From: Aurelien Jarno <aurelien@aurel32.net>
To: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: qemu-devel@nongnu.org
Subject: Re: [Qemu-devel] [PATCH V4] SH7750/51: add register BCR3, BCR4, PCR, RTCOR, RTCNT, RTCSR, SDMR2, SDMR3 and fix BCR2 support
Date: Sat, 7 Feb 2009 16:19:11 +0100 [thread overview]
Message-ID: <20090207151911.GD6533@volta.aurel32.net> (raw)
In-Reply-To: <1229643194-24014-1-git-send-email-plagnioj@jcrosoft.com>
On Fri, Dec 19, 2008 at 12:33:14AM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> ---
> Since V2:
> As disscuss with Paul Mundt
> Just bail out with a bogus access.
> Trying to access bcr3 or bcr4 or non R revision is not something an address
> error exception woulbe generated for
>
> Since V3:
> Fix forgeedt invert of the bcr3/4 check
>
> Best Regards,
> J.
> hw/sh7750.c | 52 ++++++++++++++++++++++++++++++++++++++---------
> hw/sh7750_regnames.c | 4 +-
> hw/sh7750_regs.h | 13 ++++++++++-
> target-sh4/cpu.h | 1 +
> target-sh4/translate.c | 2 +
> 5 files changed, 58 insertions(+), 14 deletions(-)
Thanks, applied.
> diff --git a/hw/sh7750.c b/hw/sh7750.c
> index 4d1a806..e09fcda 100644
> --- a/hw/sh7750.c
> +++ b/hw/sh7750.c
> @@ -42,8 +42,12 @@ typedef struct SH7750State {
> uint32_t periph_freq;
> /* SDRAM controller */
> uint32_t bcr1;
> - uint32_t bcr2;
> + uint16_t bcr2;
> + uint16_t bcr3;
> + uint32_t bcr4;
> uint16_t rfcr;
> + /* PCMCIA controller */
> + uint16_t pcr;
> /* IO ports */
> uint16_t gpioic;
> uint32_t pctra;
> @@ -66,7 +70,10 @@ typedef struct SH7750State {
> struct intc_desc intc;
> } SH7750State;
>
> -
> +static int inline has_bcr3_and_bcr4(SH7750State * s)
> +{
> + return (s->cpu->features & SH_FEATURE_BCR3_AND_BCR4);
> +}
> /**********************************************************************
> I/O ports
> **********************************************************************/
> @@ -211,8 +218,14 @@ static uint32_t sh7750_mem_readw(void *opaque, target_phys_addr_t addr)
> switch (addr) {
> case SH7750_BCR2_A7:
> return s->bcr2;
> + case SH7750_BCR3_A7:
> + if(!has_bcr3_and_bcr4(s))
> + error_access("word read", addr);
> + return s->bcr3;
> case SH7750_FRQCR_A7:
> return 0;
> + case SH7750_PCR_A7:
> + return s->pcr;
> case SH7750_RFCR_A7:
> fprintf(stderr,
> "Read access to refresh count register, incrementing\n");
> @@ -221,6 +234,11 @@ static uint32_t sh7750_mem_readw(void *opaque, target_phys_addr_t addr)
> return porta_lines(s);
> case SH7750_PDTRB_A7:
> return portb_lines(s);
> + case SH7750_RTCOR_A7:
> + case SH7750_RTCNT_A7:
> + case SH7750_RTCSR_A7:
> + ignore_access("word read", addr);
> + return 0;
> default:
> error_access("word read", addr);
> assert(0);
> @@ -235,6 +253,9 @@ static uint32_t sh7750_mem_readl(void *opaque, target_phys_addr_t addr)
> case SH7750_BCR1_A7:
> return s->bcr1;
> case SH7750_BCR4_A7:
> + if(!has_bcr3_and_bcr4(s))
> + error_access("long read", addr);
> + return s->bcr4;
> case SH7750_WCR1_A7:
> case SH7750_WCR2_A7:
> case SH7750_WCR3_A7:
> @@ -271,19 +292,19 @@ static uint32_t sh7750_mem_readl(void *opaque, target_phys_addr_t addr)
> }
> }
>
> +#define is_in_sdrmx(a, x) (a >= SH7750_SDMR ## x ## _A7 \
> + && a <= (SH7750_SDMR ## x ## _A7 + SH7750_SDMR ## x ## _REGNB))
> static void sh7750_mem_writeb(void *opaque, target_phys_addr_t addr,
> uint32_t mem_value)
> {
> - switch (addr) {
> - /* PRECHARGE ? XXXXX */
> - case SH7750_PRECHARGE0_A7:
> - case SH7750_PRECHARGE1_A7:
> +
> + if (is_in_sdrmx(addr, 2) || is_in_sdrmx(addr, 3)) {
> ignore_access("byte write", addr);
> return;
> - default:
> - error_access("byte write", addr);
> - assert(0);
> }
> +
> + error_access("byte write", addr);
> + assert(0);
> }
>
> static void sh7750_mem_writew(void *opaque, target_phys_addr_t addr,
> @@ -298,8 +319,15 @@ static void sh7750_mem_writew(void *opaque, target_phys_addr_t addr,
> s->bcr2 = mem_value;
> return;
> case SH7750_BCR3_A7:
> - case SH7750_RTCOR_A7:
> + if(!has_bcr3_and_bcr4(s))
> + error_access("word write", addr);
> + s->bcr3 = mem_value;
> + return;
> + case SH7750_PCR_A7:
> + s->pcr = mem_value;
> + return;
> case SH7750_RTCNT_A7:
> + case SH7750_RTCOR_A7:
> case SH7750_RTCSR_A7:
> ignore_access("word write", addr);
> return;
> @@ -343,6 +371,10 @@ static void sh7750_mem_writel(void *opaque, target_phys_addr_t addr,
> s->bcr1 = mem_value;
> return;
> case SH7750_BCR4_A7:
> + if(!has_bcr3_and_bcr4(s))
> + error_access("long write", addr);
> + s->bcr4 = mem_value;
> + return;
> case SH7750_WCR1_A7:
> case SH7750_WCR2_A7:
> case SH7750_WCR3_A7:
> diff --git a/hw/sh7750_regnames.c b/hw/sh7750_regnames.c
> index 51283c9..4928151 100644
> --- a/hw/sh7750_regnames.c
> +++ b/hw/sh7750_regnames.c
> @@ -79,8 +79,8 @@ static regname_t regnames[] = {
> REGNAME(SH7750_ICR_A7)
> REGNAME(SH7750_BCR3_A7)
> REGNAME(SH7750_BCR4_A7)
> - REGNAME(SH7750_PRECHARGE0_A7)
> - REGNAME(SH7750_PRECHARGE1_A7) {(uint32_t) - 1, 0}
> + REGNAME(SH7750_SDMR2_A7)
> + REGNAME(SH7750_SDMR3_A7) {(uint32_t) - 1, 0}
> };
>
> const char *regname(uint32_t addr)
> diff --git a/hw/sh7750_regs.h b/hw/sh7750_regs.h
> index c8fb328..5a23a2c 100644
> --- a/hw/sh7750_regs.h
> +++ b/hw/sh7750_regs.h
> @@ -979,6 +979,17 @@
>
> #define SH7750_RFCR_KEY 0xA400 /* RFCR write key */
>
> +/* Synchronous DRAM mode registers - SDMR */
> +#define SH7750_SDMR2_REGOFS 0x900000 /* base offset */
> +#define SH7750_SDMR2_REGNB 0x0FFC /* nb of register */
> +#define SH7750_SDMR2 SH7750_P4_REG32(SH7750_SDMR2_REGOFS)
> +#define SH7750_SDMR2_A7 SH7750_A7_REG32(SH7750_SDMR2_REGOFS)
> +
> +#define SH7750_SDMR3_REGOFS 0x940000 /* offset */
> +#define SH7750_SDMR3_REGNB 0x0FFC /* nb of register */
> +#define SH7750_SDMR3 SH7750_P4_REG32(SH7750_SDMR3_REGOFS)
> +#define SH7750_SDMR3_A7 SH7750_A7_REG32(SH7750_SDMR3_REGOFS)
> +
> /*
> * Direct Memory Access Controller (DMAC)
> */
> @@ -1262,7 +1273,5 @@
> */
> #define SH7750_BCR3_A7 0x1f800050
> #define SH7750_BCR4_A7 0x1e0a00f0
> -#define SH7750_PRECHARGE0_A7 0x1f900088
> -#define SH7750_PRECHARGE1_A7 0x1f940088
>
> #endif
> diff --git a/target-sh4/cpu.h b/target-sh4/cpu.h
> index 226417f..da6b81c 100644
> --- a/target-sh4/cpu.h
> +++ b/target-sh4/cpu.h
> @@ -95,6 +95,7 @@ typedef struct tlb_t {
>
> enum sh_features {
> SH_FEATURE_SH4A = 1,
> + SH_FEATURE_BCR3_AND_BCR4 = 2,
> };
>
> typedef struct CPUSH4State {
> diff --git a/target-sh4/translate.c b/target-sh4/translate.c
> index 2d3981c..ed4a26b 100644
> --- a/target-sh4/translate.c
> +++ b/target-sh4/translate.c
> @@ -217,12 +217,14 @@ static sh4_def_t sh4_defs[] = {
> .pvr = 0x00050000,
> .prr = 0x00000100,
> .cvr = 0x00110000,
> + .features = SH_FEATURE_BCR3_AND_BCR4,
> }, {
> .name = "SH7751R",
> .id = SH_CPU_SH7751R,
> .pvr = 0x04050005,
> .prr = 0x00000113,
> .cvr = 0x00110000, /* Neutered caches, should be 0x20480000 */
> + .features = SH_FEATURE_BCR3_AND_BCR4,
> }, {
> .name = "SH7785",
> .id = SH_CPU_SH7785,
> --
> 1.5.6.5
>
>
>
>
--
Aurelien Jarno GPG: 1024D/F1BCDB73
aurelien@aurel32.net http://www.aurel32.net
prev parent reply other threads:[~2009-02-07 15:22 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-05 11:49 [Qemu-devel] [PATCH] SH7750/51: add register BCR3, NCR4, PCR, RTCOR, RTCNT, RTCSR, SDMR2, SDMR3 and fix BCR2 support Jean-Christophe PLAGNIOL-VILLARD
2008-12-14 11:37 ` Shin-ichiro KAWASAKI
2008-12-14 14:51 ` Jean-Christophe PLAGNIOL-VILLARD
2008-12-14 15:36 ` Shin-ichiro KAWASAKI
2008-12-14 16:37 ` Jean-Christophe PLAGNIOL-VILLARD
2008-12-14 17:24 ` Thiemo Seufer
2008-12-15 0:37 ` Shin-ichiro KAWASAKI
2008-12-15 1:08 ` Thiemo Seufer
2008-12-14 17:28 ` Aurelien Jarno
2008-12-17 9:18 ` [Qemu-devel] [PATCH V2] SH7750/51: add register BCR3, BCR4, " Jean-Christophe PLAGNIOL-VILLARD
2008-12-18 15:51 ` Aurelien Jarno
2008-12-18 21:49 ` [Qemu-devel] [PATCH V3] " Jean-Christophe PLAGNIOL-VILLARD
2008-12-18 23:33 ` [Qemu-devel] [PATCH V4] " Jean-Christophe PLAGNIOL-VILLARD
2009-02-07 15:19 ` Aurelien Jarno [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090207151911.GD6533@volta.aurel32.net \
--to=aurelien@aurel32.net \
--cc=plagnioj@jcrosoft.com \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).