[Qemu-devel] [PULL 42/47] serial: only resample THR interrupt on rising edge of IER.THRI

[Paolo Bonzini <pbonzini@redhat.com>]

There is disagreement on whether LSR.THRE should be resampled when
IER.THRI goes from 1 to 1.  Bochs only does it if IER.THRI goes from 0
to 1; PCE does it even if IER.THRI is unchanged.  But the Windows driver
seems to always go from 1 to 0 and back to 1, so do things in agreement
with Bochs, because the handling of thr_ipending was reported in 2010
(https://lists.gnu.org/archive/html/qemu-devel/2010-03/msg01914.html)
as breaking DR-DOS Plus.

Reported-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
---
 hw/char/serial.c | 25 ++++++++++++++++---------
 1 file changed, 16 insertions(+), 9 deletions(-)

diff --git a/hw/char/serial.c b/hw/char/serial.c
index 76054a5..6d522ff 100644
--- a/hw/char/serial.c
+++ b/hw/char/serial.c
@@ -336,10 +336,12 @@ static void serial_ioport_write(void *opaque, hwaddr addr, uint64_t val,
             s->divider = (s->divider & 0x00ff) | (val << 8);
             serial_update_parameters(s);
         } else {
+            uint8_t changed = (s->ier ^ val) & 0x0f;
             s->ier = val & 0x0f;
             /* If the backend device is a real serial port, turn polling of the modem
-               status lines on physical port on or off depending on UART_IER_MSI state */
-            if (s->poll_msl >= 0) {
+             * status lines on physical port on or off depending on UART_IER_MSI state.
+             */
+            if ((changed & UART_IER_MSI) && s->poll_msl >= 0) {
                 if (s->ier & UART_IER_MSI) {
                      s->poll_msl = 1;
                      serial_update_msl(s);
@@ -354,18 +356,23 @@ static void serial_ioport_write(void *opaque, hwaddr addr, uint64_t val,
              * This is not in the datasheet, but Windows relies on it.  It is
              * unclear if THRE has to be resampled every time THRI becomes
              * 1, or only on the rising edge.  Bochs does the latter, and Windows
-             * always toggles IER to all zeroes and back to all ones.  But for
-             * now leave it as it has always been in QEMU.
+             * always toggles IER to all zeroes and back to all ones, so do the
+             * same.
              *
              * If IER.THRI is zero, thr_ipending is not used.  Set it to zero
              * so that the thr_ipending subsection is not migrated.
              */
-            if ((s->ier & UART_IER_THRI) && (s->lsr & UART_LSR_THRE)) {
-                s->thr_ipending = 1;
-            } else {
-                s->thr_ipending = 0;
+            if (changed & UART_IER_THRI) {
+                if ((s->ier & UART_IER_THRI) && (s->lsr & UART_LSR_THRE)) {
+                    s->thr_ipending = 1;
+                } else {
+                    s->thr_ipending = 0;
+                }
+            }
+
+            if (changed) {
+                serial_update_irq(s);
             }
-            serial_update_irq(s);
         }
         break;
     case 2:
-- 
1.8.3.1