* [Qemu-devel] [PATCH v11 01/26] target-arm: extend async excp masking
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 02/26] target-arm: add async excp target_el function Greg Bellows
` (25 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
This patch extends arm_excp_unmasked() to use lookup tables for determining
whether IRQ and FIQ exceptions are masked. The lookup tables are based on the
ARMv8 and ARMv7 specification physical interrupt masking tables.
If EL3 is using AArch64 IRQ/FIQ masking is ignored in all exception levels
other than EL3 if SCR.{FIQ|IRQ} is set to 1 (routed to EL3).
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v10 -> v11
- Fix arm_excp_unmasked el3_is_aa64 logic so it is clearer.
v8 -> v9
- Undo the use of tables for exception masking and instead go with simplified
logic based on the target EL lookup.
- Remove the masking tables
v7 -> v8
- Add IRQ and FIQ exeception masking lookup tables.
- Rewrite patch to use lookup tables for determining whether an excpetion is
masked or not.
v5 -> v6
- Globally change Aarch# to AArch#
- Fixed comment termination
v4 -> v5
- Merge with v4 patch 10
---
target-arm/cpu.h | 66 ++++++++++++++++++++++++++++++++++++++++++++------------
1 file changed, 52 insertions(+), 14 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 7f80090..810cc0b 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -1247,27 +1247,50 @@ static inline bool arm_excp_unmasked(CPUState *cs, unsigned int excp_idx)
CPUARMState *env = cs->env_ptr;
unsigned int cur_el = arm_current_el(env);
unsigned int target_el = arm_excp_target_el(cs, excp_idx);
- /* FIXME: Use actual secure state. */
- bool secure = false;
- /* If in EL1/0, Physical IRQ routing to EL2 only happens from NS state. */
- bool irq_can_hyp = !secure && cur_el < 2 && target_el == 2;
-
- /* Don't take exceptions if they target a lower EL. */
+ bool secure = arm_is_secure(env);
+ uint32_t scr;
+ uint32_t hcr;
+ bool pstate_unmasked;
+ int8_t unmasked = 0;
+
+ /* Don't take exceptions if they target a lower EL.
+ * This check should catch any exceptions that would not be taken but left
+ * pending.
+ */
if (cur_el > target_el) {
return false;
}
switch (excp_idx) {
case EXCP_FIQ:
- if (irq_can_hyp && (env->cp15.hcr_el2 & HCR_FMO)) {
- return true;
- }
- return !(env->daif & PSTATE_F);
+ /* If FIQs are routed to EL3 or EL2 then there are cases where we
+ * override the CPSR.F in determining if the exception is masked or
+ * not. If neither of these are set then we fall back to the CPSR.F
+ * setting otherwise we further assess the state below.
+ */
+ hcr = (env->cp15.hcr_el2 & HCR_FMO);
+ scr = (env->cp15.scr_el3 & SCR_FIQ);
+
+ /* When EL3 is 32-bit, the SCR.FW bit controls whether the CPSR.F bit
+ * masks FIQ interrupts when taken in non-secure state. If SCR.FW is
+ * set then FIQs can be masked by CPSR.F when non-secure but only
+ * when FIQs are only routed to EL3.
+ */
+ scr &= !((env->cp15.scr_el3 & SCR_FW) && !hcr);
+ pstate_unmasked = !(env->daif & PSTATE_F);
+ break;
+
case EXCP_IRQ:
- if (irq_can_hyp && (env->cp15.hcr_el2 & HCR_IMO)) {
- return true;
- }
- return !(env->daif & PSTATE_I);
+ /* When EL3 execution state is 32-bit, if HCR.IMO is set then we may
+ * override the CPSR.I masking when in non-secure state. The SCR.IRQ
+ * setting has already been taken into consideration when setting the
+ * target EL, so it does not have a further affect here.
+ */
+ hcr = (env->cp15.hcr_el2 & HCR_IMO);
+ scr = false;
+ pstate_unmasked = !(env->daif & PSTATE_I);
+ break;
+
case EXCP_VFIQ:
if (secure || !(env->cp15.hcr_el2 & HCR_FMO)) {
/* VFIQs are only taken when hypervized and non-secure. */
@@ -1283,6 +1306,21 @@ static inline bool arm_excp_unmasked(CPUState *cs, unsigned int excp_idx)
default:
g_assert_not_reached();
}
+
+ /* Use the target EL, current execution state and SCR/HCR settings to
+ * determine whether the corresponding CPSR bit is used to mask the
+ * interrupt.
+ */
+ if ((target_el > cur_el) && (target_el != 1)) {
+ if (arm_el_is_aa64(env, 3) || ((scr || hcr) && (!secure))) {
+ unmasked = 1;
+ }
+ }
+
+ /* The PSTATE bits only mask the interrupt if we have not overriden the
+ * ability above.
+ */
+ return unmasked || pstate_unmasked;
}
static inline CPUARMState *cpu_init(const char *cpu_model)
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 02/26] target-arm: add async excp target_el function
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 01/26] target-arm: extend async excp masking Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 03/26] target-arm: add banked register accessors Greg Bellows
` (24 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
Adds a dedicated function and a lookup table for determining the target
exception level of IRQ and FIQ exceptions. The lookup table is taken from the
ARMv7 and ARMv8 specification exception routing tables.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Fixed target_el_table in correct 32-bit secure values
- Expanded comment on target_el_table untaken exception handling
- Fixed minor issues
v7 -> v8
- Added target EL lookup table
- Rework arm_phys_excp_target_el to use an EL lookup table rather than
conditionals.
v5 -> v6
- Removed unneeded arm_phys_excp_target_el() function prototype.
- Removed unneeded arm_phys_excp_target_el() USER_ONLY function.
- Fixed up arm_phys_excp_target_el() function definition to be static.
- Globally replace Aarch# with AArch#
v4 -> v5
- Simplify target EL function including removal of mode which was unused
- Merged with patch that plugs in the use of the function
v3 -> v4
- Fixed arm_phys_excp_target_el() 0/0/0 case to return excp_mode when EL<2
rather than ABORT.
---
target-arm/helper.c | 116 +++++++++++++++++++++++++++++++++++++++++++---------
1 file changed, 97 insertions(+), 19 deletions(-)
diff --git a/target-arm/helper.c b/target-arm/helper.c
index c47487a..a48ebae 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -3761,6 +3761,101 @@ void switch_mode(CPUARMState *env, int mode)
env->spsr = env->banked_spsr[i];
}
+/* Physical Interrupt Target EL Lookup Table
+ *
+ * [ From ARM ARM section G1.13.4 (Table G1-15) ]
+ *
+ * The below multi-dimensional table is used for looking up the target
+ * exception level given numerous condition criteria. Specifically, the
+ * target EL is based on SCR and HCR routing controls as well as the
+ * currently executing EL and secure state.
+ *
+ * Dimensions:
+ * target_el_table[2][2][2][2][2][4]
+ * | | | | | +--- Current EL
+ * | | | | +------ Non-secure(0)/Secure(1)
+ * | | | +--------- HCR mask override
+ * | | +------------ SCR exec state control
+ * | +--------------- SCR mask override
+ * +------------------ 32-bit(0)/64-bit(1) EL3
+ *
+ * The table values are as such:
+ * 0-3 = EL0-EL3
+ * -1 = Cannot occur
+ *
+ * The ARM ARM target EL table includes entries indicating that an "exception
+ * is not taken". The two cases where this is applicable are:
+ * 1) An exception is taken from EL3 but the SCR does not have the exception
+ * routed to EL3.
+ * 2) An exception is taken from EL2 but the HCR does not have the exception
+ * routed to EL2.
+ * In these two cases, the below table contain a target of EL1. This value is
+ * returned as it is expected that the consumer of the table data will check
+ * for "target EL >= current EL" to ensure the exception is not taken.
+ *
+ * SCR HCR
+ * 64 EA AMO From
+ * BIT IRQ IMO Non-secure Secure
+ * EL3 FIQ RW FMO EL0 EL1 EL2 EL3 EL0 EL1 EL2 EL3
+ */
+const int8_t target_el_table[2][2][2][2][2][4] = {
+ {{{{/* 0 0 0 0 */{ 1, 1, 2, -1 },{ 3, -1, -1, 3 },},
+ {/* 0 0 0 1 */{ 2, 2, 2, -1 },{ 3, -1, -1, 3 },},},
+ {{/* 0 0 1 0 */{ 1, 1, 2, -1 },{ 3, -1, -1, 3 },},
+ {/* 0 0 1 1 */{ 2, 2, 2, -1 },{ 3, -1, -1, 3 },},},},
+ {{{/* 0 1 0 0 */{ 3, 3, 3, -1 },{ 3, -1, -1, 3 },},
+ {/* 0 1 0 1 */{ 3, 3, 3, -1 },{ 3, -1, -1, 3 },},},
+ {{/* 0 1 1 0 */{ 3, 3, 3, -1 },{ 3, -1, -1, 3 },},
+ {/* 0 1 1 1 */{ 3, 3, 3, -1 },{ 3, -1, -1, 3 },},},},},
+ {{{{/* 1 0 0 0 */{ 1, 1, 2, -1 },{ 1, 1, -1, 1 },},
+ {/* 1 0 0 1 */{ 2, 2, 2, -1 },{ 1, 1, -1, 1 },},},
+ {{/* 1 0 1 0 */{ 1, 1, 1, -1 },{ 1, 1, -1, 1 },},
+ {/* 1 0 1 1 */{ 2, 2, 2, -1 },{ 1, 1, -1, 1 },},},},
+ {{{/* 1 1 0 0 */{ 3, 3, 3, -1 },{ 3, 3, -1, 3 },},
+ {/* 1 1 0 1 */{ 3, 3, 3, -1 },{ 3, 3, -1, 3 },},},
+ {{/* 1 1 1 0 */{ 3, 3, 3, -1 },{ 3, 3, -1, 3 },},
+ {/* 1 1 1 1 */{ 3, 3, 3, -1 },{ 3, 3, -1, 3 },},},},},
+};
+
+/*
+ * Determine the target EL for physical exceptions
+ */
+static inline uint32_t arm_phys_excp_target_el(CPUState *cs, uint32_t excp_idx,
+ uint32_t cur_el, bool secure)
+{
+ CPUARMState *env = cs->env_ptr;
+ int rw = ((env->cp15.scr_el3 & SCR_RW) == SCR_RW);
+ int scr;
+ int hcr;
+ int target_el;
+ int is64 = arm_el_is_aa64(env, 3);
+
+ switch (excp_idx) {
+ case EXCP_IRQ:
+ scr = ((env->cp15.scr_el3 & SCR_IRQ) == SCR_IRQ);
+ hcr = ((env->cp15.hcr_el2 & HCR_IMO) == HCR_IMO);
+ break;
+ case EXCP_FIQ:
+ scr = ((env->cp15.scr_el3 & SCR_FIQ) == SCR_FIQ);
+ hcr = ((env->cp15.hcr_el2 & HCR_FMO) == HCR_FMO);
+ break;
+ default:
+ scr = ((env->cp15.scr_el3 & SCR_EA) == SCR_EA);
+ hcr = ((env->cp15.hcr_el2 & HCR_AMO) == HCR_AMO);
+ break;
+ };
+
+ /* If HCR.TGE is set then HCR is treated as being 1 */
+ hcr |= ((env->cp15.hcr_el2 & HCR_TGE) == HCR_TGE);
+
+ /* Perform a table-lookup for the target EL given the current state */
+ target_el = target_el_table[is64][scr][rw][hcr][secure][cur_el];
+
+ assert(target_el > 0);
+
+ return target_el;
+}
+
/*
* Determine the target EL for a given exception type.
*/
@@ -3770,13 +3865,7 @@ unsigned int arm_excp_target_el(CPUState *cs, unsigned int excp_idx)
CPUARMState *env = &cpu->env;
unsigned int cur_el = arm_current_el(env);
unsigned int target_el;
- /* FIXME: Use actual secure state. */
- bool secure = false;
-
- if (!env->aarch64) {
- /* TODO: Add EL2 and 3 exception handling for AArch32. */
- return 1;
- }
+ bool secure = arm_is_secure(env);
switch (excp_idx) {
case EXCP_HVC:
@@ -3788,19 +3877,8 @@ unsigned int arm_excp_target_el(CPUState *cs, unsigned int excp_idx)
break;
case EXCP_FIQ:
case EXCP_IRQ:
- {
- const uint64_t hcr_mask = excp_idx == EXCP_FIQ ? HCR_FMO : HCR_IMO;
- const uint32_t scr_mask = excp_idx == EXCP_FIQ ? SCR_FIQ : SCR_IRQ;
-
- target_el = 1;
- if (!secure && (env->cp15.hcr_el2 & hcr_mask)) {
- target_el = 2;
- }
- if (env->cp15.scr_el3 & scr_mask) {
- target_el = 3;
- }
+ target_el = arm_phys_excp_target_el(cs, excp_idx, cur_el, secure);
break;
- }
case EXCP_VIRQ:
case EXCP_VFIQ:
target_el = 1;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 03/26] target-arm: add banked register accessors
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 01/26] target-arm: extend async excp masking Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 02/26] target-arm: add async excp target_el function Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 04/26] target-arm: add non-secure Translation Block flag Greg Bellows
` (23 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
If EL3 is in AArch32 state certain cp registers are banked (secure and
non-secure instance). When reading or writing to coprocessor registers
the following macros can be used.
- A32_BANKED macros are used for choosing the banked register based on provided
input security argument. This macro is used to choose the bank during
translation of MRC/MCR instructions that are dependent on something other
than the current secure state.
- A32_BANKED_CURRENT macros are used for choosing the banked register based on
current secure state. This is NOT to be used for choosing the bank used
during translation as it breaks monitor mode.
If EL3 is operating in AArch64 state coprocessor registers are not
banked anymore. The macros use the non-secure instance (_ns) in this
case, which is architecturally mapped to the AArch64 EL register.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v7 -> v8
- Move use_secure_reg() function to the TBFLAG patch.
v5 -> v6
- Converted macro USE_SECURE_REG() into inlince function use_secure_reg()
- Globally replace Aarch# with AArch#
v4 -> v5
- Cleaned-up macros to try and alleviate misuse. Made A32_BANKED macros take
secure arg indicator rather than relying on USE_SECURE_REG. Incorporated the
A32_BANKED macros into the A32_BANKED_CURRENT. CURRENT is now the only one
that automatically chooses based on current secure state.
---
target-arm/cpu.h | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 810cc0b..1ad5d38 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -817,6 +817,33 @@ static inline bool arm_el_is_aa64(CPUARMState *env, int el)
return arm_feature(env, ARM_FEATURE_AARCH64);
}
+/* Macros for accessing a specified CP register bank */
+#define A32_BANKED_REG_GET(_env, _regname, _secure) \
+ ((_secure) ? (_env)->cp15._regname##_s : (_env)->cp15._regname##_ns)
+
+#define A32_BANKED_REG_SET(_env, _regname, _secure, _val) \
+ do { \
+ if (_secure) { \
+ (_env)->cp15._regname##_s = (_val); \
+ } else { \
+ (_env)->cp15._regname##_ns = (_val); \
+ } \
+ } while (0)
+
+/* Macros for automatically accessing a specific CP register bank depending on
+ * the current secure state of the system. These macros are not intended for
+ * supporting instruction translation reads/writes as these are dependent
+ * solely on the SCR.NS bit and not the mode.
+ */
+#define A32_BANKED_CURRENT_REG_GET(_env, _regname) \
+ A32_BANKED_REG_GET((_env), _regname, \
+ ((!arm_el_is_aa64((_env), 3) && arm_is_secure(_env))))
+
+#define A32_BANKED_CURRENT_REG_SET(_env, _regname, _val) \
+ A32_BANKED_REG_SET((_env), _regname, \
+ ((!arm_el_is_aa64((_env), 3) && arm_is_secure(_env))), \
+ (_val))
+
void arm_cpu_list(FILE *f, fprintf_function cpu_fprintf);
unsigned int arm_excp_target_el(CPUState *cs, unsigned int excp_idx);
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 04/26] target-arm: add non-secure Translation Block flag
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (2 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 03/26] target-arm: add banked register accessors Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 05/26] target-arm: add CPREG secure state support Greg Bellows
` (22 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Sergey Fedorov <s.fedorov@samsung.com>
This patch is based on idea found in patch at
git://github.com/jowinter/qemu-trustzone.git
f3d955c6c0ed8c46bc0eb10b634201032a651dd2 by
Johannes Winter <johannes.winter@iaik.tugraz.at>.
The TBFLAG captures the SCR NS secure state at the time when a TB is created so
the correct bank is accessed on system register accesses.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v7 -> v8
- Moved and renamed use_secure_reg() to this patch. New name is
access_secure_reg().
- Fixed function comment
v5 -> v6
- Removed 64-bit NS TBFLAG macros as they are not needed
- Added comment on DisasContext ns field
- Replaced use of USE_SECURE_REG with use_secure_reg
v4 -> v5
- Merge changes
- Fixed issue where TB secure state flag was incorrectly being set based on
secure state rather than NS setting. This caused an issue where monitor mode
MRC/MCR accesses were always secure rather than being based on NS bit
setting.
- Added separate 64/32 TB secure state flags
- Unconditionalized the setting of the DC ns bit
- Removed IS_NS macro and replaced with direct usage.
---
target-arm/cpu.h | 27 +++++++++++++++++++++++++++
target-arm/translate.c | 1 +
target-arm/translate.h | 1 +
3 files changed, 29 insertions(+)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 1ad5d38..6881098 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -817,6 +817,22 @@ static inline bool arm_el_is_aa64(CPUARMState *env, int el)
return arm_feature(env, ARM_FEATURE_AARCH64);
}
+/* Function for determing whether guest cp register reads and writes should
+ * access the secure or non-secure bank of a cp register. When EL3 is
+ * operating in AArch32 state, the NS-bit determines whether the secure
+ * instance of a cp register should be used. When EL3 is AArch64 (or if
+ * it doesn't exist at all) then there is no register banking, and all
+ * accesses are to the non-secure version.
+ */
+static inline bool access_secure_reg(CPUARMState *env)
+{
+ bool ret = (arm_feature(env, ARM_FEATURE_EL3) &&
+ !arm_el_is_aa64(env, 3) &&
+ !(env->cp15.scr_el3 & SCR_NS));
+
+ return ret;
+}
+
/* Macros for accessing a specified CP register bank */
#define A32_BANKED_REG_GET(_env, _regname, _secure) \
((_secure) ? (_env)->cp15._regname##_s : (_env)->cp15._regname##_ns)
@@ -1467,6 +1483,12 @@ static inline bool arm_singlestep_active(CPUARMState *env)
*/
#define ARM_TBFLAG_XSCALE_CPAR_SHIFT 20
#define ARM_TBFLAG_XSCALE_CPAR_MASK (3 << ARM_TBFLAG_XSCALE_CPAR_SHIFT)
+/* Indicates whether cp register reads and writes by guest code should access
+ * the secure or nonsecure bank of banked registers; note that this is not
+ * the same thing as the current security state of the processor!
+ */
+#define ARM_TBFLAG_NS_SHIFT 22
+#define ARM_TBFLAG_NS_MASK (1 << ARM_TBFLAG_NS_SHIFT)
/* Bit usage when in AArch64 state */
#define ARM_TBFLAG_AA64_EL_SHIFT 0
@@ -1511,6 +1533,8 @@ static inline bool arm_singlestep_active(CPUARMState *env)
(((F) & ARM_TBFLAG_AA64_SS_ACTIVE_MASK) >> ARM_TBFLAG_AA64_SS_ACTIVE_SHIFT)
#define ARM_TBFLAG_AA64_PSTATE_SS(F) \
(((F) & ARM_TBFLAG_AA64_PSTATE_SS_MASK) >> ARM_TBFLAG_AA64_PSTATE_SS_SHIFT)
+#define ARM_TBFLAG_NS(F) \
+ (((F) & ARM_TBFLAG_NS_MASK) >> ARM_TBFLAG_NS_SHIFT)
static inline void cpu_get_tb_cpu_state(CPUARMState *env, target_ulong *pc,
target_ulong *cs_base, int *flags)
@@ -1560,6 +1584,9 @@ static inline void cpu_get_tb_cpu_state(CPUARMState *env, target_ulong *pc,
if (privmode) {
*flags |= ARM_TBFLAG_PRIV_MASK;
}
+ if (!(access_secure_reg(env))) {
+ *flags |= ARM_TBFLAG_NS_MASK;
+ }
if (env->vfp.xregs[ARM_VFP_FPEXC] & (1 << 30)
|| arm_el_is_aa64(env, 1)) {
*flags |= ARM_TBFLAG_VFPEN_MASK;
diff --git a/target-arm/translate.c b/target-arm/translate.c
index af51568..17c459a 100644
--- a/target-arm/translate.c
+++ b/target-arm/translate.c
@@ -11031,6 +11031,7 @@ static inline void gen_intermediate_code_internal(ARMCPU *cpu,
#if !defined(CONFIG_USER_ONLY)
dc->user = (ARM_TBFLAG_PRIV(tb->flags) == 0);
#endif
+ dc->ns = ARM_TBFLAG_NS(tb->flags);
dc->cpacr_fpen = ARM_TBFLAG_CPACR_FPEN(tb->flags);
dc->vfp_enabled = ARM_TBFLAG_VFPEN(tb->flags);
dc->vec_len = ARM_TBFLAG_VECLEN(tb->flags);
diff --git a/target-arm/translate.h b/target-arm/translate.h
index 41a9071..f6ee789 100644
--- a/target-arm/translate.h
+++ b/target-arm/translate.h
@@ -20,6 +20,7 @@ typedef struct DisasContext {
#if !defined(CONFIG_USER_ONLY)
int user;
#endif
+ bool ns; /* Use non-secure CPREG bank on access */
bool cpacr_fpen; /* FP enabled via CPACR.FPEN */
bool vfp_enabled; /* FP enabled via FPSCR.EN */
int vec_len;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 05/26] target-arm: add CPREG secure state support
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (3 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 04/26] target-arm: add non-secure Translation Block flag Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash Greg Bellows
` (21 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Prepare ARMCPRegInfo to support specifying two fieldoffsets per
register definition. This will allow us to keep one register
definition for banked registers (different offsets for secure/
non-secure world).
Also added secure state tracking field and flags. This allows for
identification of the register info secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Removed ARM_CP_SECSTATE_TEST macro
- Replaced dropped comment
v7 -> v8
- Break up the fieldoffset union to avoid need for sometimes overwriting one
bank when updating fieldoffset. This also removes the need for the #define
short-cut introduced in v7.
v6 -> v7
- Add naming for fieldoffset fields and macros for accessing. This was needed
to overcome issues with the GCC-4.4 compiler.
v5 -> v6
- Separate out secure CPREG flags
- Add convenience macro for testing flags
- Removed extraneous newline
- Move add_cpreg_to_hashtable() functionality to a later commit for which it is
dependent on.
- Added comment explaining fieldoffset padding
v4 -> v5
- Added ARM CP register secure and non-secure bank flags
- Added setting of secure and non-secure flags furing registration
---
target-arm/cpu.h | 36 ++++++++++++++++++++++++++++++++++--
1 file changed, 34 insertions(+), 2 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 6881098..dd7d229 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -993,6 +993,21 @@ enum {
ARM_CP_STATE_BOTH = 2,
};
+/* ARM CP register secure state flags. These flags identify security state
+ * attributes for a given CP register entry.
+ * The existence of both or neither secure and non-secure flags indicates that
+ * the register has both a secure and non-secure hash entry. A single one of
+ * these flags causes the register to only be hashed for the specified
+ * security state.
+ * Although definitions may have any combination of the S/NS bits, each
+ * registered entry will only have one to identify whether the entry is secure
+ * or non-secure.
+ */
+enum {
+ ARM_CP_SECSTATE_S = (1 << 0), /* bit[0]: Secure state register */
+ ARM_CP_SECSTATE_NS = (1 << 1), /* bit[1]: Non-secure state register */
+};
+
/* Return true if cptype is a valid type field. This is used to try to
* catch errors where the sentinel has been accidentally left off the end
* of a list of registers.
@@ -1127,6 +1142,8 @@ struct ARMCPRegInfo {
int type;
/* Access rights: PL*_[RW] */
int access;
+ /* Security state: ARM_CP_SECSTATE_* bits/values */
+ int secure;
/* The opaque pointer passed to define_arm_cp_regs_with_opaque() when
* this register was defined: can be used to hand data through to the
* register read/write functions, since they are passed the ARMCPRegInfo*.
@@ -1136,12 +1153,27 @@ struct ARMCPRegInfo {
* fieldoffset is non-zero, the reset value of the register.
*/
uint64_t resetvalue;
- /* Offset of the field in CPUARMState for this register. This is not
- * needed if either:
+ /* Offset of the field in CPUARMState for this register.
+ *
+ * This is not needed if either:
* 1. type is ARM_CP_CONST or one of the ARM_CP_SPECIALs
* 2. both readfn and writefn are specified
*/
ptrdiff_t fieldoffset; /* offsetof(CPUARMState, field) */
+
+ /* Offsets of the secure and non-secure fields in CPUARMState for the
+ * register if it is banked. These fields are only used during the static
+ * registration of a register. During hashing the bank associated
+ * with a given security state is copied to fieldoffset which is used from
+ * there on out.
+ *
+ * It is expected that register definitions use either fieldoffset or
+ * bank_fieldoffsets in the definition but not both. It is also expected
+ * that both bank offsets are set when defining a banked register. This
+ * use indicates that a register is banked.
+ */
+ ptrdiff_t bank_fieldoffsets[2];
+
/* Function for making any access checks for this register in addition to
* those specified by the 'access' permissions bits. If NULL, no extra
* checks required. The access check is performed at runtime, not at
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (4 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 05/26] target-arm: add CPREG secure state support Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-12-09 18:43 ` Peter Maydell
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 07/26] target-arm: insert AArch32 cpregs twice into hashtable Greg Bellows
` (20 subsequent siblings)
26 siblings, 1 reply; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
Added additional NS-bit to CPREG hash encoding. Updated hash lookup
locations to specify hash bit currently set to non-secure.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Fixed CP_REG_NS_MASK
- Changed ENCODE_CP_REG argument order so ns follows is64
- Replaced use of CP_REG_NS_MASK with CP_REG_NS_SHIFT
- Changed add_cpreg_to_hashtable argument order so ns follows is64
- Replaced use of SCR_NS with ARM_CP_SECSTATE_NS on registration
- Undid global replace of Aarch# with AArch# in translate.c
v5 -> v6
- Globally replace Aarch# with AArch#
---
target-arm/cpu.h | 25 ++++++++++++++++++++-----
target-arm/helper.c | 7 ++++---
target-arm/translate.c | 14 +++++++++-----
3 files changed, 33 insertions(+), 13 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index dd7d229..532f698 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -879,6 +879,7 @@ void armv7m_nvic_complete_irq(void *opaque, int irq);
* Crn, Crm, opc1, opc2 fields
* 32 or 64 bit register (ie is it accessed via MRC/MCR
* or via MRRC/MCRR?)
+ * non-secure/secure bank (AArch32 only)
* We allow 4 bits for opc1 because MRRC/MCRR have a 4 bit field.
* (In this case crn and opc2 should be zero.)
* For AArch64, there is no 32/64 bit size distinction;
@@ -896,9 +897,16 @@ void armv7m_nvic_complete_irq(void *opaque, int irq);
#define CP_REG_AA64_SHIFT 28
#define CP_REG_AA64_MASK (1 << CP_REG_AA64_SHIFT)
-#define ENCODE_CP_REG(cp, is64, crn, crm, opc1, opc2) \
- (((cp) << 16) | ((is64) << 15) | ((crn) << 11) | \
- ((crm) << 7) | ((opc1) << 3) | (opc2))
+/* To enable banking of coprocessor registers depending on ns-bit we
+ * add a bit to distinguish between secure and non-secure cpregs in the
+ * hashtable.
+ */
+#define CP_REG_NS_SHIFT 29
+#define CP_REG_NS_MASK (1 << CP_REG_NS_SHIFT)
+
+#define ENCODE_CP_REG(cp, is64, ns, crn, crm, opc1, opc2) \
+ ((ns) << CP_REG_NS_SHIFT | ((cp) << 16) | ((is64) << 15) | \
+ ((crn) << 11) | ((crm) << 7) | ((opc1) << 3) | (opc2))
#define ENCODE_AA64_CP_REG(cp, crn, crm, op0, op1, op2) \
(CP_REG_AA64_MASK | \
@@ -917,8 +925,15 @@ static inline uint32_t kvm_to_cpreg_id(uint64_t kvmid)
uint32_t cpregid = kvmid;
if ((kvmid & CP_REG_ARCH_MASK) == CP_REG_ARM64) {
cpregid |= CP_REG_AA64_MASK;
- } else if ((kvmid & CP_REG_SIZE_MASK) == CP_REG_SIZE_U64) {
- cpregid |= (1 << 15);
+ } else {
+ if ((kvmid & CP_REG_SIZE_MASK) == CP_REG_SIZE_U64) {
+ cpregid |= (1 << 15);
+ }
+
+ /* KVM is always non-secure so add the NS flag on AArch32 register
+ * entries.
+ */
+ cpregid |= 1 << CP_REG_NS_SHIFT;
}
return cpregid;
}
diff --git a/target-arm/helper.c b/target-arm/helper.c
index a48ebae..1aadb79 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -3287,7 +3287,7 @@ CpuDefinitionInfoList *arch_query_cpu_definitions(Error **errp)
}
static void add_cpreg_to_hashtable(ARMCPU *cpu, const ARMCPRegInfo *r,
- void *opaque, int state,
+ void *opaque, int state, int secstate,
int crm, int opc1, int opc2)
{
/* Private utility function for define_one_arm_cp_reg_with_opaque():
@@ -3296,6 +3296,7 @@ static void add_cpreg_to_hashtable(ARMCPU *cpu, const ARMCPRegInfo *r,
uint32_t *key = g_new(uint32_t, 1);
ARMCPRegInfo *r2 = g_memdup(r, sizeof(ARMCPRegInfo));
int is64 = (r->type & ARM_CP_64BIT) ? 1 : 0;
+ int ns = (r->secure & ARM_CP_SECSTATE_NS) ? 1 : 0;
if (r->state == ARM_CP_STATE_BOTH && state == ARM_CP_STATE_AA32) {
/* The AArch32 view of a shared register sees the lower 32 bits
* of a 64 bit backing field. It is not migratable as the AArch64
@@ -3327,7 +3328,7 @@ static void add_cpreg_to_hashtable(ARMCPU *cpu, const ARMCPRegInfo *r,
*key = ENCODE_AA64_CP_REG(r2->cp, r2->crn, crm,
r2->opc0, opc1, opc2);
} else {
- *key = ENCODE_CP_REG(r2->cp, is64, r2->crn, crm, opc1, opc2);
+ *key = ENCODE_CP_REG(r2->cp, is64, ns, r2->crn, crm, opc1, opc2);
}
if (opaque) {
r2->opaque = opaque;
@@ -3477,7 +3478,7 @@ void define_one_arm_cp_reg_with_opaque(ARMCPU *cpu,
continue;
}
add_cpreg_to_hashtable(cpu, r, opaque, state,
- crm, opc1, opc2);
+ ARM_CP_SECSTATE_NS, crm, opc1, opc2);
}
}
}
diff --git a/target-arm/translate.c b/target-arm/translate.c
index 17c459a..b52c758 100644
--- a/target-arm/translate.c
+++ b/target-arm/translate.c
@@ -7091,7 +7091,7 @@ static int disas_coproc_insn(DisasContext *s, uint32_t insn)
rt = (insn >> 12) & 0xf;
ri = get_arm_cp_reginfo(s->cp_regs,
- ENCODE_CP_REG(cpnum, is64, crn, crm, opc1, opc2));
+ ENCODE_CP_REG(cpnum, is64, s->ns, crn, crm, opc1, opc2));
if (ri) {
/* Check access permissions */
if (!cp_access_ok(s->current_el, ri, isread)) {
@@ -7281,12 +7281,16 @@ static int disas_coproc_insn(DisasContext *s, uint32_t insn)
*/
if (is64) {
qemu_log_mask(LOG_UNIMP, "%s access to unsupported AArch32 "
- "64 bit system register cp:%d opc1: %d crm:%d\n",
- isread ? "read" : "write", cpnum, opc1, crm);
+ "64 bit system register cp:%d opc1: %d crm:%d "
+ "(%s)\n",
+ isread ? "read" : "write", cpnum, opc1, crm,
+ s->ns ? "non-secure" : "secure");
} else {
qemu_log_mask(LOG_UNIMP, "%s access to unsupported AArch32 "
- "system register cp:%d opc1:%d crn:%d crm:%d opc2:%d\n",
- isread ? "read" : "write", cpnum, opc1, crn, crm, opc2);
+ "system register cp:%d opc1:%d crn:%d crm:%d opc2:%d "
+ "(%s)\n",
+ isread ? "read" : "write", cpnum, opc1, crn, crm, opc2,
+ s->ns ? "non-secure" : "secure");
}
return 1;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash Greg Bellows
@ 2014-12-09 18:43 ` Peter Maydell
2014-12-09 19:00 ` Greg Bellows
0 siblings, 1 reply; 30+ messages in thread
From: Peter Maydell @ 2014-12-09 18:43 UTC (permalink / raw)
To: Greg Bellows
Cc: Sergey Fedorov, QEMU Developers, Fabian Aggeler,
Edgar E. Iglesias
On 17 November 2014 at 16:47, Greg Bellows <greg.bellows@linaro.org> wrote:
> Added additional NS-bit to CPREG hash encoding. Updated hash lookup
> locations to specify hash bit currently set to non-secure.
>
> Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
> Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
>
> ---
>
> v8 -> v9
> - Fixed CP_REG_NS_MASK
> - Changed ENCODE_CP_REG argument order so ns follows is64
> - Replaced use of CP_REG_NS_MASK with CP_REG_NS_SHIFT
> - Changed add_cpreg_to_hashtable argument order so ns follows is64
> - Replaced use of SCR_NS with ARM_CP_SECSTATE_NS on registration
> - Undid global replace of Aarch# with AArch# in translate.c
>
> v5 -> v6
> - Globally replace Aarch# with AArch#
> ---
> target-arm/cpu.h | 25 ++++++++++++++++++++-----
> target-arm/helper.c | 7 ++++---
> target-arm/translate.c | 14 +++++++++-----
> 3 files changed, 33 insertions(+), 13 deletions(-)
>
> diff --git a/target-arm/cpu.h b/target-arm/cpu.h
> index dd7d229..532f698 100644
> --- a/target-arm/cpu.h
> +++ b/target-arm/cpu.h
> @@ -879,6 +879,7 @@ void armv7m_nvic_complete_irq(void *opaque, int irq);
> * Crn, Crm, opc1, opc2 fields
> * 32 or 64 bit register (ie is it accessed via MRC/MCR
> * or via MRRC/MCRR?)
> + * non-secure/secure bank (AArch32 only)
> * We allow 4 bits for opc1 because MRRC/MCRR have a 4 bit field.
> * (In this case crn and opc2 should be zero.)
> * For AArch64, there is no 32/64 bit size distinction;
> @@ -896,9 +897,16 @@ void armv7m_nvic_complete_irq(void *opaque, int irq);
> #define CP_REG_AA64_SHIFT 28
> #define CP_REG_AA64_MASK (1 << CP_REG_AA64_SHIFT)
>
> -#define ENCODE_CP_REG(cp, is64, crn, crm, opc1, opc2) \
> - (((cp) << 16) | ((is64) << 15) | ((crn) << 11) | \
> - ((crm) << 7) | ((opc1) << 3) | (opc2))
> +/* To enable banking of coprocessor registers depending on ns-bit we
> + * add a bit to distinguish between secure and non-secure cpregs in the
> + * hashtable.
> + */
> +#define CP_REG_NS_SHIFT 29
> +#define CP_REG_NS_MASK (1 << CP_REG_NS_SHIFT)
> +
> +#define ENCODE_CP_REG(cp, is64, ns, crn, crm, opc1, opc2) \
> + ((ns) << CP_REG_NS_SHIFT | ((cp) << 16) | ((is64) << 15) | \
> + ((crn) << 11) | ((crm) << 7) | ((opc1) << 3) | (opc2))
We forgot about the uses of ENCODE_CP_REG in kvm32.c, so this
breaks compile on ARM. Since I've already put these patches into
target-arm.next, I'm going to just squash in the fix:
--- a/target-arm/kvm32.c
+++ b/target-arm/kvm32.c
@@ -51,17 +51,17 @@ bool kvm_arm_get_host_cpu_features(ARMHostCPUClass *ahcc)
struct kvm_one_reg idregs[] = {
{
.id = KVM_REG_ARM | KVM_REG_SIZE_U32
- | ENCODE_CP_REG(15, 0, 0, 0, 0, 0),
+ | ENCODE_CP_REG(15, 0, 0, 0, 0, 0, 0),
.addr = (uintptr_t)&midr,
},
{
.id = KVM_REG_ARM | KVM_REG_SIZE_U32
- | ENCODE_CP_REG(15, 0, 0, 1, 0, 0),
+ | ENCODE_CP_REG(15, 0, 0, 0, 1, 0, 0),
.addr = (uintptr_t)&id_pfr0,
},
{
.id = KVM_REG_ARM | KVM_REG_SIZE_U32
- | ENCODE_CP_REG(15, 0, 0, 2, 0, 0),
+ | ENCODE_CP_REG(15, 0, 0, 0, 2, 0, 0),
.addr = (uintptr_t)&id_isar0,
},
{
thanks
-- PMM
^ permalink raw reply [flat|nested] 30+ messages in thread* Re: [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash
2014-12-09 18:43 ` Peter Maydell
@ 2014-12-09 19:00 ` Greg Bellows
0 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-12-09 19:00 UTC (permalink / raw)
To: Peter Maydell
Cc: Sergey Fedorov, QEMU Developers, Fabian Aggeler,
Edgar E. Iglesias
[-- Attachment #1: Type: text/plain, Size: 3604 bytes --]
Sounds good. Thanks for catching and fixing this.
On 9 December 2014 at 12:43, Peter Maydell <peter.maydell@linaro.org> wrote:
> On 17 November 2014 at 16:47, Greg Bellows <greg.bellows@linaro.org>
> wrote:
> > Added additional NS-bit to CPREG hash encoding. Updated hash lookup
> > locations to specify hash bit currently set to non-secure.
> >
> > Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
> > Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
> >
> > ---
> >
> > v8 -> v9
> > - Fixed CP_REG_NS_MASK
> > - Changed ENCODE_CP_REG argument order so ns follows is64
> > - Replaced use of CP_REG_NS_MASK with CP_REG_NS_SHIFT
> > - Changed add_cpreg_to_hashtable argument order so ns follows is64
> > - Replaced use of SCR_NS with ARM_CP_SECSTATE_NS on registration
> > - Undid global replace of Aarch# with AArch# in translate.c
> >
> > v5 -> v6
> > - Globally replace Aarch# with AArch#
> > ---
> > target-arm/cpu.h | 25 ++++++++++++++++++++-----
> > target-arm/helper.c | 7 ++++---
> > target-arm/translate.c | 14 +++++++++-----
> > 3 files changed, 33 insertions(+), 13 deletions(-)
> >
> > diff --git a/target-arm/cpu.h b/target-arm/cpu.h
> > index dd7d229..532f698 100644
> > --- a/target-arm/cpu.h
> > +++ b/target-arm/cpu.h
> > @@ -879,6 +879,7 @@ void armv7m_nvic_complete_irq(void *opaque, int irq);
> > * Crn, Crm, opc1, opc2 fields
> > * 32 or 64 bit register (ie is it accessed via MRC/MCR
> > * or via MRRC/MCRR?)
> > + * non-secure/secure bank (AArch32 only)
> > * We allow 4 bits for opc1 because MRRC/MCRR have a 4 bit field.
> > * (In this case crn and opc2 should be zero.)
> > * For AArch64, there is no 32/64 bit size distinction;
> > @@ -896,9 +897,16 @@ void armv7m_nvic_complete_irq(void *opaque, int
> irq);
> > #define CP_REG_AA64_SHIFT 28
> > #define CP_REG_AA64_MASK (1 << CP_REG_AA64_SHIFT)
> >
> > -#define ENCODE_CP_REG(cp, is64, crn, crm, opc1, opc2) \
> > - (((cp) << 16) | ((is64) << 15) | ((crn) << 11) | \
> > - ((crm) << 7) | ((opc1) << 3) | (opc2))
> > +/* To enable banking of coprocessor registers depending on ns-bit we
> > + * add a bit to distinguish between secure and non-secure cpregs in the
> > + * hashtable.
> > + */
> > +#define CP_REG_NS_SHIFT 29
> > +#define CP_REG_NS_MASK (1 << CP_REG_NS_SHIFT)
> > +
> > +#define ENCODE_CP_REG(cp, is64, ns, crn, crm, opc1, opc2) \
> > + ((ns) << CP_REG_NS_SHIFT | ((cp) << 16) | ((is64) << 15) | \
> > + ((crn) << 11) | ((crm) << 7) | ((opc1) << 3) | (opc2))
>
> We forgot about the uses of ENCODE_CP_REG in kvm32.c, so this
> breaks compile on ARM. Since I've already put these patches into
> target-arm.next, I'm going to just squash in the fix:
>
> --- a/target-arm/kvm32.c
> +++ b/target-arm/kvm32.c
> @@ -51,17 +51,17 @@ bool kvm_arm_get_host_cpu_features(ARMHostCPUClass
> *ahcc)
> struct kvm_one_reg idregs[] = {
> {
> .id = KVM_REG_ARM | KVM_REG_SIZE_U32
> - | ENCODE_CP_REG(15, 0, 0, 0, 0, 0),
> + | ENCODE_CP_REG(15, 0, 0, 0, 0, 0, 0),
> .addr = (uintptr_t)&midr,
> },
> {
> .id = KVM_REG_ARM | KVM_REG_SIZE_U32
> - | ENCODE_CP_REG(15, 0, 0, 1, 0, 0),
> + | ENCODE_CP_REG(15, 0, 0, 0, 1, 0, 0),
> .addr = (uintptr_t)&id_pfr0,
> },
> {
> .id = KVM_REG_ARM | KVM_REG_SIZE_U32
> - | ENCODE_CP_REG(15, 0, 0, 2, 0, 0),
> + | ENCODE_CP_REG(15, 0, 0, 0, 2, 0, 0),
> .addr = (uintptr_t)&id_isar0,
> },
> {
>
> thanks
> -- PMM
>
[-- Attachment #2: Type: text/html, Size: 4784 bytes --]
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Qemu-devel] [PATCH v11 07/26] target-arm: insert AArch32 cpregs twice into hashtable
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (5 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 06/26] target-arm: add secure state bit to CPREG hash Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 08/26] target-arm: move AArch32 SCR into security reglist Greg Bellows
` (19 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Prepare for cp register banking by inserting every cp register twice,
once for secure world and once for non-secure world.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v10 -> v11
- Fix indentation
v8 -> v9
- Fixed setting of secure field in add_cpreg_to_hashtable so it uses secstate
and happens in all cases.
- Fixed check for disabling of migration to only occur on duplicately defined
reginfos.
- Fixed comment on disabling migration and reset and eliminated crn special
case.
- Reworked define_one_arm_cp_reg_with_opaque() secure case handling.
v7 -> v8
- Updated define registers asserts to allow either a non-zero fieldoffset or
non-zero bank_fieldoffsets.
- Updated CP register hashing to always set the register fieldoffset when
banked register offsets are specified.
v5 -> v6
- Fixed NS-bit number in the CPREG hash lookup from 27 to 29.
- Switched to dedicated CPREG secure flags.
- Fixed disablement of reset and migration of common 32/64-bit registers.
- Globally replace Aarch# with AArch#
v4 -> v5
- Added use of ARM CP secure/non-secure bank flags during register processing
in define_one_arm_cp_reg_with_opaque(). We now only register the specified
bank if only one flag is specified, otherwise we register both a secure and
non-secure instance.
---
target-arm/helper.c | 98 +++++++++++++++++++++++++++++++++++++++++++----------
1 file changed, 81 insertions(+), 17 deletions(-)
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 1aadb79..9a1915b5 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -3296,23 +3296,59 @@ static void add_cpreg_to_hashtable(ARMCPU *cpu, const ARMCPRegInfo *r,
uint32_t *key = g_new(uint32_t, 1);
ARMCPRegInfo *r2 = g_memdup(r, sizeof(ARMCPRegInfo));
int is64 = (r->type & ARM_CP_64BIT) ? 1 : 0;
- int ns = (r->secure & ARM_CP_SECSTATE_NS) ? 1 : 0;
- if (r->state == ARM_CP_STATE_BOTH && state == ARM_CP_STATE_AA32) {
- /* The AArch32 view of a shared register sees the lower 32 bits
- * of a 64 bit backing field. It is not migratable as the AArch64
- * view handles that. AArch64 also handles reset.
- * We assume it is a cp15 register if the .cp field is left unset.
+ int ns = (secstate & ARM_CP_SECSTATE_NS) ? 1 : 0;
+
+ /* Reset the secure state to the specific incoming state. This is
+ * necessary as the register may have been defined with both states.
+ */
+ r2->secure = secstate;
+
+ if (r->bank_fieldoffsets[0] && r->bank_fieldoffsets[1]) {
+ /* Register is banked (using both entries in array).
+ * Overwriting fieldoffset as the array is only used to define
+ * banked registers but later only fieldoffset is used.
*/
- if (r2->cp == 0) {
- r2->cp = 15;
+ r2->fieldoffset = r->bank_fieldoffsets[ns];
+ }
+
+ if (state == ARM_CP_STATE_AA32) {
+ if (r->bank_fieldoffsets[0] && r->bank_fieldoffsets[1]) {
+ /* If the register is banked then we don't need to migrate or
+ * reset the 32-bit instance in certain cases:
+ *
+ * 1) If the register has both 32-bit and 64-bit instances then we
+ * can count on the 64-bit instance taking care of the
+ * non-secure bank.
+ * 2) If ARMv8 is enabled then we can count on a 64-bit version
+ * taking care of the secure bank. This requires that separate
+ * 32 and 64-bit definitions are provided.
+ */
+ if ((r->state == ARM_CP_STATE_BOTH && ns) ||
+ (arm_feature(&cpu->env, ARM_FEATURE_V8) && !ns)) {
+ r2->type |= ARM_CP_NO_MIGRATE;
+ r2->resetfn = arm_cp_reset_ignore;
+ }
+ } else if ((secstate != r->secure) && !ns) {
+ /* The register is not banked so we only want to allow migration of
+ * the non-secure instance.
+ */
+ r2->type |= ARM_CP_NO_MIGRATE;
+ r2->resetfn = arm_cp_reset_ignore;
}
- r2->type |= ARM_CP_NO_MIGRATE;
- r2->resetfn = arm_cp_reset_ignore;
+
+ if (r->state == ARM_CP_STATE_BOTH) {
+ /* We assume it is a cp15 register if the .cp field is left unset.
+ */
+ if (r2->cp == 0) {
+ r2->cp = 15;
+ }
+
#ifdef HOST_WORDS_BIGENDIAN
- if (r2->fieldoffset) {
- r2->fieldoffset += sizeof(uint32_t);
- }
+ if (r2->fieldoffset) {
+ r2->fieldoffset += sizeof(uint32_t);
+ }
#endif
+ }
}
if (state == ARM_CP_STATE_AA64) {
/* To allow abbreviation of ARMCPRegInfo
@@ -3461,10 +3497,14 @@ void define_one_arm_cp_reg_with_opaque(ARMCPU *cpu,
*/
if (!(r->type & (ARM_CP_SPECIAL|ARM_CP_CONST))) {
if (r->access & PL3_R) {
- assert(r->fieldoffset || r->readfn);
+ assert((r->fieldoffset ||
+ (r->bank_fieldoffsets[0] && r->bank_fieldoffsets[1])) ||
+ r->readfn);
}
if (r->access & PL3_W) {
- assert(r->fieldoffset || r->writefn);
+ assert((r->fieldoffset ||
+ (r->bank_fieldoffsets[0] && r->bank_fieldoffsets[1])) ||
+ r->writefn);
}
}
/* Bad type field probably means missing sentinel at end of reg list */
@@ -3477,8 +3517,32 @@ void define_one_arm_cp_reg_with_opaque(ARMCPU *cpu,
if (r->state != state && r->state != ARM_CP_STATE_BOTH) {
continue;
}
- add_cpreg_to_hashtable(cpu, r, opaque, state,
- ARM_CP_SECSTATE_NS, crm, opc1, opc2);
+ if (state == ARM_CP_STATE_AA32) {
+ /* Under AArch32 CP registers can be common
+ * (same for secure and non-secure world) or banked.
+ */
+ switch (r->secure) {
+ case ARM_CP_SECSTATE_S:
+ case ARM_CP_SECSTATE_NS:
+ add_cpreg_to_hashtable(cpu, r, opaque, state,
+ r->secure, crm, opc1, opc2);
+ break;
+ default:
+ add_cpreg_to_hashtable(cpu, r, opaque, state,
+ ARM_CP_SECSTATE_S,
+ crm, opc1, opc2);
+ add_cpreg_to_hashtable(cpu, r, opaque, state,
+ ARM_CP_SECSTATE_NS,
+ crm, opc1, opc2);
+ break;
+ }
+ } else {
+ /* AArch64 registers get mapped to non-secure instance
+ * of AArch32 */
+ add_cpreg_to_hashtable(cpu, r, opaque, state,
+ ARM_CP_SECSTATE_NS,
+ crm, opc1, opc2);
+ }
}
}
}
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 08/26] target-arm: move AArch32 SCR into security reglist
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (6 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 07/26] target-arm: insert AArch32 cpregs twice into hashtable Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 09/26] target-arm: implement IRQ/FIQ routing to Monitor mode Greg Bellows
` (18 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Define a new ARM CP register info list for the ARMv7 Security Extension
feature. Register that list only for ARM cores with Security Extension/EL3
support. Moving AArch32 SCR into Security Extension register group.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v7 -> v8
- Fix SCR register fieldoffset to be offsetoflow32.
- Rename v7_el3_cp_reginfo to el3_cp_reginfo and remove v7 feature check when
defining. This allows all common v7/8 secure CP regs to be registered
together leaving the v8_el3_cp_reginfo to only v8 specific EL3 registers.
- Move SCR_EL3 into el3_cp_reginfo.
v4 -> v5
- Added reset value on SCR_EL3
- Squashed SCR Migration fix (previously patch 33)
This patch adds code to mark duplicate CP register registrations as
NO_MIGRATE to avoid duplicate migrations.
v3 -> v4
- Renamed security_cp_reginfo to v7_el3_cp_reginfo
- Conditionalized define on whether v7 or v8 were enabled
---
target-arm/helper.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 9a1915b5..6c4b467 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -898,9 +898,6 @@ static const ARMCPRegInfo v7_cp_reginfo[] = {
.access = PL1_RW, .writefn = vbar_write,
.fieldoffset = offsetof(CPUARMState, cp15.vbar_el[1]),
.resetvalue = 0 },
- { .name = "SCR", .cp = 15, .crn = 1, .crm = 1, .opc1 = 0, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetoflow32(CPUARMState, cp15.scr_el3),
- .resetvalue = 0, .writefn = scr_write },
{ .name = "CCSIDR", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .crn = 0, .crm = 0, .opc1 = 1, .opc2 = 0,
.access = PL1_R, .readfn = ccsidr_read, .type = ARM_CP_NO_MIGRATE },
@@ -2335,11 +2332,18 @@ static const ARMCPRegInfo v8_el3_cp_reginfo[] = {
.access = PL3_RW, .writefn = vbar_write,
.fieldoffset = offsetof(CPUARMState, cp15.vbar_el[3]),
.resetvalue = 0 },
+ REGINFO_SENTINEL
+};
+
+static const ARMCPRegInfo el3_cp_reginfo[] = {
{ .name = "SCR_EL3", .state = ARM_CP_STATE_AA64,
- .type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 6, .crn = 1, .crm = 1, .opc2 = 0,
.access = PL3_RW, .fieldoffset = offsetof(CPUARMState, cp15.scr_el3),
- .writefn = scr_write },
+ .resetvalue = 0, .writefn = scr_write },
+ { .name = "SCR", .type = ARM_CP_NO_MIGRATE,
+ .cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 0,
+ .access = PL3_RW, .fieldoffset = offsetoflow32(CPUARMState, cp15.scr_el3),
+ .resetfn = arm_cp_reset_ignore, .writefn = scr_write },
REGINFO_SENTINEL
};
@@ -2960,7 +2964,10 @@ void register_cp_regs_for_features(ARMCPU *cpu)
}
}
if (arm_feature(env, ARM_FEATURE_EL3)) {
- define_arm_cp_regs(cpu, v8_el3_cp_reginfo);
+ if (arm_feature(env, ARM_FEATURE_V8)) {
+ define_arm_cp_regs(cpu, v8_el3_cp_reginfo);
+ }
+ define_arm_cp_regs(cpu, el3_cp_reginfo);
}
if (arm_feature(env, ARM_FEATURE_MPU)) {
/* These are the MPU registers prior to PMSAv6. Any new
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 09/26] target-arm: implement IRQ/FIQ routing to Monitor mode
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (7 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 08/26] target-arm: move AArch32 SCR into security reglist Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 10/26] target-arm: add NSACR register Greg Bellows
` (17 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
SCR.{IRQ/FIQ} bits allow to route IRQ/FIQ exceptions to monitor CPU
mode. When taking IRQ exception to monitor mode FIQ exception is
additionally masked.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
target-arm/helper.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 6c4b467..8651bbc 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -4233,12 +4233,21 @@ void arm_cpu_do_interrupt(CPUState *cs)
/* Disable IRQ and imprecise data aborts. */
mask = CPSR_A | CPSR_I;
offset = 4;
+ if (env->cp15.scr_el3 & SCR_IRQ) {
+ /* IRQ routed to monitor mode */
+ new_mode = ARM_CPU_MODE_MON;
+ mask |= CPSR_F;
+ }
break;
case EXCP_FIQ:
new_mode = ARM_CPU_MODE_FIQ;
addr = 0x1c;
/* Disable FIQ, IRQ and imprecise data aborts. */
mask = CPSR_A | CPSR_I | CPSR_F;
+ if (env->cp15.scr_el3 & SCR_FIQ) {
+ /* FIQ routed to monitor mode */
+ new_mode = ARM_CPU_MODE_MON;
+ }
offset = 4;
break;
case EXCP_SMC:
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 10/26] target-arm: add NSACR register
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (8 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 09/26] target-arm: implement IRQ/FIQ routing to Monitor mode Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 11/26] target-arm: add SDER definition Greg Bellows
` (16 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Implements NSACR register with corresponding read/write functions
for ARMv7 and ARMv8.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Removed unused NSACR constants
- Added TODO for trapping secure EL1 accesses to NSACR
- Change NSACR access from PL3_RW to PL3_W
- Fixed declaration order of the NSACR register components
v7 -> v8
- Update naming from c1_nsacr to nsacr to match other registers being changed.
- Remove NSACR read/write functions
v4 -> v5
- Changed to use renamed arm_current_el()
---
target-arm/cpu.h | 1 +
target-arm/helper.c | 4 ++++
2 files changed, 5 insertions(+)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 532f698..2afe93a 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -181,6 +181,7 @@ typedef struct CPUARMState {
uint64_t c1_sys; /* System control register. */
uint64_t c1_coproc; /* Coprocessor access register. */
uint32_t c1_xscaleauxcr; /* XScale auxiliary control register. */
+ uint32_t nsacr; /* Non-secure access control register. */
uint64_t ttbr0_el1; /* MMU translation table base 0. */
uint64_t ttbr1_el1; /* MMU translation table base 1. */
uint64_t c2_control; /* MMU translation table base control. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 8651bbc..691bb8e 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -2344,6 +2344,10 @@ static const ARMCPRegInfo el3_cp_reginfo[] = {
.cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 0,
.access = PL3_RW, .fieldoffset = offsetoflow32(CPUARMState, cp15.scr_el3),
.resetfn = arm_cp_reset_ignore, .writefn = scr_write },
+ /* TODO: Implement NSACR trapping of secure EL1 accesses to EL3 */
+ { .name = "NSACR", .cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 2,
+ .access = PL3_W | PL1_R, .resetvalue = 0,
+ .fieldoffset = offsetof(CPUARMState, cp15.nsacr) },
REGINFO_SENTINEL
};
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 11/26] target-arm: add SDER definition
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (9 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 10/26] target-arm: add NSACR register Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 12/26] target-arm: add MVBAR support Greg Bellows
` (15 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
Added CP register defintions for SDER and SDER32_EL3 as well as cp15.sder for
register storage.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Fixed declaration order of the SDER register components
v7 -> v8
- Added SDER32_EL3 register definition
- Changed sder name from c1_sder to sder
- Changed sder from uint32_t to uint64_t.
---
target-arm/cpu.h | 1 +
target-arm/helper.c | 8 ++++++++
2 files changed, 9 insertions(+)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 2afe93a..12bd6ec 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -181,6 +181,7 @@ typedef struct CPUARMState {
uint64_t c1_sys; /* System control register. */
uint64_t c1_coproc; /* Coprocessor access register. */
uint32_t c1_xscaleauxcr; /* XScale auxiliary control register. */
+ uint64_t sder; /* Secure debug enable register. */
uint32_t nsacr; /* Non-secure access control register. */
uint64_t ttbr0_el1; /* MMU translation table base 0. */
uint64_t ttbr1_el1; /* MMU translation table base 1. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 691bb8e..284f255 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -2344,6 +2344,14 @@ static const ARMCPRegInfo el3_cp_reginfo[] = {
.cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 0,
.access = PL3_RW, .fieldoffset = offsetoflow32(CPUARMState, cp15.scr_el3),
.resetfn = arm_cp_reset_ignore, .writefn = scr_write },
+ { .name = "SDER32_EL3", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 6, .crn = 1, .crm = 1, .opc2 = 1,
+ .access = PL3_RW, .resetvalue = 0,
+ .fieldoffset = offsetof(CPUARMState, cp15.sder) },
+ { .name = "SDER",
+ .cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 1,
+ .access = PL3_RW, .resetvalue = 0,
+ .fieldoffset = offsetoflow32(CPUARMState, cp15.sder) },
/* TODO: Implement NSACR trapping of secure EL1 accesses to EL3 */
{ .name = "NSACR", .cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 2,
.access = PL3_W | PL1_R, .resetvalue = 0,
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 12/26] target-arm: add MVBAR support
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (10 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 11/26] target-arm: add SDER definition Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 13/26] target-arm: add SCTLR_EL3 and make SCTLR banked Greg Bellows
` (14 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Use MVBAR register as exception vector base address for
exceptions taken to CPU monitor mode.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Fixed declaration order of the MVBARR register components
v7 -> v8
- Changed the mvbar cp15 storage from uint64_t to uint32_t
---
target-arm/cpu.h | 1 +
target-arm/helper.c | 15 +++++++++------
2 files changed, 10 insertions(+), 6 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 12bd6ec..cdf2dd7 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -211,6 +211,7 @@ typedef struct CPUARMState {
uint32_t c9_pminten; /* perf monitor interrupt enables */
uint64_t mair_el1;
uint64_t vbar_el[4]; /* vector base address register */
+ uint32_t mvbar; /* (monitor) vector base address register */
uint32_t c13_fcse; /* FCSE PID. */
uint64_t contextidr_el1; /* Context ID. */
uint64_t tpidr_el0; /* User RW Thread register. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 284f255..a2643fe 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -2356,6 +2356,9 @@ static const ARMCPRegInfo el3_cp_reginfo[] = {
{ .name = "NSACR", .cp = 15, .opc1 = 0, .crn = 1, .crm = 1, .opc2 = 2,
.access = PL3_W | PL1_R, .resetvalue = 0,
.fieldoffset = offsetof(CPUARMState, cp15.nsacr) },
+ { .name = "MVBAR", .cp = 15, .opc1 = 0, .crn = 12, .crm = 0, .opc2 = 1,
+ .access = PL3_RW, .writefn = vbar_write, .resetvalue = 0,
+ .fieldoffset = offsetof(CPUARMState, cp15.mvbar) },
REGINFO_SENTINEL
};
@@ -4272,16 +4275,16 @@ void arm_cpu_do_interrupt(CPUState *cs)
cpu_abort(cs, "Unhandled exception 0x%x\n", cs->exception_index);
return; /* Never happens. Keep compiler happy. */
}
- /* High vectors. */
- if (env->cp15.c1_sys & SCTLR_V) {
- /* when enabled, base address cannot be remapped. */
+
+ if (new_mode == ARM_CPU_MODE_MON) {
+ addr += env->cp15.mvbar;
+ } else if (env->cp15.c1_sys & SCTLR_V) {
+ /* High vectors. When enabled, base address cannot be remapped. */
addr += 0xffff0000;
} else {
/* ARM v7 architectures provide a vector base address register to remap
* the interrupt vector table.
- * This register is only followed in non-monitor mode, and has a secure
- * and un-secure copy. Since the cpu is always in a un-secure operation
- * and is never in monitor mode this feature is always active.
+ * This register is only followed in non-monitor mode, and is banked.
* Note: only bits 31:5 are valid.
*/
addr += env->cp15.vbar_el[1];
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 13/26] target-arm: add SCTLR_EL3 and make SCTLR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (11 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 12/26] target-arm: add MVBAR support Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 14/26] target-arm: respect SCR.FW, SCR.AW and SCTLR.NMFI Greg Bellows
` (13 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Implements SCTLR_EL3 and uses secure/non-secure instance when
needed.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v9 -> v10
- Fix SCTLR to use opc0 instead of cp
v8 -> v9
- Remove the v8 check in arm_cpu_reset when setting regs[15]
- Fix SCTLR definition component order
v5 -> v6
- Changed _el field variants to be array based
- Consolidate SCTLR and SCTLR_EL1 reginfo entries
---
hw/arm/pxa2xx.c | 2 +-
target-arm/cpu.c | 8 ++++--
target-arm/cpu.h | 10 ++++++-
target-arm/helper.c | 72 +++++++++++++++++++++++++++++---------------------
target-arm/op_helper.c | 2 +-
5 files changed, 59 insertions(+), 35 deletions(-)
diff --git a/hw/arm/pxa2xx.c b/hw/arm/pxa2xx.c
index 693dfec..11d51af 100644
--- a/hw/arm/pxa2xx.c
+++ b/hw/arm/pxa2xx.c
@@ -273,7 +273,7 @@ static void pxa2xx_pwrmode_write(CPUARMState *env, const ARMCPRegInfo *ri,
case 3:
s->cpu->env.uncached_cpsr = ARM_CPU_MODE_SVC;
s->cpu->env.daif = PSTATE_A | PSTATE_F | PSTATE_I;
- s->cpu->env.cp15.c1_sys = 0;
+ s->cpu->env.cp15.sctlr_ns = 0;
s->cpu->env.cp15.c1_coproc = 0;
s->cpu->env.cp15.ttbr0_el1 = 0;
s->cpu->env.cp15.c3 = 0;
diff --git a/target-arm/cpu.c b/target-arm/cpu.c
index 5ce7350..fdb7b35 100644
--- a/target-arm/cpu.c
+++ b/target-arm/cpu.c
@@ -109,7 +109,7 @@ static void arm_cpu_reset(CPUState *s)
#if defined(CONFIG_USER_ONLY)
env->pstate = PSTATE_MODE_EL0t;
/* Userspace expects access to DC ZVA, CTL_EL0 and the cache ops */
- env->cp15.c1_sys |= SCTLR_UCT | SCTLR_UCI | SCTLR_DZE;
+ env->cp15.sctlr_el[1] |= SCTLR_UCT | SCTLR_UCI | SCTLR_DZE;
/* and to the FP/Neon instructions */
env->cp15.c1_coproc = deposit64(env->cp15.c1_coproc, 20, 2, 3);
#else
@@ -167,7 +167,11 @@ static void arm_cpu_reset(CPUState *s)
env->thumb = initial_pc & 1;
}
- if (env->cp15.c1_sys & SCTLR_V) {
+ /* AArch32 has a hard highvec setting of 0xFFFF0000. If we are currently
+ * executing as AArch32 then check if highvecs are enabled and
+ * adjust the PC accordingly.
+ */
+ if (A32_BANKED_CURRENT_REG_GET(env, sctlr) & SCTLR_V) {
env->regs[15] = 0xFFFF0000;
}
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index cdf2dd7..6559aa8 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -178,7 +178,15 @@ typedef struct CPUARMState {
struct {
uint32_t c0_cpuid;
uint64_t c0_cssel; /* Cache size selection. */
- uint64_t c1_sys; /* System control register. */
+ union { /* System control register. */
+ struct {
+ uint64_t _unused_sctlr;
+ uint64_t sctlr_ns;
+ uint64_t hsctlr;
+ uint64_t sctlr_s;
+ };
+ uint64_t sctlr_el[4];
+ };
uint64_t c1_coproc; /* Coprocessor access register. */
uint32_t c1_xscaleauxcr; /* XScale auxiliary control register. */
uint64_t sder; /* Secure debug enable register. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index a2643fe..1148273 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -1908,7 +1908,7 @@ static void aa64_fpsr_write(CPUARMState *env, const ARMCPRegInfo *ri,
static CPAccessResult aa64_daif_access(CPUARMState *env, const ARMCPRegInfo *ri)
{
- if (arm_current_el(env) == 0 && !(env->cp15.c1_sys & SCTLR_UMA)) {
+ if (arm_current_el(env) == 0 && !(env->cp15.sctlr_el[1] & SCTLR_UMA)) {
return CP_ACCESS_TRAP;
}
return CP_ACCESS_OK;
@@ -1926,7 +1926,7 @@ static CPAccessResult aa64_cacheop_access(CPUARMState *env,
/* Cache invalidate/clean: NOP, but EL0 must UNDEF unless
* SCTLR_EL1.UCI is set.
*/
- if (arm_current_el(env) == 0 && !(env->cp15.c1_sys & SCTLR_UCI)) {
+ if (arm_current_el(env) == 0 && !(env->cp15.sctlr_el[1] & SCTLR_UCI)) {
return CP_ACCESS_TRAP;
}
return CP_ACCESS_OK;
@@ -2003,7 +2003,7 @@ static CPAccessResult aa64_zva_access(CPUARMState *env, const ARMCPRegInfo *ri)
/* We don't implement EL2, so the only control on DC ZVA is the
* bit in the SCTLR which can prohibit access for EL0.
*/
- if (arm_current_el(env) == 0 && !(env->cp15.c1_sys & SCTLR_DZE)) {
+ if (arm_current_el(env) == 0 && !(env->cp15.sctlr_el[1] & SCTLR_DZE)) {
return CP_ACCESS_TRAP;
}
return CP_ACCESS_OK;
@@ -2042,6 +2042,24 @@ static void spsel_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t val)
update_spsel(env, val);
}
+static void sctlr_write(CPUARMState *env, const ARMCPRegInfo *ri,
+ uint64_t value)
+{
+ ARMCPU *cpu = arm_env_get_cpu(env);
+
+ if (raw_read(env, ri) == value) {
+ /* Skip the TLB flush if nothing actually changed; Linux likes
+ * to do a lot of pointless SCTLR writes.
+ */
+ return;
+ }
+
+ raw_write(env, ri, value);
+ /* ??? Lots of these bits are not implemented. */
+ /* This may enable/disable the MMU, so do a TLB flush. */
+ tlb_flush(CPU(cpu), 1);
+}
+
static const ARMCPRegInfo v8_cp_reginfo[] = {
/* Minimal set of EL0-visible registers. This will need to be expanded
* significantly for system emulation of AArch64 CPUs.
@@ -2311,6 +2329,10 @@ static const ARMCPRegInfo v8_el2_cp_reginfo[] = {
};
static const ARMCPRegInfo v8_el3_cp_reginfo[] = {
+ { .name = "SCTLR_EL3", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 6, .crn = 1, .crm = 0, .opc2 = 0,
+ .access = PL3_RW, .raw_writefn = raw_write, .writefn = sctlr_write,
+ .fieldoffset = offsetof(CPUARMState, cp15.sctlr_el[3]) },
{ .name = "ELR_EL3", .state = ARM_CP_STATE_AA64,
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 6, .crn = 4, .crm = 0, .opc2 = 1,
@@ -2362,30 +2384,12 @@ static const ARMCPRegInfo el3_cp_reginfo[] = {
REGINFO_SENTINEL
};
-static void sctlr_write(CPUARMState *env, const ARMCPRegInfo *ri,
- uint64_t value)
-{
- ARMCPU *cpu = arm_env_get_cpu(env);
-
- if (raw_read(env, ri) == value) {
- /* Skip the TLB flush if nothing actually changed; Linux likes
- * to do a lot of pointless SCTLR writes.
- */
- return;
- }
-
- raw_write(env, ri, value);
- /* ??? Lots of these bits are not implemented. */
- /* This may enable/disable the MMU, so do a TLB flush. */
- tlb_flush(CPU(cpu), 1);
-}
-
static CPAccessResult ctr_el0_access(CPUARMState *env, const ARMCPRegInfo *ri)
{
/* Only accessible in EL0 if SCTLR.UCT is set (and only in AArch64,
* but the AArch32 CTR has its own reginfo struct)
*/
- if (arm_current_el(env) == 0 && !(env->cp15.c1_sys & SCTLR_UCT)) {
+ if (arm_current_el(env) == 0 && !(env->cp15.sctlr_el[1] & SCTLR_UCT)) {
return CP_ACCESS_TRAP;
}
return CP_ACCESS_OK;
@@ -3182,8 +3186,10 @@ void register_cp_regs_for_features(ARMCPU *cpu)
{
ARMCPRegInfo sctlr = {
.name = "SCTLR", .state = ARM_CP_STATE_BOTH,
- .opc0 = 3, .crn = 1, .crm = 0, .opc1 = 0, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.c1_sys),
+ .opc0 = 3, .opc1 = 0, .crn = 1, .crm = 0, .opc2 = 0,
+ .access = PL1_RW,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.sctlr_s),
+ offsetof(CPUARMState, cp15.sctlr_ns) },
.writefn = sctlr_write, .resetvalue = cpu->reset_sctlr,
.raw_writefn = raw_write,
};
@@ -4278,7 +4284,7 @@ void arm_cpu_do_interrupt(CPUState *cs)
if (new_mode == ARM_CPU_MODE_MON) {
addr += env->cp15.mvbar;
- } else if (env->cp15.c1_sys & SCTLR_V) {
+ } else if (A32_BANKED_CURRENT_REG_GET(env, sctlr) & SCTLR_V) {
/* High vectors. When enabled, base address cannot be remapped. */
addr += 0xffff0000;
} else {
@@ -4308,7 +4314,7 @@ void arm_cpu_do_interrupt(CPUState *cs)
/* this is a lie, as the was no c1_sys on V4T/V5, but who cares
* and we should just guard the thumb mode on V4 */
if (arm_feature(env, ARM_FEATURE_V4T)) {
- env->thumb = (env->cp15.c1_sys & SCTLR_TE) != 0;
+ env->thumb = (A32_BANKED_CURRENT_REG_GET(env, sctlr) & SCTLR_TE) != 0;
}
env->regs[14] = env->regs[15] + offset;
env->regs[15] = addr;
@@ -4339,7 +4345,7 @@ static inline int check_ap(CPUARMState *env, int ap, int domain_prot,
}
if (access_type == 1)
return 0;
- switch (env->cp15.c1_sys & (SCTLR_S | SCTLR_R)) {
+ switch (A32_BANKED_CURRENT_REG_GET(env, sctlr) & (SCTLR_S | SCTLR_R)) {
case SCTLR_S:
return is_user ? 0 : PAGE_READ;
case SCTLR_R:
@@ -4588,7 +4594,8 @@ static int get_phys_addr_v6(CPUARMState *env, uint32_t address, int access_type,
goto do_fault;
/* The simplified model uses AP[0] as an access control bit. */
- if ((env->cp15.c1_sys & SCTLR_AFE) && (ap & 1) == 0) {
+ if ((A32_BANKED_CURRENT_REG_GET(env, sctlr) & SCTLR_AFE)
+ && (ap & 1) == 0) {
/* Access flag fault. */
code = (code == 15) ? 6 : 3;
goto do_fault;
@@ -4919,11 +4926,16 @@ static inline int get_phys_addr(CPUARMState *env, target_ulong address,
hwaddr *phys_ptr, int *prot,
target_ulong *page_size)
{
+ /* This is not entirely correct as get_phys_addr() can also be called
+ * from ats_write() for an address translation of a specific regime.
+ */
+ uint32_t sctlr = A32_BANKED_CURRENT_REG_GET(env, sctlr);
+
/* Fast Context Switch Extension. */
if (address < 0x02000000)
address += env->cp15.c13_fcse;
- if ((env->cp15.c1_sys & SCTLR_M) == 0) {
+ if ((sctlr & SCTLR_M) == 0) {
/* MMU/MPU disabled. */
*phys_ptr = address;
*prot = PAGE_READ | PAGE_WRITE | PAGE_EXEC;
@@ -4936,7 +4948,7 @@ static inline int get_phys_addr(CPUARMState *env, target_ulong address,
} else if (extended_addresses_enabled(env)) {
return get_phys_addr_lpae(env, address, access_type, is_user, phys_ptr,
prot, page_size);
- } else if (env->cp15.c1_sys & SCTLR_XP) {
+ } else if (sctlr & SCTLR_XP) {
return get_phys_addr_v6(env, address, access_type, is_user, phys_ptr,
prot, page_size);
} else {
diff --git a/target-arm/op_helper.c b/target-arm/op_helper.c
index 62012c3..a8dea5a 100644
--- a/target-arm/op_helper.c
+++ b/target-arm/op_helper.c
@@ -361,7 +361,7 @@ void HELPER(msr_i_pstate)(CPUARMState *env, uint32_t op, uint32_t imm)
* Note that SPSel is never OK from EL0; we rely on handle_msr_i()
* to catch that case at translate time.
*/
- if (arm_current_el(env) == 0 && !(env->cp15.c1_sys & SCTLR_UMA)) {
+ if (arm_current_el(env) == 0 && !(env->cp15.sctlr_el[1] & SCTLR_UMA)) {
raise_exception(env, EXCP_UDEF);
}
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 14/26] target-arm: respect SCR.FW, SCR.AW and SCTLR.NMFI
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (12 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 13/26] target-arm: add SCTLR_EL3 and make SCTLR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 15/26] target-arm: make CSSELR banked Greg Bellows
` (12 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Add checks of SCR AW/FW bits when performing writes of CPSR. These SCR bits
are used to control whether the CPSR masking bits can be adjusted from
non-secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v10 -> v11
- Moved cpsr_write() uncached_cpsr updated to before the mode setting.
v8 -> v9
- Move cpsr_write mask filtering above mode switch.
- Replace conditional checks removed in v8.
v7 -> v8
- Fixed incorrect use of env->uncached_cpsr A/I/F to use env->daif instead.
- Removed incorrect statement about SPSR to CPSR copies being affected by
SCR.AW/FW.
- Fix typo in comment.
- Simpified cpsr_write logic
v3 -> v4
- Fixed up conditions for ignoring CPSR.A/F updates by isolating to v7 and
checking for the existence of EL3 and non-existence of EL2.
---
target-arm/helper.c | 54 +++++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 1148273..d555fe4 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -3644,6 +3644,8 @@ uint32_t cpsr_read(CPUARMState *env)
void cpsr_write(CPUARMState *env, uint32_t val, uint32_t mask)
{
+ uint32_t changed_daif;
+
if (mask & CPSR_NZCV) {
env->ZF = (~val) & CPSR_Z;
env->NF = val;
@@ -3666,6 +3668,58 @@ void cpsr_write(CPUARMState *env, uint32_t val, uint32_t mask)
env->GE = (val >> 16) & 0xf;
}
+ /* In a V7 implementation that includes the security extensions but does
+ * not include Virtualization Extensions the SCR.FW and SCR.AW bits control
+ * whether non-secure software is allowed to change the CPSR_F and CPSR_A
+ * bits respectively.
+ *
+ * In a V8 implementation, it is permitted for privileged software to
+ * change the CPSR A/F bits regardless of the SCR.AW/FW bits.
+ */
+ if (!arm_feature(env, ARM_FEATURE_V8) &&
+ arm_feature(env, ARM_FEATURE_EL3) &&
+ !arm_feature(env, ARM_FEATURE_EL2) &&
+ !arm_is_secure(env)) {
+
+ changed_daif = (env->daif ^ val) & mask;
+
+ if (changed_daif & CPSR_A) {
+ /* Check to see if we are allowed to change the masking of async
+ * abort exceptions from a non-secure state.
+ */
+ if (!(env->cp15.scr_el3 & SCR_AW)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "Ignoring attempt to switch CPSR_A flag from "
+ "non-secure world with SCR.AW bit clear\n");
+ mask &= ~CPSR_A;
+ }
+ }
+
+ if (changed_daif & CPSR_F) {
+ /* Check to see if we are allowed to change the masking of FIQ
+ * exceptions from a non-secure state.
+ */
+ if (!(env->cp15.scr_el3 & SCR_FW)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "Ignoring attempt to switch CPSR_F flag from "
+ "non-secure world with SCR.FW bit clear\n");
+ mask &= ~CPSR_F;
+ }
+
+ /* Check whether non-maskable FIQ (NMFI) support is enabled.
+ * If this bit is set software is not allowed to mask
+ * FIQs, but is allowed to set CPSR_F to 0.
+ */
+ if ((A32_BANKED_CURRENT_REG_GET(env, sctlr) & SCTLR_NMFI) &&
+ (val & CPSR_F)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "Ignoring attempt to enable CPSR_F flag "
+ "(non-maskable FIQ [NMFI] support enabled)\n");
+ mask &= ~CPSR_F;
+ }
+ }
+ }
+
env->daif &= ~(CPSR_AIF & mask);
env->daif |= val & CPSR_AIF & mask;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 15/26] target-arm: make CSSELR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (13 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 14/26] target-arm: respect SCR.FW, SCR.AW and SCTLR.NMFI Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 16/26] target-arm: make TTBR0/1 banked Greg Bellows
` (11 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Rename CSSELR (cache size selection register) and add secure
instance (AArch32).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Replaced call to ARM_CP_SECSTATE_TEST with direct access
v7 -> v8
- Fix CSSELR CP register definition to use .opc0 rather than .cp.
v5 -> v6
- Changed _el field variants to be array based
- Switch to use distinct CPREG secure flags.
- Merged CSSELR and CSSELR_EL1 reginfo entries
v4 -> v5
- Changed to use the CCSIDR cpreg bank flag to select the csselr bank instead
of the A32_BANKED macro. This more accurately uses the secure state bank
matching the CCSIDR.
---
target-arm/cpu.h | 10 +++++++++-
target-arm/helper.c | 14 +++++++++++---
2 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 6559aa8..f06d209 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -177,7 +177,15 @@ typedef struct CPUARMState {
/* System control coprocessor (cp15) */
struct {
uint32_t c0_cpuid;
- uint64_t c0_cssel; /* Cache size selection. */
+ union { /* Cache size selection */
+ struct {
+ uint64_t _unused_csselr0;
+ uint64_t csselr_ns;
+ uint64_t _unused_csselr1;
+ uint64_t csselr_s;
+ };
+ uint64_t csselr_el[4];
+ };
union { /* System control register. */
struct {
uint64_t _unused_sctlr;
diff --git a/target-arm/helper.c b/target-arm/helper.c
index d555fe4..05e66fb 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -776,7 +776,14 @@ static void scr_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t value)
static uint64_t ccsidr_read(CPUARMState *env, const ARMCPRegInfo *ri)
{
ARMCPU *cpu = arm_env_get_cpu(env);
- return cpu->ccsidr[env->cp15.c0_cssel];
+
+ /* Acquire the CSSELR index from the bank corresponding to the CCSIDR
+ * bank
+ */
+ uint32_t index = A32_BANKED_REG_GET(env, csselr,
+ ri->secure & ARM_CP_SECSTATE_S);
+
+ return cpu->ccsidr[index];
}
static void csselr_write(CPUARMState *env, const ARMCPRegInfo *ri,
@@ -903,8 +910,9 @@ static const ARMCPRegInfo v7_cp_reginfo[] = {
.access = PL1_R, .readfn = ccsidr_read, .type = ARM_CP_NO_MIGRATE },
{ .name = "CSSELR", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .crn = 0, .crm = 0, .opc1 = 2, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.c0_cssel),
- .writefn = csselr_write, .resetvalue = 0 },
+ .access = PL1_RW, .writefn = csselr_write, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.csselr_s),
+ offsetof(CPUARMState, cp15.csselr_ns) } },
/* Auxiliary ID register: this actually has an IMPDEF value but for now
* just RAZ for all cores:
*/
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 16/26] target-arm: make TTBR0/1 banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (14 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 15/26] target-arm: make CSSELR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 17/26] target-arm: make TTBCR banked Greg Bellows
` (10 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Adds secure and non-secure bank register suport for TTBR0 and TTBR1.
Changes include adding secure and non-secure instances of ttbr0 and ttbr1 as
well as a CP register definition for TTBR0_EL3. Added a union containing
both EL based array fields and secure and non-secure fields mapped to them.
Updated accesses to use A32_BANKED_CURRENT_REG_GET macro.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Fixed naming of TTBR0/1 and defined with opc0 instead of cp
- Removed get_phys_addr_lpae() AArch64 EL3 support.
- Remove stray whitespace change in pxa2xx.c
v5 -> v6
- Changed _el field variants to be array based
- Merged TTBR# and TTBR#_EL1 reginfo entries
- Globally replace Aarch# with AArch#
---
hw/arm/pxa2xx.c | 2 +-
target-arm/cpu.h | 20 ++++++++++++++++++--
target-arm/helper.c | 37 +++++++++++++++++++++++++------------
3 files changed, 44 insertions(+), 15 deletions(-)
diff --git a/hw/arm/pxa2xx.c b/hw/arm/pxa2xx.c
index 11d51af..2b00b59 100644
--- a/hw/arm/pxa2xx.c
+++ b/hw/arm/pxa2xx.c
@@ -275,7 +275,7 @@ static void pxa2xx_pwrmode_write(CPUARMState *env, const ARMCPRegInfo *ri,
s->cpu->env.daif = PSTATE_A | PSTATE_F | PSTATE_I;
s->cpu->env.cp15.sctlr_ns = 0;
s->cpu->env.cp15.c1_coproc = 0;
- s->cpu->env.cp15.ttbr0_el1 = 0;
+ s->cpu->env.cp15.ttbr0_el[1] = 0;
s->cpu->env.cp15.c3 = 0;
s->pm_regs[PSSR >> 2] |= 0x8; /* Set STS */
s->pm_regs[RCSR >> 2] |= 0x8; /* Set GPR */
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index f06d209..efe7010 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -199,8 +199,24 @@ typedef struct CPUARMState {
uint32_t c1_xscaleauxcr; /* XScale auxiliary control register. */
uint64_t sder; /* Secure debug enable register. */
uint32_t nsacr; /* Non-secure access control register. */
- uint64_t ttbr0_el1; /* MMU translation table base 0. */
- uint64_t ttbr1_el1; /* MMU translation table base 1. */
+ union { /* MMU translation table base 0. */
+ struct {
+ uint64_t _unused_ttbr0_0;
+ uint64_t ttbr0_ns;
+ uint64_t _unused_ttbr0_1;
+ uint64_t ttbr0_s;
+ };
+ uint64_t ttbr0_el[4];
+ };
+ union { /* MMU translation table base 1. */
+ struct {
+ uint64_t _unused_ttbr1_0;
+ uint64_t ttbr1_ns;
+ uint64_t _unused_ttbr1_1;
+ uint64_t ttbr1_s;
+ };
+ uint64_t ttbr1_el[4];
+ };
uint64_t c2_control; /* MMU translation table base control. */
uint32_t c2_mask; /* MMU translation table base selection mask. */
uint32_t c2_base_mask; /* MMU translation table base 0 mask. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 05e66fb..908082c 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -1646,13 +1646,15 @@ static const ARMCPRegInfo vmsa_cp_reginfo[] = {
.access = PL1_RW,
.fieldoffset = offsetof(CPUARMState, cp15.esr_el[1]), .resetvalue = 0, },
{ .name = "TTBR0_EL1", .state = ARM_CP_STATE_BOTH,
- .opc0 = 3, .crn = 2, .crm = 0, .opc1 = 0, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.ttbr0_el1),
- .writefn = vmsa_ttbr_write, .resetvalue = 0 },
+ .opc0 = 3, .opc1 = 0, .crn = 2, .crm = 0, .opc2 = 0,
+ .access = PL1_RW, .writefn = vmsa_ttbr_write, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.ttbr0_s),
+ offsetof(CPUARMState, cp15.ttbr0_ns) } },
{ .name = "TTBR1_EL1", .state = ARM_CP_STATE_BOTH,
- .opc0 = 3, .crn = 2, .crm = 0, .opc1 = 0, .opc2 = 1,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.ttbr1_el1),
- .writefn = vmsa_ttbr_write, .resetvalue = 0 },
+ .opc0 = 3, .opc1 = 0, .crn = 2, .crm = 0, .opc2 = 1,
+ .access = PL1_RW, .writefn = vmsa_ttbr_write, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.ttbr1_s),
+ offsetof(CPUARMState, cp15.ttbr1_ns) } },
{ .name = "TCR_EL1", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .crn = 2, .crm = 0, .opc1 = 0, .opc2 = 2,
.access = PL1_RW, .writefn = vmsa_tcr_el1_write,
@@ -1883,11 +1885,13 @@ static const ARMCPRegInfo lpae_cp_reginfo[] = {
.fieldoffset = offsetof(CPUARMState, cp15.par_el1), .resetvalue = 0 },
{ .name = "TTBR0", .cp = 15, .crm = 2, .opc1 = 0,
.access = PL1_RW, .type = ARM_CP_64BIT | ARM_CP_NO_MIGRATE,
- .fieldoffset = offsetof(CPUARMState, cp15.ttbr0_el1),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.ttbr0_s),
+ offsetof(CPUARMState, cp15.ttbr0_ns) },
.writefn = vmsa_ttbr_write, .resetfn = arm_cp_reset_ignore },
{ .name = "TTBR1", .cp = 15, .crm = 2, .opc1 = 1,
.access = PL1_RW, .type = ARM_CP_64BIT | ARM_CP_NO_MIGRATE,
- .fieldoffset = offsetof(CPUARMState, cp15.ttbr1_el1),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.ttbr1_s),
+ offsetof(CPUARMState, cp15.ttbr1_ns) },
.writefn = vmsa_ttbr_write, .resetfn = arm_cp_reset_ignore },
REGINFO_SENTINEL
};
@@ -2341,6 +2345,10 @@ static const ARMCPRegInfo v8_el3_cp_reginfo[] = {
.opc0 = 3, .opc1 = 6, .crn = 1, .crm = 0, .opc2 = 0,
.access = PL3_RW, .raw_writefn = raw_write, .writefn = sctlr_write,
.fieldoffset = offsetof(CPUARMState, cp15.sctlr_el[3]) },
+ { .name = "TTBR0_EL3", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 6, .crn = 2, .crm = 0, .opc2 = 0,
+ .access = PL3_RW, .writefn = vmsa_ttbr_write, .resetvalue = 0,
+ .fieldoffset = offsetof(CPUARMState, cp15.ttbr0_el[3]) },
{ .name = "ELR_EL3", .state = ARM_CP_STATE_AA64,
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 6, .crn = 4, .crm = 0, .opc2 = 1,
@@ -4442,18 +4450,23 @@ static inline int check_ap(CPUARMState *env, int ap, int domain_prot,
static bool get_level1_table_address(CPUARMState *env, uint32_t *table,
uint32_t address)
{
+ /* We only get here if EL1 is running in AArch32. If EL3 is running in
+ * AArch32 there is a secure and non-secure instance of the translation
+ * table registers.
+ */
if (address & env->cp15.c2_mask) {
if ((env->cp15.c2_control & TTBCR_PD1)) {
/* Translation table walk disabled for TTBR1 */
return false;
}
- *table = env->cp15.ttbr1_el1 & 0xffffc000;
+ *table = A32_BANKED_CURRENT_REG_GET(env, ttbr1) & 0xffffc000;
} else {
if ((env->cp15.c2_control & TTBCR_PD0)) {
/* Translation table walk disabled for TTBR0 */
return false;
}
- *table = env->cp15.ttbr0_el1 & env->cp15.c2_base_mask;
+ *table = A32_BANKED_CURRENT_REG_GET(env, ttbr0) &
+ env->cp15.c2_base_mask;
}
*table |= (address >> 18) & 0x3ffc;
return true;
@@ -4758,7 +4771,7 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
* we will always flush the TLB any time the ASID is changed).
*/
if (ttbr_select == 0) {
- ttbr = env->cp15.ttbr0_el1;
+ ttbr = A32_BANKED_CURRENT_REG_GET(env, ttbr0);
epd = extract32(env->cp15.c2_control, 7, 1);
tsz = t0sz;
@@ -4770,7 +4783,7 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
granule_sz = 11;
}
} else {
- ttbr = env->cp15.ttbr1_el1;
+ ttbr = A32_BANKED_CURRENT_REG_GET(env, ttbr1);
epd = extract32(env->cp15.c2_control, 23, 1);
tsz = t1sz;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 17/26] target-arm: make TTBCR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (15 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 16/26] target-arm: make TTBR0/1 banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 18/26] target-arm: make DACR banked Greg Bellows
` (9 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Adds secure and non-secure bank register suport for TTBCR.
Added new struct to compartmentalize the TCR data and masks. Removed old
tcr/ttbcr data and added a 4 element array of the new structs in cp15. This
allows for one entry per EL. Added a CP register definition for TCR_EL3.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v10 -> v11
- Remove extraneous parens and fix comment spacing
v8 -> v9
- Removed get_phys_addr_lpae() AArch64 EL3 support.
- Replaced calls to ARM_CP_SECSTATE_TEST with direct access
- Reorganized the TCR data into a common TCR struct.
- Added raw_ptr() utility function for acquiring the TCR pointer from a reginfo
- Replaced accesses to tcr to use the new struct and utility function.
- Removed uses of A32_BANKED_CURRENT_REG_GET/SET with tcr
v5 -> v6
- Changed _el field variants to be array based
- Switch to use distinct CPREG secure flags
v4 -> v5
- Changed c2_mask updates to use the TTBCR cpreg bank flag for selcting the
secure bank instead of the A32_BANKED_CURRENT macro. This more accurately
chooses the correct bank matching that of the TTBCR being accessed.
---
target-arm/cpu.h | 11 +++++---
target-arm/helper.c | 72 ++++++++++++++++++++++++++++++++------------------
target-arm/internals.h | 6 ++---
3 files changed, 58 insertions(+), 31 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index efe7010..0eaf981 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -120,6 +120,12 @@ typedef struct ARMGenericTimer {
#define GTIMER_VIRT 1
#define NUM_GTIMERS 2
+typedef struct {
+ uint64_t raw_tcr;
+ uint32_t mask;
+ uint32_t base_mask;
+} TCR;
+
typedef struct CPUARMState {
/* Regs for current mode. */
uint32_t regs[16];
@@ -217,9 +223,8 @@ typedef struct CPUARMState {
};
uint64_t ttbr1_el[4];
};
- uint64_t c2_control; /* MMU translation table base control. */
- uint32_t c2_mask; /* MMU translation table base selection mask. */
- uint32_t c2_base_mask; /* MMU translation table base 0 mask. */
+ /* MMU translation table base control. */
+ TCR tcr_el[4];
uint32_t c2_data; /* MPU data cachable bits. */
uint32_t c2_insn; /* MPU instruction cachable bits. */
uint32_t c3; /* MMU domain access control register
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 908082c..7a2834e 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -136,6 +136,11 @@ static void raw_write(CPUARMState *env, const ARMCPRegInfo *ri,
}
}
+static void *raw_ptr(CPUARMState *env, const ARMCPRegInfo *ri)
+{
+ return (char *)env + ri->fieldoffset;
+}
+
static uint64_t read_raw_cp_reg(CPUARMState *env, const ARMCPRegInfo *ri)
{
/* Raw read of a coprocessor register (as needed for migration, etc). */
@@ -1560,6 +1565,7 @@ static const ARMCPRegInfo pmsav5_cp_reginfo[] = {
static void vmsa_ttbcr_raw_write(CPUARMState *env, const ARMCPRegInfo *ri,
uint64_t value)
{
+ TCR *tcr = raw_ptr(env, ri);
int maskshift = extract32(value, 0, 3);
if (!arm_feature(env, ARM_FEATURE_V8)) {
@@ -1578,14 +1584,15 @@ static void vmsa_ttbcr_raw_write(CPUARMState *env, const ARMCPRegInfo *ri,
}
}
- /* Note that we always calculate c2_mask and c2_base_mask, but
+ /* Update the masks corresponding to the the TCR bank being written
+ * Note that we always calculate mask and base_mask, but
* they are only used for short-descriptor tables (ie if EAE is 0);
- * for long-descriptor tables the TTBCR fields are used differently
- * and the c2_mask and c2_base_mask values are meaningless.
+ * for long-descriptor tables the TCR fields are used differently
+ * and the mask and base_mask values are meaningless.
*/
- raw_write(env, ri, value);
- env->cp15.c2_mask = ~(((uint32_t)0xffffffffu) >> maskshift);
- env->cp15.c2_base_mask = ~((uint32_t)0x3fffu >> maskshift);
+ tcr->raw_tcr = value;
+ tcr->mask = ~(((uint32_t)0xffffffffu) >> maskshift);
+ tcr->base_mask = ~((uint32_t)0x3fffu >> maskshift);
}
static void vmsa_ttbcr_write(CPUARMState *env, const ARMCPRegInfo *ri,
@@ -1604,19 +1611,25 @@ static void vmsa_ttbcr_write(CPUARMState *env, const ARMCPRegInfo *ri,
static void vmsa_ttbcr_reset(CPUARMState *env, const ARMCPRegInfo *ri)
{
- env->cp15.c2_base_mask = 0xffffc000u;
- raw_write(env, ri, 0);
- env->cp15.c2_mask = 0;
+ TCR *tcr = raw_ptr(env, ri);
+
+ /* Reset both the TCR as well as the masks corresponding to the bank of
+ * the TCR being reset.
+ */
+ tcr->raw_tcr = 0;
+ tcr->mask = 0;
+ tcr->base_mask = 0xffffc000u;
}
static void vmsa_tcr_el1_write(CPUARMState *env, const ARMCPRegInfo *ri,
uint64_t value)
{
ARMCPU *cpu = arm_env_get_cpu(env);
+ TCR *tcr = raw_ptr(env, ri);
/* For AArch64 the A1 bit could result in a change of ASID, so TLB flush. */
tlb_flush(CPU(cpu), 1);
- raw_write(env, ri, value);
+ tcr->raw_tcr = value;
}
static void vmsa_ttbr_write(CPUARMState *env, const ARMCPRegInfo *ri,
@@ -1659,11 +1672,12 @@ static const ARMCPRegInfo vmsa_cp_reginfo[] = {
.opc0 = 3, .crn = 2, .crm = 0, .opc1 = 0, .opc2 = 2,
.access = PL1_RW, .writefn = vmsa_tcr_el1_write,
.resetfn = vmsa_ttbcr_reset, .raw_writefn = raw_write,
- .fieldoffset = offsetof(CPUARMState, cp15.c2_control) },
+ .fieldoffset = offsetof(CPUARMState, cp15.tcr_el[1]) },
{ .name = "TTBCR", .cp = 15, .crn = 2, .crm = 0, .opc1 = 0, .opc2 = 2,
.access = PL1_RW, .type = ARM_CP_NO_MIGRATE, .writefn = vmsa_ttbcr_write,
.resetfn = arm_cp_reset_ignore, .raw_writefn = vmsa_ttbcr_raw_write,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.c2_control) },
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.tcr_el[3]),
+ offsetoflow32(CPUARMState, cp15.tcr_el[1])} },
/* 64-bit FAR; this entry also gives us the AArch32 DFAR */
{ .name = "FAR_EL1", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .crn = 6, .crm = 0, .opc1 = 0, .opc2 = 0,
@@ -2349,6 +2363,11 @@ static const ARMCPRegInfo v8_el3_cp_reginfo[] = {
.opc0 = 3, .opc1 = 6, .crn = 2, .crm = 0, .opc2 = 0,
.access = PL3_RW, .writefn = vmsa_ttbr_write, .resetvalue = 0,
.fieldoffset = offsetof(CPUARMState, cp15.ttbr0_el[3]) },
+ { .name = "TCR_EL3", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 6, .crn = 2, .crm = 0, .opc2 = 2,
+ .access = PL3_RW, .writefn = vmsa_tcr_el1_write,
+ .resetfn = vmsa_ttbcr_reset, .raw_writefn = raw_write,
+ .fieldoffset = offsetof(CPUARMState, cp15.tcr_el[3]) },
{ .name = "ELR_EL3", .state = ARM_CP_STATE_AA64,
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 6, .crn = 4, .crm = 0, .opc2 = 1,
@@ -4450,23 +4469,25 @@ static inline int check_ap(CPUARMState *env, int ap, int domain_prot,
static bool get_level1_table_address(CPUARMState *env, uint32_t *table,
uint32_t address)
{
+ /* Get the TCR bank based on our security state */
+ TCR *tcr = &env->cp15.tcr_el[arm_is_secure(env) ? 3 : 1];
+
/* We only get here if EL1 is running in AArch32. If EL3 is running in
* AArch32 there is a secure and non-secure instance of the translation
* table registers.
*/
- if (address & env->cp15.c2_mask) {
- if ((env->cp15.c2_control & TTBCR_PD1)) {
+ if (address & tcr->mask) {
+ if (tcr->raw_tcr & TTBCR_PD1) {
/* Translation table walk disabled for TTBR1 */
return false;
}
*table = A32_BANKED_CURRENT_REG_GET(env, ttbr1) & 0xffffc000;
} else {
- if ((env->cp15.c2_control & TTBCR_PD0)) {
+ if (tcr->raw_tcr & TTBCR_PD0) {
/* Translation table walk disabled for TTBR0 */
return false;
}
- *table = A32_BANKED_CURRENT_REG_GET(env, ttbr0) &
- env->cp15.c2_base_mask;
+ *table = A32_BANKED_CURRENT_REG_GET(env, ttbr0) & tcr->base_mask;
}
*table |= (address >> 18) & 0x3ffc;
return true;
@@ -4720,13 +4741,14 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
int32_t granule_sz = 9;
int32_t va_size = 32;
int32_t tbi = 0;
+ TCR *tcr = &env->cp15.tcr_el[arm_is_secure(env) ? 3 : 1];
if (arm_el_is_aa64(env, 1)) {
va_size = 64;
if (extract64(address, 55, 1))
- tbi = extract64(env->cp15.c2_control, 38, 1);
+ tbi = extract64(tcr->raw_tcr, 38, 1);
else
- tbi = extract64(env->cp15.c2_control, 37, 1);
+ tbi = extract64(tcr->raw_tcr, 37, 1);
tbi *= 8;
}
@@ -4735,12 +4757,12 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
* This is a Non-secure PL0/1 stage 1 translation, so controlled by
* TTBCR/TTBR0/TTBR1 in accordance with ARM ARM DDI0406C table B-32:
*/
- uint32_t t0sz = extract32(env->cp15.c2_control, 0, 6);
+ uint32_t t0sz = extract32(tcr->raw_tcr, 0, 6);
if (arm_el_is_aa64(env, 1)) {
t0sz = MIN(t0sz, 39);
t0sz = MAX(t0sz, 16);
}
- uint32_t t1sz = extract32(env->cp15.c2_control, 16, 6);
+ uint32_t t1sz = extract32(tcr->raw_tcr, 16, 6);
if (arm_el_is_aa64(env, 1)) {
t1sz = MIN(t1sz, 39);
t1sz = MAX(t1sz, 16);
@@ -4772,10 +4794,10 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
*/
if (ttbr_select == 0) {
ttbr = A32_BANKED_CURRENT_REG_GET(env, ttbr0);
- epd = extract32(env->cp15.c2_control, 7, 1);
+ epd = extract32(tcr->raw_tcr, 7, 1);
tsz = t0sz;
- tg = extract32(env->cp15.c2_control, 14, 2);
+ tg = extract32(tcr->raw_tcr, 14, 2);
if (tg == 1) { /* 64KB pages */
granule_sz = 13;
}
@@ -4784,10 +4806,10 @@ static int get_phys_addr_lpae(CPUARMState *env, target_ulong address,
}
} else {
ttbr = A32_BANKED_CURRENT_REG_GET(env, ttbr1);
- epd = extract32(env->cp15.c2_control, 23, 1);
+ epd = extract32(tcr->raw_tcr, 23, 1);
tsz = t1sz;
- tg = extract32(env->cp15.c2_control, 30, 2);
+ tg = extract32(tcr->raw_tcr, 30, 2);
if (tg == 3) { /* 64KB pages */
granule_sz = 13;
}
diff --git a/target-arm/internals.h b/target-arm/internals.h
index 2dff4ff..bb171a7 100644
--- a/target-arm/internals.h
+++ b/target-arm/internals.h
@@ -153,9 +153,9 @@ static inline void update_spsel(CPUARMState *env, uint32_t imm)
*/
static inline bool extended_addresses_enabled(CPUARMState *env)
{
- return arm_el_is_aa64(env, 1)
- || ((arm_feature(env, ARM_FEATURE_LPAE)
- && (env->cp15.c2_control & TTBCR_EAE)));
+ TCR *tcr = &env->cp15.tcr_el[arm_is_secure(env) ? 3 : 1];
+ return arm_el_is_aa64(env, 1) ||
+ (arm_feature(env, ARM_FEATURE_LPAE) && (tcr->raw_tcr & TTBCR_EAE));
}
/* Valid Syndrome Register EC field values */
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 18/26] target-arm: make DACR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (16 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 17/26] target-arm: make TTBCR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 19/26] target-arm: make IFSR banked Greg Bellows
` (8 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
DACR has a secure and a non-secure instance. Adds definition for DACR32_EL2.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Added definition for DACR32_EL2
- Changed dacr cp15 fields to uint64_t
---
hw/arm/pxa2xx.c | 2 +-
target-arm/cpu.h | 13 +++++++++++--
target-arm/helper.c | 28 ++++++++++++++++++----------
3 files changed, 30 insertions(+), 13 deletions(-)
diff --git a/hw/arm/pxa2xx.c b/hw/arm/pxa2xx.c
index 2b00b59..8967cc4 100644
--- a/hw/arm/pxa2xx.c
+++ b/hw/arm/pxa2xx.c
@@ -276,7 +276,7 @@ static void pxa2xx_pwrmode_write(CPUARMState *env, const ARMCPRegInfo *ri,
s->cpu->env.cp15.sctlr_ns = 0;
s->cpu->env.cp15.c1_coproc = 0;
s->cpu->env.cp15.ttbr0_el[1] = 0;
- s->cpu->env.cp15.c3 = 0;
+ s->cpu->env.cp15.dacr_ns = 0;
s->pm_regs[PSSR >> 2] |= 0x8; /* Set STS */
s->pm_regs[RCSR >> 2] |= 0x8; /* Set GPR */
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 0eaf981..1906fc1 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -227,8 +227,17 @@ typedef struct CPUARMState {
TCR tcr_el[4];
uint32_t c2_data; /* MPU data cachable bits. */
uint32_t c2_insn; /* MPU instruction cachable bits. */
- uint32_t c3; /* MMU domain access control register
- MPU write buffer control. */
+ union { /* MMU domain access control register
+ * MPU write buffer control.
+ */
+ struct {
+ uint64_t dacr_ns;
+ uint64_t dacr_s;
+ };
+ struct {
+ uint64_t dacr32_el2;
+ };
+ };
uint32_t pmsav5_data_ap; /* PMSAv5 MPU data access permissions */
uint32_t pmsav5_insn_ap; /* PMSAv5 MPU insn access permissions */
uint64_t hcr_el2; /* Hypervisor configuration register */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 7a2834e..85c28b7 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -440,10 +440,12 @@ static const ARMCPRegInfo not_v8_cp_reginfo[] = {
* definitions that don't use CP_ANY wildcards (mostly in v8_cp_reginfo[]).
*/
/* MMU Domain access control / MPU write buffer control */
- { .name = "DACR", .cp = 15,
- .crn = 3, .crm = CP_ANY, .opc1 = CP_ANY, .opc2 = CP_ANY,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.c3),
- .resetvalue = 0, .writefn = dacr_write, .raw_writefn = raw_write, },
+ { .name = "DACR",
+ .cp = 15, .opc1 = CP_ANY, .crn = 3, .crm = CP_ANY, .opc2 = CP_ANY,
+ .access = PL1_RW, .resetvalue = 0,
+ .writefn = dacr_write, .raw_writefn = raw_write,
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.dacr_s),
+ offsetoflow32(CPUARMState, cp15.dacr_ns) } },
/* ??? This covers not just the impdef TLB lockdown registers but also
* some v7VMSA registers relating to TEX remap, so it is overly broad.
*/
@@ -2257,10 +2259,11 @@ static const ARMCPRegInfo v8_cp_reginfo[] = {
{ .name = "DCCISW", .cp = 15, .opc1 = 0, .crn = 7, .crm = 14, .opc2 = 2,
.type = ARM_CP_NOP, .access = PL1_W },
/* MMU Domain access control / MPU write buffer control */
- { .name = "DACR", .cp = 15,
- .opc1 = 0, .crn = 3, .crm = 0, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.c3),
- .resetvalue = 0, .writefn = dacr_write, .raw_writefn = raw_write, },
+ { .name = "DACR", .cp = 15, .opc1 = 0, .crn = 3, .crm = 0, .opc2 = 0,
+ .access = PL1_RW, .resetvalue = 0,
+ .writefn = dacr_write, .raw_writefn = raw_write,
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.dacr_s),
+ offsetoflow32(CPUARMState, cp15.dacr_ns) } },
{ .name = "ELR_EL1", .state = ARM_CP_STATE_AA64,
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 0, .crn = 4, .crm = 0, .opc2 = 1,
@@ -2330,6 +2333,11 @@ static const ARMCPRegInfo v8_el2_cp_reginfo[] = {
.opc0 = 3, .opc1 = 4, .crn = 1, .crm = 1, .opc2 = 0,
.access = PL2_RW, .fieldoffset = offsetof(CPUARMState, cp15.hcr_el2),
.writefn = hcr_write },
+ { .name = "DACR32_EL2", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 4, .crn = 3, .crm = 0, .opc2 = 0,
+ .access = PL2_RW, .resetvalue = 0,
+ .writefn = dacr_write, .raw_writefn = raw_write,
+ .fieldoffset = offsetof(CPUARMState, cp15.dacr32_el2) },
{ .name = "ELR_EL2", .state = ARM_CP_STATE_AA64,
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 4, .crn = 4, .crm = 0, .opc2 = 1,
@@ -4517,7 +4525,7 @@ static int get_phys_addr_v5(CPUARMState *env, uint32_t address, int access_type,
desc = ldl_phys(cs->as, table);
type = (desc & 3);
domain = (desc >> 5) & 0x0f;
- domain_prot = (env->cp15.c3 >> (domain * 2)) & 3;
+ domain_prot = (A32_BANKED_CURRENT_REG_GET(env, dacr) >> (domain * 2)) & 3;
if (type == 0) {
/* Section translation fault. */
code = 5;
@@ -4629,7 +4637,7 @@ static int get_phys_addr_v6(CPUARMState *env, uint32_t address, int access_type,
/* Page or Section. */
domain = (desc >> 5) & 0x0f;
}
- domain_prot = (env->cp15.c3 >> (domain * 2)) & 3;
+ domain_prot = (A32_BANKED_CURRENT_REG_GET(env, dacr) >> (domain * 2)) & 3;
if (domain_prot == 0 || domain_prot == 2) {
if (type != 1) {
code = 9; /* Section domain fault. */
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 19/26] target-arm: make IFSR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (17 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 18/26] target-arm: make DACR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 20/26] target-arm: make DFSR banked Greg Bellows
` (7 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
IFSR has a secure and a non-secure instance. Adds IFSR32_EL2 definition and
storage.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Added definition for IFSR32_EL2
- Changed ifsr cp15 fields to uint64_t
---
target-arm/cpu.h | 10 +++++++++-
target-arm/helper.c | 13 +++++++++----
2 files changed, 18 insertions(+), 5 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 1906fc1..e8bb057 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -242,7 +242,15 @@ typedef struct CPUARMState {
uint32_t pmsav5_insn_ap; /* PMSAv5 MPU insn access permissions */
uint64_t hcr_el2; /* Hypervisor configuration register */
uint64_t scr_el3; /* Secure configuration register. */
- uint32_t ifsr_el2; /* Fault status registers. */
+ union { /* Fault status registers. */
+ struct {
+ uint64_t ifsr_ns;
+ uint64_t ifsr_s;
+ };
+ struct {
+ uint64_t ifsr32_el2;
+ };
+ };
uint64_t esr_el[4];
uint32_t c6_region[8]; /* MPU base/size registers. */
uint64_t far_el[4]; /* Fault address registers. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 85c28b7..1ed7bd2 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -1654,8 +1654,9 @@ static const ARMCPRegInfo vmsa_cp_reginfo[] = {
.fieldoffset = offsetoflow32(CPUARMState, cp15.esr_el[1]),
.resetfn = arm_cp_reset_ignore, },
{ .name = "IFSR", .cp = 15, .crn = 5, .crm = 0, .opc1 = 0, .opc2 = 1,
- .access = PL1_RW,
- .fieldoffset = offsetof(CPUARMState, cp15.ifsr_el2), .resetvalue = 0, },
+ .access = PL1_RW, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.ifsr_s),
+ offsetoflow32(CPUARMState, cp15.ifsr_ns) } },
{ .name = "ESR_EL1", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .crn = 5, .crm = 2, .opc1 = 0, .opc2 = 0,
.access = PL1_RW,
@@ -2347,6 +2348,10 @@ static const ARMCPRegInfo v8_el2_cp_reginfo[] = {
.type = ARM_CP_NO_MIGRATE,
.opc0 = 3, .opc1 = 4, .crn = 5, .crm = 2, .opc2 = 0,
.access = PL2_RW, .fieldoffset = offsetof(CPUARMState, cp15.esr_el[2]) },
+ { .name = "IFSR32_EL2", .state = ARM_CP_STATE_AA64,
+ .opc0 = 3, .opc1 = 4, .crn = 5, .crm = 0, .opc2 = 1,
+ .access = PL2_RW, .resetvalue = 0,
+ .fieldoffset = offsetof(CPUARMState, cp15.ifsr32_el2) },
{ .name = "FAR_EL2", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .opc1 = 4, .crn = 6, .crm = 0, .opc2 = 0,
.access = PL2_RW, .fieldoffset = offsetof(CPUARMState, cp15.far_el[2]) },
@@ -4323,11 +4328,11 @@ void arm_cpu_do_interrupt(CPUState *cs)
env->exception.fsr = 2;
/* Fall through to prefetch abort. */
case EXCP_PREFETCH_ABORT:
- env->cp15.ifsr_el2 = env->exception.fsr;
+ A32_BANKED_CURRENT_REG_SET(env, ifsr, env->exception.fsr);
env->cp15.far_el[1] = deposit64(env->cp15.far_el[1], 32, 32,
env->exception.vaddress);
qemu_log_mask(CPU_LOG_INT, "...with IFSR 0x%x IFAR 0x%x\n",
- env->cp15.ifsr_el2, (uint32_t)env->exception.vaddress);
+ env->exception.fsr, (uint32_t)env->exception.vaddress);
new_mode = ARM_CPU_MODE_ABT;
addr = 0x0c;
mask = CPSR_A | CPSR_I;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 20/26] target-arm: make DFSR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (18 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 19/26] target-arm: make IFSR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 21/26] target-arm: make IFAR/DFAR banked Greg Bellows
` (6 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
DFSR has a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v3 -> v4
- Reverted esr/dfsr back to array-based notation as a union with v7 naming.
---
target-arm/cpu.h | 10 +++++++++-
target-arm/helper.c | 7 ++++---
2 files changed, 13 insertions(+), 4 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index e8bb057..29870bd 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -251,7 +251,15 @@ typedef struct CPUARMState {
uint64_t ifsr32_el2;
};
};
- uint64_t esr_el[4];
+ union {
+ struct {
+ uint64_t _unused_dfsr;
+ uint64_t dfsr_ns;
+ uint64_t hsr;
+ uint64_t dfsr_s;
+ };
+ uint64_t esr_el[4];
+ };
uint32_t c6_region[8]; /* MPU base/size registers. */
uint64_t far_el[4]; /* Fault address registers. */
uint64_t par_el1; /* Translation result. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 1ed7bd2..eb0f8b4 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -1651,7 +1651,8 @@ static void vmsa_ttbr_write(CPUARMState *env, const ARMCPRegInfo *ri,
static const ARMCPRegInfo vmsa_cp_reginfo[] = {
{ .name = "DFSR", .cp = 15, .crn = 5, .crm = 0, .opc1 = 0, .opc2 = 0,
.access = PL1_RW, .type = ARM_CP_NO_MIGRATE,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.esr_el[1]),
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.dfsr_s),
+ offsetoflow32(CPUARMState, cp15.dfsr_ns) },
.resetfn = arm_cp_reset_ignore, },
{ .name = "IFSR", .cp = 15, .crn = 5, .crm = 0, .opc1 = 0, .opc2 = 1,
.access = PL1_RW, .resetvalue = 0,
@@ -4339,11 +4340,11 @@ void arm_cpu_do_interrupt(CPUState *cs)
offset = 4;
break;
case EXCP_DATA_ABORT:
- env->cp15.esr_el[1] = env->exception.fsr;
+ A32_BANKED_CURRENT_REG_SET(env, dfsr, env->exception.fsr);
env->cp15.far_el[1] = deposit64(env->cp15.far_el[1], 0, 32,
env->exception.vaddress);
qemu_log_mask(CPU_LOG_INT, "...with DFSR 0x%x DFAR 0x%x\n",
- (uint32_t)env->cp15.esr_el[1],
+ env->exception.fsr,
(uint32_t)env->exception.vaddress);
new_mode = ARM_CPU_MODE_ABT;
addr = 0x10;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 21/26] target-arm: make IFAR/DFAR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (19 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 20/26] target-arm: make DFSR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 22/26] target-arm: make PAR banked Greg Bellows
` (5 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
IFAR and DFAR have a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Reordered CP register component order
- Removed extra semicolon
v3 -> v4
- Revert to array-based notation of far_el in combination with v7 naming
---
target-arm/cpu.c | 2 +-
target-arm/cpu.h | 19 ++++++++++++++++++-
target-arm/helper.c | 16 +++++++++-------
3 files changed, 28 insertions(+), 9 deletions(-)
diff --git a/target-arm/cpu.c b/target-arm/cpu.c
index fdb7b35..d3db279 100644
--- a/target-arm/cpu.c
+++ b/target-arm/cpu.c
@@ -552,7 +552,7 @@ static void arm1026_initfn(Object *obj)
ARMCPRegInfo ifar = {
.name = "IFAR", .cp = 15, .crn = 6, .crm = 0, .opc1 = 0, .opc2 = 1,
.access = PL1_RW,
- .fieldoffset = offsetofhigh32(CPUARMState, cp15.far_el[1]),
+ .fieldoffset = offsetof(CPUARMState, cp15.ifar_ns),
.resetvalue = 0
};
define_one_arm_cp_reg(cpu, &ifar);
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 29870bd..52d5719 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -261,7 +261,24 @@ typedef struct CPUARMState {
uint64_t esr_el[4];
};
uint32_t c6_region[8]; /* MPU base/size registers. */
- uint64_t far_el[4]; /* Fault address registers. */
+ union { /* Fault address registers. */
+ struct {
+ uint64_t _unused_far0;
+#ifdef HOST_WORDS_BIGENDIAN
+ uint32_t ifar_ns;
+ uint32_t dfar_ns;
+ uint32_t ifar_s;
+ uint32_t dfar_s;
+#else
+ uint32_t dfar_ns;
+ uint32_t ifar_ns;
+ uint32_t dfar_s;
+ uint32_t ifar_s;
+#endif
+ uint64_t _unused_far3;
+ };
+ uint64_t far_el[4];
+ };
uint64_t par_el1; /* Translation result. */
uint32_t c9_insn; /* Cache lockdown registers. */
uint32_t c9_data;
diff --git a/target-arm/helper.c b/target-arm/helper.c
index eb0f8b4..318fb74 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -559,7 +559,8 @@ static const ARMCPRegInfo v6_cp_reginfo[] = {
.access = PL0_W, .type = ARM_CP_NOP },
{ .name = "IFAR", .cp = 15, .crn = 6, .crm = 0, .opc1 = 0, .opc2 = 2,
.access = PL1_RW,
- .fieldoffset = offsetofhigh32(CPUARMState, cp15.far_el[1]),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.ifar_s),
+ offsetof(CPUARMState, cp15.ifar_ns) },
.resetvalue = 0, },
/* Watchpoint Fault Address Register : should actually only be present
* for 1136, 1176, 11MPCore.
@@ -1682,11 +1683,14 @@ static const ARMCPRegInfo vmsa_cp_reginfo[] = {
.resetfn = arm_cp_reset_ignore, .raw_writefn = vmsa_ttbcr_raw_write,
.bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.tcr_el[3]),
offsetoflow32(CPUARMState, cp15.tcr_el[1])} },
- /* 64-bit FAR; this entry also gives us the AArch32 DFAR */
- { .name = "FAR_EL1", .state = ARM_CP_STATE_BOTH,
+ { .name = "FAR_EL1", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .crn = 6, .crm = 0, .opc1 = 0, .opc2 = 0,
.access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.far_el[1]),
.resetvalue = 0, },
+ { .name = "DFAR", .cp = 15, .opc1 = 0, .crn = 6, .crm = 0, .opc2 = 0,
+ .access = PL1_RW, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.dfar_s),
+ offsetof(CPUARMState, cp15.dfar_ns) } },
REGINFO_SENTINEL
};
@@ -4330,8 +4334,7 @@ void arm_cpu_do_interrupt(CPUState *cs)
/* Fall through to prefetch abort. */
case EXCP_PREFETCH_ABORT:
A32_BANKED_CURRENT_REG_SET(env, ifsr, env->exception.fsr);
- env->cp15.far_el[1] = deposit64(env->cp15.far_el[1], 32, 32,
- env->exception.vaddress);
+ A32_BANKED_CURRENT_REG_SET(env, ifar, env->exception.vaddress);
qemu_log_mask(CPU_LOG_INT, "...with IFSR 0x%x IFAR 0x%x\n",
env->exception.fsr, (uint32_t)env->exception.vaddress);
new_mode = ARM_CPU_MODE_ABT;
@@ -4341,8 +4344,7 @@ void arm_cpu_do_interrupt(CPUState *cs)
break;
case EXCP_DATA_ABORT:
A32_BANKED_CURRENT_REG_SET(env, dfsr, env->exception.fsr);
- env->cp15.far_el[1] = deposit64(env->cp15.far_el[1], 0, 32,
- env->exception.vaddress);
+ A32_BANKED_CURRENT_REG_SET(env, dfar, env->exception.vaddress);
qemu_log_mask(CPU_LOG_INT, "...with DFSR 0x%x DFAR 0x%x\n",
env->exception.fsr,
(uint32_t)env->exception.vaddress);
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 22/26] target-arm: make PAR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (20 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 21/26] target-arm: make IFAR/DFAR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 23/26] target-arm: make VBAR banked Greg Bellows
` (4 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
PAR has a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Cleaned-up ats_write() to only call A32_BANKED_CURRENT_REG_SET() once at the
endof the function.
- Revert unnecessary CPreg definition changes
v5 -> v6
- Changed _el field variants to be array based
v3 -> v4
- Fix par union/structure definition
---
target-arm/cpu.h | 10 +++++++++-
target-arm/helper.c | 23 +++++++++++++----------
2 files changed, 22 insertions(+), 11 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 52d5719..2f8d607 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -279,7 +279,15 @@ typedef struct CPUARMState {
};
uint64_t far_el[4];
};
- uint64_t par_el1; /* Translation result. */
+ union { /* Translation result. */
+ struct {
+ uint64_t _unused_par_0;
+ uint64_t par_ns;
+ uint64_t _unused_par_1;
+ uint64_t par_s;
+ };
+ uint64_t par_el[4];
+ };
uint32_t c9_insn; /* Cache lockdown registers. */
uint32_t c9_data;
uint64_t c9_pmcr; /* performance monitor control register */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 318fb74..081c00e 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -1404,6 +1404,7 @@ static void ats_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t value)
int prot;
int ret, is_user = ri->opc2 & 2;
int access_type = ri->opc2 & 1;
+ uint64_t par64;
ret = get_phys_addr(env, value, access_type, is_user,
&phys_addr, &prot, &page_size);
@@ -1412,7 +1413,7 @@ static void ats_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t value)
* translation table format, but with WnR always clear.
* Convert it to a 64-bit PAR.
*/
- uint64_t par64 = (1 << 11); /* LPAE bit always set */
+ par64 = (1 << 11); /* LPAE bit always set */
if (ret == 0) {
par64 |= phys_addr & ~0xfffULL;
/* We don't set the ATTR or SH fields in the PAR. */
@@ -1424,7 +1425,6 @@ static void ats_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t value)
* fault.
*/
}
- env->cp15.par_el1 = par64;
} else {
/* ret is a DFSR/IFSR value for the short descriptor
* translation table format (with WnR always clear).
@@ -1434,23 +1434,25 @@ static void ats_write(CPUARMState *env, const ARMCPRegInfo *ri, uint64_t value)
/* We do not set any attribute bits in the PAR */
if (page_size == (1 << 24)
&& arm_feature(env, ARM_FEATURE_V7)) {
- env->cp15.par_el1 = (phys_addr & 0xff000000) | 1 << 1;
+ par64 = (phys_addr & 0xff000000) | (1 << 1);
} else {
- env->cp15.par_el1 = phys_addr & 0xfffff000;
+ par64 = phys_addr & 0xfffff000;
}
} else {
- env->cp15.par_el1 = ((ret & (1 << 10)) >> 5) |
- ((ret & (1 << 12)) >> 6) |
- ((ret & 0xf) << 1) | 1;
+ par64 = ((ret & (1 << 10)) >> 5) | ((ret & (1 << 12)) >> 6) |
+ ((ret & 0xf) << 1) | 1;
}
}
+
+ A32_BANKED_CURRENT_REG_SET(env, par, par64);
}
#endif
static const ARMCPRegInfo vapa_cp_reginfo[] = {
{ .name = "PAR", .cp = 15, .crn = 7, .crm = 4, .opc1 = 0, .opc2 = 0,
.access = PL1_RW, .resetvalue = 0,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.par_el1),
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.par_s),
+ offsetoflow32(CPUARMState, cp15.par_ns) },
.writefn = par_write },
#ifndef CONFIG_USER_ONLY
{ .name = "ATS", .cp = 15, .crn = 7, .crm = 8, .opc1 = 0, .opc2 = CP_ANY,
@@ -1903,8 +1905,9 @@ static const ARMCPRegInfo lpae_cp_reginfo[] = {
.access = PL1_RW, .type = ARM_CP_CONST | ARM_CP_OVERRIDE,
.resetvalue = 0 },
{ .name = "PAR", .cp = 15, .crm = 7, .opc1 = 0,
- .access = PL1_RW, .type = ARM_CP_64BIT,
- .fieldoffset = offsetof(CPUARMState, cp15.par_el1), .resetvalue = 0 },
+ .access = PL1_RW, .type = ARM_CP_64BIT, .resetvalue = 0,
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.par_s),
+ offsetof(CPUARMState, cp15.par_ns)} },
{ .name = "TTBR0", .cp = 15, .crm = 2, .opc1 = 0,
.access = PL1_RW, .type = ARM_CP_64BIT | ARM_CP_NO_MIGRATE,
.bank_fieldoffsets = { offsetof(CPUARMState, cp15.ttbr0_s),
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 23/26] target-arm: make VBAR banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (21 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 22/26] target-arm: make PAR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 24/26] target-arm: make c13 cp regs banked (FCSEIDR, ...) Greg Bellows
` (3 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
When EL3 is running in Aarch32 (or ARMv7 with Security Extensions)
VBAR has a secure and a non-secure instance, which are mapped to
VBAR_EL1 and VBAR_EL3.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Revert unnecessary CPreg definition changes
v5 -> v6
- Changed _el field variants to be array based
- Merged VBAR and VBAR_EL1 reginfo entries
v3 -> v4
- Fix vbar union/structure definition
- Revert back to array-based vbar definition combined with v7 naming
---
target-arm/cpu.h | 10 +++++++++-
target-arm/helper.c | 5 +++--
2 files changed, 12 insertions(+), 3 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index 2f8d607..fc64497 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -297,7 +297,15 @@ typedef struct CPUARMState {
uint32_t c9_pmuserenr; /* perf monitor user enable */
uint32_t c9_pminten; /* perf monitor interrupt enables */
uint64_t mair_el1;
- uint64_t vbar_el[4]; /* vector base address register */
+ union { /* vector base address register */
+ struct {
+ uint64_t _unused_vbar;
+ uint64_t vbar_ns;
+ uint64_t hvbar;
+ uint64_t vbar_s;
+ };
+ uint64_t vbar_el[4];
+ };
uint32_t mvbar; /* (monitor) vector base address register */
uint32_t c13_fcse; /* FCSE PID. */
uint64_t contextidr_el1; /* Context ID. */
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 081c00e..69f2e68 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -911,7 +911,8 @@ static const ARMCPRegInfo v7_cp_reginfo[] = {
{ .name = "VBAR", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .crn = 12, .crm = 0, .opc1 = 0, .opc2 = 0,
.access = PL1_RW, .writefn = vbar_write,
- .fieldoffset = offsetof(CPUARMState, cp15.vbar_el[1]),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.vbar_s),
+ offsetof(CPUARMState, cp15.vbar_ns) },
.resetvalue = 0 },
{ .name = "CCSIDR", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .crn = 0, .crm = 0, .opc1 = 1, .opc2 = 0,
@@ -4401,7 +4402,7 @@ void arm_cpu_do_interrupt(CPUState *cs)
* This register is only followed in non-monitor mode, and is banked.
* Note: only bits 31:5 are valid.
*/
- addr += env->cp15.vbar_el[1];
+ addr += A32_BANKED_CURRENT_REG_GET(env, vbar);
}
if ((env->uncached_cpsr & CPSR_M) == ARM_CPU_MODE_MON) {
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 24/26] target-arm: make c13 cp regs banked (FCSEIDR, ...)
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (22 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 23/26] target-arm: make VBAR banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 25/26] target-arm: make MAIR0/1 banked Greg Bellows
` (2 subsequent siblings)
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
FCSEIDR, CONTEXTIDR, TPIDRURW, TPIDRURO and TPIDRPRW have a secure
and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Changed contextidr structure definition to have 4 uint64_t fields.
- Broke up secure/non-secure CONTEXTIDR defs so the secure instance can be
properly migrated and reset.
- Broke up secure/non-secure FCSEIDR defs.
- Reversed CP register field reordering
- Reversed white-space changes
v6 -> v7
- Fix linux-user/arm/target-cpu.h to use array based tpidr_el.
- Fix linux-user/main.c to use array based tpidrro_el.
- Remove tab identified by checkpatch failure.
- FIx linux-user/aarch64/target_cpu.h to use array based tpidr_el.
v5 -> v6
- Changed _el field variants to be array based
- Rework data layout for correct aliasing
- Merged CONTEXTIDR and CONTEXTIDR_EL1 reginfo entries
v3 -> v4
- Fix tpidrprw mapping
---
linux-user/aarch64/target_cpu.h | 2 +-
linux-user/arm/target_cpu.h | 2 +-
linux-user/main.c | 2 +-
target-arm/cpu.h | 36 +++++++++++++++++++++----
target-arm/helper.c | 58 ++++++++++++++++++++++++++++++++---------
target-arm/op_helper.c | 2 +-
6 files changed, 80 insertions(+), 22 deletions(-)
diff --git a/linux-user/aarch64/target_cpu.h b/linux-user/aarch64/target_cpu.h
index 21560ef..b5593dc 100644
--- a/linux-user/aarch64/target_cpu.h
+++ b/linux-user/aarch64/target_cpu.h
@@ -32,7 +32,7 @@ static inline void cpu_set_tls(CPUARMState *env, target_ulong newtls)
/* Note that AArch64 Linux keeps the TLS pointer in TPIDR; this is
* different from AArch32 Linux, which uses TPIDRRO.
*/
- env->cp15.tpidr_el0 = newtls;
+ env->cp15.tpidr_el[0] = newtls;
}
#endif
diff --git a/linux-user/arm/target_cpu.h b/linux-user/arm/target_cpu.h
index 39d65b6..d8a534d 100644
--- a/linux-user/arm/target_cpu.h
+++ b/linux-user/arm/target_cpu.h
@@ -29,7 +29,7 @@ static inline void cpu_clone_regs(CPUARMState *env, target_ulong newsp)
static inline void cpu_set_tls(CPUARMState *env, target_ulong newtls)
{
- env->cp15.tpidrro_el0 = newtls;
+ env->cp15.tpidrro_el[0] = newtls;
}
#endif
diff --git a/linux-user/main.c b/linux-user/main.c
index 5c14c1e..186ee4d 100644
--- a/linux-user/main.c
+++ b/linux-user/main.c
@@ -564,7 +564,7 @@ do_kernel_trap(CPUARMState *env)
end_exclusive();
break;
case 0xffff0fe0: /* __kernel_get_tls */
- env->regs[0] = env->cp15.tpidrro_el0;
+ env->regs[0] = env->cp15.tpidrro_el[0];
break;
case 0xffff0f60: /* __kernel_cmpxchg64 */
arm_kernel_cmpxchg64_helper(env);
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index fc64497..a1fefe4 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -307,11 +307,37 @@ typedef struct CPUARMState {
uint64_t vbar_el[4];
};
uint32_t mvbar; /* (monitor) vector base address register */
- uint32_t c13_fcse; /* FCSE PID. */
- uint64_t contextidr_el1; /* Context ID. */
- uint64_t tpidr_el0; /* User RW Thread register. */
- uint64_t tpidrro_el0; /* User RO Thread register. */
- uint64_t tpidr_el1; /* Privileged Thread register. */
+ struct { /* FCSE PID. */
+ uint32_t fcseidr_ns;
+ uint32_t fcseidr_s;
+ };
+ union { /* Context ID. */
+ struct {
+ uint64_t _unused_contextidr_0;
+ uint64_t contextidr_ns;
+ uint64_t _unused_contextidr_1;
+ uint64_t contextidr_s;
+ };
+ uint64_t contextidr_el[4];
+ };
+ union { /* User RW Thread register. */
+ struct {
+ uint64_t tpidrurw_ns;
+ uint64_t tpidrprw_ns;
+ uint64_t htpidr;
+ uint64_t _tpidr_el3;
+ };
+ uint64_t tpidr_el[4];
+ };
+ /* The secure banks of these registers don't map anywhere */
+ uint64_t tpidrurw_s;
+ uint64_t tpidrprw_s;
+ uint64_t tpidruro_s;
+
+ union { /* User RO Thread register. */
+ uint64_t tpidruro_ns;
+ uint64_t tpidrro_el[1];
+ };
uint64_t c14_cntfrq; /* Counter Frequency register */
uint64_t c14_cntkctl; /* Timer Control register */
ARMGenericTimer c14_timer[NUM_GTIMERS];
diff --git a/target-arm/helper.c b/target-arm/helper.c
index 69f2e68..b611573 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -424,13 +424,36 @@ static void tlbimvaa_is_write(CPUARMState *env, const ARMCPRegInfo *ri,
}
static const ARMCPRegInfo cp_reginfo[] = {
- { .name = "FCSEIDR", .cp = 15, .crn = 13, .crm = 0, .opc1 = 0, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.c13_fcse),
+ /* Define the secure and non-secure FCSE identifier CP registers
+ * separately because there is no secure bank in V8 (no _EL3). This allows
+ * the secure register to be properly reset and migrated. There is also no
+ * v8 EL1 version of the register so the non-secure instance stands alone.
+ */
+ { .name = "FCSEIDR(NS)",
+ .cp = 15, .opc1 = 0, .crn = 13, .crm = 0, .opc2 = 0,
+ .access = PL1_RW, .secure = ARM_CP_SECSTATE_NS,
+ .fieldoffset = offsetof(CPUARMState, cp15.fcseidr_ns),
+ .resetvalue = 0, .writefn = fcse_write, .raw_writefn = raw_write, },
+ { .name = "FCSEIDR(S)",
+ .cp = 15, .opc1 = 0, .crn = 13, .crm = 0, .opc2 = 0,
+ .access = PL1_RW, .secure = ARM_CP_SECSTATE_S,
+ .fieldoffset = offsetof(CPUARMState, cp15.fcseidr_s),
.resetvalue = 0, .writefn = fcse_write, .raw_writefn = raw_write, },
- { .name = "CONTEXTIDR", .state = ARM_CP_STATE_BOTH,
+ /* Define the secure and non-secure context identifier CP registers
+ * separately because there is no secure bank in V8 (no _EL3). This allows
+ * the secure register to be properly reset and migrated. In the
+ * non-secure case, the 32-bit register will have reset and migration
+ * disabled during registration as it is handled by the 64-bit instance.
+ */
+ { .name = "CONTEXTIDR_EL1", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .opc1 = 0, .crn = 13, .crm = 0, .opc2 = 1,
- .access = PL1_RW,
- .fieldoffset = offsetof(CPUARMState, cp15.contextidr_el1),
+ .access = PL1_RW, .secure = ARM_CP_SECSTATE_NS,
+ .fieldoffset = offsetof(CPUARMState, cp15.contextidr_el[1]),
+ .resetvalue = 0, .writefn = contextidr_write, .raw_writefn = raw_write, },
+ { .name = "CONTEXTIDR(S)", .state = ARM_CP_STATE_AA32,
+ .cp = 15, .opc1 = 0, .crn = 13, .crm = 0, .opc2 = 1,
+ .access = PL1_RW, .secure = ARM_CP_SECSTATE_S,
+ .fieldoffset = offsetof(CPUARMState, cp15.contextidr_s),
.resetvalue = 0, .writefn = contextidr_write, .raw_writefn = raw_write, },
REGINFO_SENTINEL
};
@@ -1031,23 +1054,31 @@ static const ARMCPRegInfo v6k_cp_reginfo[] = {
{ .name = "TPIDR_EL0", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .opc1 = 3, .opc2 = 2, .crn = 13, .crm = 0,
.access = PL0_RW,
- .fieldoffset = offsetof(CPUARMState, cp15.tpidr_el0), .resetvalue = 0 },
+ .fieldoffset = offsetof(CPUARMState, cp15.tpidr_el[0]), .resetvalue = 0 },
{ .name = "TPIDRURW", .cp = 15, .crn = 13, .crm = 0, .opc1 = 0, .opc2 = 2,
.access = PL0_RW,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.tpidr_el0),
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.tpidrurw_s),
+ offsetoflow32(CPUARMState, cp15.tpidrurw_ns) },
.resetfn = arm_cp_reset_ignore },
{ .name = "TPIDRRO_EL0", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .opc1 = 3, .opc2 = 3, .crn = 13, .crm = 0,
.access = PL0_R|PL1_W,
- .fieldoffset = offsetof(CPUARMState, cp15.tpidrro_el0), .resetvalue = 0 },
+ .fieldoffset = offsetof(CPUARMState, cp15.tpidrro_el[0]),
+ .resetvalue = 0},
{ .name = "TPIDRURO", .cp = 15, .crn = 13, .crm = 0, .opc1 = 0, .opc2 = 3,
.access = PL0_R|PL1_W,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.tpidrro_el0),
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.tpidruro_s),
+ offsetoflow32(CPUARMState, cp15.tpidruro_ns) },
.resetfn = arm_cp_reset_ignore },
- { .name = "TPIDR_EL1", .state = ARM_CP_STATE_BOTH,
+ { .name = "TPIDR_EL1", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .opc1 = 0, .opc2 = 4, .crn = 13, .crm = 0,
.access = PL1_RW,
- .fieldoffset = offsetof(CPUARMState, cp15.tpidr_el1), .resetvalue = 0 },
+ .fieldoffset = offsetof(CPUARMState, cp15.tpidr_el[1]), .resetvalue = 0 },
+ { .name = "TPIDRPRW", .opc1 = 0, .cp = 15, .crn = 13, .crm = 0, .opc2 = 4,
+ .access = PL1_RW,
+ .bank_fieldoffsets = { offsetoflow32(CPUARMState, cp15.tpidrprw_s),
+ offsetoflow32(CPUARMState, cp15.tpidrprw_ns) },
+ .resetvalue = 0 },
REGINFO_SENTINEL
};
@@ -5049,8 +5080,9 @@ static inline int get_phys_addr(CPUARMState *env, target_ulong address,
uint32_t sctlr = A32_BANKED_CURRENT_REG_GET(env, sctlr);
/* Fast Context Switch Extension. */
- if (address < 0x02000000)
- address += env->cp15.c13_fcse;
+ if (address < 0x02000000) {
+ address += A32_BANKED_CURRENT_REG_GET(env, fcseidr);
+ }
if ((sctlr & SCTLR_M) == 0) {
/* MMU/MPU disabled. */
diff --git a/target-arm/op_helper.c b/target-arm/op_helper.c
index a8dea5a..2bed914 100644
--- a/target-arm/op_helper.c
+++ b/target-arm/op_helper.c
@@ -575,7 +575,7 @@ static bool linked_bp_matches(ARMCPU *cpu, int lbn)
* short descriptor format (in which case it holds both PROCID and ASID),
* since we don't implement the optional v7 context ID masking.
*/
- contextidr = extract64(env->cp15.contextidr_el1, 0, 32);
+ contextidr = extract64(env->cp15.contextidr_el[1], 0, 32);
switch (bt) {
case 3: /* linked context ID match */
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 25/26] target-arm: make MAIR0/1 banked
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (23 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 24/26] target-arm: make c13 cp regs banked (FCSEIDR, ...) Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 26/26] target-arm: add cpu feature EL3 to CPUs with Security Extensions Greg Bellows
2014-11-25 14:41 ` [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Peter Maydell
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
Added CP register info entries for the ARMv7 MAIR0/1 secure banks.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
---
v8 -> v9
- Added endianness support to the MAIR field structure definition.
v5 -> v6
- Changed _el field variants to be array based
---
target-arm/cpu.h | 21 ++++++++++++++++++++-
target-arm/helper.c | 12 +++++++++---
2 files changed, 29 insertions(+), 4 deletions(-)
diff --git a/target-arm/cpu.h b/target-arm/cpu.h
index a1fefe4..7ba55f0 100644
--- a/target-arm/cpu.h
+++ b/target-arm/cpu.h
@@ -296,7 +296,26 @@ typedef struct CPUARMState {
uint32_t c9_pmxevtyper; /* perf monitor event type */
uint32_t c9_pmuserenr; /* perf monitor user enable */
uint32_t c9_pminten; /* perf monitor interrupt enables */
- uint64_t mair_el1;
+ union { /* Memory attribute redirection */
+ struct {
+#ifdef HOST_WORDS_BIGENDIAN
+ uint64_t _unused_mair_0;
+ uint32_t mair1_ns;
+ uint32_t mair0_ns;
+ uint64_t _unused_mair_1;
+ uint32_t mair1_s;
+ uint32_t mair0_s;
+#else
+ uint64_t _unused_mair_0;
+ uint32_t mair0_ns;
+ uint32_t mair1_ns;
+ uint64_t _unused_mair_1;
+ uint32_t mair0_s;
+ uint32_t mair1_s;
+#endif
+ };
+ uint64_t mair_el[4];
+ };
union { /* vector base address register */
struct {
uint64_t _unused_vbar;
diff --git a/target-arm/helper.c b/target-arm/helper.c
index b611573..fcbbd74 100644
--- a/target-arm/helper.c
+++ b/target-arm/helper.c
@@ -965,20 +965,26 @@ static const ARMCPRegInfo v7_cp_reginfo[] = {
*/
{ .name = "MAIR_EL1", .state = ARM_CP_STATE_AA64,
.opc0 = 3, .opc1 = 0, .crn = 10, .crm = 2, .opc2 = 0,
- .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.mair_el1),
+ .access = PL1_RW, .fieldoffset = offsetof(CPUARMState, cp15.mair_el[1]),
.resetvalue = 0 },
/* For non-long-descriptor page tables these are PRRR and NMRR;
* regardless they still act as reads-as-written for QEMU.
* The override is necessary because of the overly-broad TLB_LOCKDOWN
* definition.
*/
+ /* MAIR0/1 are defined seperately from their 64-bit counterpart which
+ * allows them to assign the correct fieldoffset based on the endianness
+ * handled in the field definitions.
+ */
{ .name = "MAIR0", .state = ARM_CP_STATE_AA32, .type = ARM_CP_OVERRIDE,
.cp = 15, .opc1 = 0, .crn = 10, .crm = 2, .opc2 = 0, .access = PL1_RW,
- .fieldoffset = offsetoflow32(CPUARMState, cp15.mair_el1),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.mair0_s),
+ offsetof(CPUARMState, cp15.mair0_ns) },
.resetfn = arm_cp_reset_ignore },
{ .name = "MAIR1", .state = ARM_CP_STATE_AA32, .type = ARM_CP_OVERRIDE,
.cp = 15, .opc1 = 0, .crn = 10, .crm = 2, .opc2 = 1, .access = PL1_RW,
- .fieldoffset = offsetofhigh32(CPUARMState, cp15.mair_el1),
+ .bank_fieldoffsets = { offsetof(CPUARMState, cp15.mair1_s),
+ offsetof(CPUARMState, cp15.mair1_ns) },
.resetfn = arm_cp_reset_ignore },
{ .name = "ISR_EL1", .state = ARM_CP_STATE_BOTH,
.opc0 = 3, .opc1 = 0, .crn = 12, .crm = 1, .opc2 = 0,
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Qemu-devel] [PATCH v11 26/26] target-arm: add cpu feature EL3 to CPUs with Security Extensions
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (24 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 25/26] target-arm: make MAIR0/1 banked Greg Bellows
@ 2014-11-17 16:47 ` Greg Bellows
2014-11-25 14:41 ` [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Peter Maydell
26 siblings, 0 replies; 30+ messages in thread
From: Greg Bellows @ 2014-11-17 16:47 UTC (permalink / raw)
To: qemu-devel, serge.fdrv, edgar.iglesias, aggelerf, peter.maydell
Cc: greg.bellows
From: Fabian Aggeler <aggelerf@ethz.ch>
Set ARM_FEATURE_EL3 feature for CPUs that implement Security Extensions.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
---
target-arm/cpu.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/target-arm/cpu.c b/target-arm/cpu.c
index d3db279..1871865 100644
--- a/target-arm/cpu.c
+++ b/target-arm/cpu.c
@@ -640,6 +640,7 @@ static void arm1176_initfn(Object *obj)
set_feature(&cpu->env, ARM_FEATURE_DUMMY_C15_REGS);
set_feature(&cpu->env, ARM_FEATURE_CACHE_DIRTY_REG);
set_feature(&cpu->env, ARM_FEATURE_CACHE_BLOCK_OPS);
+ set_feature(&cpu->env, ARM_FEATURE_EL3);
cpu->midr = 0x410fb767;
cpu->reset_fpsid = 0x410120b5;
cpu->mvfr0 = 0x11111111;
@@ -728,6 +729,7 @@ static void cortex_a8_initfn(Object *obj)
set_feature(&cpu->env, ARM_FEATURE_NEON);
set_feature(&cpu->env, ARM_FEATURE_THUMB2EE);
set_feature(&cpu->env, ARM_FEATURE_DUMMY_C15_REGS);
+ set_feature(&cpu->env, ARM_FEATURE_EL3);
cpu->midr = 0x410fc080;
cpu->reset_fpsid = 0x410330c0;
cpu->mvfr0 = 0x11110222;
@@ -795,6 +797,7 @@ static void cortex_a9_initfn(Object *obj)
set_feature(&cpu->env, ARM_FEATURE_VFP_FP16);
set_feature(&cpu->env, ARM_FEATURE_NEON);
set_feature(&cpu->env, ARM_FEATURE_THUMB2EE);
+ set_feature(&cpu->env, ARM_FEATURE_EL3);
/* Note that A9 supports the MP extensions even for
* A9UP and single-core A9MP (which are both different
* and valid configurations; we don't model A9UP).
@@ -862,6 +865,7 @@ static void cortex_a15_initfn(Object *obj)
set_feature(&cpu->env, ARM_FEATURE_DUMMY_C15_REGS);
set_feature(&cpu->env, ARM_FEATURE_CBAR_RO);
set_feature(&cpu->env, ARM_FEATURE_LPAE);
+ set_feature(&cpu->env, ARM_FEATURE_EL3);
cpu->kvm_target = QEMU_KVM_ARM_TARGET_CORTEX_A15;
cpu->midr = 0x412fc0f1;
cpu->reset_fpsid = 0x410430f0;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread* Re: [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs
2014-11-17 16:47 [Qemu-devel] [PATCH v11 00/26] target-arm: add Security Extensions for CPUs Greg Bellows
` (25 preceding siblings ...)
2014-11-17 16:47 ` [Qemu-devel] [PATCH v11 26/26] target-arm: add cpu feature EL3 to CPUs with Security Extensions Greg Bellows
@ 2014-11-25 14:41 ` Peter Maydell
26 siblings, 0 replies; 30+ messages in thread
From: Peter Maydell @ 2014-11-25 14:41 UTC (permalink / raw)
To: Greg Bellows
Cc: Sergey Fedorov, QEMU Developers, Fabian Aggeler,
Edgar E. Iglesias
On 17 November 2014 at 16:47, Greg Bellows <greg.bellows@linaro.org> wrote:
> Version 11 of the ARM processor security extension (TrustZone) support. This
> patchset includes changes to support the processor security extensions
> on ARMv7 aarch32 with hooks for later enabling v8 aarch64/32.
>
> This update includes minor fixes based on v9/v10 feedback. See the individual
> patches for details.
Since all of patches 1..25 now have my reviewed-by, I'm going to
pull them into target-arm.next ready for when 2.3 development
reopens. Patch 26 we can't apply yet until we've sorted out the
necessary properties etc so that board models can disable the
TZ support if needed.
thanks
-- PMM
^ permalink raw reply [flat|nested] 30+ messages in thread