From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from eggs.gnu.org ([2001:4830:134:3::10]:38008) by lists.gnu.org with esmtp (Exim 4.71) (envelope-from ) id 1WVJ0H-0007XJ-DO for qemu-devel@nongnu.org; Wed, 02 Apr 2014 07:06:51 -0400 Received: from Debian-exim by eggs.gnu.org with spam-scanned (Exim 4.71) (envelope-from ) id 1WVJ0B-0002CF-5O for qemu-devel@nongnu.org; Wed, 02 Apr 2014 07:06:45 -0400 Received: from mx1.redhat.com ([209.132.183.28]:63044) by eggs.gnu.org with esmtp (Exim 4.71) (envelope-from ) id 1WVJ0A-0002C5-TU for qemu-devel@nongnu.org; Wed, 02 Apr 2014 07:06:39 -0400 Received: from int-mx01.intmail.prod.int.phx2.redhat.com (int-mx01.intmail.prod.int.phx2.redhat.com [10.5.11.11]) by mx1.redhat.com (8.14.4/8.14.4) with ESMTP id s32B6bho020786 (version=TLSv1/SSLv3 cipher=DHE-RSA-AES256-SHA bits=256 verify=OK) for ; Wed, 2 Apr 2014 07:06:37 -0400 Date: Wed, 2 Apr 2014 13:07:08 +0300 From: "Michael S. Tsirkin" Message-ID: <20140402100708.GB10089@redhat.com> References: <1385085951-12729-1-git-send-email-vyasevic@redhat.com> <20140402085118.GA8781@redhat.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: Subject: Re: [Qemu-devel] [PATCH] net: Update netdev peer on link change List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , To: Yan Vugenfirer Cc: Vlad Yasevich , qemu-devel , stefanha@redhat.com On Wed, Apr 02, 2014 at 01:46:14PM +0300, Yan Vugenfirer wrote: > > On Apr 2, 2014, at 11:51 AM, Michael S. Tsirkin wrote: > > > On Thu, Nov 21, 2013 at 09:05:51PM -0500, Vlad Yasevich wrote: > >> When a link change occurs on a backend (like tap), we currently do > >> not propage such change to the nic. As a result, when someone turns > >> off a link on a tap device, for instance, then a guest doesn't see > >> that change and continues to try to send traffic or run DHCP even > >> though the lower-layer is disconnected. This is OK when the network > >> is set up as a HUB since the the guest may be connected to other HUB > >> ports too, but when it's set up as a netdev, it makes thinkgs worse. > >> > >> The patch addresses this by setting the peers link down only when the > >> peer is not a HUBPORT device. With this patch, in the following config > >> -netdev tap,id=net0 -device e1000,mac=XXXXX,netdev=net0 > >> when net0 link is turned off, the guest e1000 shows lower-layer link > >> down. This allows guests to boot much faster in such configurations. > >> With windows guest, it also allows the network to recover properly > >> since windows will not configure the link-local IPv4 address, and > >> when the link is turned on, the proper address address is configured. > >> > >> Signed-off-by: Vlad Yasevich > >> --- > >> net/net.c | 26 +++++++++++++++++--------- > >> 1 file changed, 17 insertions(+), 9 deletions(-) > >> > >> diff --git a/net/net.c b/net/net.c > >> index 0a88e68..8a084bf 100644 > >> --- a/net/net.c > >> +++ b/net/net.c > >> @@ -1065,15 +1065,23 @@ void qmp_set_link(const char *name, bool up, Error **errp) > >> nc->info->link_status_changed(nc); > >> } > >> > >> - /* Notify peer. Don't update peer link status: this makes it possible to > >> - * disconnect from host network without notifying the guest. > >> - * FIXME: is disconnected link status change operation useful? > >> - * > >> - * Current behaviour is compatible with qemu vlans where there could be > >> - * multiple clients that can still communicate with each other in > >> - * disconnected mode. For now maintain this compatibility. */ > > > > Hmm this went in without much discussion. > > > > But before this change went in, it was possible to control link state on NIC > > and on link separately, without guest noticing. > > > > Why did we decide to drop this functionality? > > Not sure there was a real need for the patch. > > On other hand Windows guest will not receive IP address from DHCP server if you start VM with tap link down and then set it to up without toggling link state of the guest device as well. > > Yan. So why not toggle the link of the guest device? > > > > > > > >> - if (nc->peer && nc->peer->info->link_status_changed) { > >> - nc->peer->info->link_status_changed(nc->peer); > >> + if (nc->peer) { > >> + /* Change peer link only if the peer is NIC and then notify peer. > >> + * If the peer is a HUBPORT or a backend, we do not change the > >> + * link status. > >> + * > >> + * This behavior is compatible with qemu vlans where there could be > >> + * multiple clients that can still communicate with each other in > >> + * disconnected mode. For now maintain this compatibility. > >> + */ > >> + if (nc->peer->info->type == NET_CLIENT_OPTIONS_KIND_NIC) { > >> + for (i = 0; i < queues; i++) { > >> + ncs[i]->peer->link_down = !up; > >> + } > >> + } > >> + if (nc->peer->info->link_status_changed) { > >> + nc->peer->info->link_status_changed(nc->peer); > >> + } > >> } > >> } > >> > >> -- > >> 1.8.4.2 > >> > >