[Qemu-devel] [PATCH 19/23] usb: update documentation

[Gerd Hoffmann <kraxel@redhat.com>]

Add a paragraph on companion controller mode and a
configuration file which sets it all up for you.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 docs/ich9-ehci-uhci.cfg |   37 +++++++++++++++++++++++++++++++++++++
 docs/usb2.txt           |   33 ++++++++++++++++++++++++++++-----
 2 files changed, 65 insertions(+), 5 deletions(-)
 create mode 100644 docs/ich9-ehci-uhci.cfg

diff --git a/docs/ich9-ehci-uhci.cfg b/docs/ich9-ehci-uhci.cfg
new file mode 100644
index 0000000..a0e9b96
--- /dev/null
+++ b/docs/ich9-ehci-uhci.cfg
@@ -0,0 +1,37 @@
+###########################################################################
+#
+# You can pass this file directly to qemu using the -readconfig
+# command line switch.
+#
+# This config file creates a EHCI adapter with companion UHCI
+# controllers as multifunction device in PCI slot "1d".
+#
+# Specify "bus=ehci.0" when creating usb devices to hook them up
+# there.
+#
+
+[device "ehci"]
+  driver = "ich9-usb-ehci1"
+  addr = "1d.7"
+  multifunction = "on"
+
+[device "uhci-1"]
+  driver = "ich9-usb-uhci1"
+  addr = "1d.0"
+  multifunction = "on"
+  masterbus = "ehci.0"
+  firstport = "0"
+
+[device "uhci-2"]
+  driver = "ich9-usb-uhci2"
+  addr = "1d.1"
+  multifunction = "on"
+  masterbus = "ehci.0"
+  firstport = "2"
+
+[device "uhci-3"]
+  driver = "ich9-usb-uhci3"
+  addr = "1d.2"
+  multifunction = "on"
+  masterbus = "ehci.0"
+  firstport = "4"
diff --git a/docs/usb2.txt b/docs/usb2.txt
index 5950c71..228aa33 100644
--- a/docs/usb2.txt
+++ b/docs/usb2.txt
@@ -2,11 +2,13 @@
 USB 2.0 Quick Start
 ===================
 
-The QEMU EHCI Adapter does *not* support companion controllers.  That
-implies there are two completely separate USB busses: One USB 1.1 bus
-driven by the UHCI controller and one USB 2.0 bus driven by the EHCI
-controller.  Devices must be attached to the correct controller
-manually.
+The QEMU EHCI Adapter can be used with and without companion
+controllers.  See below for the companion controller mode.
+
+When not running in companion controller mode there are two completely
+separate USB busses: One USB 1.1 bus driven by the UHCI controller and
+one USB 2.0 bus driven by the EHCI controller.  Devices must be
+attached to the correct controller manually.
 
 The '-usb' switch will make qemu create the UHCI controller as part of
 the PIIX3 chipset.  The USB 1.1 bus will carry the name "usb.0".
@@ -32,6 +34,27 @@ This attaches a usb tablet to the UHCI adapter and a usb mass storage
 device to the EHCI adapter.
 
 
+Companion controller support
+----------------------------
+
+Companion controller support has been added recently.  The operational
+model described above with two completely separate busses still works
+fine.  Additionally the UHCI and OHCI controllers got the ability to
+attach to a usb bus created by EHCI as companion controllers.  This is
+done by specifying the masterbus and firstport properties.  masterbus
+specifies the bus name the controller should attach to.  firstport
+specifies the first port the controller should attach to, which is
+needed as usually one ehci controller with six ports has three uhci
+companion controllers with two ports each.
+
+There is a config file in docs which will do all this for you, just
+try ...
+
+    qemu -readconfig docs/ich9-ehci-uhci.cfg
+
+... then use "bus=ehci.0" to assign your usb devices to that bus.
+
+
 More USB tips & tricks
 ======================
 
-- 
1.7.1