From: Aurelien Jarno <aurelien@aurel32.net>
To: Alexander Voropay <alec@nwpi.ru>, qemu-devel@nongnu.org
Subject: Re: [Qemu-devel] [PATCH] Change the 82371SB PCI-to-ISA bridge into a82371EB
Date: Wed, 10 Jan 2007 01:54:28 +0100 [thread overview]
Message-ID: <20070110005428.GA12917@farad.aurel32.net> (raw)
In-Reply-To: <3c9801c73418$7fe43470$e90d11ac@spb.in.rosprint.ru>
On Tue, Jan 09, 2007 at 09:03:01PM +0300, Alexander Voropay wrote:
> "Aurelien Jarno" <aurelien@aurel32.net> wrote:
>
> >This patch changes the 82371SB PCI-to-ISA bridge into a 82371EB.
> >
> >Note that the ACPI controller
> >implemented in QEMU is already a 82371EB.
>
> Shouldn't we also change all "piix3" names to "piix4" ?
>
> [qemu]$ find . -type f | xargs grep "piix3" | wc -l
> 18
>
>
You are probably right for this device, but note that the USB and the
IDE controller are still PIIX3. And this corresponds to the emulated
devices. Ideally it would be nice to also change them into PIIX4 by
implementing the missing features. Some of the missing features are
really cool, like DMA support in IDE controller.
Please find below a new patch that also changes the name of the ISA
bridge to piix4. That introduces a sequence in the patches, it needs to
be applied after the patch "devfn number for the PIIX3 southbridge".
Bye,
Aurelien
This patch changes the 82371SB PCI-to-ISA bridge into a 82371EB. There
are no differences in the implementation, but the Malta platform needs
this device as there are some PCI fixup in the Linux kernel.
This should be supported without problem by the i386 and x86_64 targets
as there is no standard PC hardware. Note that the ACPI controller
implemented in QEMU is already a 82371EB.
diff -Nurd qemu.orig/hw/pc.c qemu/hw/pc.c
--- qemu.orig/hw/pc.c 2007-01-10 01:46:23.000000000 +0100
+++ qemu/hw/pc.c 2007-01-10 01:47:47.000000000 +0100
@@ -454,7 +454,7 @@
unsigned long bios_offset, vga_bios_offset, option_rom_offset;
int bios_size, isa_bios_size;
PCIBus *pci_bus;
- int piix3_devfn = -1;
+ int piix4_devfn = -1;
CPUState *env;
NICInfo *nd;
@@ -599,7 +599,7 @@
if (pci_enabled) {
pci_bus = i440fx_init(&i440fx_state);
- piix3_devfn = piix3_init(pci_bus, -1);
+ piix4_devfn = piix4_init(pci_bus, -1);
} else {
pci_bus = NULL;
}
@@ -676,7 +676,7 @@
}
if (pci_enabled) {
- pci_piix3_ide_init(pci_bus, bs_table, piix3_devfn + 1);
+ pci_piix3_ide_init(pci_bus, bs_table, piix4_devfn + 1);
} else {
for(i = 0; i < 2; i++) {
isa_ide_init(ide_iobase[i], ide_iobase2[i], ide_irq[i],
@@ -695,11 +695,11 @@
cmos_init(ram_size, boot_device, bs_table);
if (pci_enabled && usb_enabled) {
- usb_uhci_init(pci_bus, piix3_devfn + 2);
+ usb_uhci_init(pci_bus, piix4_devfn + 2);
}
if (pci_enabled && acpi_enabled) {
- piix4_pm_init(pci_bus, piix3_devfn + 3);
+ piix4_pm_init(pci_bus, piix4_devfn + 3);
}
if (i440fx_state) {
diff -Nurd qemu.orig/hw/piix_pci.c qemu/hw/piix_pci.c
--- qemu.orig/hw/piix_pci.c 2007-01-10 01:46:23.000000000 +0100
+++ qemu/hw/piix_pci.c 2007-01-10 01:48:32.000000000 +0100
@@ -40,7 +40,7 @@
return s->config_reg;
}
-static void piix3_set_irq(void *pic, int irq_num, int level);
+static void piix4_set_irq(void *pic, int irq_num, int level);
/* return the global irq number corresponding to a given device irq
pin. We could also use the bus number to have a more precise
@@ -162,7 +162,7 @@
I440FXState *s;
s = qemu_mallocz(sizeof(I440FXState));
- b = pci_register_bus(piix3_set_irq, pci_slot_get_pirq, NULL, 0, 4);
+ b = pci_register_bus(piix4_set_irq, pci_slot_get_pirq, NULL, 0, 4);
s->bus = b;
register_ioport_write(0xcf8, 4, 4, i440fx_addr_writel, s);
@@ -196,14 +196,14 @@
/* PIIX3 PCI to ISA bridge */
-PCIDevice *piix3_dev;
+PCIDevice *piix4_dev;
/* just used for simpler irq handling. */
#define PCI_IRQ_WORDS ((PCI_DEVICES_MAX + 31) / 32)
static int pci_irq_levels[4];
-static void piix3_set_irq(void *pic, int irq_num, int level)
+static void piix4_set_irq(void *pic, int irq_num, int level)
{
int i, pic_irq, pic_level;
@@ -211,20 +211,20 @@
/* now we change the pic irq level according to the piix irq mappings */
/* XXX: optimize */
- pic_irq = piix3_dev->config[0x60 + irq_num];
+ pic_irq = piix4_dev->config[0x60 + irq_num];
if (pic_irq < 16) {
/* The pic level is the logical OR of all the PCI irqs mapped
to it */
pic_level = 0;
for (i = 0; i < 4; i++) {
- if (pic_irq == piix3_dev->config[0x60 + i])
+ if (pic_irq == piix4_dev->config[0x60 + i])
pic_level |= pci_irq_levels[i];
}
pic_set_irq(pic_irq, pic_level);
}
}
-static void piix3_reset(PCIDevice *d)
+static void piix4_reset(PCIDevice *d)
{
uint8_t *pci_conf = d->config;
@@ -273,26 +273,26 @@
return pci_device_load(d, f);
}
-int piix3_init(PCIBus *bus, int devfn)
+int piix4_init(PCIBus *bus, int devfn)
{
PCIDevice *d;
uint8_t *pci_conf;
- d = pci_register_device(bus, "PIIX3", sizeof(PCIDevice),
+ d = pci_register_device(bus, "PIIX4", sizeof(PCIDevice),
devfn, NULL, NULL);
- register_savevm("PIIX3", 0, 2, piix_save, piix_load, d);
+ register_savevm("PIIX4", 0, 2, piix_save, piix_load, d);
- piix3_dev = d;
+ piix4_dev = d;
pci_conf = d->config;
pci_conf[0x00] = 0x86; // Intel
pci_conf[0x01] = 0x80;
- pci_conf[0x02] = 0x00; // 82371SB PIIX3 PCI-to-ISA bridge (Step A1)
- pci_conf[0x03] = 0x70;
+ pci_conf[0x02] = 0x10; // 82371AB/EB/MB PIIX4 PCI-to-ISA bridge
+ pci_conf[0x03] = 0x71;
pci_conf[0x0a] = 0x01; // class_sub = PCI_ISA
pci_conf[0x0b] = 0x06; // class_base = PCI_bridge
pci_conf[0x0e] = 0x80; // header_type = PCI_multifunction, generic
- piix3_reset(d);
+ piix4_reset(d);
return d->devfn;
}
diff -Nurd qemu.orig/vl.h qemu/vl.h
--- qemu.orig/vl.h 2007-01-10 01:46:23.000000000 +0100
+++ qemu/vl.h 2007-01-10 01:47:59.000000000 +0100
@@ -821,7 +821,7 @@
/* piix_pci.c */
PCIBus *i440fx_init(PCIDevice **pi440fx_state);
void i440fx_set_smm(PCIDevice *d, int val);
-int piix3_init(PCIBus *bus, int devfn);
+int piix4_init(PCIBus *bus, int devfn);
void i440fx_init_memory_mappings(PCIDevice *d);
/* openpic.c */
--
.''`. Aurelien Jarno | GPG: 1024D/F1BCDB73
: :' : Debian developer | Electrical Engineer
`. `' aurel32@debian.org | aurelien@aurel32.net
`- people.debian.org/~aurel32 | www.aurel32.net
next prev parent reply other threads:[~2007-01-10 0:54 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-01-09 15:44 [Qemu-devel] [PATCH] Change the 82371SB PCI-to-ISA bridge into a 82371EB Aurelien Jarno
2007-01-09 18:03 ` [Qemu-devel] [PATCH] Change the 82371SB PCI-to-ISA bridge into a82371EB Alexander Voropay
2007-01-10 0:54 ` Aurelien Jarno [this message]
2007-01-11 20:00 ` Fabrice Bellard
2007-01-11 22:13 ` Aurelien Jarno
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070110005428.GA12917@farad.aurel32.net \
--to=aurelien@aurel32.net \
--cc=alec@nwpi.ru \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).