[Qemu-devel] [PULL 06/11] cpus: move icount preparation out of tcg_exec_cpu

["Alex Bennée" <alex.bennee@linaro.org>]

As icount is only supported for single-threaded execution due to the
requirement for determinism let's remove it from the common
tcg_exec_cpu path.

Also remove the additional fiddling which shouldn't be required as the
icount counters should all be rectified as you enter the loop.

Signed-off-by: Alex Bennée <alex.bennee@linaro.org>

diff --git a/cpus.c b/cpus.c
index 7ec6473c02..6034b104c3 100644
--- a/cpus.c
+++ b/cpus.c
@@ -1179,47 +1179,64 @@ static void handle_icount_deadline(void)
     }
 }
 
-static int tcg_cpu_exec(CPUState *cpu)
+static void prepare_icount_for_run(CPUState *cpu)
 {
-    int ret;
-#ifdef CONFIG_PROFILER
-    int64_t ti;
-#endif
-
-#ifdef CONFIG_PROFILER
-    ti = profile_getclock();
-#endif
     if (use_icount) {
         int64_t count;
         int decr;
-        timers_state.qemu_icount -= (cpu->icount_decr.u16.low
-                                    + cpu->icount_extra);
-        cpu->icount_decr.u16.low = 0;
-        cpu->icount_extra = 0;
+
+        /* These should always be cleared by process_icount_data after
+         * each vCPU execution. However u16.high can be raised
+         * asynchronously by cpu_exit/cpu_interrupt/tcg_handle_interrupt
+         */
+        g_assert(cpu->icount_decr.u16.low == 0);
+        g_assert(cpu->icount_extra == 0);
+
+
         count = tcg_get_icount_limit();
+
         timers_state.qemu_icount += count;
         decr = (count > 0xffff) ? 0xffff : count;
         count -= decr;
         cpu->icount_decr.u16.low = decr;
         cpu->icount_extra = count;
     }
-    qemu_mutex_unlock_iothread();
-    cpu_exec_start(cpu);
-    ret = cpu_exec(cpu);
-    cpu_exec_end(cpu);
-    qemu_mutex_lock_iothread();
-#ifdef CONFIG_PROFILER
-    tcg_time += profile_getclock() - ti;
-#endif
+}
+
+static void process_icount_data(CPUState *cpu)
+{
     if (use_icount) {
         /* Fold pending instructions back into the
            instruction counter, and clear the interrupt flag.  */
         timers_state.qemu_icount -= (cpu->icount_decr.u16.low
                         + cpu->icount_extra);
-        cpu->icount_decr.u32 = 0;
+
+        /* Reset the counters */
+        cpu->icount_decr.u16.low = 0;
         cpu->icount_extra = 0;
         replay_account_executed_instructions();
     }
+}
+
+
+static int tcg_cpu_exec(CPUState *cpu)
+{
+    int ret;
+#ifdef CONFIG_PROFILER
+    int64_t ti;
+#endif
+
+#ifdef CONFIG_PROFILER
+    ti = profile_getclock();
+#endif
+    qemu_mutex_unlock_iothread();
+    cpu_exec_start(cpu);
+    ret = cpu_exec(cpu);
+    cpu_exec_end(cpu);
+    qemu_mutex_lock_iothread();
+#ifdef CONFIG_PROFILER
+    tcg_time += profile_getclock() - ti;
+#endif
     return ret;
 }
 
@@ -1306,7 +1323,13 @@ static void *qemu_tcg_rr_cpu_thread_fn(void *arg)
 
             if (cpu_can_run(cpu)) {
                 int r;
+
+                prepare_icount_for_run(cpu);
+
                 r = tcg_cpu_exec(cpu);
+
+                process_icount_data(cpu);
+
                 if (r == EXCP_DEBUG) {
                     cpu_handle_guest_debug(cpu);
                     break;
-- 
2.11.0