From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jason Lunz Subject: Re: e100-3.0.0_dev8 "Minneapolis Moline" release Date: Wed, 18 Jun 2003 15:54:32 +0000 (UTC) Sender: netdev-bounce@oss.sgi.com Message-ID: References: Return-path: To: netdev@oss.sgi.com Errors-to: netdev-bounce@oss.sgi.com List-Id: netdev.vger.kernel.org scott.feldman@intel.com said: > Your help in testing would be greatly appreciated. There are many 8255x > devices supported by e100, so hopefully we'll get good coverage from the > community. It's running on my workstation with no problems. passes the "ping -qf" load test. lspci says I have: 00:0b.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at d8100000 (32-bit, non-prefetchable) [size=4K] I/O ports at e800 [size=64] Memory at d8000000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at [disabled] [size=1M] Capabilities: [dc] Power Management version 2 ethtool output seems normal, but what's with the rx-mini and rx-jumbo max settings in the -g output? [stoli](0) # ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Half Port: MII PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x00000007 (7) Link detected: yes [stoli](0) # ethtool -a eth0 Pause parameters for eth0: Cannot get device pause settings: Operation not supported [stoli](76) # ethtool -c eth0 Coalesce parameters for eth0: Cannot get device coalesce settings: Operation not supported [stoli](82) # ethtool -g eth0 Ring parameters for eth0: Pre-set maximums: RX: 256 RX Mini: 134512692 RX Jumbo: 134512692 TX: 256 Current hardware settings: RX: 64 RX Mini: 5 RX Jumbo: 4 TX: 64 [stoli](0) # ethtool -i eth0 driver: e100 version: 3.0.0_dev8 firmware-version: N/A bus-info: 00:0b.0 [stoli](0) # ethtool -d eth0 SCB Status and Command Word ------------- SCB Status Word (Lower Word) 0x0050 RU Status: Ready CU Status: Suspended ---- Interrupts Pending ---- Flow Control Pause: no Early Receive: no Software Generated Interrupt: no MDI Done: no RU Not In Ready State: no CU Not in Active State: no RU Received Frame: no CU Completed Command: no SCB Command Word (Upper Word) 0x0000 RU Command: No Command CU Command: No Command Software Generated Interrupt: no ---- Interrupts Masked ---- ALL Interrupts: no Flow Control Pause: no Early Receive: no RU Not In Ready State: no CU Not in Active State: no RU Received Frame: no CU Completed Command: no [stoli](0) # ethtool -e eth0 Offset Values ------ ------ 0x0000 00 02 b3 11 b9 e0 03 02 00 00 01 02 01 47 00 00 0x0010 13 72 10 83 a2 40 0c 00 86 80 00 00 00 00 00 00 0x0020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0060 a8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4a c3 [stoli](0) # ethtool -k eth0 RX/TX checksumming parameters for eth0: Cannot get device rx csum settings: Operation not supported Cannot get device tx csum settings: Operation not supported Cannot get device scatter-gather settings: Operation not supported no checksumming/SG info available [stoli](83) # ethtool -p eth0 [stoli](130) # ethtool -r eth0 [stoli](0) # ethtool -S eth0 NIC statistics: rx_packets: 1410143 tx_packets: 1410029 rx_bytes: 138271433 tx_bytes: 138179379 rx_errors: 41 tx_errors: 0 rx_dropped: 0 tx_dropped: 0 multicast: 0 collisions: 136914 rx_length_errors: 41 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_fifo_errors: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 [stoli](0) # ethtool -t eth0 online The test result is PASS The test extra info: Link test (on/offline) 0 Eeprom test (on/offline) 0 Self test (offline) 0 Mac loopback (offline) 0 Phy loopback (offline) 0 [stoli](0) # ethtool -t eth0 offline The test result is PASS The test extra info: Link test (on/offline) 0 Eeprom test (on/offline) 0 Self test (offline) 0 Mac loopback (offline) 0 Phy loopback (offline) 0 -- Jason Lunz Reflex Security lunz@reflexsecurity.com http://www.reflexsecurity.com/