qemu-devel.nongnu.org archive mirror
 help / color / mirror / Atom feed
From: Zachary Amsden <zamsden@redhat.com>
To: qemu-devel@nongnu.org
Cc: zamsden@redhat.com
Subject: [Qemu-devel] [PATCH 09/14] Further transformation: use common vga_init() which allows either I/O port or memory mapped based control.
Date: Thu, 30 Jul 2009 00:15:07 -1000	[thread overview]
Message-ID: <1248948912-7877-10-git-send-email-zamsden@redhat.com> (raw)
In-Reply-To: <1248948912-7877-9-git-send-email-zamsden@redhat.com>

Signed-off-by: Zachary Amsden <zamsden@redhat.com>
---
 hw/vga.c        |   40 +++++++++++++---------------------------
 hw/vga_int.h    |    3 ++-
 hw/vmware_vga.c |    2 +-
 3 files changed, 16 insertions(+), 29 deletions(-)

diff --git a/hw/vga.c b/hw/vga.c
index 52fb1c4..907cdb7 100644
--- a/hw/vga.c
+++ b/hw/vga.c
@@ -2341,24 +2341,6 @@ static void vga_ioport_init(VGAState *s)
 #endif /* CONFIG_BOCHS_VBE */
 }
 
-/* used by both ISA and PCI */
-void vga_init(VGAState *s)
-{
-    int vga_io_memory;
-
-    qemu_register_reset(vga_reset, 0, s);
-    register_savevm("vga", 0, 2, vga_save, vga_load, s);
-
-    s->bank_offset = 0;
-
-    vga_ioport_init(s);
-
-    vga_io_memory = cpu_register_io_memory(vga_mem_read, vga_mem_write, s);
-    cpu_register_physical_memory(isa_mem_base + 0x000a0000, 0x20000,
-                                 vga_io_memory);
-    qemu_register_coalesced_mmio(isa_mem_base + 0x000a0000, 0x20000);
-}
-
 /* Memory mapped interface */
 static uint32_t vga_mm_readb (void *opaque, target_phys_addr_t addr)
 {
@@ -2417,8 +2399,8 @@ static CPUWriteMemoryFunc *vga_mm_write_ctrl[] = {
     &vga_mm_writel,
 };
 
-static void vga_mm_init(VGAState *s, target_phys_addr_t vram_base,
-                        target_phys_addr_t ctrl_base, int it_shift)
+void vga_init(VGAState *s, target_phys_addr_t vram_base,
+              target_phys_addr_t ctrl_base, int it_shift)
 {
     int s_ioport_ctrl, vga_io_memory;
 
@@ -2426,13 +2408,17 @@ static void vga_mm_init(VGAState *s, target_phys_addr_t vram_base,
     register_savevm("vga", 0, 2, vga_save, vga_load, s);
 
     s->bank_offset = 0;
-
     s->it_shift = it_shift;
-    s_ioport_ctrl = cpu_register_io_memory(vga_mm_read_ctrl, vga_mm_write_ctrl, s);
 
-    vga_io_memory = cpu_register_io_memory(vga_mem_read, vga_mem_write, s);
+    /* Pass ctrl_base to setup memory mapped I/O control */
+    if (ctrl_base) {
+        s_ioport_ctrl = cpu_register_io_memory(vga_mm_read_ctrl, vga_mm_write_ctrl, s);
+        cpu_register_physical_memory(ctrl_base, 0x100000, s_ioport_ctrl);
+    } else {
+        vga_ioport_init(s);
+    }
 
-    cpu_register_physical_memory(ctrl_base, 0x100000, s_ioport_ctrl);
+    vga_io_memory = cpu_register_io_memory(vga_mem_read, vga_mem_write, s);
     cpu_register_physical_memory(vram_base, 0x20000, vga_io_memory);
     qemu_register_coalesced_mmio(vram_base, 0x20000);
 }
@@ -2444,7 +2430,7 @@ int isa_vga_init(void)
     s = qemu_mallocz(sizeof(VGAState));
 
     vga_common_init(s, VGA_RAM_SIZE);
-    vga_init(s);
+    vga_init(s, isa_mem_base + 0xa0000, 0, -1);
 
     s->ds = graphic_console_init(s->update, s->invalidate,
                                  s->screen_dump, s->text_update, s);
@@ -2465,7 +2451,7 @@ int isa_vga_mm_init(target_phys_addr_t vram_base,
     s = qemu_mallocz(sizeof(VGAState));
 
     vga_common_init(s, VGA_RAM_SIZE);
-    vga_mm_init(s, vram_base, ctrl_base, it_shift);
+    vga_init(s, vram_base, ctrl_base, it_shift);
 
     s->ds = graphic_console_init(s->update, s->invalidate,
                                  s->screen_dump, s->text_update, s);
@@ -2504,7 +2490,7 @@ int pci_vga_init(PCIBus *bus,
     s = &d->vga_state;
 
     vga_common_init(s, VGA_RAM_SIZE);
-    vga_init(s);
+    vga_init(s, isa_mem_base + 0xa0000, 0, -1);
 
     s->ds = graphic_console_init(s->update, s->invalidate,
                                  s->screen_dump, s->text_update, s);
diff --git a/hw/vga_int.h b/hw/vga_int.h
index 83b69ef..f072663 100644
--- a/hw/vga_int.h
+++ b/hw/vga_int.h
@@ -190,7 +190,8 @@ static inline int c6_to_8(int v)
 }
 
 void vga_common_init(VGAState *s, int vga_ram_size);
-void vga_init(VGAState *s);
+void vga_init(VGAState *s, target_phys_addr_t vram_base,
+                     target_phys_addr_t ctrl_base, int it_shift);
 void vga_reset(void *s);
 
 void vga_dirty_log_start(VGAState *s);
diff --git a/hw/vmware_vga.c b/hw/vmware_vga.c
index accdac4..d81d263 100644
--- a/hw/vmware_vga.c
+++ b/hw/vmware_vga.c
@@ -1130,7 +1130,7 @@ static void vmsvga_init(struct vmsvga_state_s *s, int vga_ram_size)
 
 #ifdef EMBED_STDVGA
     vga_common_init((VGAState *) s, vga_ram_size);
-    vga_init((VGAState *) s);
+    vga_init((VGAState *) s, isa_mem_base + 0xa0000, 0, -1);
 #else
     s->vram_size = vga_ram_size;
     s->vram_offset = qemu_ram_alloc(vga_ram_size);
-- 
1.6.2.5

  reply	other threads:[~2009-07-30 10:19 UTC|newest]

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-07-30 10:14 [Qemu-devel] Various VGA / VNC fixes and cleanups to prep for multiheaded graphics Zachary Amsden
2009-07-30 10:14 ` [Qemu-devel] [PATCH 01/14] Add a configure switch to enable / disable all user targets. I felt compelled to do it for symmetry, mostly it is useful to disable user targets when you don't want to build them Zachary Amsden
2009-07-30 10:15   ` [Qemu-devel] [PATCH 02/14] Don't segfault when changing VNC password on an SDL display Zachary Amsden
2009-07-30 10:15     ` [Qemu-devel] [PATCH 03/14] When using stdio monitor and VNC display, one can set or clear a VNC password; this should set or turn off VNC authentication as well Zachary Amsden
2009-07-30 10:15       ` [Qemu-devel] [PATCH 04/14] Clean up VGA type selection; far too many variables being used to track one state leads to confusion if new variables are added Zachary Amsden
2009-07-30 10:15         ` [Qemu-devel] [PATCH 05/14] Change cpu_phys mem callback to use [offset, size) bounds instead of [start, end) Zachary Amsden
2009-07-30 10:15           ` [Qemu-devel] [PATCH 06/14] Split VGA ioport init into a helper function Zachary Amsden
2009-07-30 10:15             ` [Qemu-devel] [PATCH 07/14] Code motion; make mm VGA init function more like standard vga init function. Add missing vga_reset hook to vga_mm_init Zachary Amsden
2009-07-30 10:15               ` [Qemu-devel] [PATCH 08/14] Make VGA vram offset passed into vga_mm_init absolute. Since this is a function of the platform, it makes sense to have it be explicitly known in the platform layer rather than hardcoded inside the vga code Zachary Amsden
2009-07-30 10:15                 ` Zachary Amsden [this message]
2009-07-30 10:15                   ` [Qemu-devel] [PATCH 10/14] Stash VGA physical address and use it in KVM callbacks. Stash VGA physical pointer in cirrus vga as well Zachary Amsden
2009-07-30 10:15                     ` [Qemu-devel] [PATCH 11/14] Add some defined constants for VGA offsets Zachary Amsden
2009-07-30 10:15                       ` [Qemu-devel] [PATCH 12/14] Add a PCI BAR for the VGA ROM which is mapped into cirrus_vga. This makes the cirrus device complete under some X servers which require the V_BIOS mapping Zachary Amsden
2009-07-30 10:15                         ` [Qemu-devel] [PATCH 13/14] Allow cirrus VGA to be initialized multiple times; only the first init takes the ISA memory region and hardware I/O ports Zachary Amsden
2009-07-30 10:15                           ` [Qemu-devel] [PATCH 14/14] Atrocious and horrendous patch to demonstrate multiple SDL displays. The multiple SDL displays can be seen on one console, using ctrl-alt-1/2 to switch between them Zachary Amsden
2009-07-30 11:03               ` [Qemu-devel] Re: [PATCH 07/14] Code motion; make mm VGA init function more like standard vga init function. Add missing vga_reset hook to vga_mm_init Jan Kiszka
2009-07-30 11:03           ` [Qemu-devel] Re: [PATCH 05/14] Change cpu_phys mem callback to use [offset, size) bounds instead of [start, end) Jan Kiszka
2009-08-10 19:42           ` [Qemu-devel] " Anthony Liguori
2009-07-30 10:34 ` [Qemu-devel] Various VGA / VNC fixes and cleanups to prep for multiheaded graphics Daniel P. Berrange
2009-07-30 10:35   ` Zachary Amsden
2009-07-30 11:33     ` Paul Brook

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1248948912-7877-10-git-send-email-zamsden@redhat.com \
    --to=zamsden@redhat.com \
    --cc=qemu-devel@nongnu.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).