From: Emre Cecanpunar <emreleno@gmail.com>
To: platform-driver-x86@vger.kernel.org
Cc: hansg@kernel.org, ilpo.jarvinen@linux.intel.com,
linux-kernel@vger.kernel.org, krishna.chomal108@gmail.com,
Emre Cecanpunar <emreleno@gmail.com>
Subject: [PATCH v2 4/5] platform/x86: hp-wmi: fix u8 underflow in gpu_delta calculation
Date: Sun, 22 Mar 2026 22:06:23 +0300 [thread overview]
Message-ID: <20260322190624.35162-5-emreleno@gmail.com> (raw)
In-Reply-To: <20260322190624.35162-1-emreleno@gmail.com>
gpu_delta was declared as u8 and computed as the difference of two u8
fan RPM values from the firmware fan table. If gpu_rpm < cpu_rpm, the
subtraction wraps around modulo 256, producing a large positive value
(e.g. 10 - 20 = 246 as u8). This value is then added to every
requested fan speed in hp_wmi_fan_speed_set(), causing the GPU fan to
be clamped to U8_MAX on almost every write.
Change gpu_delta to int in both struct hp_wmi_hwmon_priv and
hp_wmi_setup_fan_settings(), and perform the subtraction in signed
arithmetic. hp_wmi_fan_speed_set() already uses signed arithmetic with
clamp_val(), so a negative delta correctly results in a lower GPU fan
speed rather than saturating at U8_MAX.
Signed-off-by: Emre Cecanpunar <emreleno@gmail.com>
---
Changes in v2:
- Drop the if (gpu_delta < 0) guard and pr_warn. A negative delta is
valid firmware behavior on boards where CPU_RPM > GPU_RPM. Store
gpu_delta as int in struct hp_wmi_hwmon_priv so the existing signed
arithmetic and clamp_val() in hp_wmi_fan_speed_set() handle the
negative case correctly without saturating at U8_MAX.
drivers/platform/x86/hp/hp-wmi.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/platform/x86/hp/hp-wmi.c b/drivers/platform/x86/hp/hp-wmi.c
index a29f34588055..af57cb0dbf9e 100644
--- a/drivers/platform/x86/hp/hp-wmi.c
+++ b/drivers/platform/x86/hp/hp-wmi.c
@@ -436,7 +436,7 @@ enum pwm_modes {
struct hp_wmi_hwmon_priv {
u8 min_rpm;
u8 max_rpm;
- u8 gpu_delta;
+ int gpu_delta;
u8 mode;
u8 pwm;
struct delayed_work keep_alive_dwork;
@@ -2530,8 +2530,8 @@ static int hp_wmi_setup_fan_settings(struct hp_wmi_hwmon_priv *priv)
{
u8 fan_data[128] = { 0 };
struct victus_s_fan_table *fan_table;
- u8 min_rpm, max_rpm, gpu_delta;
- int ret;
+ u8 min_rpm, max_rpm;
+ int gpu_delta, ret;
/* Default behaviour on hwmon init is automatic mode */
priv->mode = PWM_MODE_AUTO;
@@ -2553,7 +2553,8 @@ static int hp_wmi_setup_fan_settings(struct hp_wmi_hwmon_priv *priv)
min_rpm = fan_table->entries[0].cpu_rpm;
max_rpm = fan_table->entries[fan_table->header.num_entries - 1].cpu_rpm;
- gpu_delta = fan_table->entries[0].gpu_rpm - fan_table->entries[0].cpu_rpm;
+ gpu_delta = (int)fan_table->entries[0].gpu_rpm -
+ (int)fan_table->entries[0].cpu_rpm;
priv->min_rpm = min_rpm;
priv->max_rpm = max_rpm;
priv->gpu_delta = gpu_delta;
--
2.53.0
next prev parent reply other threads:[~2026-03-22 19:07 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-03-22 19:06 [PATCH v2 0/5] platform/x86: hp-wmi: Victus S fan control fixes Emre Cecanpunar
2026-03-22 19:06 ` [PATCH v2 1/5] platform/x86: hp-wmi: fix ignored return values in fan settings Emre Cecanpunar
2026-03-22 19:06 ` [PATCH v2 2/5] platform/x86: hp-wmi: avoid cancel_delayed_work_sync from work handler Emre Cecanpunar
2026-03-22 19:06 ` [PATCH v2 3/5] platform/x86: hp-wmi: use mod_delayed_work to reset keep-alive timer Emre Cecanpunar
2026-03-23 9:51 ` Ilpo Järvinen
2026-03-22 19:06 ` Emre Cecanpunar [this message]
2026-03-23 9:42 ` [PATCH v2 4/5] platform/x86: hp-wmi: fix u8 underflow in gpu_delta calculation Ilpo Järvinen
2026-03-22 19:06 ` [PATCH v2 5/5] platform/x86: hp-wmi: add locking for concurrent hwmon access Emre Cecanpunar
2026-03-24 15:46 ` [PATCH v2 0/5] platform/x86: hp-wmi: Victus S fan control fixes Ilpo Järvinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260322190624.35162-5-emreleno@gmail.com \
--to=emreleno@gmail.com \
--cc=hansg@kernel.org \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=krishna.chomal108@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=platform-driver-x86@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox