* [Qemu-devel] [PATCH v2 01/10] m25p80: Replace JEDEC ID masking with function.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 12:19 ` Cédric Le Goater
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 02/10] m25p80: Make a table for JEDEC ID marcin.krzeminski
` (8 subsequent siblings)
9 siblings, 1 reply; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Instead of always reading and comparing jededc ID,
replace it by function.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
---
hw/block/m25p80.c | 49 ++++++++++++++++++++++++++++++++++++++++---------
1 file changed, 40 insertions(+), 9 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 4c856f5..15765f5 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -307,6 +307,14 @@ typedef enum {
STATE_READING_DATA,
} CMDState;
+typedef enum {
+ MAN_SPANSION,
+ MAN_MACRONIX,
+ MAN_NUMONYX,
+ MAN_WINBOND,
+ MAN_GENERIC,
+} Manufacturer;
+
typedef struct Flash {
SSISlave parent_obj;
@@ -350,6 +358,22 @@ typedef struct M25P80Class {
#define M25P80_GET_CLASS(obj) \
OBJECT_GET_CLASS(M25P80Class, (obj), TYPE_M25P80)
+static inline Manufacturer get_man(Flash *s)
+{
+ switch (((s->pi->jedec >> 16) & 0xFF)) {
+ case 0x20:
+ return MAN_NUMONYX;
+ case 0xEF:
+ return MAN_WINBOND;
+ case 0x01:
+ return MAN_SPANSION;
+ case 0xC2:
+ return MAN_MACRONIX;
+ default:
+ return MAN_GENERIC;
+ }
+}
+
static void blk_sync_complete(void *opaque, int ret)
{
/* do nothing. Masters do not directly interact with the backing store,
@@ -562,7 +586,8 @@ static void reset_memory(Flash *s)
s->write_enable = false;
s->reset_enable = false;
- if (((s->pi->jedec >> 16) & 0xFF) == JEDEC_NUMONYX) {
+ switch (get_man(s)) {
+ case MAN_NUMONYX:
s->volatile_cfg = 0;
s->volatile_cfg |= VCFG_DUMMY;
s->volatile_cfg |= VCFG_WRAP_SEQUENTIAL;
@@ -594,6 +619,9 @@ static void reset_memory(Flash *s)
if (!(s->nonvolatile_cfg & NVCFG_LOWER_SEGMENT_MASK)) {
s->ear = CFG_UPPER_128MB_SEG_ENABLED;
}
+ break;
+ default:
+ break;
}
DB_PRINT_L(0, "Reset done.\n");
@@ -634,9 +662,12 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case QOR:
case QOR4:
s->needed_bytes = get_addr_length(s);
- if (((s->pi->jedec >> 16) & 0xFF) == JEDEC_NUMONYX) {
- /* Dummy cycles modeled with bytes writes instead of bits */
+ switch (get_man(s)) {
+ case MAN_NUMONYX:
s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
+ break;
+ default:
+ break;
}
s->pos = 0;
s->len = 0;
@@ -645,9 +676,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case DIOR:
case DIOR4:
- switch ((s->pi->jedec >> 16) & 0xFF) {
- case JEDEC_WINBOND:
- case JEDEC_SPANSION:
+ switch (get_man(s)) {
+ case MAN_WINBOND:
+ case MAN_SPANSION:
s->needed_bytes = 4;
break;
default:
@@ -662,9 +693,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case QIOR:
case QIOR4:
- switch ((s->pi->jedec >> 16) & 0xFF) {
- case JEDEC_WINBOND:
- case JEDEC_SPANSION:
+ switch (get_man(s)) {
+ case MAN_WINBOND:
+ case MAN_SPANSION:
s->needed_bytes = 6;
break;
default:
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* Re: [Qemu-devel] [PATCH v2 01/10] m25p80: Replace JEDEC ID masking with function.
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 01/10] m25p80: Replace JEDEC ID masking with function marcin.krzeminski
@ 2016-06-17 12:19 ` Cédric Le Goater
0 siblings, 0 replies; 15+ messages in thread
From: Cédric Le Goater @ 2016-06-17 12:19 UTC (permalink / raw)
To: marcin.krzeminski, qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, peter.maydell, clg
On 06/17/2016 12:28 PM, marcin.krzeminski@nokia.com wrote:
> From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
>
> Instead of always reading and comparing jededc ID,
> replace it by function.
>
> Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Thanks,
C.
> ---
> hw/block/m25p80.c | 49 ++++++++++++++++++++++++++++++++++++++++---------
> 1 file changed, 40 insertions(+), 9 deletions(-)
>
> diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> index 4c856f5..15765f5 100644
> --- a/hw/block/m25p80.c
> +++ b/hw/block/m25p80.c
> @@ -307,6 +307,14 @@ typedef enum {
> STATE_READING_DATA,
> } CMDState;
>
> +typedef enum {
> + MAN_SPANSION,
> + MAN_MACRONIX,
> + MAN_NUMONYX,
> + MAN_WINBOND,
> + MAN_GENERIC,
> +} Manufacturer;
> +
> typedef struct Flash {
> SSISlave parent_obj;
>
> @@ -350,6 +358,22 @@ typedef struct M25P80Class {
> #define M25P80_GET_CLASS(obj) \
> OBJECT_GET_CLASS(M25P80Class, (obj), TYPE_M25P80)
>
> +static inline Manufacturer get_man(Flash *s)
> +{
> + switch (((s->pi->jedec >> 16) & 0xFF)) {
> + case 0x20:
> + return MAN_NUMONYX;
> + case 0xEF:
> + return MAN_WINBOND;
> + case 0x01:
> + return MAN_SPANSION;
> + case 0xC2:
> + return MAN_MACRONIX;
> + default:
> + return MAN_GENERIC;
> + }
> +}
> +
> static void blk_sync_complete(void *opaque, int ret)
> {
> /* do nothing. Masters do not directly interact with the backing store,
> @@ -562,7 +586,8 @@ static void reset_memory(Flash *s)
> s->write_enable = false;
> s->reset_enable = false;
>
> - if (((s->pi->jedec >> 16) & 0xFF) == JEDEC_NUMONYX) {
> + switch (get_man(s)) {
> + case MAN_NUMONYX:
> s->volatile_cfg = 0;
> s->volatile_cfg |= VCFG_DUMMY;
> s->volatile_cfg |= VCFG_WRAP_SEQUENTIAL;
> @@ -594,6 +619,9 @@ static void reset_memory(Flash *s)
> if (!(s->nonvolatile_cfg & NVCFG_LOWER_SEGMENT_MASK)) {
> s->ear = CFG_UPPER_128MB_SEG_ENABLED;
> }
> + break;
> + default:
> + break;
> }
>
> DB_PRINT_L(0, "Reset done.\n");
> @@ -634,9 +662,12 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> case QOR:
> case QOR4:
> s->needed_bytes = get_addr_length(s);
> - if (((s->pi->jedec >> 16) & 0xFF) == JEDEC_NUMONYX) {
> - /* Dummy cycles modeled with bytes writes instead of bits */
> + switch (get_man(s)) {
> + case MAN_NUMONYX:
> s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> + break;
> + default:
> + break;
> }
> s->pos = 0;
> s->len = 0;
> @@ -645,9 +676,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>
> case DIOR:
> case DIOR4:
> - switch ((s->pi->jedec >> 16) & 0xFF) {
> - case JEDEC_WINBOND:
> - case JEDEC_SPANSION:
> + switch (get_man(s)) {
> + case MAN_WINBOND:
> + case MAN_SPANSION:
> s->needed_bytes = 4;
> break;
> default:
> @@ -662,9 +693,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>
> case QIOR:
> case QIOR4:
> - switch ((s->pi->jedec >> 16) & 0xFF) {
> - case JEDEC_WINBOND:
> - case JEDEC_SPANSION:
> + switch (get_man(s)) {
> + case MAN_WINBOND:
> + case MAN_SPANSION:
> s->needed_bytes = 6;
> break;
> default:
>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [Qemu-devel] [PATCH v2 02/10] m25p80: Make a table for JEDEC ID.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 01/10] m25p80: Replace JEDEC ID masking with function marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 03/10] m25p80: Allow more than four banks marcin.krzeminski
` (7 subsequent siblings)
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Since it is now longer than 4. This work based on Pawel Lenkow
changes and the kernel SPI framework.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 61 ++++++++++++++++++++++++++++++++++++++-----------------
1 file changed, 42 insertions(+), 19 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 15765f5..342f7c9 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -53,12 +53,17 @@
/* 16 MiB max in 3 byte address mode */
#define MAX_3BYTES_SIZE 0x1000000
+#define SPI_NOR_MAX_ID_LEN 6
+
typedef struct FlashPartInfo {
const char *part_name;
- /* jedec code. (jedec >> 16) & 0xff is the 1st byte, >> 8 the 2nd etc */
- uint32_t jedec;
- /* extended jedec code */
- uint16_t ext_jedec;
+ /*
+ * This array stores the ID bytes.
+ * The first three bytes are the JEDIC ID.
+ * JEDEC ID zero means "no ID" (mostly older chips).
+ */
+ uint8_t id[SPI_NOR_MAX_ID_LEN];
+ uint8_t id_len;
/* there is confusion between manufacturers as to what a sector is. In this
* device model, a "sector" is the size that is erased by the ERASE_SECTOR
* command (opcode 0xd8).
@@ -70,11 +75,33 @@ typedef struct FlashPartInfo {
} FlashPartInfo;
/* adapted from linux */
-
-#define INFO(_part_name, _jedec, _ext_jedec, _sector_size, _n_sectors, _flags)\
- .part_name = (_part_name),\
- .jedec = (_jedec),\
- .ext_jedec = (_ext_jedec),\
+/* Used when the "_ext_id" is two bytes at most */
+#define INFO(_part_name, _jedec_id, _ext_id, _sector_size, _n_sectors, _flags)\
+ .part_name = _part_name,\
+ .id = {\
+ ((_jedec_id) >> 16) & 0xff,\
+ ((_jedec_id) >> 8) & 0xff,\
+ (_jedec_id) & 0xff,\
+ ((_ext_id) >> 8) & 0xff,\
+ (_ext_id) & 0xff,\
+ },\
+ .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))),\
+ .sector_size = (_sector_size),\
+ .n_sectors = (_n_sectors),\
+ .page_size = 256,\
+ .flags = (_flags),
+
+#define INFO6(_part_name, _jedec_id, _ext_id, _sector_size, _n_sectors, _flags)\
+ .part_name = _part_name,\
+ .id = {\
+ ((_jedec_id) >> 16) & 0xff,\
+ ((_jedec_id) >> 8) & 0xff,\
+ (_jedec_id) & 0xff,\
+ ((_ext_id) >> 16) & 0xff,\
+ ((_ext_id) >> 8) & 0xff,\
+ (_ext_id) & 0xff,\
+ },\
+ .id_len = 6,\
.sector_size = (_sector_size),\
.n_sectors = (_n_sectors),\
.page_size = 256,\
@@ -360,7 +387,7 @@ typedef struct M25P80Class {
static inline Manufacturer get_man(Flash *s)
{
- switch (((s->pi->jedec >> 16) & 0xFF)) {
+ switch (s->pi->id[0]) {
case 0x20:
return MAN_NUMONYX;
case 0xEF:
@@ -630,6 +657,7 @@ static void reset_memory(Flash *s)
static void decode_new_cmd(Flash *s, uint32_t value)
{
s->cmd_in_progress = value;
+ int i;
DB_PRINT_L(0, "decoded new command:%x\n", value);
if (value != RESET_MEMORY) {
@@ -743,16 +771,11 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case JEDEC_READ:
DB_PRINT_L(0, "populated jedec code\n");
- s->data[0] = (s->pi->jedec >> 16) & 0xff;
- s->data[1] = (s->pi->jedec >> 8) & 0xff;
- s->data[2] = s->pi->jedec & 0xff;
- if (s->pi->ext_jedec) {
- s->data[3] = (s->pi->ext_jedec >> 8) & 0xff;
- s->data[4] = s->pi->ext_jedec & 0xff;
- s->len = 5;
- } else {
- s->len = 3;
+ for (i = 0; i < s->pi->id_len; i++) {
+ s->data[i] = s->pi->id[i];
}
+
+ s->len = s->pi->id_len;
s->pos = 0;
s->state = STATE_READING_DATA;
break;
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 03/10] m25p80: Allow more than four banks.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 01/10] m25p80: Replace JEDEC ID masking with function marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 02/10] m25p80: Make a table for JEDEC ID marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 04/10] m25p80: Introduce COLLECTING_VAR_LEN_DATA state marcin.krzeminski
` (6 subsequent siblings)
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Allow to have more than four 16MiB regions for bigger flash devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 342f7c9..6910c52 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -129,7 +129,6 @@ typedef struct FlashPartInfo {
#define EVCFG_QUAD_IO_ENABLED (1 << 7)
#define NVCFG_4BYTE_ADDR_MASK (1 << 0)
#define NVCFG_LOWER_SEGMENT_MASK (1 << 1)
-#define CFG_UPPER_128MB_SEG_ENABLED 0x3
/* Numonyx (Micron) Flag Status Register macros */
#define FSR_4BYTE_ADDR_MODE_ENABLED 0x1
@@ -545,7 +544,7 @@ static void complete_collecting_data(Flash *s)
}
if (get_addr_length(s) == 3) {
- s->cur_addr += (s->ear & 0x3) * MAX_3BYTES_SIZE;
+ s->cur_addr += s->ear * MAX_3BYTES_SIZE;
}
s->state = STATE_IDLE;
@@ -644,7 +643,7 @@ static void reset_memory(Flash *s)
s->four_bytes_address_mode = true;
}
if (!(s->nonvolatile_cfg & NVCFG_LOWER_SEGMENT_MASK)) {
- s->ear = CFG_UPPER_128MB_SEG_ENABLED;
+ s->ear = s->size / MAX_3BYTES_SIZE - 1;
}
break;
default:
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 04/10] m25p80: Introduce COLLECTING_VAR_LEN_DATA state.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (2 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 03/10] m25p80: Allow more than four banks marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 05/10] m25p80: Add additional flash commands: marcin.krzeminski
` (5 subsequent siblings)
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Some flash allows to stop read at any time.
Allow framework to support this.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 6910c52..ca1f882 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -330,6 +330,7 @@ typedef enum {
STATE_PAGE_PROGRAM,
STATE_READ,
STATE_COLLECTING_DATA,
+ STATE_COLLECTING_VAR_LEN_DATA,
STATE_READING_DATA,
} CMDState;
@@ -872,6 +873,9 @@ static int m25p80_cs(SSISlave *ss, bool select)
Flash *s = M25P80(ss);
if (select) {
+ if (s->state == STATE_COLLECTING_VAR_LEN_DATA) {
+ complete_collecting_data(s);
+ }
s->len = 0;
s->pos = 0;
s->state = STATE_IDLE;
@@ -905,6 +909,7 @@ static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx)
break;
case STATE_COLLECTING_DATA:
+ case STATE_COLLECTING_VAR_LEN_DATA:
s->data[s->len] = (uint8_t)tx;
s->len++;
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 05/10] m25p80: Add additional flash commands:
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (3 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 04/10] m25p80: Introduce COLLECTING_VAR_LEN_DATA state marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 06/10] m25p80: Introduce quad and equad modes marcin.krzeminski
` (4 subsequent siblings)
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Page program 4byte/quad and erase 32K sectors 4 bytes.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index ca1f882..55b4377 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -297,12 +297,14 @@ typedef enum {
PP = 0x02,
PP4 = 0x12,
+ PP4_4 = 0x3e,
DPP = 0xa2,
QPP = 0x32,
ERASE_4K = 0x20,
ERASE4_4K = 0x21,
ERASE_32K = 0x52,
+ ERASE4_32K = 0x5c,
ERASE_SECTOR = 0xd8,
ERASE4_SECTOR = 0xdc,
@@ -449,6 +451,7 @@ static void flash_erase(Flash *s, int offset, FlashCMD cmd)
capa_to_assert = ER_4K;
break;
case ERASE_32K:
+ case ERASE4_32K:
len = 32 << 10;
capa_to_assert = ER_32K;
break;
@@ -519,9 +522,11 @@ static inline int get_addr_length(Flash *s)
switch (s->cmd_in_progress) {
case PP4:
+ case PP4_4:
case READ4:
case QIOR4:
case ERASE4_4K:
+ case ERASE4_32K:
case ERASE4_SECTOR:
case FAST_READ4:
case DOR4:
@@ -555,6 +560,7 @@ static void complete_collecting_data(Flash *s)
case QPP:
case PP:
case PP4:
+ case PP4_4:
s->state = STATE_PAGE_PROGRAM;
break;
case READ:
@@ -574,6 +580,7 @@ static void complete_collecting_data(Flash *s)
case ERASE_4K:
case ERASE4_4K:
case ERASE_32K:
+ case ERASE4_32K:
case ERASE_SECTOR:
case ERASE4_SECTOR:
flash_erase(s, s->cur_addr, s->cmd_in_progress);
@@ -669,6 +676,7 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case ERASE_4K:
case ERASE4_4K:
case ERASE_32K:
+ case ERASE4_32K:
case ERASE_SECTOR:
case ERASE4_SECTOR:
case READ:
@@ -677,6 +685,7 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case QPP:
case PP:
case PP4:
+ case PP4_4:
s->needed_bytes = get_addr_length(s);
s->pos = 0;
s->len = 0;
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 06/10] m25p80: Introduce quad and equad modes.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (4 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 05/10] m25p80: Add additional flash commands: marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 12:33 ` Cédric Le Goater
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 07/10] m25p80: Introduce configuration registers marcin.krzeminski
` (3 subsequent siblings)
9 siblings, 1 reply; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Quad and Equad modes for Spansion and Macronix flash devices.
This commit also includes modification and new command to manipulate
quad mode (status registers and dedicated commands).
This work is based on Pawel Lenkow work.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
---
hw/block/m25p80.c | 70 +++++++++++++++++++++++++++++++++++++++++++++++++++----
1 file changed, 65 insertions(+), 5 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 55b4377..d1c4d46 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -281,6 +281,7 @@ typedef enum {
JEDEC_READ = 0x9f,
BULK_ERASE = 0xc7,
READ_FSR = 0x70,
+ RDCR = 0x15,
READ = 0x03,
READ4 = 0x13,
@@ -317,6 +318,13 @@ typedef enum {
RESET_ENABLE = 0x66,
RESET_MEMORY = 0x99,
+ /*
+ * Micron: 0x35 - enable QPI
+ * Spansion: 0x35 - read control register
+ */
+ RDCR_EQIO = 0x35,
+ RSTQIO = 0xf5,
+
RNVCR = 0xB5,
WNVCR = 0xB1,
@@ -366,6 +374,7 @@ typedef struct Flash {
bool write_enable;
bool four_bytes_address_mode;
bool reset_enable;
+ bool quad_enable;
uint8_t ear;
int64_t dirty_page;
@@ -586,6 +595,16 @@ static void complete_collecting_data(Flash *s)
flash_erase(s, s->cur_addr, s->cmd_in_progress);
break;
case WRSR:
+ switch (get_man(s)) {
+ case MAN_SPANSION:
+ s->quad_enable = !!(s->data[1] & 0x02);
+ break;
+ case MAN_MACRONIX:
+ s->quad_enable = extract32(s->data[0], 6, 1);
+ break;
+ default:
+ break;
+ }
if (s->write_enable) {
s->write_enable = false;
}
@@ -619,6 +638,7 @@ static void reset_memory(Flash *s)
s->state = STATE_IDLE;
s->write_enable = false;
s->reset_enable = false;
+ s->quad_enable = false;
switch (get_man(s)) {
case MAN_NUMONYX:
@@ -747,10 +767,20 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case WRSR:
if (s->write_enable) {
- s->needed_bytes = 1;
+ switch (get_man(s)) {
+ case MAN_SPANSION:
+ s->needed_bytes = 2;
+ s->state = STATE_COLLECTING_DATA;
+ break;
+ case MAN_MACRONIX:
+ s->needed_bytes = 2;
+ s->state = STATE_COLLECTING_VAR_LEN_DATA;
+ break;
+ default:
+ s->needed_bytes = 1;
+ s->state = STATE_COLLECTING_DATA;
+ }
s->pos = 0;
- s->len = 0;
- s->state = STATE_COLLECTING_DATA;
}
break;
@@ -763,6 +793,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case RDSR:
s->data[0] = (!!s->write_enable) << 1;
+ if (get_man(s) == MAN_MACRONIX) {
+ s->data[0] |= (!!s->quad_enable) << 6;
+ }
s->pos = 0;
s->len = 1;
s->state = STATE_READING_DATA;
@@ -789,6 +822,14 @@ static void decode_new_cmd(Flash *s, uint32_t value)
s->state = STATE_READING_DATA;
break;
+ case RDCR:
+ s->data[0] = s->volatile_cfg & 0xFF;
+ s->data[0] |= (!!s->four_bytes_address_mode) << 5;
+ s->pos = 0;
+ s->len = 1;
+ s->state = STATE_READING_DATA;
+ break;
+
case BULK_ERASE:
if (s->write_enable) {
DB_PRINT_L(0, "chip erase\n");
@@ -828,7 +869,7 @@ static void decode_new_cmd(Flash *s, uint32_t value)
s->state = STATE_READING_DATA;
break;
case WNVCR:
- if (s->write_enable) {
+ if (s->write_enable && get_man(s) == MAN_NUMONYX) {
s->needed_bytes = 2;
s->pos = 0;
s->len = 0;
@@ -871,6 +912,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)
reset_memory(s);
}
break;
+ case RDCR_EQIO:
+ switch (get_man(s)) {
+ case MAN_SPANSION:
+ s->data[0] = (!!s->quad_enable) << 1;
+ s->pos = 0;
+ s->len = 1;
+ s->state = STATE_READING_DATA;
+ break;
+ case MAN_MACRONIX:
+ s->quad_enable = true;
+ break;
+ default:
+ break;
+ }
+ break;
+ case RSTQIO:
+ s->quad_enable = false;
+ break;
default:
qemu_log_mask(LOG_GUEST_ERROR, "M25P80: Unknown cmd %x\n", value);
break;
@@ -999,7 +1058,7 @@ static Property m25p80_properties[] = {
static const VMStateDescription vmstate_m25p80 = {
.name = "xilinx_spi",
- .version_id = 2,
+ .version_id = 3,
.minimum_version_id = 1,
.pre_save = m25p80_pre_save,
.fields = (VMStateField[]) {
@@ -1017,6 +1076,7 @@ static const VMStateDescription vmstate_m25p80 = {
VMSTATE_UINT32_V(nonvolatile_cfg, Flash, 2),
VMSTATE_UINT32_V(volatile_cfg, Flash, 2),
VMSTATE_UINT32_V(enh_volatile_cfg, Flash, 2),
+ VMSTATE_BOOL_V(quad_enable, Flash, 3),
VMSTATE_END_OF_LIST()
}
};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* Re: [Qemu-devel] [PATCH v2 06/10] m25p80: Introduce quad and equad modes.
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 06/10] m25p80: Introduce quad and equad modes marcin.krzeminski
@ 2016-06-17 12:33 ` Cédric Le Goater
0 siblings, 0 replies; 15+ messages in thread
From: Cédric Le Goater @ 2016-06-17 12:33 UTC (permalink / raw)
To: marcin.krzeminski, qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, peter.maydell, clg
On 06/17/2016 12:28 PM, marcin.krzeminski@nokia.com wrote:
> From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
>
> Quad and Equad modes for Spansion and Macronix flash devices.
> This commit also includes modification and new command to manipulate
> quad mode (status registers and dedicated commands).
> This work is based on Pawel Lenkow work.
>
> Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Thanks,
C.
> ---
> hw/block/m25p80.c | 70 +++++++++++++++++++++++++++++++++++++++++++++++++++----
> 1 file changed, 65 insertions(+), 5 deletions(-)
>
> diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> index 55b4377..d1c4d46 100644
> --- a/hw/block/m25p80.c
> +++ b/hw/block/m25p80.c
> @@ -281,6 +281,7 @@ typedef enum {
> JEDEC_READ = 0x9f,
> BULK_ERASE = 0xc7,
> READ_FSR = 0x70,
> + RDCR = 0x15,
>
> READ = 0x03,
> READ4 = 0x13,
> @@ -317,6 +318,13 @@ typedef enum {
> RESET_ENABLE = 0x66,
> RESET_MEMORY = 0x99,
>
> + /*
> + * Micron: 0x35 - enable QPI
> + * Spansion: 0x35 - read control register
> + */
> + RDCR_EQIO = 0x35,
> + RSTQIO = 0xf5,
> +
> RNVCR = 0xB5,
> WNVCR = 0xB1,
>
> @@ -366,6 +374,7 @@ typedef struct Flash {
> bool write_enable;
> bool four_bytes_address_mode;
> bool reset_enable;
> + bool quad_enable;
> uint8_t ear;
>
> int64_t dirty_page;
> @@ -586,6 +595,16 @@ static void complete_collecting_data(Flash *s)
> flash_erase(s, s->cur_addr, s->cmd_in_progress);
> break;
> case WRSR:
> + switch (get_man(s)) {
> + case MAN_SPANSION:
> + s->quad_enable = !!(s->data[1] & 0x02);
> + break;
> + case MAN_MACRONIX:
> + s->quad_enable = extract32(s->data[0], 6, 1);
> + break;
> + default:
> + break;
> + }
> if (s->write_enable) {
> s->write_enable = false;
> }
> @@ -619,6 +638,7 @@ static void reset_memory(Flash *s)
> s->state = STATE_IDLE;
> s->write_enable = false;
> s->reset_enable = false;
> + s->quad_enable = false;
>
> switch (get_man(s)) {
> case MAN_NUMONYX:
> @@ -747,10 +767,20 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>
> case WRSR:
> if (s->write_enable) {
> - s->needed_bytes = 1;
> + switch (get_man(s)) {
> + case MAN_SPANSION:
> + s->needed_bytes = 2;
> + s->state = STATE_COLLECTING_DATA;
> + break;
> + case MAN_MACRONIX:
> + s->needed_bytes = 2;
> + s->state = STATE_COLLECTING_VAR_LEN_DATA;
> + break;
> + default:
> + s->needed_bytes = 1;
> + s->state = STATE_COLLECTING_DATA;
> + }
> s->pos = 0;
> - s->len = 0;
> - s->state = STATE_COLLECTING_DATA;
> }
> break;
>
> @@ -763,6 +793,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>
> case RDSR:
> s->data[0] = (!!s->write_enable) << 1;
> + if (get_man(s) == MAN_MACRONIX) {
> + s->data[0] |= (!!s->quad_enable) << 6;
> + }
> s->pos = 0;
> s->len = 1;
> s->state = STATE_READING_DATA;
> @@ -789,6 +822,14 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> s->state = STATE_READING_DATA;
> break;
>
> + case RDCR:
> + s->data[0] = s->volatile_cfg & 0xFF;
> + s->data[0] |= (!!s->four_bytes_address_mode) << 5;
> + s->pos = 0;
> + s->len = 1;
> + s->state = STATE_READING_DATA;
> + break;
> +
> case BULK_ERASE:
> if (s->write_enable) {
> DB_PRINT_L(0, "chip erase\n");
> @@ -828,7 +869,7 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> s->state = STATE_READING_DATA;
> break;
> case WNVCR:
> - if (s->write_enable) {
> + if (s->write_enable && get_man(s) == MAN_NUMONYX) {
> s->needed_bytes = 2;
> s->pos = 0;
> s->len = 0;
> @@ -871,6 +912,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> reset_memory(s);
> }
> break;
> + case RDCR_EQIO:
> + switch (get_man(s)) {
> + case MAN_SPANSION:
> + s->data[0] = (!!s->quad_enable) << 1;
> + s->pos = 0;
> + s->len = 1;
> + s->state = STATE_READING_DATA;
> + break;
> + case MAN_MACRONIX:
> + s->quad_enable = true;
> + break;
> + default:
> + break;
> + }
> + break;
> + case RSTQIO:
> + s->quad_enable = false;
> + break;
> default:
> qemu_log_mask(LOG_GUEST_ERROR, "M25P80: Unknown cmd %x\n", value);
> break;
> @@ -999,7 +1058,7 @@ static Property m25p80_properties[] = {
>
> static const VMStateDescription vmstate_m25p80 = {
> .name = "xilinx_spi",
> - .version_id = 2,
> + .version_id = 3,
> .minimum_version_id = 1,
> .pre_save = m25p80_pre_save,
> .fields = (VMStateField[]) {
> @@ -1017,6 +1076,7 @@ static const VMStateDescription vmstate_m25p80 = {
> VMSTATE_UINT32_V(nonvolatile_cfg, Flash, 2),
> VMSTATE_UINT32_V(volatile_cfg, Flash, 2),
> VMSTATE_UINT32_V(enh_volatile_cfg, Flash, 2),
> + VMSTATE_BOOL_V(quad_enable, Flash, 3),
> VMSTATE_END_OF_LIST()
> }
> };
>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [Qemu-devel] [PATCH v2 07/10] m25p80: Introduce configuration registers.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (5 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 06/10] m25p80: Introduce quad and equad modes marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes marcin.krzeminski
` (2 subsequent siblings)
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Configuration registers for Spansion and Macronix devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 47 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index d1c4d46..21998db 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -134,6 +134,14 @@ typedef struct FlashPartInfo {
#define FSR_4BYTE_ADDR_MODE_ENABLED 0x1
#define FSR_FLASH_READY (1 << 7)
+/* Spansion configuration registers macros. */
+#define SPANSION_QUAD_CFG_POS 0
+#define SPANSION_QUAD_CFG_LEN 1
+#define SPANSION_DUMMY_CLK_POS 0
+#define SPANSION_DUMMY_CLK_LEN 4
+#define SPANSION_ADDR_LEN_POS 7
+#define SPANSION_ADDR_LEN_LEN 1
+
static const FlashPartInfo known_devices[] = {
/* Atmel -- some are (confusingly) marketed as "DataFlash" */
{ INFO("at25fs010", 0x1f6601, 0, 32 << 10, 4, ER_4K) },
@@ -369,8 +377,18 @@ typedef struct Flash {
uint8_t cmd_in_progress;
uint64_t cur_addr;
uint32_t nonvolatile_cfg;
+ /* Configuration register for Macronix */
uint32_t volatile_cfg;
uint32_t enh_volatile_cfg;
+ /* Spansion cfg registers. */
+ uint8_t spansion_cr1nv;
+ uint8_t spansion_cr2nv;
+ uint8_t spansion_cr3nv;
+ uint8_t spansion_cr4nv;
+ uint8_t spansion_cr1v;
+ uint8_t spansion_cr2v;
+ uint8_t spansion_cr3v;
+ uint8_t spansion_cr4v;
bool write_enable;
bool four_bytes_address_mode;
bool reset_enable;
@@ -601,6 +619,9 @@ static void complete_collecting_data(Flash *s)
break;
case MAN_MACRONIX:
s->quad_enable = extract32(s->data[0], 6, 1);
+ if (s->len > 1) {
+ s->four_bytes_address_mode = extract32(s->data[1], 5, 1);
+ }
break;
default:
break;
@@ -674,6 +695,23 @@ static void reset_memory(Flash *s)
s->ear = s->size / MAX_3BYTES_SIZE - 1;
}
break;
+ case MAN_MACRONIX:
+ s->volatile_cfg = 0x7;
+ break;
+ case MAN_SPANSION:
+ s->spansion_cr1v = s->spansion_cr1nv;
+ s->spansion_cr2v = s->spansion_cr2nv;
+ s->spansion_cr3v = s->spansion_cr3nv;
+ s->spansion_cr4v = s->spansion_cr4nv;
+ s->quad_enable = extract32(s->spansion_cr1v,
+ SPANSION_QUAD_CFG_POS,
+ SPANSION_QUAD_CFG_LEN
+ );
+ s->four_bytes_address_mode = extract32(s->spansion_cr2v,
+ SPANSION_ADDR_LEN_POS,
+ SPANSION_ADDR_LEN_LEN
+ );
+ break;
default:
break;
}
@@ -1052,7 +1090,12 @@ static void m25p80_pre_save(void *opaque)
}
static Property m25p80_properties[] = {
+ /* This is default value for Micron flash */
DEFINE_PROP_UINT32("nonvolatile-cfg", Flash, nonvolatile_cfg, 0x8FFF),
+ DEFINE_PROP_UINT8("spansion-cr1nv", Flash, spansion_cr1nv, 0x0),
+ DEFINE_PROP_UINT8("spansion-cr2nv", Flash, spansion_cr2nv, 0x8),
+ DEFINE_PROP_UINT8("spansion-cr3nv", Flash, spansion_cr3nv, 0x2),
+ DEFINE_PROP_UINT8("spansion-cr4nv", Flash, spansion_cr4nv, 0x10),
DEFINE_PROP_END_OF_LIST(),
};
@@ -1077,6 +1120,10 @@ static const VMStateDescription vmstate_m25p80 = {
VMSTATE_UINT32_V(volatile_cfg, Flash, 2),
VMSTATE_UINT32_V(enh_volatile_cfg, Flash, 2),
VMSTATE_BOOL_V(quad_enable, Flash, 3),
+ VMSTATE_UINT8_V(spansion_cr1nv, Flash, 3),
+ VMSTATE_UINT8_V(spansion_cr2nv, Flash, 3),
+ VMSTATE_UINT8_V(spansion_cr3nv, Flash, 3),
+ VMSTATE_UINT8_V(spansion_cr4nv, Flash, 3),
VMSTATE_END_OF_LIST()
}
};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (6 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 07/10] m25p80: Introduce configuration registers marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 12:30 ` Cédric Le Goater
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 09/10] m25p80: New flash devices marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 10/10] m25p80.c: Fix WINBOND fast read command handling marcin.krzeminski
9 siblings, 1 reply; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Support for Spansion and Macronix flashes.
Additionally Numonyx(Micron) moved from default
in fast read commands family. Also moved fast read
command decoding to functions.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
---
hw/block/m25p80.c | 145 ++++++++++++++++++++++++++++++++++++++++--------------
1 file changed, 108 insertions(+), 37 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 21998db..f40fa99 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -719,6 +719,111 @@ static void reset_memory(Flash *s)
DB_PRINT_L(0, "Reset done.\n");
}
+static void decode_fast_read_cmd(Flash *s)
+{
+ s->needed_bytes = get_addr_length(s);
+ switch (get_man(s)) {
+ /* Dummy cycles - modeled with bytes writes instead of bits */
+ case MAN_NUMONYX:
+ s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
+ break;
+ case MAN_MACRONIX:
+ if (extract32(s->volatile_cfg, 6, 2) == 1) {
+ s->needed_bytes += 6;
+ } else {
+ s->needed_bytes += 8;
+ }
+ break;
+ case MAN_SPANSION:
+ s->needed_bytes += extract32(s->spansion_cr2v,
+ SPANSION_DUMMY_CLK_POS,
+ SPANSION_DUMMY_CLK_LEN
+ );
+ break;
+ default:
+ break;
+ }
+ s->pos = 0;
+ s->len = 0;
+ s->state = STATE_COLLECTING_DATA;
+}
+
+static void decode_dio_read_cmd(Flash *s)
+{
+ s->needed_bytes = get_addr_length(s);
+ /* Dummy cycles modeled with bytes writes instead of bits */
+ switch (get_man(s)) {
+ case MAN_WINBOND:
+ s->needed_bytes = 4;
+ break;
+ case MAN_SPANSION:
+ s->needed_bytes += extract32(s->spansion_cr2v,
+ SPANSION_DUMMY_CLK_POS,
+ SPANSION_DUMMY_CLK_LEN
+ );
+ break;
+ case MAN_NUMONYX:
+ s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
+ break;
+ case MAN_MACRONIX:
+ switch (extract32(s->volatile_cfg, 6, 2)) {
+ case 1:
+ s->needed_bytes += 6;
+ break;
+ case 2:
+ s->needed_bytes += 8;
+ break;
+ default:
+ s->needed_bytes += 4;
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+ s->pos = 0;
+ s->len = 0;
+ s->state = STATE_COLLECTING_DATA;
+}
+
+static void decode_qio_read_cmd(Flash *s)
+{
+ s->needed_bytes = get_addr_length(s);
+ /* Dummy cycles modeled with bytes writes instead of bits */
+ switch (get_man(s)) {
+ case MAN_WINBOND:
+ s->needed_bytes = 6;
+ break;
+ case MAN_SPANSION:
+ s->needed_bytes += extract32(s->spansion_cr2v,
+ SPANSION_DUMMY_CLK_POS,
+ SPANSION_DUMMY_CLK_LEN
+ );
+ break;
+ case MAN_NUMONYX:
+ s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
+ break;
+ case MAN_MACRONIX:
+ switch (extract32(s->volatile_cfg, 6, 2)) {
+ case 1:
+ s->needed_bytes += 4;
+ break;
+ case 2:
+ s->needed_bytes += 8;
+ break;
+ default:
+ s->needed_bytes += 6;
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+ s->pos = 0;
+ s->len = 0;
+ s->state = STATE_COLLECTING_DATA;
+}
+
static void decode_new_cmd(Flash *s, uint32_t value)
{
s->cmd_in_progress = value;
@@ -756,51 +861,17 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case DOR4:
case QOR:
case QOR4:
- s->needed_bytes = get_addr_length(s);
- switch (get_man(s)) {
- case MAN_NUMONYX:
- s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
- break;
- default:
- break;
- }
- s->pos = 0;
- s->len = 0;
- s->state = STATE_COLLECTING_DATA;
+ decode_fast_read_cmd(s);
break;
case DIOR:
case DIOR4:
- switch (get_man(s)) {
- case MAN_WINBOND:
- case MAN_SPANSION:
- s->needed_bytes = 4;
- break;
- default:
- s->needed_bytes = get_addr_length(s);
- /* Dummy cycles modeled with bytes writes instead of bits */
- s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
- }
- s->pos = 0;
- s->len = 0;
- s->state = STATE_COLLECTING_DATA;
+ decode_dio_read_cmd(s);
break;
case QIOR:
case QIOR4:
- switch (get_man(s)) {
- case MAN_WINBOND:
- case MAN_SPANSION:
- s->needed_bytes = 6;
- break;
- default:
- s->needed_bytes = get_addr_length(s);
- /* Dummy cycles modeled with bytes writes instead of bits */
- s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
- }
- s->pos = 0;
- s->len = 0;
- s->state = STATE_COLLECTING_DATA;
+ decode_qio_read_cmd(s);
break;
case WRSR:
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* Re: [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes.
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes marcin.krzeminski
@ 2016-06-17 12:30 ` Cédric Le Goater
2016-06-24 7:53 ` Krzeminski, Marcin (Nokia - PL/Wroclaw)
0 siblings, 1 reply; 15+ messages in thread
From: Cédric Le Goater @ 2016-06-17 12:30 UTC (permalink / raw)
To: marcin.krzeminski, qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, peter.maydell, clg
On 06/17/2016 12:28 PM, marcin.krzeminski@nokia.com wrote:
> From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
>
> Support for Spansion and Macronix flashes.
> Additionally Numonyx(Micron) moved from default
> in fast read commands family. Also moved fast read
> command decoding to functions.
>
> Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Thanks, it looks better.
C.
> ---
> hw/block/m25p80.c | 145 ++++++++++++++++++++++++++++++++++++++++--------------
> 1 file changed, 108 insertions(+), 37 deletions(-)
>
> diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> index 21998db..f40fa99 100644
> --- a/hw/block/m25p80.c
> +++ b/hw/block/m25p80.c
> @@ -719,6 +719,111 @@ static void reset_memory(Flash *s)
> DB_PRINT_L(0, "Reset done.\n");
> }
>
> +static void decode_fast_read_cmd(Flash *s)
> +{
> + s->needed_bytes = get_addr_length(s);
> + switch (get_man(s)) {
> + /* Dummy cycles - modeled with bytes writes instead of bits */
> + case MAN_NUMONYX:
> + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> + break;
> + case MAN_MACRONIX:
> + if (extract32(s->volatile_cfg, 6, 2) == 1) {
> + s->needed_bytes += 6;
> + } else {
> + s->needed_bytes += 8;
> + }
> + break;
> + case MAN_SPANSION:
> + s->needed_bytes += extract32(s->spansion_cr2v,
> + SPANSION_DUMMY_CLK_POS,
> + SPANSION_DUMMY_CLK_LEN
> + );
> + break;
> + default:
> + break;
> + }
> + s->pos = 0;
> + s->len = 0;
> + s->state = STATE_COLLECTING_DATA;
> +}
> +
> +static void decode_dio_read_cmd(Flash *s)
> +{
> + s->needed_bytes = get_addr_length(s);
> + /* Dummy cycles modeled with bytes writes instead of bits */
> + switch (get_man(s)) {
> + case MAN_WINBOND:
> + s->needed_bytes = 4;
> + break;
> + case MAN_SPANSION:
> + s->needed_bytes += extract32(s->spansion_cr2v,
> + SPANSION_DUMMY_CLK_POS,
> + SPANSION_DUMMY_CLK_LEN
> + );
> + break;
> + case MAN_NUMONYX:
> + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> + break;
> + case MAN_MACRONIX:
> + switch (extract32(s->volatile_cfg, 6, 2)) {
> + case 1:
> + s->needed_bytes += 6;
> + break;
> + case 2:
> + s->needed_bytes += 8;
> + break;
> + default:
> + s->needed_bytes += 4;
> + break;
> + }
> + break;
> + default:
> + break;
> + }
> + s->pos = 0;
> + s->len = 0;
> + s->state = STATE_COLLECTING_DATA;
> +}
> +
> +static void decode_qio_read_cmd(Flash *s)
> +{
> + s->needed_bytes = get_addr_length(s);
> + /* Dummy cycles modeled with bytes writes instead of bits */
> + switch (get_man(s)) {
> + case MAN_WINBOND:
> + s->needed_bytes = 6;
> + break;
> + case MAN_SPANSION:
> + s->needed_bytes += extract32(s->spansion_cr2v,
> + SPANSION_DUMMY_CLK_POS,
> + SPANSION_DUMMY_CLK_LEN
> + );
> + break;
> + case MAN_NUMONYX:
> + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> + break;
> + case MAN_MACRONIX:
> + switch (extract32(s->volatile_cfg, 6, 2)) {
> + case 1:
> + s->needed_bytes += 4;
> + break;
> + case 2:
> + s->needed_bytes += 8;
> + break;
> + default:
> + s->needed_bytes += 6;
> + break;
> + }
> + break;
> + default:
> + break;
> + }
> + s->pos = 0;
> + s->len = 0;
> + s->state = STATE_COLLECTING_DATA;
> +}
> +
> static void decode_new_cmd(Flash *s, uint32_t value)
> {
> s->cmd_in_progress = value;
> @@ -756,51 +861,17 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> case DOR4:
> case QOR:
> case QOR4:
> - s->needed_bytes = get_addr_length(s);
> - switch (get_man(s)) {
> - case MAN_NUMONYX:
> - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> - break;
> - default:
> - break;
> - }
> - s->pos = 0;
> - s->len = 0;
> - s->state = STATE_COLLECTING_DATA;
> + decode_fast_read_cmd(s);
> break;
>
> case DIOR:
> case DIOR4:
> - switch (get_man(s)) {
> - case MAN_WINBOND:
> - case MAN_SPANSION:
> - s->needed_bytes = 4;
> - break;
> - default:
> - s->needed_bytes = get_addr_length(s);
> - /* Dummy cycles modeled with bytes writes instead of bits */
> - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> - }
> - s->pos = 0;
> - s->len = 0;
> - s->state = STATE_COLLECTING_DATA;
> + decode_dio_read_cmd(s);
> break;
>
> case QIOR:
> case QIOR4:
> - switch (get_man(s)) {
> - case MAN_WINBOND:
> - case MAN_SPANSION:
> - s->needed_bytes = 6;
> - break;
> - default:
> - s->needed_bytes = get_addr_length(s);
> - /* Dummy cycles modeled with bytes writes instead of bits */
> - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> - }
> - s->pos = 0;
> - s->len = 0;
> - s->state = STATE_COLLECTING_DATA;
> + decode_qio_read_cmd(s);
> break;
>
> case WRSR:
>
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes.
2016-06-17 12:30 ` Cédric Le Goater
@ 2016-06-24 7:53 ` Krzeminski, Marcin (Nokia - PL/Wroclaw)
0 siblings, 0 replies; 15+ messages in thread
From: Krzeminski, Marcin (Nokia - PL/Wroclaw) @ 2016-06-24 7:53 UTC (permalink / raw)
To: Cédric Le Goater, qemu-devel@nongnu.org
Cc: crosthwaitepeter@gmail.com, pawel.lenkow@itlen.com,
peter.maydell@linaro.org, clg@fr.ibm.com
> -----Original Message-----
> From: Cédric Le Goater [mailto:clg@kaod.org]
> Sent: Friday, June 17, 2016 2:31 PM
> To: Krzeminski, Marcin (Nokia - PL/Wroclaw)
> <marcin.krzeminski@nokia.com>; qemu-devel@nongnu.org
> Cc: crosthwaitepeter@gmail.com; pawel.lenkow@itlen.com;
> peter.maydell@linaro.org; clg@fr.ibm.com
> Subject: Re: [PATCH v2 08/10] m25p80: Fast read commands family changes.
>
> On 06/17/2016 12:28 PM, marcin.krzeminski@nokia.com wrote:
> > From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
> >
> > Support for Spansion and Macronix flashes.
> > Additionally Numonyx(Micron) moved from default in fast read commands
> > family. Also moved fast read command decoding to functions.
> >
> > Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
>
> Reviewed-by: Cédric Le Goater <clg@kaod.org>
>
> Thanks, it looks better.
>
> C.
>
> > ---
> > hw/block/m25p80.c | 145
> > ++++++++++++++++++++++++++++++++++++++++--------------
> > 1 file changed, 108 insertions(+), 37 deletions(-)
> >
> > diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c index
> > 21998db..f40fa99 100644
> > --- a/hw/block/m25p80.c
> > +++ b/hw/block/m25p80.c
> > @@ -719,6 +719,111 @@ static void reset_memory(Flash *s)
> > DB_PRINT_L(0, "Reset done.\n");
> > }
> >
> > +static void decode_fast_read_cmd(Flash *s) {
> > + s->needed_bytes = get_addr_length(s);
> > + switch (get_man(s)) {
> > + /* Dummy cycles - modeled with bytes writes instead of bits */
> > + case MAN_NUMONYX:
> > + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > + break;
> > + case MAN_MACRONIX:
> > + if (extract32(s->volatile_cfg, 6, 2) == 1) {
> > + s->needed_bytes += 6;
> > + } else {
> > + s->needed_bytes += 8;
> > + }
> > + break;
> > + case MAN_SPANSION:
> > + s->needed_bytes += extract32(s->spansion_cr2v,
> > + SPANSION_DUMMY_CLK_POS,
> > + SPANSION_DUMMY_CLK_LEN
> > + );
> > + break;
> > + default:
> > + break;
> > + }
> > + s->pos = 0;
> > + s->len = 0;
> > + s->state = STATE_COLLECTING_DATA; }
> > +
> > +static void decode_dio_read_cmd(Flash *s) {
> > + s->needed_bytes = get_addr_length(s);
> > + /* Dummy cycles modeled with bytes writes instead of bits */
> > + switch (get_man(s)) {
> > + case MAN_WINBOND:
> > + s->needed_bytes = 4;
> > + break;
> > + case MAN_SPANSION:
> > + s->needed_bytes += extract32(s->spansion_cr2v,
> > + SPANSION_DUMMY_CLK_POS,
> > + SPANSION_DUMMY_CLK_LEN
> > + );
Here and in QuadIO function handling of read mode bytes is missing.
I will add it in v3.
Thanks for review.
Regards,
Marcin
> > + break;
> > + case MAN_NUMONYX:
> > + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > + break;
> > + case MAN_MACRONIX:
> > + switch (extract32(s->volatile_cfg, 6, 2)) {
> > + case 1:
> > + s->needed_bytes += 6;
> > + break;
> > + case 2:
> > + s->needed_bytes += 8;
> > + break;
> > + default:
> > + s->needed_bytes += 4;
> > + break;
> > + }
> > + break;
> > + default:
> > + break;
> > + }
> > + s->pos = 0;
> > + s->len = 0;
> > + s->state = STATE_COLLECTING_DATA; }
> > +
> > +static void decode_qio_read_cmd(Flash *s) {
> > + s->needed_bytes = get_addr_length(s);
> > + /* Dummy cycles modeled with bytes writes instead of bits */
> > + switch (get_man(s)) {
> > + case MAN_WINBOND:
> > + s->needed_bytes = 6;
> > + break;
> > + case MAN_SPANSION:
> > + s->needed_bytes += extract32(s->spansion_cr2v,
> > + SPANSION_DUMMY_CLK_POS,
> > + SPANSION_DUMMY_CLK_LEN
> > + );
> > + break;
> > + case MAN_NUMONYX:
> > + s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > + break;
> > + case MAN_MACRONIX:
> > + switch (extract32(s->volatile_cfg, 6, 2)) {
> > + case 1:
> > + s->needed_bytes += 4;
> > + break;
> > + case 2:
> > + s->needed_bytes += 8;
> > + break;
> > + default:
> > + s->needed_bytes += 6;
> > + break;
> > + }
> > + break;
> > + default:
> > + break;
> > + }
> > + s->pos = 0;
> > + s->len = 0;
> > + s->state = STATE_COLLECTING_DATA; }
> > +
> > static void decode_new_cmd(Flash *s, uint32_t value) {
> > s->cmd_in_progress = value;
> > @@ -756,51 +861,17 @@ static void decode_new_cmd(Flash *s, uint32_t
> value)
> > case DOR4:
> > case QOR:
> > case QOR4:
> > - s->needed_bytes = get_addr_length(s);
> > - switch (get_man(s)) {
> > - case MAN_NUMONYX:
> > - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > - break;
> > - default:
> > - break;
> > - }
> > - s->pos = 0;
> > - s->len = 0;
> > - s->state = STATE_COLLECTING_DATA;
> > + decode_fast_read_cmd(s);
> > break;
> >
> > case DIOR:
> > case DIOR4:
> > - switch (get_man(s)) {
> > - case MAN_WINBOND:
> > - case MAN_SPANSION:
> > - s->needed_bytes = 4;
> > - break;
> > - default:
> > - s->needed_bytes = get_addr_length(s);
> > - /* Dummy cycles modeled with bytes writes instead of bits */
> > - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > - }
> > - s->pos = 0;
> > - s->len = 0;
> > - s->state = STATE_COLLECTING_DATA;
> > + decode_dio_read_cmd(s);
> > break;
> >
> > case QIOR:
> > case QIOR4:
> > - switch (get_man(s)) {
> > - case MAN_WINBOND:
> > - case MAN_SPANSION:
> > - s->needed_bytes = 6;
> > - break;
> > - default:
> > - s->needed_bytes = get_addr_length(s);
> > - /* Dummy cycles modeled with bytes writes instead of bits */
> > - s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
> > - }
> > - s->pos = 0;
> > - s->len = 0;
> > - s->state = STATE_COLLECTING_DATA;
> > + decode_qio_read_cmd(s);
> > break;
> >
> > case WRSR:
> >
^ permalink raw reply [flat|nested] 15+ messages in thread
* [Qemu-devel] [PATCH v2 09/10] m25p80: New flash devices.
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (7 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 08/10] m25p80: Fast read commands family changes marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 10/10] m25p80.c: Fix WINBOND fast read command handling marcin.krzeminski
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Macronix: mx66u51235f and mx66u1g45g
Micron: mt25ql01g and mt25qu01g
Spansion: s25fs512s and s70fs01gs
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
---
hw/block/m25p80.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index f40fa99..3798152 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -192,6 +192,8 @@ static const FlashPartInfo known_devices[] = {
{ INFO("mx25l12855e", 0xc22618, 0, 64 << 10, 256, 0) },
{ INFO("mx25l25635e", 0xc22019, 0, 64 << 10, 512, 0) },
{ INFO("mx25l25655e", 0xc22619, 0, 64 << 10, 512, 0) },
+ { INFO("mx66u51235f", 0xc2253a, 0, 64 << 10, 1024, ER_4K | ER_32K) },
+ { INFO("mx66u1g45g", 0xc2253b, 0, 64 << 10, 2048, ER_4K | ER_32K) },
/* Micron */
{ INFO("n25q032a11", 0x20bb16, 0, 64 << 10, 64, ER_4K) },
@@ -202,6 +204,11 @@ static const FlashPartInfo known_devices[] = {
{ INFO("n25q128a13", 0x20ba18, 0, 64 << 10, 256, ER_4K) },
{ INFO("n25q256a11", 0x20bb19, 0, 64 << 10, 512, ER_4K) },
{ INFO("n25q256a13", 0x20ba19, 0, 64 << 10, 512, ER_4K) },
+ { INFO("n25q128", 0x20ba18, 0, 64 << 10, 256, 0) },
+ { INFO("n25q256a", 0x20ba19, 0, 64 << 10, 512, ER_4K) },
+ { INFO("n25q512a", 0x20ba20, 0, 64 << 10, 1024, ER_4K) },
+ { INFO("mt25ql01g", 0x20ba21, 0, 64 << 10, 2048, ER_4K) },
+ { INFO("mt25qu01g", 0x20bb21, 0, 64 << 10, 2048, ER_4K) },
/* Spansion -- single (large) sector size only, at least
* for the chips listed here (without boot sectors).
@@ -210,8 +217,8 @@ static const FlashPartInfo known_devices[] = {
{ INFO("s25sl064p", 0x010216, 0x4d00, 64 << 10, 128, ER_4K) },
{ INFO("s25fl256s0", 0x010219, 0x4d00, 256 << 10, 128, 0) },
{ INFO("s25fl256s1", 0x010219, 0x4d01, 64 << 10, 512, 0) },
- { INFO("s25fl512s", 0x010220, 0x4d00, 256 << 10, 256, 0) },
- { INFO("s70fl01gs", 0x010221, 0x4d00, 256 << 10, 256, 0) },
+ { INFO6("s25fl512s", 0x010220, 0x4d0080, 256 << 10, 256, 0) },
+ { INFO6("s70fl01gs", 0x010221, 0x4d0080, 256 << 10, 512, 0) },
{ INFO("s25sl12800", 0x012018, 0x0300, 256 << 10, 64, 0) },
{ INFO("s25sl12801", 0x012018, 0x0301, 64 << 10, 256, 0) },
{ INFO("s25fl129p0", 0x012018, 0x4d00, 256 << 10, 64, 0) },
@@ -224,6 +231,10 @@ static const FlashPartInfo known_devices[] = {
{ INFO("s25fl016k", 0xef4015, 0, 64 << 10, 32, ER_4K | ER_32K) },
{ INFO("s25fl064k", 0xef4017, 0, 64 << 10, 128, ER_4K | ER_32K) },
+ /* Spansion -- boot sectors support */
+ { INFO6("s25fs512s", 0x010220, 0x4d0081, 256 << 10, 256, 0) },
+ { INFO6("s70fs01gs", 0x010221, 0x4d0081, 256 << 10, 512, 0) },
+
/* SST -- large erase sizes are "overlays", "sectors" are 4<< 10 */
{ INFO("sst25vf040b", 0xbf258d, 0, 64 << 10, 8, ER_4K) },
{ INFO("sst25vf080b", 0xbf258e, 0, 64 << 10, 16, ER_4K) },
@@ -274,10 +285,6 @@ static const FlashPartInfo known_devices[] = {
{ INFO("w25q80", 0xef5014, 0, 64 << 10, 16, ER_4K) },
{ INFO("w25q80bl", 0xef4014, 0, 64 << 10, 16, ER_4K) },
{ INFO("w25q256", 0xef4019, 0, 64 << 10, 512, ER_4K) },
-
- { INFO("n25q128", 0x20ba18, 0, 64 << 10, 256, 0) },
- { INFO("n25q256a", 0x20ba19, 0, 64 << 10, 512, ER_4K) },
- { INFO("n25q512a", 0x20ba20, 0, 64 << 10, 1024, ER_4K) },
};
typedef enum {
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [Qemu-devel] [PATCH v2 10/10] m25p80.c: Fix WINBOND fast read command handling
2016-06-17 10:28 [Qemu-devel] [PATCH v2 00/10] m25p80: Add new 512Mbit and 1Gbit devices marcin.krzeminski
` (8 preceding siblings ...)
2016-06-17 10:28 ` [Qemu-devel] [PATCH v2 09/10] m25p80: New flash devices marcin.krzeminski
@ 2016-06-17 10:28 ` marcin.krzeminski
9 siblings, 0 replies; 15+ messages in thread
From: marcin.krzeminski @ 2016-06-17 10:28 UTC (permalink / raw)
To: qemu-devel
Cc: crosthwaitepeter, pawel.lenkow, rfsw-patches, peter.maydell, clg,
clg
From: Marcin Krzeminski <marcin.krzeminski@nokia.com>
This commit fix obvious bug in WINBOND command handling.
Datasheet states that default dummy cycles is 8 so fix it.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
---
hw/block/m25p80.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 3798152..5456c1d 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -731,6 +731,9 @@ static void decode_fast_read_cmd(Flash *s)
s->needed_bytes = get_addr_length(s);
switch (get_man(s)) {
/* Dummy cycles - modeled with bytes writes instead of bits */
+ case MAN_WINBOND:
+ s->needed_bytes += 8;
+ break;
case MAN_NUMONYX:
s->needed_bytes += extract32(s->volatile_cfg, 4, 4);
break;
@@ -761,7 +764,7 @@ static void decode_dio_read_cmd(Flash *s)
/* Dummy cycles modeled with bytes writes instead of bits */
switch (get_man(s)) {
case MAN_WINBOND:
- s->needed_bytes = 4;
+ s->needed_bytes += 8;
break;
case MAN_SPANSION:
s->needed_bytes += extract32(s->spansion_cr2v,
@@ -799,7 +802,7 @@ static void decode_qio_read_cmd(Flash *s)
/* Dummy cycles modeled with bytes writes instead of bits */
switch (get_man(s)) {
case MAN_WINBOND:
- s->needed_bytes = 6;
+ s->needed_bytes += 8;
break;
case MAN_SPANSION:
s->needed_bytes += extract32(s->spansion_cr2v,
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread