* Re: [PATCH v5 2/2] net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
From: Andrew Lunn @ 2019-09-16 11:57 UTC (permalink / raw)
To: Alexandru Ardelean
Cc: netdev, devicetree, linux-kernel, davem, robh+dt, mark.rutland,
f.fainelli, hkallweit1, mkubecek
In-Reply-To: <20190916073526.24711-3-alexandru.ardelean@analog.com>
On Mon, Sep 16, 2019 at 10:35:26AM +0300, Alexandru Ardelean wrote:
> This driver becomes the first user of the kernel's `ETHTOOL_PHY_EDPD`
> phy-tunable feature.
> EDPD is also enabled by default on PHY config_init, but can be disabled via
> the phy-tunable control.
>
> When enabling EDPD, it's also a good idea (for the ADIN PHYs) to enable TX
> periodic pulses, so that in case the other PHY is also on EDPD mode, there
> is no lock-up situation where both sides are waiting for the other to
> transmit.
>
> Via the phy-tunable control, TX pulses can be disabled if specifying 0
> `tx-interval` via ethtool.
>
> The ADIN PHY supports only fixed 1 second intervals; they cannot be
> configured. That is why the acceptable values are 1,
> ETHTOOL_PHY_EDPD_DFLT_TX_MSECS and ETHTOOL_PHY_EDPD_NO_TX (which disables
> TX pulses).
>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Andrew
^ permalink raw reply
* RE: [PATCH V1 net-next 01/11] net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
From: Kiyanovski, Arthur @ 2019-09-16 11:39 UTC (permalink / raw)
To: David Miller
Cc: netdev@vger.kernel.org, Woodhouse, David, Machulsky, Zorik,
Matushevsky, Alexander, Bshara, Saeed, Wilson, Matt,
Liguori, Anthony, Bshara, Nafea, Tzalik, Guy, Belgazal, Netanel,
Saidi, Ali, Herrenschmidt, Benjamin, Jubran, Samih, Dagan, Noam
In-Reply-To: <20190915.193241.878202512573492759.davem@davemloft.net>
> -----Original Message-----
> From: David Miller <davem@davemloft.net>
> Sent: Sunday, September 15, 2019 9:33 PM
> To: Kiyanovski, Arthur <akiyano@amazon.com>
> Cc: netdev@vger.kernel.org; Woodhouse, David <dwmw@amazon.co.uk>;
> Machulsky, Zorik <zorik@amazon.com>; Matushevsky, Alexander
> <matua@amazon.com>; Bshara, Saeed <saeedb@amazon.com>; Wilson, Matt
> <msw@amazon.com>; Liguori, Anthony <aliguori@amazon.com>; Bshara,
> Nafea <nafea@amazon.com>; Tzalik, Guy <gtzalik@amazon.com>; Belgazal,
> Netanel <netanel@amazon.com>; Saidi, Ali <alisaidi@amazon.com>;
> Herrenschmidt, Benjamin <benh@amazon.com>; Jubran, Samih
> <sameehj@amazon.com>; Dagan, Noam <ndagan@amazon.com>
> Subject: Re: [PATCH V1 net-next 01/11] net: ena: add intr_moder_rx_interval to
> struct ena_com_dev and use it
>
> From: <akiyano@amazon.com>
> Date: Fri, 13 Sep 2019 01:08:38 +0300
>
> > @@ -1307,8 +1304,8 @@ static void
> ena_com_update_intr_delay_resolution(struct ena_com_dev *ena_dev,
> > ena_dev->intr_delay_resolution = intr_delay_resolution;
> >
> > /* update Rx */
> > - for (i = 0; i < ENA_INTR_MAX_NUM_OF_LEVELS; i++)
> > - intr_moder_tbl[i].intr_moder_interval /= intr_delay_resolution;
> > + ena_dev->intr_moder_rx_interval /= intr_delay_resolution;
> > +
> >
> > /* update Tx */
>
> Now there are two empty lines here, please remove one of them.
Thanks.
For some reason checkpatch did not catch this and also another such extra space.
Sent out V2 of the patchset.
^ permalink raw reply
* [PATCH V2 net-next 10/11] net: ena: fix retrieval of nonadaptive interrupt moderation intervals
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Nonadaptive interrupt moderation intervals are assigned the value set
by the user in ethtool -C divided by ena_dev->intr_delay_resolution.
Therefore when the user tries to get the nonadaptive interrupt moderation
intervals with ethtool -c the code needs to multiply the saved value
by ena_dev->intr_delay_resolution.
The current code erroneously divides instead of multiplying in ethtool -c.
This patch fixes this.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_ethtool.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_ethtool.c b/drivers/net/ethernet/amazon/ena/ena_ethtool.c
index 0f90e2296630..16553d92fad2 100644
--- a/drivers/net/ethernet/amazon/ena/ena_ethtool.c
+++ b/drivers/net/ethernet/amazon/ena/ena_ethtool.c
@@ -310,14 +310,15 @@ static int ena_get_coalesce(struct net_device *net_dev,
/* the devie doesn't support interrupt moderation */
return -EOPNOTSUPP;
}
+
coalesce->tx_coalesce_usecs =
- ena_com_get_nonadaptive_moderation_interval_tx(ena_dev) /
+ ena_com_get_nonadaptive_moderation_interval_tx(ena_dev) *
ena_dev->intr_delay_resolution;
if (!ena_com_get_adaptive_moderation_enabled(ena_dev))
coalesce->rx_coalesce_usecs =
ena_com_get_nonadaptive_moderation_interval_rx(ena_dev)
- / ena_dev->intr_delay_resolution;
+ * ena_dev->intr_delay_resolution;
coalesce->use_adaptive_rx_coalesce =
ena_com_get_adaptive_moderation_enabled(ena_dev);
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 00/11] net: ena: implement adaptive interrupt moderation using dim
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
From: Arthur Kiyanovski <akiyano@amazon.com>
In this patchset we replace our adaptive interrupt moderation
implementation with the dim library implementation.
The dim library showed great improvement in throughput, latency
and CPU usage in different scenarios on ARM CPUs.
This patchset also includes a few bug fixes to the parts of the
old implementation of adaptive interrupt moderation that were left.
Changes from V1 patchset:
Removed stray empty lines from patches 01/11, 09/11.
Arthur Kiyanovski (11):
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: reimplement set/get_coalesce()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: remove code duplication in
ena_com_update_nonadaptive_moderation_interval _*()
net: ena: remove old adaptive interrupt moderation code from
ena_netdev
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove all old adaptive rx interrupt moderation code from
ena_com
net: ena: fix update of interrupt moderation register
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix incorrect update of intr_delay_resolution
.../net/ethernet/amazon/ena/ena_admin_defs.h | 8 +
drivers/net/ethernet/amazon/ena/ena_com.c | 175 ++++--------------
drivers/net/ethernet/amazon/ena/ena_com.h | 151 +--------------
drivers/net/ethernet/amazon/ena/ena_ethtool.c | 89 +++------
drivers/net/ethernet/amazon/ena/ena_netdev.c | 85 +++++----
drivers/net/ethernet/amazon/ena/ena_netdev.h | 8 +-
6 files changed, 128 insertions(+), 388 deletions(-)
--
2.17.2
^ permalink raw reply
* [PATCH V2 net-next 11/11] net: ena: fix incorrect update of intr_delay_resolution
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
ena_dev->intr_moder_rx/tx_interval save the intervals received from the
user after dividing them by ena_dev->intr_delay_resolution. Therefore
when intr_delay_resolution changes, the code needs to first mutiply
intr_moder_rx/tx_interval by the previous intr_delay_resolution to get
the value originally given by the user, and only then divide it by the
new intr_delay_resolution.
Current code does not first multiply intr_moder_rx/tx_interval by the old
intr_delay_resolution. This commit fixes it.
Also initialize ena_dev->intr_delay_resolution to be 1.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_com.c | 21 ++++++++++++++++----
drivers/net/ethernet/amazon/ena/ena_com.h | 1 +
drivers/net/ethernet/amazon/ena/ena_netdev.c | 1 +
3 files changed, 19 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c
index 621b747f062b..ea62604fdf8c 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.c
+++ b/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -1281,17 +1281,30 @@ static int ena_com_ind_tbl_convert_from_device(struct ena_com_dev *ena_dev)
static void ena_com_update_intr_delay_resolution(struct ena_com_dev *ena_dev,
u16 intr_delay_resolution)
{
+ /* Initial value of intr_delay_resolution might be 0 */
+ u16 prev_intr_delay_resolution =
+ ena_dev->intr_delay_resolution ?
+ ena_dev->intr_delay_resolution :
+ ENA_DEFAULT_INTR_DELAY_RESOLUTION;
+
if (!intr_delay_resolution) {
pr_err("Illegal intr_delay_resolution provided. Going to use default 1 usec resolution\n");
- intr_delay_resolution = 1;
+ intr_delay_resolution = ENA_DEFAULT_INTR_DELAY_RESOLUTION;
}
- ena_dev->intr_delay_resolution = intr_delay_resolution;
/* update Rx */
- ena_dev->intr_moder_rx_interval /= intr_delay_resolution;
+ ena_dev->intr_moder_rx_interval =
+ ena_dev->intr_moder_rx_interval *
+ prev_intr_delay_resolution /
+ intr_delay_resolution;
/* update Tx */
- ena_dev->intr_moder_tx_interval /= intr_delay_resolution;
+ ena_dev->intr_moder_tx_interval =
+ ena_dev->intr_moder_tx_interval *
+ prev_intr_delay_resolution /
+ intr_delay_resolution;
+
+ ena_dev->intr_delay_resolution = intr_delay_resolution;
}
/*****************************************************************************/
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.h b/drivers/net/ethernet/amazon/ena/ena_com.h
index ddc2a8c50333..7c941eba0bc9 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.h
+++ b/drivers/net/ethernet/amazon/ena/ena_com.h
@@ -74,6 +74,7 @@
#define ENA_INTR_INITIAL_TX_INTERVAL_USECS 196
#define ENA_INTR_INITIAL_RX_INTERVAL_USECS 0
+#define ENA_DEFAULT_INTR_DELAY_RESOLUTION 1
#define ENA_HW_HINTS_NO_TIMEOUT 0xFFFF
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index 54539e57aa73..e4bf7a4af87a 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -3500,6 +3500,7 @@ static int ena_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
*/
ena_dev->intr_moder_tx_interval = ENA_INTR_INITIAL_TX_INTERVAL_USECS;
ena_dev->intr_moder_rx_interval = ENA_INTR_INITIAL_RX_INTERVAL_USECS;
+ ena_dev->intr_delay_resolution = ENA_DEFAULT_INTR_DELAY_RESOLUTION;
io_queue_num = ena_calc_io_queue_num(pdev, ena_dev, &get_feat_ctx);
rc = ena_calc_queue_size(&calc_queue_ctx);
if (rc || io_queue_num <= 0) {
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 02/11] net: ena: switch to dim algorithm for rx adaptive interrupt moderation
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Use the dim library for the rx adaptive interrupt moderation implementation
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_com.c | 4 +-
drivers/net/ethernet/amazon/ena/ena_netdev.c | 55 +++++++++++++-------
drivers/net/ethernet/amazon/ena/ena_netdev.h | 3 ++
3 files changed, 41 insertions(+), 21 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c
index 4144936bf8a2..f3c67c27c19c 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.c
+++ b/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -2839,9 +2839,7 @@ int ena_com_init_interrupt_moderation(struct ena_com_dev *ena_dev)
delay_resolution = get_resp.u.intr_moderation.intr_delay_resolution;
ena_com_update_intr_delay_resolution(ena_dev, delay_resolution);
- /* Disable adaptive moderation by default - can be enabled from
- * ethtool
- */
+ /* Disable adaptive moderation by default - can be enabled later */
ena_com_disable_adaptive_moderation(ena_dev);
return 0;
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index 233b252ceb9e..cdcc169b87fa 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -196,6 +196,7 @@ static void ena_init_io_rings(struct ena_adapter *adapter)
rxr->smoothed_interval =
ena_com_get_nonadaptive_moderation_interval_rx(ena_dev);
rxr->empty_rx_queue = 0;
+ adapter->ena_napi[i].dim.mode = DIM_CQ_PERIOD_MODE_START_FROM_EQE;
}
}
@@ -712,6 +713,7 @@ static void ena_destroy_all_rx_queues(struct ena_adapter *adapter)
for (i = 0; i < adapter->num_queues; i++) {
ena_qid = ENA_IO_RXQ_IDX(i);
+ cancel_work_sync(&adapter->ena_napi[i].dim.work);
ena_com_destroy_io_queue(adapter->ena_dev, ena_qid);
}
}
@@ -1155,23 +1157,35 @@ static int ena_clean_rx_irq(struct ena_ring *rx_ring, struct napi_struct *napi,
return 0;
}
-void ena_adjust_intr_moderation(struct ena_ring *rx_ring,
- struct ena_ring *tx_ring)
+static void ena_dim_work(struct work_struct *w)
{
- /* We apply adaptive moderation on Rx path only.
- * Tx uses static interrupt moderation.
- */
- ena_com_calculate_interrupt_delay(rx_ring->ena_dev,
- rx_ring->per_napi_packets,
- rx_ring->per_napi_bytes,
- &rx_ring->smoothed_interval,
- &rx_ring->moder_tbl_idx);
-
- /* Reset per napi packets/bytes */
- tx_ring->per_napi_packets = 0;
- tx_ring->per_napi_bytes = 0;
+ struct dim *dim = container_of(w, struct dim, work);
+ struct dim_cq_moder cur_moder =
+ net_dim_get_rx_moderation(dim->mode, dim->profile_ix);
+ struct ena_napi *ena_napi = container_of(dim, struct ena_napi, dim);
+
+ ena_napi->rx_ring->smoothed_interval = cur_moder.usec;
+ dim->state = DIM_START_MEASURE;
+}
+
+static void ena_adjust_adaptive_rx_intr_moderation(struct ena_napi *ena_napi)
+{
+ struct dim_sample dim_sample;
+ struct ena_ring *rx_ring = ena_napi->rx_ring;
+
+ if (!rx_ring->per_napi_packets)
+ return;
+
+ rx_ring->non_empty_napi_events++;
+
+ dim_update_sample(rx_ring->non_empty_napi_events,
+ rx_ring->rx_stats.cnt,
+ rx_ring->rx_stats.bytes,
+ &dim_sample);
+
+ net_dim(&ena_napi->dim, dim_sample);
+
rx_ring->per_napi_packets = 0;
- rx_ring->per_napi_bytes = 0;
}
static void ena_unmask_interrupt(struct ena_ring *tx_ring,
@@ -1260,9 +1274,11 @@ static int ena_io_poll(struct napi_struct *napi, int budget)
* from the interrupt context (vs from sk_busy_loop)
*/
if (napi_complete_done(napi, rx_work_done)) {
- /* Tx and Rx share the same interrupt vector */
+ /* We apply adaptive moderation on Rx path only.
+ * Tx uses static interrupt moderation.
+ */
if (ena_com_get_adaptive_moderation_enabled(rx_ring->ena_dev))
- ena_adjust_intr_moderation(rx_ring, tx_ring);
+ ena_adjust_adaptive_rx_intr_moderation(ena_napi);
ena_unmask_interrupt(tx_ring, rx_ring);
}
@@ -1740,13 +1756,16 @@ static int ena_create_all_io_rx_queues(struct ena_adapter *adapter)
rc = ena_create_io_rx_queue(adapter, i);
if (rc)
goto create_err;
+ INIT_WORK(&adapter->ena_napi[i].dim.work, ena_dim_work);
}
return 0;
create_err:
- while (i--)
+ while (i--) {
+ cancel_work_sync(&adapter->ena_napi[i].dim.work);
ena_com_destroy_io_queue(ena_dev, ENA_IO_RXQ_IDX(i));
+ }
return rc;
}
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.h b/drivers/net/ethernet/amazon/ena/ena_netdev.h
index efbcffd22215..f67ecab3389a 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.h
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.h
@@ -34,6 +34,7 @@
#define ENA_H
#include <linux/bitops.h>
+#include <linux/dim.h>
#include <linux/etherdevice.h>
#include <linux/inetdevice.h>
#include <linux/interrupt.h>
@@ -153,6 +154,7 @@ struct ena_napi {
struct ena_ring *tx_ring;
struct ena_ring *rx_ring;
u32 qid;
+ struct dim dim;
};
struct ena_calc_queue_size_ctx {
@@ -280,6 +282,7 @@ struct ena_ring {
u32 per_napi_packets;
u32 per_napi_bytes;
enum ena_intr_moder_level moder_tbl_idx;
+ u16 non_empty_napi_events;
struct u64_stats_sync syncp;
union {
struct ena_stats_tx tx_stats;
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 08/11] net: ena: remove all old adaptive rx interrupt moderation code from ena_com
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Remove previous implementation of adaptive rx interrupt moderation
from ena_com files.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_com.c | 110 -----------------
drivers/net/ethernet/amazon/ena/ena_com.h | 142 ----------------------
2 files changed, 252 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c
index bbb59fd220a1..621b747f062b 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.c
+++ b/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -1278,22 +1278,6 @@ static int ena_com_ind_tbl_convert_from_device(struct ena_com_dev *ena_dev)
return 0;
}
-static int ena_com_init_interrupt_moderation_table(struct ena_com_dev *ena_dev)
-{
- size_t size;
-
- size = sizeof(struct ena_intr_moder_entry) * ENA_INTR_MAX_NUM_OF_LEVELS;
-
- ena_dev->intr_moder_tbl =
- devm_kzalloc(ena_dev->dmadev, size, GFP_KERNEL);
- if (!ena_dev->intr_moder_tbl)
- return -ENOMEM;
-
- ena_com_config_default_interrupt_moderation_table(ena_dev);
-
- return 0;
-}
-
static void ena_com_update_intr_delay_resolution(struct ena_com_dev *ena_dev,
u16 intr_delay_resolution)
{
@@ -2802,13 +2786,6 @@ int ena_com_update_nonadaptive_moderation_interval_rx(struct ena_com_dev *ena_de
&ena_dev->intr_moder_rx_interval);
}
-void ena_com_destroy_interrupt_moderation(struct ena_com_dev *ena_dev)
-{
- if (ena_dev->intr_moder_tbl)
- devm_kfree(ena_dev->dmadev, ena_dev->intr_moder_tbl);
- ena_dev->intr_moder_tbl = NULL;
-}
-
int ena_com_init_interrupt_moderation(struct ena_com_dev *ena_dev)
{
struct ena_admin_get_feat_resp get_resp;
@@ -2833,10 +2810,6 @@ int ena_com_init_interrupt_moderation(struct ena_com_dev *ena_dev)
return rc;
}
- rc = ena_com_init_interrupt_moderation_table(ena_dev);
- if (rc)
- goto err;
-
/* if moderation is supported by device we set adaptive moderation */
delay_resolution = get_resp.u.intr_moderation.intr_delay_resolution;
ena_com_update_intr_delay_resolution(ena_dev, delay_resolution);
@@ -2845,52 +2818,6 @@ int ena_com_init_interrupt_moderation(struct ena_com_dev *ena_dev)
ena_com_disable_adaptive_moderation(ena_dev);
return 0;
-err:
- ena_com_destroy_interrupt_moderation(ena_dev);
- return rc;
-}
-
-void ena_com_config_default_interrupt_moderation_table(struct ena_com_dev *ena_dev)
-{
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
-
- if (!intr_moder_tbl)
- return;
-
- intr_moder_tbl[ENA_INTR_MODER_LOWEST].intr_moder_interval =
- ENA_INTR_LOWEST_USECS;
- intr_moder_tbl[ENA_INTR_MODER_LOWEST].pkts_per_interval =
- ENA_INTR_LOWEST_PKTS;
- intr_moder_tbl[ENA_INTR_MODER_LOWEST].bytes_per_interval =
- ENA_INTR_LOWEST_BYTES;
-
- intr_moder_tbl[ENA_INTR_MODER_LOW].intr_moder_interval =
- ENA_INTR_LOW_USECS;
- intr_moder_tbl[ENA_INTR_MODER_LOW].pkts_per_interval =
- ENA_INTR_LOW_PKTS;
- intr_moder_tbl[ENA_INTR_MODER_LOW].bytes_per_interval =
- ENA_INTR_LOW_BYTES;
-
- intr_moder_tbl[ENA_INTR_MODER_MID].intr_moder_interval =
- ENA_INTR_MID_USECS;
- intr_moder_tbl[ENA_INTR_MODER_MID].pkts_per_interval =
- ENA_INTR_MID_PKTS;
- intr_moder_tbl[ENA_INTR_MODER_MID].bytes_per_interval =
- ENA_INTR_MID_BYTES;
-
- intr_moder_tbl[ENA_INTR_MODER_HIGH].intr_moder_interval =
- ENA_INTR_HIGH_USECS;
- intr_moder_tbl[ENA_INTR_MODER_HIGH].pkts_per_interval =
- ENA_INTR_HIGH_PKTS;
- intr_moder_tbl[ENA_INTR_MODER_HIGH].bytes_per_interval =
- ENA_INTR_HIGH_BYTES;
-
- intr_moder_tbl[ENA_INTR_MODER_HIGHEST].intr_moder_interval =
- ENA_INTR_HIGHEST_USECS;
- intr_moder_tbl[ENA_INTR_MODER_HIGHEST].pkts_per_interval =
- ENA_INTR_HIGHEST_PKTS;
- intr_moder_tbl[ENA_INTR_MODER_HIGHEST].bytes_per_interval =
- ENA_INTR_HIGHEST_BYTES;
}
unsigned int ena_com_get_nonadaptive_moderation_interval_tx(struct ena_com_dev *ena_dev)
@@ -2903,43 +2830,6 @@ unsigned int ena_com_get_nonadaptive_moderation_interval_rx(struct ena_com_dev *
return ena_dev->intr_moder_rx_interval;
}
-void ena_com_init_intr_moderation_entry(struct ena_com_dev *ena_dev,
- enum ena_intr_moder_level level,
- struct ena_intr_moder_entry *entry)
-{
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
-
- if (level >= ENA_INTR_MAX_NUM_OF_LEVELS)
- return;
-
- intr_moder_tbl[level].intr_moder_interval = entry->intr_moder_interval;
- if (ena_dev->intr_delay_resolution)
- intr_moder_tbl[level].intr_moder_interval /=
- ena_dev->intr_delay_resolution;
- intr_moder_tbl[level].pkts_per_interval = entry->pkts_per_interval;
-
- /* use hardcoded value until ethtool supports bytecount parameter */
- if (entry->bytes_per_interval != ENA_INTR_BYTE_COUNT_NOT_SUPPORTED)
- intr_moder_tbl[level].bytes_per_interval = entry->bytes_per_interval;
-}
-
-void ena_com_get_intr_moderation_entry(struct ena_com_dev *ena_dev,
- enum ena_intr_moder_level level,
- struct ena_intr_moder_entry *entry)
-{
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
-
- if (level >= ENA_INTR_MAX_NUM_OF_LEVELS)
- return;
-
- entry->intr_moder_interval = intr_moder_tbl[level].intr_moder_interval;
- if (ena_dev->intr_delay_resolution)
- entry->intr_moder_interval *= ena_dev->intr_delay_resolution;
- entry->pkts_per_interval =
- intr_moder_tbl[level].pkts_per_interval;
- entry->bytes_per_interval = intr_moder_tbl[level].bytes_per_interval;
-}
-
int ena_com_config_dev_mode(struct ena_com_dev *ena_dev,
struct ena_admin_feature_llq_desc *llq_features,
struct ena_llq_configurations *llq_default_cfg)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.h b/drivers/net/ethernet/amazon/ena/ena_com.h
index baeefc6af4f3..ddc2a8c50333 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.h
+++ b/drivers/net/ethernet/amazon/ena/ena_com.h
@@ -72,46 +72,13 @@
/*****************************************************************************/
/* ENA adaptive interrupt moderation settings */
-#define ENA_INTR_LOWEST_USECS (0)
-#define ENA_INTR_LOWEST_PKTS (3)
-#define ENA_INTR_LOWEST_BYTES (2 * 1524)
-
-#define ENA_INTR_LOW_USECS (32)
-#define ENA_INTR_LOW_PKTS (12)
-#define ENA_INTR_LOW_BYTES (16 * 1024)
-
-#define ENA_INTR_MID_USECS (80)
-#define ENA_INTR_MID_PKTS (48)
-#define ENA_INTR_MID_BYTES (64 * 1024)
-
-#define ENA_INTR_HIGH_USECS (128)
-#define ENA_INTR_HIGH_PKTS (96)
-#define ENA_INTR_HIGH_BYTES (128 * 1024)
-
-#define ENA_INTR_HIGHEST_USECS (192)
-#define ENA_INTR_HIGHEST_PKTS (128)
-#define ENA_INTR_HIGHEST_BYTES (192 * 1024)
-
#define ENA_INTR_INITIAL_TX_INTERVAL_USECS 196
#define ENA_INTR_INITIAL_RX_INTERVAL_USECS 0
-#define ENA_INTR_DELAY_OLD_VALUE_WEIGHT 6
-#define ENA_INTR_DELAY_NEW_VALUE_WEIGHT 4
-#define ENA_INTR_MODER_LEVEL_STRIDE 2
-#define ENA_INTR_BYTE_COUNT_NOT_SUPPORTED 0xFFFFFF
#define ENA_HW_HINTS_NO_TIMEOUT 0xFFFF
#define ENA_FEATURE_MAX_QUEUE_EXT_VER 1
-enum ena_intr_moder_level {
- ENA_INTR_MODER_LOWEST = 0,
- ENA_INTR_MODER_LOW,
- ENA_INTR_MODER_MID,
- ENA_INTR_MODER_HIGH,
- ENA_INTR_MODER_HIGHEST,
- ENA_INTR_MAX_NUM_OF_LEVELS,
-};
-
struct ena_llq_configurations {
enum ena_admin_llq_header_location llq_header_location;
enum ena_admin_llq_ring_entry_size llq_ring_entry_size;
@@ -120,12 +87,6 @@ struct ena_llq_configurations {
u16 llq_ring_entry_size_value;
};
-struct ena_intr_moder_entry {
- unsigned int intr_moder_interval;
- unsigned int pkts_per_interval;
- unsigned int bytes_per_interval;
-};
-
enum queue_direction {
ENA_COM_IO_QUEUE_DIRECTION_TX,
ENA_COM_IO_QUEUE_DIRECTION_RX
@@ -920,11 +881,6 @@ int ena_com_execute_admin_command(struct ena_com_admin_queue *admin_queue,
*/
int ena_com_init_interrupt_moderation(struct ena_com_dev *ena_dev);
-/* ena_com_destroy_interrupt_moderation - Destroy interrupt moderation resources
- * @ena_dev: ENA communication layer struct
- */
-void ena_com_destroy_interrupt_moderation(struct ena_com_dev *ena_dev);
-
/* ena_com_interrupt_moderation_supported - Return if interrupt moderation
* capability is supported by the device.
*
@@ -932,12 +888,6 @@ void ena_com_destroy_interrupt_moderation(struct ena_com_dev *ena_dev);
*/
bool ena_com_interrupt_moderation_supported(struct ena_com_dev *ena_dev);
-/* ena_com_config_default_interrupt_moderation_table - Restore the interrupt
- * moderation table back to the default parameters.
- * @ena_dev: ENA communication layer struct
- */
-void ena_com_config_default_interrupt_moderation_table(struct ena_com_dev *ena_dev);
-
/* ena_com_update_nonadaptive_moderation_interval_tx - Update the
* non-adaptive interval in Tx direction.
* @ena_dev: ENA communication layer struct
@@ -974,29 +924,6 @@ unsigned int ena_com_get_nonadaptive_moderation_interval_tx(struct ena_com_dev *
*/
unsigned int ena_com_get_nonadaptive_moderation_interval_rx(struct ena_com_dev *ena_dev);
-/* ena_com_init_intr_moderation_entry - Update a single entry in the interrupt
- * moderation table.
- * @ena_dev: ENA communication layer struct
- * @level: Interrupt moderation table level
- * @entry: Entry value
- *
- * Update a single entry in the interrupt moderation table.
- */
-void ena_com_init_intr_moderation_entry(struct ena_com_dev *ena_dev,
- enum ena_intr_moder_level level,
- struct ena_intr_moder_entry *entry);
-
-/* ena_com_get_intr_moderation_entry - Init ena_intr_moder_entry.
- * @ena_dev: ENA communication layer struct
- * @level: Interrupt moderation table level
- * @entry: Entry to fill.
- *
- * Initialize the entry according to the adaptive interrupt moderation table.
- */
-void ena_com_get_intr_moderation_entry(struct ena_com_dev *ena_dev,
- enum ena_intr_moder_level level,
- struct ena_intr_moder_entry *entry);
-
/* ena_com_config_dev_mode - Configure the placement policy of the device.
* @ena_dev: ENA communication layer struct
* @llq_features: LLQ feature descriptor, retrieve via
@@ -1022,75 +949,6 @@ static inline void ena_com_disable_adaptive_moderation(struct ena_com_dev *ena_d
ena_dev->adaptive_coalescing = false;
}
-/* ena_com_calculate_interrupt_delay - Calculate new interrupt delay
- * @ena_dev: ENA communication layer struct
- * @pkts: Number of packets since the last update
- * @bytes: Number of bytes received since the last update.
- * @smoothed_interval: Returned interval
- * @moder_tbl_idx: Current table level as input update new level as return
- * value.
- */
-static inline void ena_com_calculate_interrupt_delay(struct ena_com_dev *ena_dev,
- unsigned int pkts,
- unsigned int bytes,
- unsigned int *smoothed_interval,
- unsigned int *moder_tbl_idx)
-{
- enum ena_intr_moder_level curr_moder_idx, new_moder_idx;
- struct ena_intr_moder_entry *curr_moder_entry;
- struct ena_intr_moder_entry *pred_moder_entry;
- struct ena_intr_moder_entry *new_moder_entry;
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
- unsigned int interval;
-
- /* We apply adaptive moderation on Rx path only.
- * Tx uses static interrupt moderation.
- */
- if (!pkts || !bytes)
- /* Tx interrupt, or spurious interrupt,
- * in both cases we just use same delay values
- */
- return;
-
- curr_moder_idx = (enum ena_intr_moder_level)(*moder_tbl_idx);
- if (unlikely(curr_moder_idx >= ENA_INTR_MAX_NUM_OF_LEVELS)) {
- pr_err("Wrong moderation index %u\n", curr_moder_idx);
- return;
- }
-
- curr_moder_entry = &intr_moder_tbl[curr_moder_idx];
- new_moder_idx = curr_moder_idx;
-
- if (curr_moder_idx == ENA_INTR_MODER_LOWEST) {
- if ((pkts > curr_moder_entry->pkts_per_interval) ||
- (bytes > curr_moder_entry->bytes_per_interval))
- new_moder_idx =
- (enum ena_intr_moder_level)(curr_moder_idx + ENA_INTR_MODER_LEVEL_STRIDE);
- } else {
- pred_moder_entry = &intr_moder_tbl[curr_moder_idx - ENA_INTR_MODER_LEVEL_STRIDE];
-
- if ((pkts <= pred_moder_entry->pkts_per_interval) ||
- (bytes <= pred_moder_entry->bytes_per_interval))
- new_moder_idx =
- (enum ena_intr_moder_level)(curr_moder_idx - ENA_INTR_MODER_LEVEL_STRIDE);
- else if ((pkts > curr_moder_entry->pkts_per_interval) ||
- (bytes > curr_moder_entry->bytes_per_interval)) {
- if (curr_moder_idx != ENA_INTR_MODER_HIGHEST)
- new_moder_idx =
- (enum ena_intr_moder_level)(curr_moder_idx + ENA_INTR_MODER_LEVEL_STRIDE);
- }
- }
- new_moder_entry = &intr_moder_tbl[new_moder_idx];
-
- interval = new_moder_entry->intr_moder_interval;
- *smoothed_interval = (
- (interval * ENA_INTR_DELAY_NEW_VALUE_WEIGHT +
- ENA_INTR_DELAY_OLD_VALUE_WEIGHT * (*smoothed_interval)) + 5) /
- 10;
-
- *moder_tbl_idx = new_moder_idx;
-}
-
/* ena_com_update_intr_reg - Prepare interrupt register
* @intr_reg: interrupt register to update.
* @rx_delay_interval: Rx interval in usecs
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 09/11] net: ena: fix update of interrupt moderation register
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Current implementation always updates the interrupt register with
the smoothed_interval of the rx_ring. However this should be
done only in case of adaptive interrupt moderation. If non-adaptive
interrupt moderation is used, the non-adaptive interrupt moderation
interval should be used. This commit fixes that.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_netdev.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index 8b9f8b90e525..54539e57aa73 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -1187,12 +1187,15 @@ static void ena_unmask_interrupt(struct ena_ring *tx_ring,
struct ena_ring *rx_ring)
{
struct ena_eth_io_intr_reg intr_reg;
+ u32 rx_interval = ena_com_get_adaptive_moderation_enabled(rx_ring->ena_dev) ?
+ rx_ring->smoothed_interval :
+ ena_com_get_nonadaptive_moderation_interval_rx(rx_ring->ena_dev);
/* Update intr register: rx intr delay,
* tx intr delay and interrupt unmask
*/
ena_com_update_intr_reg(&intr_reg,
- rx_ring->smoothed_interval,
+ rx_interval,
tx_ring->smoothed_interval,
true);
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 07/11] net: ena: remove ena_restore_ethtool_params() and relevant fields
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Deleted unused 4 fields from struct ena_adapter and their only user
ena_restore_ethtool_params().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_netdev.c | 10 ----------
drivers/net/ethernet/amazon/ena/ena_netdev.h | 3 ---
2 files changed, 13 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index 1d8855ab8624..8b9f8b90e525 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -1563,14 +1563,6 @@ static void ena_napi_enable_all(struct ena_adapter *adapter)
napi_enable(&adapter->ena_napi[i].napi);
}
-static void ena_restore_ethtool_params(struct ena_adapter *adapter)
-{
- adapter->tx_usecs = 0;
- adapter->rx_usecs = 0;
- adapter->tx_frames = 1;
- adapter->rx_frames = 1;
-}
-
/* Configure the Rx forwarding */
static int ena_rss_configure(struct ena_adapter *adapter)
{
@@ -1620,8 +1612,6 @@ static int ena_up_complete(struct ena_adapter *adapter)
/* enable transmits */
netif_tx_start_all_queues(adapter->netdev);
- ena_restore_ethtool_params(adapter);
-
ena_napi_enable_all(adapter);
return 0;
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.h b/drivers/net/ethernet/amazon/ena/ena_netdev.h
index e9450991ab74..72ee51a82ec7 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.h
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.h
@@ -330,9 +330,6 @@ struct ena_adapter {
u32 missing_tx_completion_threshold;
- u32 tx_usecs, rx_usecs; /* interrupt moderation */
- u32 tx_frames, rx_frames; /* interrupt moderation */
-
u32 requested_tx_ring_size;
u32 requested_rx_ring_size;
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 06/11] net: ena: remove old adaptive interrupt moderation code from ena_netdev
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
1. Out of the fields {per_napi_bytes, per_napi_packets} in struct ena_ring,
only rx_ring->per_napi_packets are used to determine if napi did work
for dim.
This commit removes all other uses of these fields.
2. Remove ena_ring->moder_tbl_idx, which is not used by dim.
3. Remove all calls to ena_com_destroy_interrupt_moderation(), since all it
did was to destroy the interrupt moderation table, which is removed as
part of removing old interrupt moderation code.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_netdev.c | 8 --------
drivers/net/ethernet/amazon/ena/ena_netdev.h | 2 --
2 files changed, 10 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index f19736493c01..1d8855ab8624 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -158,7 +158,6 @@ static void ena_init_io_rings_common(struct ena_adapter *adapter,
ring->adapter = adapter;
ring->ena_dev = adapter->ena_dev;
ring->per_napi_packets = 0;
- ring->per_napi_bytes = 0;
ring->cpu = 0;
ring->first_interrupt = false;
ring->no_interrupt_event_cnt = 0;
@@ -834,9 +833,6 @@ static int ena_clean_tx_irq(struct ena_ring *tx_ring, u32 budget)
__netif_tx_unlock(txq);
}
- tx_ring->per_napi_bytes += tx_bytes;
- tx_ring->per_napi_packets += tx_pkts;
-
return tx_pkts;
}
@@ -1120,7 +1116,6 @@ static int ena_clean_rx_irq(struct ena_ring *rx_ring, struct napi_struct *napi,
} while (likely(res_budget));
work_done = budget - res_budget;
- rx_ring->per_napi_bytes += total_len;
rx_ring->per_napi_packets += work_done;
u64_stats_update_begin(&rx_ring->syncp);
rx_ring->rx_stats.bytes += total_len;
@@ -3641,7 +3636,6 @@ static int ena_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
ena_free_mgmnt_irq(adapter);
ena_disable_msix(adapter);
err_worker_destroy:
- ena_com_destroy_interrupt_moderation(ena_dev);
del_timer(&adapter->timer_service);
err_netdev_destroy:
free_netdev(netdev);
@@ -3702,8 +3696,6 @@ static void ena_remove(struct pci_dev *pdev)
pci_disable_device(pdev);
- ena_com_destroy_interrupt_moderation(ena_dev);
-
vfree(ena_dev);
}
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.h b/drivers/net/ethernet/amazon/ena/ena_netdev.h
index f67ecab3389a..e9450991ab74 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.h
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.h
@@ -280,8 +280,6 @@ struct ena_ring {
struct ena_com_rx_buf_info ena_bufs[ENA_PKT_MAX_BUFS];
u32 smoothed_interval;
u32 per_napi_packets;
- u32 per_napi_bytes;
- enum ena_intr_moder_level moder_tbl_idx;
u16 non_empty_napi_events;
struct u64_stats_sync syncp;
union {
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 05/11] net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Remove code duplication in:
ena_com_update_nonadaptive_moderation_interval_tx()
ena_com_update_nonadaptive_moderation_interval_rx()
functions.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_com.c | 30 ++++++++++++-----------
1 file changed, 16 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c
index f3c67c27c19c..bbb59fd220a1 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.c
+++ b/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -2772,32 +2772,34 @@ bool ena_com_interrupt_moderation_supported(struct ena_com_dev *ena_dev)
ENA_ADMIN_INTERRUPT_MODERATION);
}
-int ena_com_update_nonadaptive_moderation_interval_tx(struct ena_com_dev *ena_dev,
- u32 tx_coalesce_usecs)
+static int ena_com_update_nonadaptive_moderation_interval(u32 coalesce_usecs,
+ u32 intr_delay_resolution,
+ u32 *intr_moder_interval)
{
- if (!ena_dev->intr_delay_resolution) {
+ if (!intr_delay_resolution) {
pr_err("Illegal interrupt delay granularity value\n");
return -EFAULT;
}
- ena_dev->intr_moder_tx_interval = tx_coalesce_usecs /
- ena_dev->intr_delay_resolution;
+ *intr_moder_interval = coalesce_usecs / intr_delay_resolution;
return 0;
}
+int ena_com_update_nonadaptive_moderation_interval_tx(struct ena_com_dev *ena_dev,
+ u32 tx_coalesce_usecs)
+{
+ return ena_com_update_nonadaptive_moderation_interval(tx_coalesce_usecs,
+ ena_dev->intr_delay_resolution,
+ &ena_dev->intr_moder_tx_interval);
+}
+
int ena_com_update_nonadaptive_moderation_interval_rx(struct ena_com_dev *ena_dev,
u32 rx_coalesce_usecs)
{
- if (!ena_dev->intr_delay_resolution) {
- pr_err("Illegal interrupt delay granularity value\n");
- return -EFAULT;
- }
-
- ena_dev->intr_moder_rx_interval = rx_coalesce_usecs /
- ena_dev->intr_delay_resolution;
-
- return 0;
+ return ena_com_update_nonadaptive_moderation_interval(rx_coalesce_usecs,
+ ena_dev->intr_delay_resolution,
+ &ena_dev->intr_moder_rx_interval);
}
void ena_com_destroy_interrupt_moderation(struct ena_com_dev *ena_dev)
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 04/11] net: ena: enable the interrupt_moderation in driver_supported_features
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Add driver_supported_features to host_host info which is a new API used to
communicate to the device which features are supported by the driver.
Add the interrupt_moderation bit to host_info->driver_supported_features
and enable it to signal the device that this driver supports interrupt
moderation properly.
Reserved bits are for features implemented in the future
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_admin_defs.h | 8 ++++++++
drivers/net/ethernet/amazon/ena/ena_netdev.c | 3 +++
2 files changed, 11 insertions(+)
diff --git a/drivers/net/ethernet/amazon/ena/ena_admin_defs.h b/drivers/net/ethernet/amazon/ena/ena_admin_defs.h
index d19f2ecf8e84..8baf847e8622 100644
--- a/drivers/net/ethernet/amazon/ena/ena_admin_defs.h
+++ b/drivers/net/ethernet/amazon/ena/ena_admin_defs.h
@@ -808,6 +808,12 @@ struct ena_admin_host_info {
u16 num_cpus;
u16 reserved;
+
+ /* 1 :0 : reserved
+ * 2 : interrupt_moderation
+ * 31:3 : reserved
+ */
+ u32 driver_supported_features;
};
struct ena_admin_rss_ind_table_entry {
@@ -1110,6 +1116,8 @@ struct ena_admin_ena_mmio_req_read_less_resp {
#define ENA_ADMIN_HOST_INFO_DEVICE_MASK GENMASK(7, 3)
#define ENA_ADMIN_HOST_INFO_BUS_SHIFT 8
#define ENA_ADMIN_HOST_INFO_BUS_MASK GENMASK(15, 8)
+#define ENA_ADMIN_HOST_INFO_INTERRUPT_MODERATION_SHIFT 2
+#define ENA_ADMIN_HOST_INFO_INTERRUPT_MODERATION_MASK BIT(2)
/* aenq_common_desc */
#define ENA_ADMIN_AENQ_COMMON_DESC_PHASE_MASK BIT(0)
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index cdcc169b87fa..f19736493c01 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -2438,6 +2438,9 @@ static void ena_config_host_info(struct ena_com_dev *ena_dev,
("K"[0] << ENA_ADMIN_HOST_INFO_MODULE_TYPE_SHIFT);
host_info->num_cpus = num_online_cpus();
+ host_info->driver_supported_features =
+ ENA_ADMIN_HOST_INFO_INTERRUPT_MODERATION_MASK;
+
rc = ena_com_set_host_attributes(ena_dev);
if (rc) {
if (rc == -EOPNOTSUPP)
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 03/11] net: ena: reimplement set/get_coalesce()
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
1. Remove old adaptive interrupt moderation code from set/get_coalesce()
2. Add ena_update_rx_rings_intr_moderation() function for updating
nonadaptive interrupt moderation intervals similarly to
ena_update_tx_rings_intr_moderation().
3. Remove checks of multiple unsupported received interrupt coalescing
parameters. This makes code cleaner and cancels the need to update
it every time a new coalescing parameter is invented.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_ethtool.c | 84 ++++++-------------
1 file changed, 26 insertions(+), 58 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_ethtool.c b/drivers/net/ethernet/amazon/ena/ena_ethtool.c
index b997c3ce9e2b..0f90e2296630 100644
--- a/drivers/net/ethernet/amazon/ena/ena_ethtool.c
+++ b/drivers/net/ethernet/amazon/ena/ena_ethtool.c
@@ -305,7 +305,6 @@ static int ena_get_coalesce(struct net_device *net_dev,
{
struct ena_adapter *adapter = netdev_priv(net_dev);
struct ena_com_dev *ena_dev = adapter->ena_dev;
- struct ena_intr_moder_entry intr_moder_entry;
if (!ena_com_interrupt_moderation_supported(ena_dev)) {
/* the devie doesn't support interrupt moderation */
@@ -314,23 +313,12 @@ static int ena_get_coalesce(struct net_device *net_dev,
coalesce->tx_coalesce_usecs =
ena_com_get_nonadaptive_moderation_interval_tx(ena_dev) /
ena_dev->intr_delay_resolution;
- if (!ena_com_get_adaptive_moderation_enabled(ena_dev)) {
+
+ if (!ena_com_get_adaptive_moderation_enabled(ena_dev))
coalesce->rx_coalesce_usecs =
ena_com_get_nonadaptive_moderation_interval_rx(ena_dev)
/ ena_dev->intr_delay_resolution;
- } else {
- ena_com_get_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_LOWEST, &intr_moder_entry);
- coalesce->rx_coalesce_usecs_low = intr_moder_entry.intr_moder_interval;
- coalesce->rx_max_coalesced_frames_low = intr_moder_entry.pkts_per_interval;
-
- ena_com_get_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_MID, &intr_moder_entry);
- coalesce->rx_coalesce_usecs = intr_moder_entry.intr_moder_interval;
- coalesce->rx_max_coalesced_frames = intr_moder_entry.pkts_per_interval;
-
- ena_com_get_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_HIGHEST, &intr_moder_entry);
- coalesce->rx_coalesce_usecs_high = intr_moder_entry.intr_moder_interval;
- coalesce->rx_max_coalesced_frames_high = intr_moder_entry.pkts_per_interval;
- }
+
coalesce->use_adaptive_rx_coalesce =
ena_com_get_adaptive_moderation_enabled(ena_dev);
@@ -348,12 +336,22 @@ static void ena_update_tx_rings_intr_moderation(struct ena_adapter *adapter)
adapter->tx_ring[i].smoothed_interval = val;
}
+static void ena_update_rx_rings_intr_moderation(struct ena_adapter *adapter)
+{
+ unsigned int val;
+ int i;
+
+ val = ena_com_get_nonadaptive_moderation_interval_rx(adapter->ena_dev);
+
+ for (i = 0; i < adapter->num_queues; i++)
+ adapter->rx_ring[i].smoothed_interval = val;
+}
+
static int ena_set_coalesce(struct net_device *net_dev,
struct ethtool_coalesce *coalesce)
{
struct ena_adapter *adapter = netdev_priv(net_dev);
struct ena_com_dev *ena_dev = adapter->ena_dev;
- struct ena_intr_moder_entry intr_moder_entry;
int rc;
if (!ena_com_interrupt_moderation_supported(ena_dev)) {
@@ -361,22 +359,6 @@ static int ena_set_coalesce(struct net_device *net_dev,
return -EOPNOTSUPP;
}
- if (coalesce->rx_coalesce_usecs_irq ||
- coalesce->rx_max_coalesced_frames_irq ||
- coalesce->tx_coalesce_usecs_irq ||
- coalesce->tx_max_coalesced_frames ||
- coalesce->tx_max_coalesced_frames_irq ||
- coalesce->stats_block_coalesce_usecs ||
- coalesce->use_adaptive_tx_coalesce ||
- coalesce->pkt_rate_low ||
- coalesce->tx_coalesce_usecs_low ||
- coalesce->tx_max_coalesced_frames_low ||
- coalesce->pkt_rate_high ||
- coalesce->tx_coalesce_usecs_high ||
- coalesce->tx_max_coalesced_frames_high ||
- coalesce->rate_sample_interval)
- return -EINVAL;
-
rc = ena_com_update_nonadaptive_moderation_interval_tx(ena_dev,
coalesce->tx_coalesce_usecs);
if (rc)
@@ -384,37 +366,23 @@ static int ena_set_coalesce(struct net_device *net_dev,
ena_update_tx_rings_intr_moderation(adapter);
- if (ena_com_get_adaptive_moderation_enabled(ena_dev)) {
- if (!coalesce->use_adaptive_rx_coalesce) {
- ena_com_disable_adaptive_moderation(ena_dev);
- rc = ena_com_update_nonadaptive_moderation_interval_rx(ena_dev,
- coalesce->rx_coalesce_usecs);
- return rc;
- }
- } else { /* was in non-adaptive mode */
- if (coalesce->use_adaptive_rx_coalesce) {
+ if (coalesce->use_adaptive_rx_coalesce) {
+ if (!ena_com_get_adaptive_moderation_enabled(ena_dev))
ena_com_enable_adaptive_moderation(ena_dev);
- } else {
- rc = ena_com_update_nonadaptive_moderation_interval_rx(ena_dev,
- coalesce->rx_coalesce_usecs);
- return rc;
- }
+ return 0;
}
- intr_moder_entry.intr_moder_interval = coalesce->rx_coalesce_usecs_low;
- intr_moder_entry.pkts_per_interval = coalesce->rx_max_coalesced_frames_low;
- intr_moder_entry.bytes_per_interval = ENA_INTR_BYTE_COUNT_NOT_SUPPORTED;
- ena_com_init_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_LOWEST, &intr_moder_entry);
+ rc = ena_com_update_nonadaptive_moderation_interval_rx(ena_dev,
+ coalesce->rx_coalesce_usecs);
+ if (rc)
+ return rc;
- intr_moder_entry.intr_moder_interval = coalesce->rx_coalesce_usecs;
- intr_moder_entry.pkts_per_interval = coalesce->rx_max_coalesced_frames;
- intr_moder_entry.bytes_per_interval = ENA_INTR_BYTE_COUNT_NOT_SUPPORTED;
- ena_com_init_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_MID, &intr_moder_entry);
+ ena_update_rx_rings_intr_moderation(adapter);
- intr_moder_entry.intr_moder_interval = coalesce->rx_coalesce_usecs_high;
- intr_moder_entry.pkts_per_interval = coalesce->rx_max_coalesced_frames_high;
- intr_moder_entry.bytes_per_interval = ENA_INTR_BYTE_COUNT_NOT_SUPPORTED;
- ena_com_init_intr_moderation_entry(adapter->ena_dev, ENA_INTR_MODER_HIGHEST, &intr_moder_entry);
+ if (!coalesce->use_adaptive_rx_coalesce) {
+ if (ena_com_get_adaptive_moderation_enabled(ena_dev))
+ ena_com_disable_adaptive_moderation(ena_dev);
+ }
return 0;
}
--
2.17.2
^ permalink raw reply related
* [PATCH V2 net-next 01/11] net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
From: akiyano @ 2019-09-16 11:31 UTC (permalink / raw)
To: davem, netdev
Cc: Arthur Kiyanovski, dwmw, zorik, matua, saeedb, msw, aliguori,
nafea, gtzalik, netanel, alisaidi, benh, sameehj, ndagan
In-Reply-To: <1568633496-4143-1-git-send-email-akiyano@amazon.com>
From: Arthur Kiyanovski <akiyano@amazon.com>
Add intr_moder_rx_interval to struct ena_com_dev and use it as the
location where the interrupt moderation rx interval is saved, instead
of the interrupt moderation table.
This is done as a first step before removing the old interrupt moderation
code.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
---
drivers/net/ethernet/amazon/ena/ena_com.c | 20 ++++----------------
drivers/net/ethernet/amazon/ena/ena_com.h | 8 +++++++-
drivers/net/ethernet/amazon/ena/ena_netdev.c | 3 ++-
3 files changed, 13 insertions(+), 18 deletions(-)
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c
index 911a2e7a375a..4144936bf8a2 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.c
+++ b/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -1297,9 +1297,6 @@ static int ena_com_init_interrupt_moderation_table(struct ena_com_dev *ena_dev)
static void ena_com_update_intr_delay_resolution(struct ena_com_dev *ena_dev,
u16 intr_delay_resolution)
{
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
- unsigned int i;
-
if (!intr_delay_resolution) {
pr_err("Illegal intr_delay_resolution provided. Going to use default 1 usec resolution\n");
intr_delay_resolution = 1;
@@ -1307,8 +1304,7 @@ static void ena_com_update_intr_delay_resolution(struct ena_com_dev *ena_dev,
ena_dev->intr_delay_resolution = intr_delay_resolution;
/* update Rx */
- for (i = 0; i < ENA_INTR_MAX_NUM_OF_LEVELS; i++)
- intr_moder_tbl[i].intr_moder_interval /= intr_delay_resolution;
+ ena_dev->intr_moder_rx_interval /= intr_delay_resolution;
/* update Tx */
ena_dev->intr_moder_tx_interval /= intr_delay_resolution;
@@ -2798,11 +2794,8 @@ int ena_com_update_nonadaptive_moderation_interval_rx(struct ena_com_dev *ena_de
return -EFAULT;
}
- /* We use LOWEST entry of moderation table for storing
- * nonadaptive interrupt coalescing values
- */
- ena_dev->intr_moder_tbl[ENA_INTR_MODER_LOWEST].intr_moder_interval =
- rx_coalesce_usecs / ena_dev->intr_delay_resolution;
+ ena_dev->intr_moder_rx_interval = rx_coalesce_usecs /
+ ena_dev->intr_delay_resolution;
return 0;
}
@@ -2907,12 +2900,7 @@ unsigned int ena_com_get_nonadaptive_moderation_interval_tx(struct ena_com_dev *
unsigned int ena_com_get_nonadaptive_moderation_interval_rx(struct ena_com_dev *ena_dev)
{
- struct ena_intr_moder_entry *intr_moder_tbl = ena_dev->intr_moder_tbl;
-
- if (intr_moder_tbl)
- return intr_moder_tbl[ENA_INTR_MODER_LOWEST].intr_moder_interval;
-
- return 0;
+ return ena_dev->intr_moder_rx_interval;
}
void ena_com_init_intr_moderation_entry(struct ena_com_dev *ena_dev,
diff --git a/drivers/net/ethernet/amazon/ena/ena_com.h b/drivers/net/ethernet/amazon/ena/ena_com.h
index 0d3664fe260d..baeefc6af4f3 100644
--- a/drivers/net/ethernet/amazon/ena/ena_com.h
+++ b/drivers/net/ethernet/amazon/ena/ena_com.h
@@ -93,7 +93,7 @@
#define ENA_INTR_HIGHEST_BYTES (192 * 1024)
#define ENA_INTR_INITIAL_TX_INTERVAL_USECS 196
-#define ENA_INTR_INITIAL_RX_INTERVAL_USECS 4
+#define ENA_INTR_INITIAL_RX_INTERVAL_USECS 0
#define ENA_INTR_DELAY_OLD_VALUE_WEIGHT 6
#define ENA_INTR_DELAY_NEW_VALUE_WEIGHT 4
#define ENA_INTR_MODER_LEVEL_STRIDE 2
@@ -376,7 +376,13 @@ struct ena_com_dev {
struct ena_host_attribute host_attr;
bool adaptive_coalescing;
u16 intr_delay_resolution;
+
+ /* interrupt moderation intervals are in usec divided by
+ * intr_delay_resolution, which is supplied by the device.
+ */
u32 intr_moder_tx_interval;
+ u32 intr_moder_rx_interval;
+
struct ena_intr_moder_entry *intr_moder_tbl;
struct ena_com_llq_info llq_info;
diff --git a/drivers/net/ethernet/amazon/ena/ena_netdev.c b/drivers/net/ethernet/amazon/ena/ena_netdev.c
index 664e3ed97ea9..233b252ceb9e 100644
--- a/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ b/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -3485,10 +3485,11 @@ static int ena_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
calc_queue_ctx.get_feat_ctx = &get_feat_ctx;
calc_queue_ctx.pdev = pdev;
- /* initial Tx interrupt delay, Assumes 1 usec granularity.
+ /* Initial Tx and RX interrupt delay. Assumes 1 usec granularity.
* Updated during device initialization with the real granularity
*/
ena_dev->intr_moder_tx_interval = ENA_INTR_INITIAL_TX_INTERVAL_USECS;
+ ena_dev->intr_moder_rx_interval = ENA_INTR_INITIAL_RX_INTERVAL_USECS;
io_queue_num = ena_calc_io_queue_num(pdev, ena_dev, &get_feat_ctx);
rc = ena_calc_queue_size(&calc_queue_ctx);
if (rc || io_queue_num <= 0) {
--
2.17.2
^ permalink raw reply related
* pull-request: bpf-next 2019-09-16
From: Daniel Borkmann @ 2019-09-16 10:26 UTC (permalink / raw)
To: davem; +Cc: daniel, ast, netdev, bpf
Hi David,
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Now that initial BPF backend for gcc has been merged upstream, enable
BPF kselftest suite for bpf-gcc. Also fix a BE issue with access to
bpf_sysctl.file_pos, from Ilya.
2) Follow-up fix for link-vmlinux.sh to remove bash-specific extensions
related to recent work on exposing BTF info through sysfs, from Andrii.
3) AF_XDP zero copy fixes for i40e and ixgbe driver which caused umem
headroom to be added twice, from Ciara.
4) Refactoring work to convert sock opt tests into test_progs framework
in BPF kselftests, from Stanislav.
5) Fix a general protection fault in dev_map_hash_update_elem(), from Toke.
6) Cleanup to use BPF_PROG_RUN() macro in KCM, from Sami.
Please consider pulling these changes from:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git
Thanks a lot!
----------------------------------------------------------------
The following changes since commit 1e46c09ec10049a9e366153b32e41cc557383fdb:
Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next (2019-09-06 16:49:17 +0200)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git
for you to fetch changes up to d895a0f16fadb26d22ab531c49768f7642ae5c3e:
bpf: fix accessing bpf_sysctl.file_pos on s390 (2019-09-16 11:44:05 +0200)
----------------------------------------------------------------
Alexei Starovoitov (1):
Merge branch 'move-sockopt-tests'
Andrii Nakryiko (1):
kbuild: replace BASH-specific ${@:2} with shift and ${@}
Ciara Loftus (3):
i40e: fix xdp handle calculations
ixgbe: fix xdp handle calculations
samples/bpf: fix xdpsock l2fwd tx for unaligned mode
Daniel Borkmann (1):
Merge branch 'bpf-af-xdp-unaligned-fixes'
Ilya Leoshkevich (2):
selftests/bpf: add bpf-gcc support
bpf: fix accessing bpf_sysctl.file_pos on s390
Sami Tolvanen (1):
kcm: use BPF_PROG_RUN
Stanislav Fomichev (6):
selftests/bpf: test_progs: add test__join_cgroup helper
selftests/bpf: test_progs: convert test_sockopt
selftests/bpf: test_progs: convert test_sockopt_sk
selftests/bpf: test_progs: convert test_sockopt_multi
selftests/bpf: test_progs: convert test_sockopt_inherit
selftests/bpf: test_progs: convert test_tcp_rtt
Toke Høiland-Jørgensen (1):
xdp: Fix race in dev_map_hash_update_elem() when replacing element
drivers/net/ethernet/intel/i40e/i40e_xsk.c | 4 +-
drivers/net/ethernet/intel/ixgbe/ixgbe_xsk.c | 4 +-
include/linux/filter.h | 8 +-
kernel/bpf/cgroup.c | 10 +-
kernel/bpf/devmap.c | 17 +++-
kernel/bpf/verifier.c | 4 +-
net/kcm/kcmsock.c | 2 +-
samples/bpf/xdpsock_user.c | 2 +-
scripts/link-vmlinux.sh | 16 +++-
tools/testing/selftests/bpf/.gitignore | 5 -
tools/testing/selftests/bpf/Makefile | 77 +++++++++++-----
tools/testing/selftests/bpf/bpf_helpers.h | 24 +++--
.../bpf/{test_sockopt.c => prog_tests/sockopt.c} | 50 ++--------
.../sockopt_inherit.c} | 102 +++++++++------------
.../sockopt_multi.c} | 62 ++-----------
.../{test_sockopt_sk.c => prog_tests/sockopt_sk.c} | 60 +++---------
.../bpf/{test_tcp_rtt.c => prog_tests/tcp_rtt.c} | 83 ++++++-----------
tools/testing/selftests/bpf/progs/test_tc_edt.c | 1 +
tools/testing/selftests/bpf/test_progs.c | 38 ++++++++
tools/testing/selftests/bpf/test_progs.h | 4 +-
tools/testing/selftests/bpf/test_sysctl.c | 9 +-
21 files changed, 260 insertions(+), 322 deletions(-)
rename tools/testing/selftests/bpf/{test_sockopt.c => prog_tests/sockopt.c} (96%)
rename tools/testing/selftests/bpf/{test_sockopt_inherit.c => prog_tests/sockopt_inherit.c} (72%)
rename tools/testing/selftests/bpf/{test_sockopt_multi.c => prog_tests/sockopt_multi.c} (83%)
rename tools/testing/selftests/bpf/{test_sockopt_sk.c => prog_tests/sockopt_sk.c} (79%)
rename tools/testing/selftests/bpf/{test_tcp_rtt.c => prog_tests/tcp_rtt.c} (76%)
^ permalink raw reply
* [PATCH v3 bpf-next 00/14] samples: bpf: improve/fix cross-compilation
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
This series contains mainly fixes/improvements for cross-compilation
but not only, tested for arm, arm64, but intended for any arch.
Also verified on native build (not cross compilation) for x86_64
and arm.
Initial RFC link:
https://lkml.org/lkml/2019/8/29/1665
Prev. version:
https://lkml.org/lkml/2019/9/10/331
Besides the patches given here, the RFC also contains couple patches
related to llvm clang
arm: include: asm: swab: mask rev16 instruction for clang
arm: include: asm: unified: mask .syntax unified for clang
They are necessarily to verify arm build.
The change touches not only cross-compilation and can have impact on
other archs and build environments, so might be good idea to verify
it in order to add appropriate changes, some warn options could be
tuned also.
All is tested on x86-64 with clang installed (has to be built containing
targets for arm, arm64..., see llc --version, usually it's present already)
Instructions to test native on x86_64
=================================================
Native build on x86_64 is done in usual way and shouldn't have difference
except HOSTCC is now printed as CC wile building the samples.
Instructions to test cross compilation on arm64
=================================================
#Toolchain used for test:
gcc version 8.3.0
(GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))
# Get some arm64 FS, containing at least libelf
I've used sdk for TI am65x got here:
http://downloads.ti.com/processor-sdk-linux/esd/AM65X/latest/exports/\
ti-processor-sdk-linux-am65xx-evm-06.00.00.07-Linux-x86-Install.bin
# Install this binary to some dir, say "sdk".
# Configure kernel (use defconfig as no matter), but clean everything
# before.
make ARCH=arm64 -C tools/ clean
make ARCH=arm64 -C samples/bpf clean
make ARCH=arm64 clean
make ARCH=arm64 defconfig
# The kernel version used in sdk doesn't correspond to checked one,
# but for this verification only headers need to be syched,
# so install them:
make ARCH=arm64 headers_install
# or on SDK if need keep them in sync (not necessarily to verify):
make ARCH=arm64 INSTALL_HDR_PATH=/../sdk/\
ti-processor-sdk-linux-am65xx-evm-06.00.00.07/linux-devkit/sysroots/\
aarch64-linux/usr headers_install
# Build samples
make samples/bpf/ ARCH=arm64 CROSS_COMPILE="aarch64-linux-gnu-"\
SYSROOT="/../sdk/ti-processor-sdk-linux-am65xx-evm-06.00.00.07/\
linux-devkit/sysroots/aarch64-linux"
Instructions to test cross compilation on arm
=================================================
#Toolchains used for test:
arm-linux-gnueabihf-gcc (Linaro GCC 7.2-2017.11) 7.2.1 20171011
or
arm-linux-gnueabihf-gcc
(GNU Toolchain for the A-profile Architecture 8.3-2019.03 \
(arm-rel-8.36)) 8.3.0
# Get some FS, I've used sdk for TI am52xx got here:
http://downloads.ti.com/processor-sdk-linux/esd/AM57X/05_03_00_07/exports/\
ti-processor-sdk-linux-am57xx-evm-05.03.00.07-Linux-x86-Install.bin
# Install this binary to some dir, say "sdk".
# Configure kernel, but clean everything before.
make ARCH=arm -C tools/ clean
make ARCH=arm -C samples/bpf clean
make ARCH=arm clean
make ARCH=arm omap2plus_defconfig
# The kernel version used in sdk doesn't correspond to checked one, but
headers only should be synched, so install them:
make ARCH=arm64 headers_install
# or on SDK if need keep them in sync (not necessarily):
make ARCH=arm INSTALL_HDR_PATH=/../sdk/\
ti-processor-sdk-linux-am57xx-evm-05.03.00.07/linux-devkit/sysroots/\
armv7ahf-neon-linux-gnueabi/usr headers_install
# Build samples
make samples/bpf/ ARCH=arm CROSS_COMPILE="arm-linux-gnueabihf-"\
SYSROOT="/../sdk/ti-processor-sdk-linux-am57xx-evm-05.03\
.00.07/linux-devkit/sysroots/armv7ahf-neon-linux-gnueabi"
Based on bpf-next/master
v3..v2:
- renamed makefile.progs to makeifle.target, as more appropriate
- left only __LINUX_ARM_ARCH__ for D options for arm
- for host build - left options from KBUILD_HOST for compatibility reasons
- split patch adding c/cxx/ld flags to libbpf by modules
- moved readme change to separate patch
- added patch setting options for cross-compile
- fixed issue with option error for syscall_nrs.S,
avoiding overlap for ccflags-y.
v2..v1:
- restructured patches order
- split "samples: bpf: Makefile: base progs build on Makefile.progs"
to make change more readable. It added couple nice extra patches.
- removed redundant patch:
"samples: bpf: Makefile: remove target for native build"
- added fix:
"samples: bpf: makefile: fix cookie_uid_helper_example obj build"
- limited -D option filter only for arm
- improved comments
- added couple instructions to verify cross compilation for arm and
arm64 arches based on TI am57xx and am65xx sdks.
- corrected include a little order
Ivan Khoronzhuk (14):
samples: bpf: makefile: fix HDR_PROBE "echo"
samples: bpf: makefile: fix cookie_uid_helper_example obj build
samples: bpf: makefile: use --target from cross-compile
samples: bpf: use own EXTRA_CFLAGS for clang commands
samples: bpf: makefile: use __LINUX_ARM_ARCH__ selector for arm
samples: bpf: makefile: drop unnecessarily inclusion for bpf_load
samples: bpf: add makefile.target for separate CC target build
samples: bpf: makefile: base target programs rules on Makefile.target
samples: bpf: makefile: use own flags but not host when cross compile
samples: bpf: makefile: use target CC environment for HDR_PROBE
libbpf: makefile: add C/CXX/LDFLAGS to libbpf.so and test_libpf
targets
samples: bpf: makefile: provide C/CXX/LD flags to libbpf
samples: bpf: makefile: add sysroot support
samples: bpf: README: add preparation steps and sysroot info
samples/bpf/Makefile | 179 +++++++++++++++++++++---------------
samples/bpf/Makefile.target | 75 +++++++++++++++
samples/bpf/README.rst | 41 ++++++++-
tools/lib/bpf/Makefile | 11 ++-
4 files changed, 225 insertions(+), 81 deletions(-)
create mode 100644 samples/bpf/Makefile.target
--
2.17.1
^ permalink raw reply
* [PATCH v3 bpf-next 01/14] samples: bpf: makefile: fix HDR_PROBE "echo"
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
echo should be replaced with echo -e to handle '\n' correctly, but
instead, replace it with printf as some systems can't handle echo -e.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 1d9be26b4edd..f50ca852c2a8 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -201,7 +201,7 @@ endif
# Don't evaluate probes and warnings if we need to run make recursively
ifneq ($(src),)
-HDR_PROBE := $(shell echo "\#include <linux/types.h>\n struct list_head { int a; }; int main() { return 0; }" | \
+HDR_PROBE := $(shell printf "\#include <linux/types.h>\n struct list_head { int a; }; int main() { return 0; }" | \
$(HOSTCC) $(KBUILD_HOSTCFLAGS) -x c - -o /dev/null 2>/dev/null && \
echo okay)
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 03/14] samples: bpf: makefile: use --target from cross-compile
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
For cross compiling the target triple can be inherited from
cross-compile prefix as it's done in CLANG_FLAGS from kernel makefile.
So copy-paste this decision from kernel Makefile.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 43dee90dffa4..b59e77e2250e 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -195,7 +195,7 @@ BTF_PAHOLE ?= pahole
# Detect that we're cross compiling and use the cross compiler
ifdef CROSS_COMPILE
HOSTCC = $(CROSS_COMPILE)gcc
-CLANG_ARCH_ARGS = -target $(ARCH)
+CLANG_ARCH_ARGS = --target=$(notdir $(CROSS_COMPILE:%-=%))
endif
# Don't evaluate probes and warnings if we need to run make recursively
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 02/14] samples: bpf: makefile: fix cookie_uid_helper_example obj build
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
Don't list userspace "cookie_uid_helper_example" object in list for
bpf objects.
'always' target is used for listing bpf programs, but
'cookie_uid_helper_example.o' is a user space ELF file, and covered
by rule `per_socket_stats_example`, so shouldn't be in 'always'.
Let us remove `always += cookie_uid_helper_example.o`, which avoids
breaking cross compilation due to mismatched includes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 1 -
1 file changed, 1 deletion(-)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index f50ca852c2a8..43dee90dffa4 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -145,7 +145,6 @@ always += sampleip_kern.o
always += lwt_len_hist_kern.o
always += xdp_tx_iptunnel_kern.o
always += test_map_in_map_kern.o
-always += cookie_uid_helper_example.o
always += tcp_synrto_kern.o
always += tcp_rwnd_kern.o
always += tcp_bufs_kern.o
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 05/14] samples: bpf: makefile: use __LINUX_ARM_ARCH__ selector for arm
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
For arm, -D__LINUX_ARM_ARCH__=X is min version used as instruction
set selector and is absolutely required while parsing some parts of
headers. It's present in KBUILD_CFLAGS but not in autoconf.h, so let's
retrieve it from and add to programs cflags. In another case errors
like "SMP is not supported" for armv7 and bunch of other errors are
issued resulting to incorrect final object.
---
samples/bpf/Makefile | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 8ecc5d0c2d5b..d3c8db3df560 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -185,6 +185,16 @@ HOSTLDLIBS_map_perf_test += -lrt
HOSTLDLIBS_test_overhead += -lrt
HOSTLDLIBS_xdpsock += -pthread
+ifeq ($(ARCH), arm)
+# Strip all except -D__LINUX_ARM_ARCH__ option needed to handle linux
+# headers when arm instruction set identification is requested.
+ARM_ARCH_SELECTOR = $(shell echo "$(KBUILD_CFLAGS) " | \
+ sed 's/[[:blank:]]/\n/g' | sed '/^-D__LINUX_ARM_ARCH__/!d')
+
+CLANG_EXTRA_CFLAGS := $(ARM_ARCH_SELECTOR)
+KBUILD_HOSTCFLAGS := $(ARM_ARCH_SELECTOR)
+endif
+
# Allows pointing LLC/CLANG to a LLVM backend with bpf support, redefine on cmdline:
# make samples/bpf/ LLC=~/git/llvm/build/bin/llc CLANG=~/git/llvm/build/bin/clang
LLC ?= llc
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 06/14] samples: bpf: makefile: drop unnecessarily inclusion for bpf_load
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
Drop inclusion for bpf_load -I$(objtree)/usr/include as it is
included for all objects anyway, with above line:
KBUILD_HOSTCFLAGS += -I$(objtree)/usr/include
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index d3c8db3df560..9d923546e087 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -176,7 +176,7 @@ KBUILD_HOSTCFLAGS += -I$(srctree)/tools/testing/selftests/bpf/
KBUILD_HOSTCFLAGS += -I$(srctree)/tools/lib/ -I$(srctree)/tools/include
KBUILD_HOSTCFLAGS += -I$(srctree)/tools/perf
-HOSTCFLAGS_bpf_load.o += -I$(objtree)/usr/include -Wno-unused-variable
+HOSTCFLAGS_bpf_load.o += -Wno-unused-variable
KBUILD_HOSTLDLIBS += $(LIBBPF) -lelf
HOSTLDLIBS_tracex4 += -lrt
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 07/14] samples: bpf: add makefile.target for separate CC target build
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
The makefile.target is added only and will be used in
sample/bpf/Makefile later in order to switch cross-compiling on CC
from HOSTCC environment.
The HOSTCC is supposed to build binaries and tools running on the host
afterwards, in order to simplify build or so, like "fixdep" or else.
In case of cross compiling "fixdep" is executed on host when the rest
samples should run on target arch. In order to build binaries for
target arch with CC and tools running on host with HOSTCC, lets add
Makefile.target for simplicity, having definition and routines similar
to ones, used in script/Makefile.host. This allows later add
cross-compilation to samples/bpf with minimum changes.
The tprog stands for target programs built with CC.
Makefile.target contains only stuff needed for samples/bpf, potentially
can be reused later and now needed only for unblocking tricky
samples/bpf cross compilation.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile.target | 75 +++++++++++++++++++++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 samples/bpf/Makefile.target
diff --git a/samples/bpf/Makefile.target b/samples/bpf/Makefile.target
new file mode 100644
index 000000000000..fb6de63f7d2f
--- /dev/null
+++ b/samples/bpf/Makefile.target
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: GPL-2.0
+# ==========================================================================
+# Building binaries on the host system
+# Binaries are not used during the compilation of the kernel, and intendent
+# to be build for target board, target board can be host ofc. Added to build
+# binaries to run not on host system.
+#
+# Sample syntax (see Documentation/kbuild/makefiles.rst for reference)
+# tprogs-y := xsk_example
+# Will compile xdpsock_example.c and create an executable named xsk_example
+#
+# tprogs-y := xdpsock
+# xdpsock-objs := xdpsock_1.o xdpsock_2.o
+# Will compile xdpsock_1.c and xdpsock_2.c, and then link the executable
+# xdpsock, based on xdpsock_1.o and xdpsock_2.o
+#
+# Inherited from scripts/Makefile.host
+#
+__tprogs := $(sort $(tprogs-y))
+
+# C code
+# Executables compiled from a single .c file
+tprog-csingle := $(foreach m,$(__tprogs), \
+ $(if $($(m)-objs),,$(m)))
+
+# C executables linked based on several .o files
+tprog-cmulti := $(foreach m,$(__tprogs),\
+ $(if $($(m)-objs),$(m)))
+
+# Object (.o) files compiled from .c files
+tprog-cobjs := $(sort $(foreach m,$(__tprogs),$($(m)-objs)))
+
+tprog-csingle := $(addprefix $(obj)/,$(tprog-csingle))
+tprog-cmulti := $(addprefix $(obj)/,$(tprog-cmulti))
+tprog-cobjs := $(addprefix $(obj)/,$(tprog-cobjs))
+
+#####
+# Handle options to gcc. Support building with separate output directory
+
+_tprogc_flags = $(TPROGS_CFLAGS) \
+ $(TPROGCFLAGS_$(basetarget).o)
+
+# $(objtree)/$(obj) for including generated headers from checkin source files
+ifeq ($(KBUILD_EXTMOD),)
+ifdef building_out_of_srctree
+_tprogc_flags += -I $(objtree)/$(obj)
+endif
+endif
+
+tprogc_flags = -Wp,-MD,$(depfile) $(_tprogc_flags)
+
+# Create executable from a single .c file
+# tprog-csingle -> Executable
+quiet_cmd_tprog-csingle = CC $@
+ cmd_tprog-csingle = $(CC) $(tprogc_flags) $(TPROGS_LDFLAGS) -o $@ $< \
+ $(TPROGS_LDLIBS) $(TPROGLDLIBS_$(@F))
+$(tprog-csingle): $(obj)/%: $(src)/%.c FORCE
+ $(call if_changed_dep,tprog-csingle)
+
+# Link an executable based on list of .o files, all plain c
+# tprog-cmulti -> executable
+quiet_cmd_tprog-cmulti = LD $@
+ cmd_tprog-cmulti = $(CC) $(tprogc_flags) $(TPROGS_LDFLAGS) -o $@ \
+ $(addprefix $(obj)/,$($(@F)-objs)) \
+ $(TPROGS_LDLIBS) $(TPROGLDLIBS_$(@F))
+$(tprog-cmulti): $(tprog-cobjs) FORCE
+ $(call if_changed,tprog-cmulti)
+$(call multi_depend, $(tprog-cmulti), , -objs)
+
+# Create .o file from a single .c file
+# tprog-cobjs -> .o
+quiet_cmd_tprog-cobjs = CC $@
+ cmd_tprog-cobjs = $(CC) $(tprogc_flags) -c -o $@ $<
+$(tprog-cobjs): $(obj)/%.o: $(src)/%.c FORCE
+ $(call if_changed_dep,tprog-cobjs)
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 11/14] libbpf: makefile: add C/CXX/LDFLAGS to libbpf.so and test_libpf targets
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
In case of LDFLAGS and EXTRA_CC/CXX flags there is no way to pass them
correctly to build command, for instance when --sysroot is used or
external libraries are used, like -lelf, wich can be absent in
toolchain. This can be used for samples/bpf cross-compiling allowing
to get elf lib from sysroot.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
tools/lib/bpf/Makefile | 11 ++++++++---
1 file changed, 8 insertions(+), 3 deletions(-)
diff --git a/tools/lib/bpf/Makefile b/tools/lib/bpf/Makefile
index c6f94cffe06e..bccfa556ef4e 100644
--- a/tools/lib/bpf/Makefile
+++ b/tools/lib/bpf/Makefile
@@ -94,6 +94,10 @@ else
CFLAGS := -g -Wall
endif
+ifdef EXTRA_CXXFLAGS
+ CXXFLAGS := $(EXTRA_CXXFLAGS)
+endif
+
ifeq ($(feature-libelf-mmap), 1)
override CFLAGS += -DHAVE_LIBELF_MMAP_SUPPORT
endif
@@ -176,8 +180,9 @@ $(BPF_IN): force elfdep bpfdep
$(OUTPUT)libbpf.so: $(OUTPUT)libbpf.so.$(LIBBPF_VERSION)
$(OUTPUT)libbpf.so.$(LIBBPF_VERSION): $(BPF_IN)
- $(QUIET_LINK)$(CC) --shared -Wl,-soname,libbpf.so.$(LIBBPF_MAJOR_VERSION) \
- -Wl,--version-script=$(VERSION_SCRIPT) $^ -lelf -o $@
+ $(QUIET_LINK)$(CC) $(LDFLAGS) \
+ --shared -Wl,-soname,libbpf.so.$(LIBBPF_MAJOR_VERSION) \
+ -Wl,--version-script=$(VERSION_SCRIPT) $^ -lelf -o $@
@ln -sf $(@F) $(OUTPUT)libbpf.so
@ln -sf $(@F) $(OUTPUT)libbpf.so.$(LIBBPF_MAJOR_VERSION)
@@ -185,7 +190,7 @@ $(OUTPUT)libbpf.a: $(BPF_IN)
$(QUIET_LINK)$(RM) $@; $(AR) rcs $@ $^
$(OUTPUT)test_libbpf: test_libbpf.cpp $(OUTPUT)libbpf.a
- $(QUIET_LINK)$(CXX) $(INCLUDES) $^ -lelf -o $@
+ $(QUIET_LINK)$(CXX) $(CXXFLAGS) $(LDFLAGS) $(INCLUDES) $^ -lelf -o $@
$(OUTPUT)libbpf.pc:
$(QUIET_GEN)sed -e "s|@PREFIX@|$(prefix)|" \
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 13/14] samples: bpf: makefile: add sysroot support
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
Basically it only enables that was added by previous couple fixes.
Sysroot contains correct libs installed and its headers ofc. Useful
when working with NFC or virtual machine.
Usage:
clean (on demand)
make ARCH=arm -C samples/bpf clean
make ARCH=arm -C tools clean
make ARCH=arm clean
configure and install headers:
make ARCH=arm defconfig
make ARCH=arm headers_install
build samples/bpf:
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- samples/bpf/ \
SYSROOT="path/to/sysroot"
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 133123d4c7d7..57ddf055d6c3 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -194,6 +194,11 @@ TPROGS_CFLAGS += -I$(srctree)/tools/lib/
TPROGS_CFLAGS += -I$(srctree)/tools/include
TPROGS_CFLAGS += -I$(srctree)/tools/perf
+ifdef SYSROOT
+TPROGS_CFLAGS += --sysroot=${SYSROOT}
+TPROGS_LDFLAGS := -L${SYSROOT}/usr/lib
+endif
+
EXTRA_CXXFLAGS := $(TPROGS_CFLAGS)
# options not valid for C++
--
2.17.1
^ permalink raw reply related
* [PATCH v3 bpf-next 12/14] samples: bpf: makefile: provide C/CXX/LD flags to libbpf
From: Ivan Khoronzhuk @ 2019-09-16 10:54 UTC (permalink / raw)
To: ast, daniel, yhs, davem, jakub.kicinski, hawk, john.fastabend
Cc: linux-kernel, netdev, bpf, clang-built-linux, sergei.shtylyov,
Ivan Khoronzhuk
In-Reply-To: <20190916105433.11404-1-ivan.khoronzhuk@linaro.org>
In order to build libs using C/CXX/LD flags of target arch,
provide them to libbpf make.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
samples/bpf/Makefile | 14 +++++++++++---
1 file changed, 11 insertions(+), 3 deletions(-)
diff --git a/samples/bpf/Makefile b/samples/bpf/Makefile
index 18ec22e7b444..133123d4c7d7 100644
--- a/samples/bpf/Makefile
+++ b/samples/bpf/Makefile
@@ -182,8 +182,6 @@ ifdef CROSS_COMPILE
TPROGS_CFLAGS += -Wall
TPROGS_CFLAGS += -O2
TPROGS_CFLAGS += -fomit-frame-pointer
-TPROGS_CFLAGS += -Wmissing-prototypes
-TPROGS_CFLAGS += -Wstrict-prototypes
else
TPROGS_LDLIBS := $(KBUILD_HOSTLDLIBS)
TPROGS_CFLAGS += $(KBUILD_HOSTCFLAGS) $(HOST_EXTRACFLAGS)
@@ -196,6 +194,14 @@ TPROGS_CFLAGS += -I$(srctree)/tools/lib/
TPROGS_CFLAGS += -I$(srctree)/tools/include
TPROGS_CFLAGS += -I$(srctree)/tools/perf
+EXTRA_CXXFLAGS := $(TPROGS_CFLAGS)
+
+# options not valid for C++
+ifdef CROSS_COMPILE
+$(TPROGS_CFLAGS) += -Wmissing-prototypes
+$(TPROGS_CFLAGS) += -Wstrict-prototypes
+endif
+
TPROGCFLAGS_bpf_load.o += -Wno-unused-variable
TPROGS_LDLIBS += $(LIBBPF) -lelf
@@ -257,7 +263,9 @@ clean:
$(LIBBPF): FORCE
# Fix up variables inherited from Kbuild that tools/ build system won't like
- $(MAKE) -C $(dir $@) RM='rm -rf' LDFLAGS= srctree=$(BPF_SAMPLES_PATH)/../../ O=
+ $(MAKE) -C $(dir $@) RM='rm -rf' EXTRA_CFLAGS="$(TPROGS_CFLAGS)" \
+ EXTRA_CXXFLAGS="$(EXTRA_CXXFLAGS)" LDFLAGS=$(TPROGS_LDFLAGS) \
+ srctree=$(BPF_SAMPLES_PATH)/../../ O=
$(obj)/syscall_nrs.h: $(obj)/syscall_nrs.s FORCE
$(call filechk,offsets,__SYSCALL_NRS_H__)
--
2.17.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox