* [PATCH AUTOSEL 4.14 105/105] net: mvmdio: defer probe of orion-mdio if a clock is not ready
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Josua Mayer, Andrew Lunn, David S . Miller, Sasha Levin, netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Josua Mayer <josua@solid-run.com>
[ Upstream commit 433a06d7d74e677c40b1148c70c48677ff62fb6b ]
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/ethernet/marvell/mvmdio.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvmdio.c b/drivers/net/ethernet/marvell/mvmdio.c
index 0495487f7b42..c8e3c1119313 100644
--- a/drivers/net/ethernet/marvell/mvmdio.c
+++ b/drivers/net/ethernet/marvell/mvmdio.c
@@ -321,6 +321,10 @@ static int orion_mdio_probe(struct platform_device *pdev)
for (i = 0; i < ARRAY_SIZE(dev->clk); i++) {
dev->clk[i] = of_clk_get(pdev->dev.of_node, i);
+ if (PTR_ERR(dev->clk[i]) == -EPROBE_DEFER) {
+ ret = -EPROBE_DEFER;
+ goto out_clk;
+ }
if (IS_ERR(dev->clk[i]))
break;
clk_prepare_enable(dev->clk[i]);
@@ -365,6 +369,7 @@ static int orion_mdio_probe(struct platform_device *pdev)
if (dev->err_interrupt > 0)
writel(0, dev->regs + MVMDIO_ERR_INT_MASK);
+out_clk:
for (i = 0; i < ARRAY_SIZE(dev->clk); i++) {
if (IS_ERR(dev->clk[i]))
break;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 102/105] gtp: fix Illegal context switch in RCU read-side critical section.
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Taehee Yoo, David S . Miller, Sasha Levin, osmocom-net-gprs,
netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Taehee Yoo <ap420073@gmail.com>
[ Upstream commit 3f167e1921865b379a9becf03828e7202c7b4917 ]
ipv4_pdp_add() is called in RCU read-side critical section.
So GFP_KERNEL should not be used in the function.
This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL.
Test commands:
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 100 200 1.1.1.1 2.2.2.2
Splat looks like:
[ 130.618881] =============================
[ 130.626382] WARNING: suspicious RCU usage
[ 130.626994] 5.2.0-rc6+ #50 Not tainted
[ 130.627622] -----------------------------
[ 130.628223] ./include/linux/rcupdate.h:266 Illegal context switch in RCU read-side critical section!
[ 130.629684]
[ 130.629684] other info that might help us debug this:
[ 130.629684]
[ 130.631022]
[ 130.631022] rcu_scheduler_active = 2, debug_locks = 1
[ 130.632136] 4 locks held by gtp-tunnel/1025:
[ 130.632925] #0: 000000002b93c8b7 (cb_lock){++++}, at: genl_rcv+0x15/0x40
[ 130.634159] #1: 00000000f17bc999 (genl_mutex){+.+.}, at: genl_rcv_msg+0xfb/0x130
[ 130.635487] #2: 00000000c644ed8e (rtnl_mutex){+.+.}, at: gtp_genl_new_pdp+0x18c/0x1150 [gtp]
[ 130.636936] #3: 0000000007a1cde7 (rcu_read_lock){....}, at: gtp_genl_new_pdp+0x187/0x1150 [gtp]
[ 130.638348]
[ 130.638348] stack backtrace:
[ 130.639062] CPU: 1 PID: 1025 Comm: gtp-tunnel Not tainted 5.2.0-rc6+ #50
[ 130.641318] Call Trace:
[ 130.641707] dump_stack+0x7c/0xbb
[ 130.642252] ___might_sleep+0x2c0/0x3b0
[ 130.642862] kmem_cache_alloc_trace+0x1cd/0x2b0
[ 130.643591] gtp_genl_new_pdp+0x6c5/0x1150 [gtp]
[ 130.644371] genl_family_rcv_msg+0x63a/0x1030
[ 130.645074] ? mutex_lock_io_nested+0x1090/0x1090
[ 130.645845] ? genl_unregister_family+0x630/0x630
[ 130.646592] ? debug_show_all_locks+0x2d0/0x2d0
[ 130.647293] ? check_flags.part.40+0x440/0x440
[ 130.648099] genl_rcv_msg+0xa3/0x130
[ ... ]
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/gtp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index 2756edd84abc..c751f87c935e 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -956,7 +956,7 @@ static int ipv4_pdp_add(struct gtp_dev *gtp, struct sock *sk,
}
- pctx = kmalloc(sizeof(struct pdp_ctx), GFP_KERNEL);
+ pctx = kmalloc(sizeof(*pctx), GFP_ATOMIC);
if (pctx == NULL)
return -ENOMEM;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 099/105] gtp: add missing gtp_encap_disable_sock() in gtp_encap_enable()
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Taehee Yoo, David S . Miller, Sasha Levin, osmocom-net-gprs,
netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Taehee Yoo <ap420073@gmail.com>
[ Upstream commit e30155fd23c9c141cbe7d99b786e10a83a328837 ]
If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.
Fixes: 91ed81f9abc7 ("gtp: support SGSN-side tunnels")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/gtp.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index f38e32a7ec9c..dba3869b61be 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -845,8 +845,13 @@ static int gtp_encap_enable(struct gtp_dev *gtp, struct nlattr *data[])
if (data[IFLA_GTP_ROLE]) {
role = nla_get_u32(data[IFLA_GTP_ROLE]);
- if (role > GTP_ROLE_SGSN)
+ if (role > GTP_ROLE_SGSN) {
+ if (sk0)
+ gtp_encap_disable_sock(sk0);
+ if (sk1u)
+ gtp_encap_disable_sock(sk1u);
return -EINVAL;
+ }
}
gtp->sk0 = sk0;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 100/105] Bluetooth: validate BLE connection interval updates
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: csonsino, Marcel Holtmann, Sasha Levin, linux-bluetooth, netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: csonsino <csonsino@gmail.com>
[ Upstream commit c49a8682fc5d298d44e8d911f4fa14690ea9485e ]
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/bluetooth/hci_event.c | 5 +++++
net/bluetooth/l2cap_core.c | 9 ++++++++-
2 files changed, 13 insertions(+), 1 deletion(-)
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 363dc85bbc5c..3d2f64a6d623 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -5089,6 +5089,11 @@ static void hci_le_remote_conn_param_req_evt(struct hci_dev *hdev,
return send_conn_param_neg_reply(hdev, handle,
HCI_ERROR_UNKNOWN_CONN_ID);
+ if (min < hcon->le_conn_min_interval ||
+ max > hcon->le_conn_max_interval)
+ return send_conn_param_neg_reply(hdev, handle,
+ HCI_ERROR_INVALID_LL_PARAMS);
+
if (hci_check_conn_params(min, max, latency, timeout))
return send_conn_param_neg_reply(hdev, handle,
HCI_ERROR_INVALID_LL_PARAMS);
diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index 0c2219f483d7..4dc1db85a9c2 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -5287,7 +5287,14 @@ static inline int l2cap_conn_param_update_req(struct l2cap_conn *conn,
memset(&rsp, 0, sizeof(rsp));
- err = hci_check_conn_params(min, max, latency, to_multiplier);
+ if (min < hcon->le_conn_min_interval ||
+ max > hcon->le_conn_max_interval) {
+ BT_DBG("requested connection interval exceeds current bounds.");
+ err = -EINVAL;
+ } else {
+ err = hci_check_conn_params(min, max, latency, to_multiplier);
+ }
+
if (err)
rsp.result = cpu_to_le16(L2CAP_CONN_PARAM_REJECTED);
else
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 076/105] ath10k: add missing error handling
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Claire Chang, Brian Norris, Kalle Valo, Sasha Levin, ath10k,
linux-wireless, netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Claire Chang <tientzu@chromium.org>
[ Upstream commit 4b553f3ca4cbde67399aa3a756c37eb92145b8a1 ]
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d2025 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/ath/ath10k/sdio.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index da9dbf3ddaa5..c6440d28ab48 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -610,6 +610,10 @@ static int ath10k_sdio_mbox_rx_alloc(struct ath10k *ar,
full_len,
last_in_bundle,
last_in_bundle);
+ if (ret) {
+ ath10k_warn(ar, "alloc_rx_pkt error %d\n", ret);
+ goto err;
+ }
}
ar_sdio->n_rx_pkts = i;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 075/105] ipvs: fix tinfo memory leak in start_sync_thread
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Julian Anastasov, syzbot+7e2e50c8adfccd2e5041, Eric Biggers,
Simon Horman, Pablo Neira Ayuso, Sasha Levin, netdev, lvs-devel,
netfilter-devel, coreteam
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Julian Anastasov <ja@ssi.bg>
[ Upstream commit 5db7c8b9f9fc2aeec671ae3ca6375752c162e0e7 ]
syzkaller reports for memory leak in start_sync_thread [1]
As Eric points out, kthread may start and stop before the
threadfn function is called, so there is no chance the
data (tinfo in our case) to be released in thread.
Fix this by releasing tinfo in the controlling code instead.
[1]
BUG: memory leak
unreferenced object 0xffff8881206bf700 (size 32):
comm "syz-executor761", pid 7268, jiffies 4294943441 (age 20.470s)
hex dump (first 32 bytes):
00 40 7c 09 81 88 ff ff 80 45 b8 21 81 88 ff ff .@|......E.!....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000057619e23>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
[<0000000057619e23>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<0000000057619e23>] slab_alloc mm/slab.c:3326 [inline]
[<0000000057619e23>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
[<0000000086ce5479>] kmalloc include/linux/slab.h:547 [inline]
[<0000000086ce5479>] start_sync_thread+0x5d2/0xe10 net/netfilter/ipvs/ip_vs_sync.c:1862
[<000000001a9229cc>] do_ip_vs_set_ctl+0x4c5/0x780 net/netfilter/ipvs/ip_vs_ctl.c:2402
[<00000000ece457c8>] nf_sockopt net/netfilter/nf_sockopt.c:106 [inline]
[<00000000ece457c8>] nf_setsockopt+0x4c/0x80 net/netfilter/nf_sockopt.c:115
[<00000000942f62d4>] ip_setsockopt net/ipv4/ip_sockglue.c:1258 [inline]
[<00000000942f62d4>] ip_setsockopt+0x9b/0xb0 net/ipv4/ip_sockglue.c:1238
[<00000000a56a8ffd>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616
[<00000000fa895401>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130
[<0000000095eef4cf>] __sys_setsockopt+0x98/0x120 net/socket.c:2078
[<000000009747cf88>] __do_sys_setsockopt net/socket.c:2089 [inline]
[<000000009747cf88>] __se_sys_setsockopt net/socket.c:2086 [inline]
[<000000009747cf88>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086
[<00000000ded8ba80>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
[<00000000893b4ac8>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: syzbot+7e2e50c8adfccd2e5041@syzkaller.appspotmail.com
Suggested-by: Eric Biggers <ebiggers@kernel.org>
Fixes: 998e7a76804b ("ipvs: Use kthread_run() instead of doing a double-fork via kernel_thread()")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
include/net/ip_vs.h | 6 +-
net/netfilter/ipvs/ip_vs_ctl.c | 4 -
net/netfilter/ipvs/ip_vs_sync.c | 134 +++++++++++++++++---------------
3 files changed, 76 insertions(+), 68 deletions(-)
diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h
index 5d08c1950e7d..82bc9f0e8a76 100644
--- a/include/net/ip_vs.h
+++ b/include/net/ip_vs.h
@@ -812,11 +812,12 @@ struct ipvs_master_sync_state {
struct ip_vs_sync_buff *sync_buff;
unsigned long sync_queue_len;
unsigned int sync_queue_delay;
- struct task_struct *master_thread;
struct delayed_work master_wakeup_work;
struct netns_ipvs *ipvs;
};
+struct ip_vs_sync_thread_data;
+
/* How much time to keep dests in trash */
#define IP_VS_DEST_TRASH_PERIOD (120 * HZ)
@@ -947,7 +948,8 @@ struct netns_ipvs {
spinlock_t sync_lock;
struct ipvs_master_sync_state *ms;
spinlock_t sync_buff_lock;
- struct task_struct **backup_threads;
+ struct ip_vs_sync_thread_data *master_tinfo;
+ struct ip_vs_sync_thread_data *backup_tinfo;
int threads_mask;
volatile int sync_state;
struct mutex sync_mutex;
diff --git a/net/netfilter/ipvs/ip_vs_ctl.c b/net/netfilter/ipvs/ip_vs_ctl.c
index 6d7608b88f66..4648dccebf59 100644
--- a/net/netfilter/ipvs/ip_vs_ctl.c
+++ b/net/netfilter/ipvs/ip_vs_ctl.c
@@ -2414,9 +2414,7 @@ do_ip_vs_set_ctl(struct sock *sk, int cmd, void __user *user, unsigned int len)
cfg.syncid = dm->syncid;
ret = start_sync_thread(ipvs, &cfg, dm->state);
} else {
- mutex_lock(&ipvs->sync_mutex);
ret = stop_sync_thread(ipvs, dm->state);
- mutex_unlock(&ipvs->sync_mutex);
}
goto out_dec;
}
@@ -3524,10 +3522,8 @@ static int ip_vs_genl_del_daemon(struct netns_ipvs *ipvs, struct nlattr **attrs)
if (!attrs[IPVS_DAEMON_ATTR_STATE])
return -EINVAL;
- mutex_lock(&ipvs->sync_mutex);
ret = stop_sync_thread(ipvs,
nla_get_u32(attrs[IPVS_DAEMON_ATTR_STATE]));
- mutex_unlock(&ipvs->sync_mutex);
return ret;
}
diff --git a/net/netfilter/ipvs/ip_vs_sync.c b/net/netfilter/ipvs/ip_vs_sync.c
index 5e07f7a6794e..b578ebb3d7ef 100644
--- a/net/netfilter/ipvs/ip_vs_sync.c
+++ b/net/netfilter/ipvs/ip_vs_sync.c
@@ -195,6 +195,7 @@ union ip_vs_sync_conn {
#define IPVS_OPT_F_PARAM (1 << (IPVS_OPT_PARAM-1))
struct ip_vs_sync_thread_data {
+ struct task_struct *task;
struct netns_ipvs *ipvs;
struct socket *sock;
char *buf;
@@ -374,8 +375,11 @@ static inline void sb_queue_tail(struct netns_ipvs *ipvs,
max(IPVS_SYNC_SEND_DELAY, 1));
ms->sync_queue_len++;
list_add_tail(&sb->list, &ms->sync_queue);
- if ((++ms->sync_queue_delay) == IPVS_SYNC_WAKEUP_RATE)
- wake_up_process(ms->master_thread);
+ if ((++ms->sync_queue_delay) == IPVS_SYNC_WAKEUP_RATE) {
+ int id = (int)(ms - ipvs->ms);
+
+ wake_up_process(ipvs->master_tinfo[id].task);
+ }
} else
ip_vs_sync_buff_release(sb);
spin_unlock(&ipvs->sync_lock);
@@ -1645,8 +1649,10 @@ static void master_wakeup_work_handler(struct work_struct *work)
spin_lock_bh(&ipvs->sync_lock);
if (ms->sync_queue_len &&
ms->sync_queue_delay < IPVS_SYNC_WAKEUP_RATE) {
+ int id = (int)(ms - ipvs->ms);
+
ms->sync_queue_delay = IPVS_SYNC_WAKEUP_RATE;
- wake_up_process(ms->master_thread);
+ wake_up_process(ipvs->master_tinfo[id].task);
}
spin_unlock_bh(&ipvs->sync_lock);
}
@@ -1712,10 +1718,6 @@ static int sync_thread_master(void *data)
if (sb)
ip_vs_sync_buff_release(sb);
- /* release the sending multicast socket */
- sock_release(tinfo->sock);
- kfree(tinfo);
-
return 0;
}
@@ -1749,11 +1751,6 @@ static int sync_thread_backup(void *data)
}
}
- /* release the sending multicast socket */
- sock_release(tinfo->sock);
- kfree(tinfo->buf);
- kfree(tinfo);
-
return 0;
}
@@ -1761,8 +1758,8 @@ static int sync_thread_backup(void *data)
int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
int state)
{
- struct ip_vs_sync_thread_data *tinfo = NULL;
- struct task_struct **array = NULL, *task;
+ struct ip_vs_sync_thread_data *ti = NULL, *tinfo;
+ struct task_struct *task;
struct net_device *dev;
char *name;
int (*threadfn)(void *data);
@@ -1831,7 +1828,7 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
threadfn = sync_thread_master;
} else if (state == IP_VS_STATE_BACKUP) {
result = -EEXIST;
- if (ipvs->backup_threads)
+ if (ipvs->backup_tinfo)
goto out_early;
ipvs->bcfg = *c;
@@ -1858,28 +1855,22 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
master_wakeup_work_handler);
ms->ipvs = ipvs;
}
- } else {
- array = kcalloc(count, sizeof(struct task_struct *),
- GFP_KERNEL);
- result = -ENOMEM;
- if (!array)
- goto out;
}
+ result = -ENOMEM;
+ ti = kcalloc(count, sizeof(struct ip_vs_sync_thread_data),
+ GFP_KERNEL);
+ if (!ti)
+ goto out;
for (id = 0; id < count; id++) {
- result = -ENOMEM;
- tinfo = kmalloc(sizeof(*tinfo), GFP_KERNEL);
- if (!tinfo)
- goto out;
+ tinfo = &ti[id];
tinfo->ipvs = ipvs;
- tinfo->sock = NULL;
if (state == IP_VS_STATE_BACKUP) {
+ result = -ENOMEM;
tinfo->buf = kmalloc(ipvs->bcfg.sync_maxlen,
GFP_KERNEL);
if (!tinfo->buf)
goto out;
- } else {
- tinfo->buf = NULL;
}
tinfo->id = id;
if (state == IP_VS_STATE_MASTER)
@@ -1894,17 +1885,15 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
result = PTR_ERR(task);
goto out;
}
- tinfo = NULL;
- if (state == IP_VS_STATE_MASTER)
- ipvs->ms[id].master_thread = task;
- else
- array[id] = task;
+ tinfo->task = task;
}
/* mark as active */
- if (state == IP_VS_STATE_BACKUP)
- ipvs->backup_threads = array;
+ if (state == IP_VS_STATE_MASTER)
+ ipvs->master_tinfo = ti;
+ else
+ ipvs->backup_tinfo = ti;
spin_lock_bh(&ipvs->sync_buff_lock);
ipvs->sync_state |= state;
spin_unlock_bh(&ipvs->sync_buff_lock);
@@ -1919,29 +1908,31 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
out:
/* We do not need RTNL lock anymore, release it here so that
- * sock_release below and in the kthreads can use rtnl_lock
- * to leave the mcast group.
+ * sock_release below can use rtnl_lock to leave the mcast group.
*/
rtnl_unlock();
- count = id;
- while (count-- > 0) {
- if (state == IP_VS_STATE_MASTER)
- kthread_stop(ipvs->ms[count].master_thread);
- else
- kthread_stop(array[count]);
+ id = min(id, count - 1);
+ if (ti) {
+ for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+ if (tinfo->task)
+ kthread_stop(tinfo->task);
+ }
}
if (!(ipvs->sync_state & IP_VS_STATE_MASTER)) {
kfree(ipvs->ms);
ipvs->ms = NULL;
}
mutex_unlock(&ipvs->sync_mutex);
- if (tinfo) {
- if (tinfo->sock)
- sock_release(tinfo->sock);
- kfree(tinfo->buf);
- kfree(tinfo);
+
+ /* No more mutexes, release socks */
+ if (ti) {
+ for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+ if (tinfo->sock)
+ sock_release(tinfo->sock);
+ kfree(tinfo->buf);
+ }
+ kfree(ti);
}
- kfree(array);
return result;
out_early:
@@ -1953,15 +1944,18 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
int stop_sync_thread(struct netns_ipvs *ipvs, int state)
{
- struct task_struct **array;
+ struct ip_vs_sync_thread_data *ti, *tinfo;
int id;
int retc = -EINVAL;
IP_VS_DBG(7, "%s(): pid %d\n", __func__, task_pid_nr(current));
+ mutex_lock(&ipvs->sync_mutex);
if (state == IP_VS_STATE_MASTER) {
+ retc = -ESRCH;
if (!ipvs->ms)
- return -ESRCH;
+ goto err;
+ ti = ipvs->master_tinfo;
/*
* The lock synchronizes with sb_queue_tail(), so that we don't
@@ -1980,38 +1974,56 @@ int stop_sync_thread(struct netns_ipvs *ipvs, int state)
struct ipvs_master_sync_state *ms = &ipvs->ms[id];
int ret;
+ tinfo = &ti[id];
pr_info("stopping master sync thread %d ...\n",
- task_pid_nr(ms->master_thread));
+ task_pid_nr(tinfo->task));
cancel_delayed_work_sync(&ms->master_wakeup_work);
- ret = kthread_stop(ms->master_thread);
+ ret = kthread_stop(tinfo->task);
if (retc >= 0)
retc = ret;
}
kfree(ipvs->ms);
ipvs->ms = NULL;
+ ipvs->master_tinfo = NULL;
} else if (state == IP_VS_STATE_BACKUP) {
- if (!ipvs->backup_threads)
- return -ESRCH;
+ retc = -ESRCH;
+ if (!ipvs->backup_tinfo)
+ goto err;
+ ti = ipvs->backup_tinfo;
ipvs->sync_state &= ~IP_VS_STATE_BACKUP;
- array = ipvs->backup_threads;
retc = 0;
for (id = ipvs->threads_mask; id >= 0; id--) {
int ret;
+ tinfo = &ti[id];
pr_info("stopping backup sync thread %d ...\n",
- task_pid_nr(array[id]));
- ret = kthread_stop(array[id]);
+ task_pid_nr(tinfo->task));
+ ret = kthread_stop(tinfo->task);
if (retc >= 0)
retc = ret;
}
- kfree(array);
- ipvs->backup_threads = NULL;
+ ipvs->backup_tinfo = NULL;
+ } else {
+ goto err;
}
+ id = ipvs->threads_mask;
+ mutex_unlock(&ipvs->sync_mutex);
+
+ /* No more mutexes, release socks */
+ for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+ if (tinfo->sock)
+ sock_release(tinfo->sock);
+ kfree(tinfo->buf);
+ }
+ kfree(ti);
/* decrease the module use count */
ip_vs_use_count_dec();
+ return retc;
+err:
+ mutex_unlock(&ipvs->sync_mutex);
return retc;
}
@@ -2030,7 +2042,6 @@ void ip_vs_sync_net_cleanup(struct netns_ipvs *ipvs)
{
int retc;
- mutex_lock(&ipvs->sync_mutex);
retc = stop_sync_thread(ipvs, IP_VS_STATE_MASTER);
if (retc && retc != -ESRCH)
pr_err("Failed to stop Master Daemon\n");
@@ -2038,5 +2049,4 @@ void ip_vs_sync_net_cleanup(struct netns_ipvs *ipvs)
retc = stop_sync_thread(ipvs, IP_VS_STATE_BACKUP);
if (retc && retc != -ESRCH)
pr_err("Failed to stop Backup Daemon\n");
- mutex_unlock(&ipvs->sync_mutex);
}
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 071/105] rtlwifi: rtl8192cu: fix error handle when usb probe failed
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Ping-Ke Shih, syzbot+1fcc5ef45175fc774231, Larry Finger,
Kalle Valo, Sasha Levin, linux-wireless, netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Ping-Ke Shih <pkshih@realtek.com>
[ Upstream commit 6c0ed66f1a5b84e2a812c7c2d6571a5621bf3396 ]
rtl_usb_probe() must do error handle rtl_deinit_core() only if
rtl_init_core() is done, otherwise goto error_out2.
| usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
| rtl_usb: reg 0xf0, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0
| rtl8192cu: Chip version 0x10
| rtl_usb: reg 0xa, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0
| rtl_usb: Too few input end points found
| INFO: trying to register non-static key.
| the code is fine but needs lockdep annotation.
| turning off the locking correctness validator.
| CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
| Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
| Google 01/01/2011
| Workqueue: usb_hub_wq hub_event
| Call Trace:
| __dump_stack lib/dump_stack.c:77 [inline]
| dump_stack+0xe8/0x16e lib/dump_stack.c:113
| assign_lock_key kernel/locking/lockdep.c:786 [inline]
| register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
| __lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
| lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
| __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
| _raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
| rtl_c2hcmd_launcher+0xd1/0x390
| drivers/net/wireless/realtek/rtlwifi/base.c:2344
| rtl_deinit_core+0x25/0x2d0 drivers/net/wireless/realtek/rtlwifi/base.c:574
| rtl_usb_probe.cold+0x861/0xa70
| drivers/net/wireless/realtek/rtlwifi/usb.c:1093
| usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
| really_probe+0x2da/0xb10 drivers/base/dd.c:509
| driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
| __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
| bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
| __device_attach+0x223/0x3a0 drivers/base/dd.c:844
| bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
| device_add+0xad2/0x16e0 drivers/base/core.c:2106
| usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
| generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
| usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
| really_probe+0x2da/0xb10 drivers/base/dd.c:509
| driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
| __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
| bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
| __device_attach+0x223/0x3a0 drivers/base/dd.c:844
| bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
| device_add+0xad2/0x16e0 drivers/base/core.c:2106
| usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
| hub_port_connect drivers/usb/core/hub.c:5089 [inline]
| hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
| port_event drivers/usb/core/hub.c:5350 [inline]
| hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
| process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
| worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
| kthread+0x313/0x420 kernel/kthread.c:253
| ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+1fcc5ef45175fc774231@syzkaller.appspotmail.com
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/realtek/rtlwifi/usb.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtlwifi/usb.c b/drivers/net/wireless/realtek/rtlwifi/usb.c
index 820c42ff5384..2401c8bdb211 100644
--- a/drivers/net/wireless/realtek/rtlwifi/usb.c
+++ b/drivers/net/wireless/realtek/rtlwifi/usb.c
@@ -1099,13 +1099,13 @@ int rtl_usb_probe(struct usb_interface *intf,
rtlpriv->cfg->ops->read_eeprom_info(hw);
err = _rtl_usb_init(hw);
if (err)
- goto error_out;
+ goto error_out2;
rtl_usb_init_sw(hw);
/* Init mac80211 sw */
err = rtl_init_core(hw);
if (err) {
pr_err("Can't allocate sw for mac80211\n");
- goto error_out;
+ goto error_out2;
}
if (rtlpriv->cfg->ops->init_sw_vars(hw)) {
pr_err("Can't init_sw_vars\n");
@@ -1126,6 +1126,7 @@ int rtl_usb_probe(struct usb_interface *intf,
error_out:
rtl_deinit_core(hw);
+error_out2:
_rtl_usb_io_handler_release(hw);
usb_put_dev(udev);
complete(&rtlpriv->firmware_loading_complete);
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 060/105] ipvs: defer hook registration to avoid leaks
From: Sasha Levin @ 2019-07-15 14:27 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Julian Anastasov, syzbot+722da59ccb264bc19910, Simon Horman,
Pablo Neira Ayuso, Sasha Levin, netdev, lvs-devel,
netfilter-devel, coreteam
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Julian Anastasov <ja@ssi.bg>
[ Upstream commit cf47a0b882a4e5f6b34c7949d7b293e9287f1972 ]
syzkaller reports for memory leak when registering hooks [1]
As we moved the nf_unregister_net_hooks() call into
__ip_vs_dev_cleanup(), defer the nf_register_net_hooks()
call, so that hooks are allocated and freed from same
pernet_operations (ipvs_core_dev_ops).
[1]
BUG: memory leak
unreferenced object 0xffff88810acd8a80 (size 96):
comm "syz-executor073", pid 7254, jiffies 4294950560 (age 22.250s)
hex dump (first 32 bytes):
02 00 00 00 00 00 00 00 50 8b bb 82 ff ff ff ff ........P.......
00 00 00 00 00 00 00 00 00 77 bb 82 ff ff ff ff .........w......
backtrace:
[<0000000013db61f1>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
[<0000000013db61f1>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<0000000013db61f1>] slab_alloc_node mm/slab.c:3269 [inline]
[<0000000013db61f1>] kmem_cache_alloc_node_trace+0x15b/0x2a0 mm/slab.c:3597
[<000000001a27307d>] __do_kmalloc_node mm/slab.c:3619 [inline]
[<000000001a27307d>] __kmalloc_node+0x38/0x50 mm/slab.c:3627
[<0000000025054add>] kmalloc_node include/linux/slab.h:590 [inline]
[<0000000025054add>] kvmalloc_node+0x4a/0xd0 mm/util.c:431
[<0000000050d1bc00>] kvmalloc include/linux/mm.h:637 [inline]
[<0000000050d1bc00>] kvzalloc include/linux/mm.h:645 [inline]
[<0000000050d1bc00>] allocate_hook_entries_size+0x3b/0x60 net/netfilter/core.c:61
[<00000000e8abe142>] nf_hook_entries_grow+0xae/0x270 net/netfilter/core.c:128
[<000000004b94797c>] __nf_register_net_hook+0x9a/0x170 net/netfilter/core.c:337
[<00000000d1545cbc>] nf_register_net_hook+0x34/0xc0 net/netfilter/core.c:464
[<00000000876c9b55>] nf_register_net_hooks+0x53/0xc0 net/netfilter/core.c:480
[<000000002ea868e0>] __ip_vs_init+0xe8/0x170 net/netfilter/ipvs/ip_vs_core.c:2280
[<000000002eb2d451>] ops_init+0x4c/0x140 net/core/net_namespace.c:130
[<000000000284ec48>] setup_net+0xde/0x230 net/core/net_namespace.c:316
[<00000000a70600fa>] copy_net_ns+0xf0/0x1e0 net/core/net_namespace.c:439
[<00000000ff26c15e>] create_new_namespaces+0x141/0x2a0 kernel/nsproxy.c:107
[<00000000b103dc79>] copy_namespaces+0xa1/0xe0 kernel/nsproxy.c:165
[<000000007cc008a2>] copy_process.part.0+0x11fd/0x2150 kernel/fork.c:2035
[<00000000c344af7c>] copy_process kernel/fork.c:1800 [inline]
[<00000000c344af7c>] _do_fork+0x121/0x4f0 kernel/fork.c:2369
Reported-by: syzbot+722da59ccb264bc19910@syzkaller.appspotmail.com
Fixes: 719c7d563c17 ("ipvs: Fix use-after-free in ip_vs_in")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/netfilter/ipvs/ip_vs_core.c | 21 ++++++++++++++-------
1 file changed, 14 insertions(+), 7 deletions(-)
diff --git a/net/netfilter/ipvs/ip_vs_core.c b/net/netfilter/ipvs/ip_vs_core.c
index ee97ce176b9a..2156571455db 100644
--- a/net/netfilter/ipvs/ip_vs_core.c
+++ b/net/netfilter/ipvs/ip_vs_core.c
@@ -2206,7 +2206,6 @@ static const struct nf_hook_ops ip_vs_ops[] = {
static int __net_init __ip_vs_init(struct net *net)
{
struct netns_ipvs *ipvs;
- int ret;
ipvs = net_generic(net, ip_vs_net_id);
if (ipvs == NULL)
@@ -2238,17 +2237,11 @@ static int __net_init __ip_vs_init(struct net *net)
if (ip_vs_sync_net_init(ipvs) < 0)
goto sync_fail;
- ret = nf_register_net_hooks(net, ip_vs_ops, ARRAY_SIZE(ip_vs_ops));
- if (ret < 0)
- goto hook_fail;
-
return 0;
/*
* Error handling
*/
-hook_fail:
- ip_vs_sync_net_cleanup(ipvs);
sync_fail:
ip_vs_conn_net_cleanup(ipvs);
conn_fail:
@@ -2278,6 +2271,19 @@ static void __net_exit __ip_vs_cleanup(struct net *net)
net->ipvs = NULL;
}
+static int __net_init __ip_vs_dev_init(struct net *net)
+{
+ int ret;
+
+ ret = nf_register_net_hooks(net, ip_vs_ops, ARRAY_SIZE(ip_vs_ops));
+ if (ret < 0)
+ goto hook_fail;
+ return 0;
+
+hook_fail:
+ return ret;
+}
+
static void __net_exit __ip_vs_dev_cleanup(struct net *net)
{
struct netns_ipvs *ipvs = net_ipvs(net);
@@ -2297,6 +2303,7 @@ static struct pernet_operations ipvs_core_ops = {
};
static struct pernet_operations ipvs_core_dev_ops = {
+ .init = __ip_vs_dev_init,
.exit = __ip_vs_dev_cleanup,
};
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 01/73] ath10k: Do not send probe response template for mesh
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Surabhi Vishnoi, Kalle Valo, Sasha Levin, ath10k, linux-wireless,
netdev
From: Surabhi Vishnoi <svishnoi@codeaurora.org>
[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index fb632a454fc2..1588fe8110d0 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1596,6 +1596,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
return 0;
+ /* For mesh, probe response and beacon share the same template */
+ if (ieee80211_vif_is_mesh(vif))
+ return 0;
+
prb = ieee80211_proberesp_get(hw, vif);
if (!prb) {
ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 02/73] ath9k: Check for errors when reading SREV register
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Tim Schumacher, Kalle Valo, Sasha Levin, linux-wireless, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Tim Schumacher <timschumi@gmx.de>
[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
1 file changed, 23 insertions(+), 9 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 951bac2caf12..e7fca78cdd96 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -250,8 +250,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
/* Chip Revisions */
/******************/
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
{
+ u32 srev;
u32 val;
if (ah->get_mac_revision)
@@ -267,25 +268,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
val = REG_READ(ah, AR_SREV);
ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
}
- return;
+ return true;
case AR9300_DEVID_AR9340:
ah->hw_version.macVersion = AR_SREV_VERSION_9340;
- return;
+ return true;
case AR9300_DEVID_QCA955X:
ah->hw_version.macVersion = AR_SREV_VERSION_9550;
- return;
+ return true;
case AR9300_DEVID_AR953X:
ah->hw_version.macVersion = AR_SREV_VERSION_9531;
- return;
+ return true;
case AR9300_DEVID_QCA956X:
ah->hw_version.macVersion = AR_SREV_VERSION_9561;
- return;
+ return true;
}
- val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+ srev = REG_READ(ah, AR_SREV);
+
+ if (srev == -EIO) {
+ ath_err(ath9k_hw_common(ah),
+ "Failed to read SREV register");
+ return false;
+ }
+
+ val = srev & AR_SREV_ID;
if (val == 0xFF) {
- val = REG_READ(ah, AR_SREV);
+ val = srev;
ah->hw_version.macVersion =
(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -304,6 +313,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
ah->is_pciexpress = true;
}
+
+ return true;
}
/************************************/
@@ -557,7 +568,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
struct ath_common *common = ath9k_hw_common(ah);
int r = 0;
- ath9k_hw_read_revisions(ah);
+ if (!ath9k_hw_read_revisions(ah)) {
+ ath_err(common, "Could not read hardware revisions");
+ return -EOPNOTSUPP;
+ }
switch (ah->hw_version.macVersion) {
case AR_SREV_VERSION_5416_PCI:
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 04/73] ath: DFS JP domain W56 fixed pulse type 3 RADAR detection
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Anilkumar Kolli, Tamizh chelvam, Kalle Valo, Sasha Levin,
linux-wireless, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Anilkumar Kolli <akolli@codeaurora.org>
[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]
Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.
Tested ath10k hw and fw:
* QCA9888(10.4-3.5.1-00052)
* QCA4019(10.4-3.2.1.1-00017)
* QCA9984(10.4-3.6-00104)
* QCA988X(10.2.4-1.0-00041)
Tested ath9k hw: AR9300
Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/dfs_pattern_detector.c b/drivers/net/wireless/ath/dfs_pattern_detector.c
index 4100ffd42a43..78146607f16e 100644
--- a/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ b/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
- JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+ JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 05/73] batman-adv: fix for leaked TVLV handler.
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Jeremy Sowden, syzbot+d454a826e670502484b8, Simon Wunderlich,
Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Jeremy Sowden <jeremy@azazel.net>
[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]
A handler for BATADV_TVLV_ROAM was being registered when the
translation-table was initialized, but not unregistered when the
translation-table was freed. Unregister it.
Fixes: 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/batman-adv/translation-table.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/net/batman-adv/translation-table.c b/net/batman-adv/translation-table.c
index af4a02ad8503..1fab9bcf535d 100644
--- a/net/batman-adv/translation-table.c
+++ b/net/batman-adv/translation-table.c
@@ -3700,6 +3700,8 @@ static void batadv_tt_purge(struct work_struct *work)
void batadv_tt_free(struct batadv_priv *bat_priv)
{
+ batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_ROAM, 1);
+
batadv_tvlv_container_unregister(bat_priv, BATADV_TVLV_TT, 1);
batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_TT, 1);
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 094/105] net: usb: asix: init MAC address buffers
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Phong Tran, syzbot+8a3fc6674bbc3978ed4e, David S . Miller,
Sasha Levin, linux-usb, netdev, clang-built-linux
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Phong Tran <tranmanphong@gmail.com>
[ Upstream commit 78226f6eaac80bf30256a33a4926c194ceefdf36 ]
This is for fixing bug KMSAN: uninit-value in ax88772_bind
Tested by
https://groups.google.com/d/msg/syzkaller-bugs/aFQurGotng4/eB_HlNhhCwAJ
Reported-by: syzbot+8a3fc6674bbc3978ed4e@syzkaller.appspotmail.com
syzbot found the following crash on:
HEAD commit: f75e4cfe kmsan: use kmsan_handle_urb() in urb.c
git tree: kmsan
console output: https://syzkaller.appspot.com/x/log.txt?x=136d720ea00000
kernel config:
https://syzkaller.appspot.com/x/.config?x=602468164ccdc30a
dashboard link:
https://syzkaller.appspot.com/bug?extid=8a3fc6674bbc3978ed4e
compiler: clang version 9.0.0 (/home/glider/llvm/clang
06d00afa61eef8f7f501ebdb4e8612ea43ec2d78)
syz repro:
https://syzkaller.appspot.com/x/repro.syz?x=12788316a00000
C reproducer: https://syzkaller.appspot.com/x/repro.c?x=120359aaa00000
==================================================================
BUG: KMSAN: uninit-value in is_valid_ether_addr
include/linux/etherdevice.h:200 [inline]
BUG: KMSAN: uninit-value in asix_set_netdev_dev_addr
drivers/net/usb/asix_devices.c:73 [inline]
BUG: KMSAN: uninit-value in ax88772_bind+0x93d/0x11e0
drivers/net/usb/asix_devices.c:724
CPU: 0 PID: 3348 Comm: kworker/0:2 Not tainted 5.1.0+ #1
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
is_valid_ether_addr include/linux/etherdevice.h:200 [inline]
asix_set_netdev_dev_addr drivers/net/usb/asix_devices.c:73 [inline]
ax88772_bind+0x93d/0x11e0 drivers/net/usb/asix_devices.c:724
usbnet_probe+0x10f5/0x3940 drivers/net/usb/usbnet.c:1728
usb_probe_interface+0xd66/0x1320 drivers/usb/core/driver.c:361
really_probe+0xdae/0x1d80 drivers/base/dd.c:513
driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671
__device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778
bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454
__device_attach+0x454/0x730 drivers/base/dd.c:844
device_initial_probe+0x4a/0x60 drivers/base/dd.c:891
bus_probe_device+0x137/0x390 drivers/base/bus.c:514
device_add+0x288d/0x30e0 drivers/base/core.c:2106
usb_set_configuration+0x30dc/0x3750 drivers/usb/core/message.c:2027
generic_probe+0xe7/0x280 drivers/usb/core/generic.c:210
usb_probe_device+0x14c/0x200 drivers/usb/core/driver.c:266
really_probe+0xdae/0x1d80 drivers/base/dd.c:513
driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671
__device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778
bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454
__device_attach+0x454/0x730 drivers/base/dd.c:844
device_initial_probe+0x4a/0x60 drivers/base/dd.c:891
bus_probe_device+0x137/0x390 drivers/base/bus.c:514
device_add+0x288d/0x30e0 drivers/base/core.c:2106
usb_new_device+0x23e5/0x2ff0 drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x48d1/0x7290 drivers/usb/core/hub.c:5432
process_one_work+0x1572/0x1f00 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x189c/0x2460 kernel/workqueue.c:2417
kthread+0x4b5/0x4f0 kernel/kthread.c:254
ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:355
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/usb/asix_devices.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index d0c0ac0c3519..9b751d4bd327 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -238,7 +238,7 @@ static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits)
static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
{
int ret = 0;
- u8 buf[ETH_ALEN];
+ u8 buf[ETH_ALEN] = {0};
int i;
unsigned long gpio_bits = dev->driver_info->data;
@@ -689,7 +689,7 @@ static int asix_resume(struct usb_interface *intf)
static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
{
int ret, i;
- u8 buf[ETH_ALEN], chipcode = 0;
+ u8 buf[ETH_ALEN] = {0}, chipcode = 0;
u32 phyid;
struct asix_common_private *priv;
@@ -1065,7 +1065,7 @@ static const struct net_device_ops ax88178_netdev_ops = {
static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
{
int ret;
- u8 buf[ETH_ALEN];
+ u8 buf[ETH_ALEN] = {0};
usbnet_get_endpoints(dev,intf);
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.14 097/105] Bluetooth: 6lowpan: search for destination address in all peers
From: Sasha Levin @ 2019-07-15 14:28 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Josua Mayer, Jukka Rissanen, Michael Scott, Marcel Holtmann,
Sasha Levin, linux-bluetooth, netdev
In-Reply-To: <20190715142839.9896-1-sashal@kernel.org>
From: Josua Mayer <josua.mayer@jm0.eu>
[ Upstream commit b188b03270b7f8568fc714101ce82fbf5e811c5a ]
Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.
For one peer, no checks are performed to see if it is meant to receive
packets for a given address.
As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/bluetooth/6lowpan.c | 14 ++++++++++----
1 file changed, 10 insertions(+), 4 deletions(-)
diff --git a/net/bluetooth/6lowpan.c b/net/bluetooth/6lowpan.c
index 4e2576fc0c59..357475cceec6 100644
--- a/net/bluetooth/6lowpan.c
+++ b/net/bluetooth/6lowpan.c
@@ -187,10 +187,16 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_btle_dev *dev,
}
if (!rt) {
- nexthop = &lowpan_cb(skb)->gw;
-
- if (ipv6_addr_any(nexthop))
- return NULL;
+ if (ipv6_addr_any(&lowpan_cb(skb)->gw)) {
+ /* There is neither route nor gateway,
+ * probably the destination is a direct peer.
+ */
+ nexthop = daddr;
+ } else {
+ /* There is a known gateway
+ */
+ nexthop = &lowpan_cb(skb)->gw;
+ }
} else {
nexthop = rt6_nexthop(rt, daddr);
--
2.20.1
^ permalink raw reply related
* [PATCH 1/9] rcu/update: Remove useless check for debug_locks (v1)
From: Joel Fernandes (Google) @ 2019-07-15 14:36 UTC (permalink / raw)
To: linux-kernel
Cc: Joel Fernandes (Google), Alexey Kuznetsov, Bjorn Helgaas,
Borislav Petkov, c0d1n61at3, David S. Miller, edumazet,
Greg Kroah-Hartman, Hideaki YOSHIFUJI, H. Peter Anvin,
Ingo Molnar, Jonathan Corbet, Josh Triplett, keescook,
kernel-hardening, kernel-team, Lai Jiangshan, Len Brown,
linux-acpi, linux-doc, linux-pci, linux-pm, Mathieu Desnoyers,
neilb, netdev, Oleg Nesterov, Paul E. McKenney, Pavel Machek,
peterz, Rafael J. Wysocki, Rasmus Villemoes, rcu, Steven Rostedt,
Tejun Heo, Thomas Gleixner, will,
maintainer:X86 ARCHITECTURE (32-BIT AND 64-BIT)
In-Reply-To: <20190715143705.117908-1-joel@joelfernandes.org>
In rcu_read_lock_sched_held(), debug_locks can never be true at the
point we check it because we already check debug_locks in
debug_lockdep_rcu_enabled() in the beginning. Remove the check.
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
---
kernel/rcu/update.c | 6 +-----
1 file changed, 1 insertion(+), 5 deletions(-)
diff --git a/kernel/rcu/update.c b/kernel/rcu/update.c
index 61df2bf08563..9dd5aeef6e70 100644
--- a/kernel/rcu/update.c
+++ b/kernel/rcu/update.c
@@ -93,17 +93,13 @@ module_param(rcu_normal_after_boot, int, 0);
*/
int rcu_read_lock_sched_held(void)
{
- int lockdep_opinion = 0;
-
if (!debug_lockdep_rcu_enabled())
return 1;
if (!rcu_is_watching())
return 0;
if (!rcu_lockdep_current_cpu_online())
return 0;
- if (debug_locks)
- lockdep_opinion = lock_is_held(&rcu_sched_lock_map);
- return lockdep_opinion || !preemptible();
+ return lock_is_held(&rcu_sched_lock_map) || !preemptible();
}
EXPORT_SYMBOL(rcu_read_lock_sched_held);
#endif
--
2.22.0.510.g264f2c817a-goog
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 17/73] Revert "e1000e: fix cyclic resets at link up with active tx"
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Konstantin Khlebnikov, Joseph Yasi, Aaron Brown,
Oleksandr Natalenko, Jeff Kirsher, Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
[ Upstream commit caff422ea81e144842bc44bab408d85ac449377b ]
This reverts commit 0f9e980bf5ee1a97e2e401c846b2af989eb21c61.
That change cased false-positive warning about hardware hang:
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
TDH <0>
TDT <1>
next_to_use <1>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <fffba7a7>
next_to_watch <0>
jiffies <fffbb140>
next_to_watch.status <0>
MAC Status <40080080>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Besides warning everything works fine.
Original issue will be fixed property in following patch.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/ethernet/intel/e1000e/netdev.c | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 8bbedfc9c48f..f56f8b6e2378 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -5291,13 +5291,8 @@ static void e1000_watchdog_task(struct work_struct *work)
/* 8000ES2LAN requires a Rx packet buffer work-around
* on link down event; reset the controller to flush
* the Rx packet buffer.
- *
- * If the link is lost the controller stops DMA, but
- * if there is queued Tx work it cannot be done. So
- * reset the controller to flush the Tx packet buffers.
*/
- if ((adapter->flags & FLAG_RX_NEEDS_RESTART) ||
- e1000_desc_unused(tx_ring) + 1 < tx_ring->count)
+ if (adapter->flags & FLAG_RX_NEEDS_RESTART)
adapter->flags |= FLAG_RESTART_NOW;
else
pm_schedule_suspend(netdev->dev.parent,
@@ -5320,6 +5315,14 @@ static void e1000_watchdog_task(struct work_struct *work)
adapter->gotc_old = adapter->stats.gotc;
spin_unlock(&adapter->stats64_lock);
+ /* If the link is lost the controller stops DMA, but
+ * if there is queued Tx work it cannot be done. So
+ * reset the controller to flush the Tx packet buffers.
+ */
+ if (!netif_carrier_ok(netdev) &&
+ (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
+ adapter->flags |= FLAG_RESTART_NOW;
+
/* If reset is necessary, do it outside of interrupt context. */
if (adapter->flags & FLAG_RESTART_NOW) {
schedule_work(&adapter->reset_task);
--
2.20.1
^ permalink raw reply related
* [PATCH 7/9] x86/pci: Pass lockdep condition to pcm_mmcfg_list iterator (v1)
From: Joel Fernandes (Google) @ 2019-07-15 14:37 UTC (permalink / raw)
To: linux-kernel
Cc: Joel Fernandes (Google), Alexey Kuznetsov, Bjorn Helgaas,
Borislav Petkov, c0d1n61at3, David S. Miller, edumazet,
Greg Kroah-Hartman, Hideaki YOSHIFUJI, H. Peter Anvin,
Ingo Molnar, Jonathan Corbet, Josh Triplett, keescook,
kernel-hardening, kernel-team, Lai Jiangshan, Len Brown,
linux-acpi, linux-doc, linux-pci, linux-pm, Mathieu Desnoyers,
neilb, netdev, Oleg Nesterov, Paul E. McKenney, Pavel Machek,
peterz, Rafael J. Wysocki, Rasmus Villemoes, rcu, Steven Rostedt,
Tejun Heo, Thomas Gleixner, will,
maintainer:X86 ARCHITECTURE (32-BIT AND 64-BIT)
In-Reply-To: <20190715143705.117908-1-joel@joelfernandes.org>
The pcm_mmcfg_list is traversed with list_for_each_entry_rcu without a
reader-lock held, because the pci_mmcfg_lock is already held. Make this
known to the list macro so that it fixes new lockdep warnings that
trigger due to lockdep checks added to list_for_each_entry_rcu().
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
---
arch/x86/pci/mmconfig-shared.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/x86/pci/mmconfig-shared.c b/arch/x86/pci/mmconfig-shared.c
index 7389db538c30..6fa42e9c4e6f 100644
--- a/arch/x86/pci/mmconfig-shared.c
+++ b/arch/x86/pci/mmconfig-shared.c
@@ -29,6 +29,7 @@
static bool pci_mmcfg_running_state;
static bool pci_mmcfg_arch_init_failed;
static DEFINE_MUTEX(pci_mmcfg_lock);
+#define pci_mmcfg_lock_held() lock_is_held(&(pci_mmcfg_lock).dep_map)
LIST_HEAD(pci_mmcfg_list);
@@ -54,7 +55,7 @@ static void list_add_sorted(struct pci_mmcfg_region *new)
struct pci_mmcfg_region *cfg;
/* keep list sorted by segment and starting bus number */
- list_for_each_entry_rcu(cfg, &pci_mmcfg_list, list) {
+ list_for_each_entry_rcu(cfg, &pci_mmcfg_list, list, pci_mmcfg_lock_held()) {
if (cfg->segment > new->segment ||
(cfg->segment == new->segment &&
cfg->start_bus >= new->start_bus)) {
@@ -118,7 +119,7 @@ struct pci_mmcfg_region *pci_mmconfig_lookup(int segment, int bus)
{
struct pci_mmcfg_region *cfg;
- list_for_each_entry_rcu(cfg, &pci_mmcfg_list, list)
+ list_for_each_entry_rcu(cfg, &pci_mmcfg_list, list, pci_mmcfg_lock_held())
if (cfg->segment == segment &&
cfg->start_bus <= bus && bus <= cfg->end_bus)
return cfg;
--
2.22.0.510.g264f2c817a-goog
^ permalink raw reply related
* [PATCH 9/9] doc: Update documentation about list_for_each_entry_rcu (v1)
From: Joel Fernandes (Google) @ 2019-07-15 14:37 UTC (permalink / raw)
To: linux-kernel
Cc: Joel Fernandes (Google), Alexey Kuznetsov, Bjorn Helgaas,
Borislav Petkov, c0d1n61at3, David S. Miller, edumazet,
Greg Kroah-Hartman, Hideaki YOSHIFUJI, H. Peter Anvin,
Ingo Molnar, Jonathan Corbet, Josh Triplett, keescook,
kernel-hardening, kernel-team, Lai Jiangshan, Len Brown,
linux-acpi, linux-doc, linux-pci, linux-pm, Mathieu Desnoyers,
neilb, netdev, Oleg Nesterov, Paul E. McKenney, Pavel Machek,
peterz, Rafael J. Wysocki, Rasmus Villemoes, rcu, Steven Rostedt,
Tejun Heo, Thomas Gleixner, will,
maintainer:X86 ARCHITECTURE (32-BIT AND 64-BIT)
In-Reply-To: <20190715143705.117908-1-joel@joelfernandes.org>
This patch updates the documentation with information about
usage of lockdep with list_for_each_entry_rcu().
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
---
Documentation/RCU/lockdep.txt | 15 +++++++++++----
Documentation/RCU/whatisRCU.txt | 9 ++++++++-
2 files changed, 19 insertions(+), 5 deletions(-)
diff --git a/Documentation/RCU/lockdep.txt b/Documentation/RCU/lockdep.txt
index da51d3068850..3d967df3a801 100644
--- a/Documentation/RCU/lockdep.txt
+++ b/Documentation/RCU/lockdep.txt
@@ -96,7 +96,14 @@ other flavors of rcu_dereference(). On the other hand, it is illegal
to use rcu_dereference_protected() if either the RCU-protected pointer
or the RCU-protected data that it points to can change concurrently.
-There are currently only "universal" versions of the rcu_assign_pointer()
-and RCU list-/tree-traversal primitives, which do not (yet) check for
-being in an RCU read-side critical section. In the future, separate
-versions of these primitives might be created.
+Similar to rcu_dereference_protected, The RCU list and hlist traversal
+primitives also check for whether there are called from within a reader
+section. However, an optional lockdep expression can be passed to them as
+the last argument in case they are called under other non-RCU protection.
+
+For example, the workqueue for_each_pwq() macro is implemented as follows.
+It is safe to call for_each_pwq() outside a reader section but under protection
+of wq->mutex:
+#define for_each_pwq(pwq, wq)
+ list_for_each_entry_rcu((pwq), &(wq)->pwqs, pwqs_node,
+ lock_is_held(&(wq->mutex).dep_map))
diff --git a/Documentation/RCU/whatisRCU.txt b/Documentation/RCU/whatisRCU.txt
index 7e1a8721637a..00fe77ede1e2 100644
--- a/Documentation/RCU/whatisRCU.txt
+++ b/Documentation/RCU/whatisRCU.txt
@@ -290,7 +290,7 @@ rcu_dereference()
at any time, including immediately after the rcu_dereference().
And, again like rcu_assign_pointer(), rcu_dereference() is
typically used indirectly, via the _rcu list-manipulation
- primitives, such as list_for_each_entry_rcu().
+ primitives, such as list_for_each_entry_rcu() [2].
[1] The variant rcu_dereference_protected() can be used outside
of an RCU read-side critical section as long as the usage is
@@ -305,6 +305,13 @@ rcu_dereference()
a lockdep splat is emitted. See RCU/Design/Requirements/Requirements.html
and the API's code comments for more details and example usage.
+ [2] In case the list_for_each_entry_rcu() primitive is intended
+ to be used outside of an RCU reader section such as when
+ protected by a lock, then an additional lockdep expression can be
+ passed as the last argument to it so that RCU lockdep checking code
+ knows that the dereference of the list pointers are safe. If the
+ indicated protection is not provided, a lockdep splat is emitted.
+
The following diagram shows how each API communicates among the
reader, updater, and reclaimer.
--
2.22.0.510.g264f2c817a-goog
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 28/73] net: fec: Do not use netdev messages too early
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable; +Cc: Fabio Estevam, David S . Miller, Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Fabio Estevam <festevam@gmail.com>
[ Upstream commit a19a0582363b9a5f8ba812f34f1b8df394898780 ]
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/ethernet/freescale/fec_main.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 1eb34109b207..92ea760c4822 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1685,10 +1685,10 @@ static void fec_get_mac(struct net_device *ndev)
*/
if (!is_valid_ether_addr(iap)) {
/* Report it and use a random ethernet address instead */
- netdev_err(ndev, "Invalid MAC address: %pM\n", iap);
+ dev_err(&fep->pdev->dev, "Invalid MAC address: %pM\n", iap);
eth_hw_addr_random(ndev);
- netdev_info(ndev, "Using random MAC address: %pM\n",
- ndev->dev_addr);
+ dev_info(&fep->pdev->dev, "Using random MAC address: %pM\n",
+ ndev->dev_addr);
return;
}
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 29/73] net: axienet: Fix race condition causing TX hang
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Robert Hancock, David S . Miller, Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Robert Hancock <hancock@sedsystems.ca>
[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
.../net/ethernet/xilinx/xilinx_axienet_main.c | 20 ++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index a8afc92cbfca..5f21ddff9e0f 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -612,6 +612,10 @@ static void axienet_start_xmit_done(struct net_device *ndev)
ndev->stats.tx_packets += packets;
ndev->stats.tx_bytes += size;
+
+ /* Matches barrier in axienet_start_xmit */
+ smp_mb();
+
netif_wake_queue(ndev);
}
@@ -666,9 +670,19 @@ static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
if (axienet_check_tx_bd_space(lp, num_frag)) {
- if (!netif_queue_stopped(ndev))
- netif_stop_queue(ndev);
- return NETDEV_TX_BUSY;
+ if (netif_queue_stopped(ndev))
+ return NETDEV_TX_BUSY;
+
+ netif_stop_queue(ndev);
+
+ /* Matches barrier in axienet_start_xmit_done */
+ smp_mb();
+
+ /* Space might have just been freed - check again */
+ if (axienet_check_tx_bd_space(lp, num_frag))
+ return NETDEV_TX_BUSY;
+
+ netif_wake_queue(ndev);
}
if (skb->ip_summed == CHECKSUM_PARTIAL) {
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 39/73] xfrm: fix sa selector validation
From: Sasha Levin @ 2019-07-15 14:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Nicolas Dichtel, Anirudh Gupta, Herbert Xu, Steffen Klassert,
Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Nicolas Dichtel <nicolas.dichtel@6wind.com>
[ Upstream commit b8d6d0079757cbd1b69724cfd1c08e2171c68cee ]
After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4
In fact, the selector is not mandatory, allow the user to provide an empty
selector.
Fixes: b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation")
CC: Anirudh Gupta <anirudh.gupta@sophos.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/xfrm/xfrm_user.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/net/xfrm/xfrm_user.c b/net/xfrm/xfrm_user.c
index df4b7fc721f6..f3e9d500fa5a 100644
--- a/net/xfrm/xfrm_user.c
+++ b/net/xfrm/xfrm_user.c
@@ -166,6 +166,9 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
}
switch (p->sel.family) {
+ case AF_UNSPEC:
+ break;
+
case AF_INET:
if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
goto out;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 44/73] ipsec: select crypto ciphers for xfrm_algo
From: Sasha Levin @ 2019-07-15 14:36 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Arnd Bergmann, Herbert Xu, Steffen Klassert, Sasha Levin, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Arnd Bergmann <arnd@arndb.de>
[ Upstream commit 597179b0ba550bd83fab1a9d57c42a9343c58514 ]
kernelci.org reports failed builds on arc because of what looks
like an old missed 'select' statement:
net/xfrm/xfrm_algo.o: In function `xfrm_probe_algs':
xfrm_algo.c:(.text+0x1e8): undefined reference to `crypto_has_ahash'
I don't see this in randconfig builds on other architectures, but
it's fairly clear we want to select the hash code for it, like we
do for all its other users. As Herbert points out, CRYPTO_BLKCIPHER
is also required even though it has not popped up in build tests.
Fixes: 17bc19702221 ("ipsec: Use skcipher and ahash when probing algorithms")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/xfrm/Kconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/net/xfrm/Kconfig b/net/xfrm/Kconfig
index bda1a13628a8..c09336b5a028 100644
--- a/net/xfrm/Kconfig
+++ b/net/xfrm/Kconfig
@@ -9,6 +9,8 @@ config XFRM_ALGO
tristate
select XFRM
select CRYPTO
+ select CRYPTO_HASH
+ select CRYPTO_BLKCIPHER
config XFRM_USER
tristate "Transformation user configuration interface"
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 51/73] mt7601u: do not schedule rx_tasklet when the device has been disconnected
From: Sasha Levin @ 2019-07-15 14:36 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Lorenzo Bianconi, Kalle Valo, Sasha Levin, linux-wireless, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Lorenzo Bianconi <lorenzo@kernel.org>
[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]
Do not schedule rx_tasklet when the usb dongle is disconnected.
Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb
can run concurrently with urb completion and we can unlink urbs from rx
ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.
[ 24.921354] usb 3-14: USB disconnect, device number 7
[ 24.921593] ------------[ cut here ]------------
[ 24.921594] RX urb mismatch
[ 24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[ 24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G OE 4.19.31-041931-generic #201903231635
[ 24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014
[ 24.921782] Workqueue: usb_hub_wq hub_event
[ 24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[ 24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086
[ 24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006
[ 24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420
[ 24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8
[ 24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c
[ 24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000
[ 24.921807] FS: 0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000
[ 24.921808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0
[ 24.921809] Call Trace:
[ 24.921812] <IRQ>
[ 24.921819] __usb_hcd_giveback_urb+0x8b/0x140
[ 24.921821] usb_hcd_giveback_urb+0xca/0xe0
[ 24.921828] xhci_giveback_urb_in_irq.isra.42+0x82/0xf0
[ 24.921834] handle_cmd_completion+0xe02/0x10d0
[ 24.921837] xhci_irq+0x274/0x4a0
[ 24.921838] xhci_msi_irq+0x11/0x20
[ 24.921851] __handle_irq_event_percpu+0x44/0x190
[ 24.921856] handle_irq_event_percpu+0x32/0x80
[ 24.921861] handle_irq_event+0x3b/0x5a
[ 24.921867] handle_edge_irq+0x80/0x190
[ 24.921874] handle_irq+0x20/0x30
[ 24.921889] do_IRQ+0x4e/0xe0
[ 24.921891] common_interrupt+0xf/0xf
[ 24.921892] </IRQ>
[ 24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180
[ 24.921354] usb 3-14: USB disconnect, device number 7
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++----------
1 file changed, 18 insertions(+), 15 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index a8bc064bc14f..838ad9a4be51 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)
struct mt7601u_rx_queue *q = &dev->rx_q;
unsigned long flags;
- spin_lock_irqsave(&dev->rx_lock, flags);
+ /* do no schedule rx tasklet if urb has been unlinked
+ * or the device has been removed
+ */
+ switch (urb->status) {
+ case -ECONNRESET:
+ case -ESHUTDOWN:
+ case -ENOENT:
+ return;
+ default:
+ dev_err_ratelimited(dev->dev, "rx urb failed: %d\n",
+ urb->status);
+ /* fall through */
+ case 0:
+ break;
+ }
- if (mt7601u_urb_has_error(urb))
- dev_err(dev->dev, "Error: RX urb failed:%d\n", urb->status);
+ spin_lock_irqsave(&dev->rx_lock, flags);
if (WARN_ONCE(q->e[q->end].urb != urb, "RX urb mismatch"))
goto out;
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,
static void mt7601u_kill_rx(struct mt7601u_dev *dev)
{
int i;
- unsigned long flags;
- spin_lock_irqsave(&dev->rx_lock, flags);
-
- for (i = 0; i < dev->rx_q.entries; i++) {
- int next = dev->rx_q.end;
-
- spin_unlock_irqrestore(&dev->rx_lock, flags);
- usb_poison_urb(dev->rx_q.e[next].urb);
- spin_lock_irqsave(&dev->rx_lock, flags);
- }
-
- spin_unlock_irqrestore(&dev->rx_lock, flags);
+ for (i = 0; i < dev->rx_q.entries; i++)
+ usb_poison_urb(dev->rx_q.e[i].urb);
}
static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 65/73] iwlwifi: mvm: Drop large non sta frames
From: Sasha Levin @ 2019-07-15 14:36 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Andrei Otcheretianski, Luca Coelho, Sasha Levin, linux-wireless,
netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[ Upstream commit ac70499ee97231a418dc1a4d6c9dc102e8f64631 ]
In some buggy scenarios we could possible attempt to transmit frames larger
than maximum MSDU size. Since our devices don't know how to handle this,
it may result in asserts, hangs etc.
This can happen, for example, when we receive a large multicast frame
and try to transmit it back to the air in AP mode.
Since in a legal scenario this should never happen, drop such frames and
warn about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
index bd7ff562d82d..1aa74b87599f 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -551,6 +551,9 @@ int iwl_mvm_tx_skb_non_sta(struct iwl_mvm *mvm, struct sk_buff *skb)
memcpy(&info, skb->cb, sizeof(info));
+ if (WARN_ON_ONCE(skb->len > IEEE80211_MAX_DATA_LEN + hdrlen))
+ return -1;
+
if (WARN_ON_ONCE(info.flags & IEEE80211_TX_CTL_AMPDU))
return -1;
--
2.20.1
^ permalink raw reply related
* [PATCH AUTOSEL 4.9 70/73] Bluetooth: Check state in l2cap_disconnect_rsp
From: Sasha Levin @ 2019-07-15 14:36 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Matias Karhumaa, Matti Kamunen, Ari Timonen, Marcel Holtmann,
Sasha Levin, linux-bluetooth, netdev
In-Reply-To: <20190715143629.10893-1-sashal@kernel.org>
From: Matias Karhumaa <matias.karhumaa@gmail.com>
[ Upstream commit 28261da8a26f4915aa257d12d506c6ba179d961f ]
Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.
Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.
Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499
L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397
L2CAP: Connection Request (0x02) ident 27 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441
L2CAP: Connection Response (0x03) ident 27 len 8
Destination CID: 65
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073
L2CAP: Connection Request (0x02) ident 12 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371
L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804
L2CAP: Connection Response (0x03) ident 12 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Fix is to check that channel is in state BT_DISCONN before deleting the
channel.
This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/bluetooth/l2cap_core.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index ec9b5d159591..48d23abfe799 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -4374,6 +4374,12 @@ static inline int l2cap_disconnect_rsp(struct l2cap_conn *conn,
l2cap_chan_lock(chan);
+ if (chan->state != BT_DISCONN) {
+ l2cap_chan_unlock(chan);
+ mutex_unlock(&conn->chan_lock);
+ return 0;
+ }
+
l2cap_chan_hold(chan);
l2cap_chan_del(chan, 0);
--
2.20.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox