From: "Hervé Poussineau" <hpoussin@reactos.org>
To: qemu-devel@nongnu.org
Cc: "Kevin Wolf" <kwolf@redhat.com>,
"Hervé Poussineau" <hpoussin@reactos.org>
Subject: [Qemu-devel] [PATCH v4 05/11] fdc: add CCR (Configuration Control Register) write register
Date: Mon, 6 Feb 2012 22:29:06 +0100 [thread overview]
Message-ID: <1328563752-3976-6-git-send-email-hpoussin@reactos.org> (raw)
In-Reply-To: <1328563752-3976-1-git-send-email-hpoussin@reactos.org>
DIR and CCR registers share the same address ; DIR is read-only
while CCR is write-only
CCR register is used to change media transfer rate, which will be
checked in following changes.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
---
hw/fdc.c | 22 ++++++++++++++++++++++
1 files changed, 22 insertions(+), 0 deletions(-)
diff --git a/hw/fdc.c b/hw/fdc.c
index 060ca84..2bad97b 100644
--- a/hw/fdc.c
+++ b/hw/fdc.c
@@ -224,6 +224,7 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value);
static uint32_t fdctrl_read_data(FDCtrl *fdctrl);
static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value);
static uint32_t fdctrl_read_dir(FDCtrl *fdctrl);
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value);
enum {
FD_DIR_WRITE = 0,
@@ -248,6 +249,7 @@ enum {
FD_REG_DSR = 0x04,
FD_REG_FIFO = 0x05,
FD_REG_DIR = 0x07,
+ FD_REG_CCR = 0x07,
};
enum {
@@ -491,6 +493,9 @@ static void fdctrl_write (void *opaque, uint32_t reg, uint32_t value)
case FD_REG_FIFO:
fdctrl_write_data(fdctrl, value);
break;
+ case FD_REG_CCR:
+ fdctrl_write_ccr(fdctrl, value);
+ break;
default:
break;
}
@@ -881,6 +886,23 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value)
fdctrl->dsr = value;
}
+/* Configuration control register: 0x07 (write) */
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value)
+{
+ /* Reset mode */
+ if (!(fdctrl->dor & FD_DOR_nRESET)) {
+ FLOPPY_DPRINTF("Floppy controller in RESET state !\n");
+ return;
+ }
+ FLOPPY_DPRINTF("configuration control register set to 0x%02x\n", value);
+
+ /* Only the rate selection bits used in AT mode, and we
+ * store those in the DSR.
+ */
+ fdctrl->dsr = (fdctrl->dsr & ~FD_DSR_DRATEMASK) |
+ (value & FD_DSR_DRATEMASK);
+}
+
static int fdctrl_media_changed(FDrive *drv)
{
int ret;
--
1.7.8.3
next prev parent reply other threads:[~2012-02-06 21:30 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-06 21:29 [Qemu-devel] [PATCH v4 00/11] Misc fixes for floppy emulation Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 01/11] fdc: take side count into account Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 02/11] fdc: set busy bit when starting a command Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 03/11] fdc: most control commands do not generate interrupts Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 04/11] fdc: handle read-only floppies (abort early on write commands) Hervé Poussineau
2012-02-06 21:29 ` Hervé Poussineau [this message]
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 06/11] block: add a transfer rate for floppy types Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 07/11] pc: add 1.1 machine type Hervé Poussineau
2012-02-14 15:11 ` Kevin Wolf
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 08/11] fdc: add a 'check media rate' property. Not used yet Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 09/11] fdc: check if media rate is correct before doing any transfer Hervé Poussineau
2012-02-14 15:16 ` Kevin Wolf
2012-02-14 15:28 ` Paolo Bonzini
2012-02-14 15:34 ` Kevin Wolf
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 10/11] fdc: fix seek command, which shouldn't check tracks Hervé Poussineau
2012-02-06 21:29 ` [Qemu-devel] [PATCH v4 11/11] fdc: DIR (Digital Input Register) should return status of current drive Hervé Poussineau
2012-02-14 12:31 ` [Qemu-devel] [PATCH v4 00/11] Misc fixes for floppy emulation Hervé Poussineau
2012-02-14 15:27 ` Kevin Wolf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1328563752-3976-6-git-send-email-hpoussin@reactos.org \
--to=hpoussin@reactos.org \
--cc=kwolf@redhat.com \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).