skb) {
+ netsec_set_rx_de(priv, dring, tail, &dring->desc[tail],
+ dring->desc[tail].skb);
+ } else {
+ skb = netsec_get_rx_de(priv, dring, tail, rxpi, desc, len);
+ netsec_set_rx_de(priv, dring, tail, &td, tmp_skb);
+ }
+
+ MOVE_TAIL(dring);
+ dring->pkt_cnt--;
+
+ return skb;
+}
+
+static int netsec_clean_tx_dring(struct netsec_priv *priv, int budget)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_TX];
+ unsigned int pkts, bytes;
+
+ dring->pkt_cnt += netsec_read(priv, NETSEC_REG_NRM_TX_DONE_PKTCNT);
+
+ if (dring->pkt_cnt < budget)
+ budget = dring->pkt_cnt;
+
+ pkts = 0;
+ bytes = 0;
+
+ while (pkts < budget) {
+ struct netsec_desc *desc;
+ struct netsec_de *entry;
+ int tail, eop;
+
+ tail = DRING_TAIL(dring);
+ MOVE_TAIL(dring);
+
+ desc = &dring->desc[tail];
+ entry = dring->vaddr + DESC_SZ * tail;
+
+ eop = (entry->attr >> NETSEC_TX_LAST) & 1;
+
+ dma_unmap_single(priv->dev, desc->dma_addr, desc->len,
+ DMA_TO_DEVICE);
+ if (eop) {
+ pkts++;
+ bytes += desc->skb->len;
+ dev_kfree_skb(desc->skb);
+ }
+ *desc = (struct netsec_desc){};
+ }
+ dring->pkt_cnt -= budget;
+
+ priv->ndev->stats.tx_packets += budget;
+ priv->ndev->stats.tx_bytes += bytes;
+
+ netdev_completed_queue(priv->ndev, budget, bytes);
+
+ return budget;
+}
+
+static int netsec_process_tx(struct netsec_priv *priv, int budget)
+{
+ struct net_device *ndev = priv->ndev;
+ int new, done = 0;
+
+ do {
+ new = netsec_clean_tx_dring(priv, budget);
+ done += new;
+ budget -= new;
+ } while (new);
+
+ if (done && netif_queue_stopped(ndev))
+ netif_wake_queue(ndev);
+
+ return done;
+}
+
+static int netsec_process_rx(struct netsec_priv *priv, int budget)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_RX];
+ struct net_device *ndev = priv->ndev;
+ struct netsec_rx_pkt_info rx_info;
+ int done = 0, rx_num = 0;
+ struct netsec_desc desc;
+ struct sk_buff *skb;
+ u16 len;
+
+ while (done < budget) {
+ if (!rx_num) {
+ rx_num = netsec_read(priv, NETSEC_REG_NRM_RX_PKTCNT);
+ dring->pkt_cnt += rx_num;
+ JUMP_HEAD(dring, rx_num);
+
+ rx_num = dring->pkt_cnt;
+ if (!rx_num)
+ break;
+ }
+ done++;
+ rx_num--;
+ skb = netsec_get_rx_pkt_data(priv, &rx_info, &desc, &len);
+ if (unlikely(!skb) || rx_info.err_flag) {
+ netif_err(priv, drv, priv->ndev,
+ "%s: rx fail err(%d)\n",
+ __func__, rx_info.err_code);
+ ndev->stats.rx_dropped++;
+ continue;
+ }
+
+ dma_unmap_single(priv->dev, desc.dma_addr, desc.len,
+ DMA_FROM_DEVICE);
+ skb_put(skb, len);
+ skb->protocol = eth_type_trans(skb, priv->ndev);
+
+ if (priv->rx_cksum_offload_flag &&
+ rx_info.rx_cksum_result == NETSEC_RX_CKSUM_OK)
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+ if (napi_gro_receive(&priv->napi, skb) != GRO_DROP) {
+ ndev->stats.rx_packets++;
+ ndev->stats.rx_bytes += len;
+ }
+ }
+
+ return done;
+}
+
+static int netsec_napi_poll(struct napi_struct *napi, int budget)
+{
+ struct netsec_priv *priv;
+ struct net_device *ndev;
+ int tx, rx, done, todo;
+
+ priv = container_of(napi, struct netsec_priv, napi);
+ ndev = priv->ndev;
+
+ todo = budget;
+ do {
+ if (!todo)
+ break;
+
+ tx = netsec_process_tx(priv, todo);
+ todo -= tx;
+
+ if (!todo)
+ break;
+
+ rx = netsec_process_rx(priv, todo);
+ todo -= rx;
+ } while (rx || tx);
+
+ done = budget - todo;
+
+ if (done < budget && napi_complete_done(napi, done)) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->reglock, flags);
+ netsec_write(priv, NETSEC_REG_INTEN_SET,
+ NETSEC_IRQ_RX | NETSEC_IRQ_TX);
+ spin_unlock_irqrestore(&priv->reglock, flags);
+ }
+
+ return done;
+}
+
+static void netsec_set_tx_de(struct netsec_priv *priv,
+ struct netsec_desc_ring *dring,
+ const struct netsec_tx_pkt_ctrl *tx_ctrl,
+ const struct netsec_desc *desc,
+ struct sk_buff *skb)
+{
+ struct netsec_de *de;
+ int idx = DRING_HEAD(dring);
+ u32 attr;
+
+ de = dring->vaddr + (DESC_SZ * idx);
+
+ attr = (1 << NETSEC_TX_SHIFT_OWN_FIELD) |
+ (1 << NETSEC_TX_SHIFT_PT_FIELD) |
+ (NETSEC_RING_GMAC << NETSEC_TX_SHIFT_TDRID_FIELD) |
+ (1 << NETSEC_TX_SHIFT_FS_FIELD) |
+ (1 << NETSEC_TX_LAST) |
+ (tx_ctrl->cksum_offload_flag << NETSEC_TX_SHIFT_CO) |
+ (tx_ctrl->tcp_seg_offload_flag << NETSEC_TX_SHIFT_SO) |
+ (1 << NETSEC_TX_SHIFT_TRS_FIELD);
+ if (idx == DESC_NUM - 1)
+ attr |= (1 << NETSEC_TX_SHIFT_LD_FIELD);
+
+ de->data_buf_addr_up = upper_32_bits(desc->dma_addr);
+ de->data_buf_addr_lw = lower_32_bits(desc->dma_addr);
+ de->buf_len_info = (tx_ctrl->tcp_seg_len << 16) | desc->len;
+ de->attr = attr;
+ dma_wmb();
+
+ dring->desc[idx] = *desc;
+ dring->desc[idx].skb = skb;
+
+ MOVE_HEAD(dring);
+}
+
+static netdev_tx_t netsec_netdev_start_xmit(struct sk_buff *skb,
+ struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+ struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_TX];
+ struct netsec_tx_pkt_ctrl tx_ctrl = {};
+ struct netsec_desc tx_desc;
+ u16 tso_seg_len = 0;
+
+ /* differentiate between full/emtpy ring */
+ if (available_descs(dring) < 2) {
+ netif_err(priv, drv, priv->ndev, "%s: TxQFull!\n", __func__);
+ netif_stop_queue(priv->ndev);
+ dma_wmb();
+ return NETDEV_TX_BUSY;
+ }
+
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
+ tx_ctrl.cksum_offload_flag = true;
+
+ if (skb_is_gso(skb))
+ tso_seg_len = skb_shinfo(skb)->gso_size;
+
+ if (tso_seg_len > 0) {
+ if (skb->protocol == htons(ETH_P_IP)) {
+ ip_hdr(skb)->tot_len = 0;
+ tcp_hdr(skb)->check =
+ ~tcp_v4_check(0, ip_hdr(skb)->saddr,
+ ip_hdr(skb)->daddr, 0);
+ } else {
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check =
+ ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ }
+
+ tx_ctrl.tcp_seg_offload_flag = true;
+ tx_ctrl.tcp_seg_len = tso_seg_len;
+ }
+
+ tx_desc.dma_addr = dma_map_single(priv->dev, skb->data,
+ skb_headlen(skb), DMA_TO_DEVICE);
+ if (dma_mapping_error(priv->dev, tx_desc.dma_addr)) {
+ netif_err(priv, drv, priv->ndev,
+ "%s: DMA mapping failed\n", __func__);
+ ndev->stats.tx_dropped++;
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+ tx_desc.addr = skb->data;
+ tx_desc.len = skb_headlen(skb);
+
+ skb_tx_timestamp(skb);
+ netdev_sent_queue(priv->ndev, skb->len);
+
+ netsec_set_tx_de(priv, dring, &tx_ctrl, &tx_desc, skb);
+ netsec_write(priv, NETSEC_REG_NRM_TX_PKTCNT, 1); /* submit another tx */
+
+ return NETDEV_TX_OK;
+}
+
+static void netsec_uninit_pkt_dring(struct netsec_priv *priv, int id)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[id];
+ struct netsec_desc *desc;
+ u16 idx;
+
+ if (!dring->vaddr || !dring->desc)
+ return;
+
+ for (idx = 0; idx < DESC_NUM; idx++) {
+ desc = &dring->desc[idx];
+ if (!desc->addr)
+ continue;
+
+ dma_unmap_single(priv->dev, desc->dma_addr, desc->len,
+ id == NETSEC_RING_RX ? DMA_FROM_DEVICE :
+ DMA_TO_DEVICE);
+ dev_kfree_skb(desc->skb);
+ }
+
+ memset(dring->desc, 0, sizeof(struct netsec_desc) * DESC_NUM);
+ memset(dring->vaddr, 0, DESC_SZ * DESC_NUM);
+
+ dring->head = 0;
+ dring->tail = 0;
+ dring->pkt_cnt = 0;
+}
+
+static void netsec_free_dring(struct netsec_priv *priv, int id)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[id];
+
+ if (dring->vaddr) {
+ dma_free_coherent(priv->dev, DESC_SZ * DESC_NUM,
+ dring->vaddr, dring->desc_phys);
+ dring->vaddr = NULL;
+ }
+
+ kfree(dring->desc);
+ dring->desc = NULL;
+}
+
+static int netsec_alloc_dring(struct netsec_priv *priv, enum ring_id id)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[id];
+ int ret = 0;
+
+ dring->vaddr = dma_zalloc_coherent(priv->dev, DESC_SZ * DESC_NUM,
+ &dring->desc_phys, GFP_KERNEL);
+ if (!dring->vaddr) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ dring->desc = kzalloc(DESC_NUM * sizeof(*dring->desc), GFP_KERNEL);
+ if (!dring->desc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ return 0;
+err:
+ netsec_free_dring(priv, id);
+
+ return ret;
+}
+
+static int netsec_setup_rx_dring(struct netsec_priv *priv)
+{
+ struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_RX];
+ struct netsec_desc desc;
+ struct sk_buff *skb;
+ int n;
+
+ desc.len = priv->ndev->mtu + 22;
+
+ for (n = 0; n < DESC_NUM; n++) {
+ skb = netsec_alloc_skb(priv, &desc);
+ if (!skb) {
+ netsec_uninit_pkt_dring(priv, NETSEC_RING_RX);
+ return -ENOMEM;
+ }
+ netsec_set_rx_de(priv, dring, n, &desc, skb);
+ }
+
+ return 0;
+}
+
+static int netsec_netdev_load_ucode_region(struct netsec_priv *priv, u32 reg,
+ u32 addr_h, u32 addr_l, u32 size)
+{
+ u64 base = (u64)addr_h << 32 | addr_l;
+ __le32 *ucode;
+ u32 i;
+
+ ucode = memremap(base, size * sizeof(u32), MEMREMAP_WT);
+ if (!ucode)
+ return -ENOMEM;
+
+ for (i = 0; i < size; i++)
+ netsec_write(priv, reg, le32_to_cpu(ucode[i]));
+
+ memunmap(ucode);
+ return 0;
+}
+
+static int netsec_netdev_load_microcode(struct netsec_priv *priv)
+{
+ int err;
+
+ err = netsec_netdev_load_ucode_region(
+ priv, NETSEC_REG_DMAC_HM_CMD_BUF,
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_HM_ME_ADDRESS_H),
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_HM_ME_ADDRESS_L),
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_HM_ME_SIZE));
+ if (err)
+ return err;
+
+ err = netsec_netdev_load_ucode_region(
+ priv, NETSEC_REG_DMAC_MH_CMD_BUF,
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_MH_ME_ADDRESS_H),
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_MH_ME_ADDRESS_L),
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_MH_ME_SIZE));
+ if (err)
+ return err;
+
+ err = netsec_netdev_load_ucode_region(
+ priv, NETSEC_REG_PKT_CMD_BUF,
+ 0,
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_PKT_ME_ADDRESS),
+ le32_to_cpup(priv->eeprom_base + NETSEC_EEPROM_PKT_ME_SIZE));
+ if (err)
+ return err;
+
+ return 0;
+}
+
+static int netsec_reset_hardware(struct netsec_priv *priv)
+{
+ u32 value;
+ int err;
+
+ /* stop DMA engines */
+ if (!netsec_read(priv, NETSEC_REG_ADDR_DIS_CORE)) {
+ netsec_write(priv, NETSEC_REG_DMA_HM_CTRL,
+ NETSEC_DMA_CTRL_REG_STOP);
+ netsec_write(priv, NETSEC_REG_DMA_MH_CTRL,
+ NETSEC_DMA_CTRL_REG_STOP);
+
+ while (netsec_read(priv, NETSEC_REG_DMA_HM_CTRL) &
+ NETSEC_DMA_CTRL_REG_STOP)
+ cpu_relax();
+
+ while (netsec_read(priv, NETSEC_REG_DMA_MH_CTRL) &
+ NETSEC_DMA_CTRL_REG_STOP)
+ cpu_relax();
+ }
+
+ netsec_write(priv, NETSEC_REG_SOFT_RST, NETSEC_SOFT_RST_REG_RESET);
+ netsec_write(priv, NETSEC_REG_SOFT_RST, NETSEC_SOFT_RST_REG_RUN);
+ netsec_write(priv, NETSEC_REG_COM_INIT, NETSEC_COM_INIT_REG_ALL);
+
+ while (netsec_read(priv, NETSEC_REG_COM_INIT) != 0)
+ cpu_relax();
+
+ /* set desc_start addr */
+ netsec_write(priv, NETSEC_REG_NRM_RX_DESC_START_UP,
+ upper_32_bits(priv->desc_ring[NETSEC_RING_RX].desc_phys));
+ netsec_write(priv, NETSEC_REG_NRM_RX_DESC_START_LW,
+ lower_32_bits(priv->desc_ring[NETSEC_RING_RX].desc_phys));
+
+ netsec_write(priv, NETSEC_REG_NRM_TX_DESC_START_UP,
+ upper_32_bits(priv->desc_ring[NETSEC_RING_TX].desc_phys));
+ netsec_write(priv, NETSEC_REG_NRM_TX_DESC_START_LW,
+ lower_32_bits(priv->desc_ring[NETSEC_RING_TX].desc_phys));
+
+ /* set normal tx dring ring config */
+ netsec_write(priv, NETSEC_REG_NRM_TX_CONFIG,
+ 1 << NETSEC_REG_DESC_ENDIAN);
+ netsec_write(priv, NETSEC_REG_NRM_RX_CONFIG,
+ 1 << NETSEC_REG_DESC_ENDIAN);
+
+ err = netsec_netdev_load_microcode(priv);
+ if (err) {
+ netif_err(priv, probe, priv->ndev,
+ "%s: failed to load microcode (%d)\n", __func__, err);
+ return err;
+ }
+
+ /* start DMA engines */
+ netsec_write(priv, NETSEC_REG_DMA_TMR_CTRL, priv->freq / 1000000 - 1);
+ netsec_write(priv, NETSEC_REG_ADDR_DIS_CORE, 0);
+
+ usleep_range(1000, 2000);
+
+ if (!(netsec_read(priv, NETSEC_REG_TOP_STATUS) &
+ NETSEC_TOP_IRQ_REG_CODE_LOAD_END)) {
+ netif_err(priv, probe, priv->ndev,
+ "microengine start failed\n");
+ return -ENXIO;
+ }
+ netsec_write(priv, NETSEC_REG_TOP_STATUS,
+ NETSEC_TOP_IRQ_REG_CODE_LOAD_END);
+
+ value = NETSEC_PKT_CTRL_REG_MODE_NRM;
+ if (priv->ndev->mtu > ETH_DATA_LEN)
+ value |= NETSEC_PKT_CTRL_REG_EN_JUMBO;
+
+ /* change to normal mode */
+ netsec_write(priv, NETSEC_REG_DMA_MH_CTRL, MH_CTRL__MODE_TRANS);
+ netsec_write(priv, NETSEC_REG_PKT_CTRL, value);
+
+ while ((netsec_read(priv, NETSEC_REG_MODE_TRANS_COMP_STATUS) &
+ NETSEC_MODE_TRANS_COMP_IRQ_T2N) == 0)
+ cpu_relax();
+
+ /* clear any pending EMPTY/ERR irq status */
+ netsec_write(priv, NETSEC_REG_NRM_TX_STATUS, ~0);
+
+ /* Disable TX & RX intr */
+ netsec_write(priv, NETSEC_REG_INTEN_CLR, ~0);
+
+ return 0;
+}
+
+static int netsec_start_gmac(struct netsec_priv *priv)
+{
+ struct phy_device *phydev = priv->ndev->phydev;
+ u32 value = 0;
+ int ret;
+
+ if (phydev->speed != SPEED_1000)
+ value = (NETSEC_GMAC_MCR_REG_CST |
+ NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON);
+
+ if (netsec_mac_write(priv, GMAC_REG_MCR, value))
+ return -ETIMEDOUT;
+ if (netsec_mac_write(priv, GMAC_REG_BMR,
+ NETSEC_GMAC_BMR_REG_RESET))
+ return -ETIMEDOUT;
+
+ /* Wait soft reset */
+ usleep_range(1000, 5000);
+
+ ret = netsec_mac_read(priv, GMAC_REG_BMR, &value);
+ if (ret)
+ return ret;
+ if (value & NETSEC_GMAC_BMR_REG_SWR)
+ return -EAGAIN;
+
+ netsec_write(priv, MAC_REG_DESC_SOFT_RST, 1);
+ if (netsec_wait_while_busy(priv, MAC_REG_DESC_SOFT_RST, 1))
+ return -ETIMEDOUT;
+
+ netsec_write(priv, MAC_REG_DESC_INIT, 1);
+ if (netsec_wait_while_busy(priv, MAC_REG_DESC_INIT, 1))
+ return -ETIMEDOUT;
+
+ if (netsec_mac_write(priv, GMAC_REG_BMR,
+ NETSEC_GMAC_BMR_REG_COMMON))
+ return -ETIMEDOUT;
+ if (netsec_mac_write(priv, GMAC_REG_RDLAR,
+ NETSEC_GMAC_RDLAR_REG_COMMON))
+ return -ETIMEDOUT;
+ if (netsec_mac_write(priv, GMAC_REG_TDLAR,
+ NETSEC_GMAC_TDLAR_REG_COMMON))
+ return -ETIMEDOUT;
+ if (netsec_mac_write(priv, GMAC_REG_MFFR, 0x80000001))
+ return -ETIMEDOUT;
+
+ ret = netsec_mac_update_to_phy_state(priv);
+ if (ret)
+ return ret;
+
+ ret = netsec_mac_read(priv, GMAC_REG_OMR, &value);
+ if (ret)
+ return ret;
+
+ value |= NETSEC_GMAC_OMR_REG_SR;
+ value |= NETSEC_GMAC_OMR_REG_ST;
+
+ netsec_write(priv, NETSEC_REG_NRM_RX_INTEN_CLR, ~0);
+ netsec_write(priv, NETSEC_REG_NRM_TX_INTEN_CLR, ~0);
+
+ netsec_et_set_coalesce(priv->ndev, &priv->et_coalesce);
+
+ if (netsec_mac_write(priv, GMAC_REG_OMR, value))
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+static int netsec_stop_gmac(struct netsec_priv *priv)
+{
+ u32 value;
+ int ret;
+
+ ret = netsec_mac_read(priv, GMAC_REG_OMR, &value);
+ if (ret)
+ return ret;
+ value &= ~NETSEC_GMAC_OMR_REG_SR;
+ value &= ~NETSEC_GMAC_OMR_REG_ST;
+
+ /* disable all interrupts */
+ netsec_write(priv, NETSEC_REG_NRM_RX_INTEN_CLR, ~0);
+ netsec_write(priv, NETSEC_REG_NRM_TX_INTEN_CLR, ~0);
+
+ return netsec_mac_write(priv, GMAC_REG_OMR, value);
+}
+
+static void netsec_phy_adjust_link(struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+
+ if (ndev->phydev->link)
+ netsec_start_gmac(priv);
+ else
+ netsec_stop_gmac(priv);
+
+ phy_print_status(ndev->phydev);
+}
+
+static irqreturn_t netsec_irq_handler(int irq, void *dev_id)
+{
+ struct netsec_priv *priv = dev_id;
+ u32 val, status = netsec_read(priv, NETSEC_REG_TOP_STATUS);
+ unsigned long flags;
+
+ /* Disable interrupts */
+ if (status & NETSEC_IRQ_TX) {
+ val = netsec_read(priv, NETSEC_REG_NRM_TX_STATUS);
+ netsec_write(priv, NETSEC_REG_NRM_TX_STATUS, val);
+ }
+ if (status & NETSEC_IRQ_RX) {
+ val = netsec_read(priv, NETSEC_REG_NRM_RX_STATUS);
+ netsec_write(priv, NETSEC_REG_NRM_RX_STATUS, val);
+ }
+
+ spin_lock_irqsave(&priv->reglock, flags);
+ netsec_write(priv, NETSEC_REG_INTEN_CLR, NETSEC_IRQ_RX | NETSEC_IRQ_TX);
+ spin_unlock_irqrestore(&priv->reglock, flags);
+
+ napi_schedule(&priv->napi);
+
+ return IRQ_HANDLED;
+}
+
+static int netsec_netdev_open(struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+ int ret;
+
+ pm_runtime_get_sync(priv->dev);
+
+ ret = netsec_setup_rx_dring(priv);
+ if (ret) {
+ netif_err(priv, probe, priv->ndev,
+ "%s: fail setup ring\n", __func__);
+ goto err1;
+ }
+
+ ret = request_irq(priv->ndev->irq, netsec_irq_handler,
+ IRQF_SHARED, "netsec", priv);
+ if (ret) {
+ netif_err(priv, drv, priv->ndev, "request_irq failed\n");
+ goto err2;
+ }
+
+ if (dev_of_node(priv->dev)) {
+ if (!of_phy_connect(priv->ndev, priv->phy_np,
+ netsec_phy_adjust_link, 0,
+ priv->phy_interface)) {
+ netif_err(priv, link, priv->ndev, "missing PHY\n");
+ goto err3;
+ }
+ } else {
+ ret = phy_connect_direct(priv->ndev, priv->phydev,
+ netsec_phy_adjust_link,
+ priv->phy_interface);
+ if (ret) {
+ netif_err(priv, link, priv->ndev,
+ "phy_connect_direct() failed (%d)\n", ret);
+ goto err3;
+ }
+ }
+
+ phy_start(ndev->phydev);
+
+ netsec_start_gmac(priv);
+ napi_enable(&priv->napi);
+ netif_start_queue(ndev);
+
+ /* Enable RX intr. */
+ netsec_write(priv, NETSEC_REG_INTEN_SET, NETSEC_IRQ_RX);
+
+ return 0;
+err3:
+ free_irq(priv->ndev->irq, priv);
+err2:
+ netsec_uninit_pkt_dring(priv, NETSEC_RING_RX);
+err1:
+ pm_runtime_put_sync(priv->dev);
+ return ret;
+}
+
+static int netsec_netdev_stop(struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+
+ netif_stop_queue(priv->ndev);
+ dma_wmb();
+
+ napi_disable(&priv->napi);
+
+ netsec_write(priv, NETSEC_REG_INTEN_CLR, ~0);
+ netsec_stop_gmac(priv);
+
+ free_irq(priv->ndev->irq, priv);
+
+ netsec_uninit_pkt_dring(priv, NETSEC_RING_TX);
+ netsec_uninit_pkt_dring(priv, NETSEC_RING_RX);
+
+ phy_stop(ndev->phydev);
+ phy_disconnect(ndev->phydev);
+
+ pm_runtime_put_sync(priv->dev);
+
+ return 0;
+}
+
+static int netsec_netdev_init(struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+ int ret;
+
+ ret = netsec_alloc_dring(priv, NETSEC_RING_TX);
+ if (ret)
+ return ret;
+
+ ret = netsec_alloc_dring(priv, NETSEC_RING_RX);
+ if (ret)
+ goto err1;
+
+ ret = netsec_reset_hardware(priv);
+ if (ret)
+ goto err2;
+
+ return 0;
+err2:
+ netsec_free_dring(priv, NETSEC_RING_RX);
+err1:
+ netsec_free_dring(priv, NETSEC_RING_TX);
+ return ret;
+}
+
+static void netsec_netdev_uninit(struct net_device *ndev)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+
+ netsec_free_dring(priv, NETSEC_RING_RX);
+ netsec_free_dring(priv, NETSEC_RING_TX);
+}
+
+static int netsec_netdev_set_features(struct net_device *ndev,
+ netdev_features_t features)
+{
+ struct netsec_priv *priv = netdev_priv(ndev);
+
+ priv->rx_cksum_offload_flag = !!(features & NETIF_F_RXCSUM);
+
+ return 0;
+}
+
+static int netsec_netdev_ioctl(struct net_device *ndev, struct ifreq *ifr,
+ int cmd)
+{
+ return phy_mii_ioctl(ndev->phydev, ifr, cmd);
+}
+
+static const struct net_device_ops netsec_netdev_ops = {
+ .ndo_init = netsec_netdev_init,
+ .ndo_uninit = netsec_netdev_uninit,
+ .ndo_open = netsec_netdev_open,
+ .ndo_stop = netsec_netdev_stop,
+ .ndo_start_xmit = netsec_netdev_start_xmit,
+ .ndo_set_features = netsec_netdev_set_features,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = netsec_netdev_ioctl,
+};
+
+/*************************************************************/
+/*************************************************************/
+
+static int netsec_of_probe(struct platform_device *pdev,
+ struct netsec_priv *priv)
+{
+ int clk_count, ret, i;
+
+ priv->phy_np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
+ if (!priv->phy_np) {
+ dev_err(&pdev->dev, "missing required property 'phy-handle'\n");
+ return -EINVAL;
+ }
+
+ /* we require named clocks if there is more than one */
+ clk_count = of_property_count_strings(pdev->dev.of_node, "clock-names");
+ if (clk_count > 1) {
+ if (clk_count > ARRAY_SIZE(priv->clk)) {
+ dev_err(&pdev->dev, "too many clocks specified (%d)\n",
+ clk_count);
+ return -EINVAL;
+ }
+
+ for (i = 0; i < clk_count; i++) {
+ const char *clk_name;
+
+ ret = of_property_read_string_index(pdev->dev.of_node,
+ "clock-names", i,
+ &clk_name);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "failed to parse 'clock-names'\n");
+ return ret;
+ }
+ priv->clk[i] = devm_clk_get(&pdev->dev, clk_name);
+ if (!strcmp(clk_name, "phy_refclk")) {
+ priv->freq = clk_get_rate(priv->clk[i]);
+ dev_dbg(&pdev->dev,
+ "found PHY refclock #%d freq %u\n",
+ i, priv->freq);
+ }
+ }
+ priv->clock_count = clk_count;
+ } else {
+ priv->clk[0] = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ dev_err(&pdev->dev,
+ "missing required property 'clocks'\n");
+ return PTR_ERR(priv->clk);
+ }
+ priv->freq = clk_get_rate(priv->clk[0]);
+ priv->clock_count = 1;
+ }
+ return 0;
+}
+
+static int netsec_acpi_probe(struct platform_device *pdev,
+ struct netsec_priv *priv, u32 *phy_addr)
+{
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_ACPI))
+ return -ENODEV;
+
+ ret = device_property_read_u32(&pdev->dev, "phy-channel", phy_addr);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "missing required property 'phy-channel'\n");
+ return ret;
+ }
+
+ ret = device_property_read_u32(&pdev->dev,
+ "socionext,phy-clock-frequency",
+ &priv->freq);
+ if (ret)
+ dev_err(&pdev->dev,
+ "missing required property 'socionext,phy-clock-frequency'\n");
+ return ret;
+}
+
+static void netsec_unregister_mdio(struct netsec_priv *priv)
+{
+ struct phy_device *phydev = priv->phydev;
+
+ if (!dev_of_node(priv->dev) && phydev) {
+ phy_device_remove(phydev);
+ phy_device_free(phydev);
+ }
+
+ mdiobus_unregister(priv->mii_bus);
+}
+
+static int netsec_register_mdio(struct netsec_priv *priv, u32 phy_addr)
+{
+ struct mii_bus *bus;
+ int ret;
+
+ bus = devm_mdiobus_alloc(priv->dev);
+ if (!bus)
+ return -ENOMEM;
+
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%s", dev_name(priv->dev));
+ bus->priv = priv;
+ bus->name = "SNI NETSEC MDIO";
+ bus->read = netsec_phy_read;
+ bus->write = netsec_phy_write;
+ bus->parent = priv->dev;
+ priv->mii_bus = bus;
+
+ if (dev_of_node(priv->dev)) {
+ ret = of_mdiobus_register(bus, dev_of_node(priv->dev));
+ if (ret) {
+ dev_err(priv->dev, "mdiobus register err(%d)\n", ret);
+ return ret;
+ }
+ } else {
+ /* Mask out all PHYs from auto probing. */
+ bus->phy_mask = ~0;
+ ret = mdiobus_register(bus);
+ if (ret) {
+ dev_err(priv->dev, "mdiobus register err(%d)\n", ret);
+ return ret;
+ }
+
+ priv->phydev = get_phy_device(priv->mii_bus, phy_addr, false);
+ if (IS_ERR(priv->phydev)) {
+ ret = PTR_ERR(priv->phydev);
+ dev_err(priv->dev, "get_phy_device err(%d)\n", ret);
+ priv->phydev = NULL;
+ return -ENODEV;
+ }
+
+ ret = phy_device_register(priv->phydev);
+ if (ret)
+ dev_err(priv->dev,
+ "phy_device_register err(%d)\n", ret);
+ }
+
+ return ret;
+}
+
+static int netsec_probe(struct platform_device *pdev)
+{
+ struct resource *mmio_res, *eeprom_res, *irq_res;
+ u8 *mac, macbuf[ETH_ALEN];
+ struct netsec_priv *priv;
+ struct net_device *ndev;
+ u32 hw_ver, phy_addr = 0;
+ int ret;
+
+ mmio_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mmio_res) {
+ dev_err(&pdev->dev, "No MMIO resource found.\n");
+ return -ENODEV;
+ }
+
+ eeprom_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!eeprom_res) {
+ dev_info(&pdev->dev, "No EEPROM resource found.\n");
+ return -ENODEV;
+ }
+
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!irq_res) {
+ dev_err(&pdev->dev, "No IRQ resource found.\n");
+ return -ENODEV;
+ }
+
+ ndev = alloc_etherdev(sizeof(*priv));
+ if (!ndev)
+ return -ENOMEM;
+
+ priv = netdev_priv(ndev);
+
+ spin_lock_init(&priv->reglock);
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+ platform_set_drvdata(pdev, priv);
+ ndev->irq = irq_res->start;
+ priv->dev = &pdev->dev;
+ priv->ndev = ndev;
+
+ priv->msg_enable = NETIF_MSG_TX_ERR | NETIF_MSG_HW | NETIF_MSG_DRV |
+ NETIF_MSG_LINK | NETIF_MSG_PROBE;
+
+ priv->phy_interface = device_get_phy_mode(&pdev->dev);
+ if (priv->phy_interface < 0) {
+ dev_err(&pdev->dev, "missing required property 'phy-mode'\n");
+ ret = -ENODEV;
+ goto free_ndev;
+ }
+
+ priv->ioaddr = devm_ioremap(&pdev->dev, mmio_res->start,
+ resource_size(mmio_res));
+ if (!priv->ioaddr) {
+ dev_err(&pdev->dev, "devm_ioremap() failed\n");
+ ret = -ENXIO;
+ goto free_ndev;
+ }
+
+ priv->eeprom_base = devm_ioremap(&pdev->dev, eeprom_res->start,
+ resource_size(eeprom_res));
+ if (!priv->eeprom_base) {
+ dev_err(&pdev->dev, "devm_ioremap() failed for EEPROM\n");
+ ret = -ENXIO;
+ goto free_ndev;
+ }
+
+ mac = device_get_mac_address(&pdev->dev, macbuf, sizeof(macbuf));
+ if (mac)
+ ether_addr_copy(ndev->dev_addr, mac);
+
+ if (priv->eeprom_base &&
+ (!mac || !is_valid_ether_addr(ndev->dev_addr))) {
+ const u8 *macp = priv->eeprom_base + NETSEC_EEPROM_MAC_ADDRESS;
+
+ ndev->dev_addr[0] = macp[3];
+ ndev->dev_addr[1] = macp[2];
+ ndev->dev_addr[2] = macp[1];
+ ndev->dev_addr[3] = macp[0];
+ ndev->dev_addr[4] = macp[7];
+ ndev->dev_addr[5] = macp[6];
+ }
+
+ if (!is_valid_ether_addr(ndev->dev_addr)) {
+ dev_warn(&pdev->dev, "No MAC address found, using random\n");
+ eth_hw_addr_random(ndev);
+ }
+
+ if (dev_of_node(&pdev->dev))
+ ret = netsec_of_probe(pdev, priv);
+ else
+ ret = netsec_acpi_probe(pdev, priv, &phy_addr);
+ if (ret)
+ goto free_ndev;
+
+ if (!priv->freq) {
+ dev_err(&pdev->dev, "missing PHY reference clock frequency\n");
+ ret = -ENODEV;
+ goto free_ndev;
+ }
+
+ /* default for throughput */
+ priv->et_coalesce.rx_coalesce_usecs = 500;
+ priv->et_coalesce.rx_max_coalesced_frames = 8;
+ priv->et_coalesce.tx_coalesce_usecs = 500;
+ priv->et_coalesce.tx_max_coalesced_frames = 8;
+
+ ret = device_property_read_u32(&pdev->dev, "max-frame-size",
+ &ndev->max_mtu);
+ if (ret < 0)
+ ndev->max_mtu = ETH_DATA_LEN;
+
+ /* runtime_pm coverage just for probe, open/close also cover it */
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
+
+ hw_ver = netsec_read(priv, NETSEC_REG_F_TAIKI_VER);
+ /* this driver only supports F_TAIKI style NETSEC */
+ if (NETSEC_F_NETSEC_VER_MAJOR_NUM(hw_ver) !=
+ NETSEC_F_NETSEC_VER_MAJOR_NUM(NETSEC_REG_NETSEC_VER_F_TAIKI)) {
+ ret = -ENODEV;
+ goto pm_disable;
+ }
+
+ dev_info(&pdev->dev, "hardware revision %d.%d\n",
+ hw_ver >> 16, hw_ver & 0xffff);
+
+ netif_napi_add(ndev, &priv->napi, netsec_napi_poll, NAPI_BUDGET);
+
+ ndev->netdev_ops = &netsec_netdev_ops;
+ ndev->ethtool_ops = &netsec_ethtool_ops;
+
+ ndev->features |= NETIF_F_HIGHDMA | NETIF_F_RXCSUM | NETIF_F_GSO |
+ NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+ ndev->hw_features = ndev->features;
+
+ priv->rx_cksum_offload_flag = true;
+
+ ret = netsec_register_mdio(priv, phy_addr);
+ if (ret)
+ goto unreg_napi;
+
+ if (dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)))
+ dev_warn(&pdev->dev, "Failed to enable 64-bit DMA\n");
+
+ ret = register_netdev(ndev);
+ if (ret) {
+ netif_err(priv, probe, ndev, "register_netdev() failed\n");
+ goto unreg_mii;
+ }
+
+ pm_runtime_put_sync(&pdev->dev);
+ return 0;
+
+unreg_mii:
+ netsec_unregister_mdio(priv);
+unreg_napi:
+ netif_napi_del(&priv->napi);
+pm_disable:
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+free_ndev:
+ free_netdev(ndev);
+ dev_err(&pdev->dev, "init failed\n");
+
+ return ret;
+}
+
+static int netsec_remove(struct platform_device *pdev)
+{
+ struct netsec_priv *priv = platform_get_drvdata(pdev);
+
+ unregister_netdev(priv->ndev);
+
+ netsec_unregister_mdio(priv);
+
+ netif_napi_del(&priv->napi);
+
+ pm_runtime_disable(&pdev->dev);
+ free_netdev(priv->ndev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int netsec_runtime_suspend(struct device *dev)
+{
+ struct netsec_priv *priv = dev_get_drvdata(dev);
+ int n;
+
+ netsec_write(priv, NETSEC_REG_CLK_EN, 0);
+
+ for (n = priv->clock_count - 1; n >= 0; n--)
+ clk_disable_unprepare(priv->clk[n]);
+
+ return 0;
+}
+
+static int netsec_runtime_resume(struct device *dev)
+{
+ struct netsec_priv *priv = dev_get_drvdata(dev);
+ int n;
+
+ /* first let the clocks back on */
+ for (n = 0; n < priv->clock_count; n++)
+ clk_prepare_enable(priv->clk[n]);
+
+ netsec_write(priv, NETSEC_REG_CLK_EN, NETSEC_CLK_EN_REG_DOM_D |
+ NETSEC_CLK_EN_REG_DOM_C |
+ NETSEC_CLK_EN_REG_DOM_G);
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops netsec_pm_ops = {
+ SET_RUNTIME_PM_OPS(netsec_runtime_suspend, netsec_runtime_resume, NULL)
+};
+
+static const struct of_device_id netsec_dt_ids[] = {
+ { .compatible = "socionext,synquacer-netsec" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, netsec_dt_ids);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id netsec_acpi_ids[] = {
+ { "SCX0001" },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, netsec_acpi_ids);
+#endif
+
+static struct platform_driver netsec_driver = {
+ .probe = netsec_probe,
+ .remove = netsec_remove,
+ .driver = {
+ .name = "netsec",
+ .pm = &netsec_pm_ops,
+ .of_match_table = netsec_dt_ids,
+ .acpi_match_table = ACPI_PTR(netsec_acpi_ids),
+ },
+};
+module_platform_driver(netsec_driver);
+
+MODULE_AUTHOR("Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_AUTHOR("Ard Biesheuvel <ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_DESCRIPTION("NETSEC Ethernet driver");
+MODULE_LICENSE("GPL");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCHv2 3/3] MAINTAINERS: Add entry for Socionext ethernet driver
From: jassisinghbrar-Re5JQEeQqe8AvxtiuMwx3w @ 2017-12-12 17:16 UTC (permalink / raw)
To: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: davem-fT/PcQaiUtIeIZ0/mPfg9Q,
arnd.bergmann-QSEj5FYQhm4dnm+yROfE0A,
ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
Jassi Brar
In-Reply-To: <1513098873-20977-1-git-send-email-jassisinghbrar-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
From: Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Add entry for the Socionext Netsec controller driver and DT bindings.
Acked-by: Ard Biesheuvel <ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
MAINTAINERS | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 9e0045e..0e1f0d4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12630,6 +12630,13 @@ F: drivers/md/raid*
F: include/linux/raid/
F: include/uapi/linux/raid/
+SOCIONEXT (SNI) NETSEC NETWORK DRIVER
+M: Jassi Brar <jaswinder.singh-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+L: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
+S: Maintained
+F: drivers/net/ethernet/socionext/netsec.c
+F: Documentation/devicetree/bindings/net/socionext-netsec.txt
+
SONIC NETWORK DRIVER
M: Thomas Bogendoerfer <tsbogend-I1c7kopa9pxLokYuJOExCg@public.gmane.org>
L: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox