Re: [PATCH net v5] net: use skb_header_pointer() only for DODGY TCPv4 GSO skbs

[Willem de Bruijn <willemdebruijn.kernel@gmail.com>]

Willem de Bruijn wrote:
> Guoyu Su wrote:
> > Syzbot reported a KMSAN uninit-value warning in gso_features_check()
> > called from netif_skb_features() [1].
> > 
> > The current direct skb->len check is not sufficient for SKB_GSO_DODGY
> > packets. In the AF_PACKET/PACKET_VNET_HDR path, packet_snd() can build
> > a DODGY GSO skb whose total length is large enough, while the IPv4
> > header is not fully available as initialized linear data for a direct
> > iph->frag_off access.
> 
> The fix looks fine, but the AI review of an earlier revision brings up
> a good point: __virtio_net_hdr_to_skb calls pskb_may_pull in all paths
> to ensure the network header is fully in skb linear. What kind of packet
> is this that managed to escape those checks?

The packets I got out of the C repro just after virtio_net_hdr_to_skb
look as below.

[   76.539562] vnet_hdr: flags=0x75 gso_type=0x1 hlen=0x6a gso_sz=0x416d cstart=0x58
[   76.539755] skb len=56584 data_len=56476 headroom=4 headlen=108 tailroom=0
[   76.539755] end-tail=208 mac=(4,76) mac_len=0 net=(80,12) trans=92
[   76.539755] shinfo(txflags=0 nr_frags=3 gso(size=16749 type=3 segs=0))
[   76.539755] csum(0x10005c start=92 offset=16 ip_summed=3 complete_sw=0 valid=0 level=0)
[   76.539755] hash(0x0 sw=0 l4=0) proto=0x0800 pkttype=0 iif=0
[   76.539755] priority=0x0 mark=0x0 alloc_cpu=0 vlan_all=0x0
[   76.539755] encapsulation=0 inner(proto=0x0000, mac=0, net=0, trans=0)
[   76.540713] dev name=ip6gretap0 feat=0x0000000e401d4869
[   76.540843] sk family=17 type=3 proto=0

Clearly fishy. They do have VIRTIO_NET_HDR_F_NEEDS_CSUM set, so we
know which branch they take.

        skb_reset_mac_header(skb);
        
        if (hdr->flags & VIRTIO_NET_HDR_F_NEEDS_CSUM) {
                u32 start = __virtio16_to_cpu(little_endian, hdr->csum_start);
                u32 off = __virtio16_to_cpu(little_endian, hdr->csum_offset);
                u32 needed = start + max_t(u32, thlen, off + sizeof(__sum16));

// start == 88
// needed == 88 + 18 == 106

                if (!pskb_may_pull(skb, needed))
                        return -EINVAL;

                if (!skb_partial_csum_set(skb, start, off))
                        return -EINVAL;
                if (skb_transport_offset(skb) < nh_min_len)
                        return -EINVAL;

                nh_min_len = skb_transport_offset(skb);

// nh_min_len == 88

                p_off = nh_min_len + thlen;

// p_off == 108

                if (!pskb_may_pull(skb, p_off))
                        return -EINVAL;

// headlen == 108

At the end of this headlen == 108, so all of iphdr should be in
linear.

Since the syz repro requires repeat it is possible that I simply did
not capture the right packet, but I don't see the C program vary the
packet contents.