From: Florian Westphal <fw@strlen.de>
To: <netfilter-devel@vger.kernel.org>
Cc: Florian Westphal <fw@strlen.de>
Subject: [PATCH nf 4/4] netfilter: nfnetlink_log: rework mac header logging
Date: Fri, 30 Oct 2026 16:44:33 +0100 [thread overview]
Message-ID: <20261030154433.13601-5-fw@strlen.de> (raw)
In-Reply-To: <20261030154433.13601-1-fw@strlen.de>
For unknown reasons this uses dev->hard_header_len.
LLM says that hard_header_len says how long a link layer header can get,
not how many bytes this packet holds. Use skb_mac_header_len instead and
cap if needed.
AFAICS this should have dumped skb_mac_header_len bytes instead, with one
single attribute (plus maybe skb->protocol).
Keep it close to the original version: if hard_header_len is larger than
the mac header size of the packet, then clamp to that value.
While at it, also move this so that we don't call this for POST_ROUTING
hook; mac header is still that of the incoming device, not the egress one.
I suspect that this is almost exclusively used with plain ethernet,
where hard_header_len and skb_mac_header_len() are 14 bytes which
would explain absence of bug reports.
Fixes: 72961ecf84d6 ("netfilter: nfnetlink_log: send complete hardware header")
Signed-off-by: Florian Westphal <fw@strlen.de>
---
net/netfilter/nfnetlink_log.c | 68 +++++++++++++++++++++++++++--------
1 file changed, 54 insertions(+), 14 deletions(-)
diff --git a/net/netfilter/nfnetlink_log.c b/net/netfilter/nfnetlink_log.c
index 29530b753928..e6877ac36d26 100644
--- a/net/netfilter/nfnetlink_log.c
+++ b/net/netfilter/nfnetlink_log.c
@@ -458,6 +458,56 @@ static int nfulnl_put_bridge(struct nfulnl_instance *inst, const struct sk_buff
return -1;
}
+/**
+ * nfulnl_put_hwheader - Append link-layer header info to the netlink skb.
+ * @nlskb: Target netlink message to append attributes to.
+ * @skb: Original packet skb whose link-layer header is described.
+ *
+ * Emits the NFULA_HWTYPE and NFULA_HWLEN netlink attributes into @nlskb
+ * based on the link-layer header of @skb.
+ *
+ * The device's hard_header_len describes the maximum size a link-layer
+ * header can grow to, not the actual size of this packet's header.
+ * The actual length is taken from skb_mac_header_len() and capped at
+ * hard_header_len if needed.
+ *
+ * The NFULA_HWLEN attribute is retained for backward compatibility.
+ * Userspace should derive the length from the NFULA_HWHEADER attribute
+ * size instead.
+ *
+ * Caller must check skb_mac_header_was_set(skb) before using this
+ * function.
+ *
+ * Return: -EMSGSIZE if the tailroom of the skb is insufficient to store
+ * the attribute header and payload.
+ */
+static int nfulnl_put_hwheader(struct sk_buff *nlskb, const struct sk_buff *skb)
+{
+ unsigned int hwlen = READ_ONCE(skb->dev->hard_header_len);
+ const unsigned char *hwhdrp = skb_mac_header(skb);
+ int len = skb_mac_header_len(skb);
+ u16 hwtype = skb->dev->type;
+
+ if (nla_put_be16(nlskb, NFULA_HWTYPE, htons(hwtype)))
+ return -EMSGSIZE;
+
+ if (len > hwlen)
+ len = hwlen;
+
+ /* This attribute should not exist, userspace should
+ * use NFULA_HWHEADER attribute size. Removing
+ * this breaks existing users which unfortunately
+ * rely on NFULA_HWLEN presence.
+ */
+ if (nla_put_be16(nlskb, NFULA_HWLEN, htons(len)))
+ return -EMSGSIZE;
+
+ if (len == 0)
+ return 0;
+
+ return nla_put(nlskb, NFULA_HWHEADER, len, hwhdrp);
+}
+
#if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
static int nflog_put_master_ifindex(struct sk_buff *nlskb, int attr,
const struct net_device *dev)
@@ -494,7 +544,6 @@ __build_packet_message(struct nfnl_log_net *log,
struct nlmsghdr *nlh;
sk_buff_data_t old_tail = inst->skb->tail;
struct sock *sk;
- const unsigned char *hwhdrp;
nlh = nfnl_msg_put(inst->skb, 0, 0,
nfnl_msg_type(NFNL_SUBSYS_ULOG, NFULNL_MSG_PACKET),
@@ -592,25 +641,16 @@ __build_packet_message(struct nfnl_log_net *log,
if (nfnetlink_put_hwaddr(inst->skb, skb, indev, NFULA_HWADDR))
goto nla_put_failure;
- if (indev && skb_mac_header_was_set(skb)) {
- if (nla_put_be16(inst->skb, NFULA_HWTYPE, htons(skb->dev->type)) ||
- nla_put_be16(inst->skb, NFULA_HWLEN,
- htons(skb->dev->hard_header_len)))
- goto nla_put_failure;
-
- hwhdrp = skb_mac_header(skb);
-
- if (nla_put(inst->skb, NFULA_HWHEADER,
- skb->dev->hard_header_len, hwhdrp))
- goto nla_put_failure;
- }
-
if (hooknum <= NF_INET_FORWARD) {
struct timespec64 kts = ktime_to_timespec64(skb_tstamp_cond(skb, true));
struct nfulnl_msg_packet_timestamp ts;
ts.sec = cpu_to_be64(kts.tv_sec);
ts.usec = cpu_to_be64(kts.tv_nsec / NSEC_PER_USEC);
+ if (indev && skb->dev && skb_mac_header_was_set(skb) &&
+ nfulnl_put_hwheader(inst->skb, skb))
+ goto nla_put_failure;
+
if (nla_put(inst->skb, NFULA_TIMESTAMP, sizeof(ts), &ts))
goto nla_put_failure;
}
--
2.56.0
next prev parent reply other threads:[~2026-10-30 15:45 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-30 15:44 [PATCH nf 0/4] netfilter: logging cleanups Florian Westphal
2026-10-30 15:44 ` [PATCH nf 1/4] netfilter: nf_log: remove dead ARPHRD_SIT handling from MAC/HW header logging Florian Westphal
2026-10-30 15:44 ` [PATCH nf 2/4] netfilter: nf_log_syslog: fix MAC header dump to use real header length Florian Westphal
2026-10-30 15:44 ` [PATCH nf 3/4] netfilter: nfnetlink_log: fix up dev_parse_header usage Florian Westphal
2026-10-30 15:44 ` Florian Westphal [this message]
2026-10-31 18:34 ` [PATCH nf 0/4] netfilter: logging cleanups Florian Westphal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261030154433.13601-5-fw@strlen.de \
--to=fw@strlen.de \
--cc=netfilter-devel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox