Poky Project Discussions
 help / color / mirror / Atom feed
From: Gary Thomas <gary@mlbassoc.com>
To: Poky Project <poky@yoctoproject.org>
Subject: Re: Early image startup
Date: Fri, 08 Apr 2011 07:29:31 -0600	[thread overview]
Message-ID: <4D9F0DBB.8070608@mlbassoc.com> (raw)
In-Reply-To: <4D9F0B82.9080803@mlbassoc.com>

On 04/08/2011 07:20 AM, Gary Thomas wrote:
> I have a Poky image which uses a number of kernel modules. For
> whatever reason, the raw image has not had the modules configured
> (no /lib/modules/.../modules.dep) This file is created by 'update-modules'
> but that is run too late in the boot process. The problem is that
> other code, e.g. I'm using iptables via modules, requires the modules
> be configured early and this fails. If I reboot (after 'update-modules'
> has run), everything is fine.
>
> My system is PowerPC and I'm using ipk packaging.
>
> Here's a snippet from my initial boot log:
> Please wait: booting...
> Starting udev
> Configuring network interfaces... udhcpc (v1.17.3) started
> Setting IP address 0.0.0.0 on eth0
> Sending discover...
> PHY: mdio@ff024520:01 - Link is Up - 1000/Full
> Sending discover...
> Sending select for 192.168.12.140...
> Lease of 192.168.12.140 obtained, lease time 600
> Setting IP address 192.168.12.140 on eth0
> Deleting routers
> Adding router 192.168.12.1
> Recreating /etc/resolv.conf
> Adding DNS server 192.168.12.1
> done.
> modprobe: can't open 'modules.dep': No such file or directory
> iptables v1.4.9: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
> Perhaps iptables or your kernel needs to be upgraded.
> Starting DHCP server: .
> Fri Apr 8 12:29:00 UTC 2011
> Configuring update-modules.
> Configuring kernel-image-2.6.37.3.
> Configuring kernel-module-nf-conntrack.
> Configuring kernel-module-x-tables.
> Configuring kernel-module-ip-tables.
> Configuring kernel-module-nf-defrag-ipv4.
> Configuring kernel-module-nf-conntrack-ipv4.
> Configuring kernel-module-iptable-mangle.
> Configuring kernel-module-xt-state.
> Configuring kernel-module-nf-nat.
> Configuring kernel-module-nf-conntrack-tftp.
> Configuring kernel-module-nf-nat-tftp.
> Configuring kernel-module-ipt-masquerade.
> Configuring kernel-module-iptable-nat.
> Configuring kernel-module-iptable-filter.
> Configuring netkit-tftpd.
> Configuring kernel-module-xt-tcpudp.
>
> So, what decides when these 'configuring' steps run?

FAOD, these are my init.S steps:
   /etc/rcS.d:
    S02banner.sh -> ../init.d/banner.sh
    S03sysfs.sh -> ../init.d/sysfs.sh
    S04udev -> ../init.d/udev
    S10checkroot.sh -> ../init.d/checkroot.sh
    S20modutils.sh -> ../init.d/modutils.sh
    S35mountall.sh -> ../init.d/mountall.sh
    S36udev-cache -> ../init.d/udev-cache
    S37populate-volatile.sh -> ../init.d/populate-volatile.sh
    S38devpts.sh -> ../init.d/devpts.sh
    S39hostname.sh -> ../init.d/hostname.sh
    S40networking -> ../init.d/networking
    S41nat_setup -> ../init.d/nat_setup
    S45mountnfs.sh -> ../init.d/mountnfs.sh
    S50dhcp-server -> ../init.d/dhcp-server
    S55bootmisc.sh -> ../init.d/bootmisc.sh


-- 
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------


  reply	other threads:[~2011-04-08 13:29 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-04-08 13:20 Early image startup Gary Thomas
2011-04-08 13:29 ` Gary Thomas [this message]
     [not found] ` <8B7010C5-9902-4372-BF78-252D85C4BF46@dominion.thruhere.net>
     [not found]   ` <1302270609.22904.128.camel@rex>
     [not found]     ` <4D9F1540.6020902@mlbassoc.com>
     [not found]       ` <4D9F169D.9020502@mlbassoc.com>
     [not found]         ` <4D9F1909.1060403@mlbassoc.com>
     [not found]           ` <3598D5EC-C050-461B-B540-5B20CB79B936@windriver.com>
2011-04-08 17:03             ` [OE-core] " Gary Thomas

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4D9F0DBB.8070608@mlbassoc.com \
    --to=gary@mlbassoc.com \
    --cc=poky@yoctoproject.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox