[Qemu-devel] [PATCHv5-repost 1/2] qemu: make cirrus init value pci spec compliant

[Qemu-devel] [PATCHv5-repost 1/2] qemu: make cirrus init value pci spec compliant

[Michael S. Tsirkin]

PCI memory should be disabled at reset, otherwise
we might claim transactions at address 0.
I/O should also be disabled, although for cirrus
it is harmless to enable it as we do not
have I/O bar.

Note: bios fix needed for this patch to work
was already applied:
previously bios incorrently assumed that it does not
need to enable i/o unless device has i/o bar.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
---
 hw/cirrus_vga.c |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/hw/cirrus_vga.c b/hw/cirrus_vga.c
index d76e5bb..e16026f 100644
--- a/hw/cirrus_vga.c
+++ b/hw/cirrus_vga.c
@@ -3231,7 +3231,6 @@ static int pci_cirrus_vga_initfn(PCIDevice *dev)
      /* setup PCI */
      pci_config_set_vendor_id(pci_conf, PCI_VENDOR_ID_CIRRUS);
      pci_config_set_device_id(pci_conf, device_id);
-     pci_conf[0x04] = PCI_COMMAND_IOACCESS | PCI_COMMAND_MEMACCESS;
      pci_config_set_class(pci_conf, PCI_CLASS_DISPLAY_VGA);
      pci_conf[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL;
 
-- 
1.6.5.2.143.g8cc62

[Qemu-devel] [PATCHv5-repost 2/2] qemu: cleanup unused macros in cirrus

[Michael S. Tsirkin]

Cirrus vga has a copy of many PCI macros,
and it doesn't even use them. Clean up.
We also don't need to override header type
as it is NORMAL by default.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
---
 hw/cirrus_vga.c |   35 -----------------------------------
 1 files changed, 0 insertions(+), 35 deletions(-)

diff --git a/hw/cirrus_vga.c b/hw/cirrus_vga.c
index e16026f..8558212 100644
--- a/hw/cirrus_vga.c
+++ b/hw/cirrus_vga.c
@@ -172,40 +172,6 @@
 #define CIRRUS_MMIO_LINEDRAW_MODE     0x39	// byte
 #define CIRRUS_MMIO_BLTSTATUS         0x40	// byte
 
-// PCI 0x04: command(word), 0x06(word): status
-#define PCI_COMMAND_IOACCESS                0x0001
-#define PCI_COMMAND_MEMACCESS               0x0002
-#define PCI_COMMAND_BUSMASTER               0x0004
-#define PCI_COMMAND_SPECIALCYCLE            0x0008
-#define PCI_COMMAND_MEMWRITEINVALID         0x0010
-#define PCI_COMMAND_PALETTESNOOPING         0x0020
-#define PCI_COMMAND_PARITYDETECTION         0x0040
-#define PCI_COMMAND_ADDRESSDATASTEPPING     0x0080
-#define PCI_COMMAND_BACKTOBACKTRANS         0x0200
-// PCI 0x08, 0xff000000 (0x09-0x0b:class,0x08:rev)
-#define PCI_CLASS_BASE_DISPLAY        0x03
-// PCI 0x08, 0x00ff0000
-#define PCI_CLASS_SUB_VGA             0x00
-// PCI 0x0c, 0x00ff0000 (0x0c:cacheline,0x0d:latency,0x0e:headertype,0x0f:Built-in self test)
-// 0x10-0x3f (headertype 00h)
-// PCI 0x10,0x14,0x18,0x1c,0x20,0x24: base address mapping registers
-//   0x10: MEMBASE, 0x14: IOBASE(hard-coded in XFree86 3.x)
-#define PCI_MAP_MEM                 0x0
-#define PCI_MAP_IO                  0x1
-#define PCI_MAP_MEM_ADDR_MASK       (~0xf)
-#define PCI_MAP_IO_ADDR_MASK        (~0x3)
-#define PCI_MAP_MEMFLAGS_32BIT      0x0
-#define PCI_MAP_MEMFLAGS_32BIT_1M   0x1
-#define PCI_MAP_MEMFLAGS_64BIT      0x4
-#define PCI_MAP_MEMFLAGS_CACHEABLE  0x8
-// PCI 0x28: cardbus CIS pointer
-// PCI 0x2c: subsystem vendor id, 0x2e: subsystem id
-// PCI 0x30: expansion ROM base address
-#define PCI_ROMBIOS_ENABLED         0x1
-// PCI 0x34: 0xffffff00=reserved, 0x000000ff=capabilities pointer
-// PCI 0x38: reserved
-// PCI 0x3c: 0x3c=int-line, 0x3d=int-pin, 0x3e=min-gnt, 0x3f=maax-lat
-
 #define CIRRUS_PNPMMIO_SIZE         0x1000
 
 #define ABS(a) ((signed)(a) > 0 ? a : -a)
@@ -3232,7 +3198,6 @@ static int pci_cirrus_vga_initfn(PCIDevice *dev)
      pci_config_set_vendor_id(pci_conf, PCI_VENDOR_ID_CIRRUS);
      pci_config_set_device_id(pci_conf, device_id);
      pci_config_set_class(pci_conf, PCI_CLASS_DISPLAY_VGA);
-     pci_conf[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL;
 
      /* setup memory space */
      /* memory #0 LFB */
-- 
1.6.5.2.143.g8cc62

[Qemu-devel] Re: [PATCHv5-repost 1/2] qemu: make cirrus init value pci spec compliant

[Avi Kivity]

On 11/30/2009 09:02 PM, Michael S. Tsirkin wrote:
> PCI memory should be disabled at reset, otherwise
> we might claim transactions at address 0.
> I/O should also be disabled, although for cirrus
> it is harmless to enable it as we do not
> have I/O bar.
>
> Note: bios fix needed for this patch to work
> was already applied:
> previously bios incorrently assumed that it does not
> need to enable i/o unless device has i/o bar.
>    

Is this for qemu-kvm.git or qemu.git?

-- 
error compiling committee.c: too many arguments to function

[Qemu-devel] Re: [PATCHv5-repost 1/2] qemu: make cirrus init value pci spec compliant

[Michael S. Tsirkin]

On Wed, Dec 02, 2009 at 02:52:33PM +0200, Avi Kivity wrote:
> On 11/30/2009 09:02 PM, Michael S. Tsirkin wrote:
>> PCI memory should be disabled at reset, otherwise
>> we might claim transactions at address 0.
>> I/O should also be disabled, although for cirrus
>> it is harmless to enable it as we do not
>> have I/O bar.
>>
>> Note: bios fix needed for this patch to work
>> was already applied:
>> previously bios incorrently assumed that it does not
>> need to enable i/o unless device has i/o bar.
>>    
>
> Is this for qemu-kvm.git or qemu.git?
>
> -- 
> error compiling committee.c: too many arguments to function

This for qemu.git

-- 
MST

[Qemu-devel] Re: [PATCHv5-repost 1/2] qemu: make cirrus init value pci spec compliant

[Avi Kivity]

On 12/02/2009 03:33 PM, Michael S. Tsirkin wrote:
> This for qemu.git
>    

Please set the To: header correctly to avoid confusion.

-- 
error compiling committee.c: too many arguments to function